PAVA Catalog en V5

Public Address - Voice Alarm
ATEI Audio Distribution over IP

Commercial Audio
Intelligent Acoustic Solutions
Intercommunication
Loudspeakers
Public Address & Voice Alarm
D ELIVERING Y OUR M ESSAGE

Ver. 5
ATEIS which boosts 30-years of experience in the
research and development of Public Address and
Voice Evacuation Systems now introduces a new
system that perfectly integrates Fire-Alarm with
Voice-Alarm according to EN 54-16(VACIE&FACIE),
BS 5839-Part 8 and ISO 7240-16, compliance
for large installations and installations with specific
purpose.
IDA8 Digital Public Address and Voice Alarm series is

a 3rd generation modular system that complies with
current architectural demands that required IP-
and/or Fiber-optics Networking to cover for any
complex design possible.
ATEIS has developed and will continue developing

dedicated system for Digital Public Address and
Voice-Alarm applications.
ATEI

IDA8 system Index ATEI
Networkable PAVA System Controller–Matrix Mode
IDA8C 6
Networkable PAVA System–Slave Unit–Matrix Mode
IDA8S 9
Networkable PAVA System–Slave Unit–A/B-zoning–Matrix Mode
IDA8SAB 11
Networkable PAVA System–Lo-Z Slave Unit–Matrix Mode
IDA8SL 14
Networkable PAVA System–Controller / Slave Unit–Switch Mode
IDA8C-SW / IDA8SAB-SW 16
IDA8 Full-Redundancy Switching Unit
RU-MAIN / CTL / PDC 24
ATEÏS Net Secured Audio Network Card / Optional Boards
NET-CX / Optional Boards 26 Public Address
IDA8 System Voice Alarm
Ordering Information 29
ATEÏS Studio
Integrated Operation Software
ATEÏS Studio 30
DIVA8G2 System
Compact PAVA system–Master Unit–Switch Mode
DIVA8MG2 33
Compact PAVA system–Slave Unit–Switch Mode
DIVA8SG2 36
Amplifiers
Digital Power Amplifiers
DPAfour 41
Security Power Amplifiers
SPA 43
Bridging Power Amplifiers
BPA 45
Battery Charger
Charger and Monitoring Unit - EN 54-4
SONAES 47
Consoles & Accessories
Color Touch-Screen Secure Paging Console
PSS AS / PSS G2 / PSS G2E / PPM-IT5 51
Desktop Paging Consoles
PPM AS / PSM 53
Wall-mounted Monitored Touch-screen Paging Console
CD-Touch 56
Wall-mounted Monitored Paging Console
CD8 / CD16 / CDPM / PCP 57
Programmable Remote Controller with Display
URC-AS / URC200 61
Digital Noise Sensing Microphone
DNM 61
Touch Dial Controller / Wireless Transceiver for IDA8 system
DialPad / Wireless Transceiver 62
Alarm Input Interface for IDA8 System and DIVA8G2 System
URGP32in / URGP 16I160 63
Enclosure
List of Peripherals 64
DIVA8 G2 System / Amplifiers / Batter y Charger/Remote Controller
/Alarm Input Interface /Accessories
Ordering Information 65
Audio Distribution over IP ATEI
Commercial Audio
Intercommunication
Loudspeakers IDA8C
Networkable PAVA System

Controller – Matrix Mode
IDA8 is a third-generation modular

system that complies with current
IDA8C-SW architectural demands requiring IP
Controller – Switch Mode
and/or fiber-optic networking to
Pending
allow for even the most complex
of system designs.
IDA8 responds to Public Address

and Voice Alarm requirements as
stated in EN54-16, ISO 7240- 16,
UL60065 and BS5839/8, with
specific attributes for compliance
in large installations.
Commercial Audio
Intercommunication
Loudspeakers
IDA8S

Slave Unit – Matrix Mode
IDA8SAB

Slave Unit – A/B-zoning – Matrix Mode
IDA8SAB - SW
IDA8SL
Slave Unit – Switch Mode
Lo-Z Slave Unit – Matrix Mode
Pending Pending
IDA8 system
Audio Distribution over IP
Commercial Audio
Intercommunication
Loudspeakers
IDA8C
NETWORKABLE PAVA SYSTEM CONTROLLER – MATRIX MODE
IDA8 is a third-generation modular system that complies with current

architectural demands requiring IP and/or fiber-optic networking to
allow for even the most complex of system designs. IDA8C responds
to Public Address and Voice Alarm requirements as stated in EN54-16,
UL60065, ISO 7240-16 and BS5839/8, with specific attributes for
compliance in large installations.
MAIN CHARACTERISTICS CONNECTIVITY:
Support a maximum up to 31 slave units in ATEÏS Local-Net

The IDA8C Controller unit houses advanced audio digital signal processing (DSP),
Up to 256 zones provision via ATEÏS Local-Net
matrix control functions and a digital message player, with front panel access for
Up to 8192 zones provision via ATEÏS Global-Net
a fully monitored fireman’s microphone and emergency message trigger buttons.
IDA8C also supports amplifier monitoring with hot-swap amplifiers and
Fully digital with 8 audio inputs and 8 audio outputs

loudspeaker line impedance monitoring. It can support up to four PSS-AS
4 dedicated and monitored PDC-ports for paging consoles

monitored microphone consoles and up to eight monitored amplifiers plus two
2 dedicated audio in and outputs for back-up amplifiers

back-up amplifiers, paging into 8 different zones per unit with A/B line detection
Enhanced loudspeaker line surveillance for AB-zoned installation
according to BS 5839 part 8. Featuring 8 monitored zones for 25V/70V/100V
Simultaneous control and routing of 48 audio channels over
outputs with simultaneous selection, control inputs, and contact outputs. IDA8C
dedicated network provides the zones and audio in & out expansion of the IDA8 systems, using a
secured 48-channel audio and data network over CAT5 or fiber optic, which can
24bit, 48k sampling digital A/D converter, 32bit DSP

be a network of one controller and a maximum up to 31 Slave units via ATEÏS
Each of the 8 zones offers 1000W (MAX.)

local-net, providing with 256 paging zones with priorities (1~99), satisfying with
25 / 70 / 100V selectable outputs

the most complex public address and voice alarm requirements. Two card slots
Up to 100m by using CAT-5 cable with NET-C1
are provided for either 4-channel 0dB audio input or 4-channel audio cards.
Optional Fiber-optic cards for links up to 20 km
Optional AES/EBU cards are also available.
9 supervised control inputs and 8 control outputs

Each IDA8C input and output channel is fitted with a wide range of pre-and
Modbus Protocol interface via TCP/IP or RS485

post-processing devices such as volume controllers, routing mixers and switches,
Digital storage for up to 100 minutes in WAV format (16k 16 bit) or
priority and paging components, equalizers, compressors, limiters and delay-lines.
400 minutes in G.722 format of pre-recorded messages Digital messaging (G.711, G.722, G.726, G.727 and WAV format) can be stored for
4 message players
live or pre-recorded playback. Digital audio files are uploaded from a computer to
the IDA8C through the user-friendly ATEÏS Studio GUI. Several messages can be
Programmable Message Scheduler Events

played simultaneously into different zones: up to 4 messages from a single IDA8C
DSP functions of PEQ, GEQ, Delays, Ducker, Gate, AGC, feedback, filter,

Controller or a total of 48 messages across an IDA8 system (controller with
inverter, local echo suppressor, mixer slaves). A built-in loudspeaker on the IDA8C allows selective feedback for all
Ethernet interface for TERRACOM, 3rd party devices, configuration,
sources and 100V output signals. One IDA8C can also connect to a maximum up
control, diagnostics and logging to 31 Slave units. The slave units are available as single zone (IDA8S) or with A/B
Incident data record with at least 800 entries (max. 1300)
speaker line configurations (IDA8SAB), or for Lo-Z monitoring (IDA8SL).
Programmable of 4 user levels

The IDA8C Controller unit enables operators to see a detailed overview of the
Telephone interface via SIP protocol or telephone line services
operational status of the entire PA system at the press of a button. It is able to
1 Fault & 1 EVAC relays outputs
run an impedance scan of all components connected to it, covering not only the
Programmable 256 priority paging zones with priority(1~99)
input paging consoles but also cabling, processing blocks such as compressors
and limiters, delay lines, the network and loudspeakers.
2U standard 19" rack mounting

