Papastefanou (2009) - Radon Decay Product Aerosols in Ambient Air
Papastefanou (2009) - Radon Decay Product Aerosols in Ambient Air
Papastefanou (2009) - Radon Decay Product Aerosols in Ambient Air
Constantin Papastefanou*
Atomic and Nuclear Physics Laboratory, Aristotle University of Thessaloniki, Thessaloniki 54124, Greece
ABSTRACT
The aerodynamic size distributions of radon decay product aerosols, i.e. 214Pb, 212Pb, and 210Pb were measured using low-pressure
(LPI) as well as conventional low-volume 1-ACFM and high-volume (HVI) cascade impactors. The activity size distribution of 214Pb
and 212Pb was largely associated with submicron aerosols in the accumulation mode (0.08 to 2.0 ȝm). The activity median aerodynamic
diameter “AMAD” varied from 0.10 to 0.37 ȝm (average 0.16 ȝm) for 214Pb-aerosols and from 0.07 to 0.25 ȝm (average 0.12 ȝm) for
212
Pb-aerosols. The geometric standard deviation, ıg averaged 2.86 and 2.97, respectively. The AMAD of 210Pb-aerosols varied from
0.28 to 0.49 ȝm (average 0.37 ȝm) and the geometric standard deviation, ıg varied from 1.6 to 2.1 (average 1.9). The activity size
distribution of 214Pb-aerosols showed a small shift to larger particle sizes relative to 212Pb-aerosols. The larger median size of 214Pb-
aerosols was attributed to Į-recoil depletion of smaller aerosol particles following the decay of the aerosol-associated 218Po. Subsequent
214
Pb condensation on all aerosol particles effectively enriches larger-sized aerosols. Pb-212 does not undergo this recoil-driven
redistribution. Even considering recoil following 214Po Į-decay, the average 210Pb-labeled aerosol grows by a factor of two during its
atmospheric lifetime. Early morning and afternoon measurements indicated that similar size associations of 214Pb occur, despite
humidity differences and the potential for fresh particle production in the afternoon. In estimating lifetimes of radon decay product
aerosols in ambient air, a mean residence time of about 8 days could be applied to aerosol particles in the lower atmosphere below
precipitation cloud levels.
Keywords: Radon; Decay products; 214Pb; 212Pb; 210Pb; Radioactive aerosols; Cascade impactors; 1-ACFM; AMAD; Residence time.
INTRODUCTION
derived values of the residence times due to various processes, Division building at the Oak Ridge National Laboratory, ORNL,
including the fact that they refer to different portions of the in Oak Ridge, Tennessee (35o58’N, 84o30’W).
atmosphere. The deposits on the stainless-steel collection plates of the low-
This paper summarizes results of an investigation designed to pressure cascade impactor were leached with a solution of 1 M
characterize the aerodynamic size distributions and the residence HNO3 and the leachate rapidly evaporated on 5.08-cm stainless
time of atmospheric aerosols in the context of 222Rn- and 220Rn- steel plates using a hot plate. The concentrations of 214Pb and
212
decay products for better understanding of how radioactive Pb in the impactor plate leachates were measured using seven
aerosols behave in the atmosphere, and of the aerosol growth ZnS (Ag) alpha scintillation counters with backgrounds averaged
mechanism. 0.025 cpm. The 1 ı counting uncertainty was 5% or less for the
stages corresponding to aerosols below 0.52 ȝm and < 15% for
EXPERIMENTAL METHODS the stages collecting to aerosols above 0.52 ȝm. The calculated
activities of 214Pb and 212Pb were used to determine the activity
Measurements on aerodynamic sizes of atmospheric aerosols size distribution of each radionuclide and then the activity
associated with radioactive nuclides, such as radon decay median aerodynamic diameter “AMAD” of the 214Pb- and 212Pb-
products 214Pb, 212Pb and 210Pb were carried with Anderson type aerosols. The high-volume impactor plates were leached with 0.1
1-ACFM ambient cascade impactors with or without the M HCl. Lead-210 was determined 30 days after collection
Andersen model 2000 low-pressure modification, as well as with stopped by separating and measuring 210Bi (Poet et al., 1972).
