Objective Electronics

TYPICAL QUESTIONS & ANSWERS

PART - I
OBJECTIVE TYPE QUESTIONS

Each Question carries 2 marks.

Choose correct or the best alternative in the following:

Q.1 The breakdown mechanism in a lightly doped p-n junction under reverse biased condition is
called
(A) avalanche breakdown.
(B) zener breakdown.
(C) breakdown by tunnelling.
(D) high voltage breakdown.

Ans: A

Q.2 In a CE – connected transistor amplifier with voltage – gain A v, the capacitance Cbc is
amplified by a factor
(A) (B)
(C) (D)

Ans: B

Q.3 For a large values of |VDS|, a FET – behaves as
(A) Voltage controlled resistor.
(B) Current controlled current source.
(C) Voltage controlled current source.
(D) Current controlled resistor.

Ans: C

Q.4 Removing bypass capacitor across the emitter-leg resistor in a CE amplifier causes
(A) increase in current gain. (B) decrease in current gain.
(C) increase in voltage gain. (D)decrease in voltage gain.

Ans: D

Q.5 For an op-amp having differential gain Av and common-mode gain Ac the CMRR is given by
(A) (B)
(C) (D)

Ans: B
Q.6 When a step-input is given to an op-amp integrator, the output will be
(A) a ramp.
(B) a sinusoidal wave.
(C) a rectangular wave.
(D) a triangular wave with dc bias.

Ans: A

Q.7 Hysteresis is desirable in Schmitt-trigger, because
(A) energy is to be stored/discharged in parasitic capacitances.
(B) effects of temperature would be compensated.
(C) devices in the circuit should be allowed time for saturation and desaturation.
(D) it would prevent noise from causing false triggering.

Ans: C

Q.8 In a full-wave rectifier without filter, the ripple factor is
(A) 0.482 (B) 1.21
(C) 1.79 (D) 2.05

Ans: A

Q.9 A minterm of the Boolean-function, f(x, y, x) is
(A) (B)
(C) x z (D) (y +z) x

Ans: B

Q.10 The minimum number of flip-flops required to
construct a mod-75 counter is
(A) 5 (B) 6
(C) 7 (D) 8

Ans: C

Q.11 Space charge region around a p-n junction
(A) does not contain mobile carriers
(B) contains both free electrons and holes
(C) contains one type of mobile carriers depending on the level of doping of the p
or n regions
(D) contains electrons only as free carriers

Ans: A

Q.12 The important characteristic of emitter-follower is
(A) high input impedance and high output impedance
(B) high input impedance and low output impedance
(C) low input impedance and low output impedance
(D) low input impedance and high output impedance
Ans: B

Q.13 In a JFET, at pinch-off voltage applied on the gate
(A) the drain current becomes almost zero
(B) the drain current begins to decrease
(C) the drain current is almost at saturation value.
(D) the drain-to-source voltage is close to zero volts.

Ans: C

Q.14 When an amplifier is provided with current series
feedback, its
(A) input impedance increases and output impedance decreases
(B) input and output impedances both decrease
(C) input impedance decreases and output impedance increases
(D) input and output impedances both increase

Ans: D

Q.15 The frequency of oscillation of a tunnel-collector
oscillator having L= 30μH and C = 300pf is nearby
(A) 267 kHz (B) 1677 kHz
(C) 1.68 kHz (D) 2.67 MHz

Ans: B

Q.16 The open-loop gain of an op-amp available in the
market may be around.
(A) 10–1 (B) 10
(C) 105 (D) 102

Ans: C

Q.17 The control terminal (pin5) of 555 timer IC is
normally connected to ground through a capacitor (~ 0.01μF). This is to
(A) protect the IC from inadvertent application of high voltage
(B) prevent false triggering by noise coupled onto the pin
(C) convert the trigger input to sharp pulse by differentiation
(D) suppress any negative triggering pulse

Ans: B

Q.18 The value of ripple factor of a half-wave rectifier without filter is approximately
(A) 1.2 (B) 0.2
(C) 2.2 (D) 2.0

Ans: A
Q.19 The three variable Boolean expression xy + xyz + y + x z
(A) (B)
(C) (D)

Ans: C

Q.20 The fan-out of a MOS-logic gate is higher than that of TTL gates because of its
(A) low input impedance (B) high output impedance
(C) low output impedance (D) high input impedance

Ans: D

Q.21 In an intrinsic semiconductor, the Fermi-level is
(A) closer to the valence band
(B) midway between conduction and valence band
(C) closer to the conduction band
(D) within the valence band

Ans: C

Q.22 The reverse – saturation current of a silicon diode
(A) doubles for every 10C increase in temperature
(B) does not change with temperature
(C) halves for every 1C decrease in temperature
(D) increases by 1.5 times for every 2C increment in temperature

Ans: A

Q.23 The common collector amplifier is also known as
(A) collector follower (B) Base follower
(C) Emitter follower (D) Source follower

Ans: C

Q.24 In class–A amplifier, the output current flows for

(A) a part of the cycle or the input signal.
(B) the full cycle of the input signal.
(C) half the cycle of the input signal.
(D) 3/4th of the cycle of the input signal.

Ans: B

Q.25 In an amplifier with negative feedback
(A) only the gain of the amplifier is affected
(B) only the gain and bandwidth of the amplifier are affected
(C) only the input and output impedances are affected
(D) All of the four parameters mentioned above would be affected

Ans: D

Q.26 Wien bridge oscillator can typically generate frequencies in the range of
(A) 1KHz – 1MHz
(B) 1 MHz – 10MHz
(C) 10MHz – 100MHz
(D) 100MHz – 150MHz

Ans: A

Q.27 A differential amplifier, amplifies
(A) and mathematically differentiates the average of the voltages on the two input
lines
(B) and differentiates the input waveform on one line when the other line is
grounded
(C) the difference of voltages between the two input lines
(D) and differentiates the sum of the two input waveforms

Ans: C

Q.28 The transformer utilization factor of a half-wave rectifier is approximately
(A) 0.6 (B) 0.3
(C) 0.9 (D) 1.1

Ans: B
0.286 0.3

Q.29 The dual of the Boolean expression: x + y + z is
(A) (B)
(C) (D)

Ans: C

Q.30 It is required to construct a counter to count upto 100(decimal). The minimum number
of flip-flops required to construct the counter is

(A) 8 (B) 7
(C) 6 (D) 5

Ans: A
Q.31 The power conversion efficiency of an output stage is defined as_______.
(A) (Load power + supply power) / supply power
(B) (Load power + supply power) / (load power-supply power)
(C) Load power / supply power
(D) Supply power / load power

Ans. (C)
Power gain is defined as the ratio of output signal power to that of input signal power.

Q.32 A highly stable resonance characteristic is the property of a ____ oscillator.
(A) Hartley (B) Colpitts

(C) Crystal (D) Weinbridge

Ans. (C)

Q.33 The gate that assumes the 1 state, if and only if the input does not take a 1 state is
called________.
(A) AND gate (B) NOT gate
(C) NOR gate (D) Both (B) & (C)

Ans. (D)
Y= therefore output is high only when the values of both A and B are 0.

Q.34 The width of depleted region of a PN junction is of the order of a few tenths of a
___________.

(A) millimeter (B) micrometer
(C) meter (D) nanometer

Ans. (B)

Q.35 For NOR circuit SR flip flop the not allowed condition is ________.
(A) S=0, R=0. (B) S=0, R=1.
(C) S=1, R=1. (D) S=1, R=0.

Ans. (C)
When S=R=1 the output is subject to unpredictable behaviour when S and R return to
0 simultaneously.

Q.36 In negative feedback the return ratio is __________.
(A) 0 (B) 1
(C) greater than 0 (D) greater than 1

Ans. (C)
In a negative feed back circuit, always the return ratio will be in the range of 0 to 1.

Q.37 A phase shift oscillator uses __________________.
(A) LC tuning (B) Piezoelectric crystal
(C) Balanced bridge (D) Variable frequency operation

Ans.
(C)

Q.38 The voltage gain of basic CMOS is approximately _________.
(A) (gmro)/2 (B) 2gmro
(C) 1 / (2gmro) (D) 2ro / gm

Ans. (A)

Q.39 Transistor is a
(A) Current controlled current device.
(B) Current controlled voltage device.
(C) Voltage controlled current device.
(D) Voltage controlled voltage device.

Ans. (A)
The output current depends on the input current.

Q.40 A bistable multivibrator is a
(A) Free running oscillator. (B) Triggered oscillator.
(C) Saw tooth wave generator. (D) Crystal oscillator.

Ans. (B)
The transistors would change their state of operation from ON to OFF and vice
versa depending on the external trigger provided.

Q.41 If the output voltage of a bridge rectifier is 100V, the PIV of diode will be
(A) 100√2V (B) 200/π V
(C) 100πV (D) 100π/2 V

Ans. (D)
Peak inverse voltage = max secondary voltage
Vdc=2Vm/ π =100
Vm=100 π /2

Q.42 In the voltage regulator shown below, if the current through the load decreases,
(A) The current through R1 will increase.

(B) The current through R1 will decrease.
(C) zener diode current will increase.
(D) zener diode current will decrease.

Ans. (C)

Q.43 In Boolean algebra A + AB
(A) A + B
(B) A + B
(C) A + B
(D) A +B

Ans.
(A)
A.1+A B= A (1+B) +A B = A + AB +A B = A+B (A +A) = A+B

Q.44 For a JFET, when VDS is increased beyond the pinch off voltage, the drain current
(A) Increases
(B) decreases
(C) remains constant.
(D) First decreases and then increases.

Ans. (C)
At pinch off voltage drain current reaches its maximum off. Now if we further
increase VDS above Vp the depletion layer expands at the top of the channel. The
channel acts as a current limiter & holds drain current constant

Q.45 The type of power amplifier which exhibits crossover distortion in its output is
(A) Class A (B) Class B
(C) Class AB (D) Class C

Ans. (B)
The transistors do not conduct until the input signal is more than cut-in voltage of
the B-A junction. In class B, the devices being biased at cut-off, one device stops
conducting before the other device starts conducting leaving to Cross-over
distortion.

Q.46 The main advantage of a crystal oscillator is that its output is
(A) 50Hz to 60Hz (B) variable frequency
(C) a constant frequency. (D) d.c

Ans. (C)
The quality factor (Q) of a crystal as a resonating element is very high, of the
order of thousands. Hence frequency of a crystal oscillator is highly stable.

Q.47 The lowest output impedance is obtained in case of BJT amplifiers for
(A) CB configuration.
(B) CE configuration.
(C) CC configuration.
(D) CE with RE configuration.

Ans. (C)
The output impedance in case of CC configuration is on the order of a few ohms.
(In case of CB ≈ 450kΩ and in case of CE ≈ 45kΩ)

Q.48 N-channel FETs are superior to P-channel FETs, because
(A) They have higher input impedance
(B) They have high switching time
(C) They consume less power
(D) Mobility of electrons is greater than that of holes

Ans. (D)

Q.49 The upper cutoff frequency of an RC coupled amplifier mainly depends upon
(A) Coupling capacitor
(B) Emitter bypass capacitor
(C) Output capacitance of signal source
(D) Inter-electrode capacitance and stray shunt capacitance

Ans. (D)

Q.50 Just as a voltage amplifier amplifies signal-voltage, a power amplifier
(A) Amplifies power
(B) Amplifies signal current
(C) Merely converts the signal ac power into the dc
power
(D) Merely converts the dc power into useful ac power

Ans. (D)

Q.51 A radio frequency signal contains three frequency components, 870 KHz, 875 KHz
and 880 KHz. The signal needs to be amplified. The amplifier used should be
(A) audio frequency amplifier (B) wide band amplifier
(C) tuned voltage amplifier (D) push-pull amplifier

Ans. (C)
We need to amplify 3 signal frequencies i.e., 870 kHz, 875 kHz and 880 kHz.
These frequencies lie in a bandwidth of 10 kHz and we should use only tuned
voltage amplifiers to amplify them.

Q.52 An oscillator of the LC type that has a split capacitor in the circuit is
(A) Hartley oscillator
(B) Colpitts oscillator
(C) Weinbridge oscillator
(D) R-C phase shift oscillator

Ans. (B)
We have two capacitors in the tank circuit, which serve as a simple ac voltage
divider.

Q.53 The function of a bleeder resistor in a power supply is
(A) the same as that of load resistor
(B) to ensure a minimum current drain in the circuit
(C) to increase the output dc
voltage
(D) to increase the output current

Ans.
(B)

Q.54 In a bistable multivibrator circuit, commutating capacitor is used
(A) to increase the base storage charge
(B) to provide ac coupling
(C) to increase the speed of
response
(D) to provide the speed of oscillations

Ans. (C)
The commutating capacitor is used for the speedy transition of the state of the
bistable.

Q.55 n-type silicon is obtained by
(A) Doping with tetravalent element
(B) Doping with pentavalent element
(C) Doping with trivalent element
(D) Doping with a mixture of trivalent and
tetravalent element

Ans: (B)
The pentavalent atom provides an excess electron while the other four form
the covalent bond with the neighbouring atoms. This excess free electron
provides the n type conductivity.

Q.56 The forward characteristic of a diode has a slope of approximately 50mA/V at a
desired
point. The approximate incremental resistance of the diode is
(A) 50Ω (B) 35Ω
(C) 20Ω (D) 10Ω

Ans: (C)
Resistance at any point in the forward characteristics is given by R= ΔV/ ΔI
= 1/50mA = 20Ω

Q.57 Two stages of BJT amplifiers are cascaded by RC coupling. The voltage gain of the
first
stage is 10 and that of the second stage is 20. The overall gain of the coupled
amplifier is

(A) 10x20
(B) 10+20
(C) (10+20)2
(D) (10x20)/2

Ans: (A)
The voltage gain of a multistage amplifier is equal to the product of the gains
of the individual stages.
Q.58 In the voltage range, Vp < VDS < BVDSS of an ideal JFET or MOSFET
(A) The drain current varies linearly with VDS.
(B) The drain current is constant.
(C) The drain current varies nonlinearly with
VDS.
(D) The drain current is cut off.

Ans: (B)
It is the saturation region or pinch off region, and drain current remains almost
constant at its maximum value, provided VGS is kept constant.

Q.59 In a voltage shunt negative feedback amplifier system, the input resistance Ri and the
output
resistance Ro of the basic amplifier are modified as follows:
(A) Ri is decreased and Ro increased.
(B) Both Ri and Ro are decreased.
(C) Both Ri and Ro are increased
(D) Ri is increased and Ro is decreased.

Ans: (B)
Here, a fraction of output voltage obtained by parallel sampling is applied in
parallel with the input voltage through feedback and both input and output
resistance decrease by a factor equal to (1+ βAv).

Q.60 The use of crystal in a tunable oscillator
(A) Improves frequency stability.
(B) Increases the gain of the oscillator.
(C) Helps to obtain optimum output impedance.
(D) Facilitates generation of wide range of
frequencies.

Ans: (A)
Piezoelectric crystal is used as a resonant tank circuit. The crystal is made of
quartz material and provides a high degree of frequency stability.

Q.61 The large signal bandwidth of an opamp is limited by its
(A) Loop gain (B) slew rate
(C) output impedance (D) input
frequency

Ans: (B)

Q.62 Rectification efficiency of a full wave rectifier without filter is nearly equal to

(A) 51% (B) 61%
(C) 71% (D) 81%

Ans: (D)
Efficiency of a full wave rectifier is given by
[(2Im / π) 2 x RL] / [(Im / √2) 2 x (Rf + RL)] =
81%, when Rg is zero.

Q.63 When the temperature of a doped semiconductor is increased, its conductivity
(A) decreases.
(B) increases.
(C) does not change.
(D) increases or decreases depending on whether it is p- or n-type.

Ans: B
Q.64 The main characteristics of a Darlington Amplifier are
(A) High input impedance, high output impedance and high current gain.
(B) Low input impedance, low output impedance and low voltage gain.
(C) High input impedance, low output impedance and high current gain.
(D) Low input impedance, low output impedance and high current gain.

Ans: C

Q.65 The transconductance, gm, of a JFET is computed at constant VDS, by the following:
(A) (B)
(C) (D)
Ans: A

Q.66 The feedback factor β at the frequency of oscillation of a Wien bridge oscillator is
(A) 3 (B)
(C) (D)

Ans: B

Q.67 In an amplifier with negative feedback, the bandwidth is
(A) increased by a factor of β
(B) decreased by a factor of β
(C) increased by a factor of (1+Aβ)
(D) not affected at all by the feedback
where A = gain of the basic amplifier and β = feedback factor

Ans: C

Q.68 The ‘slew rate’ of an operational amplifier indicates
(A) how fast its output current can change
(B) how fast its output impedance can change
(C) how fast its output power can change
(D) how fast its output voltage can change
when a step input signal is given.

Ans: D

Q.69 In a clamping circuit, the peak-to peak voltage of the waveform being clamped is
(A) affected by the clamping
(B) not affected by the clamping
(C) determined by the clamping voltage value
(D) determined by the ratio of rms voltage of the waveform and the clamping voltage
Ans: B
Q.70 Regulation of a.d.c. power supply is given by
(A) product of no-load output voltage and full-load current
(B) ratio of full-load output voltage and full-load current
(C) change in output voltage from no-load to full-load
(D) change in output impedance from no-load to full-load

Ans: D

Q.71 A ‘literal’ in Boolean Algebra means
(A) a variable inn its uncomplemented form only
(B) a variable ORed with its complement
(C) a variable in its complemented form only
(D) a variable in its complemented or uncomplemented form

Ans: D

Q.72 In an unclocked R-S flip-flop made of NOR gates, the forbidden input condition is
(A) R = 0, S = 0 (B) R = 1, S = 0
(C) R = 0, S = 1 (D) R = 1, S = 1

Ans: D

Q.73 The current amplification factor in CE configuration is
(A) α (B) β + 1
(C) (D) β

Ans: D

Q.74 A zener diode
(A) Has a high forward voltage rating.
(B) Has a sharp breakdown at low reverse voltage.
(C) Is useful as an amplifier.
(D) Has a negative resistance.

Ans: B

Q.75 N-channel FETs are superior to P-channel FETs, because
(A) They have a higher input impedance.
(B) They have high switching time.
(C) They consume less power.
(D) Mobility of electrons is greater than that of holes.

Ans:

Q.76 The maximum possible collector circuit efficiency of an ideal class A power amplifier is
(A) 15% (B) 25%
(C) 50% (D) 75%

Ans: C

Q.77 Negative feedback in an amplifier
(A) Reduces the voltage gain.
(B) Increases the voltage gain.
(C) Does not affect the voltage gain.
(D) Converts the amplifier into an oscillator.

Ans: A

Q.78 For generating 1 kHz signal, the most suitable circuit is
(A) Colpitts oscillator. (B) Hartley oscillator.
(C) Tuned collector oscillator. (D) Wien bridge oscillator.

Ans: D

Q.79 Phe output stage of an op-amp is usually a
(A) (A) Complementary emitter follower.
(B) (B) Transformer coupled class B amplifier.
(C) (C ) Class A power amplifier.
(D) (D) Class B amplifier.

