Lit Quick Start Guide

Quick Start Guide
00825-0100-4530, Rev HA
February 2019
Rosemount™ 5300 Level Transmitter
Guided Wave Radar

Quick Start Guide February 2019
Contents
About this guide............................................ 3 Configure.....................................................22
®
Confirm system readiness (HART only).........5 Safety Instrumented Systems (4-20 mA only)..
25
Mount transmitter on tank.............................6
Adjust probe length..................................... 26
Prepare the electrical connections............... 11
Product certifications...................................29
Connect wiring and power up...................... 19
2 Rosemount 5300 Level Transmitter

February 2019 Quick Start Guide
1 About this guide

This Quick Start Guide provides basic guidelines for the Rosemount 5300
Level Transmitter. Refer to the Rosemount 5300 Reference Manual for more
instructions. The manual and this guide are also available electronically on
Emerson.com/Rosemount.
WARNING
Failure to follow safe installation and servicing guidelines could result in death
or serious injury.
• Make sure the transmitter is installed by qualified personnel and in
accordance with applicable code of practice.
• Use the equipment only as specified in this Quick Start Guide and the
Reference Manual. Failure to do so may impair the protection provided by
the equipment.
• Any substitution of non-recognized parts may jeopardize safety. Repair,
e.g. substitution of components etc., may also jeopardize safety and is
under no circumstances allowed.
Explosions could result in death or serious injury.
• Verify that the operating atmosphere of the transmitter is consistent with
the appropriate hazardous locations certifications.
• To prevent ignition of flammable or combustible atmospheres, disconnect
power before servicing.
• Before connecting a handheld communicator in an explosive atmosphere,
ensure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
• To avoid process leaks, only use the O-ring designed to seal with the
corresponding flange adapter.
Electrical shock could cause death or serious injury.
• Avoid contact with the leads and terminals. High voltage that may be
present on leads can cause electrical shock.
• Make sure the mains power to the transmitter is off and the lines to any
other external power source are disconnected or not powered while
wiring the transmitter.
• Ground device on non-metallic tanks (e.g. fiberglass tanks) to prevent
electrostatic charge build-up.
Quick Start Guide 3

WARNING
Probes with non-conducting surfaces
• Probes covered with plastic and/or with plastic discs may generate an
ignition-capable level of electrostatic charge under certain extreme
conditions. Therefore, when the probe is used in a potentially explosive
atmosphere, appropriate measures must be taken to prevent electrostatic
discharge.
Eliminate the risk of ESD discharge prior to dismounting the transmitter head
from the probe.
• Probes may generate an ignition-capable level of electrostatic charge
under extreme conditions. During any type of installation or maintenance
in a potentially explosive atmosphere, the responsible person should
make sure that any ESD risks are eliminated before attempting to separate
the probe from the transmitter head.

2 Confirm system readiness (HART® only)

2.1 Confirm HART® revision capability
If using HART based control or asset management systems, confirm the HART
capability of those systems prior to transmitter installation. Not all systems
are capable of communicating with HART Revision 7 protocol.
Transmitters with a firmware version 2F0 or later can be configured for either
HART Revision 5 or 7.
2.2 Confirm correct device driver

Procedure
• Verify that the latest Device Driver (DD/DTM™) is loaded on your systems
to ensure proper communication. See Table 2-1.
• Download the latest Device Driver from Emerson.com/DeviceInstallKits.
Table 2-1: Rosemount 5300 Device Revisions and Files
Firmware version (1) Find Device Driver
HART® Universal Device Revision (2)

Revision
2F0 or later 7 4
5 3
2A2 - 2E0 5 3
(1) Firmware version is printed on the transmitter head label, e.g. SW 2E0 or can
be found in Rosemount Radar Master (select Device > Properties).
(2) Device revision is printed on the transmitter head label, e.g. HART Dev Rev 4.
2.3 Switch HART® revision mode

If the HART configuration tool is not capable of communicating with HART
Revision 7, the device will load a generic menu with limited capability. To
switch the HART revision mode from the generic menu:
Procedure
1. Locate the “Message” field.
2. In the Message field, enter HART5 or HART7 and then 27 trailing
spaces.
Quick Start Guide 5

3 Mount transmitter on tank

For flexible single lead probes ordered with weight unmounted (option code
WU), refer to Adjust probe length before mounting the transmitter.
3.1 Threaded/Flange/Tri-Clamp® tank connection

Procedure
1. Seal and protect the threads.
Only for NPT threaded tank connection.
Use anti-seize paste or PTFE tape according to your site procedures.
2. Mount the device on tank.

$ %
&
A. NPT
B. Flange
C. Gasket

$ %
& &
A. Tri-Clamp
B. BSP/G
C. Gasket
3. (Optional) Adjust display orientation.
4. Tighten the nut.
Torque 30 ft-lb (40 Nm)
Quick Start Guide 7

3.2 Install remote housing

Procedure
1. Carefully remove the transmitter.
2. Mount the probe on tank.
A. Gasket
3. Mount the remote connection on the probe.

4. Mount the bracket to the pipe.

$
4X
%
A. Horizontal pipe
B. Vertical pipe
5. Fasten the housing support.
3X
6. Mount the transmitter head.
Quick Start Guide 9

3.3 Bracket mounting

Procedure
1. Mount the bracket to the pipe/wall.
On pipe:
$
4X
%
A. Horizontal pipe
B. Vertical pipe
On wall:
4X
2. Mount the transmitter with probe to the bracket.
3X

4 Prepare the electrical connections
4.1 Cable gland/conduit

For explosion-proof/flameproof installations, only use cable glands or conduit
entry devices certified explosion-proof or flameproof.
4.2 Power supply (Vdc)

Approval type HART® FOUNDATION™ RS-485 with
Fieldbus Modbus®
None 16-42.4 9-32 8-30 (max. rating)
Non-sparking/ 16-42.4 9-32 N/A

energy limited
Intrinsically safe 16-30 9-30 N/A
FISCO N/A 9-17.5 N/A
Explosion-proof/ 20-42.4 16-32 8-30 (max. rating)