Sierra model 236, six-stage high-volume cascade impactors, HVI. When 210Pb was measured, the upper two high-volume impactor
The 1-ACFM design operated at 28 L/min (1 ft3/min). The stages were coated with a thin layer of petroleum jelly to
eight stages had effective cutoff diameters, ECDs of 0.4, 0.7, 1.1, minimize soil particle bounce. While nuclepore polycarbonate
2.1 3.3, 4.7, 7.0 and 11.0 ȝm. The low-pressure modification, membranes (0.4 ȝm) were preferred as backup filters for low-
which alters the impactor’s operation by increasing the resolution pressure cascade impactors, glass-fiber filters had to be used in
in the submicron region, involves a regulated flow rate of 3 the high-volume impactor measurements.
L/min, five low-pressure (114 mm Hg) stages for the submicron The activity of 210Pb- and 210Bi-associated aerosol particles
region and eight atmospheric pressure stages for separating was measured by a low-background phoswitch scintillation
aerosol particles above 1.4 ȝm. The ECDs of the low-pressure detector system having a background of 2 cpm and efficiency
stages were 0.08, 0.11, 0.23, 0.52 and 0.90 ȝm, whereas for the higher than 40% for counting ȕ-radiation. This system consisted
upper stages they were 1.4, 2.0, 3.3, 6.6, 10.5, 15.7, 21.7 and 35.0 of a thin CaF2 (Eu) primary crystal with a decay time of 0.23 ȝs.
ȝm. A schematic diagram of a low-pressure cascade impactor, The samples were counted for long enough to obtain a statistical
LPI complete system is shown in Fig. 2. The stainless steel plates accuracy better than 5%. It must be noted that 210Pb and 210Bi
supplied by the manufacturer were used for aerosol particle were chemically separated and measured for their activities.
collection. Either polycarbonate or glass-fiber backup filters were Detailed description of the analytical method and technique was
used to collect all particles below the 0.08-ȝm collection plate. established and presented elsewhere (Jaworowski, 1963). The
The ECDs of the high-volume impactor stages were 0.41, 0.73, activity of 210Pb was also measured by a surface barrier Ge
1.4, 2.1, 4.2 and 10.2 ȝm. The flow rate of this 20 cfm high- detector through its gamma-ray peak of 46.5 keV. The activity
volume cascade impactor was about 34 m3/h. size distribution and the AMAD of the 210Pb-aerosol particles
The length of each collection period varied from about 3 h for were determined upon the measurement of the activities of the
214
Pb to 30 or 40 h for 212Pb with low-pressure impactor aerosol-associated radioactive nuclides. Fig. 3 shows a typical
measurements and from 1 to 24 h for 210Pb and 210Bi for high- gamma-ray spectrum of a glass fiber air filter obtained by a Ge
volume impactor measurements. The samples were collected 13 detector, in which the 46.5 keV Ȗ-ray peak of 210Pb is clearly
m above the ground on the roof of the Environmental Sciences shown.
Fig. 3. Plot of a Ȗ-ray spectrum of an atmospheric aerosol sample (air filter) obtained by a Ge detector.
RESULTS AND DISCUSSION The longer half-life of 212Pb (10.64 h) compared to 214Pb (26.8
min) might favor the presence of larger aerosol associations of
212
Activity Size Distribution of Radon Decay Product Aerosols Pb if coagulation rates are fast relative to radioactive decay
Fig. 4 shows representative plots from 46 low-pressure rates, although cascade impactor measurements may not be
impactor measurements made over a ten-month period, sensitive enough to record this effect. Instead, the measurements
illustrating the aerodynamic size distributions of 214Pb- and 212Pb- indicated that the shorter-lived chain (218Po, 214Pb, etc) was more
aerosols. R is the radioactivity and Dp is the particle diameter, in often associated with larger aerosol particle sizes than the longer-
ȝm. lived chain (216Po, 212Pb, etc). The high-volume impactor
About 46% of the measurements showed a radioactivity peak measurements reported by Röbig et al. (1980) also indicated a
in the 0.11- to 0.23-ȝm region (subplot a), while 39% showed a large particle shift of 214Pb relative to 212Pb (Fig. 6). They stated
peak in the 0.23- to 0.52-ȝm region (subplot b). The remaining that this was due to shifts of the activity size distributions from
15% of the measurements resulted in activity size distributions night to day-time to smaller particle sizes by photochemical
similar to those in subplot c (8.7%) or subplot d (6.5%), where reactions and to shifts to larger particle sizes when the relative
214
Pb- and 212Pb- activities were highest in different size ranges in humidity increases during rainfall, and therefore depends on
the same spectrum. On the average, about 76% of the 214Pb- sampling time. They also observed that the activity size
activity and 67% of the 212Pb-activity was found to be associated distributions of the long-lived radionuclides 210Pb and 7Be are
with aerosol particles in the 0.08- to 1.4-ȝm size range. The shifted to larger particle sizes compared with the activity size
activity- associated with aerosol particles smaller than 0.08-ȝm distributions of the shorter-lived 214Pb and 212Pb. That shift was
can also be substantial, as indicated in Fig. 4. Fig. 4 illustrates due to larger residence times for 210Pb and 7Be in the atmosphere
that 214Pb is generally enriched in the accumulation mode aerosol, and for 7Be due to a different size distribution of stratospheric
particularly between 0.11 and 0.52 ȝm, where most of the surface and tropospheric aerosols.