Ans: A

Q.80 When a sinusoidal voltage wave is fed to a Schmitt trigger, the output will be
(A) triangular wave. (B) asymmetric square wave.
(C) rectangular wave. (D) trapezoidal wave.

Ans: B

Q.81 If the peak value of the input voltage to a half wave rectifier is 28.28 volts and no filter is
use, the maximum dc voltage across the load will be
(A) . (B) 15 V.
(C) 9 V. (D) 14.14 V.

Ans: C

Q.82 The logic gate which detects equality of two bits is
(A) EX-OR (B) EX-NOR
(C) NOR (D) NAND

Ans: B

Q.83 The electron relaxation time of metal A is s, that of B is s. The ratio
of resistivity of B to resistivity of A will be
(A) 4. (B) 2.0.
(C) 0.5. (D) 0.25.

Ans: B

Q.84 The overall bandwidth of two identical voltage amplifiers connected in cascade will
(A) Remain the same as that of a single stage.
(B) Be worse than that of a single stage.
(C) Be better than that of a single stage.
(D) Be better if stage gain is low and worse if stage gain is high.

Ans: B

Q.85 Field effect transistor has
(A) large input impedance. (B) large output impedance.
(C) large power gain. (D) large votage gain.

Ans: A

Q.86 Which of the following parameters is used for distinguishing between a small signal and
a large-signal amplifier?
(A) Voltage gain (B) Frequency response
(C) Harmonic Distortion (D) Input/output impedances

Ans: D

Q.87 Which of the following parameters is used for distinguishing between a small signal and
a large-signal amplifier?
(A) Instability (B) Bandwidth
(C) Overall gain (D) Distortion

Ans: B

Q.88 If the feedback signal is returned to the input in series with the applied voltage, the input
impedance ______.
(A) decreases (B) increases
(C) does not change (D) becomes infinity

Ans: B

Q.89 Most of linear ICs are based on the two transistor differential amplifier because of its
(A) input voltage dependent linear transfer characteristic.
(B) High voltage gain.
(C) High input resistance.
(D) High CMRR

Ans: D

Q.90 The waveform of the output voltage for the circuit shown in Fig.1 (RC >> 1) is a
(A) sinusoidal wave (B) square wave
(C) series of spikes (D) triangular wave.

Ans: D

Q.91 A single phase diode bridge rectifier supplies a highly inductive load. The load current
can be assumed to be ripple free. The ac supply side current waveform will be
(A) sinusoidal (B) constant dc.
(C) square (D) triangular

Ans: C

Q.92 Which of the following Boolean rules is correct?
(A) A + 0 = 0 (B) A + 1 = 1
(C) (D)

Ans: B

Q.93 A single phase diode bridge rectifier supplies a highly inductive load. The load current
can be assumed to be ripple free. The ac supply side current waveform will be
(A) sinusoidal (B) constant dc.
(C) square (D) triangular

Ans: C

Q.94 Which of the following Boolean rules is correct?
(A) A + 0 = 0 (B) A + 1 = 1
(C) (D)

Ans: B
PART – II

NUMERICALS

Q.1 In a transformer, give the relationship between
(i) turns ratio and its primary and secondary impedances
(ii) turns ratio and primary/secondary voltage.
In a transformer-coupled amplifier, the transformer used has a turns ratio N1:N2 = 10:1.
If the source impedance is 8 KΩ what should be the value of load impedance for
maximum power transfer to the load? Also find the load voltage if the source voltage is
10 volts. (6)

Ans: p. 439 – 40

Given: ; - load side; -
amplifier side or source side.

Turns ratio and impedances:
Turns ration and voltages:
; i.e.
Load voltage = V2 ;
.

Q.2 The FET circuit given below in Fig.1, has R1=3.5MΩ, R2 = 1.5MΩ, RS = 2KΩ, RL =
20KΩ and gm = 2.5mS. Find its input impedance, output impedance and voltage
gain. (8)

Ans:

(i)
(ii)
(iii) Voltage
gain

Q.3 In an amplifier with negative feedback, the gain of the basic amplifier is 100 and it
employs a feedback factor of 0.02. If the input signal is 40mV, determine
(i) voltage gain with feedback and
(ii) value of output
voltage. (3)

Ans:
(i)
(ii)

Q.4 In the circuit shown below in Fig.2, R1=12KΩ, R2 = 5KΩ, R3 = 8KΩ, RF = 12KΩ. The
inputs are: V1 = 9V, V2 = -3V and V3 = -1V. Compute the output
voltage. (4)
Ans:

= - 12(0.75 – 0.6 – 0.125) = - 0.3 V.

Q.5 A half-wave rectifier has a load resistance of 3.5 KΩ. If the diode and secondary of the
transformer have a total resistance of 800KΩ and the ac input voltage has 240 V (peak
value), determine:
(i) peak, rms and average values of
current through load
(ii) DC power output
(iii) AC power input
(iv) rectification
efficiency (7)

Ans:

(i) Im = Vm = 240 = 55.8mA = peak current.
RL + Rf 3.5X 103 + 800
= average current.
.
(ii) DC power output = watts.

(iii) AC power input = watts.
(iv) Rectification Effect = .

Q.6 A BJT has a base current of 250 μA and emitter current of 15mA Determine the
collector current gain and β. (2)

Ans:
The current relationship in a transistor is given by
i.e.
Given:
IE = 15 mA

And .

Q.7 In the circuit shown in Fig.1, [IDSS] = 4mA, Vp = 4V. Find the quiescent values of 1D,
VGS and VDS of the FET. (6)
Fig.1
Ans:

The potential divider bias circuit can be replaced by Thevenin equivalent as shown,
where

Applying Kirchoff’s Voltage law to gate–source circuit gives as
there is no gate current flow.
Hence

Given, IDSS = 4 mA and VP = 4 V. substituting these values in the equation for IP

Forming the quadratic equation in VGS.

Solving, VGS = 3 V(Solution VGS = 4V is not
realistic).
Solving for ID, ID = (1 – ¾) = 0.25 mA
Hence, VDS = 30 – 0.25(18 + 4) = 24.5 Volts.

Q.8 In the transformer coupled class A amplifier shown in Fig.2 below, the transistor has
hFE = β = 40 and hie = 25Ω. Assume that the transformer is ideal and that and
also . Determine values of R1 and R2 to obtain quiescent current ICQ = 100mA.
If the collector current swing , find the peak values of load current and load
voltage. Transformer turns ratio is primary 1:6 secondary. (10)

Ans:
The equivalent circuit replacing R1, R2 as part of thevenin source is shown

……(1) ………(2)

Applying KVL around base-emitter circuit,

i.e. …….(3)

Any value of RB by which is acceptable. Hence, choosing a reasonable
value of 2.2K for RB, volts.
Use equations (1) and (2) to find R1 and R2
From (1)
i.e. ……..(4)

substituting the value of R1 in equation (2)

….(5)
simplifying, ………(6)
From (4) and (6), we get
………(7)
using equation (6),
using equation (7),

The load Rac at the collector leg of the transistor is reflected load of R L as per the turns
ratio (a) of the transformer.
i.e.
As ic swings ± 80 mA either side of I CQ = 100 mA on the Rac load line, and VCEQ =
12V (DC load line being almost vertical)

= 12 + 5.55 = 17.55 Volts.
Hence, Maximum Load voltage(secondary):

Hence, Maximum Load current:
.

Q.9 A negative feedback of β = 2.5 x 10-3 is applied to an amplifier of open loop gain 1000.
Calculate the change in overall gain of the feedback amplifier if the gain of the internal
amplifier is reduce by 20%. (4)

Ans:
If A is the gain of the basic amplifier, the overall gain A f of the amplifier with
negative f.b. is
given A = 1000 and β = 2.5 x 10-3,
When A is reduced by 20%, the new A, say An = 1000 – 0.2 x 103 = 800
The new voltage gain with f.b. is
.

Q.10 A full wave rectifier is fed with a voltage, 50 sin 100 πt. Its load resistance is 400Ω. The
diodes used in the rectifier have an average forward resistance of 30Ω. Compute the
(i) average and rms values of load current,
(ii) ripple factor and
(iii) efficiency of
rectification. (6)

Ans:
The maximum value of load current
; given: Vmax = 50volts; RL = 400Ω, RF = 30 Ω

Thus

Average current Iavg = 2 Imax for a FWR
π
i.e. Iavg = 2 X 0.1163 = 0.074A or 74 mA = Idc
λ
The r.m.s value of load current is

Ripple factor
Efficiency of rectification in a FWR is given by

i.e. or 75.5%.

Q.11 For the circuit shown in Fig.2, find thee
maximum and minimum values of zener diode
current. (8)
Fig.2

Ans: 9mA, 1.0mA.

Q.12 The parameters of the transistor in the circuit
shown in Fig.3 are Find
(i) midband gain
(ii) the value of Cb necessary to give a lower 3 dB frequency of 20Hz
(iii) the value of Cb necessary to ensure less than 10% tilt for a 100 Hz square wave
input.

(8)
Fig.3

Ans:
(i) 32.26 (ii) 2.567 Mf (iii) 16.13 Mf

Q.13 For the circuit shown in Fig.4, determine
voltage gain, input impedance, output impedance, common-mode gain and CMRR
if , , and transistors Q1 and Q2 are identical
with . Determine output voltage when and when
. (8)
Fig.4
Ans:
A = 150, Zin = 0.66MΩ, Zout = 1MΩ
Acm = 0.5, CMRR = 300
Vout = 7.5V and 0.15V

Q.14 A class B push-pull amplifier is supplied
with . The minimum voltage reached by the collector due to signal swing
is . The dissipation in both the transistors totals 30 W. What is the
conversion efficiency of the amplifier? (7)

Ans:
DC supply voltage, Vcc = 40v
Vmin = 8v, Pd = 30w.
As Pd = Pin(dc) – Pout(ac)

Conversion Efficiency,

Q.15 The input to an op-amp differentiator circuit
is a sinusoidal voltage of peak value and frequency of 2 kHz. If the values of
differentiating components are given as R = 40 k and C = , determine the
output voltage. (4)

Ans:

Scale factor = CR =

Q.16 Draw the circuit of a monostable
multivibrator using two transistors. Use the following data in your circuit:
, , B , for both the transistors. The resistor
and capacitor connected to the base of have values and C = 0.1
respectively. Determine the monostable pulse
width. (8)

Ans:
, Input pulse width,

T = 1.4 714 m sec.
Monostable Multivibrator Circuit
Q.17

For
the series
regulator
given
below,
,
, the
transistor
,
=1.2
K ,
=10V
and
. Calculate
(i) output
voltage
(ii) load
current
(iii) the
base
current in
the
transistor
(iv) zener
current.

(8)

Ans:

Q.18 Find the values of collector and emitter currents in a transistor having I CBO=3μA,
and αdc=0.98 when its base current is
60μA. (6)

Ans:
=
We know that

Emitter current,
=
.

Q.19 The h-parameters of the transistor in the
amplifier circuit shown below are: hie=2.2 KΩ , hfe=52, hoe= and hre is
negligible. The output load resistor dissipates a signal power of 9 mW. Determine the
power gain of the amplifier using its equivalent circuit. The reactances of the
capacitors may be neglected. (8)

+ Vcc

Ans:

Input impedance to E,

Power drawn from the source, .
Base current,
=

Output impedance,

AC-load resistance,

Output voltage,

E = 0.2715
Power gain, Ap =

.

Q.20 The collector voltage of a Class B push pull
amplifier with VCC=40 Volts swings down to a minimum of 4 volts. The total power
dissipation in both the transistors is 36 watts. Compute the total dc power input and
conversion efficiency of the amplifier. (7)

Ans:

=
36 =
36 =

=

Q.21 The transistor in the feedback circuit shown below has β=200. Determine
(i) feedback factor, (ii) feedback ratio, (iii) voltage gain without feedback and (iv)
voltage gain with feedback in the circuit. In the transistor, under the conditions of
operation, VBE may be assumed to be negligible. (6)

Ans:
, , ,

AC Emitter resistance,

Voltage gain without feedback,

A = 1008.16
Feedback ratio

Feedback factor =
Feedback factor = 48.0076
Voltage gain with feedback,

Q.22 In the differential amplifier circuit shown
below, the transistors have identical characteristics and their β=100.Determine the (i)
output voltage (ii) the base currents and (iii) the base voltages taking into account the
effect of the RB and VBE. Take VBE=0.7 Volts. (8)

Ans:
Tail current,

The collector current in transistor Q2 is half thus tail current (i.e. 0.75mA) because
each transistor gets half the tail current.

Tail current

And Tail current,

And output voltage,

=

If the results obtained are compared, we find that the results obtained improve with
each refinement, but the improvement is not significant.
The ideal tail current is 1.41mA

Q.23 Design a series voltage regulator to supply
1A to a load at a constant voltage of 9V. The supply voltage to regulator is 15V±10%.
The minimum zener current is 12mA. For the transistor to be used, assume V BE=0.6V
and β=50. (7)

Ans:

Voltage drop in resistor
Current through resistor R,

.

Q.24 Obtain the minterms of the function
ƒ(A,B,C) =
and draw the K-map of the
function. (4)

Ans:

=
=

Q.25 A load line intersects the forward V-I
characteristic of a silicon diode at Q, where the slope of the curve is 40mA/V.
Calculate the diode resistance at the point Q. (4)

Ans:
DC or static resistance,

.

VCC=

Q.26 The power amplifier shown below is operated
in class A, with a base current drive of 8.5mA peak. Calculate the input dc power, the
power dissipated in the transistor, the signal power delivered to the load and the
overall efficiency of the amplifier, if transistor β=30 and
VBE=0.7V. (8)

Ans:

Now dc – load line is drawn joining points (20v, 0) and (0, 1.25A)
For operating point Q,

.

= 0.5202 w.
Power delivered to the transistor,

= 20(0.579) – (0.579)2.16
= 6.216w
Power lost in transistor =
= 6.216 – 0.5202
= 5.6958
Collector Efficiency,
=
= 8.368 %.
Power rating of transistor = Zero-signal power dissipation
=
=
= 6.216w.

Q.27 Find the period of the output pulse in the circuit shown
below: (4)
Ans:
TIMERS

The pulse width

= .

Q.28 Analyze half-wave and full-wave rectifier
circuits (without filter) to deduce the values of rectification efficiency assuming ideal
diodes. (8)

Ans:
Rectification efficiency of half-wave rectifier, which is defined as the ratio of dc-
output power to the ac-input power, is given as

= .
Now, .
Pac = Power dissipated in diode junction + Power dissipated in load resistance RL
=
=

i.e. 40.6 % if RF is neglected.

Full-wave rectifier:

Rectification efficiency,

if RF is neglected.

Q.29 An intrinsic silicon bar is 4mm long and has a rectangular cross section 60x100
(m) 2. At 300K, find the electric field intensity in the bar and voltage across the bar
when a steady state current of 1A is measured. (Resistivity of intrinsic silicon at
300K is 2.3 x
3
10 m (7)

Ans:
Length=4mm
A=60 x 100 (m) 2
Current I =1A
Resistivity r = 2.3 x 103 m
J = σ E
E = J / σ = (I/A) (1/σ) = (I/A) r
E = (1 x 10-6/ (60 x 10-6 x 100 x 10-6))x 2.3 x103
= 383.33 x 103 V/m
V = EL = 383.33 x 103 x 4mm =1.53 x 103 V

Q.30 The resistivity of doped silicon material is 9 x 10-3ohm-m. The Hall co-efficient is
3.6 x 10-4m3 columb-1. Assuming single carrier conduction, find the mobility and
density of charge carrier (e = 1.6 x 10-
19
coulomb) (7)

Ans:
RH = 3.6x10-4 m3/columb, ρ = 9x10-3 ohm-m
Mobility = μn = σ RH = (1/ρ)RH = (1/9x10-3)x 3.6x10-4 = 400 cm2/V-s

Density of charge carriers = σμ

= (1/9x10-3) 400 = 44.44m coulomb

Q.31 A single tuned amplifier with capacitive coupling consists tuned circuit having R=10,
L=20mH and C=0.05 F. Determine the (i) Resonant frequency (ii) Q-factor of the tank
circuit (iii) Bandwidth of the
amplifier. (7)

Ans:
(i) Reasonant frequency: fr = 1 / (2 √LC) = 1 / (2 √ 20x10-
3 -6
x0.05x10 ) = 5032 Hz
(ii) Q-factor of the tank circuit: Q = XL / R = 2 frL / R.
XL=2 frL / = (2 x 5032 x 20x10-3)/10=63.23
Q = 63.23 / 10 =6.32
(iii) Band width of the amplifier: As Q = fr / BW
6.32 = 5032 / BW
BW = 769.20Hz

Q.32 Calculate the output voltage ‘V0’ for the following non inverting op-amp summer,
with V1 =2V and V2 = -1V (7)

Ans:
VO = ([R2V1 + R1V2] / [R1 + R2] )* ([R + Rf] / R)
If in the summer circuit the value of resistance are selected as R1 = R2 = R and
Rf = 2R . Then
VO = - [(2R) V1/R + (2R) V2/R]
= - [2(V1 + V2)]
= - [2(2 -1) ] = -2 V

Q.33 The current flowing through a certain P-N junction at room temperature when reverse
biased is 0.15μA. Given that volt-equivalent of temperature, V T is 26mV, and the bias
voltage being very large in comparison to VT, determine the current flowing through the
diode when the applied voltage is
0.12V. (7)

Ans:
The diode current is given by
I = Io (e-(Vp/ηVT)- 1)
For large reverse bias, the diode current
I = Io = 0.15 x 10-6A.
Given V=0.12V, VT = 0.026 V, assuming Si diode, i.e.,η = 2
I = 0.15 x 10-6 (e (0.12/ (2 x 0.026)) - 1)
= 1.36 μA

Q.34 In a transistor amplifier, change of 0.025V in signal voltage causes the base current to
change by 15μA and collector current by 1.2 mA. If collector and load resistances are of
6kΩ and 12kΩ, determine
i) input resistance (ii) current gain
iii) ac load (iv) voltage gain
v) power
gain (7)

Ans:
i) Input resistance = change in input voltage / change in input current = 0.025/15 x 10 -6 =
1.67kΩ
ii) Current gain = β = change in output current / change in input current = 1.2mA/15 x 10 -
6
= 80
iii) AC load = Rc || RL = 6k x 12k/(6k+12k) = 4kΩ
iv) Voltage gain: output voltage = 1.2 x 10-3 x 4 x 103 = 4.8V = Vo
input voltage = 0.025V = Vi
Voltage Gain = Vo / Vi = 4.8 / 0.025 =192
v) Power gain = voltage gain x current gain = 192 x 80 = 15360

Q.35 What is a load line and how is it used in the calculation of current and voltage gains for
a single stage
amplifier? (7)

Ans:
In a transistor, the collector current IC depends on base current IB. The variation of IC for
a specific load RC as a function of input voltage is along a straight line. This line for a
fixed load is called as dc load line. The output characteristic of a CE amplifier is plotted
in the Fig. 13a. Consider the following specifications of the CE amplifier.