Flameproof
Quick Start Guide 11

4.3 4-20 mA/HART® communication

4.3.1 Wiring diagram
Figure 4-1: Wiring Diagram for 4-20 mA/HART®
&
' )
- - -
+ + +
(
%
A. Handheld communicator
B. Approved IS barrier (for Intrinsically Safe installations only)
C. HART modem
D. Current meter
E. Load resistance (≥250 Ω)
F. Power supply
Note
Rosemount 5300 Level Transmitters with flameproof/explosion-proof output
have a built-in barrier; no external barrier needed.
4.3.2 Load limitations

For HART® communication, a minimum loop resistance of 250 Ω is required.
Maximum loop resistance is determined by the voltage level of the external
power supply, as given by the following diagrams:

Figure 4-2: Intrinsically Safe Installations

$

&

%
A. Loop Resistance (Ohms)

B. External Power Supply Voltage (Vdc)
C. Operating region
Figure 4-3: Non-Hazardous and Non-Sparking/Energy Limited

Installations

$
&

%

C. Operating region

Figure 4-4: Explosion-Proof /Flameproof (Ex d) Installations

$
&

%

C. Operating region
Note
For the Ex d case, the diagram is only valid if the load resistance is at the + side
and if the - side is grounded, otherwise the maximum load resistance is
limited to 435 Ω.

4.4 FOUNDATION™ Fieldbus

Figure 4-5: Wiring Diagram for FOUNDATION Fieldbus
&
+ + + '
- - -
A. Handheld communicator
B. Approved IS barrier (for Intrinsically Safe installations only)
C. FOUNDATION Fieldbus modem
D. Power supply
Note
Rosemount 5300 Level Transmitters with flameproof/explosion-proof output
have a built-in barrier; no external barrier needed.
4.5 RS-485 with Modbus® communication

See the Rosemount 5300 Reference Manual for details.
4.5.1 Power consumption

• < 0.5 W (with HART address=1)
• < 1.2 W (incl. four HART slaves)

Figure 4-6: Wiring Diagram for RS-485 with Modbus®
)
*
+
- (
$
& ' &
%
A. “A” line
B. “B” line
C. 120 Ω
D. RS-485 Bus
E. Power supply
F. HART -
G. HART +
H. If it is the last transmitter on the bus, connect the 120 Ω termination
resistor.
Note
Rosemount 5300 Level Transmitters with Flameproof/Explosion-proof output
have a built-in barrier; no external barrier needed.(1)
4.6 Grounding
Make sure grounding is done (including IS ground inside Terminal
compartment) according to Hazardous Locations Certifications, national and
local electrical codes.
(1) An external galvanic isolator is always recommended to be used for Flameproof/

Explosion-proof installations.

Note
Grounding the transmitter via threaded conduit connection may not provide
sufficient ground.
Note
In the explosion-proof/flameproof version, the electronics is grounded via the
transmitter housing. After installation and commissioning make sure that no
ground currents exist due to high ground potential differences in the
installation.
Transmitter housing grounding

The most effective transmitter housing grounding method is a direct
connection to earth ground with minimal (< 1 Ω) impedance. There are two
grounding screw connections provided (see Figure 4-7).
Figure 4-7: Ground Screws
A. Internal ground screw

B. External ground screw
Signal cable shield grounding

Make sure the instrument cable shield is:
• trimmed close and insulated from touching the transmitter housing.
• continuously connected throughout the segment.
• connected to a good earth ground at the power supply end.

Figure 4-8: Cable Shield
%
%
$
&
& &
'
A. Insulate shield
B. Minimize distance
C. Trim shield and insulate
D. Connect shield back to the power supply ground

5 Connect wiring and power up

Procedure
1. Make sure the power supply is switched off.
2. Remove the terminal block cover.
3. Remove the plastic plugs.
4. Pull the cable through the cable gland/conduit.
Adapters are required if M20 glands are used.

5. Connect the cable wires (see Figure 4-1, Figure 4-5, and Figure 4-6).
6. Ensure proper grounding (see Grounding).
7. Use the enclosed metal plug to seal any unused port.
Note
Apply PTFE tape or other sealant to the threads.
8. Tighten the cable gland.

Note
Apply PTFE tape or other sealant to the threads.
Note
Make sure to arrange the wiring with a drip loop.

9. Mount the cover making sure the cover is secure to meet explosion-
proof requirements.
10. Turn the jam screw counterclockwise until it contacts the cover.
Required for Flameproof installations only.
11. Connect the power supply.

6 Configure
Basic configuration can easily be done either with Rosemount Radar Master, a
handheld communicator, AMS Device Manager, DeltaV™, or any other DD
(Device Description) or DTM™ compatible host system. For advanced
configuration features, Rosemount Radar Master is recommended.
6.1 Configure using Rosemount Radar Master

Procedure
1. Start Rosemount Radar Master.
2. Connect to the desired transmitter.
3. In the Guided Setup window, click Run Wizard for guided setup and
follow the instructions.
4. In the Guided Setup window, continue with steps 2 to 5.

5. Click View live values from device to verify that the transmitter works
correctly.
6.2 Configure using AMS Device Manager or handheld

communicator
6.2.1 Connect to device using AMS Device Manager
Procedure
1. Start AMS Device Manager.
2. Select View > Device Connection View.