Export the incident log
The IDA8C Controller operates either on 110VAC or 230VAC mains power supply
EN54-16 certified, UL listed
or on a 24V battery power supply for emergency back-up, with automatic switch-
To cooperate with RU devices to do redundancy, external power is
over. Both power supplies are securely monitored. IDA8C is easily configured
using the PC-based ATEÏS Studio global software. Once programmed, the system
requested
will operate independently (off-line) without a PC having to be connected.
ATEI
6
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
IDA8C
INSTALLATION NOTES
SECURITY:
In accordance with EN54-16, UL60065, ISO 7240-16 and BS5839/8, all IDA8 system components and
peripherals are monitored. This monitoring extends from the capsule of a paging station microphone to the
end of a loudspeaker line. The external cables connected to the control inputs are monitored for short and
open circuit and an internally-generated pilot tone is available for monitoring impedance on the
loudspeaker lines.
The system can handle 256 paging zones with priority(1~99), satisfying with the most complex public
address and voice alarm requirements. The controller monitors the status of all the equipment in the
ATEÏS STUDIO system, reports status changes and logs the last 1300 fault messages in the system. The log can be
Design Software For IDA8 accessed on the front-panel IDA8C display or on a PC through ATEÏS Studio.
ATEI
7
IDA8 system
IDA8C
NETWORKABLE PAVA SYSTEM CONTROLLER – MATRIX MODE
CONTROLS AND INDICATORS PARTS INCLUDED Amplifier Capacity (per zone)

Input 1000 W (MAX.)
Front Quantities Components
3.5"
full color touch-screen LCD display 1 IDA8Cxx Controller unit
Monitoring Loudspeaker
EVAC
/ Zone selection buttons 1 Fireman microphone
Input 1< 50 Ohm (Display SHORT)
Fireman
microphone 1 Power cord (type depends on region)
50~5000 Ohm
Status
indicators (Power / Network / System Fault / 1 Set of mounting brackets for 19" rack
(Display Impedance value)
G.Fault / By-Pass Mode / Global Evac / By-pass 1 Set of connectors
1>5000 Ohm (Display OPEN)
Monitoring / Fireman microphone running / Zone 1 ATEÏS Studio software GUI
Fault / Zone Evac Status) 1 LAN Cable
Mechanical
INTERCONNECTIONS TECHNICAL SPECIFICATIONS Dimensions (With 19" rack mount brackets)

(H x W x D) 2RU, 88 x 486 x 313 mm
Front Electrical
(3.5" x 19" x 12-1/3")
Firemen microphone
Mains power supply
Weight 5.36 kg (11.8 lbs)
Rear Voltage 230/115 VAC ±15%, 50/60 Hz
Mounting 19"-rack mount
AC power socket
Power consumption 48 W
Color RAL7016
24VDC backup power input
Fuse Rating 1.6 A
Fault/EVAC/BYPASS
output
Environmental
9 control inputs
Battery power supply
Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
8 control outputs
Voltage 18 - 30 VDC
Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
8 analogue audio mic/line inputs/outputs (Optional)
Amp Consumption 1.4 A
Relative humidity 15% to 90%
Ethernet (100BASE-TX)

Air pressure 600 to 1100 h Pa
Local / Global Network Card (Optional)
Performance
Heat Dissipation 153 BTU/hr
8 amplifier in and outputs
Frequency response ±1 dB @ 20 Hz and 20 kHz
2 connections for backup amplifiers

4 monitored paging console inputs

Line inputs (Optional audio input card)
Telephone Card (Optional)
Connector 3-pin phoenix
CERTIFICATIONS AND APPROVALS
SNR >81 dBA
THD < 0.02% @ 1 kHz
REGIONAL CERTIFICATIONS
Input sensitivity 0~66 dBu / 6dB steps
Europe Voice Alarm EN54-16 certified 2012 Input impedance 10 kohm
CE – 0359
according to EN50130 – 4 Line outputs (Optional audio output card)
Railway EN50121 – 4 Connector 3-pin phoenix
Controller SNR >81 dBA
System THD < 0.02% @ 1 kHz
USA Safety UL60065 Signal 0dB
Output impedance <100 ohm
ATEI
8
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
IDA8S
NETWORKABLE PAVA SYSTEM – SLAVE UNIT – MATRIX MODE
IDA8 is a third-generation modular system that complies with

current architectural demands requiring IP and/or fiber-optic
networking to allow for even the most complex of system designs.
IDA8S responds to Public Address and Voice Alarm requirements as
stated in EN54-16, ISO 7240-16 and BS5839/8, with specific
attributes for compliance in large installations.
CONNECTIVITY: MAIN CHARACTERISTICS

The IDA8S Slave unit houses advanced audio digital signal processing (DSP), matrix Support a maximum up to 31 slave units in ATEÏS Local-Net

control functions and a digital message player, along with amplifier monitoring for Up to 256 zones provision via ATEÏS Local-Net

hot-swap amplifiers and loudspeaker line impedance monitoring. It can support up Fully digital with 8 audio inputs and 8 audio outputs

to two PSS-AS monitored microphone consoles and up to eight monitored

amplifiers plus two backup amplifiers, paging into 8 different zones per unit with

line detection. Featuring 8 monitored zones for 25V/70V/100V outputs with
simultaneous selection, control inputs, and contact outputs. IDA8C provides the Enhanced loudspeaker line surveillance for each zone installation

zones and audio in & out expansion of the IDA8 systems, using a secured 48- Simultaneous control and routing of 48 audio channels over

channel audio and data network over CAT5 or fiber optic, which can be a network dedicated network
of one controller and a maximum up to 31 Slave units via ATEÏS local-net. Two card 24bit, 48k sampling digital A/D converter, 32bit DSP

slots can fitted with optional 4-channel analogue audio input/outputs cards(max

two cards per device).

IDA8S Slave units provides extension of IDA8 system configuration with an Up to 100m by using CAT-5 cable with NET-C1

additional 8 output zones and 2 back-up amplifiers. Each input and output channel Optional Fiber-optic cards for links up to 20 km

is fitted with a wide range of pre- and post-processing devices such as volume

controllers, routing mixers and switches, priority and paging components, equalizers,
Modbus Protocol interface via RS485.

compressors, limiters and delay-lines. Digital messaging (G.711, G.722, G.726, G.727
and WAV format) can be stored for live or pre-recorded playback. Digital audio files Digital storage for up to 50 minutes in WAV format (16k 16 bit) or

are uploaded from a computer to the IDA8S through the user-friendly ATEÏS Studio 200 minutes in G.722 format of pre-recorded messages
GUI. Several messages can be played simultaneously into different zones: up to 4 4 message players

messages from a single IDA8S Slave or a total of 48 message channels across an Programmable Message Scheduler Events

IDA8 system (controller with slaves).
DSP functions of PEQ, GEQ, Delays, Ducker, Gate, AGC, feedback,

The IDA8S Slave operates on a 24VDC power supply. The power supplies is filter, inverter, local echo suppressor, mixer
monitored. The IDA8S Slave also supports redundant loop network cabling. IDA8S is Ethernet interface for TERRACOM, 3rd party devices, configuration,

easily configured using the PC-based ATEÏS Studio global software. Once control, diagnostics and logging
programmed, the system will operate independently (off-line) without a PC having

to be connected.

SECURITY: 1 Fault & 1 EVAC relays outputs


In accordance with EN54-16, ISO 7240-16 and BS5839/8, all IDA8 system com-
ponents and peripherals are monitored. This monitoring extends from the capsule Export the incident log

of a paging station microphone to the end of a loudspeaker line. The external 1U standard 19" rack mounting

cables connected to the control inputs are monitored for short and open circuit and EN54-16 certified

an internal, generated pilot tone is available for monitoring impedance on the To cooperate with RU devices to do redundancy, external power is

loudspeaker lines. The system can handle up to 256 zones with 1~99 priorities,
requested.
satisfying even the most complex public address and voice alarm requirements. The
controller monitors the status of all the equipment in the system, reports status
changes and logs error details. The log can be accessed on the front-panel display
of IDA8C or on a PC through ATEÏS Studio.
ATEI
9
IDA8 system
IDA8S
NETWORKABLE PAVA SYSTEM – SLAVE UNIT – MATRIX MODE
CONTROLS AND INDICATORS PARTS INCLUDED
Front Quantities Components Amplifier Capacity (per zone)

Status LEDs ( Network / Bypass Monitoring /
1 IDA8Sxx Slave unit Input 1000 W (MAX.)
Bypass Mode / G. EVAC / System Fault / G. Fault ) 1 110/220V AC to 24V DC power adapter
Zone LEDs (EVAC / Fault )
1 Set of mounting brackets for 19" rack Monitoring Loudspeaker
Power LEDs
1 Set of connectors Input 1< 50 Ohm (Display SHORT)
50~5000 Ohm
INTERCONNECTIONS TECHNICAL SPECIFICATIONS
Rear Electrical 1>5000 Ohm (Display OPEN)
24VDC mains power input
24 VDC power supply
Fault/EVAC/BYPASS output
Voltage 18 - 30 VDC Mechanical
9 control inputs
Amp Consumption 1.4 A Dimensions (With 19" rack mount brackets)
8 control outputs
(H x W x D) 1RU, 44 x 486 x 285 mm
Performance (1-3/4" x 19" x 11-1/5")
2 Local ATEÏS Network connections
Frequency response ±1 dB @ 20 Hz and 20 kHz Weight 4.2 kg (9.25 lbs)
Mounting 19"-rack mount
2 connections for back-up amplifiers
Line inputs (Optional audio input card) Color RAL7016
Frequency response ±1 dB @ 20 Hz and 20 kHz Environmental
SNR >81 dBA Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
THD < 0.02% @ 1 kHz Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Input sensitivity 0~66 dBu / 6dB steps Relative humidity 15% to 90%
Europe Voice Alarm EN54-16 certified 2012 Input impedance 10 kohm Air pressure 600 to 1100 h Pa
CE – 0359 Heat Dissipation 126 BTU/hr
according to EN50130 – 4 Line outputs (Optional audio output card)
SNR >81 dBA
THD < 0.02% @ 1 kHz
Signal 0dB
ATEI
10
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
IDA8SAB
NETWORKABLE PAVA SYSTEM – SLAVE UNIT – A/B-ZONING – MATRIX MODE
IDA8 is a third-generation modular system that complies with

current architectural demands requiring IP and/or fiber-optic
networking to allow for even the most complex of system designs.
IDA8SAB responds to Public Address and Voice Alarm requirements
as stated in EN54-16, UL60065, ISO 7240-16 and BS5839/ 8, with
specific attributes for compliance in large installations.