Fig. 13a
IBQ = 40μA
ICQ=8mA, VCEQ = 6V
VS = Vm sinωt
The amplitude Vm is chosen to provide a signal component of base current
Ib = Ibm sinωt
Where Ibm = 20μA
Total instantaneous base current iB is the superposition of the dc level and the signal
current.
Therefore iB = IBQ + Ib = 40 + 20 sinωt μA
From the figure, we see that variation in I B causes both IC and VCE to vary sinusoidally
about their quiescent levels. These quantities are expressed as
iC = ICQ+ iC = ICQ + Icm sinωt
vCE = VCEQ + vce = VCEQ + Vcm sinωt V
From figure 3a, Icm = 4mA and Vcm= 2V

Q.36 The transconductance of a FET used in an amplifier circuit is 4000 micro-siemens. The
load resistance is 15kΩ and drain circuit resistance is 10 MΩ. Calculate the voltage gain
of the amplifier circuit .

Ans:
Given: gm = 4000, RL = 15kΩ, rd = 10MΩ (7)
Vo = -gm x Vgs (rd || RL)
Vo / Vin = -(gm x Vgs (rd || RL)) / Vin
But Vgs = Vin
Therefore voltage gain Vo / Vin = -(gm (rd || RL))
Vo / Vin = 4000x10-6 x ( ( 106x15x103) / (106 + 15x103 ) )
= (60x106) / (103(103 + 1)
≈ 60

Q.37 An output waveform displayed on an oscilloscope provided the following measured
values
i) VCE min=1.2V, VCE max=22V, VCEQ=10V
ii) VCE min=2V, VCE max=18V, VCEQ=10V
Determine the percent second harmonic distortion in each case. (14)

Ans:
D2 = (|B2| / |B1|) x 100%
i) B2 = (Imax + I min – 2IcQ) / 4
= (VCE max + VCE min – 2VCEQ) / 4
= (22+1.2-20) / 4 = 3.2 / 4 = 0.8
B1 = (I max- Imin) / 2 = (VCE max – VCE min) / 2 = (22-1.2) / 2 = 10.4
D2 = (0.8 / 10.4)x100 = 7.69%
ii) B2 = (2+18-20) / 4 = 0
B1 = (18-2) / 2 = 8
D2 = 2.5/8 x 100 = 0%

Q.38 A sample of pure silicon has electrical resistivity of 3000Ωm. The free carrier density in
it is 1.1x1016/m3. If the electron mobility is three times that of hole mobility, find
electron mobility and hole mobility. The electronic charge is equal to 1.6x10 -
19
coulomb. (6)
Ans:
For pure Silicon, ni = n = p = 1.1x1016/ m3, and n= 3p
 = ni (n + p) e = 1.1x1016 (p + 3p) 1.6x10–19= 7.04 x 10-3 p
= (3000 m)-1
Thus px7.04x10-3 = 1/3x10-3
i.e., p = .047 m2 V-1 S-1 and n = 3 p =0.141 m2 V-1 S-1

Q.39 Explain ‘Zener breakdown’. The zener diode in the circuit shown below regulates at
50V, over a range of diode currents from 5 to 40mA. The supply voltage V = 150V.
Compute the value of R to allow voltage regulation from a zero load current to a
maximum load current Imax. What is
Imax? (8)

Ans:
Zener break down takes place in diodes having heavily doped p and n regions with
essentially narrow depletion region. Considerable reverse bias gives rise to intense
electric field in the narrow depletion region causing breakdown of covalent bonds and so
creating a number of electron-hole pairs which substantially add to the reverse current
which may sustain at a constant voltage across the junction. This breakdown is
reversible.

Problem:
For IL = 0, VL= 50 volts and
Iz = Is = (150 – 50) / R  40 mA
Hence R  100/40 K, i.e 2.5 K
For IL = Imax, Iz  5mA
But for R = 2.5 K, Is = 40 mA.
Hence Imax = 40 – 5 = 35 mA

Q.40 Draw a figure to show the output V-I characteristic curves of a BJT in
CE configuration. Indicate thereon, the saturation, active and cut off regions. Explain
how, using these characteristics, one can determine the value of h fe or
βF. (6)
Ans:
Fig. 18b

Fig. 18b. shows the characteristics of BJT in CE configuration. To find hfe, draw a
constant VCE line (vertical) going through desired Q point. Choose constant IB lines
suitably, which cut the constant Vce line at X and Y.
hfe = ΔIC/ ΔIB. From fig hfe = (IC2-IC1) / (IB4-IB2)
= (6-2) mA / (60-20)  =100.

Q.41 Draw a small signal h-parameter equivalent circuit for the CE amplifier shown
in fig below.

Find an expression for voltage gain of the amplifier.Compute the value of voltage gain,
if RC = RL = 800Ω, R1 = 1.5kΩ, R2 = 3kΩ, hre≈ 0, hoe = 100μS, hfe = 90 and hie =
150Ω. (9)

Ans:
Fig. 19 shows the small signal h-parameter model for CE amplifier
Fig.19

Voltage gain of amplifier is Av = VL / Vi
Rb = R1R2 / (R1 + R2) in the equivalent circuit.
By current division in output circuit,
Rb = (R1R2) / (R1+R2) = (1.5x103x3x103) / (1.5+3)103 = 1kΩ

Av = (-90x800x800) / [150(800+800+100x10-6x800x800) = -230.7

Q.42 The circuit of a common source FET amplifier is shown in the figure below. Find
expressions for voltage gain Av and current gain Ai for the circuit in mid frequency
region where Rs is bypassed by Cs. Find also the input resistance Rin for the amplifier. If
RD = 3kΩ, RG = 500kΩ, μ = 60, rds = 30kΩ, compute the value of Av, Ai, and
Rin. (8)

Ans:
Using voltage source model of the FET, the equivalent circuit is as in Fig.
20a
Fig. 20 a

Vo = (-RDμVgs) / (RD+rds)
Vgs = Vi
Av = Vo / Vi = (-μRD) / (RD+rds)
id = (μVgs) / (rds+RD)
Vgs = iiRG
Av = (-60x3x103) / (3x103+30x103) = -5.45
Ai = id/ii ; i.e Ai = μRG / (RD+rds) = [60x500x103] / [30x103+3x103] = 909
It is obvious that Rin = RG = 500kΩ

Q.43 State Barkhausen criterion for sustained oscillations in a sinusoidal oscillator. The
capacitance values of the two capacitors C1 and C2 of the resonant circuit of a colpitt
oscillator are C1 = 20pF and C2 = 70pF.The inductor has a value of 22μH. What is the
operating frequency of
oscillator? (5)

Ans:
Consider a basic inverting amplifier with an open loop gain ‘A’. With feedback network
attenuation factor ‘ß’ less than unity. The basic amplifier produces a phase shift of
180o between input and output. The feedback network must introduce 180 o phase shift.
This ensures positive feedback.
Barkhausen criterion states that for sustained oscillation,
1. The total phase shift around the loop, as the signal proceeds from input through the
amplifier, feedback network and back to input again, is precisely 0o or 360o.
2. The magnitude of the product of the open loop gain of the amplifier, ‘A’ and the
feedback factor ‘ß’ is unity, i.e. |Aß| = 1.
Operating frequency of Colpitts oscillator is given by
f = 1 / (2π√ LCeq)
Where Ceq = (C1C2) / (C1 + C2)
= (20 x 70) / (20 + 70) = 15.56pF.
f = 1 / {2 x π √ 22 x 10-6 x 15.56 x 10-9} = 272.02 KHz

Q.44 Suggest modification in the given circuit of Opamp to make it (i) inverting (ii)
non inverting. (7)

Ans:
Fig 24 a (i) shows an inverting amplifier. For an inverting amplifier, the input is to be
applied to the inverting terminal. Therefore point P2 is connected to the signal to be
amplified.
Fig 24 a (i) Fig 24 a (ii)

Fig 24 a (ii) shows a non-inverting amplifier. For a non-inverting amplifier, the input is
to be applied to the non-inverting terminal. Therefore point P1 is connected to the source.

Q.45 In the circuit of Q44, if input offset voltage is 0,
(i) Find the output voltage Vo due to input bias current, when IB=100nA (3)
(ii) How can, the effect of bias current be eliminated so that output voltage
is zero? (4)

Ans:
(i) When the voltage gain of op-amp is very large, no current flows into the op-amp.
Therefore IB flows into R2
Vo = IB x R2 = 100 x 10-9 x 106 =100 mV
(ii) If Vo = 0, then R1 || R2.

Let Rp=R1 || R2
Then voltage from inverting terminal to ground is
VI = -IB2 x Rp
Let R1 = Rp = (R1 x R2) / (R1 + R2) = 90.9kΩ
Add resistor R1 between non-inverting terminal and ground
Choose the value of R1 = 90.9kΩ to make the output voltage as zero.
Since, VI –VN = 0 or VI = VN
where VI : Voltage at the inverting terminal w.r.t. ground
and VN : Voltage at the non-inverting terminal w.r.t. ground
Hence, -IB2 x Rp = -IB1 x R1
For IB1 = IB2

Q.46 A differential amplifier has inputs Vs1=10mV, Vs2 = 9mV. It has a differential mode gain
of 60 dB and CMRR is 80 dB. Find the percentage error in the output voltage and error
voltage. Derive the formulae
used. (14)

Ans:
In an ideal differential amplifier output Vo is given by
Vo = Ad (V1-V2)
Ad = gain of differential amplifier

But in practical differential amplifiers, the output depends on difference signal V d as well
as on common mode signal VC.
Vd = V1 – V2 ---------- 1
VC = (V1 + V2) / 2 --------2
Therefore output of above linear active device can be given as
Vo = A1V1 + A2V2

Where A1(A2) is the voltage amplification factor from input 1(2) to output under the
condition that input 2(1) is grounded.
Therefore from 1 and 2
V1 = Vc + 0.5Vd and V2=Vc-0.5Vd
Vo = AdVd + AcVc
Where Ad = 0.5(A1-A2) and Ac = 0.5(A1+A2)
the voltage gain of difference signal is Ad and voltage gain of common mode signal is Ac.
Common mode rejection ratio = ρ = |A d/Ac|. The equation for output voltage can be
written as
Vo = AdVd (1+ (Ad/Ac) (Vc/Vd))
Vo = AdVd (1+ (1 / ρ) (Vc/Vd))
Vs1=10mV = V1 , Vs2=9mV = V2
Ad=60dB, CMRR=80dB
Vd = V1-V2=10mV-9mV=1mV
Ad = 60dB = 20log10 Ad, since Ad =1000
Vc = (V1+V2)/2 = (10+9) / 2 = 9.5mV
CMRR = Ad / Ac
10³ = 1000 / Ac
Ac = 0.1
Vo = AdVd + AcVc = 1000 x 10-3 + 0.1 x 9.5 x 10-6
= 1.00095 V

Q.47 Prove the following postulate of Boolean algebra using truth tables
x + y + z = (x + y).(x + z ) (3)

Ans:
The truth table below demonstrates the equality (x + y + z) = (x + y) (x + z)

X y z (x+y) (x+z (x+y) x+y+z
) (x+z)
0 0 0 0 0 0 0
0 0 1 0 1 0 0
0 1 0 1 0 0 0
0 1 1 1 1 1 1
1 0 0 1 1 1 1
1 0 1 1 1 1 1
1 1 0 1 1 1 1
1 1 1 1 1 1 1

Q.48 Simplify the following Boolean function using K-map:
_ _ _
f(a,b,c) = a c + a b + a b c + b c Give the logic implementation of the simplified
function in SOP form using suitable gates. (6)

Ans:
a
b

c

_
The simplified function by implementation of K-map is f (a,b,c) = a b + c . Assuming
the availability of complements, the logic implementation is as in Fig. 40b.

Fig. 40b

PART – III

DESCRIPTIVES

Q.1 A triangular wave shown in fig(1) is applied to the circuit in fig(2). Explain the
working of the circuit. Sketch the output waveform.

Vin

25v

t

-25v

Fig(1)

R
RL
Vin D1 D2
Vout

12v 8v

Fig (2)

Ans:
Vin

+12v

t

-12v

During the positive half-cycle of the input triangular voltage, the diode D 1 remain
forward biased as long as input voltage exceeds battery voltage +12v and diode
D2 remains reverse biased and acts as open circuit. Thus up to +12v of the applied signal
there would be output voltage across the output terminals and the triangular signal will
be clipped off above 12v level.
During negative half-cycle of the input signal voltage, diode D1 remains reverse-biased
while D2 remains forward-biased as long as input signal voltage exceeds the battery
voltage -8v in magnitude.

Q.2 Define ‘diffusion capacitance’ of a pn junction diode. Obtain an expression for the
same. Why is the diffusion capacitance negligible for a reverse biased
diode? (9)

Ans:
When a P-N junction is forward biased, a capacitance which is much larger than the
transition capacitance, comes into play. This type of capacitance is called the
diffusion capacitance, CD.
Diffusion capacitance is given by the equation, where dQ represents the

change in number of minority carriers stored outside the depletion region when a
change in voltage across diode, dV, is applied.

If is the mean life-time of charge carriers, then a flow of charge Q yields a diode
current I given as

We know that

So,

So diffusion capacitance

For a forward bias,

Thus the diffusion capacitance is directly proportional to the forward current through
the diode.
CD: Diffusion capacitance.
CT: Transition capacitance.

15

10

5
CD
CT

In a reverse biased diode both CD and CT are present but CT >> CD. Hence in a reverse
biased diode CD is neglected and only CT is considered.

Q.3 Draw the circuit of h-parameter equivalent of a CE amplifier with un by-passed
emitter resistor. Derive an expression for (i) its input impedance and (ii) voltage gain,
using the equivalent circuit. (10)

Ans:
VS

Ie

Ib

CE – amplifier AC – Equivalent Circuit with an un-bypassed Emitter Resistor
(RE).

CE – Amplifier n – parameter Equivalent circuit with RE.

Input Impedance:
Zin (base) or Zb = hie
With an un-bypassed emitter register RE in the circuit,

= .
But .

RL )

Voltage Gain:

The minus sign indicates that output voltage Vout is 1800 out of phase with input
voltage Vin.
With an un-bypassed RE in the circuit,

Usually ,
RL )

Q.4 What is a ‘multistage amplifier’? Give the requirements to be fulfilled for an ideal
coupling network. (6)

Ans:
The voltage amplification or power gain or frequency response obtained with a single
stage of amplification is usually not sufficient to meet the needs of either a composite
electronic circuit or load device. Hence, several amplifier stages are usually employed
to achieve greater voltage or current amplification or both. A transistor circuit
containing more than one stage of amplification is known as a MULTI-STAGE
amplifier.
In a multistage amplifier, the output of first-stage is combined to next stage through a
coupling device.
For an ideal coupling network the following requirements should be
fulfilled.
1. It should not disturb the dc-bias conditions of the amplifiers being coupled.
2. The coupling network should transfer ac signal waveform from one amplifier
to the next amplifier without any distortion.
3. Although some voltage loss of signal cannot be avoided in the coupling
network but this loss should be minimum, just negligible.
4. The coupling network should offer equal impedance to the various
frequencies of signal wave.

Q.5 Draw a neat sketch to illustrate the structure of a N-channel E-MOSFET. Explain its
operation. (9)

Ans:
N-Channel E-MOSFET Structure
Operation of N-Channel E-MOSFET

Operation:
It does not conduct when VGS = 0. In enhancement mosfet drain (ID) current flows
only when VGS exceeds gate-to-source threshold voltage.
When the gate is made positive with respect to the source and the substrate, negative
change carriers within the substrate are attracted to the +ve gate and accumulate close
to the surface of the substrate. As the gate voltage increased, more and more electrons
accumulate under the gate, these accumulated electrons i.e., minority charge carriers
make N-type channel stretching from drain to source.
Now a drain current starts flowing. The strength of the drain current depends upon the
channel resistance which, in turn, depends on the number of charge carriers attracted
to the positive gate. Thus drain current is controlled by the gate potential.

Q.6 Show that in an amplifier, the gain reduces if negative feedback is
used. (6)

Ans:
When the feedback voltage (or current) is applied to weaken the input signal, it is
called negative feedback
β

For an open-loop amplifier,
Voltage again,
Let a fraction (say β) of the output voltage V out, be supplied back to the input and A be
the open-loop gain. Now
For + ve feedback case
And
For negative feedback case,
Actual input voltage to amplifier,

Q.7 In a voltage series feedback amplifier, show that
a. the input impedance increases with negative feedback.
b. the output impedance decreases due to negative
feedback. (10)

Ans:
The input impedance can be determined as follows:

=
Or

The effect of negative feedback on the output impedance of an amplifier is explained
below.

Or
Or

Thus, series voltage negative feedback reduces the output impedance of an amplifier
by a factor (1 + βA).

Q.8 List the advantages of a crystal oscillator. (4)

` Ans:
Advantages:
1. It is very simple circuit as it does not need any tank circuit rather than crystal
itself.
2. Different oscillation frequencies can be had by simply replacing one crystal
with another.
3. The Q-factor, which is a measure of the quality of resonance circuit of a
crystal, is very high.
4. Most crystals will maintain frequency drift to within a few cycles at 250c.

Q.9 Explain how the timer IC 555 can be operated as an astable multivibrator, using
timing diagrams. (8)

Ans:
c=
0.01µF

The Timer -555 As An Astable Multivibrator
An astable multivibrator, often called a free-running multivibrator, is a rectangular-

wave generating circuit. The timing during which the output is either high or low is
determined by the externally connected two resistors and a capacitor.
Internal Circuitary With External Connections
When Q is low, or output Vout is high, the
discharging transistor is cut-off and capacitor C begins charging towards V cc through
resistances RA and RB. Because of this, the charging time constant is (RA + RB)C.
Eventually, the threshold voltage exceeds + , comparator 1 has a high output

and triggers the flip-flop so that its Q is high and the timer output is low. With Q high,
the discharge transistor saturates and pin-7 grounds so that the capacitor C discharges
through resistance RB, trigger voltage at inverting input of comparator-2 decreases.
When it drops below . The output of comparator 2 goes high and this reset the
flip-flop so that Q is low and the timer output is high.

Q.10 Establish from first principles, the continuity
equation, valid for transport of carriers in a semi-
conductor. (10)

Ans:
The continuity equation states a condition of

a dynamic equilibrium for the concentration of mobile carriers in any elementary
volume of the semiconductor.
The carrier concentration in the body of semiconductor is a function of both time and
distance. The differential equation governing this functional relationship, called the
continuity equation, is based upon the fact that charge can be neither created nor
destroyed.
Consider an infinitesimal element of volume of area a, and length dx, as shown in fig,
within which the average hole is p. If τn is the mean lifetime of holes then P/τn equals
the holes per second lost by recombination per unit volume. If ‘e’ is the electronic
charge, then, because of recombination, the number of coulombs per second decreases
within the volume and decrease within the volume = ------(1)

If ‘g’ is the thermal rate of generation of electron-hole pairs per unit volume, the
number of coulombs per second increases within the volume and increase within the
volume = e.a.dx.g ------(2)
In general, the current varies with distance within the semiconductor. If the current
entering the volume at x is In and leaving at x + dx is
Decrease within the volume = dIn. -------(3)
Because of three effects enumerated above, the hole concentration must change with
time, and the total number of coulombs per second increases within the volume.
Increase within the volume =

------(4)
Since the charge must be conserved, so
-------(5)
The hole current In is the sum of drift current and diffusion current so,
------(6)
If the semiconductor is in thermal equilibrium with its surroundings and is subjected
to no applied fields, the hole density will attain a constant volume Po.
Under these conditions .
So from the equation (5), we have ------(7)

Combining equations (5), (6) and (7) we have the equation of conservation of charge,
called the continuity equation,

Q.11 What are the important characteristics of a
cascade amplifier? Write the circuit of cascade amplifier and determine an expression
for its voltage gain in terms of its circuit
parameters.
(8)
Ans:
Important characteristics:
1. High input impedance
2. Low voltage gain
3. Input Miller capacitance is at a minimum with the common base stage
providing good high frequency operation.

