10G SFP BIDI 20KM data sheet

Features：
Support 10GBASE-LR/10GBASE-LW/10G Fiber Channel application
Compliant to SFP+ Electrical MSA SFF-8431
Compliant to SFP+ Mechanical MSA SFF-8432
Multi rate of up to 11.3Gbps
Transmission distance up to 20KM
+3.3V single power supply
Low power consumption
Operating case temp : 0~+70°C
RoHS 6/6 compliant

Absolute Maximum Ratings

Table 1- Absolute Maximum Ratings
Parameter Symbol Min. Typical Max. Unit Notes
Supply Voltage Vcc3 -0.5 +3.6 V
-
Storage Temperature Ts 0 +70 °C
-
Operating Humidity RH +5 +95 %
-

Recommended Operating Conditions

Table 2- Recommended operating Conditions
Parameter Symbol Min. Typical Max. Unit Notes
Operating Case Temperature TC 0 +70 °C
-
Power Supply Voltage Vcc 3.14 3.3 3.47 V
Power Supply Current Icc - 300 mA
-
Power Dissipation Pd - 1.0 W
-
Bit Rate BR - 10.3125 Gbps
-

Email:[email protected] Website:www.hifibercom.com
 10G SFP BIDI 20KM data sheet

Electrical Characteristics
Table 3- Electrical Characteristics
Parameter Symbol Min. Typ. Max. Units Notes

Differential Data Input Swing Vin,P-P 120 850 mVPP

-
Input Differential Impedance ZIN 80 100 120 Ω
Normal Operation
VOL 0 0.8 V
-
Tx
Transmitter Fault
_ VOH 2.0 VCC V
-
F
Normal Operation 0 0.8 V
VIL
Tl a -
u Disable
xLaser VIH 2.0 VCC+0.3 V
t -
_
D
Differential
i Date Output Vout 100 800 mV
-
sOutput Differential Impedance ZD 80 100 120 Ω
a
Output Rise Time(20-80%) TR 24 ps
b - -
Output Fall Time (20-80%) TF 24 ps
l - -
eNormal Operation
0
VOLTransmitter 0.8 V
R -
x
Lose Signal VoH 2.0 VCC V
_ -
L
O
Optical
S Characteristics
Table 4-Optical Characteristics
HFCSFP-BIDI-20K01 (10G 1330TX 1270RX 20KM)

Parameter Symbol Unit Min. Typ. Max. Notes

Bit Rate BR Gbps 9.953 10.3125 11.3

Center Wavelength 1250 1270 1290
λ c nm
Range 1310 1330 1350
Average Launch
Poff dBm -45
power Tx_off - -

Receiver
Email:[email protected] Website:www.hifibercom.com
 10G SFP BIDI 20KM data sheet

Launch Optical Power P0 dBm -5.2 1 1

-
Extinction Ratio ER dB 3.5
- -
Jitter P-P JP ps 27
- -
Jitter RMS JR ps 5
- -
Optical Rise/Fall time Tr/tf ps 100
- -
Eye Diagram Compliant With IEEE 802.3-2005
Optical receiver Characteristics
Bit Rate BR Gbps 9.953 10.3125 11.3
Receiver Sensitivity RS dBm -14 2
- -
Overload Input Optical
PIN dBm 0 2
Power - -
Center Wavelength 1310 1330 1350
λ c nm
Range 1250 1270 1290
LOSD -15
LOS dBm - -
LOSA -24.5
- -
LOS Hysteresis dB 0.5
- -

Email:[email protected] Website:www.hifibercom.com
 10G SFP BIDI 20KM data sheet

Recommened interface Circuit

Figure 1, Recommended Interface Circuit

Email:[email protected] Website:www.hifibercom.com
 10G SFP BIDI 20KM data sheet

Recommended Host Board Power Supply Circuit

Figure 2, Recommended Host Board Power Supply Circuit

Pin arrangement

Figure 3, Pin View

Email:[email protected] Website:www.hifibercom.com
 10G SFP BIDI 20KM data sheet

Table 5-Pin Function Definitions

Pin Symbol Name/Description Notes

1 VEET Module Transmitter Ground 1
2 TX_FAULT Module Transmitter Fault 2
3 TX_DISABLE Transmitter Disable; Turns off transmitter laser output 3
4 SDA 2-Wire Serial Interface Data Line (MOD-DEF2)
5 SCL 2-Wire Serial Interface Clock (MOD-DEF1)
6 MOD_ABS Module Absent, connected to VEET or VEER in the 2
Rate Select 0, optionalldy clontrols SFP+ module RS0 receiver
7 as the following when HIGH input Bit Rate>4.25 Gbps

Recdeivehr LoLssOWoif StigBniat Rl Intdic≤a4tio2n5 (Ginb FC

8 RX_LOS designated as RX_LOS, in SONET designated asLOS, 2

d i Etht d i t d NOT Si l D t t) Rate Select 1, optionally controls SFP+ module

transmitter as the following when HIGH input RS1
9 Bit Rate>4.25 Gbps and when LOW input Bit Rate ≤4.25 Gbps.

10 VEER Module Receiver Ground 1

11 VEER Module Receiver Ground 1
12 RD- Receiver Inverted Data Output
13 RD+ Receiver Non-Inverted Data Output
14 VEER Module Receiver Ground 1
15 VCCR Module Receiver 3.3 V Supply
16 VCCT Module Transmitter 3.3 V Supply
17 VEET Module Transmitter Ground 1
18 TD+ Transmitter Non-Inverted Data Input
19 TD- Transmitter Inverted Data Input
20 VEET Module Transmitter Ground 1
Note:
1. The module ground pins are isolated from the module case.
2. The pins shall be pulled up with 4.7K-10Kohms to a voltage between 3.14V and 3.46V
on host board.
3. The pin is pulled up to VCCT with a 4.7K-10KΩ resistor in the module.

Email:[email protected] Website:www.hifibercom.com
 10G SFP BIDI 20KM data sheet

Digital Diagnostic Memory Map

Figure 4, Memory Map

Mechanical Diagram

Figure 5, Mechanical Diagram

Email:[email protected] Website:www.hifibercom.com
 10G SFP BIDI 20KM data sheet

Order Information
Table 6-Order Information
Bit Rate Laser Laser Fiber
Part No. Distance Connector
(Gbps) TX(nm) RX(nm) Type
Simplex LC
HFCSFP-BIDI-20K01 10.3125 1270 1330 SMF 20KM
Receptacle
Simplex LC
HFCSFP-BIDI-20K02 10.3125 1330 1270 SMF 20KM
Receptacle

Notice
HIFIBERCOM reserves the right to make changes to or discontinue any optical link
product or service identified in this publication, without notice, in order to improve
design and/or performance. Applications that are described herein for any of the optical
link products are for illustrative purposes only. HIFIBERCOM makes no representation
or warranty that such applications will be suitable for the specified use without further
testing or modification.

Contact
Shenzhen Hifibercom Technology Co.,Ltd
Factory Add : A8 First Floor Silicon Valley Power,Longhua District, Shenzhen, China
518040
Tel:+86(0)0755- 2107 4669
Fax:+86(0)0755-2107 4669
Email:[email protected]
Website:www.hifibercom.com

Email:[email protected] Website:www.hifibercom.com