3. In the Device Connection View, double-click the modem icon.

4. Double-click the device icon.
6.2.2 Connect to device using a handheld communicator

Procedure
Turn on the handheld communicator and connect to the device.
6.2.3 Configure device

HART® Device Revision 3
Procedure
1. Select Configure/Setup > Basic Setup.
2. Configure steps 1- 6 in the Basic Setup (Variable Mapping, Probe,
Geometry, Environment, Volume, and Analog Out).
3. Select Finish.
4. Select Device Specific Setup.
5. Select Restart Device.
HART® Device Revision 4

Procedure
1. Select Configure > Guided Setup.
2. Select Level Measurement Setup and follow the instructions.
4. Run Verify Level to check your level measurement.
5. Consider optional setup, such as Volume and Display.
FOUNDATION™ Fieldbus
Procedure
1. Select Configure > Guided Setup.
2. Select Level Measurement Setup and follow the instructions.
3. (Optional) Select Volume Calculation Setup.
5. Select Restart Measurement.

6.3 FOUNDATION™ Fieldbus parameters

Table 6-1: FOUNDATION Fieldbus Parameters
Function Parameter
Probe type TRANSDUCER_1100 > PROBE_TYPE
Probe length TRANSDUCER_1100 > PROBE_LENGTH
Hold off distance/Upper null zone TRANSDUCER_1100 >

GEOM_HOLD_OFF_DIST
Tank height TRANSDUCER_1100 >

GEOM_TANK_HEIGHT
Mounting type TRANSDUCER_1100 > MOUNTING_TYPE
Pipe/chamber/nozzle inner diameter TRANSDUCER_1100 > PIPE_DIAMETER
Nozzle height TRANSDUCER_1100 > NOZZLE_HEIGHT
Measurement mode TRANSDUCER_1100 > MEAS_MODE
Product dielectric range (1) TRANSDUCER 1100 >

PRODUCT_DIELEC_RANGE
Upper product dielectric constant (2) TRANSDUCER 1100 >

UPPER_PRODUCT_DC
Process condition (rapid level changes) TRANSDUCER_1100 >

ENV_ENVIRONMENT
Volume calculation method TRANSDUCER 1300 >

VOL_VOLUME_CALC_METHOD
Tank diameter (only for ideal tank shapes) TRANSDUCER 1300 >
VOL_IDEAL_DIAMETER
Tank length/height (only for ideal tank TRANSDUCER_1300 >

shapes) VOL_IDEAL_LENGTH
Volume offset TRANSDUCER_1300 >

VOL_VOLUME_OFFSET
(1) Applicable to “Liquid Product Level” and “Solid Product Level” measurement
modes.
(2) Applicable to “Interface Level with submerged” and “Product Level and Interface
Level” measurement modes.

7 Safety Instrumented Systems (4-20 mA only)

For Safety Certified installations, refer to the Rosemount 5300 Reference
Manual.

8 Adjust probe length

This section describes how to adjust the length of flexible single lead probes
with weight unmounted (option code WU). For other probe types, refer to
Section 3 in the Rosemount 5300 Reference Manual.
Procedure
1. Measure tank height.
Tank height (H):
2. Calculate total probe length.

Total probe length (LTOT) = Tank height (H) – 2 in. (5 cm)
Total probe length (LTOT):
/727
A. 2 in. (5 cm) clearance

3. Mark where to cut the probe.
0
1
2
3
4
5
6
7
8
4. Slide the weight up.
5. Cut the probe at the mark.

6. Fasten the weight.
Weight material Torque (Nm)
Stainless steel 5
Alloy C-276 2.5
Alloy 400 2.5
Duplex 2205 2.5
7. Update transmitter configuration to the new probe length.
Probe length (L):

9 Product certifications
Rev 9.17
9.1 European directive information

The EU Declaration of Conformity for all applicable European directives for
this product can be found on EU Declaration of Conformity. The most current
revision is available at Emerson.com/Rosemount.
9.2 Safety Instrumented Systems (SIS)

SIL 3 Capable: IEC 61508 certified for use in safety instrumented systems up to
SIL 3 (Minimum requirement of single use (1oo1) for SIL 2 and redundant use
(1oo2) for SIL 3).
9.3 Ordinary location certification

As standard, the transmitter has been examined and tested to determine that
the design meets the basic electrical, mechanical, and fire protection
requirements by a nationally recognized test laboratory (NRTL) as accredited
by the Federal Occupational Safety and Health Administration (OSHA).
9.4 Installing equipment in North America

The US National Electrical Code® (NEC) and the Canadian Electrical Code (CEC)
permit the use of Division marked equipment in Zones and Zone marked
equipment in Divisions. The markings must be suitable for the area
classification, gas, and temperature class. This information is clearly defined in
the respective codes.
9.5 USA
9.5.1 E5 Explosionproof (XP), Dust-Ignitionproof (DIP)
Certificate FM16US0444X
Standards FM Class 3600 – 2011; FM Class 3610 – 2010; FM Class 3611 –
2004; FM Class 3615 – 2006; FM Class 3810 – 2005; ANSI/ISA
60079-0 – 2013; ANSI/ISA 60079-11 – 2012; ANSI/NEMA® 250
– 2003;
Markings XP CL I, DIV 1, GP B, C, D; DIP CLII/III, DIV 1, GP E, F, G; T4; -50 °C
≤ Ta ≤ 60 °C / 70 °C; Type 4X
Special Conditions for Safe Use (X):

1. WARNING – Potential Electrostatic Charging Hazard – The enclosure
contains non-metallic material. To prevent the risk for electrostatic
sparking the plastic surface should only be cleaned with a damp cloth.