= .
With a stage gain of only 1, no Miller effect occurs at transistor Q 1. Voltage gain
of stage-2,

Over-all voltage gain, .

Q.12 Write a neat sketch to shown the construction
of a depletion-enhancement MOSFET and explain its operation in both the
modes. (9)

Ans
N-channel DE- MOSFET Structure

DE-MOSFET can be operated with either a positive or a negative gate. When gate is
positive with respect to the source it operates in the enhancement. When the gate is
negative with respect to the source, it operates in depletion-mode.
When the gate is made negative w.r.t the substrate, the gate repels some of the
negative charge carriers out-of the N-channel. This creates a depletion region in the
channel and therefore, increases the channel resistance and reduces the drain current.
The more negative the gate, the less the drain current.

Q.13 Draw the circuit of Hartley oscillator and
derive an expression for its frequency of
oscillation. (10)

Ans:

The Hartley oscillator widely used as a local oscillator in radio receivers.
--------(1)
Here , and

Substituting these values in equation (1), we get

Equating imaginary parts of above equation to zero we get,
While
Or

Or

Q.14 Write the circuit of current mirror used in a op-amp design and explain its
operation. (8)

Ans:
Current Mirror Circuit

In the design of op-amps, current strategies are used that are not practical in discrete
amplifiers. The new strategies are prompted by the fact that resistors utilize a great
deal of ‘real-estate’, and precise matching of active devices is very practical since
they share same piece of silicon. One such approach is the use of the current mirrors
to bias differential pairs. The current Ix, set by transistor Q1 and resistor Rxis mirrored
in the current I through the transistor Q2.
and .

Since

Q.15 Explain, using neat circuit diagram and waveforms, the application of timer IC555 as
monostable
multivibrator.
(9)

Ans:

Trigger Input, Output and Capacitor Voltage Wave Forms

Internal Circuitry with external connections

Operation:
Initially, when the output at pin-3 is low i.e., the circuit is in a stable state, the
transistor is on and capacitor C is shorted to ground, when a negative pulse is applied
to pin 2, the trigger input false below , the output of comparator goes high which
resets the flip-flop and consequently the transistor turns off and output at pin-3 goes
high. As the discharge transistor is cut-off, the capacitor C begins charging towards
through resistance RA with a time constant equal to RAC. When the increasing
capacitor voltage becomes slightly greater than , the output of comparator-1

goes high, which sets the flip-flop. The transistor goes to saturation, thereby
discharging the capacitor C and output of the timer goes low.

Q.16 Write the circuit diagram of a square wave
generator using an opamp and explain its
operation. (7)

Ans:
The circuit’s frequency of oscillation is dependable on the charge and discharge of a

capacitor C through feedback resistor Rf. The heart of the oscillator is an inverting op-
amp comparator.
The comparator uses positive feedback that increases the gain of the amplifier. A
fraction of the output is feedback to the non-inverting input terminal. Combination of
Rf and C acting as a low-pass R-C-Circuit is used to integrate the output voltage
Vout and the capacitor voltage Vc is applied to the inverting input terminal in place of
external signal.
where
When Vin is positive, and
When Vin is negative, .

Q.17 Distinguish between synchronous and asynchronous counters.
Show the logic diagram of a 3-bit UP-DOWN synchronous counter using suitable
flip-flops, with parallel, carry based on NAND gates and explain its operation
drawing wave diagrams. (12)

Ans:
Difference between synchronous and asynchronous counter :
1. In synchronous counters synchronized at the same time. But in the case of
asynchronous counter the output of first flip-flop is given as the clock input of
the next flip-flop.
2. In synchronous counter the output occurs after nth clock pulse if number of
bits are N. But in asynchronous counter the output is derived by previous one
that’s why n+1 step or clock pulse will be required.

Design of 3 bit UP DOWN counter:-
For M = 0, it acts as an UP counter and for M = 1 as a DOWN counter. The number
of
flip-flop required is 3. The input of the flip-flops are determined in a manner similar
to the following table.

Truth Tables
Directio Present Required FlipFlop
n State

M Q3 Q1 Q0 J0 K0 J1 K1 J2 K2
0 0 0 0 1 X 0 X 0 X
0 0 0 1 X 1 1 X 0 X
0 0 1 0 1 X X 0 0 X
0 0 1 1 X 1 X 1 1 X
0 1 0 0 1 X 0 X X 0
0 1 0 1 X 1 1 X X 0
0 1 1 0 1 X X 0 X 0
0 1 1 1 X 1 X 1 X 1
1 0 0 0 1 X 0 X 1 X
1 1 1 1 X 1 1 X X 0
1 1 1 0 1 X X 0 X 0
1 1 0 1 X 1 X 1 X 0
1 1 0 0 1 X 0 X X 1
1 0 1 1 X 1 1 X 0 X
1 0 1 0 1 X X 0 0 X
1 0 0 1 X 1 X 1 0 X

From truth table
The

Connecting the equations of all the flip-flops into NAND realization circuit

=
=

=
=
Logic diagram of 3 bit UP – DOWN Counter

Q.18 Describe how conductivity and carrier
mobility of a sample of semiconductor can be determined by subjecting it to Hall-
effect. (8)
Ans:
Y

Face 2

I d

Face 1 w

X

B

Z
When a specimen (Metal or Semiconductor) is placed in a transverse magnetic field
and a direct current is passed through it, then an electric field is induced across its
edges in the perpendicular direction of current as well as magnetic field. Thus
phenomenon is called the
Hall-Effect.
A semiconductor bar carrying a current I in the positive X-direction and placed in a
magnetic field B acting in the positive Z-direction.
In the equilibrium state the electric field intensity E due to Hall-effect must exert a
force on the charge carriers which just balances the magnetic force.
i.e. eE = Bev

where e = Magnitude of charge on electron or hole
and v = Drift-velocity.
Now electric field, or

Where d = distance between surfaces 1 and 2.
The current density is given as

Where ρ is charge density, w = width of specimen.
Now,

Hall-coefficient RH is defined by,

and conductivity,
and mobility,

Q.19 Draw the symbol and characteristics of an N-channel JFET and mark linear
region, saturation region and breakdown
region. (8)

Ans:
N-Channel JFET

JFET-drain characteristics

Q.20 Using necessary circuits and waveforms
illustrate and explain positive and negative clamping of
voltages. (12)

Ans:
Input waveform Positive Clamper Output waveform

The positive clamping circuit shifts the original signal in a vertical upward direction.
A positive clamping circuit is shown in above figure. It contains a diode D and a
capacitor C.

Input waveform Negative Clamper Output waveform

In negative clamping circuit, with the positive input, the diode D is forward biased
and capacitor C charged with the polarity shown. During the positive half-cycle of
input, the output voltage is equal to barrier potential of the diode, V o and the capacitor
is charged to (V –Vo). When the input goes negative, the diode is reverse biased and
acts as an open-circuit and thus has no effect on the capacitor voltage. R being of very
high value cannot discharge C by very much during the –ve portion of input
waveform. Thus during negative input, the output voltage being the sum of the input
voltage and the capacitor voltage is equal to –V – (V – Vo) or – (2V – Vo). Thus peak-
to-peak output being the difference of the negative and positive peak voltage levels is
equal to Vo – [- (2V – Vo)] or 2V.

Q.21 Draw the circuit of a RC-coupled amplifier.
Explain its behaviour at low, mid and high frequencies by drawing separate
equivalent circuit for each frequency region. (16)

Ans:
Two stage RC- Coupled Transistor Amplifier

1. Mid Frequency Range
Current,
So current gain,

2. High Frequency Range

So current gain,

Low frequency range:
Thevenin’s Equivalent circuit for low frequency range

So current gain,
Output-voltage,
Input-voltage,
So voltage gain

Q.22 Derive mathematical expressions to illustrate
the effects of negative feedback (i) to improve gain stabilization (ii) to reduce
distortion (iii) to modify input and output
impedances.
(8)
Ans:
Stability:- The variations in temperature, supply voltages, ageing of components or
variations in transistor parameters with replacement are some factors that affect the
gain of an amplifier and cause it to change

The gain is thus independent of internal gain of the amplifier and depends on the
passive elements such as resistors.
Diff. equation w.r.t. A,
We have
= or

Or
=

In negative feedback (1+βA) >> 1, the percentage change in gain with negative
feedback is less than the percentage change in gain without feedback. Thus negative
feedback improves the gain stability of the amplifier.
Reduction in frequency distortion:
Let the amplifier with open-loop gain A produce a distortion D in the output signal
without feedback. Now when feedback is applied, output as well distortion is
feedback to the input.
Let the gain with feedback be A f and distortion in the output D f. A part βDf of this
distortion is feedback to the input. It gets amplified by factor A and becomes βADf.
Net distortion,

Thus the distortion is reduced by a factor (1 + βA).
Input Impedance:

Output impedance:

= .
= .
Or

Thus a series voltage negative feedback reduces the output impedance of an amplifier
by a factor (1 + βA).

Q.23 Write the circuit of CLAPP oscillator and
explain its operation. What is its distinct advantage over other tuned
oscillators? (7)

Ans:

As the circulating tank current flows through C1, C2, C3 in series, the equivalent
capacitance is

In a clapp oscillator C3 is much smaller than C1 and C2. As a result, the equivalent
capacitance C is approximately equal to C3, and frequency of oscillation is given as

Advantages:
In a clap - oscillator, the transistor and stray capacitances have no effect on capacitor
C3, so the oscillation frequency is more stable and accurate.

Q.24 Explain how opamp can be used as a
(i) Differentiator (ii) Integrator
(iii) Inverting amplifier (iv)
Summer (9)

Ans:
(i) Differentiator:
Let i be the rate of change of charge i.e. dq/dt
Now charge,

(ii) Integrator:

(iii) Inverting Amplifier:
Iin

(iv) Summer
shows the summer circuit
Since Ri and Av of the opamp are ideally infinity, IB = zeroAmps and V1=V2=0V
because of virtual ground.
Therefore, Va/Ra + Vb/Rb + Vc/Rc = - (Vo/RF)
Vo = - [(RF/Ra) Va + (RF/Rb)Vb + (RF/Rc)Vc]
(v) If Ra = R b= Rc = R then Vo = (-RF/R) [Va+Vb+Vc]

i.e., output voltage is equal to the negative sum of all the input times the gain of the
circuit RF/R.

Q.25 Explain the operation of a foldback current-
limiting circuit connected to a series voltage regulator, by drawing a neat circuit
diagram. (8)

Ans:
In a simple current limiting circuit, a large amount of power dissipation in series pass
transistor Q1 while the regulator remains short-circuited. The fold-back current
limiting circuit is the solution to this problem.
In this circuit base of transistor Q3 is based by a voltage divider network consisting of
resistor R6 and R7.
--------(1)
Where

---------(2)
Now if load resistance decreases, may be due to any reason, load current I L will
increase causing voltage drop ILR5 to increase. This causes to increase and
therefore to increase. This makes transistor Q3 – ON in a stronger way. The
increased collector current of transistor Q3 flows through the resistor R3 thereby
decreasing the base voltage of transistor Q1. This results in reduction of the
conduction level of transistor Q1. Thus further increase in load current is prevented.

Q.26 Prepare the truth-table for the function
ƒ(a, b, c) =
Minimize the function using K-map. Draw
the logic diagram using gates of your choice to realize the minimized
function. (8)

Ans:
The function is f(a, b, c) =
f(a, b, c) = ac + ab
Logic realization:-

Q.27 Define mobility in a semiconductor. Does it also depend on doping levels? (3)

Ans:
In the presence of electric field in a semiconductor, the electrons move with an
average velocity called drift velocity. Mobility is the ratio of drift velocity and
electric field.
The drift velocity is given by vd=E where
E=Electric field
=constant called “mobility” of the charge carrier.
Yes, the mobility depends on the doping levels.

Q.28 What is the quantity of mobility for electrons and for holes in a silicon
semiconductor? (2)

Ans:
The typical value of mobility of electrons in a silicon semiconductor is 0.13m2/V-s and
that of holes is 0.046m2/V-s.

Q.29 A semiconductor has donor and acceptor concentrations of ND and NA, respectively.
What relationship must be used to determine the electron n and hole
p concentrations in terms of intrinsic concentration
ni? (2)

Ans:
We know that np = ni 2
For n type semiconductors: n ND
p = (ni) 2 / ND
For p type semiconductors: p NA
n = (ni) 2 / NA

Q.30 What do you understand by ‘cut-in’ voltage of a
diode? (4)

Ans:
The cut in voltage is the voltage across the diode below which current is very small(less
than 1% of rated current) in the forward biased condition only.
Fig.
3(i)

The above figure shows the V-I characteristics of diode in the forward biased region. The
current is negligibly small for V smaller than about 0.5V. This value is usually referred
to as cut in voltage.

Q.31 Sketch the volt-ampere characteristics of zener diode. Indicate the knee on the curve
and explain its significance. What happens when the current in zener decreases below
the knee current? (10)

Ans:
In the normal applications of zener diode, cathode is made positive with respect to
the anode. From the characteristics shown in fig 3 (ii), we see that for currents
greater than the knee current ( Izk ), the V-I characteristic is almost a straight line.
The zener voltage Vz is specified at nominal current Izt. As the current through the
zener deviates from Izt, voltage across changes only slightly.
The current change I is related to zener voltage change V by
V = rzI where rz = inverse of the slope of V-I curve at point Q.
Fi
g.
3(i
i)

Resistance rz is called dynamic resistance or incremental resistance of the zener diode at
operating point Q. Lower the value of r z, more constant is the zener voltage as the
current varies. From the V- I characteristics, it can be seen that r z remains low and
almost constant over a wide range of current. When the magnitude of ‘I’ decreases
below Izk, the zener ceases to operate as a voltage regulator. Because small variations in
current gives rise to large voltage variations.

Q.32 Classify the amplifiers based on frequency response. (6)

Ans:
(i) Wide band (ii) Direct coupled (iii) Tuned

amplifier

(i) Wide band amplifier: The gain remains constant over wide frequency range, but
falls off at low and high frequencies as shown in the above Fig (i) .These are also
called R-C coupled or capacitively coupled amplifiers.
(ii) Direct coupled amplifier: It is also called as dc amplifier. The amplifier maintains its
gain at low frequencies as well as for dc signal as shown in Fig (ii).
(iii)Tuned amplifier: The gain peaks around certain frequency say and falls off
drastically on both sides of this frequency. This is shown in Fig (iii).

Q.33 The low frequency response of an amplifier is characterized by the transfer
Function FL(s) = s(s+10) / [(s+100) (s+25)]. Represent its 3dB frequency
graphically.
(8)

Ans:
FL(s) = ((s+ωz1) (s+ωz2)…….) / ((s+ωp1) (s+ωp2)…….)
ωp1 and ωp2….. represent poles.
ωz1 and ωz2….. represent zeros.
In many cases zeros have lower frequency much smaller than ωL. Also one of the
poles will have much higher frequency than all the other poles.
Therefore FL(s)  s / (s+ωp1), where ωp1 = the largest value pole.
In this case, low frequency response of amplifier is dominated by the pole at
s = -ωp1 and lower 3dB frequency is approximately = ωp1
i.e.,ωL ≈ ωp1

This is called as dominant pole approximation. This approximation can be made if

highest frequency pole is separated from the nearest pole or zero by at least 2 octaves
(i.e., factor of 4). If dominant low frequency pole does not exist, then

ωL = √ ( ωp1²+ωp2²-2ωz1²-ωz2²)

If FL(s) = (s (s+10)) / ((s+100) (s+25))
ωp1=100rad/sec is 2 octaves higher than 2nd pole and a decade higher than 0.
Hence, ωL= ωp1 = 100 rad/sec
Or

= = 102 rad/sec

Q.34 Draw the characteristics of an n channel JFET. Enunciate the linear relationship that
represents the ip- Vs characteristics near the origin. (8)

Ans:
The figure below shows a family of ID v/s VDS characteristics of an n channel JFET for
various values of VGS. For small values of VDS (below pinch-off), the depletion region of
the gate would not be affected much by the flow of drain current I D from one end of the
gate to the other end of the gate. This is true for a given value of V GS. As such, a linear
relationship exists between ID and VDS and the JFET behaves like a voltage-controlled
resistor.

Q.35 Why are the characteristics of an n channel JFET, called
static? (2)

Ans:
The characteristics shown in answer to Q 34 are valid for dc conditions. Hence
they are called static characteristics.

Q.36 Write the equation, which represents the boundary between the triode region and
pinch off
region?
(4)

Ans:
The JFET operates in the triode region for
Vds  Vgs - Vp
Where Vds = drain to source voltage
Vgs = gate to source voltage
Vp = pinch off voltage

Q.37 Give the simplified circuit symbol for the depletion type n-channel MOSFET. (2)

Ans:

Q.38 With the help of iD-VDS characteristic curve for small values of VDS explain the
physical operation of depletion type MOSFET (assume IDSS=16mA, VP=-4V
for the device) (12)

Ans:
The depletion type n-channel MOSFET has originally n-type channel region. If a
voltage VDS is applied between drain and source, a current i D flows even for
VGS=0. Applying positive VGS enhances the conductivity of the channel by attracting
more electrons into it (Enhancement mode). Applying negative V GS causes electrons to
be repelled from the channel resulting in lower conductivity and therefore is called
depletion mode operation.
The depletion MOSFET can be operated in 3 distinct regions: Cut off, triode and
saturation region. FET used as an amplifier should be operated in saturation region. For
operation as a switch, cut off and triode regions are used.

For a depletion type n channel MOSFET, threshold voltage V t is negative. The
MOSFET will operate in triode region as long as drain voltage does not exceed the gate
voltage by more than | Vt |. For it to operate in saturation, the drain voltage must be
greater than the gate voltage by at least | V t | volts. The device is cut off when |V GS| < |
Vt |. In saturation region the MOSFET provides a drain current whose value is
independent of drain voltage VDS and is determined by gate voltage only. When VGS=0,
application of positive VDS produces an appreciable drain current IDSS. As VGS decreases
towards threshold, the drain current decreases. At fixed V GS, increasing values of
VDS cause the drain current to saturate as the channel becomes pinched off.