The IDA8SAB Slave unit houses advanced audio digital signal processing (DSP), Support a maximum up to 31 slave units in ATEÏS Local-Net

matrix control functions and a digital message player, along with amplifier Up to 256 zones provision via ATEÏS Local-Net

monitoring with hot-swap amplifiers and loudspeaker line-impedance line Fully digital with 8 audio inputs and 8 audio outputs

monitoring. It can support up to two PSS-AS monitored microphone consoles, up to

eight monitored amplifiers plus two backup amplifiers and paging into 8 different

zones per unit with A/B line detection according to the BS 5839-part 8. Featuring 8
monitored zones for 25V/70V/100V outputs with simultaneous selection, control Enhanced loudspeaker line surveillance for AB-zoned installation

inputs, and contact outputs. IDA8C provides the zones and audio in & out Simultaneous control and routing of 48 audio channels over

expansion of the IDA8 Systems, using a secured 48-channel audio and data network dedicated network
over CAT5 or fiber optic, which can be a network of one controller and a maximum 24bit, 48k sampling digital A/D converter, 32bit DSP

up to 31 Slave units via ATEÏS local-net. Two rear card slots can be fitted with

optional 4-channel analogue audio in/output cards 4 channel AES/EBU cards for

digital audio in/out.

IDA8SAB Slave units provides extension of IDA8 system configuration with an Optional Fiber-optic cards for links up to 20 km

additional 8 output zones and 2 back-up amplifiers. Digital messaging can be stored

in the unit for live or scheduled playback. Files are uploaded in G.711, G.722, G.726,

G.727 and WAV format from a computer using the ATEÏS Studio system GUI. Several
messages can be played simultaneously into different zones: up to 4 from a single Digital storage for up to 50 minutes in WAV format (16k 16 bit) or

IDA8SAB or a total of 48 message channels across a full IDA8 system with slaves. 200 minutes in G.722 format of pre-recorded messages
4 message players

Each input and output channel is fitted with a wide range of pre-and post-

processing devices such as volume controllers, routing mixers and switches, priority
and paging components, equalizers, com-pressers, limiters and delay-lines. DSP functions of PEQ, GEQ, Delays, Ducker, Gate, AGC, feedback,

filter, inverter, local echo suppressor, mixer
IDA8SAB is easily configured with PC-based ATEÏS Studio global software. Once

programmed, the system will run independently without a PC connected. The
control, diagnostics and logging
IDA8SAB Slave operates either on 110VAC or 230VAC mains power or on a 24V DC
power supply for emergency back-up, with automatic switchover. Both of the power Incident data record with at least 800 entries (max. 1300)

supplies are monitored. Programmable of 4 user levels


SECURITY:

In accordance with EN54-16, UL60065, ISO 7240-16 and BS5839/8, all system Programmable 256 priority paging zones with priority(1~99)

components and peripherals are monitored. This monitoring extends from the Export the incident log

capsule of a paging station microphone to the end of a loudspeaker line. The

external cables connected to the control inputs are monitored for short and open
EN54-16 certified, UL listed

circuit and an internal, generated pilot tone is available for monitoring impedance
on the loudspeaker lines. The IDA8SAB Slave supports redundant network cabling as To cooperate with RU devices to do redundancy, external power is

a redundant loop. The system can handle up to 256 zones with priority(1~99), requested
satisfying even the most complex public address and voice alarm requirements.
ATEI
11
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
IDA8SAB
INSTALLATION NOTES
ATEI
12
IDA8 system
IDA8SAB
NETWORKABLE PAVA SYSTEM – SLAVE UNIT – A/B-ZONING – MATRIX MODE

1 IDA8SABxx Slave unit Input 1000 W (MAX.)
Bypass Mode / G. EVAC / System Fault / G. Fault ) 1 Power cord (type depends on region)
Power LEDs
50~5000 Ohm
AC power socket
Mains power supply
Voltage 230/115 VAC ±15%, 50/60 Hz Mechanical
BYPASS Mode output
Power consumption 48 W Dimensions (With 19" rack mount brackets)
9 control inputs
Fuse Rating 1.6 A (H x W x D) 2RU, 88 x 486 x 289 mm
8 control outputs
(3-1/2" x 19" x 11-3/8")
Battery power supply Weight 5 kg (11 lbs)
Voltage 18 - 30 VDC Mounting 19"-rack mount
Amp Consumption 1.4 A Color RAL7016
2 connections for back-up amplifiers


Performance Environmental
Frequency response ±1 dB @ 20 Hz and 20 kHz Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Line inputs (Optional audio input card) Relative humidity 15% to 90%
Connector 3-pin phoenix Air pressure 600 to 1100 h Pa
Frequency response ±1 dB @ 20 Hz and 20 kHz Heat Dissipation 140 BTU/hr
Europe Voice Alarm EN54-16 certified 2012 SNR >81 dBA
CE – 0359 THD < 0.02% @ 1 kHz
according to EN50130 – 4 Input sensitivity 0~66 dBu / 6dB steps
Railway EN50121 – 4 Input impedance 10 kohm
Controller
System Line outputs (Optional audio output card)
USA Safety UL60065 Connector 3-pin phoenix
SNR >81 dBA
THD < 0.02% @ 1 kHz
Signal 0dB
ATEI
13
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
IDA8SL
NETWORKABLE PAVA SYSTEM LO-Z SLAVE UNIT – MATRIX MODE
IDA8 is a third-generation modular system that complies with current

architectural demands requiring IP and/or fiber-optic networking to allow
for even the most complex of system designs. IDA8SL responds to
Public Address and Voice Alarm requirements as stated in EN54-
16(Pending), UL60065, ISO 7240-16 and BS5839/8, with specific
Pending
MAIN CHARACTERISTICS CONNECTIVITY:

The IDA8SL Lo-Z Slave unit houses advanced audio digital signal processing (DSP),
Up to 256 zones provision via ATEÏS Local-Net
matrix control functions and a digital message player, along with amplifier monitoring
with hot-swap amplifiers and Lo-Z line monitoring. It can support up to two PSS-AS
monitored microphone consoles, up to four monitored amplifiers plus one backup
1 dedicated audio in/output for back-up amplifier

amplifier and paging into 4 different zones per unit with line detection. Each input
Enhanced loudspeaker line surveillance for each zone installation

and output channel is fitted with a wide range of pre-and post-processing devices
Simultaneous control and routing of 48 audio channels over

such as volume controllers, routing mixers and switches, priority and paging
dedicated network components, equalizers, compressors, limiters and delay-lines.

IDA8SL Slave units provides extension of IDA8 system configuration with an

additional 4 output zones and 1 back-up amplifier. Digital messaging can be stored in

the unit for live or scheduled playback. Files are uploaded in G.711, G.722, G.726,
G.727 and WAV format from a computer using the ATEÏS Studio system GUI. Several
messages can be played simultaneously into different zones: up to 4 from a single
IDA8SL or a total of 48 message channels across a full IDA8 system with slaves.
Modbus Protocol interface via RS485

IDA8SL is easily configured with PC-based ATEÏS Studio global software. Once
Digital storage for up to 50 minutes in WAV format (16k 16 bit) or
programmed, the system will run independently without a PC connected. The IDA8SL-
200 minutes in G.722 format of pre-recorded messages Slave operates either on 110VAC or 230VAC mains power or on a 24V DC power
4 message players
supply for emergency back-up, with automatic switchover. Both of the power supplies
are monitored.

DSP functions of PEQ, GEQ, Delays, Ducker, Gate, AGC, feedback,
SECURITY:
filter, inverter, local echo suppressor, mixer
In accordance with EN54-16(Pending), UL60065, ISO 7240-16 and BS5839/8, all system

components and peripherals are monitored. This monitoring extends from the capsule
control, diagnostics and logging of a paging station microphone to the end of a loudspeaker line. The external cables
connected to the control inputs are monitored for short and open circuit and an
internally generated pilot tone is available for monitoring impedance on the
loudspeaker lines. The IDA8SL Slave supports redundant network cabling as a

redundant loop. The system can handle up to 256 zones with 1~99 priorities,
satisfying even the most complex public address and voice alarm requirements.