area and mass occurs, while the Aitken nuclei fraction (below The 214Pb shift might be explained by the fact that a significant
0.08 ȝm) contained a higher percentage of 212Pb-activity fraction of the 3.05-min 218Po atoms, precursor of 214Pb atoms
compared with 214Pb-activity in 69.6% of the measurements. should attach to an existing aerosol particle or coagulate with
The radon decay products become associated with atmospheric other nuclei during their lifetime, as mean attachment half-lives
aerosol particles by condensation or coagulation processes that are of the order of a minute less (Porstendörfer and Mercer, 1980).
are surface-area related. The activity size distribution of 214Pb- When this attached 218Po Į-decays, the recoiling 214Pb atom,
aerosols showed a small shift to larger particle sizes relative to decay product of 218Po, can escape the aerosol particles.
212
Pb-aerosols. The shift of 214Pb to a slightly higher size Complete recoil loss would occur if the particle diameter, Dp of
distribution compared to 212Pb was also found using 1-ACFM the aerosol were smaller than the range of the recoiling nucleus.
and high-volume cascade impactors (Fig. 5). The higher flow In water, this recoil range is 0.13 ȝm (Mercer, 1976) and should
rates of these impactors, as well as the ability to measure high- be somewhat less in the atmospheric aerosols that have a density
volume activity by gamma-ray spectrometry, made us confident closer to 1.5 g cm-3 (Friedlander, 2000). By contrast, very little of
that this shift was real and not a data analysis artifact. The larger the 0.146 ȝs-216Po would attach before decaying to 212Pb, because
median size of 214Pb-aerosols was attributed to Į-recoil depletion of its short life relative to attachment times. A considerable
of smaller aerosol particles following the decay of the aerosol- fraction of the 214Pb should undergo recoil detachment,
associated 218Po. Subsequent 214Pb condensation on all particles particularly from aerosol particles with diameters smaller than
effectively enriches larger-sized aerosols. Pb-212 does not 0.1 ȝm (diameter approximating the recoil range). The
undergo this recoil-driven redistribution. Even considering recoil probability of loss would decrease with increasing particle radius
following 214Po Į-decay, the average 210Pb-labelled aerosol grows (Mercer, 1976). If the recondensing 214Pb behaves like the
by a factor of two during its atmospheric lifetime. Early morning original 214Po, the net effect would be a shift of 214Pb to a larger
and afternoon measurements indicated that similar size particle size distribution.
associations of 214Pb occur, despite humidity differences and the Since the subsequent ȕ-decays of 212Pb and 214Pb + 214Bi do not
potential for fresh particle production in the afternoon. result in significant recoil (Mercer, 1976), the Į-measurement of
388 Papastefanou, Aerosol and Air Quality Research, 9: 385-393, 2009
Fig. 4. Aerodynamic size distributions of 214Pb- and 212Pb-aerosols obtained with low-pressure cascade impactors. R is the radioactivity,
and Dp is the particle diameter. (a) Results occurred 46% of the time, (b) 39% of the time, (c) 8.7% of the time, and (d) 6.5% of the time.
Lower Dp limits are arbitrary.
Fig. 5. Aerodynamic size distributions of 214Pb- and 212Pb-aerosols obtained with 1-ACFM and high-volume cascade impactors,
illustrating the large particle shift of 214Pb. R is the radioactivity, and Dp is the particle diameter. Lower Dp limits are arbitrary.