Q.39 What is Hall effect in a semiconductor? How the Hall Effect can be used
to determine some of the properties of a
semiconductor? (7)

Ans:
If a specimen of semiconductor carrying a current(I) is placed in a transverse magnetic
field (B) then an electric field is induced in a direction perpendicular to both I and
B. This phenomenon is known as Hall Effect.
Hall effect is used to measure carrier concentration and mobility. Consider an N type
semiconductor carrying current (I) placed in a transverse magnetic field (B) in the
direction as shown in the Fig.
Due to forces exerted on the electron by electric and magnetic field, a Hall voltage (V H)
is induced as shown. In order to obtain equilibrium state,
F (electric) + F (magnetic) =0
n.q.E + B.J= 0
i.e E = - BJ/n.q
where J = current density
n = electron concentration
q = electronic charge
Fig.
The Hall co-efficient RH is given by RH = 1/n.q
E = + B.J. RH
But E = VH / d
where VH = Hall voltage
d = distance between front and back surface
Also J = I/A = I/d.t
where t = thickness of the semiconductor.
VH /d = B (I / d t)* (1 / n q)
VH = BI / n.q.t or n = BI / q tVH
n = density of electrons.
Conductivity of an extrinsic semiconductor is given by
 = n.q.μn Where μn = electron
mobility &
Or  = p.q.μp μp = Hole mobility
Therefore μn = σ/nq =σRH

Q.40 Draw the circuits of the various transistor configurations. Why common emitter
configuration is mostly used? Give its typical uses. (7)

Ans:
A transistor can be connected in a circuit in the following three configurations.
1. Common base configuration

2. Common emitter configuration

3. Common collector configuration

The reasons for wide use of CE configuration are
(i) High current gain: In CE configuration IC is output current and IB is the input
current. Collector current is given by IC = ß IB. As the value of ß is very large output
current IC is much more than the input current IB. The value of ß is ordinarily high and
ranges from 10 to 500.
(ii) High voltage and power gain: Due to high current gain the CE configuration has
the highest voltage and power gain of the three transistor configurations.
(iii) Moderate output to input impedance ratio: In the CE configuration the ratio of
output impedance to input impedance is small. Therefore this configuration is ideal
for coupling between various transistor stages. CE configuration is used for small
signal and power amplifier applications.

Q.41 What is transistor biasing? What are the basic conditions which are to be necessarily
fulfilled for achieving faithful amplification of input signal in transistor amplifiers? (7)

Ans:
Fixing the d.c values of current and voltages of transistor under quiescent or no signal
condition is biasing. The quiescent point should lie in the central area of an active, linear
region of the transistor.
The basic purpose of transistor biasing is to keep the base emitter junction properly
forward biased and collector base junction properly reverse biased.
The basic conditions required for achieving faithful amplification of input signal
in transistor amplifiers are:
1) Proper zero signal collector current: The value of zero signal current should be at
least equal to the maximum collector current when the signal is present.
2) Proper minimum base emitter voltage: To achieve faithful amplification the base
emitter voltage (VBE) should not fall below 0.5V for germanium and 0.7V for silicon
transistors at any instant.

Q.42 What are the advantages of the FET over a conventional bipolar junction transistor?
Define pinch off voltage, transconductance, amplification factor and drain resistance of
a FET. Explain with the help of circuit diagram how an FET is used as a voltage
amplifier and as voltage dependent resistor
(VDR). (14)

Ans:
FET is a majority carrier device. FET is a voltage controlled current source. An
important advantage of the FET is that it is simpler to fabricate and occupies less space
on a chip than does a BJT. FET has a negative temperature co-efficient at high current
levels, which prevents FET from thermal break down. FET has high switching speed
and cut off frequency.
Pinch off Voltage:
It is the voltage at which the drain current reaches the maximum value and beyond
which drain current becomes constant.
Transconductance (gm):
It is the ratio of small change in drain current (ΔI D) to the corresponding change in gate
to source voltage (ΔVGS) for a constant drain to source voltage VDS. i.e.,
gm = ΔID / ΔVGS constant.
Amplification factor (μ):
It is the ratio of small change in drain to source voltage (ΔV DS) to the corresponding
change in gate to source voltage (ΔVGS) for a small constant drain current ID. i.e.,
μ = ΔVDS / Δ VGS at constant ID.
Drain resistance:
This may be DC or AC. DC or static drain resistance is the ratio of VDS to ID.
i.e RDS = VDS / ID
A.C or dynamic drain resistance is the resistance between the drain and source when
FET is operating in pinch off or saturation region.
rd = ΔVDS /ΔID
FET as an amplifier is shown in Fig.9 i.
Fig:9 (i)
An enhancement n-channel MOSFET is biased with a battery VGS. A time varying signal
vgs which is to be amplified is superimposed on gate to source dc bias V GS. Thus the total
instantaneous gate voltage is
vGS = VGS + vgs
The operating point can be got by intersection of load line and I D versus VDS curve
corresponding to instantaneous values of vGS.
When a sinusoidal signal vGS is applied the instantaneous operating point will move
along the load line in correspondence with total instantaneous voltage v GS. The output
signal is an amplified replica of the input signal. Linear amplification can be obtained by
properly choosing the dc bias point Q and by keeping the input signal amplified.
FET as voltage dependent resistor:
FIG: 9 (ii)
Figure 9 (ii) shows the output characteristics of an FET. It shows the variations of
ID with VDS for constant VGS.
If we consider the slope of the curve for low values of VDS, we see that the slope varies
with variations in VGS. As the slope is related to the resistance, we can say that the
resistance would be different for different values of VGS.
Hence for a given VDS = V1, the resistance depends on gate voltage and thus it is seen
that FET acts as voltage dependent resistor.

Q.43 What is a tuned amplifier? What is the fundamental difference between audio
amplifiers and tuned amplifiers? How is bandwidth related to resonant frequency (fr)
and the quality factor (Q). (7)

Ans:
Tuned amplifiers are the ones, which amplify a specific frequency or a narrow band of
frequencies. Audio amplifiers provide the constant gain over a wide band of frequencies.
Tuned amplifiers are designed to have specific, usually narrow bandwidth. This is
shown in Fig. 10 (a). BWA is the bandwidth of response of a typical audio amplifier,
while BWT is the bandwidth of tuned amplifier and fr is called the center frequency of
tuned amplifier.
Fig. 10(a)

The quality factor Q of a tuned amplifier is equal to the ratio of center frequency
(fr) to bandwidth (BWT) i.e
Q = fr/BWT
Q is determined by the circuit component values. For a parallel resonance circuit is
given by
fr = 1/ (2π√LC) and where XL is the reactance of the inductor having
resistance R.

Q.44 Discuss the terminal properties of an ideal operational amplifier. (7)

Ans:
The Fig. 11(a) shows the schematic of an ideal op-amp. The following are the
important properties of an ideal op-amp.
i) The input impedance of an ideal op-amp is infinite. Hence it draws no current at both
the input terminals.
ii)The gain of an ideal op-amp is infinite ( ), hence the differential input Vd =V1-V2 is
zero for the finite output voltage V0.

Fig. 11(a)

iii) The output voltage V0 is independent of the current drawn from the output terminal.
Thus its output impedance is zero.
This results in the following Characteristic of an ideal op-amp.
a) Infinite Voltage gain: It is denoted as AOL. It is the differential open loop gain.
b) Infinite input impedance: It is denoted as R in and ensures that no current flows into
an ideal op-amp.
c) Zero output impedance: It is denoted as Ro and ensures that the output voltage of the
op-amp remains the same, irrespective of the load.
d) Zero offset voltage: This ensures zero output for zero input signal voltage in an
ideal op-amp.
e) Infinite bandwidth: This ensures that the gain of the op-amp will be constant over
the frequency range from d.c to infinite.
f) Infinite CMRR: This ensures zero common mode gain for an ideal op-amp. Due to
this common mode noise output voltage is zero.
g) Infinite slew rate: This ensures that the changes in the o/p voltage occur
simultaneously with the changes in the input voltage.

Q.45 What is an ideal diode? Sketch the characteristics of an ideal diode. (7)

Ans:
An ideal diode may be defined as a two terminal device which
a. Conducts with Rf = 0, when forward biased
b. Rr = ∞, when reverse biased
In other words, an ideal diode acts as a short circuit in the forward direction and as an
open circuit in the reverse direction. An ideal diode behaves like a switch which is
closed in the forward direction and open in the reverse direction.
VI characteristics of an ideal diode:
The VI characteristics of an ideal diode are shown in Fig. 12a. The part of the
characteristics in forward biased condition coincides with the i D axis, and the part for
reverse condition coincides with the VD axis as shown by the dark lines.

Fig.12a

Q.46 Describe the construction and operation of JFET. How does it differ from a MOSFET?
Draw the equivalent circuit of a JFET and explain how do we bias for operation as an
amplifier.
(7)
Ans:
The basic structure of an n-channel JFET is as shown in Fig.14a(i). The drain and source
terminals are made by ohmic contacts at the ends of n-type semiconductor bar. Gate is
formed by electrically connecting two shallow p+ regions. The n-type region between
two p+ gates is called the channel through which majority carriers flow between the
source and the drain.
Operation:
Gate regions and channel constitute pn junction. In normal operating mode, this pn
junction is maintained in reverse biased state. Gate to source voltage is negative and
drain to source voltage is positive. This reverse biases the junction, and hence the
depletion region exists. The depletion region contains immobile charges.
Fig.14a(i)

Also, depletion region extends more into region of lower doping. Since gate region is
heavily doped than the channel region, depletion region penetrates more deeply into the
channel. The conductivity of this region is nominally zero because of unavailability of
charge carriers. Therefore, as reverse bias increases, the effective width of the channel
decreases. At specific value of gate to source voltage (VGS) the channel width becomes
zero because all the free charges have been removed from the channel. This voltage is
called pinch off voltage (Vp). Therefore, for a fixed drain to source voltage, the drain
current will be a function of reverse bias voltage across the gate junction.
In a MOSFET metal gate electrode is separated by an oxide layer from the
semiconductor channel.
FET as an amplifier: Fig.14a(ii) shows a Common Source (CS) configuration. The
signal to be amplified is V1. VGG provides the necessary reverse bias between gate and
source of JFET. This is the biasing arrangement for the operation of JFET as an
amplifier.

Fig.14a(ii)

Low frequency small signal equivalent circuit of JFET
Fig.14a(iii)

Q.47 Draw the circuit diagram of a collector tuned amplifier and derive the expression
for the voltage gain at the tuned frequency. (7)

Ans:
The collector tuned circuit is shown in Fig.16a (i)

Fig.16a(i)

Fig.16a(ii)

Fig.16a(iii)

The equivalent circuit of the amplifier is shown in Fig.16a(ii),
Rt = Ro || Rp || Ri
where R0 = output resistance of current generator gmVbe and is equal to (1/hoe)
Ri = input resistance of next stage
Rp = equivalent internal resistance of L calculated when series L circuit
is represented by its equivalent parallel circuit.
Voltage Gain AV= Vo/Vi
From Fig.16a(iii) output voltage can be given as
Vo = -gmVbeZ
where Z = impedance of C, L and Rt in parallel or,
Z = Rt/(1+2jQeffδ)
Qeff = Rt/ωrL
and ωr = resonant frequency
and δ = fractional variation in resonant frequency = (ω-ωr) / ωr
At resonant frequency ω = ωr and δ = 0.
Z (at resonance) = Rt
Fig.16a(iii)shows the final equivalent circuit of Fig.16a(ii).
Hence Vo = -gmVbeRt at resonance
Also Vbe = Vi(rbe/(rbb+rbe)) ( from Fig.16a(ii) neglecting Cs)
Vo = -gmVi( rbeZ / (rbb+rbe))
AV = Vo/Vi = -gmVi(rbeZ/(rbb+rbe))
= -gm(rbe/(rbb+rbe)) x (Rt/(1+2jQeffδ))
At resonance, voltage gain is
AV = -gm(rbe/(rbb+rbe)) x Rt

Q.48 Explain the reasons for potential instability in tuned
amplifiers. (7)

Ans:
A tuned amplifier is required to be highly selective. Instability is because of
positive feedback in tuned amplifiers.

Q.49 What are ‘intrinsic’ and ‘extrinsic’ semiconductors? Comment on the conductivity of
extrinsic
semiconductor.
(4)

Ans:
A pure semiconductor which is not doped is said to be intrinsic semiconductor. They
have very low conductivity. When pure semiconductors are mixed (doped) using
trivalent or pentavalent elements, we get extrinsic ones, which are p type in the former
case and n type in the latter.
The crystalline nature of the original semiconductor is unaltered by doping as the doping
element atoms replace the original semiconductor atoms without disturbing the crystal
structure as such. This happens by participation of electrons of doping element with
those of semiconductor in forming bonds. However, either an extra electron as in the
case of pentavalent dopant or a free hole as in the case of trivalent dopant greatly
enhances the conductivity.

Q.50 Explain the classification of power amplifiers according to operational
modes. (6)

Ans:
Classification according to operation mode:
The duration of device conduction with respect to input signal cycle period determines
the class of operation.
Class A: Device current flows for the full period of input (Q point in the active region of
the device).
Class B: Device conducts only during one half cycle of input. (Q point just at the cut off
region of the device)
Class AB: Device conducts for greater than half cycle but less than full cycle of input.
Class C: Device conducts for less than half cycle of input. (Q point beyond cut off).
These different operations are achieved by appropriate biasing of the device by setting
up the desired quiescent current and voltage (or Q-point). Fig. 20 b. illustrates the
conditions for class A and class B.

Fig. 20 b

Q.51 Draw a block diagram of a single loop feedback amplifier, and explain the function of
each block. What are the characteristics of an amplifier that are modified by negative
feedback? For the four topologies of negative feedback, indicate whether the input
impedance and out impedance increase or decrease as a result of
feedback. (9)

Ans:
The block diagram of a single loop feedback amplifier is as shown in Fig. 21a
Signal source: The signal source is either a voltage source or a current source providing
input Xs.
Comparator or mixer: This block combines the source signal with the feedback signal.
Depending upon the nature of signal and feedback this may be series or shunt mixing.
Basic amplifier: The ratio of output signal to the input signal of a basic amplifier is
represented by ‘A’ and depends on the type of amplifier.
Sampling network: It is used to sample the output signal of the basic amplifier. When
voltage has to be sampled, feedback network is connected in parallel to the output
terminals and in series when current is to be sampled.
Fig. 21a

Feedback network: This is a passive two port network providing a known fraction of
the input to the mixer at input.
The characteristics of an amplifier that are modified by negative feedback are:
1. Sensitivity of transfer characteristics.
2. Non linear distortion.
3. Noise.
4. Frequency distortion.
5. Bandwidth.
6. Input and output impedances of the amplifier.
Table below shows how the input impedance and output impedance in the four
topologies of negative feedback are affected.

Voltage Current Current Voltage
Series Series Shunt Shunt
I/P impedance Increases Increases Decreases Decreases
O/P impedance Decreases Increases Increases Decreases

Q.52 Write short notes on any
two. (2x7)
i) Nyquist criterion.
ii) BIFET and BIMOS circuits.
iii) Schmitt trigger.
iv) The digital comparator.

Ans:
i) Nyquist criterion:
Fig.22 (i)-Stable system Fig.22(ii) unstable system

The diagrams above shows Nyquist plot for 2 types of systems (stable and
unstable). Solid line is for positive frequencies. The Nyquist plot intersects the negative
real axis at a frequency 180. If intersection occurs to the left of point (-1, 0), then the
magnitude of loop gain at this frequency is greater than unity and amplifier will be
unstable. If intersection occurs to the right of point (-1, 0) the amplifier will be stable. In
other words, if Nyquist plot encircles the point (-1, 0) then amplifier will be unstable.
Nyquist plot is used to determine whether there are any poles on the right half of s-plane
for a feedback amplifier.
Nyquist criterion states that the number of clockwise encirclements of the point –1+j0 is
equal to the difference between the number of poles and zeros of F(s)=1+T(s) in the
right half of s plane. (T(s) is the return ratio).
Closed loop gain of feedback amplifier = AF(s) = AOL(s) / F(s)
AOL(s) = loop gain of the amplifier without feedback.
Therefore for a stable feedback amplifier, the Nyquist plot of function AF(s) should not
encircle the point –1+j0. The clockwise encirclements of –1+j0 are determined by
drawing a radius vector from –1+j0 to Nyquist diagram and tracing the locus of points
from - <  < .
In Fig.22 (i) there is no encirclement, therefore AF(s) has no right half poles and hence
the amplifier is stable.
In Fig.22 (ii)there are two encirclements, therefore AF(s) has two right half poles and
hence the amplifier is unstable.
ii) BIFET and BIMOS circuits:
Ion implantation permits the fabrication of JFETs / MOSFETs and BJTs on the same
chip. The ICs fabricated by this process are called as BIFET/BIMOS.
(BIFET=BJT+FET, BIMOS=BJT+MOSFET). All BIFET (BIMOS) op-amps use
FET input stages. The remaining stages use BJTs. FET input stages have the
following advantages over BJT input stages:
1) Higher differential mode input resistance.
2) Lower input current and hence decreased input offset currents and higher slew rates.
The input resistances of FET differential stages are 4 times higher in magnitude than
that of BJTs. Input bias current of JFET is the reverse saturation current IGSS of reverse
biased gate to channel junction. The gate current of FET is usually much smaller than
the base current of BJT for similar values of drain/collector currents. Since the input
current IG is very small, the offset current due to device mismatch is also much smaller
than that with BJT circuits. For a given drain current ID, value of gm in FET is smaller
than the gm of BJT biased at IC= ID. Therefore, the reduction of gm results in increased
slew rate. This lower value usually results in lower differential mode gain in FET stage
compared to that with BJT circuits. To overcome this limitation, BIFET and BIMOS
Op-amps employ three-stage architecture.

iii) Schmitt trigger:
It is also called as regenerative comparator. It converts any given waveform into a
rectangular output. The Schmitt trigger circuit is shown in Fig 7 (iii a). Input is
applied to inverting terminal (2) and feedback voltage to non-inverting terminal (1).
Assuming that the output resistance of the comparator is negligible compared with
R1+R2, we get V = [R2 / (R1+R2)] Vo.
1
Let vo = Vz+VD

Vz = drop across reverse biased zener.
VD = drop across forward biased zener.
And if v2<v1 so that vo= +Vo
Fig 22 (iiia) Schmitt Trigger

The voltage at non-inverting terminal is given by
VA+ R2 (V0-VA) = V1 (v2<V1)
R1+R2
If v2 is now increased, then vo remains constant and vo = + V0 constant until v2=V1, when
v2 exceeds V1, v0 changes.
At this threshold voltage, the output regeneratively switches to -V0 and remains at this
value as long as V2>V1. This is shown in Fig 22 (iiib).
Fig 22 (iii c): Hysteresis curve

The voltage at non-inverting terminal for V2>V1 is given by
V1 = VA- R2 (Vo+VA) = V2 (V2<V1)
R1+R2
Note that and difference between these 2 values is called as hysteresis VH.
VH=V1-V2
If we now decrease V2, output remains at –Vo until V2 = V2. At this voltage a
regenerative transition takes place as indicated in fig 22(iii c) and output returns to
+Vo almost instantaneously.
This circuit can be used as a squaring circuit. The output is asymmetric square
wave, the amplitude of which is independent of peak-to-peak value of input signal. The
input and output waveforms are as shown in the following figure below.
Fig 22 (iiid)