UL listed

To cooperate with RU devices to do redundancy, external power is

requested
ATEI
14
IDA8 system
IDA8SL
NETWORKABLE PAVA SYSTEM LO-Z SLAVE UNIT – MATRIX MODE

1 IDA8SLxx Slave unit Input 1500 W (MAX.)
Power LEDs
1 Set of connectors Input >0, <5000 Ohm
>5000 Ohm (Display OPEN)
Rear Electrical
AC power socket
Mains power supply Mechanical
Voltage 230/115 VAC ±15%, 50/60 Hz Dimensions (With 19" rack mount brackets)
BYPASS Mode output
Power consumption 48 W (H x W x D) 2RU, 88 x 486 x 300 mm
9 control inputs
Fuse Rating 1.6 A (3-1/2" x 19" x 11-4/5")
8 control outputs
Weight 4.2 kg (9.25 lbs)
Battery power supply Mounting 19"-rack mount
4 low-impedance amplifier in and outputs
Voltage 18 - 30 VDC Color RAL7016
1 connection for back-up amplifiers
Amp Consumption 1.4 A
Environmental
Performance Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Frequency response ±1 dB @ 20 Hz and 20 kHz Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Relative humidity 15% to 90%
Line inputs (Optional audio input card) Air pressure 600 to 1100 h Pa
Europe Voice Alarm EN54-16 certified(Pending) Connector SPEAKON (electronically balanced) Heat Dissipation 140 BTU/hr
CE – 0359 Frequency response ±1 dB @ 20 Hz and 20 kHz
according to EN50130 – 4 SNR >81 dBA
USA Safety UL60065 THD < 0.02% @ 1 kHz
Input sensitivity 0~66 dBu / 6dB steps
Input impedance 10 kohm
Line outputs (Optional audio output card)

Connector XLR
SNR >81 dBA
THD < 0.02% @ 1 kHz
Signal 0dB
ATEI
15
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
IDA8C-SW
NETWORKABLE PAVA SYSTEM CONTROLLER – SWITCH MODE
Pending
IDA8C-SW supports up to 4 audio sources including Evac/ Voice/ Music/ Backup, MAIN CHARACTERISTICS
utilizing with a maximum capacity of 1000 W for each and the choice of audio

source can be selected from one source only for the systems. Featuring 8
monitored zones for 25V/70V/100V outputs with simultaneous selection, control Up to 8192 zones provision via ATEÏS Global-Net

inputs, and contact outputs. IDA8C-SW provides the zones and audio in & out Fully digital with 8 audio inputs and 8 audio outputs

expansion of the IDA8C-SW Systems, using a secured 48-channel audio and data 4 x 1000 Watt maximum load

network over CAT5 or fiber optic, which can be a network of one controller and 4 channel audio distribution for EVAC, Paging, BGM & Backup

a maximum up to 31 Slave units via ATEÏS local-net, providing with 256 paging Combined back-up amplifier function

zones with priorities (1~99). Furthermore, IDA8C-SW is capable to expand up to

8192 zones via ATEÏS global-net, satisfying with the most complex public address
and voice alarm requirements. Enhanced loudspeaker line surveillance for AB-zoned installation

Simultaneous control and routing of 48 audio channels over dedicated

The IDA8C-SW requires up to 4 channel amplifier and be capable to act as a network
backup amplifier in case other amplifiers break down. In case of evacuation, the

zones attenuators will be bypassed automatically and signal output shall be
activated when certain zone is occupied with a source that has a higher priority Up to 100m by using CAT-5 cable with NET-C1

than the music alarm or voice paging. Two card slots are provided for either 4- Optional Fiber-optic cards for links up to 20 km

channel 0dB audio input or 4-channel audio cards. Optional AES/EBU cards are Modbus Protocol interface via TCP/IP or RS485

also available. Digital storage for up to 100 minutes in WAV format (16k 16 bit) or 400

IDA8C-SW Controller unit is capable to run an impedance scan of all the minutes in G.722 format of pre-recorded messages
components, covering not only the input paging consoles but the cabling, and 4 message players

processing blocks such as compressors and limiters, delay lines, network and Programmable Message Scheduler Events

loudspeakers. Digital messaging (G.711, G.722, G.726, G.727 and WAV format) can DSP functions of PEQ, GEQ, Delays, Ducker, Gate, AGC, feedback, filter,

be stored for live or pre-recorded playback. It stores a reference measurement of inverter, local echo suppressor, mixer
the system as users create a given configuration. This reference will be

subsequently stored in the system. Any alterations of this configuration will be
reported and logged in an event log file as well. The custom setting of threshold control, diagnostics and logging
shall be applied in it, allowing users to meet each circumstances. Incident data record with at least 800 entries (max. 1300)


Password protecting to the software allows you to protect all recorded data file

which shall be consulted both on the front LCD display panel and in the ATEÏS-
Studio global version software (Windows compatible) via the PC. Once 1 Fault & 1 EVAC relays outputs

programmed, the system enables to work independently(off-line) without the Programmable 256 priority paging zones with priority(1~99)

need of connecting to the PC. Also, any detected fault shall be signaled by a Export the incident log

general fault on the front panel of IDA8C-SW Controller unit. 2U standard 19" rack mounting

IDA8C-SW controller unit enhances the abilities to connect with the touch panel UL listed

microphone consoles (PSS-AS) and programmable transfer contacts. As well as to To cooperate with RU devices to do redundancy, external power is

support the system operation via PC, or 3rd party control such as Crestron or requested
AMX and other control systems to meet users' demands.
ATEI
16
IDA8 system
IDA8C-SW
NETWORKABLE PAVA SYSTEM CONTROLLER – SWITCH MODE

3.5" full color touch-screen LCD display
1 IDA8Cxx-SW Controller unit Input 1000 W (MAX.)
EVAC / Zone selection buttons
1 Fireman microphone
Fireman microphone
1 Power cord (type depends on region) Monitoring Loudspeaker
Status indicators (Power / Network / Bypass /
1 Set of mounting brackets for 19" rack Input 1< 50 Ohm (Display SHORT)
Monitoring / G. EVAC / G. Fault) 1 Set of connectors 50~5000 Ohm
1 ATEÏS Studio software GUI (Display Impedance value)
INTERCONNECTIONS
1 LAN Cable 1>5000 Ohm (Display OPEN)
Front
TECHNICAL SPECIFICATIONS
Firemen microphone
Mechanical
Rear Electrical Dimensions (With 19" rack mount brackets)
AC power socket
Mains power supply (H x W x D) 2RU, 88 x 483 x 305 mm
Voltage 230/115 VAC ±15%, 50/60 Hz (3-1/2" x 19" x 12")
Fault/EVAC/BYPASS output
Power consumption 48 W Weight 6.2 kg (13.65 lbs)
9 control inputs
Fuse Rating 1.6 A Mounting 19"-rack mount
8 control outputs
Color RAL7016
Ethernet (100BASE-TX)
Voltage 18 - 30 VDC Environmental
Local / Global network in/out card
Amp Consumption 1.4 A Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
4 amplifier inputs and outputs
Performance Relative humidity 15% to 90%
BNC (Optional with AES-EBU)
Frequency response ±1 dB @ 20 Hz and 20 kHz Air pressure 600 to 1100 h Pa
Line inputs (Optional audio input card)
SNR >81 dBA
Europe Voice Alarm EN54-16 certified(Pending) THD < 0,02% @ 1 kHz
CE – 0359 Input sensitivity 0~66 dBu / 6dB steps
according to EN50130 – 4 Input impedance 10 kohm
USA Safety UL60065
SNR >81 dBA
THD < 0,02% @ 1 kHz
Signal 0dB
ATEI
17
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
IDA8SAB - SW
NETWORKABLE PAVA SYSTEM – SLAVE UNIT – SWITCH MODE Pending
IDA8SAB (switch mode) supports up to 4 audio sources including Evac/ Voice/ Music/ Backup,
utilizing with a maximum capacity of 1000 W for each and the choice of audio source can be
selected from one source only for the systems. Featuring 8 monitored zones for 25V/70V/100V
outputs with simultaneous selection, control inputs, and contact outputs. IDA8SAB (switch mode)
provides the zones and audio in & out expansion of the IDA8 Systems, using a secured 48-
channel audio and data network over CAT5 or fiber optic, which can be a network of one
controller and a maximum up to 31 Slave units via ATEÏS local-net, providing with 256 paging
MAIN CHARACTERISTICS zones with priorities (1~99). Two rear card slots can be fitted with optional 4-channel analogue
Support a maximum up to 31 slave units in ATEÏS
audio in/output cards 4 channel AES/EBU cards for digital audio in/out.
Local-Net IDA8SAB (switch mode) requires less number of amplifiers with only 4 audio inputs / outputs
Up to 8192 zones provision via ATEÏS Global-Net
(EVAC/ Voice/ Music/ Back up) from amplifier and be capable to act as a backup amplifier in case
Fully digital with 8 audio inputs and 8 audio outputs
other amplifiers break down. Users shall manually route the signal and digital messages into the
4 x 1000 Watt maximum load
selected zones and adjust the audio level, switch the music (ON/OFF)...etc. In case of evacuation,
the zones attenuators will be bypassed automatically and signal output shall be activated when
4 channel audio distribution for EVAC, Paging, BGM &

certain zone is occupied with a source that has a higher priority than the music alarm or voice
Backup
paging.
Combined back-up amplifier function

2 dedicated and monitored PDC-ports for paging
IDA8SAB (switch mode) slave unit is a user-friendly device which shall be configured via PC
based on ATEÏS Studio global version software (Windows compatible) and password protecting to
consoles
the software allows you to protect your data. Once programmed, the system enables to work
Enhanced loudspeaker line surveillance for AB-zoned

independently(off-line) without the need of connecting to a PC. Also, any detected fault shall be
installation signaled by a general fault. IDA8SAB (switch mode) Controller enhances the abilities to connect
Simultaneous control and routing of 48 audio channels
with the touch panel microphone consoles (PSS-AS) and programmable transfer contacts as well
over dedicated network as support to operate the system via PC, or 3rd party control such as Crestron or AMX and other
control systems to meet the users' demands. Also any detected faults and alarm status are
signaled by general fault and alarm output contacts. A local loudspeaker enables selective

listening to all the sources and the system’s output signals.