214
Po and the 212Pb-decay products is in reality tracing the aerosol ȝm) and for 212Pb-aerosols from 0.07 to 0.25 ȝm (average 0.12
size distribution of a 220Rn-decay product atom (212Pb) which has ȝm) (Table 1). For the 210Pb-aerosols the AMADs varied from
condensed only once and a 222Rn-decay product atom (214Pb) that 0.28 to 0.49 ȝm (average 0.37 ȝm). Lead-210 is produced by Į-
has probably condensed more than once. This stability of the Pb- decay of 214Po, the event used to quantify 214Pb distributions on
isotopes is the basis for the generic reference to 212Pb and 214Pb the low-pressure cascade impactors. While the relationship
size distributions. between the aerodynamic sizes of 214Pb and 210Pb is complicated
The AMADs of 214Pb-aerosols determined with the low- because of the large differences in their atmospheric lifetimes,
210
pressure impactor data varied from 0.10 to 0.37 ȝm (average 0.16 Pb has always found to be associated with aerosols larger than
Papastefanou, Aerosol and Air Quality Research, 9: 385-393, 2009 389
Table 1. Activity median aerodynamic diameters (AMADs) of radon decay product aerosols.
214 212 210
Pb AMADs (ȝm) Pb AMADs (ȝm) Pb AMADs (ȝm) Reference
0.10-0.37 (avg. 0.16) 0.07-0.25 (avg.0.12) 0.28-0.49 (avg. 0.37) This work
- 0.42 0.56 Grundel and Porstendörfer (2004)
- - 0.28-0.74 (avg. 0.53) Winkler et al. (1998)
0.26-0.46 (avg. 0.38) - - El Hussein and Ahmed (1995)
0.18-0.49 (avg. 0.33) - - El Hussein et al. (1998)
0.30-0.36 (avg. 0.32) 0.25-0.39 (avg. 0.36) - Mohammed (1999)
- - 0.70 Suzuki et al. (1999)
390 Papastefanou, Aerosol and Air Quality Research, 9: 385-393, 2009
distribution of 7Be in atmospheric aerosols and then the AMAD and the Eq. (2) by the formula
was achieved by using Andersen 1-ACFM cascade impactors, in
association with a gamma-ray spectrometer linked with a Ge 1
coaxial-type detector for the 7Be activity measurement of the WR 1 O Pb 1 O Pb (O Pb N Pb O Rn N Rn )
(O Rn N Rn O Pb N Pb ) 1
collection plates and the back up filter of the impactor.
(6)
Residence Times of Radon Decay Product Aerosols
The method for estimating the residence time of atmospheric where ȜPb = 8.5 × 10-5/d is the decay constant of 210Pb and ȜRn
aerosol particles associated with the radon decay product NRn / ȜPb NPb >> 1.
radionuclides is based on the radioactivity of a pair of genetically The ratio of the activities ȜRn NRn / ȜPb NPb in Eq. 6 varied from
related radioisotopes, such as 210Pb, 210Bi and or 210Pb, 210Po, 282 to 7700 (Moore et al., 1972).
according to the sequential disintegrations in the ȕ-decay scheme Taking into account the 210Bi/210Pb ratios as determined in
twenty one measurements of aerosol samplings carried out during
210
Pb (ȕ-, 22.3 y) o 210
Bi (ȕ-, 5.01 d) o 210
Po (Į, 138.38 d) an annual period at Oak Ridge, Tennessee at temperate latitude
o 206
Pb (stable) (35o58’N, 84o17’W) with high precipitation (wet climate), the
estimated residence time of atmospheric aerosols in the boundary
The residence time, IJR is described by the formula layer varied from 4.8 to 15.3 days (average 8.2 days).
Table 2 shows data for the residence times, IJR of atmospheric
aerosol particles associated with radon, 222Rn and radon decay
O Bi N Bi O Pb N Pb products 210Pb, 210Bi and 210Po. The reported from the literature
WR 1 O Bi (1)
1 (O Bi N Bi O Pb N Pb ) IJR values are also shown in Table 2 and analyzed as follows:
Poet et al. (1972) estimated tropospheric aerosol residence
where ȜBi NBi is the activity of 210Bi, ȜPb NPb is the activity of times ranging from 1.59 to 13 days (average 5.4 days) when
210
Pb in air and ȜBi = 0.138 d-1 is the decay constant of 210Bi. based on the 210Bi/210Pb activity ratios and from 11 to 77 days
The Eq. (1) was derived from the equation of the production (average 24 days) when based on the 210Po/210Pb activity ratios
and removal of radionuclides assuming asteady state equilibrium for twenty measurements of aerosol samplings carried out in
surface air during a 4 ½-year period at Boulder, Colorado
(40o01’N, 105o17’W). They concluded that, a mean tropospheric
dN Bi dt O Pb N Pb (O Bi O R ) N Bi 0 (2)
residence time of about 4 days could be applied for aerosol
particles in the lower troposphere and about a week for aerosol
where ȜR = 1/IJR is the first-order rate constant for the removal of particles in precipitation. They also found that the mean aerosol
aerosol particles from the atmosphere by all processes, that is the residence time increases with altitude within troposphere less
inverse of residence time, IJR. than by a factor of 3 (Moore et al., 1973).