2. WARNING – The apparatus enclosure contains aluminum and is

considered to constitute a potential risk of ignition by impact or
friction. Care must be taken into account during installation and use to
prevent impact or friction.
9.5.2 I5 Intrinsic Safety (IS), Nonincendive (NI)

60079-0 – 2013; ANSI/ISA 60079-11 – 2012; ANSI/NEMA 250 –
2003;
Markings IS CL I, II, III, DIV 1, GP A, B, C, D, E, F, G in accordance with
control drawing 9240030-936; IS (Entity) CL I, Zone 0, AEx ia IIC
T4 in accordance with control drawing 9240030-936, NI CL I, II,
III DIV 2, GP A, B, C, D, F, G; T4; -50 °C ≤ Ta ≤ 60 °C / 70 °C; Type
4X

1. WARNING –Potential Electrostatic Charging Hazard – The enclosure
Ui Ii Pi Ci Li
Entity parameters 30 V 130 mA 1W 7.26 nF 0

HART
Entity parameters 30 V 300 mA 1.3 W 0 0

Fieldbus
9.5.3 IE FISCO
60079-0 – 2013; ANSI/ISA 60079-11 – 2012; ANSI/NEMA 250 –
2003;
Markings IS CL I, II, III, DIV 1, GP A, B, C, D, E, F, G; T4; in accordance with
control drawing 9240030-936; IS CL I, Zone 0 AEx ia IIC T4 in

accordance with control drawing 9240030-936; -50 °C ≤ Ta ≤ 60

°C / 70 °C; Type 4X

1. WARNING – Potential Electrostatic Charging Hazard – The enclosure
Ui Ii Pi Ci Li
FISCO parameters 17.5 V 380 mA 5.32 W 0 0
9.6 Canada
9.6.1 E6 Explosionproof, Dust-Ignitionproof
Certificate 1514653
Standards CSA C22.2 No.0-M91, CSA C22.2 No.25-1966, CSA C22.2
No.30-M1986, CSA C22.2 No.94-M91, CSA C22.2 No.142-
M1987, CSA C22.2 157-92, CAN/CSA C22.2 No. 60529:05,
ANSI/ISA 12.27.01-2003
Markings Explosionproof CL I, DIV 1, GP B, C, D; Dust-Ignitionproof CL II,
DIV 1 and 2, GP E, F, G and coal dust, CL III, DIV 1, Type 4X/IP66/
IP67
9.6.2 I6 Intrinsically Safe and Non-Incendive Systems

Certificate 1514653
M1987, CSA C22.2 157-92, CAN/CSA C22.2 No. 60529:05,
ANSI/ISA 12.27.01-2003
Markings CL I, DIV 1, GP A, B, C, D, T4 see installation drawing
9240030-937; Non-Incendive Class III, DIV 1, Haz-loc CL I DIV 2,
GP A, B, C, D, Maximum Ambient Temperature +60 °C for
Fieldbus and FISCO and +70 °C for HART, T4, Type 4X/IP66/
IP67, Maximum Working Pressure 5000 psi, Dual Seal.

Ui Ii Pi Ci Li

HART
Entity parameters 30 V 300 mA 1.3 W 0 0

Fieldbus
9.6.3 IF FISCO
Certificate 1514653
M1987, CSA C22.2 157-92, CAN/CSA C22.2 No. 60529:05,
ANSI/ISA 12.27.01-2003
Markings CL I, DIV 1, GP A, B, C, D, T4 see installation drawing
9240030-937; Non-Incendive Class III, DIV 1, Haz-loc CL I DIV 2,
GP A, B, C, D, Maximum Ambient Temperature +60 °C, T4, Type
4X/IP66/IP67, Maximum Working Pressure 5000 psi, Dual Seal.
Ui Ii Pi Ci Li
FISCO parameters 17.5 V 380 mA 5.32 W 0 0
9.7 Europe
9.7.1 E1 ATEX Flameproof
Certificate Nemko 04ATEX1073X
Standards EN 60079-0:2012, EN 60079-1:2014, EN 60079-11:2012, EN
60079-26:2015, EN 60079-31:2014
Markings II 1/2G Ex db ia IIC T4 Ga/Gb, (-40 °C ≤ Ta ≤ +60 °C /+70 °C)
II 1D Ex ta IIIC T69 °C/T79 °C Da, (-40 °C ≤ Ta ≤ +60 °C /+70
°C)
Um = 250 V

1. Potential ignition hazards by impact or friction need to be considered
according to EN 60079-0:2012 clause 8.3 (for EPL Ga and EPG Gb), and
clause 8.4 (for EPL Da and EPL Db), when the transmitter enclosure and
antennas exposed to the exterior atmosphere of the tank, is made
with light metals containing aluminium or titanium. The end user shall
determine the suitability with regard to avoid hazards from impact and
friction.

2. Parts of the sensor probes, for type 5300 are non-conducting material
covering metal surfaces. The area of the non-conducting part exceeds
the maximum permissible areas for Group III according to EN
60079-0.2012 clause 7.4:3. Therefore, when the probe is used in a
potentially explosive atmosphere group III, EPL Da, appropriate
measures must be taken to prevent electrostatic discharge.
3. 1/2” NPT threads need to be sealed for dust and water ingress
protection, IP 66, IP 67 or “Ex t”, EPL Da or Db is required.
9.7.2 I1 ATEX Intrinsic Safety

60079-26:2015, EN 60079-31:2014
Markings II 1G Ex ia IIC T4 Ga, (-55 °C ≤ Ta ≤ +60 °C/+70 °C)
II 1D Ex ia IIIC T69 °C/T79 °C Da, (-50 °C ≤ Ta ≤ +60 °C /+70 °C)

1. The intrinsically safe circuits do not withstand the 500V AC test as
specified in EN 60079-11:2012 clause 6.3.13.
friction.
covering metal surfaces. The area of the non-conducting part exceeds
the maximum permissible areas for Group III according to EN
Ui Ii Pi Ci Li

HART
Entity parameters 30 V 300 mA 1.5 W 4.95 nF 0

Fieldbus

9.7.3 IA ATEX FISCO

60079-26:2015, EN 60079-31:2014
Markings II 1G Ex ia IIC T4 Ga (-55 °C ≤ Ta ≤+60 °C) or
II 1/2G Ex ia/ib IIC T4 Ga/Gb (-55 °C ≤ Ta ≤ +60 °C)
II 1D Ex ia IIIC T69 °C Da, (-50 °C ≤ Ta ≤ +60 °C)
II 1D Ex ia/ib IIIC T69°C Da/Db, (-50 °C ≤ Ta ≤ +60 °C)