(a) Alternative Solutions I
Schmitt trigger:
Consider the circuit shown in figure 22 (i). This circuit converts an irregular shaped
waveform to a square wave or pulse. The circuit is known as the Schmitt trigger or
squaring circuit.
The input voltage Vin triggers the output Vo every time it exceeds certain voltage
level called the upper threshold voltage Vut or becomes smaller than the lower threshold
voltage Vlt as in Fig below. These threshold voltages are maintained in the circuit by
using the voltage divider R1, R2 where the voltage across R1 is fed back to the (+) input.
The voltage across R1 is dependent upon the value and polarity of Vo. When Vo =
+Vsat voltage across R1 is called upper threshold voltage Vut, Where Vut = (R1/(R1 + R2))
*Vsat . When V0 = -Vsat voltage across R1 is referred to as the lower threshold voltage
Vlt and is given by
Vlt = (R1/ (R1 + R2))* (-Vsat).
If Vut & Vlt are larger than the input noise voltages, +ve feedback will eliminate the false
output transitions & due to regenerative action Vo switches faster between +Vsat and
–Vsat. ROM ≈R1║ R2 is used to minimize the offset problems.
A comparator with a positive feedback exhibits hysteresis. When input of the

comparator exceeds Vut, its output switches from +Vsat to –Vsat & reverts to its original
state. Hysteresis voltage Vhy = Vut– Vlt.
(b) Alternative Solution II
Schmitt trigger is used to change a slowly varying input voltage into an output
waveform of an abrupt discontinuous change that occurs at a precise value of the input
voltage. It is used as a squaring circuit.
Schmitt trigger is also called as regenerative comparator. Input is applied to inverting
terminal and feedback voltage to non-inverting terminal .The Schmitt trigger circuit is
as shown in the Fig.(i). It consists of two similar transistors Q 1 and Q2 coupled through
RE and resistors R1, R3, R4 from a voltage divider across VCC to –VBB which places a
small positive voltage on the base of Q2.
Circuit operation:
When positive half cycles of input A.C voltage is applied to the input and suppose this
positive voltage is sufficient to overcome the reverse bias on the base of Q 1, The
sequence of events that follows is as follows.
1. Q1 comes out of cut off and starts to conduct.
2. Its collector voltage drops. (swings negative).
3. This negative swinging is coupled to the base of Q2 via R3 reducing its forward
bias and hence its IE .
4 With reduced IE voltage drop across RE is reduced.
5. Consequently, the reverse bias of Q1 is further lowered and it conducts more
heavily.
6. As a result, collector voltage of Q1 falls further there by driving Q2 still closer to cut
off.
This process ends up with
1. Q1 conducting at saturation with its collector voltage almost zero.
2. Q2 becoming cut off with its collector voltage nearly VCC.
Fig.(i)-Schmitt Trigger

This circuit can be used as a squaring circuit. The output is asymmetric square wave, the
amplitude of which is independent of peak-to-peak value of input signal. The input and
output waveforms are as shown in the Fig.(ii).
Fig.(ii)
Hysteresis:
Fig.(iii)
The transfer characteristics i.e., Vin v/s Vo is shown in Fig.(iii).
Due to the positive feedback the comparator is said to exhibit hysteresis. The portion
without arrows may be traversed in either direction, but other segments can be obtained
only if V2 is increased or decreased in given direction.
Because of hysteresis, circuit triggers at a higher voltage for increasing than for
decreasing signals.
iv) The digital comparator:
A comparator is used to detect whether a binary number is greater than, equal to or less
than another binary number. Consider two single bit numbers A and B,
One bit comparator

Where C=1 for A>B
E=1 for A=B
D=1 for A<B
a) Let A=B
EX - NOR gate is an equality detector. The output E of EX-NOR is given by
b) Condition A>B is given by C=AB=1 because if A>B then A=1 and B=0
therefore C=1 here
if A=B or A<B (A=0, B=1) then C=0.
c) Condition A<B is determined from D=AB=1
Consider a 4-bit comparator. (A & B are 4 bit numbers).
a) For A = B, A3 = B3, A2 = B2, A1 = B1, A0 = B0
Therefore E=E3E2E1E0
If A = B then E = 1
If A  B then E = 0
b) For A>B: A3 >B3 (MSB)
Or A3=B3 and A2>B2
Or A3=B3 and A2=B2 and A1>B1
Or A3=B3 and A2=B2 and A1=B1 and A0>B0
This is given by
C = B3A3 +B2E3A2 +B1 E3E2A1 +B0 E3E2E1A0
If A>B then C = 1
d) For A<B: in the above equation interchange A and B, to get the output D.
Digital comparators are useful in comparing binary words and the result of comparison
is used to initiate various actions in a digital system.

Q.53 With the help of a circuit diagram, explain the working of a half wave rectifier
with capacitor
filter. (8)
Ans:
Fig 23 (i)

The circuit of a half wave rectifier is shown in the Fig 23 (i). For a sinusoidal input, the
capacitor charges to the peak (Vp) of input. Then the diode cuts off and the capacitor
discharges through the load resistor R. As the capacitor is discharging, the voltage at the
cathode of the diode decreases. At some instant of time input voltage exceeds the
capacitor voltage and the diode turns on. The capacitor now starts charging and the
process repeats, and is shown in the figure 8 (ii b).To keep the output voltage from
decreasing too much, during capacitor discharge, value of C is selected so that the time
constant RC is much greater than the discharge interval.

Q.54 Draw the load voltage waveform for a half wave and full wave rectifier with a
capacitor filter (no explanation required). (6)

Ans:
Fig 23 (ii a): for Half wave rectifier

Fig 23 (ii b): for Full wave rectifier

Q.55 Explain the terms fan in and fan out in logic gates. (4)
Ans:
Fan in: Fan in of a gate is the number of inputs it can accept without affecting the input
characteristics of the gate. If fan in is exceeded, a logic gate will produce either an
undefined or incorrect output state. Also, the input signals may be deteriorated because
of excessive loading.
Fan out: A logic gate may be capable of providing input to several similar gates. Fan
out is the number of similar circuits a gate can drive without any effect on its output
characteristics.

Q.56 Using 4 variable K map, find all the prime implicants of the following switching
function.
f(w,x,y,z)=(0,1,2,5,7,8,9,10,13,15)
And from the set of prime implicants thus obtained, find out minimal sum of
product expression of the function. (10)

Ans:
The K map is shown above for the given function. The prime implicants are
(i) xz (ii)xy (iii)xz
The minimum SOP representation is:
f (w,x,y,z) = xz +xy+xz

Q.57 What is the function of A/D converter? (4)

Ans:
Data obtained from the physical system will be analog in nature. For processing
these signals several methods are employed and all these systems require the inputs in
the digital form. So if the analog signals are to be processed and analyzed, they should
be converted into digital form. Therefore A/D converters are used to convert the signals
in analog form into digital form.

Q.58 Explain 3 bit parallel comparator ADC with the help of a diagram and give its truth
table. (10
)

Ans:
Parallel comparator ADC is the fastest type. In this method, analog voltage Va is
applied to all the comparators. The reference voltage to first comparator is (7/8) V, to
second comparator is (6/8) V and so on. The reference voltage to last comparator is V/8.
Above diagram shows a 3 bit ADC. It requires 7 comparators.
Working: When input voltage is below the reference voltage of the comparator, the
output of the comparator is low (logic 0). When input voltage is above the reference
voltage, the output of that comparator is high (logic 1).

For example:if input voltage Va is between (2/8) V and (3/8) V then W1=1, W2=1 and all
other W values are 0. For this, the digital output of the encoder should be 2 (Y2=0, Y1=1,
Y0=0) which is interpreted as an analog voltage between (2/8) V and (3/8) V.
When Va < (1/8) V, then W1 to W7 are all 0 and output is zero. (Y2=Y1=Y0=0).

The truth table is as follows:
INPUTS OUTPUTS
W7 W6 W5 W4 W3 W2 W1 Y2 Y1 Y0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 1 0 0 1
0 0 0 0 0 1 1 0 1 0
0 0 0 0 1 1 1 0 1 1
0 0 0 1 1 1 1 1 0 0
0 0 1 1 1 1 1 1 0 1
0 1 1 1 1 1 1 1 1 0
1 1 1 1 1 1 1 1 1 1

Q.59 What is an oscillator? How does it differ from an amplifier? What are the essential
parts of an oscillator
circuit? (7)

Ans:
The oscillator is a circuit which generates signals of constant amplitude and frequency.
The circuits which generate sine waves using resonance phenomena are known as linear
oscillators. The circuits which generate square, pulse or rectangular waveforms are
called as nonlinear oscillators.
Fig 27a: Basic structure of a sinusoidal oscillator

Amplifier is a device which produces an enlarged version of the output signals same as
that of input. Amplifier is an energy conversion device, which gets energy from the dc
source and converts into an a.c source. Conversion is controlled by the input
signal. Oscillator produces an output signal without any input signal of any
frequency. It produces output signal, as long as the dc power is supplied.
An amplifier usually employs negative feedback whereas the oscillator will have
positive feedback.
The essential parts of an oscillator circuit are
i) Transistor amplifier
ii) Frequency selective network: The Frequency selective network is connected in
positive feedback loop. A part of the output signal is fed to the amplifier in phase to aid
the oscillations, as shown in Fig 27a,where Xs= 0 for an oscillator.

Q 60 Draw the circuit diagram of Colpitts oscillator and explain its working. (7)

Ans:
The circuit diagram of a Colpitts oscillator is as shown Fig 27b.It uses two capacitors
C1 and C2 placed across a common inductor L and the center of the two capacitors is
tapped. This forms the frequency selective feedback network. The transistor circuit is the
amplifier.
Operation:
When the circuit is turned on, the capacitors C 1 and C2 are charged. The capacitors
discharge through L, which sets up oscillations of frequency
fo = 1 / 2π√LC
Where C = C1 C2 / (C1 + C2). The output voltage of the amplifier appears across C1 and
feedback voltage is across C2. The voltage across C2 is 180o out of phase with the
voltage across C1. The voltage across C2 is fedback to the transistor providing a positive
feedback.

Fig 27b

A phase shift of 180o is produced by the transistor and a further phase shift of 1800 is
produced by C1-C2 voltage divider. Therefore, the feedback is properly used to produce
continuous undamped oscillation.

Q.61 What is an integrator? Derive the formula for its output voltage. Explain its working
with neat and clean waveform i) In case of square wave input ii) In case of sine wave
input. (8)

Ans:
A circuit in which the output voltage is directly proportional to the integral of the input
voltage is called an integrator. Integrators can be passive integrator or active
integrator. Fig 28a(i) shows an active integrator using op-amp.
Fig 28a(i)
Expression for output voltage:
Since node B is grounded, node A is also at ground potential. Hence V A=VB=0. As the
input current of op- amp is zero, the current through C F is the current through R1. From
input side
I = Vin/R1
From output side
I = CF d(VA-VO)/dt = - CF(dVO/dt )
Therefore
Vin/R1 = - CF (dVO/dt )
Integrating
t
∫ (Vin/R1) dt = - CF ∫dVo / dt = - CF VO
0 t
Vo = -(1/R1 CF) ∫Vin dt
0

Working of an integrator for square wave input:
Let the input waveform be a square wave as shown in Fig 28a(ii). It can be observed that
the square wave is made up of steps i.e., step of ‘A’ between time period of ‘0’ to T/2
while a step of ‘-A’ between T/2 and T.
Mathematically it can be expressed as
Vin (t) = A, 0<t<T/2
= -A, T/2<t<T
The output for step input is a straight line with a slope of ‘–A’. So in the period ‘0’ to
‘T/2’, the slope is ‘–A’. From ‘T/2’ to ‘T’ slope becomes – (-A) i.e. +A.
Therefore output VO (t) = -At 0<t<T/2
= +At T/2<t<T.
Fig 28a(ii)
Fig 28a(iii)

Working of an integrator for sine wave input signal:
Let the input waveform is purely sinusoidal with a frequency of  rad/sec.
i.e., Vin (t) = Vm Sin t, where Vm is the amplitude of sine wave and T is the period of
the waveform. To find the output waveform, let R1C1 = 1 and VO (0) = 0V.
VO (t) = - ∫ Vin dt = - ∫Vm sin t dt
= - Vm [1/ (-cos t)] = -Vm / (-cos t)
Thus the output of an integrator is a cosine waveform for a sine wave input. The
waveforms are as shown in Fig 28a(iii).

Q.62 Derive the formula for summing amplifier and on averaging amplifier in non
Inverting configuration. (6)

Ans:
A summer that gives non inverted sum of the input signals is called as
non- inverting summing amplifier. The circuit is shown in Fig 28b(i).
Fig 28b(i)

Let the voltage at node B be VB. Node ‘A’ is at the same potential.
Therefore VA = VB
From input side I1 = (V1 – VB)/R1 and I2 = (V2 – VB)/R2
As input current of op-amp is zero, I1 + I2 = 0
Therefore (V1 – VB)/R1 + (V2 – VB)/R2 = 0
V1/R1 + V2/R2 = VB (1/ R1 + 1/ R2)
This gives, VB = (R2V1 + R1V2)/ (R1 + R2)
At node A, I = VA/R = VB/R and I = (VO – VA) / R3 = (VO – VB) /R3
Therefore, VB/R = (VO – VB) /R3
i.e., VO/R3 = VB (1/R3 + 1/R)
Therefore, VO = VB [(R + R3) / R]
i.e., VO = ([R2V1 + R1V2] / [R1 + R2])* ([R + R3] / R)
Therefore VO = R2(R + R3) V1 / R (R1 + R2) + R1(R + R3) V2 / R (R1 + R2)
If R1 = R2 = R = R3 we get VO = V1 + V2
If in the summer circuit the value of resistance are selected as R1 = R2 = R and
R3 = R / 2. Then
VO = [(R/2) V1/R + (R/2) V2/R]
= [(V1 + V2)/2]
Thus the magnitude of the output voltage is the average of the input voltages. In that
case the input becomes a averaging amplifier.
_ _
Q.63 For the logic expression Z = AB + AB
i) Obtain the truth table. (2)
ii) Name the operation performed (1)
iii) Realize this operation using *AND, OR, NOT gates * only NAND gates (4)

Ans:
(i) Truth Table

_ _ _ _ _ _
A B A B AB AB AB + AB = Z
0 0 1 1 0 0 0
0 1 1 0 0 1 1
1 0 0 1 1 0 1
1 1 0 0 0 0 0
(ii) The operation performed is Exclusive OR operation.
(iii)Circuit realization using AND, OR, NOT gates.

(iv)Circuit realization using NAND gates only.

Q.64 State and prove De Morgan’s theorem using truth table. (7)

Ans:
The De Morgan’s theorem can be stated as follows
Theorem 1: The complement of a product of variables is equal to the sum of the
complements of the individual variables. Symbolically,
(A.B.C.D…….) = A + B + C + D +………
Theorem 2: The complement of the sum of variables is equal to the product of
individual complements of variables. Symbolically,
___________ _ _ _
(A + B + C +…..) = A. B. C . . . ……….
The theorems can be verified by using truth table.
The truth table shown in table 1 for two variables A and B gives justification for
theorem 1, and table 2 for theorem 2.
____ _ _ _ _
A B A+B A+B A B A.B
0 0 0 1 1 1 1
0 1 1 0 1 0 0
1 0 1 0 0 1 0
1 1 1 0 0 0 0
Table 1
___ _ _ _ _
A B AB AB A B A + B
0 0 0 1 1 1 1
0 1 0 1 1 0 1
1 0 0 1 0 1 1
1 1 1 0 0 0 0
Table 2

Q.65 What is a JK flip flop? How does it differ from the SR flip flop in construction and
operation?
(7)
Ans:
A JK flip flop is a refinement of the RS flips flop, in that the indeterminate state of the
RS type is well defined in the JK type. When input to RS flip flop are R=S=1, both
outputs of flip-flop are at logic ‘0’. When J = K =1 JK is flip flop, it complements the
outputs. That is if
Q =1, it switches to Q =0 and vice versa. Fig 30 (a) shows the logic diagrams of SR flip
flop and JK flip flop. In the logic circuit of JK flip-flop output Q is ANDed with K and
CP inputs so that the flip-flop is cleared during a clock pulse only if Q was previously 1.
Q’ is ANDed with J and CP inputs so that the flip-flop is set with a clock pulse only if
Q’ was previously 1.

RS flip flop Fig 30 (a) JK flip flop

Thus JK flip-flop behaves like an RS flip flop, except when both J & K are equal to 1.
When both J & K are 1, the clock pulse is transmitted through one AND gate only, the
one whose input is connected to the output which is presently equal to 1. Thus if Q = 1,
the output of the upper AND gate becomes 1 upon application of a clock pulse and the
flip-flop is cleared. If
Q’ = 1, the output of the lower AND gate becomes a 1 d the flip flop is set. In either case
the output state of the flip-flop is complemented.

Q.66 What is a sequential logic circuit? How does it differ from the combinational
type? (4)

Ans:
A sequential circuit is one whose output depends on the present inputs as well as on the
past outputs In a combinational circuit, output at any instant of time depends only on the
present inputs. Such systems are called memory less systems.
A block diagram of a sequential circuit is shown in Fig 30 (B). A combinational circuit
and storage elements are interconnected to form the sequential circuit. Storage elements
store binary information.
Fig 30 (B)

The sequential circuits receive binary information from its environment via inputs.
These inputs together with the present state of the storage elements, determine the
output. They also determine the values used to specify the next state of the storage
elements.