The ratio of the activities ȜBi NBi / ȜPb NPb in Eq. (1) varied Francis et al. (1970) estimated a mean atmospheric residence
from 0.40 to 0.68 (this work) or from 0.42 to 0.85 (Moore et al., time for 210Pb of 9.6 days ± 20% based on the 210Po/210Pb activity
1972). ratios from the dust of filtrate (> 0.22 ȝm) collected during a 3-
If the activity of 210Po, ȜPo NPo in air is considered and ȜPo = month period (May-August) at Madison, Wiskonsin (43o05’N,
5.0 × 10-3/d is the decay constant of 210Po, then the activity ratio 89o22’W).
of 210Po, ȜPo NPo and 210Pb, ȜPb NPb is given by the equation Marley et al. (2000) estimated residence times for seven
aerosol samples collected at Argonne, Illinois (41.7oN, 88.0oW)
WR
2 during a 2-year period, three aerosol samples collected at Phoenix,
O Po N Po O Pb N Pb (3) Arizona, one sample collected at Socorro, New Mexico, and five
(W R 1 O Bi ) (W R 1 O Po ) samples collected at Mexico city, Mexico. Based on the
210
Bi/210Pb activity ratios, they resulted in residence times of 6 to
from which the residence time, IJR is determined as 67 days, while based on the 210Po/210Pb activity ratios, they
suggested residence times of 33 to 66 days for the aerosols below
- b (b 2 4ac)1 2 2 ȝm in size.
WR (4) Much earlier, Fry and Menon (1962) in twelve measurements
2a carried out during a 7-month period (spring and summer) at
Fayetteville, Arkansas (36o03’N, 78o54”W), indicated apparent
where aerosol residence times ranging from 2.4 to 25.6 days (average
a O Pb N Pb O Po N Po 8.5 days), based on the 210Bi/210Pb activity ratios in Arkansas
b c O Pb N Pb (1 O Bi 1 O Po ) rains. Gavini et al. (1974) also estimated residence times varied
(5) from 3 to 240 days (average 29 days) from the 210Bi/210Pb activity
c -O Po N Po (1 O Bi O Po ) ratios in Arkansas rains also.
O Bi 0.138 d and O Po 5 u 10 - 3 d Baskaran and Shaw (2001) based on the 210Po/210Pb activity
ratios estimated residence times of arctic haze aerosols, from the
upper atmosphere to the arctic atmosphere, varied between 12
The ratio of the activities ȜPo NPo / ȜPb NPb in Eq. (3) varied and 32 days from the measurements carried out during an 1 1/2 –
from 0.054 to 0.092 (Moore et al., 1972). year period (winter) at Poker Flat (65.1oN, 147.5oW) and between
The residence time, IJR can also be determined through the ratio 0 and 39 days from eight measurements carried out during a 2-
of the activities of radon, 222Rn, ȜRn NRn and 210Pb, ȜPb NPb in air month period (winter) at Eagle (69.5oN, 141.2oW) in Alaska.
according to the sequential disintegrations in the Į- and ȕ-decay Very early, Lehman and Sittkus (1959) estimated aerosol
scheme as residence times of 20 days from the 210Po/210Pb activity ratios in
air at Freiburg, Germany (47o59’N, 7o51’E), while Peirson et al.
Rn (Į, 3.824 d) o 218Po (Į, 3.05 min) o 214Pb (ȕ-, 26.8
222
(1966) estimated aerosol residence times of 40 days from the
min) o 214Bi (ȕ-,19.7 min) o 214Po (Į, 164 ȝs) o 210Pb (ȕ-, 210
Po/210Pb activity ratios in air at Milford Haven, Wales
22.3 y) (51o40’N, 5o02’E). Lambert et al. (1980) estimated aerosol
Papastefanou, Aerosol and Air Quality Research, 9: 385-393, 2009 391
residence times varied from 8.8 to 10.5 days based on the in 210Po relative to 210Pb. Soil particles are the most likely
210
Bi/210Pb activity ratios in air, while later in another work they contributors, since a part of the tropospheric aerosols originates at
estimated aerosol residence times varied from 7 to 9 days the Earth’s surface. Coal burning and forests fires presumably are
(average 8.58 days) based on the 210Bi/210Pb activity ratios in air, additional sources of radionuclides.