1. The intrinsically safe circuits do not withstand the 500V AC test as
specified in EN 60079-11:2012 clause 6.3.13.
friction.
covering meatal surfaces. The area of the non-conducting part
exceeds the maximum permissible areas for Group III according to EN
4. The Ex ia version of model 5300 FISCO device may be supplied by an
“Ex ib” FISCO power supply, when the power supply is certified with
three separate safety current limiting devices and voltage limitation
which meets the requirements for type Ex ia.
Ui Ii Pi Ci Li
FISCO parameters 17.5 V 380 mA 5.32 W 4.95 nF <1 µH
9.7.4 N1 ATEX Type N



60079-31:2014
Markings II 3G Ex nA ic IIC T4 Gc (-50 °C ≤ Ta ≤ +60 °C /+70 °C)
II 3G Ex ic IIC T4 Gc (-50 °C ≤ Ta ≤ +60 °C /+70 °C)
II 3D Ex tc IIIC T69 °C/T79 °C Dc (-50 °C ≤ Ta ≤ +60 °C /+70 °C)

1. The transmitter circuits does not withstand 500V AC dielectric
strength test according to EN 60079-11 clause 6.3.13 due to earth
connected transient suppressing devices. Appropriate measures have
to be considered by installation.
Ui Ii Pi Ci Li
Safety parameters 42.4 V 23 mA 1W 7.25 nF Negligible

HART
Safety parameters 32 V 21 mA 0.7 W 4.95 nF Negligible

Fieldbus
9.8 International
9.8.1 E7 IECEx Flameproof
Certificate IECEx NEM 06.0001X
Standards IEC 60079-0:2011, IEC 60079-1:2014-06, IEC 60079-11:2011;
IEC 60079-26:2014, IEC 60079-31:2013
Markings Ex db ia IIC T4 Ga/Gb (-40 °C ≤ Ta ≤ +60 °C /+70 °C)
Ex ta IIIC T69 °C/T79 °C Da (-40 °C ≤ Ta ≤ +60 °C /+70 °C)
Um=250 VAC, IP66/IP67

according to IEC 60079-0:2011 clause 8.3 (for EPL Ga and EPL Gb) and
antenna exposed to the exterior atmosphere of the tank, is made with
light metals containing aluminum or titanium. The end user shall
friction.
2. Parts of the sensor probes for the type 5300 are non-conducting and
the area of the non-conducting part exceeds the maximum
permissible areas for Group III according to IEC 60079-0.2011 clause
7.4:3 Therefore, when the antenna is used in a potentially explosive

atmosphere group III, EPL Da, appropriate measures must be taken to

prevent electrostatic discharge.
3. ½” NPT threads need to be sealed for dust and water ingress
9.8.2 I7 IECEx Intrinsic Safety

IEC 60079-26:2014, IEC 60079-31:2013
Markings Ex ia IIC T4 Ga (-55 °C ≤ Ta ≤ +60 °C/+70 °C)
Ex ia IIIC T69 °C/T79 °C Da (-50 °C ≤ Ta ≤ +60 °C/+70 °C)

1. The Intrinsically safe circuits do not withstand the 500 V AC test as
specified in IEC 60079-11 clause 6.3.13
friction.
permissible areas for Group III according to IEC 60079-0.2011 clause
7.4:3 Therefore, when the antenna is used in a potentially explosive
atmosphere group III, EPL Da, appropriate measures must be taken to
prevent electrostatic discharge.
Ui Ii Pi Ci Li
Entity parameters 30 V 130 mA 1W 0 µF Negligible

HART
Entity parameters 30 V 300 mA 1.5 W 4.95 nF Negligible

Fieldbus
9.8.3 IG IECEx FISCO



IEC 60079-26:2014, IEC 60079-31:2013
Markings Ex ia IIC T4 Ga (-55 °C ≤ Ta ≤ +60 °C)
Ex ia/ib IIC T4 Ga/Gb (-55 °C ≤ Ta ≤ +60 °C)
Ex ia IIIC T69 °C Da (-50 °C ≤ Ta ≤ +60 °C)
Ex ia/ib IIIC T69 °C Da/Db (-50 °C ≤ Ta ≤ +60 °C)

1. The Intrinsically safe circuits do not withstand the 500 V AC test as
specified in IEC 60079-11 clause 6.3.13
friction.
permissible areas for Group IIC and according to IEC 6079-0.2011
clause 7.4: 20 cm2 for EPL Gb and 4 cm2 for EPL Ga. Therefore, when
the antenna is used in a potentially explosive atmosphere, appropriate
4. The Ex ia version of model 5300 FISCO field device may be supplied by
an [Ex ib] FISCO power supply when the power supply is certified with
three separate safety current limiting devices and voltage limitation
which meets the requirements for type Ex ia.
Ui Ii Pi Ci Li
FISCO parameters 17.5 V 380 mA 5.32 W 4.95 nF <1 µH
9.8.4 N7 IECEx Type N

Standards IEC 60079-0:2011, IEC 60079-11:2011, IEC 60079-15:2010, IEC
60079-31:2013
Markings Ex nA ic IIC T4 Gc (-50 °C ≤ Ta ≤ +60 °C /+70 °C)
Ex ic IIC T4 Gc (-50 °C ≤ Ta ≤ +60 °C /+70 °C)

Ex tc IIIC T69 °C/T79 °C Dc (-50 °C ≤ Ta ≤ +60 °C /+70 °C)

1. The transmitter circuits does not withstand 500V AC dielectric
strength test according to EN 60079-11 clause 6.3.13 due to earth
connected transient suppressing devices. Appropriate measures have
to be considered by installation.
Ui Ii Pi Ci Li