Q.67 Show how a full adder may be implemented by using two half adders. (3)

Ans:
Fig 30 (c )

Q.68 Write short notes on
(i) Voltage Regulator
(ii) Multivibrator
(iii) Shift Register (2x7)

Ans:
(i) Voltage Regulator:
Voltage regulation may be defined as the ability of the power supply or source to
maintain a constant output voltage in spite of a.c voltage fluctuations and changes in the
load resistance. Mathematically, it is given by the relation,
( (Vmax –Vmin) /Vmax )x 100
Vmax = maximum d.c. output voltage.
Vmin = minimum d.c. output voltage.
In general, the voltage regulation may also be expressed as
((VNL –VFL) /VFL) x 100
VFL = full load voltage of the supply.
VNL = no load or open circuit voltage of the supply.
It is a known fact, that all the electronic devices and circuits require a constant d.c
voltage for their operation, and a fluctuating d.c voltage result in erratic operation of the
electronic devices. The d.c voltage can be supplied from dry cells or batteries. But these
are expensive compared to the conventional regulated d.c power supplies. The regulated
d.c power supply is made by converting the domestic a.c supply to d.c supply. The
essential elements, which constitute a regulated d.c power supply, are given below:
1)Rectifier ,
2)Filter, and
3)Voltage regulator.
The rectifier is the front or the first element of a regulated d.c power supply, the filter is
the second or the intermediate element and the voltage regulator is the last element.
Working: As an example let us consider a combination of full wave rectifier and a filter
circuit connected to an a.c. input voltage source. When the a.c input voltage, of the
rectifier input, changes above or below its normal value, it will cause a change in d.c
voltage produced at the filter output. A similar change in d.c voltage may also occur,
when the load resistance connected at the filter output changes above or below its
normal value. It means that the d.c. output voltage fluctuates whenever the a.c input
voltage or the load resistance varies above or below the normal values.
Although there are many types of voltage regulators, yet the following ones are some of
the important types of voltage regulators,
1. zener diode shunt regulator.
2. Transistor shunt regulator.
3. Transistor series regulator.
4. Controlled transistor series regulator.
5. Monolithic regulator.
(ii) Multivibrator: An electronic circuit that generates square wave is known as a
multivibrator. A multivibrator is a switching circuit which depends, for
operation, on positive feedback. It is basically a two stage amplifier with output
of one given as the input to the other as shown in Fig: 31(iii).
.
Fig: 31(iii)

The circuit operates in two stages controlled by the circuit conditions. Each amplifier
stage supplies feedback to the other in such a manner that will drive the transistor of one
stage to saturation and the other to cut off. After a certain time, controlled by circuit
conditions, the action is reversed i.e., saturation stage is driven to cut off and cut off
stage is driven to saturation. The output may be taken across any of the stages and may
be rectangular or square wave depending upon the circuit conditions.
Types of multivibrators:
Multivibrators are classified into three categories.
a) Astable multivibrator or free running multivibrator
b) Monostable multivibrator or one-shot multivibrator
c) Bi-stable multivibrator or flip-flop multivibrator
a) Astable multivibrator or free running multivibrator alternates automatically between
the two states and remains in each state for a time dependent upon the circuit constants.
Thus, it is just an oscillator since it requires no external pulse for its operation. Because
it continuously produces the square-wave output, it is often referred to as a free running
multivibrator.
b) Monostable multivibrator or one-shot multivibrator has one stable state and one
quasi-stable state. The application of input pulse triggers the circuit into its quasi-stable
state, in which it remains for a period determined by circuit constants. After that period
of time the circuit returns to its initial state, the process is repeated upon application of
each trigger pulse.
c) Bi-stable multivibrator or flip-flop multivibrator has two stable states. It requires the
application of an external triggering pulse to change the operation from one state to the
other. Thus one pulse is used to generate half-cycle of square wave and another pulse is
to generate the next half-cycle of square wave. It is also known as flip-flop multivibrator
because of its two possible states it can assume.
d) Shift registers: A register capable of shifting its stored bits laterally in one or both
directions is called a shift register. The logical configuration of a shift register consists
of a chain of flip flops in cascade with the out put of one flip flop connected to the input
of the next flip flop. All the flip flops receive a common clock pulse, which activates the
shift from each stage to the next.
The simplest possible one is that which uses only D flip flops as shown in figure 18.
The output of a given flip flop is connected to the D input of the flip flop at its right.
Clock is common to all flip flops. Serial input SI is the input to the leftmost flip flop
during the shift. The serial output SI is taken from the output of the right most flip flop.
Fig 18 A 4 bit shift register

Shift registers can be used for converting serial data to parallel data and vice versa. If we
have access to all the flip flop outputs of a shift register, then information entered
serially by shifting can be taken out in parallel from the outputs of the flip flops or vice
versa.

Q.69 Discuss the basic concept behind the operation of a Wien-bridge oscillator with the help
of suitable circuitry and derive expression for relevant oscillation
frequency. (7)

Ans:
Wein-bridege oscillator is used in audio frequency range. It uses two transistors, each
producing a phase shift of 1800 and thus producing a total phase shift of 3600 or 00.
The Fig. 32a. shows the circuit diagram of an Wien-bridge oscillator. It is a two stage
amplifier with an RC bridge circuit. RC bridge circuit is a lead lag network. The phase
shift across the network lags with increasing frequency and leads with decreasing
frequency. By adding a feedback network, the oscillator becomes sensitive to a signal of
only one particular frequency. This frequency is that at which Wien bridge is balanced
and for which phase shift is 00.

Fig. 32a.
The bridge is balanced only when
R4 (R2 / (1+jωC2R2)) = R3 (R1 – j / ωC1)
R2 R4 = R3 (1 + jωC2R2) (R1 – j / ωC1)
or
R2R4 – R3R1 – (C2 / C1) R2R3 + (jR3 / ωC1) – j ωC2R2R1R3=0
Separating real and imaginary parts, we have
R2R4 – R3R1 – (C2 / C1) R2R3=0
or
(C2 / C1) = (R4/ R3) – (R1 / R2)
and (R3 / ωC1) – ωC2R2R1R3=0
ω2= (1 / C2C1R2R1) or ω=√(1 / C2C1R2R1)
fo= 1/ (2 √(R1R2C1C2))
If R1 = R2 = R and C1 = C2 = C then
fo = 1/(2 x R x C) and R4=2R3

Q.70 What are the main considerations which are to be kept in view while selecting an
oscillator for a particular
application? (7)

Ans:
The main considerations which are kept in view while selecting an oscillator for a
particular application are

1.Frequency range:
The oscillator selected for a particular application should be capable of supplying an
output signal whose upper and lower frequency limits exceeds those required by the
application. The frequency of operation of the oscillator has been selected, it should not
drift from the related frequency.
2.Accuracy and dial resolution:
The accuracy of an oscillator specifies how closely the output frequency corresponds to
the frequency indicated on the dial of the output frequency value the dial setting can be
read.
3.Amplitude and frequency stability:
The amplitude stability is a measure of an oscillator’s ability of maintaining a constant
voltage amplitude with variations in the output signal frequency. Frequency stability
determines how closely the oscillator maintains a constant frequency over a given time
period.
4.Waveform distortion:
This quantity is the measure of how closely the output waveform of the oscillator
resembles a pure sinusoidal signal. The distortion should be kept minimum.
5.Output impedance:
This is the impedance value of load which must be connected to it for maximum power
transfer. The output impedance of the oscillator be equal to the characteristic impedance
of the system to which it is to be connected.

Q.71 In a circuit shown in figure below, calculate and sketch the waveforms of current i over
one period of input voltage. Assume the diodes to be
ideal. (14)

Ans:
Between the duration 0 and /2 both diodes are ON.
Between the duration /2 and diode D2 is ON.
Between the duration and 3 /2 both diodes are OFF.
Between the duration 3 /2 and 2 diode D1 is ON.
i = 1/2 (sin t + cos t) for 0 ≤ t ≤ /2
i = 1/2 (sin t) for /2 ≤ t ≤
i = 0 for ≤ t ≤ 3 /2
i = 1/2 (cos t) for 3 /2 ≤ t ≤ 2

Q.72 State the principle of operation of a bistable multivibrator with the help of a circuit
diagram. (7)
Ans:
Bistable multivibrator (BVM)
It has two absolutely stable states. It can stay in one of its two states indefinitely, and
changes to other state only when it receives a trigger pulse from outside.
Since one trigger pulse causes the multivibrator to flip from one state to another and the
next pulse causes it to flip back to its original state, the multivibrator is also known as
“flip-flop” circuit.
Fig.34a
Circuit operation:
In the circuit shown in Fig.34a, when Q1 is conducting, then the fact that point A is at
nearly 0V makes the base of Q2 negative (by the potential divider R2-R4) and holds
Q2 OFF. Similarly, when Q2 is OFF, the potential divider from VCC to –VBB (RL2, R1, and
R3) is designed to keep the base of Q1, at about 0.7V, ensuring that Q1 conducts. Now
suppose a positive pulse is applied to R, it will cause Q 2 to conduct. As collector of
Q2 falls to ‘0’, it cuts Q1 OFF and bistable multivibrator switches to its other state.

Q.73 What is flip-flop? Explain the principle of operation of S-R flip-flop with
truth table.
(7)
Ans:
For a sequential system, we must know what has happened in the past. Therefore we
must have storage device to retain this information until we are ready to use it. The basic
unit of this storage is flip-flop. It is a device with two stages i.e., the output is either ‘0’
(logic 0) or +5V dc (logic 1).
A flip-flop maintains its output state until directed by an input signal to change its state.
This means that it can store 1-bit information.
S-R flip-flop:
It uses a pair of cross coupled transistors as shown in Fig. 36a. When, transistor T1 is in
saturation then its collector voltage is the base drive for transistor T2, i.e., no base drive
for T2. Hence T2 is cutoff and its collector voltage is approximately + VCC (logic 1).
This drives the base of T1 and thus T1 operates in saturation region.

R S Q
0 0 No change
0 1 1
1 0 0
1 1 Invalid

Fig. 36a

In effect T2 is OFF and T1 is ON making Q=1(+V CC). Similarly if T2 is in saturation T1
is OFF resulting Q=0. By introducing one input at the base of each transistor we can
control the state of operation of the transistor.

Q.74 Explain with a neat diagram the working of a BCD counter (7)

Ans:
BCD decade counter goes through a straight binary sequence from 0000 to 1001 state.
Then recycles back to 0000 state. The circuit of a BCD counter is given in fig.
States of BCD decade counter:
FlipFlop-A toggles on each clock pulse so that logic equation for its J and K inputs is

JA = KA = 1
Fig. – A BCD counter

This is implemented by connecting these inputs to a constant high level.
FlipFlop-B changes state on next clock pulse each time QA = 1 and QD = 1 so that
__
JB = KB = QAQD. __
This is implemented by ANDing QA and QD and connecting the gate output to JK inputs
of FlipFlop -B.

Clock QA QB QC QD
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1

FlipFlop-C changes on next clock pulse each time both QA = 1 and QB = 1
JC = KC =QAQB
This is implemented by ANDing QA and QB and connecting gate output to JK inputs
of FlipFlop F-C.
FlipFlop -D changes on next clock pulse each time QA = 1 and QB = 1, QC = 1 or when
QA = 1 and QD =1
JD = KD =QAQBQC+QAQD

Q.75 Draw the block schematic of a typical operational amplifier and briefly explain the
function of each block. Also give the equivalent circuit of the
opamp. (9)

Ans:
The block diagram of a typical opamp
Equivalent circuit of the opamp

The first –stage is double-ended high-gain differential amplifier. In this stage high-
gain is desirable so that there would be a negligible effect on the output of any
shortcoming in the following stages. Also this stage determines the input resistance of
the op-amp.
The second stage is usually another differential amplifier, which is driven by the
output of first stage. In most amplifiers the intermediate stage is dual input,
unbalanced output differential amplifier in order to increase the gain. In this amplifier
output is measured at the collector of only one of the two transistors with respect to
ground. In the quiescent condition some dc- voltage exists at the output terminal and
there is no other collector voltage at output to balance or nullify this output dc
voltage.
The third stage, known as level shifting stage, is usually an Emitter-follower circuit in
order to shift dc-level at the output of the intermediate stage downward to zero volts
with respect to ground. Here error signals is developed in the intermediate stage due
to direct coupling and gets amplified in the succeeding stages. This increase in dc-
level tends to shift the operating point of the succeeding stages which also limits the
output voltage swing or may distort the output signal.
The final stage is usually a push-pull complementary amplifier. This stage increases
the output voltage swing and current supplying capability of the amplifier. A well
designed output stage also provides low output resistance.

Q.76 Draw the circuit of a monostable multivibrator using op-amp. Describe its operation and
derive an expression for its pulse
period. (10)

Ans:
Monostable multivibrator circuit using op-amp can be drawn as in the Fig. 38a(i). The
circuit remains in its stable state until a triggering signal causes a transition to the quasi
stable state.

Fig. 38a(i)

At stable state Vo = + Vz and C is clamped at Vc = Vd = 0.7V.
By trigger of suitable duration and amplitude, output will switch to Vo = -VD. The
capacitor will charge through Rf towards +Vz as D1 becomes reverse
biased.
Fig. 38a(ii)

When Vc < - βVz, the comparator again swings back to +Vz and capacitor C will charge
towards +Vz until Vo = VD where ‘C’ will be clamped again at VD

Derivation:
Charging from VD to –Vz: Vc = -Vz + (VD + Vz) e-t/
Where τ = Rf C.
At t = T, Vc = -βVz. Hence – βVz = -Vz + (VD + Vz) e-T/
Solving for T, we get T = RfC ln [(VD+Vz)/ (Vz- βVz)] = RfC ln [(1 + VD/ Vz)/ 1-
β]

Q.77 Show how the monostable multivibrator circuit you have drawn can be converted to
astable type by simple changes in the monostable circuit. (4)

Ans:
Removing triggering circuit, D2 and D1 from the circuit shown in Q.76, we can convert
monostable multivibrator to astable multivibrator as shown in Fig. 38b.
Fig. 38b.

Q.78 Sketch the circuit of a bridge rectifier and describe its operation. Derive expressions for
rectification efficiency and ripple factor of the circuit. If a capacitor is added to the
circuit, show the output voltage waveform of the rectifier. (8)

Ans:
The bridge rectifier circuit is as shown in Fig. 39a(i).

Fig. 39a(i)

Operation: During positive half cycle of the input voltage point A becomes positive.
Diodes D1 and D2 will be forward biased and D3 and D4 reverse biased. D1 and
D2 conduct in series with the load and the current flows in the direction as shown in
figure1 by solid arrows.
In the next half cycle, when the polarity of the ac voltage reverses, ‘B’ becomes positive
D3 and D4 are forward biased, while D1 and D2 are reverse biased. D3 and D4 conduct in
series with the load and the current flows as shown by dotted arrows.
During both the half cycles of input signal, the current through R L is in same direction
and is as shown in Fig. 39a(ii).

Fig. 39a(ii)
Expression for efficiency and ripple factor:
iL = Im sin ωt 0  ωt  
iL = -Im sin ωt   ωt  2

Idc = (1/∫ Im sin ωt d(ωt)
0
Idc = 2Im /  and Edc = 2Em / 


In bridge rectifier, in each half cycle two diodes conduct simultaneously. Hence
maximum value of load current is

Im = Em / (Rs+2Rf+RL), where Rs = transformer secondary winding resistance.

PDC = IDC2RL = (2Im/) 2 RL

PAC = Irms2 (2Rf+Rs+RL) = (Im/2)2 (2Rf+Rs+RL)

[(4Im2/2) RL] 8RL
Therefore, rectification = PDC/PAC =
(since 2Rf+Rs<< RL)
efficiency Im2/2 (2Rf+Rs+RL) 2RL

= 8/2 = 81.05%

Ripple factor = (Irms/IDC) 2 – 1

= [(Im/2)/ (2Im/)] 2 – 1 =  (2/8) –1 = 0.48.

The Fig. 39a(iii) shows how a capacitor filter is connected to the rectifier output and the
output voltage waveform of the rectifier across the load, with capacitor filter.

Fig. 39a(iii)
Fig. 39a(iv)

The dotted line in Fig. 39a(iv) shows the rectifier output without filter and solid
line shows the output across the capacitor filter.
Q.79 Describe using a neat circuit diagram, the operation of a transistor series voltage
regulator.
(6)
Ans:
Fig. 39b shows the circuit of a transistor series voltage regulator.

Fig. 39b

In the above circuit, transistor behaves as an emitter follower. i.e it behaves as a variable
resistor whose value is determined by the base current. The load voltage V L is equal to
the difference of zener voltage (Vz) and the base to emitter voltage VBE.
i.e VL = Vz – VBE or VBE = Vz – VL
Any increase in VL decreases VBE as Vz is fixed. Therefore the forward bias of the
transistor is reduced, which reduces the level of conductance. Due to this V CE of
transistor increases which in turn slightly decreases the input current to compensate for
the increase in the value of load resistance, so load voltage may remain at a constant
value.

Q.80 Prepare the truth table for the output ‘F’ of the logic circuit shown in figure
below. Write also the canonical SOP expression for F.

Ans:
The truth table for the above expression is as shown below.
_ _ _
A B C A AC AB+AC BC (AB+AC)BC
B
0 0 0 0 0 0 0 0
0 0 1 0 1 1 0 0
0 1 0 0 0 0 0 0
0 1 1 0 1 1 1 1
1 0 0 0 0 0 0 0
1 0 1 0 0 0 0 0
1 1 0 1 0 1 0 0
1 1 1 1 0 1 1 1
The canonical SOP expression for F is found from 1’s in the 4th and 8th rows.
_
i.e. F (A,B,C) = ABC + ABC

Q.81 Write the logic diagram and truth table of clocked S-R flip flop and explain its operation.
What are the drawbacks of S-R flip flop? (6)

Ans:
Fig. 41a(i) shows clocked RS flip flop. It consists of a basic NOR gate and two AND
gates. The outputs of the two AND gates remain at ‘0’, regardless of the R and S inputs
as long as Cp=0.When the clock pulse goes to ‘1’, information from the R and S inputs
are allowed to reach the basic flip flop.

Fig.41a(i)

Fig. 41a(ii) shows truth table for clocked RS flip flop. The waveforms in Fig.
41a(iii) illustrate the operation of clocked RS flip
flop.
Fig. 41a(ii)
Drawbacks of SR flip-flop:
i) A 11 input (R =S =1) is not allowed as it will make both Q and = 1 while the
clock pulse is 1. The state of output will be unpredictable when Cp goes to ‘0’.
ii) While clock pulse is 1, change in inputs changes the output.

Fig. 41a(iii)

Q.82 Construct a 4-bit binary ripple counter using suitable flip-flop and describe its
working?
(6)
Ans:
Fig. 41b shows the circuits of a 4-bit ripple counter consisting of edge-triggered flip-flop
(JK).
Fig. 41b

In this ripple or asynchronous counter, the clocking for all flip-flops except the one at
the LSB is obtained by the transition of the flip-flop at the previous stage. By keeping
J=K= 1 all flip flop’s are ready to change state at the arrival of clock pulse which is
effective only when a transition from 1 to 0 takes place. Flip-flops as shown are
sensitive to negative edge of clock signal. The output of one stage acts as a clock to the
next stage. For each negative transition of a clock, Q 0 changes its state. Q1 changes its
state for every 1 to 0 transition of Q 0. Q2 changes its state for every 1 to 0 transition of
Q1. Similarly Q3 changes its state for every 1 to 0 transition of Q 2. The truth table is as
follows:
Clk Q3 Q2 Q1 Q0
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1
10 1 0 1 0
11 1 0 1 1
12 1 1 0 0
13 1 1 0 1
Clk Q3 Q2 Q1 Q0
14 1 1 1 0
15 1 1 1 1

Q.83 What is ‘doping’ of a semiconductor? Explain how p- and n-type semiconductors are
formed. Also write their energy band diagrams, clearly showing the different energy
levels. (8)

Ans: pp 102 -
104

Q.84 What is Early effect? Explain how it affects the characteristics of BJT in CB
configuration.

(8)
Ans: p. 238 - 39

Q.85 Draw a neat circuit of a differential amplifier and explain its
operation. (8)

Ans: p. 450 – 52

Q.86 Explain the effect of temperature on a
JFET. (8)

Ans: p. 276.

Q.87 Describe how oscillations are developed in a tank circuit.

Ans: p. 655

Q.88 Define the following terms as applied to
characterisation of opamps.
(i) CMRR (ii) slew rate

Ans: p. 800, p. 826

Q.89 Draw a neat diagram to show the functional
blocks of a complete regulated power supply. Explain the role of each
block. (9)

Ans: p. 908 – 09.