All these features make IDA8SAB (switch mode) the ideal system for shopping malls, hotels,
Digital storage for up to 50 minutes in WAV format
restaurants, museums and many other public places.
(16k 16 bit) or 200 minutes in G.722 format of pre-
recorded messages

DSP functions of PEQ, GEQ, Delays, Ducker, Gate, AGC,

feedback, filter, inverter, local echo suppressor, mixer
Ethernet interface for TERRACOM, 3rd party devices,

configuration, control, diagnostics and logging


Telephone interface via SIP protocol or

telephone line services

Programmable 256 priority paging zones with

priority(1~99)


UL listed

To cooperate with RU devices to do redundancy,

external power is requested
ATEI
18
IDA8 system
IDA8SAB- SW
NETWORKABLE PAVA SYSTEM – SLAVE UNIT – SWITCH MODE

1 IDA8SABxx-SW Controller unit Input 1000 W (MAX.)
Power LEDs
50~5000 Ohm
AC power socket
Mains power supply
Voltage 230/115 VAC ±15%, 50/60 Hz Mechanical
BYPASS Mode output
Power consumption 48 W Dimensions (With 19" rack mount brackets)
9 control inputs
Fuse Rating 1.6 A (H x W x D) 2RU, 88 x 483 x 305 mm
8 control outputs
3-1/2" x 19" x 12"
Battery power supply Weight 5.5 kg (12.1 lbs)
2 system LOCAL-network connections
Voltage 18 - 30 VDC Mounting 19"-rack mount
4 amplifier inputs and outputs
Amp Consumption 1.4 A Color RAL7016
BNC (Optional with AES-EBU)


Performance Environmental
Frequency response ±1 dB @ 20 Hz and 20 kHz Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Line inputs (Optional audio input card) Relative humidity 15% to 90%
Connector 3-pin phoenix Air pressure 600 to 1100 h Pa
Frequency response ±1 dB @ 20 Hz and 20 kHz Heat Dissipation 140 BTU/hr
Europe Voice Alarm EN54-16 certified(Pending) SNR >81 dBA
CE – 0359 THD < 0,02% @ 1 kHz
according to EN50130 – 4 Input sensitivity 0~66 dBu / 6dB steps
USA Safety UL60065 Input impedance 10 kohm

SNR >81 dBA
THD < 0,02% @ 1 kHz
Signal 0dB
ATEI
19
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
INSTALLATION EXAMPLES
IDA8C (Switch Mode) system requires and processes four 0 dB audio inputs into only a 4-channel amplifier (Evacuation, Voice, Music or Backup), each input is
also fitted with volume controls and equalizers. The four channels can be switched ON/OFF in each zone separately. In case of Evacuation, the three channels
can be used as a second alarm channel. There are three types of mode (Equal Mode, Unequal Mode, Backup Sharing Mode) which provide users with a
multi-functional combination for preference.
Figure 1: Equal Mode Configuration

EQUAL MODE
In this example of Equal Mode, the master unit
IDA8C (Switch Mode) is linked up with slave units
IDA8SAB(Switch Mode) by Local ATEÏS Local-Net and
contains a secured paging facility with full power
back-up. Each channel can handle up 1000 W audio
power at 100 V and be supplied not only for the
master unit but also the slave units in each zone
simultaneously. Furthermore, there are regular orders
for priority backing-up system (EVAC > Voice >
Music > Backup). For instance, when the EVAC and
Voice amplifiers break down, the Backup and Music
amplifier will automatically switch to EVAC and Voice
amplifiers in order to provide and maintain the
urgent operating paging.
UNEQUAL MODE
Figure 2: Unequal Mode Configuration
In this example of Unequal Mode, the master unit
IDA8C(Switch Mode) is linked up with slave units
IDA8SAB(Switch Mode) by Local ATEÏS Local-Net and
contains a secured paging facility with full power
back-up. It divides the four channels into two
groups and the two channels in each group can be
used for the other backup amplifier in case of
amplifier failure. With ATEÏS Studio software, pro-
viding the function of separating the two groups
with different coverage from 1~99 of priority
automatically.
Priority 1~20 sources shall be used by the EVAC and

Backup channels; Priority 21~99 sources shall be
used by the Voice and Music channels. In case you
might face the possibility when the two amplifiers
for Voice and Music sources are being occupied, the
rest amplifiers for EVAC and Backup channels shall
also be used as the Voice and Music sources
simultaneously with one condition that there are
other vacant amplifiers for EVAC and Backup.
Note: Make sure the Watt unit of each group must

be in the same power capacity.
ATEI
20
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
Figure 3: Backup Sharing Mode Configuration

BACKUP SHARING MODE
In this example of Backup Sharing Mode, the master
unit IDA8C (Switch Mode) is linked up with slave
units IDA8SAB (Switch Mode) by Local ATEÏS Local-
Net and contains a secured paging facility with full
power back-up. The three amplifiers supply for each
zone with one amplifier individually and the backup
amplifier shall be a backup for the three amplifiers
once they break down and switch on the power
supply automatically.
SCENARIOS
By the ATEÏS local-Net which can be a network of one controller and a maximum up to 31 IDA8S/SL/SAB/SAB-SW Slave units in a local system, the system
connects with ATEÏS Local-Net shall be able to link up with each other in different kinds of mode(Equal, Unequal, Backup Sharing). The following pictures
below would give users a better understanding of how to combine the multiple modes together in two or more buildings.
Scenario 1: [Equal Mode + Unequal Mode]
ATEI
21
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
Scenario 2: [Backup Sharing Mode + Equal Mode]
Scenario 3: [Unequal Mode + Backup Sharing Mode]
ATEI
22
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
Scenario 4: [Multiple wiring with 8 amplifiers + Equal Mode]
Scenario 5: [ IDA8C ( Matrix Mode ) + IDA8C / IDA8SAB ( Switch Mode ) ]
ATEI
23
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
RU-MAIN / CTL / PDC

IDA8 FULL-REDUNDANCY SWITCHING UNIT
In place of highly sensitive and secured integration such as nuclear power centrals, underground industrial systems or places where people have to thrust on
a 100% availability of a PAVA system may requires additional full-redundancy system. Redundancy is a very widely-spread application that needs to be
further specified into a required level of redundancy. Compared to the higher levels of redundancy which requires for A/B wiring of the loudspeaker lines
where loss of the A or B line or system still ensures a minimum coverage of 50% of the venue, spare amplifiers and surveillance of essential components in
normal PAVA systems aren't capable to support emergency cases. At this high level of redundancy, not only the amplifiers have redundancy by means of
active spare amplifiers, but also the central equipment will provide a full back-up. And this is what we call: Full-Redundancy. ATEÏS RU, the thorough
switching devices ,providing the high level of redundancy and acting as a Primary / Secondary switching device for IDA8C Controller and IDA8SAB Slave unit.
Here are the three types of devices listed below,
RU-Main: Switching unit for digital audio processing with paging console interface.
RU-CTL: Switching unit for secured input and normal output contacts.
RU-PDC: Switching unit for auxiliary audio IN and OUT contacts with paging console & telephone line interface.
RU device is a device supplied with full-redundancy for audio processor. RU device is in charge of switching primary and secondary audio processor to active
one of them. If primary audio processor is active, all signal of peripherals shall be redirected to the primary audio processor by RU device. RU device is also
capable to monitor the status of audio processor. If primary audio processor breaks down, RU device will detect automatically and switch to secondary audio
processor.
ATEI
24
IDA8 system
RU-MAIN / CTL / PDC

IDA8 FULL-REDUNDANCY SWITCHING UNIT
CONTROLS AND INDICATORS
Front LED display: power, Primary IDA8 system active,