HART

Fieldbus
9.9 Brazil
9.9.1 E2 INMETRO Flameproof
Certificate UL-BR 17.0188X
Standards ABNT NBR IEC 60079-0:2013, ABNT NBR IEC 60079-1:2016,
ABNT NBR IEC 60079-11:2013, ABNT NBR IEC 60079-26:2016,
ABNT NBR IEC 60079-31:2014
Markings Ex db ia IIC T4 Ga/Gb (-40 °C ≤ Tamb ≤ +60 °C /+70 °C)
Ex ta IIIC T69 °C/T79 °C Da (-40 °C ≤ Tamb ≤ +60 °C /+70 °C)
Um=250 Vac, IP66/67

1. See certificate for Specific Conditions.
9.9.2 I2 INMETRO Intrinsic Safety

Certificate Certificate: UL-BR 17.0188X
Standards ABNT NBR IEC 60079-0:2013 , ABNT NBR IEC 60079-11:2013,
ABNT NBR IEC 60079-26:2016, ABNT NBR IEC 60079-31:2014
Markings Ex ia IIC T4 Ga (- 55 °C ≤ Tamb ≤ +60 °C /+70 °C)
Ex ia IIIC T69 °C/T79 °C Da (- 50 °C ≤ Tamb ≤ +60 °C /+70 °C)


Ui Ii Pi Ci Li
Entity parameters 30 Vdc 130 mA 1.0 W 7.26 nF Negligible

HART
Entity parameters 30 Vdc 300 mA 1.5 W 4.95 nF Negligible

Fieldbus
9.9.3 IB INMETRO FISCO

Certificate UL-BR 17.0188X
Standards ABNT NBR IEC 60079-0:2013, ABNT NBR IEC 60079-11:2013,
ABNT NBR IEC 60079-26:2016, ABNT NBR IEC 60079-31:2014
Markings Ex ia IIC T4 Ga (- 55 °C ≤ Tamb ≤ +60 °C)
Ex ia/ib IIC T4 Ga/Gb (- 55 °C ≤ Tamb ≤ +60 °C)
Ex ia IIIC T69 °C Da (- 50 °C ≤ Tamb ≤ +60 °C)
Ex ia/ib IIIC T69 °C Da/Db (- 50 °C ≤ Tamb ≤ +60 °C)

Ui Ii Pi Ci Li
FISCO parameters 17.5 Vdc 380 mA 5.32 W 4.95 nF <1 µH
9.10 China
9.10.1 E3 China Flameproof
Certificate GYJ16.1095X
Standards GB 3836.1/2/4/20-2010, GB 12476.1/5-2013, GB
12476.4-2010
Markings Ex d ia IIC T4 Ga/Gb (-40 °C ≤ Ta ≤ +60 °C/+70 °C)
Ex tD A20 IP 66/67 T69 °C /T79 °C (-40 °C ≤ Ta ≤ +60 °C/+70 °C)

9.10.2 I3 China Intrinsic Safety

12476.4-2010

Markings Ex ia IIC T4 Ga (-50 °C ≤ Ta ≤ +60 °C/+70 °C)

Ex iaD 20 T69 °C /T79 °C (-50 °C ≤ Ta ≤ +60 °C/+70 °C)
Ex iaD/ibD 20/21 T69 °C (-50 °C ≤ Ta ≤ +60 °C)

Ui Ii Pi Ci Li
Entity parameters 30 V 130 mA 1W 7.26 nF 0 mH

HART
Entity parameters 30 V 300 mA 1.5 W 4.95 nF 0 mH

Fieldbus
9.10.3 IC China FISCO

12476.1-2010
Markings Ex ia IIC T4 Ga (-50 °C ≤ Ta ≤ +60 °C)
Ex ia/ib IIC T4 Ga/Gb (-50 °C ≤ Ta ≤ +60 °C)
Ex iaD 20 T69 (-50 °C ≤ Ta ≤ +60 °C)
Ex iaD/ibD 20/21 T69 °C (-50 °C ≤ Ta ≤ +60 °C)

Ui Ii Pi Ci Li
FISCO parameters 17.5 V 380 mA 5.32 W 4.95 nF <0.001 mH
9.10.4 N3 China Type N

Standards GB 3836.1-2010, GB 3836.4-2010, GB 3836.8-2014
Markings Ex nA ic IIC T4 Gc (-50 °C ≤ Ta ≤ +60 °C/+70 °C)
Ex ic IIC T4 Gc (-50 °C ≤ Ta ≤ +60 °C/+70 °C)


Ui Ii Pi Ci Li

HART

Fieldbus
9.11 Technical Regulations Customs Union (EAC)
9.11.1 EM Technical Regulations Customs Union (EAC) Flameproof

Certificate RU C-SE.AA87.B.00802
Markings Ga/Gb Ex db ia IIC T4….T1 X, (-40 °C ≤ Ta ≤ +60 °C/+70 °C)
Ex ta IIIC T69 °C/T79 °C Da X (-40 °C ≤ Ta ≤ +60 °C/+70 °C)

9.11.2 IM Technical Regulations Customs Union (EAC) Intrinsic Safety

Certificate RU C-SE.AA87.B.00802
Markings 0Ex ia IIC T4...T1 Ga X, (-55 °C ≤ Ta ≤ +60 °C/+70 °C)
Ga/Gb Ex ia/ib IIC T4…T1 X, (-55 °C ≤ Ta ≤ +60 °C/+70 °C)
Ex ia IIIC T69 °C/T79 °C Da X, (-50 °C ≤ Ta ≤ +60 °C/+70 °C)
Da/Db Ex ia/ib IIIC T69 °C/T79 °C X, (-50 °C ≤ Ta ≤ +60 °C/+70 °C)

Ui Ii Pi Ci Li
Entity parameters 30 V 130 mA 1W 7.26 nF 0 mH

HART
Entity parameters 30 V 300 mA 1.5 W 4.95 nF 0 mH

Fieldbus
9.12 Japan
9.12.1 E4 Flameproof
Certificate CML 17JPN1334X
Markings Ex d ia IIC T4 Ga/Gb (-40 °C ≤ Ta ≤ +60 °C/+70 °C)