Q.90 Draw the circuit of 4-bit ring counter using
suitable flip-flop. Explain its operation using timing diagrams and truth
table. (8)

Ans: p. 1021

Q.91 Show how a T-flop-flop can be constructed
using J-K flip-flop. Write the truth table of T flip-
flop. (2)

Ans: p. 1016

Q.92 Distinguish between avalanche and zener
breakdown in p-n junction diode. (7)

Ans:
Both avalanche breakdown and zener breakdown occur under reverse biased
condition of p-n junction and the common cause is the electric field accelerating a
carrier which collides with an ion and breaks the covalent bond releasing one or more
extra carriers. In the case of avalanche breakdown, the carriers are thermally
generated ones accelerating under externally applied large electric field in reverse
bias and the process is cumulative giving rise to more and more pairs of carriers by
multiple collision of ions. The result is destructive.
On the other hand, in a zener diode, the breaking of ionic bond and generation of
extra carriers is by the intense electric field across a very narrow depletion region at
the junction, due mainly to rather heavy doping of both p and n regions of the diode.
The resulting process gives rise to large reverse current and is reversible. This
phenomenon is called ‘Zener breakdown’.

Q.93 Draw the circuit of Darlington amplifier and analyse it to obtain expressions for its
current gain and input impedance. Also mention its merits and
application. (10)

Ans: The circuit for Darlington amplifier is shown below
The equivalent circuit for small signal is as shown below
Considering ……(1)
Current Gain: …..(2)
For transistor Q1, 1/hoel is comparable with becomes the load impedance for Q1.
Hence without neglecting 1/hoel, the current gain for Q1 is
……(3)

If , equation (3) can be written as

The overall gain of the amplifier is
i.e., …….
(4)
For , a good approximation would be ignored w.r.t Zin 2, …..
(5)
Input impedance
=
If then

if , then
The advantage of darlington amplifier is its very high current gain and very high Zin. It
is used to isolate high impedance source from low impedance load.

Q.94 Draw the circuit of common source amplifier using JFET and show its equivalent circuit.
Analyse the equivalent circuit to find an expression for voltage gain and output
resistance.

(6)
Ans:
The circuit of n-channel, JFET common source amplifier is shown below in fig(1)
and its ac equivalent circuit is shown in fig(2).

Fig(2) shows current source equivalent circuit where gm Vi represents controlled
source and rd represents the incremental drain resistance. The output impedance Zout
of the amplifier is given by the parallel combination of rd RD
i.e.
The voltage gain is found as follows:

The voltage gain,

Or .

Q.95 For an amplifier having open loop gain A, find an expression for gain with negative
feedback of feedback ratio β. Show how stabilization of gain of an amplifier is achieved
with negative feedback. (6)

Ans:
An amplifier block without any feedback is shown in fig(1). If to this amplifier
negative(voltage) feedback is provided, the situation is shown in fig(2).

Fig(1)

Fig(2)

In the basic amplifier, the gain is A i.e. which is now called the open
loop gain. In fig(2), it is shown that a fraction of the output voltage (i.e. ) is
added negatively (i.e.
negative feedback) to the signal input Vi so that the actual input to the basic amplifier
is . Thus by the basic amplifier characteristic
,i.e.
i.e. AVi = Vo (1+Aβ) or

where Af is the gain with negative feedback
i.e.
Gain stability with negative feedback consider the expression for Af
i.e.
…………(1)
Differentiating this expression w.r.t. A

Now divide this expression by (1)
Then
This shows that though the per unit change in the gain of the basic amplifier is ,
the change in the gain of the overall amplifier with negative feedback is times
the same. Generally Hence considerable improvement in gain stability is
effected by negative feedback.

Q.96 Show an FET source follower circuit. What type of negative feedback takes place in the
circuit? Analyse the circuit to derive an expression for voltage gain with
feedback. (6)

Ans:
An FET source – follower circuit is shown below. Its equivalent circuit for analysis is
also shown.

The sampled signal is the voltage across R which is fully fed back. Hence this is a
case of voltage series feedback.
To identify the basic amplifier without feedback, let V o = 0. Then Vi appears across G
and S. The output circuit is found by setting Ii = 0. Then R is present only in the
output circuit. Thus the basic amplifier is shown in fig (2).
The equivalent circuit, by replacing the FET by its low frequency model, is shown in
fig(3).
It is seen that Vf and Vo are equal. Hence

The gain of the basic amplifier is (as )
………….(1)
where
using the general relation in a –ve f.b. amplifier
i.e. the gain with f.b. in the source follower is
i.e. …….(2) the expression for gain of the source follower.

Q.97 Explain the principle underlying the working of R-C oscillators. Mention the
applications of R-C oscillators. (7)

Ans:
The general requirement for producing oscillations in an amplifier is to provide
positive feedback so that feedback voltage is in phase with the input to the amplifier.
This means there should be 2π shift in phase from input through the output and back
at input. As an inverting amplifier provides π (180 0) phase shift, it can be used along
with a phase shifting network that provides further π (180 0) shift at the desired
frequencies as shown in the block schematic below.
Typically, for phase shift, RC networks may be used as shown in figure. The R’s and
C’s must be so chosen as to produce 1800 shift at the frequency of oscillation
required.
It is also necessary that the output impedance of the phase shift network must be
much smaller than the input impedance of the amplifier. All these, essentially mean
that Barkhausen criterion of unity loop gain i.e. –Aβ = 1, is network, which also
means that there should be positive feedback to the basic amplifier.
Application: RC oscillators are commonly used as audio oscillators.

Q.98 Draw the circuit of sample and hold using op-amp and explain its
operation. (9)

Ans:
A sample – and – hold circuit is essentially a switch in series with a capacitor, as in
fig(1)

fig(1) S/H Control voltage Fig(2)

The voltage across the capacitor C tracks the input signal V i during the time TON,
when a logic control closes the switch S. The capacitor holds the instantaneous value
developed on C at the end of T on, when the control opens S. The switch may be a
relay, a diode bridge gate, a BJT or a MOSFET controlled by a gating signal.
A S/H circuit using op – amp and an n-channel enhancement MOSFET is shown in
fig(2). The analog signal Vi to be sampled is to be applied at the drain terminal of the
E-MOSFET and a pulse train is applied at the gate, the MOSFET connects the drain
to the source so that V in is applied across the capacitor during the time the pulse is
present. The action of the switch and the capacitor are illustrated in the timing
diagram in fig(3).
fig(3)

During the time the MOSFET is ON, the Vi appears across the capacitor and so at the
output of the non-inverting amplifier as Vo. When MOSFET is off during TOFF, the
input is isolated from C and thee op-amp circuit. During this time, the voltage on C
will be held constant at a value of V i, which prevailed at the end of T ON. The TON is
often called the ‘sample period’ and the TOFF the ‘hold period’. To obtain an output
that closely approximates the input, the frequency of the control voltage at the gate
should be as large as possible. To retain the sampled voltage without loss, the
capacitor should be of very good quality with the least charge leakage.

Q.99 Write a neat circuit diagram of saw-tooth wave generator using op-amps and describe its
operation. Derive an expression for the frequency of the wave. (10)

Ans:
The circuit of triangular – wave generator using two op – amps is shown in the figure
below

The operation of the circuit is explained with reference to the wave diagram shown
below.

The Zener diodes will clamp the voltage Vi at either + Vz or – Vz depending on the
polarity of the saturation voltage at the output of the comparator.
To begin with say V1 = + Vz at t = to
The integrator causes charging of capacitor C and Vo(t) will be a ramp with negative
slope.
The current into C is I = and Vo(t) is given by
……………(1)
Now the voltage Vz(t) is found by using superposition

When Vz(t) reaches zero at t = t 1, the comparator output changes to V1 = -Vz. Using
equation(2) to find Vo(t1),

i.e. ………….(3)
The direction of current into the integrator will reverse from t1 until t2 and is given by

During t2 > t > t1 the Vo(t) will be a positive going ramp. At t2 the output is
…………..(4)
as this value is limited by +Vz
At t2, the comparator switches its output again and the cycle repeats.
Derivation of expression for the frequency:
As seen by the analysis above and as shown in the wave diagram,

and at , as at equation (3)
Now using equation(1),
Hence by equation I =

Assuming matched zener diodes i.e.
We get equal magnitudes of +ve and –ve ramps
Hence the period T =
The frequency of triangular waveform is therefore, f =

Q.100 Explain how an astable multivibrator can be implemented using 555 timer
IC. (6)

Ans:
The connections to be made to the 555 timer IC chip and the relevant internal details
are shown in the figure(1) below.

fig(1)
fig(2)
At the non-inverting inputs of comparators, the potential division of V cc across the
R’s causes . The Vcc also charges C through RA and RB.
Assume that at t = 0, Vc = V2, which causes comp 1 output to be high and Q output of
the latch is in reset condition, which in turn makes volts, as shown in fig 2. At
the same time, as , the transistor Q1 is ‘on’ causing gradual discharge of C
through RB. At t = T1, let the value of Vc which is also ‘threshold voltage’ of the
timer, be V1. This will cause the output of comparator 2 to be high and thus setting
the latch. The transistor Q1 is now cut off . This leads to charging of C again
and gradual rise in V0 as shown in figure 2. At , again which causes
repetition of cycle of events described above. The duration of T1 and T2 are given
by and .
The frequency of oscillation is .

Q.101 Why filters are used along with rectifiers in the construction of a power supply? List the
filter types used in power supplies. Explain their effect on rectifier output
waveforms. (10)

Ans:
Necessity of filters for rectifiers:
The output from any basic rectifiers is not a pure d.c. There would be considerable
a.c. component in their output, called ‘ripple’, in addition to the
desired d.c. component. Most sophisticated electronic systems need pure d.c. supply
to drive, or power them. To construct a good power supply which gives
pure d.c. output, we need to remove or filter out the a.c. component from the output
of rectifiers. The output from basic rectifiers which contain a.c. component or ripple,
is fed to filter circuits so that the output from the filter is pure d.c. This situation is
illustrated in the figure below.

fig(1)

Following are the commonly used filter types are:
(i) Capacitor filter (ii) Series inductor filter (iii) Choke input filter (iv) π-filter (v) RC
filter.
Their effect on rectifier output waveforms are explained below.
(i) Capacitor filter:
It is connected in shunt or parallel with the load as shown in the fig (1)
fig(2) fig(3)
This is the simplest and the least expensive filter. A large value capacitor offers high
impedance to d.c. Fig(3) shows how the capacitor helps in maintaining the load
voltage as constant as possible. In the case of a full-wave rectifier without filter, the
load voltage would also be the rectified waveform shown by the dotted line. But with
C filter, the voltage across the load has much less ripple as shown by the full line
trace.
(ii) Series Inductor filter:
Property of an inductor is to oppose any change in the current through it. An inductor
can be connected to act as a filter between the load and a basic rectifier as shown in
fig(4).

fig(4) fig(5)

The inductor or choke stores energy in its magnetic field when the current is above an
average value. The stored energy is released when the load current falls below the
average value. The effect of the inductor filter is illustrated in fig 5 above.
(iii) Choke Input filter (L–Section filter):
As explained above in connection with inductor filter and capacitor filter, while
capacitor acts to keep the voltage across itself constant and inductor acts to keep the
current through it constant, the advantages of the properties of both an inductor and a
capacitor are combined into an L-Section filter shown in fig 6.
C

fig(6) fig(7)

The effect of the L-Section filter is illustrated in fig 7. This provides d.c. output more
ripple free than either C-filter alone or choke filter alone.
(iv) π-filter: The circuit of π-filter is shown in fig 8.

fig(8) fig(9)

Because of the additional capacitor at the input of the filter, the d.c. output is of a
higher value and more ripple-free than is possible by any of the filters discussed
earlier. The effect of the filter on a full-wave rectifier output is illustrated in fig 9.
(v) RC-Filter: The RC filter circuit is shown in fig 10.
fig(10) fig(11)

The disadvantages of the π-filter are its bulk, weight and higher cost. In place of L, if
resistor R is used, the effect is almost similar to that obtained from π-filter. However,
the R being dissipative of energy, the overall efficiency of the power supply will be
less than possible with π-section filter. Also the ripple factor in this case would be
poorer than in a π-section filter where an inductor is used.

Q.102 Delineate the concept of ‘duality’ in Boolean algebra. (3)

Ans:
It is the property of Boolean algebra that for a given Boolean expression there always
exists a dual. Stated succinctly
Two Boolean will be called “duals” if they differ only by the

simultaneous interchange of AND for OR and “0” for “1”
All postulates, theorems and axioms of Boolean algebra are to be stated in pairs, one
statement being the dual of the other statement.
e.g.: The expression x + xy = x which is law of absorption has a dual x(x + y) = x.

Dual logic tables:
Table for ‘OR” Table for ‘AND’

If the ‘I’ are replaced by ‘0’
we get the table for AND as
shown on right side

Dual – K – maps

Dual K maps
Consider a function f = AC + BC + BD. The K-map for this function is

fig (1) fig (2)

If a dual map is drawn by replacing ‘1’ by ‘0’ and ‘0’ by ‘1’ as shown in, and if we
simplify the function represented by the map, we get the expression

= CD + CB +
which is the dual function f = AC + + BD

Q.103 For the function, F(A,B,C) = Σ (1,5,7), write the canonical POS and SOP
expressions. (2)

Ans:
Canonical SOP form is directly obtained for

i.e. --------- canonical SOP expression.

POS expression is obtained as product of maxterms
i.e. F(A,B,C) = π (0,2,3,4,6)
i.e.
which is canonical POS expression.

Q.104 Write the logic diagram of a clocked R-S flip-flop using only NAND gates. Explain its
operation with reference to truth
table. (6)

Ans:
The logic diagram of a clocked S-R flip-flop based on NAND gates only is shown in
the figure below
Clocked S-R flip-flop

The gates 1 and 2 form the latch and the fates 3 and 4 are control or steering fates.
When the clock is low of CK = 0, the outputs of both the gates are ‘1’ irrespective of
the values of S and R. The outputs Q and remain as they were, i.e. the flip-flop
does not change state during CK = 0. Now let the CK = 1. We examine the operation
for the four different combinations of S and R. For S = 0, R = 0, the outputs of 3 and
4 are 1. If Q were to be ‘0’ (and = 1) there will not be change in the value of Q or
the state of the flip-flop. This is indicated in the truth-table, at the first row.
For S = 1, R = 1, the inputs to 1 and 2 will be A 1 = B1 =0, and A2 = B2 = 1. For these
inputs the Q is 1. That is, even if Q were to be 0 before clock is active, it will be
forced to be 1. This action is called ‘setting’ the flip-flop and is indicated at the
second row of the truth-table.
Next for S = 0, R = 1, the condition is seen to be the opposite of the one that prevailed
when S = 1; R = 0.
Thus Q will be forced to be at logical zero and = 1. This is indicated at the third
row of the truth-table.
For S = 1, R = 1, the outputs from both 3 and 4 are zero and therefore the outputs of
the both the gates 1 and 2 are ‘1’. This condition is logically inconsistent. Hence the
state of the flip-flop is unidentified or indeterminate. Therefore, S = R = 1 input
combination is forbidden, which is indicated in the fourth row of the truth-table.

Q.105 Write the truth table for full adder and show its implementation using
gates. (5)

Ans:
The requirement of a full adder is indicated in the block shown below.
Truth-table

A full adder is required to perform addition of added and augend bits at the same
digit position of two binary numbers, taking into account any carry resulting from the
lower digit position. Thus considering all the possible combinations for the augend(
), addend ( ) and carry( ) inputs, the truth-table is drawn to obtain the
required ‘sum’ and ‘carry’ outputs, as shown above.
From the truth-table, the Boolean expressions for Sn and Cn are given by

Sn = AnBnCn-1 + AnBnCn+1+ AnBnCn-1 + AnBnCn-1
This cannot be simplified any further.
For finding simplified expression for Cn, a k-map is drawn as below

k-map for Cn
from the map
Cn = AnBn + AnCn-1 + BnCn-1
The implementations of Sn and Cn are shown by the AND – OR logic below

Q.106 In an astable multivibrator, the base registers are of 12.5 K ohm and the capacitors are
of 0.01 µ ohm. Determine the PRR (pulse repetition rate).

Ans: 5772 pulses per second.

Q.107 A single-phase full-wave rectifier uses two diodes, the internal resistance of each
being 20Ω. The transformer rms secondary voltage from centre tap to each end of
secondary is 50V and load resistance is 980Ω. Find
(i) the mean load current. (ii) rms load current and output
efficiency. (8)

Ans: (i) 45 mA (ii) 50 mA (iii) 79.58 %

Q.108 Simplify the following expression using Boolean algebra technique
Z = AB + A(B + C) + B(B + C) (8)

Ans: B + AC
Z = AB + A(B + C) + B(B + C)
= AB + AB + AC + BB + BC
= AB + AC + B(1+C) ( A + A = A and B + B = B )
= AB + AC + B(1+C)
= AB + AC + B ( 1+A = 1 AND B +1 = B)
= B + AB + AC
= B(1+A) + AC ( 1 + A = 1 and B + 1 = B)
= B + AC

Objective Electronics

Uploaded by

Copyright:

Available Formats

Objective Electronics

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Objective Electronics

Uploaded by

Copyright:

Available Formats

What are the different types of breakdown mechanisms in a p-n junction?

What are the different types of breakdown mechanisms in a p-n junction?

How does an op-amp integrator respond to a step input?

How does an op-amp integrator respond to a step input?

TYPICAL QUESTIONS & ANSWERS

(A) The current through R1 will increase.

(C) a constant frequency. (D) d.c

Turns ratio and impedances:

Turns ration and voltages:

= average current.

(ii) DC power output = watts.

(iv) Rectification Effect = .

The current relationship in a transistor is given by

……(1) ………(2)

using equation (6),

using equation (7),

given A = 1000 and β = 2.5 x 10-3,

; given: Vmax = 50volts; RL = 400Ω, RF = 30 Ω

i.e. or 75.5%.

Monostable Multivibrator Circuit

Power drawn from the source, .

Tail current,

And Tail current,

DC or static resistance,

The pulse width

i.e. 40.6 % if RF is neglected.

Density of charge carriers = σμ

Rb = (R1R2) / (R1+R2) = (1.5x103x3x103) / (1.5+3)103 = 1kΩ

Fig 24 a (i) Fig 24 a (ii)

(ii) If Vo = 0, then R1 || R2.

Diffusion capacitance is given by the equation, where dQ represents the

We know that

So diffusion capacitance

For a forward bias,

CE – Amplifier n – parameter Equivalent circuit with RE.

Operation of N-Channel E-MOSFET

For an open-loop amplifier,

An astable multivibrator, often called a free-running multivibrator, is a rectangular-

Eventually, the threshold voltage exceeds + , comparator 1 has a high output

The continuity equation states a condition of

within the volume and decrease within the volume = ------(1)

Increase within the volume =

Under these conditions .

So from the equation (5), we have ------(7)

Over-all voltage gain, .

Here , and

Current Mirror Circuit

Trigger Input, Output and Capacitor Voltage Wave Forms

Internal Circuitry with external connections

capacitor voltage becomes slightly greater than , the output of comparator-1

The circuit’s frequency of oscillation is dependable on the charge and discharge of a

Logic diagram of 3 bit UP – DOWN Counter

Now electric field, or

Input waveform Negative Clamper Output waveform

So current gain,

So current gain,

Thevenin’s Equivalent circuit for low frequency range

So current gain,

So voltage gain