HT4928S Ver1.

1 1/6

www.hotchip.com.cn Mobile power management solution

Product description ◆ Highly integrated, few peripheral components; Output current 0.8A (typical value at 3.6V
The HT4928S is a highly integrated mobile power battery), with Constant power output function,
supply Management chip, built-in charge complete overcurrent, short circuit protection
management module, LED indicator Block, boost ◆ Highly integrated, few peripheral components; Load insertion automatically starts boost, load
discharge management module, and use small removal Automatic sleep
SOP8 Package, the periphery can be composed ◆ Highly integrated, few peripheral components; Battery low voltage reminder function;
of very few components Powerful mobile power ◆ Highly integrated, few peripheral components; Single/dual lamp charging and discharging
solution. instructions;
◆ Highly integrated, few peripheral components; Common input/output port, intelligent
Main features identification charging/discharging of electricity;
◆ Highly integrated, few peripheral components; Highly integrated, few peripheral components; ◆ Highly integrated, few peripheral components; 4KV ESD;
◆ Highly integrated, few peripheral components; Built-in fixed 0.8A linear charging mode; ◆ Highly integrated, few peripheral components; Fixed switching frequency 1MHZ;
◆ Highly integrated, few peripheral components; turbulent / constant current / constant voltage ◆ Highly integrated, few peripheral components; Battery overcharge and over discharge
three-stage charging, constant voltage 4.20V protection;
(typical), supporting charging of 0V battery; ◆ Highly integrated, few peripheral components; SOP8 small package
◆ Highly integrated, few peripheral components; Built-in charging can automatically reduce the
charging current according to the temperature Typical application
rise. 130 degrees begins to decline, and the ◆ Highly integrated, few peripheral components; Mobile power
minimum can be reduced to 0; ◆ Highly integrated, few peripheral components; LED lighting system
◆ Highly integrated, few peripheral components; The charging input has anti-backflow function, ◆ Highly integrated, few peripheral components; Toys
no need for anti-reverse irrigation diode;
◆ Highly integrated, few peripheral components; Boost uses synchronous rectification circuit,
the efficiency is up to 91%, Low heat, fixed 5.1V
output, no external resistor required

Typical application circuit diagram

www.hotchip.com.cn 1/6 Ver1.1

 HT4928S Ver1.1 1/6

www.hotchip.com.cn Mobile power management solution

Pin definition

SOP8 Pin name Pin number Function Description

L1 1 Indicator light 1
L2 2 Indicator light 2
BTP 3 Battery end
VOUT 4 Output voltage feedback
VO/IN 5 Output/input
LX 6 Inductance
PGND 7 Power ground
AGND 8 Analog ground

Circuit internal structure block diagram

www.hotchip.com.cn 2/6 Ver1.1

 HT4928S Ver1.1 1/6

www.hotchip.com.cn Mobile power management solution

Typical parameters
(Except for special instructions, all parameters are measured at room temperature and the potential
at the GND terminal is 0)

Symbol Description Test Unit Min Typ Max

Conditions
System parameters
V IN Input voltage range V 4.5 5 5.5
Vbat Battery voltage V 2.95 4.4
Charging parameter
V IN power down monitor VIN from low to high Vin>BAT mV 250
VIN from high to low Vin>BAT mV 50
V float Floating charge threshold voltage V 4.158 4.20 4.242
Ichg Recharging current VIN=4.75- A 0.8
5.25V
V TRKL Turbulent flow VBAT from V 2.8
low to high
V TRHYS Trickle charging hysteresis voltage mV 100
V RECHG Recharge threshold voltage V 4.1
Discharge parameter
Vo Boost system output voltage V 4.95 5.1 5.25
Iout Output current BAT=3.6V A 0.8
Vout>4.8V
V OVP Output overvoltage protection V 5.8
V OVP_DIS V 5.4
V UVLO Boost undervoltage protection BAT from V 2.95
high to low
V UVLO_R Boost undervoltage recovery BAT from low V 3.20
to high
I BAT1 Vout=5.5V mA 0.2
No Switching
I BAT2 Vout=4.5V mA 1
Switching
Iauto_off Automatic shutdown load current BAT=3.6V mA 60
Cout=20uF
Iq Quiescent Current BAT=3.6V uA 13 30
F OSC Working frequency MHz 1
OTP Over temperature protection degC 150
OTP_HYS Hysteresis degC 20