9.13 Republic of Korea

9.13.1 EP Flameproof HART
Certificate KTL 15-KB4BO-0297X
Markings Ex d ia IIC T4 Ga/Gb

9.13.2 EP Flameproof Fieldbus

Certificate KTL 12-KB4BO-0179X
Markings Ex ia/d ia IIC T4

9.14 India
9.14.1 Flameproof, Intrinsically safe
Certificate P392482/1
Markings Ex db ia IIC T4 Ga /Gb
Ex ia IIC T4 Ga

9.15 Ukraine
9.15.1 Flameproof, Intrinsically Safe
Certificate UA.TR.047.C.0352-13
Markings 0 Ex ia IIC T4 X,
1 Ex d ia IIC T4 X


9.16 Uzbekistan
9.16.1 Safety (import)
Certificate UZ.SMT.01.342.2017121
9.17 Combinations
KA Combination of E1, E5 and E6
KB Combination of E1, E5 and E7
KC Combination of E1, E6 and E7
KD Combination of E5, E6 and E7
KE Combination of I1, I5 and I6
KF Combination of I1, I5 and I7
KG Combination of I1, I6 and I7
KH Combination of I5, I6 and I7
KI Combination of IA, IE and IF
KJ Combination of IA, IE and IG
KK Combination of IA, IF and IG
KL Combination of IE, IF and IG
9.18 Additional certifications

9.18.1 SBS American Bureau of Shipping (ABS) Type Approval
Certificate 15-LD1340199-1-PDA
Intended Use For use on ABS Classed Vessels and Offshore Facilities in
accordance with ABS rules and International Standards.
Note
Housing material A, Aluminum, is not to be used on open decks.
9.18.2 SBV Bureau Veritas (BV) Type Approval

Certificate 22378_B3 BV
Requirements Bureau Veritas rules for classification of steel ships. EC
Code: 41SB
Application Class Notations: AUT-UMS, AUT-CCS, AUT-PORT and AUT-
IMS.

Note
9.18.3 SDN Det Norske Veritas Germanischer Lloyd (DNV GL) Type Approval
Certificate TAA000020G
Intended Use DNV GL rules for classification – Ships, offshore units, and
high speed and light craft
Table 9-1: Application
Location classes
Temperature D
Humidity B
Vibration A
EMC B
Enclosure C
Note
9.18.4 SLL Lloyds Register (LR) Type Approval

Certificate 15/20053
Application Marine applications for use in environmental categories ENV1,
ENV2, ENV3 and ENV5.
Note
9.18.5 U1 Overfill prevention

Certificate Z-65.16-476
Application TÜV tested and approved by DIBt for overfill prevention
according to the German WHG regulations.
9.18.6 J8 EN Boiler (European Boiler Approval in accordance with EN

12952-11 and EN 12953-9)
Note
Suitable for use as a level sensor part of a limiting device in accordance with
EN 12952-11 and EN 12953-9.

9.18.7 QT Safety-certified to IEC 61508 with certificate of FMEDA data

Certificate exida ROS 13-06-005 C001 R1.3
9.18.8 Suitable for intended use

Compliant with NAMUR NE 95, version 22.01.2013 “Basic Principles of
Homologation”
9.19 Pattern Approval

GOST Belarus
Certificate RB-03 07 2765 10
GOST Kazakhstan
Certificate KZ.02.02.03473-2013
GOST Russia
Certificate SE.C.29.010.A
GOST Uzbekistan
Certificate 02.2977-14
China Pattern Approval
Certificate CPA 2012-L135
9.20 Conduit plugs and adapters

IECEx Flameproof and Increased Safety
Certificate IECEx FMG 13.0032X

Standards IEC60079-0:2011, IEC60079-1:2007, IEC60079-7:2006-2007
Markings Ex de IIC Gb
ATEX Flameproof and Increased Safety
Certificate FM13ATEX0076X
Standards EN60079-0:2012, EN60079-1:2007, IEC60079-7:2007
Markings II 2 G Ex de IIC Gb

Table 9-2: Conduit Plug Thread Sizes
Thread Identification mark
M20 x 1.5 M20
½ - 14 NPT ½ NPT
Table 9-3: Thread Adapter Thread Sizes
Male thread Identification mark
M20 x 1.5 – 6g M20
½- 14 NPT ½ - 14 NPT
¾ - 14 NPT ¾- 14 NPT
Female thread Identification mark
M20 x 1.5 – 6H M20
½ - 14 NPT ½ - 14 NPT
G1/2 G1/2

1. When the thread adapter or blanking plug is used with an enclosure in
type of protection increased safety “e” the entry thread shall be
suitably sealed in order to maintain the ingress protection rating (IP) of
the enclosure.See certificate for Specific Conditions.
2. The blanking plug shall not be used with an adapter.
3. Blanking Plug and Threaded Adapter shall be either NPT or Metric
thread forms. G½ thread forms are only acceptable for existing
(legacy) equipment installations.