Mechanical
Primary Active Indicator
Secondary IDA8 system Active Dimensions (With 19" rack mount brackets)
Secondary Active Indicator
Control inputs: Primary IDA8 system watchdog,
(H x W x D)
Fault Indicator
Secondary IDA8 system watchdog RU-MAIN 2RU, 88 x 436 x 150 mm
Power Indicator
Control outputs: Primary IDA8 system active,
(3-1/2" x 17-1/5" x 5-9/10")
Secondary IDA8 system Active, Expansion RU-CTL/PDC 1RU, 44 x 436 x 150 mm
INTERCONNECTIONS
(1-3/4" x 17-1/5" x 5-9/10")
PARTS INCLUDED
RU-MAIN Weight
8 speaker lines, 8 amplifiers, 2 backup amps,
Quantities Components RU-MAIN 4.5 kg (10 lbs)
2 PSS inputs, 2 record Out 1 RU-xx unit RU-CTL/PDC 2.5 kg (5.5 lbs)
Switching: Electrical mechanical relays
1 Power cord (type depends on region) Mounting 19"-rack mount
Switching time: 6 seconds (IDA8 watchdog period)
Color RAL7016
Connections: RJ 45, Screw terminals blocks

LED display: power, Primary IDA8 system active,

Electrical Environmental
Secondary IDA8 system Active Power supply Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Voltage 24 VDC Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Secondary IDA8 system watchdog Power consumption Relative humidity 15% to 90%
RU-MAIN 600mA Air pressure 600 to 1100 h Pa
Secondary IDA8 system Active, Expansion RU-CTL 200mA Heat Dissipation
RU-CTL RU-PDC 350mA RU-MAIN 50 BUT/hr
8 x Output contacts, 9 x alarm inputs
RU-CTL 16 BUT/hr
RU-PDC 28 BUT/hr

Connections: Screw terminals blocks

RU-MAIN
LED display: power, Primary IDA8 system active,

Secondary IDA8 system Active


Secondary IDA8 system watchdog


Secondary IDA8 system Active, Expansion

RU-PDC RU-PDC
8 x 0dB inputs or outputs , 2 PSS inputs,

2 Tel inputs


RU-CTL
Connections: RJ 45, Screw terminals blocks

ATEI
25
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
NET - CX
ATEÏS NET SECURED AUDIO NETWORK CARD
ATEÏS Net™ is a secured (monitored) audio network, developed and supplied for fast and low-
latency audio and data transport over a redundant copper (CAT-5) or fiber-optic network ring. ATEÏS
Net™ has an open-architecture design and interfaces with remote devices such as paging
consoles, audio break-in and break-out convertors and room controllers, providing the best solution
to medium to large-scale installations, such as shopping malls, retail stores, train stations and
airports.
ATEÏS Net™ secured audio network responds to Public Address and Voice Alarm requirements as
stated in EN54-16, UL60065, ISO 7240-16 and BS5839/8, with specific attributes for compliance in
large installations.
MAIN CHARACTERISTICS
ATEÏS Net™ audio and data secured network
FUNCTIONS:
Local-net & Global-net

ATEÏS Net™ is able to simultaneously transport 48 audio channels (32 bit, 48 kHz sampling rate) with a
32 x 32 IDA8 system units in a Global network
latency <1ms together with the necessary control data over a CAT-5 or fiber-optic dedicated network.
Low-latency <1ms
For LOCAL and GLOBAL system networking, optional ATEÏS Net™ networking cards can be installed into
48-audio channels
the IDA8 Controller and Slave units. Thanks to its loop architecture, the ATEÏS Net™ audio network is
fully redundant. When a fault (line open or shorted) occurs on a loop segment, it will be automatically
Redundant loop architecture

isolated without affecting the entire system functionality. ATEÏS global-net, can be a network of more
32 bit, 48 kHz sampling
than one controller(Matrix Mode and Switch Mode) and a maximum up to 31 IDA8Sxx Slave units
CAT-5 for up to 100 m
(Matrix Mode and Switch Mode) in a local system.
Fiber-optic multi-mode for up to 2 km

As network addresses are auto negotiated, network setup is very easy. Once programmed, the system
Fiber-optic single-mode for up to 20 km
will operate independently without connecting to a PC having to be connected. 32 IDA8 system units
Dedicated network
can be a network in ATEÏS Global-Net, and each system includes one control unit connecting to 31
EN54-16 certified

slave units in ATEÏS Local-Net.
The installation of NET-C1 cards (RJ45 to RJ45) are suitable with a maximum distance up to 100m
between Matrix and Slave unit or Slave and Slave unit. For longer installation distances, optional NET-
C2, C3 or C4 can be used to extend distances with fiber-optic, up to 2 km between units in multi-
mode or 20 km in single-mode.
Note:
Port A = network IN
Port B = network OUT
NET-C1, 2x RJ45 Port A & Port B
NET-C3, 2x fiber Port A & Port B NET-C4, 1x fiber Port B & 1x RJ45 Port A
NET-C2, 1x RJ45 Port B & 1x fiber Port A
ATEI
26
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
NET - CX
ATEÏS NET SECURED AUDIO NETWORK CARD
TECHNICAL SPECIFICATIONS SECURITY:
In accordance with EN54-16, UL60065, ISO 7240-16 and BS5839/8, all IDA8 system components and
Electrical
peripherals on the ATEÏS Net™ secured audio network are monitored and reports stored in the IDA8C
Battery power supply system controller. The controller monitors the status of all the equipment in the system, reports status
Voltage Internal multi-power socket changes and stores fault messages for recall either on the controller front-panel display or through the
Power consumption 5W ATEÏS Studio PC-based software.
Performance
Frequency response 20 Hz ~ 22 kHz
Sampling rate 32 bit / 48 kHz
Latency < 0.08 ms per node
Integrity assurance Watchdog
Center Wavelength (Fiber-optic)

Multi-mode 1300 nm
Single-mode 1310 nm
FO connector type Straight Tip

FO cable baud rate 62.5 um (Multi-mode)
9 um (Single-mode)
Indicators
LED Network active
LED Network present
ATEÏS Local Net and ATEÏS Global Net
Mechanical
(H x W x D) 18 x 100 x 150 mm
CONTROLS AND INDICATORS CERTIFICATIONS AND APPROVALS
(7/10" x 4" x 6")
Front
Environmental Data running indicator

Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF) Net-work present indicator

Europe Voice Alarm EN54-16 certified 2012
Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF) CE – 0359
INTERCONNECTIONS
Relative humidity 15% to 90% according to EN50130 – 4
Air pressure 600 to 1100 h Pa Front
Two system network connections either CAT5 or

PARTS INCLUDED
Fiber-optic or a combination
Quantities Components
1 ATEÏS Net™ secured audio
network card
1 Set of interconnecting ribbon cables
1 Set of mounting pillars
ATEI
27
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
OPTIONAL BOARDS
Analog Audio I/O Cards: Digital Audio I/O Cards Specialty Cards
Analog audio cards are available for local inputs The digital audio I/O cards allow you to go all the How can a multi-project integrate in both PAVA
or outputs in blocks of 4 or in a 2 in/2 out way to digitize, presenting with the maximum system and conference rooms? By adding the
configuration. Highly adjustable for sensitivity and sound quality and transmission distance on IDA8 Telephone Card which successfully achieves the
output power. An outstanding design with the platform. Digital cards enhance a higher capacity teleconferencing capabilities on IDA8 platform.
maximized flexibility by providing with true 48V of input & output configuration with up to 8
phantom power for each card. channels in and 8 channels out on a single card.
Input Audio Board AES/EBU Card Telephone Card

(Mono Input / Output, Stereo
4 Channels of analog audio inputs
Initiate outgoing calls:
Input / Output, Duplex Stereo)
3 pin Euroblock
- DTMF tone dialing
Mono Input / Output : 4 channels audio input

0, 12, 24, 40, 54dB sensitivity levels
- Speed-dialing
and 4 channels output of digital audio, Stereo
Signal, RTO, overload indicators
- Redial
Input / Output: 2 Channels audio input (2 x 2)
+48V phantom Power
- Flash (3-way telephone conversation)
and 2 channels output of digital audio (2 x 2),
-60 to +20dB fiber range for level
Manual or auto answer incoming call

Duplex Stereo (2 CH for each channel): 4
-50 to +20dB overload threshold
(optional N times)

channels audio input (1,2 CH) and 2 channels
Mute and bypass signal control
Touch-tone decoding

outputs of digital audio (3,4 CH)
Volume display for each channel
Caller ID reception

3 pin Euroblock

RoHS compliant
Disable Hang up sound / Noise Suppression /

RTO / Overload / Signal Indicators

Line Echo Cancellation / Voice Enhance signal
-20 to + 20 dB for overload threshold

control
-60 to + 20 dB fiber range of level

Continuous Line Status and Fault Monitoring

Level control

Mute and level control for caller voice and


ring tone
Mute and bypass control

Various way to control telephone module:

Digital transmission can be reach 100 meter

- Control signal from logic components
RoHS compliant

- External keypad remote controller
Output Audio Board
- Software control panel
4 channels of analog audio outputs
- 3rd party command via RS232 or Ethernet
3 pin Euroblock
Extensive customization options and

