DS - 645 - Pro Anticarb HB Elastomeric Coating

Pro Anticarb HB Elastomeric Coating
USES
A water based high build Elastomeric Anticarbonation Coating for protecting the surfaces of pre-stressed and reinforced concrete
members of building exteriors in coastal installations, bridges, exposed to high vehicular gas emissions.
SCOPE
A high solid, high performance water borne Acrylic Elastomeric Coating specially designed to protect exterior concrete providing anti-
carbonation and excellent water vapour diffusion property. The coating in system extends durability of the structurals for its good
crack bridging property and resistance to fungal growth. The product with its very low VOC emmission, qualifies as per LEED
standards.
Conforms to IRC :SP: 80 -2008 Rev 2019 and MoRTH Specification Section 2800 as per guidelines under 2808
PRODUCT DATA RESISTANCE GUIDE
Type : Water Based Acrylic Elastomeric Coating Physical Parameters

Composition : Acrylic resin suitably pigmented with added mineral
Resistance to water: Good
fillers
Application : Brush/ Spray Elongation at break: 200% @ 200µ
Solids Content : 70 ±3% VOC: 60gm/l Scratch Hardness : Passes 1.5Kg @ 100µ DFT
Recommended DFT : 90 - 115 µ per coat Tensile Strength :21 kg/cm2 @ 200 µ
Corresponding WFT: 170 - 217 µ per coat Flexibility : Good
2
Theoretical Spreading Rate: 4.6 to 5.9 m /Ltr /coat Crack Bridging capability: 2mm
Drying Time : Adhesion : Good
TOUCH : < 45 minutes Abrasion Resistance : Very Good
HANDLE : < 6 hours Impact Resistance : Good
HARD : Overnight Diffusion resistance against CO2 : Equivalent air-layer
Over Coating : Min: 2 hours thickness > 50 M
Max: 3 days UV Resistance: Excellent
Colour : White and, select tintable shades
Finish: Matt
Packing: 20 Ltr
Thinner/Cleaner : Potable soft water
Storage Life : Upto nine months as long as the
sealed containers are kept under cover in a dry place DATA SHEET No. : 645
under normal temperature conditions. Issue Date : Dec 2019
Pro Anticarb HB Elastomeric
Coating
SURFACE PREPARATION
Concrete: New Concrete - Ensure that the concrete is cured for minimum 3 months. The surface is to be made
rough and free from laitance and other contaminants by sand sweeping or hard wire brushing, under reference to
SSPC SP 13. Apply primer before applying the finish paint.
The surface moisture content should not exceed 5%.
Old Concrete : Remove all salt deposits from the surface by water jet washing. Light sand blast the surface or hard
wire brush to remove all loosely bound coatings and roughening up of firmly adhering coating to ensure
anchorage with the primer. Ensure all dust/other particles are fully removed by suction or air blast and the surface is
fully cleaned and dry before application of primer.
APPLICATION
Mix the contents thoroughly before and during use.
Brush/Roller : Apply preferably without thinning. If required, add upto 5% soft potable water.
Airless Spray: Apply preferably without thinning. However, if required, add upto 3% of soft potable water if
required. Use any standard airless spray equipment with a 58 : 1 pump ratio with a fluid tip of 21 - 26 thou (0.53 - 0.66
mm) or adjustable tip and an air supply of 690 - 830 kPa (100 - 120 p.s.i.) and a line size of 12 mm ID.
TYPICAL PAINTING SPECIFICATIONS
Surface 1st Coat 2nd Coat 3rd Coat
Pre-stressed and RCC/ PRO Anticarb WB Sealer/ PRO Pro Anticarb HB Pro Anticarb HB
Masonary Surfaces Anticarb Primer WB White Elastomeric Coating Elastomeric Coating
Notes :
1. Do not apply when relative humidity rises above 90% or when the atmospheric temperature falls below 10oC.
2. Do not apply during rain, fog or mist.
Health & Safety : Please refer to the separate Safety Data Sheet available with detailed information.
DISCLAIMER
The information contained within this Data Sheet is based on information believed to be reliable at the
time of its preparation. The Company will not be liable for loss or damage howsoever caused including DATA SHEET No. :
liability for negligence, which may be suffered by the user of the data contained herein. It is the users’ 645
responsibility to conduct all necessary tests to confirm the suitability of any product or system for their Issue Date : Dec 2019
intended use. No guarantee of results is implied since conditions of use are beyond our control.
BERGER PAINTS INDIA LIMITED

Berger House,129 Park Street, Kolkata 700017
Phone : (033) 2229 9724 (5 lines) / 249 9754 (4 lines) Fax : 91-33-2249 9729 / 2249 9009
protectonhelpdesk@bergerindia.com | www.bergerpaints.com

DS - 645 - Pro Anticarb HB Elastomeric Coating

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

DS - 645 - Pro Anticarb HB Elastomeric Coating

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DS - 645 - Pro Anticarb HB Elastomeric Coating

Uploaded by

Copyright:

Available Formats

Pro Anticarb HB Elastomeric Coating

PRODUCT DATA RESISTANCE GUIDE

Type : Water Based Acrylic Elastomeric Coating Physical Parameters

TYPICAL PAINTING SPECIFICATIONS

Surface 1st Coat 2nd Coat 3rd Coat

BERGER PAINTS INDIA LIMITED

You might also like