www.hotchip.com.cn 3/6 Ver1.1

 HT4928S Ver1.1 1/6

www.hotchip.com.cn Mobile power management solution

Function and parameters 2. When the battery is fully charged, plug in the
Charging management module charging indicator LD2 during charging. On, the
1. The charging current is internally set to 0.8A LD2 indicator goes off after unplugging the
2. Battery voltage is lower than 2.8V with pre- phone for 8 seconds.
charging function (current =Ich*10%) 3. If the battery voltage is lower than 3.2V during
3. Support charging 0V battery discharge, the indicator light LD2 Flashes until
4. Three-stage charging: turbulent, constant 2.95V undervoltage shutdown; when the battery
current, constant voltage charging voltage rises to Before 3.2V, the load LD2
5. The charging current decreases with the indicator will flash for 8 seconds, but Boost will
increase of temperature, and it is opened at 130 not start.
°C. Start to decrease; 4. If LD1 is not connected, it will be in single LED
mode.
Boost module
1. Standby state detection load is greater than Charger detection during single port
10uA (typ) current When the boost is discharge
automatically started, when the output load is 1. During the charging process of the mobile
less than 60mA Type value) delays 8 seconds to phone, the system will generate a week at the
automatically enter standby mode output. a charger detection signal with a pulse
2. Synchronous rectification boost, up to 91% width of 4 mS for 2 seconds;
conversion efficiency, output Fixed voltage 5.1V 2. When there is no charger inserted, at 4mS
3. After the output current exceeds 0.8A, the pulse, output The voltage was reduced to 4.7V,
voltage starts to decrease. and it was judged that the charger was not
4. Overvoltage protection is performed after the inserted outside.
output voltage is greater than 5.8V, when the 3. When the charger is inserted, when the
output is Automatic recovery after the voltage voltage is greater than 4.7V, the system
drops to 5.4V automatically enters 4mS pulse, output voltage
5. With output overcurrent protection and short trickle state.
circuit protection, through plugging and
unplugging Automatic load release PCB LAYOUT Reference
6. Switching frequency 1MHz
7. During the discharge process, if the
temperature reaches 150 degrees, the overheat
protection Automatically turn off the output and
enter standby.

Automatic conversion module

1. Support side charging, that is, the external
charger simultaneously charges the mobile
phone Electricity, also charging mobile power
2. During the boosting process, automatically
detect whether the external charger is plugged
in. In, after detecting the insertion of the charger,
according to the external current Automatically
distribute current to charge mobile power and
mobile phones
3. If the charger is removed, the boost is
automatically started.
C1, C2 should be close to the chip within 2mm,
Charge and discharge indicator and go to the chip pin The line is as short as
1. When charging, the indicator lights LD1 and possible; to prevent the heat of L1 from affecting
LD2 flash alternately. The indicator light LD2 is the chip, L1 can be a little farther away.
on; Connected by thick wire at around 5-10mm

www.hotchip.com.cn 4/6 Ver1.1

 HT4928S Ver1.1 1/6

www.hotchip.com.cn Mobile power management solution

Electrostatic protection Check:

CMOS circuits are electrostatically sensitive 1. The operator should be grounded through the
devices that are manufactured and shipped. The static-discharge wrist strap;
following precautions must be taken during the 2. The outer casing of the production equipment
process to prevent CMOS circuit damage due to must be grounded;
electrostatic discharge 3. The tools used in the assembly process must
be grounded;
4. Must be packaged or shipped in
semiconductor packaging or antistatic materials.

Package information
SOP8 package appearance

www.hotchip.com.cn 5/6 Ver1.1

 HT4928S Ver1.1 1/6

www.hotchip.com.cn Mobile power management solution

Device identification and ordering information

Company LOGO

Product number

Product batch

Package form Chip surface Procurement Package style Minimum package

identification device name quantity

SOP8 Pb-free HT4928S HT4928S-F0 disk mounted 4000PCS

Important statement
◆ Highly integrated, few peripheral components; Huaxin State reserves the right to change the instructions, please refer to the description
information published by Huaxinbang official website without prior notice.
◆ Highly integrated, few peripheral components; The company is not responsible for problems related to industry standards, patents or third party
rights arising from circuit or diagram descriptions. Application circuit diagram only as The exemplary
use of a typical application does not guarantee its utility for specialized mass production.
◆ Highly integrated, few peripheral components; When the product and derivative products do not conform to the Vaisha Agreement or other
international agreements, the export may require authorization from the relevant government
department.
◆ Highly integrated, few peripheral components; Any reproduction or copying of the information described herein for other purposes without the
permission of the company is strictly prohibited.
◆ Highly integrated, few peripheral components; The information described here cannot be used for human-related equipment, such as sports
machinery or medical equipment, without the written permission of the company. Equipment, safety
systems, gas equipment, or any other aircraft or other means of transport.
◆ Highly integrated, few peripheral components; Although the company tries its best to improve the quality and reliability of the products, the
failure and failure of the products are still inevitable. Therefore, customers who use this product must
Careful safety design, including redundant design, fire protection design, and fail-safe protection
against any secondary accidents, fire or related damage.
◆ Highly integrated, few peripheral components; Product improvement is endless, our company will wholeheartedly provide customers with better
products.

www.hotchip.com.cn 6/6 Ver1.1