Signal, overload indicators
parameters
-60 to +20dB fiber range for level
RoHS compliant

-20 to +20dB overload threshold

Mute and bypass signal control


RoHS compliant

ATEI
28
29
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
ATEÏS Studio
INTEGRATED OPERATION SOFTWARE
ATEÏS Studio is a user-friendly graphic user interface designed for intuitive system setup. The PC-
based software allows hardware updating, full system configuration and generates the user
interface for day-to-day system operation.
GRAPHICAL USER INTERFACE:
ATEÏS Studio allows complete PAVA/audio systems incorporating a range of devices to be configured,
monitored and controlled centrally from a single user interface. ATEÏS Studio supports all IP-based
products within the ATEÏS product family such as IDA8, LAP-AS and ECS. The software enables a
comprehensive overview of the system and its virtual connections and also offers control and
configuration for power amplifiers, paging consoles and remote controllers such as PSS-AS, CD16-AS
and URC-AS devices.
Configuration software
Runs on Windows

Assignable access levels with rights management

All system and unit parameters can be configured

Easy navigation

Drag & Drop features

Real-time monitored

DIAGNOSING:
Diagnostic and logging software
ATEÏS Studio monitors, controls, logs and reports a range of events. The whole system configuration
preset can be stored and reloaded at the press of a button, depending on application. Users can tailor Call, fault and general event logging

design elements of the graphic user interface or control panels, as well as program automatic On-line logging function

sequences of events and create different levels of user access for security and rights management.
Historical logging

BUILDING: Event display priority can be changed

Password-protected

ATEÏS Studio provides a complete set of tools and building blocks for real-time control, monitoring and
design of an audio system or Voice Evacuation system from paging console to loudspeaker. Detailed
information such as signal levels, loudspeaker impedance, pre-recorded messages, amplifier conditions
File transfer software
and other parameters can be monitored in real-time. PC-based application

A comprehensive library of tools, control and monitoring elements is provided along with the GUI, Supplied together with the network controller

including items such as volume control faders, metering, high-level EQ, compression, limiting, auto-gain, Creation of message sets

noise sensing, mixing, shortcut buttons and display elements. Element behavior can be fully tailored to Off-line configuration

suit each application. Built-in file transfer software transfers both data and audio files from the PC to
the network controller.
NOTE:
ACCESS LEVELS:
ATEÏS Studio Software Version:
Additional security can be added to the software with password-protected layers according to EN 54-
16. Multiple users can be created and assigned, each with a unique password and access to specific Version 1.X.X.XX for ATEÏS Local-Net
layers of the GUI. This creates a control surface specific which meets the need of system designers and
Version 3.X.X.XX for ATEÏS Global-Net
operators at multiple levels.
ATEÏS global-net System:
ATEÏS global-net, can be a network of more

than one controller(Matrix Mode and Switch
Mode) and a maximum up to 31 IDA8Sxx
Slave units (Matrix Mode and Switch Mode)
in a local system.
ATEI
30
IDA8 system
Commercial Audio
Intercommunication
Loudspeakers
ATEÏS Studio
POWERFUL DIGITAL SIGNAL PROCESSING
ATEÏS designs and manufactures the leading products in the digital public address & voice alarm
systems market. A highly demanding public transportation network is installed into IDA8-series in
Europe, United States, Asia, the Middle East and global market where it is dominating the market for
high-tech audio communication solutions that combine redundant networks on CAT5, Fiber-optic and
TCP-IP.
IDA8-series of products is the ideal choice for commercial audio applications where schedule events
and background music are an integrated part of the voice-alarm, low-Z sound system. Both applications
guarantee for superb quality of sound and intelligibility. IDA8-series of products are complied with the
EN54-16, UL60065, ISO 7240-16 and BS5839/8
Drag & Drop: Matrix Mixer:
After the determination of the devices included in Breakthrough feedback cancellation -Correcting
your system, you can start configuring the internal feedback and alleviates the annoyance auto-
signal paths independently for each device with all matically. The feedback component analyzes and
the existing features that the huge component library detects the feedback source and adaptively
have offered. Simply by Drag & Drop and connects to attenuates the responsible frequency. There are 4
different audio components. types of feedback components which are
corresponded to the numbers of filters (4, 8 12 or
The all-in-one manipulating platform enhances an 16) that the feedback will use.
easy-to-use and real-time monitored tool, helping you
to concentrate on creating the cutting-edge Auto Noise Gain (A.N.G.) / DNM:
technology.
Featuring an integrated real-time frequency
analyzer and flexible per-channel, which makes a
excellent performance in a variety of operating
environments. Configuring and adjusting the
dynamic equalization bands can be easily done by
its delectated interface.
Page Control:
Some applications which are integrated in PAVA

system require a huge number of zones for
paging. It needs to be done with multiple ATEÏS
VOIP: audio processors (Matrix mode and Switch Mode)
IDA8 system, supporting VoIP based on SIP protocol connected together via ATEÏS Net. The Network
and Audio over IP applications by using PPM-IT5 Paging component provides the capabilities of
paging remote which makes an ideal and simple routing the input source signal to zones and each
solution for bridging audio and contact closures over source can specify which zone wants to page by
long distance LAN and WAN network. Efficiency and its priority value.
reliability are the unique features we have succeeded,
Telephone Card:
even dial-up users can experience the excellent sound
quality. The Telephone Card component is based as a
traditional telephone interface which manages the
telephone call for IDA8 system. The telephone
card component consists of a TC transmit
component and a TC receive component,
providing with dial, receive, detect the logic signal
response of DTMF status.
ATEI
31
Commercial Audio
Intercommunication
DIVA8MG2
Loudspeakers
Compact PAVA system
Master Unit – Switch Mode
DIVA8G2 system is a compact

PAVA solution specifically design-
ed for small to medium-scale
installations. It has all the
essential functionality to comply
with EN-54 requirements for
DIVA8SG2
Voice Alarm, including full system
Compact PAVA system
monitoring, loudspeaker line Slave Unit – Switch Mode
impedance surveillance, micro

phone surveillance and monitored
interfacing with remote devices.
DIVA8G2 responds to Public
Address and Voice Alarm require-
ments as stated in EN54-16, ISO
7240-16 and BS5839/8, with
specific attributes for compliance
in large installations.
DIVA8G2 system
Commercial Audio
Intercommunication
Loudspeakers
DIVA8MG2
COMPACT PAVA SYSTEM – MASTER UNIT – SWITCH MODE
DIVA8G2 system is a compact PAVA solution specifically designed for small to medium-
scale installations. It has all the essential functionality to comply with EN 54 requirements
MAIN CHARACTERISTICS for Voice Alarm, including full system monitoring, loudspeaker line impedance surveillance,
8-zone system controller with individual volume

microphone surveillance and monitored interfacing with remote devices.
DIVA8G2 responds to Public Address and Voice Alarm requirements as stated in EN54-16,
controls per channel
ISO 7240-16 and BS5839/8, with specific attributes for compliance in large installations.
5 audio inputs (2 x line, 1 x MIC/line, 1 x PSS or PSM,

1 x Fireman Mic)
CONNECTIVITY:
1000 Watts maximum load / 100V line outputs per

channel amplifier The DIVA8G2 Master unit provides enhanced digital audio processing (DSP), a digital message
player, a fully monitored fireman’s microphone, amplifier monitoring with switchover to
Enhanced loudspeaker line surveillance for A/B zoned

backups and loudspeaker line monitoring for 16 audio lines (8 lines A/B). It can process and
installations route one PSS-G2, CD8-G2 or CD16-G2 microphone console or up to ten cascaded PSM8-V3
9 monitored logic control inputs, 8 non-monitored logic
paging microphones, along with two 0dB audio inputs and one mic/line input into two
control inputs different channels (music + voice) using configurable priorities. The DIVA8G2 system utilizes
Ethernet interface for configuration, control, diagnostics
two external amplifier channels with a maximum capacity of 1000 W each.
and logging
PRE-PROCESSING:
Digital storage for up to 45 minutes of pre-recorded

messages in .WAV format All audio inputs feature contact and VOX activation and each input is fitted with volume
controls and equalizers. Up to 45 minutes of digital messaging can be stored in the unit. These
PEQ: 3 bands on inputs, 7 bands on the two outputs

are stored as WAV files and uploaded directly from a PC into the DIVA8MG2. Up to two
channels messages can be played simultaneously in different zones for phased evacuation.
Modbus, notifier, Vox@Net Protocol interface via RS232

Full monitoring of PSS and PSM paging consoles
INTERFACING:
2 channel audio distribution for Paging and BGM

DIVA8MG2 has nine monitored alarm inputs which can be individually programmed for specific
Incident data record with up to 2047 entries
message/input routing to all or selected channels. Each DIVA8G2 system module has eight
Combined back-up amplifier function.
output zones with A/B wiring and each zone can be routed manually or automatically to one

of the system’s audio channels (music or voice). The number of zones can be extended up to
128 A/B zones with the addition of DIVA8SG2 Slave units (up to a maximum of 15 slave units).
1 Fault relays & 1 EVAC relays outputs