in near Paris, France area during a 6-year period (Lambert et al., Apart of this, Papastefanou (2008) estimated the residence
1983). times of another radionuclide in ambient aerosols, that is 7Be (T
Gäggeler et al. (1995) during an one-year period carried out ½ = 53.3 d) of cosmogenic origin varying between 7.4 and 8.9
measurements on the activities of 214Pb, 210Pb and 212Pb in air at days (average 8 days) at Thessaloniki, Greece (40o38’N, 22o58’E)
high altitude in Jungfraujoch, Switzerland (46o32’N, 07o59’E) as in the category of the lower values of the residence times of
high as 3450 m by using an epiphaniometer. They estimated atmospheric aerosols and leading to the same result for the
aerosol residence times varied between 1 and 12 days (average 6 residence times of radon decay product aerosols in ambient air
days) from the 214Pb/210Pb activity ratios. varying between 4.8 and 15.3 days (average 8.2 days). The
Finally, Rangarajan (1992) based in the 210Bi/210Pb activity method used for the determination of the residence time of 7Be
ratios in air estimated a mean residence time of the natural aerosols was described elsewhere (Papastefanou, 2008).
radioactive aerosols in the planetary boundary layer at Bombay
(Mumbai), India (18o58’N, 72o50’E) around 8 days from forty CONCLUSIONS
three measurements carried out during the long dry period, from
October to May. The aerodynamic size distributions of radon decay product
The data of Table 2 admit residence times of lower values as aerosols in ambient air were measured using low-pressure (LPI)
low as 1.59 days and higher values as high as 320 days. Mostly, and conventional (1-ACFM) and/or high volume (HVI) cascade
the lower IJR-values were resulted from the 210Bi/210Pb activity impactors. Lead-214 and 212Pb were largely associated with
ratios and higher IJR-values from the 210Po/210Pb activity ratios. aerosol particles in the accumulation mode for smaller than 0.52
Low IJR-values were also resulted from the 222Rn/210Pb activity ȝm diameter particles in size. Based on the 46 % low-pressure
ratios. Poet et al. (1972) concluded that longer apparent residence impactor measurements, the mean activity median aerodynamic
time values were based on the 210Po/210Pb activity ratios, than diameter “AMAD” of 214Pb-aerosols was found to be 0.16 ȝm,
those based on the 210Bi/210Pb activity ratios. The difference may while for the 212Pb-aerosols, the mean AMAD was found to be
be explained by the presence of a mixture of aerosols of various 0.12 ȝm. The slightly larger size of 214Pb-aerosol particles
apparent ages, of which older aerosols (those of greater ages) confirmed with operationally different cascade impactors, was
contribute most of 210Po. On the other hand, the solid products of attributed to Į-recoil-driven redistribution of 214Pb following the
radon-decay, that is 210Pb, 210Bi and 210Po might arise from decay of the aerosol-associated 218Po. Even considering recoil
sources other than radioactive decay within the atmosphere. Poet following 214Po Į-decay, the average 210Pb-labelled aerosols grow
et al. (1972) showed that up to 85% of the 210Po in the by a factor of two during its atmospheric lifetime. Estimated
atmosphere is of terrestrial origin, and the vertical profile of 210Po lifetimes of radon decay product aerosols in ambient air resulted
was found to differ appreciably from that expected from the in a mean residence time of about 8 days that could be applied to
decay of 222Rn. Lambert et al. (1979) indicated that volcanic aerosol particles in the lower atmosphere below the boundary
gases are very rich in long-lived radon decay products, especially layer.
392 Papastefanou, Aerosol and Air Quality Research, 9: 385-393, 2009
Suzuki, T., Maruyama, Y., Nakayama, N., Yamada, K. and Ohta, Temporal Variation of 7Be and 210Pb Size Distributions in
K. (1999). Measurement the 210Po/210Pb Activity Ratio in Size Smbient Aerosol. Atmos. Environ. 32: 983-991.
Fractionated Aerosols from the Coast of Japan Sea. Atmos.
Environ. 33: 2285-2288.
Winkler, R., Dietl, F., Frank, G. and Tschiersch, J. (1998). Received for review, February 6, 2009
Accepted, April 10, 2009