9.21 Installation drawings

Figure 9-1: 9240030-936 - System Control Drawing for Hazardous Location
Installation of Intrinsically Safe FM Approved Apparatus

Figure 9-2: 9240030-937 - Installation Drawing for Hazardous Location

Installation of Intrinsically Safe CSA Approved Apparatus

Figure 9-3: D9240030-938 - Installation Drawing for Hazardous Location

Installation of Intrinsically Safe ATEX and IECEx Approved Apparatus

Figure 9-4: 9240031-957 - Installation Drawing Exn

9.22 EU Declaration of Conformity

Figure 9-5: EU Declaration of Conformity




9.23 China RoHS

List of Model Parts with China RoHS Concentration above MCVs
含有China RoHS管控物峐超彯㚨⣏㳻⹎旸ῤ的部件型号列表
Hazardous Substances / 有害物峐
Part Name Hexavalent Polybrominated Polybrominated

部件名称
Lead Mercury Cadmium
汞
Chromium biphenyls diphenyl ethers
摭擱
භ௴撔 ከ⁏俼劗 ከ⁏俼劗慂(PBDE)
(Pb) (Hg) (Cd)
(Cr +6) (PBB)
Electronics
Assembly X O O O O O
䓝⫸乬ẞ
Housing
Assembly O O O O O O
体乬ẞ
This table is proposed in accordance with the provision of SJ/T11364
本表格系依据SJ/T11364的奬⭂侴⇞ἄį
O: Indicate that said hazardous substance in all of the homogeneous materials for this part is below the limit requirement
of GB/T 26572.
O: 意ᷢ宍悐ẞ䘬㇨㚱⛯峐㛸㕁ᷕ宍㚱⭛䈑峐䘬⏓慷⛯ỶḶGB/T 26572所奬⭂䘬旸慷天㯪į
X: Indicate that said hazardous substance contained in at least one of the homogeneous materials used for this part is
above the limit requirement of GB/T 26572.
X: 意ᷢ⛐宍悐ẞ㇨ἧ䓐䘬㇨㚱⛯峐㛸㕁慴炻军⮹㚱ᶨ䰣⛯峐㛸㕁ᷕ宍㚱⭛䈑峐䘬⏓慷檀ḶGB/T 26572所奬⭂䘬旸慷天㯪į

*00825-0100-4530*
Quick Start Guide
00825-0100-4530, Rev. HA
February 2019
Global Headquarters North America Regional Office

Emerson Automation Solutions Emerson Automation Solutions
6021 Innovation Blvd. 8200 Market Blvd.
Shakopee, MN 55379, USA Chanhassen, MN 55317, USA
+1 800 999 9307 or +1 952 906 8888 +1 800 999 9307 or +1 952 906 8888
+1 952 949 7001 +1 952 949 7001
[email protected] [email protected]
Latin America Regional Office Europe Regional Office

Emerson Automation Solutions Emerson Automation Solutions Europe
1300 Concord Terrace, Suite 400 GmbH
Sunrise, FL 33323, USA Neuhofstrasse 19a P.O. Box 1046
+1 954 846 5030 CH 6340 Baar
Switzerland
+1 954 846 5121
+41 (0) 41 768 6111
[email protected]
+41 (0) 41 768 6300
[email protected]
Asia Pacific Regional Office Middle East and Africa Regional Office
Emerson Automation Solutions Emerson Automation Solutions
1 Pandan Crescent Emerson FZE P.O. Box 17033
Singapore 128461 Jebel Ali Free Zone - South 2
+65 6777 8211 Dubai, United Arab Emirates
+65 6777 0947 +971 4 8118100
[email protected] +971 4 8865465
[email protected]
Linkedin.com/company/Emerson-
Automation-Solutions ©2019 Emerson. All rights reserved.
Twitter.com/Rosemount_News Emerson Terms and Conditions of Sale are

Facebook.com/Rosemount available upon request. The Emerson logo is a
trademark and service mark of Emerson Electric
Youtube.com/user/
Co. Rosemount is mark of one of the Emerson
RosemountMeasurement
family of companies. All other marks are the
Google.com/+RosemountMeasurement property of their respective owners.

Lit Quick Start Guide

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Lit Quick Start Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lit Quick Start Guide

Uploaded by

Copyright:

Available Formats

Quick Start Guide

Rosemount™ 5300 Level Transmitter

Guided Wave Radar

2 Rosemount 5300 Level Transmitter

1 About this guide

Quick Start Guide 3

4 Rosemount 5300 Level Transmitter

2 Confirm system readiness (HART® only)

2.2 Confirm correct device driver

Firmware version (1) Find Device Driver

HART® Universal Device Revision (2)

2.3 Switch HART® revision mode

Quick Start Guide 5

3 Mount transmitter on tank

3.1 Threaded/Flange/Tri-Clamp® tank connection

2. Mount the device on tank.

6 Rosemount 5300 Level Transmitter

3. (Optional) Adjust display orientation.

4. Tighten the nut.

Torque 30 ft-lb (40 Nm)

Quick Start Guide 7

3.2 Install remote housing

2. Mount the probe on tank.

3. Mount the remote connection on the probe.

Torque 30 ft-lb (40 Nm)

8 Rosemount 5300 Level Transmitter

4. Mount the bracket to the pipe.

5. Fasten the housing support.

6. Mount the transmitter head.

Torque 30 ft-lb (40 Nm)

Quick Start Guide 9

3.3 Bracket mounting

2. Mount the transmitter with probe to the bracket.

10 Rosemount 5300 Level Transmitter

4 Prepare the electrical connections

4.1 Cable gland/conduit

4.2 Power supply (Vdc)

None 16-42.4 9-32 8-30 (max. rating)

Non-sparking/ 16-42.4 9-32 N/A

Intrinsically safe 16-30 9-30 N/A

FISCO N/A 9-17.5 N/A

Explosion-proof/ 20-42.4 16-32 8-30 (max. rating)

Quick Start Guide 11

4.3 4-20 mA/HART® communication

Figure 4-1: Wiring Diagram for 4-20 mA/HART®

4.3.2 Load limitations

12 Rosemount 5300 Level Transmitter

Figure 4-2: Intrinsically Safe Installations

A. Loop Resistance (Ohms)

Figure 4-3: Non-Hazardous and Non-Sparking/Energy Limited

A. Loop Resistance (Ohms)

Quick Start Guide 13

Figure 4-4: Explosion-Proof /Flameproof (Ex d) Installations

A. Loop Resistance (Ohms)

14 Rosemount 5300 Level Transmitter

4.4 FOUNDATION™ Fieldbus

Figure 4-5: Wiring Diagram for FOUNDATION Fieldbus

4.5 RS-485 with Modbus® communication