Scribd
Upload
85 views2 pages

Etape: Continuous Fluid Level Sensor Pn-12110215Tc-X

The eTape sensor is a solid state, continuous fluid level sensor that uses printed electronic technologies to produce a resistive output inversely proportional to liquid level. It can measure levels in water and water-based liquids between 15-150°F. The sensor's resistance changes with hydrostatic pressure, allowing it to provide level readings between 0.01-12 inches. It connects via crimpflex pins and can be installed in pipes or suspended in containers using adhesive tape. Custom lengths are available upon request.

Uploaded by

Mohsin raza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views2 pages

Etape: Continuous Fluid Level Sensor Pn-12110215Tc-X

The eTape sensor is a solid state, continuous fluid level sensor that uses printed electronic technologies to produce a resistive output inversely proportional to liquid level. It can measure levels in water and water-based liquids between 15-150°F. The sensor's resistance changes with hydrostatic pressure, allowing it to provide level readings between 0.01-12 inches. It connects via crimpflex pins and can be installed in pipes or suspended in containers using adhesive tape. Custom lengths are available upon request.

Uploaded by

Mohsin raza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Continuous Fluid Level Sensor

eTape
TM

PN-12110215TC-X

Description
The eTape sensor is a solid state, continuous (multi-level) fluid level sensor for measuring levels in
water, non-corrosive water based liquids and dry fluids (powders). The eTape sensor is
manufactured using printed electronic technologies which employ additive direct printing
processes to produce functional circuits.
Theory of Operation
The eTape sensor's envelope is compressed by hydrostatic pressure of the fluid in which it is
immersed resulting in a change in resistance which corresponds to the distance from the top of
the sensor to the fluid surface. The eTape sensor provides a resistive output that is inversely
proportional to the level of the liquid: the lower the liquid level, the higher the output resistance;
the higher the liquid level, the lower the output resistance.
Specifications
Part Number PN-12110215TC-8 PN-12110215TC-12 PN-12110215TC-24 PN-12110215TC-32
Nominal Length 8-inch 12-inch 24-inch 32-inch
Sensor Length 10.2" (259 mm) 14.2" (361 mm) 26.0" (660 mm) 34.2" (869 mm)
Active Length 8.4" (213 mm) 12.4" (315 mm) 24.34" (618 mm) 32.4" (823 mm)
Sensor Output 400-1500 ±20% 400-2000 ±20% 400-4000 ±20% 400-5000 ±20%
Ref Resistance 1500 ±20% 2000 ±20% 4000 ±20% 5000 ±20%

Thickness: 0.015" (0.381mm) Width: 1.0" (25.4 mm)


Actuation Depth: Nominal 1” (25.4 mm) Resolution: < 0.01“(0.25 mm)
Resistance Gradient: 150 /inch (60/cm) Connector: Male Crimpflex Pins
Power Rating: 0.5 Watts (VMax = 10V) Temperature Range: 15°F - 150°F (-9°C - 65°C)

Sensor Output
The eTape can be modeled as a variable resistor. The typical output characteristics of the
eTape sensor are show in the figure below:

Typical eTape Sensor Output - PN 12110215TC-12


2.40
2.30
2.20
2.10
2.00
1.90
Sensor Output (Kohms)

1.80
1.70
1.60
1.50
1.40
1.30
1.20
1.10
1.00
0.90
0.80
0.70
0.60
0.50
0.40
0.30
0.20
0.10
0.00
0 1 2 3 4 5 6 7 8 9 10 11 12 13
Liquid Level (Inches)

Milone Technologies, Inc - 17 Ravenswood Way - Sewell, New Jersey 08080 - Phone: (856) 270-2688
Email: [email protected] Web: www.milonetech.com
Continuous Fluid Level Sensor
eTape
TM

PN-12110215TC-12

Connection and Installation


Connect to the eTape by attaching a 4 pin connector with pre-soldered wires to the Crimpflex
pins. Do not solder directly to the Crimpflex pins. The inner two pins (pins 2 and 3) are the
sensor output (Rsense). The outer pins (pins 1 and 4) are the reference resistor (Rref) which can
be used for temperature compensation. Suspend the eTape sensor in the fluid to be
measured. To work properly the sensor must remain straight and must not be bent vertically or
longitudinally. For best results install the sensor inside a section of 1-inch diameter PVC pipe.
Double sided adhesive tape may be applied to the upper back portion of the sensor to
suspend the sensor in the container to be measured. However, the liquid must be allowed to
interact freely with both sides of the sensor. The vent hole located above the max line allows
the eTape to equilibrate with atmospheric pressure. The vent hole is fitted with a hydrophobic
filter membrane to prevent the eTape from being swamped if inadvertently submerged.

Sample Circuits

Custom Applications
The eTape sensor can be manufactured in custom lengths to fit any application.
Contact Milone Technologies if you have an application that requires specific
length, configuration or output characteristics.

Technical Support
If you require technical support for the eTape liquid level sensor, please contact our technical
support department by email at: [email protected].

Innovative Fluid Sensing

Milone Technologies, Inc - 17 Ravenswood Way - Sewell, New Jersey 08080 - Phone: (856) 270-2688
Email: [email protected] Web: www.milonetech.com

You might also like