Scribd
Upload
155 views

Types of Resistance: Fixed Resistors

Resistors are used to oppose the flow of electrons in a circuit. There are two main types - fixed resistors, which have a set resistance value, and variable resistors, which allow the resistance to be adjusted. Fixed resistors include carbon film and metal film resistors. Resistance values are indicated using color codes on the resistor body. Other types of resistors discussed include wire wound, ceramic, single-in-line network, 4S-network, light dependent, thermistor, and variable resistors. Resistor power ratings and Ohm's law relationships between voltage, current and resistance are also covered.

Uploaded by

Fatima Sehar
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
155 views

Types of Resistance: Fixed Resistors

Resistors are used to oppose the flow of electrons in a circuit. There are two main types - fixed resistors, which have a set resistance value, and variable resistors, which allow the resistance to be adjusted. Fixed resistors include carbon film and metal film resistors. Resistance values are indicated using color codes on the resistor body. Other types of resistors discussed include wire wound, ceramic, single-in-line network, 4S-network, light dependent, thermistor, and variable resistors. Resistor power ratings and Ohm's law relationships between voltage, current and resistance are also covered.

Uploaded by

Fatima Sehar
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

To oppose the flow of electrons ( current). The symbols are shown below.

Resistance is measured in units called “Ohm”. 1000 ohms is shown as 1k ohm (103 ohm) and
1000 k ohm is shown as M.ohms (106ohm).

Resistors can be broadly of two types.

• Fixed Resistors and Variable Resistors.

Fixed Resistors:
Carbon Film (5%, 10% tolerance) and Metal Film Resistors (1%,2% tolerances) and wire wound

resistors. A fixed resistor is one for which the value of its resistance is specified and cannot be
varied in general.

Resistance Value
The resistance value is displayed using the color code ( the colored bars/the colored stripes),
because the average resistor is too small to have the value printed on it with numbers. The
resistance value is a discrete value.

For example, the values [1], [2.2], [4.7] and [10] are used in a typical situation.

Types of Resistance
CARBON FILM RESISTORS
This is the most general purpose, cheap resistor. Usually the tolerance of the resistance value is
±5%. Power ratings of 1/8W, 1/4W and 1/2W are frequently used. The disadvantage of using
carbon film resistors is that they tend to be electrically noisy.

METAL FILM RESISTORS


Metal film resistors are used when a higher tolerance (more accurate value) is needed.
Nichrome(Ni-Cr) is generally used for the material of resistor. They are much more accurate in
value than carbon

film resistors. They have about ±0.05% tolerance.

OTHER RESISTORS
There is another type of resistor called the wire wound resistor. A wire wound resistor is made of
metal

resistance wire, and because of this, they can be manufactured to precise values. Also, high-
wattage resistors can be made by using a thick wire material. Wire wound resistors cannot be
used for high-frequency circuits.

Ceramic Resistor
Another type of resistor is the Ceramic resistor. These are wire wound resistors in a ceramic
case, strengthened with a special cement. They have very high power ratings, from 1 or 2 watts
to dozens of watts. These resistors can become extremely hot when used for high power
applications, and this must be taken into account when designing the circuit.

SINGLE-IN LINE NETWORK RESISTORS


It is made with many resistors of the same value, all in one package. One side of each resistor is
connected with one side of all the other resistors inside. One example of its use would be to
control the current in a circuit powering many light emitting diodes (LEDs). The face value of
the resistance is printed.
4S-RESISTOR NETWORK
The 4S indicates that the package contains 4 independent resistors that are not wired together
inside. The housing has eight leads instead of nine.

VARIABLE RESISTORS
There are two general ways in which variable resistors are used. One is the variable resistor
whose value is easily changed, like the volume adjustment of Radio. The other is semi-fixed
resistor that is not meant to be adjusted by anyone but a technician. It is used to adjust the
operating condition of the circuit by the technician.

Semi-fixed resistors are used to compensate for the inaccuracies of the resistors, and to fine-tune
a circuit. The rotation angle of the variable resistor is usually about 300 degrees. Some variable
resistors must be turned many times( multi-turn Pot) to use the whole range of resistance they
offer.

This allows for very precise adjustments of their value. These are called “Potentiometers” or
“Trimmer Potentiometers” or “presets”.

LIGHT DEPENDENT RESISTANCE (LDR)


Some components can change resistance value by changes in the amount of light falling on them.
One type is the Cadmium Sulfide Photocell. It is a kind of resistor, whose value depends on the
amount of light falling on it. When in darkness its resistance if very large and as more and more
light falls on it its resistance becomes smaller and smaller.

There are many types of these devices. They vary according to light sensitivity, size, resistance
value etc.

THERMISTOR
They are thermally sensitive resistor. The resistance value of the thermistor changes according to
temperature. They are used as a temperature sensor. There are generally two types of thermistors,
with Negative Temperature Coefficient(NTC) Positive Temperature Coefficient(PTC). The
resistance of NTC thermistors decreases on heating while that of PTC thermistors increases.
ELECTRIC POWER RATING
For example, to power a 3V circuit using a 12V supply, using only a resistor, then we need to
calculate the power rating of the resistor as well as the resistance value. The current consumed
by the 5V circuit needs to be known.

Assume the current consumed is 250 mA (milliamps) in the above example. That means 9V
(=12-3 V) must be dropped with the resistor. The resistance value of the resistor becomes 9V /
0.25A = 36(ohm).

The consumption of electric power for this resistor becomes 0.25A x 0.25A x 36ohm = 2.25W.
Thus the selection of resistors depends on two factors namely tolerance and electric power
ratings.

OHM’S LAW
Important and useful law.The current(I) flowing through a conductor is proportional to the
voltage (V) applied across its ends. This can be written in algebraic form as V ∝ I Or V = IR
where R is the proportionality constant. R is called Resistance and is measured in ‘Ohms’ ( Ω ).
Usually resistors are also specified in circuits in kilo Ohms(kΩ) and Mega Ohms(MΩ). The
other useful relationships are V = RI, and R=V/I.

Source : http://electronichobbyist.wordpress.com/2012/03/02/
basic-electronics-2/

You might also like