The music source can be selected directly from the front panel and switched into each zone
Low and high pass filtering on inputs

separately, also a RS232 port on the rear panel allows third-party control and interfacing.
Programmable of 21 priority levels

2U standard 19” rack mounting

1 Fault & 1 Evac relays outputs


2'' full color TFT screen


8 Logic relay contacts

EN54-16 certified

ATEI
33
DIVA8G2 system
Commercial Audio
Intercommunication
Loudspeakers
DIVA8MG2
REDUNDANCY:
In case of Evacuation, the amplifier music channel can be used as a second alarm channel. Each
DIVA8G2 system requires only one 2-channel amplifier (one channel for music, one for voice).
The music amplifier will also act as a backup amplifier in case of voice amplifier failure. Each
channel can handle up to 1000W audio power (at 100V).
Users shall manually route the Fireman microphone signal, three digital messages into selected
zones, adjust the audio level and switch (ON/OFF) the music in each zones separately from the
front-panel of DIVA8MG2 (Master unit). In case of evacuation, the zone attenuator are auto-
matically bypassed. One output contact per zone can be activated each time the zone is
occupied with a source that has higher priority than the music (alarm or microphone paging).
SECURITY:
In accordance with EN54-16, ISO 7240-16 and BS5839/8, all DIVA8G2 system components and
peripherals are monitored. This monitoring extends from the capsule of a paging station
microphone to the end of a loudspeaker line. The external cables connected to the control
inputs are monitored for short and open circuit and an internally-generated pilot tone is
available for monitoring impedance on the loudspeaker lines. The master unit monitors the
status of all the equipment in the system, reports status changes and stores the last 999 fault
messages in the system. This log can be accessed on the master unit display or on a PC using
the DIVA8G2 control software.
DIVA8G2 system units operate either on 110VAC or 230VAC mains power supply or on a 24V
battery power supply for emergency back-up, with automatic switchover. Both power supplies
are monitored.
INSTALLATION NOTES:
INTERCONNECTIONS:
DIVA8MG2 Master unit and DIVA8SG2 Slave unit

with 4 amplifier channels
ATEI
34
DIVA8G2 system
DIVA8MG2
Front Quantities Components Monitor loudspeaker

2" full color TFT screen
1 DIVA8MG2 Master unit Frequency response -3dB @ 200 Hz and 20 kHz
Zone selection / Music control / EVAC / Reset /
1 Fireman microphone SNR > 70 dB
MSG / Test buttons 1 Power cord (type depends on region) THD < 5% @ 1 kHz @8ohm
Fireman microphone
1 Set of connectors Signal 16 dBu
VACIE indicators
1 Set of 19" rack mount brackets
Zone attenuator knobs
1 DIVA8G2-system software Amplifier Capacity (per channel)
Status indicators (Power / G. Fault / System Fault /
1 LAN Cable Input 1000W
EVAC / Bypass Mode)
Rear Mechanical
Voltage selector
Electrical Dimensions (With 19" rack mount brackets)
Mains power supply (H x W x D) 2RU, 88 x 483 x 338 mm
INTERCONNECTIONS
Voltage 230/115 VAC ±15%, 50/60 Hz (3-1/2" x 19" x 13-3/10")
Front Power consumption 48 W Weight 7.5 kg (16.5lbs)
Fireman microphone
Fuse Rating 1.6 A Mounting 19"-rack mount
Rear Color RAL7016
AC power socket
Voltage 18 - 30 VDC Environmental
9 EVAC inputs
Amp Consumption 1.4 A Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
8 control inputs
2 state inputs(open contact & close contact)
Performance Relative humidity 15% to 90%
8 control outputs
Frequency response -3dB @ 20 Hz and 20 kHz Air pressure 600 to 1100 h Pa
Evac & Fault contacts
1 remote Fireman’s mic input
Audio Line inputs (Optional audio input card)
Music / Line Input
Connector 2x2 RCA (un-balanced)
4 analogue line audio inputs
Frequency response -3dB @ 20 Hz and 20 kHz
Ethernet connection
SNR > 76 dB (Line-level)
8 zone 100 Volt outputs (A+B)
> 78 dB (Mic-level)
RS232 Connector
THD < 0.02% @ 1 kHz
1 monitored paging console input
Input sensitivity 770 mV (0 dBu ~ -60 dBU)
Input impedance 10 kohm
Fireman microphone
Connector 5-pin locking-DIN
Europe Voice Alarm EN54-16 certified 2012 Frequency response -3dB @ 20 Hz and 20 kHz
CE – 0359 SNR > 70 dBu
according to EN50130 – 4 THD < 1% @ 1 kHz @ 8ohm
Signal -40 to -30 dBu
Output impedance 10 kohm
ATEI
35
DIVA8G2 system
Commercial Audio
Intercommunication
Loudspeakers
DIVA8SG2
COMPACT PAVA SYSTEM – SLAVE UNIT – SWITCH MODE
DIVA8G2 system is a compact PAVA solution specifically designed

for small to medium-scale installations. It has all the essential
functionality to comply with EN 54 requirements for Voice Alarm,
including full system monitoring, loudspeaker line impedance
surveillance, microphone surveillance and monitored interfacing
with remote devices.
DIVA8G2 responds to Public Address and Voice Alarm requirements
as stated in EN54-16, ISO 7240-16 and BS5839/8, with specific

The DIVA8SG2 Slave unit is an extension unit for the DIVA8MG2 Master. It increases the number of 2 channel audio distribution for Paging and

paging zones by 8 zones for each slave unit added in the system. Up to 15 slave units can be added BGM combined back-up amplifier function
per DIVA8G2 system and must be used in conjunction with the DIVA8MG2 Master. A complete Ethernet interface for configuration, control,

DIVA8G2 system provides up to 128 zones (A/B). Slave units are linked to the system master via
diagnostics and logging via DIVA8MG2
shielded CAT-5 cable (max. length 100m).
9 monitored logic control inputs, 8 non-

The DIVA8SG2 Slave handles the same 1000 W power capacity as the master unit (at 100V) on each monitored logic control inputs
amplifier channel (music + voice). Each zone can be routed manually or automatically to either channel. 1000 Watts maximum load / 100V line outputs

For maximum flexibility connected amplifiers can distribute their power across multiple slaves or
per channel amplifier
additional amplifier channels can be added to the system to assist where more output power is
Enhanced loudspeaker line surveillance for

needed. The 100 V amplifier signal is simply linked to the slaves to create a 100 V signal bus.
A/B-zoned installations
INTERFACING: 1 Fault relays & 1 EVAC relays outputs

DIVA8SG2 extends the number of input and output contacts available in the system. It includes nine 1U standard 19” rack mounting

alarm inputs triggered either by dry contact or relay (software-selectable), eight logic contact inputs, 8 Logic relay contacts

two external fault contact inputs and eight contact outputs. EN54-16 certified

REDUNDANCY:
In case of Evacuation, the amplifier music channel can be used as a second alarm channel. Each
DIVA8G2 system requires only one 2-channel amplifier (one channel for music, one for voice). The
music amplifier will also act as a backup amplifier in case of voice amplifier failure. Each channel can
handle up to 1000 W audio power (at 100 V).
Users shall manually route the Fireman microphone signal, three digital messages into selected zones,
adjust the audio level and switch (ON/OFF) the music in each zones separately from the front-panel of
DIVA8MG2 (Master unit). In case of evacuation, the zone attenuators are automatically bypassed. One
contact output contact per zone can be activated each time once the zone is occupied with a source
that has higher priority than the music (alarm or microphone paging).
SECURITY:
In accordance with EN54-16, ISO 7240-16 and BS5839/8, all DIVA8G2 system components and
peripherals are monitored. This monitoring extends from the capsule of a paging station microphone to
the end of a loudspeaker line. The external cables connected to the control inputs are monitored for
short and open circuit and an internally-generated pilot tone is available for monitoring impedance on
the loudspeaker lines. The master unit monitors the status of all the equipment for the system, reports
status changes and stores the last 2047 incident in the system. This log can be accessed on the master
unit display or on a PC using the DIVA8G2 control software.
DIVA8G2 system units operate either on 110VAC or 230VAC mains power supply or on a 24V battery
power supply for emergency back-up, with automatic switchover. Both power supplies are monitored.
ATEI
36
DIVA8G2 system
Commercial Audio
Intercommunication
Loudspeakers
DIVA8SG2
INSTALLATION NOTES:
Single amplifier with single back-up Multiple amplifier with single back-up
The DIVA8MG2 Master unit and DIVA8SG2 Slave unit are designed
for entry level solutions. It provides a cost-effective system when
there's only paging requirement or paging with BGM. The DIVA8G2
System concept utilizes switched audio distribution from a single
amplifier source to up to 128 loudspeaker groups. DIVA8MG2 Master
unit and DIVA8SG2 Slave unit have 4 different system solutions.
1. Block-diagram (the upper one)
Require only 2 amplifiers DIVA8MG2 Master unit and DIVA8SG2 Slave

unit in SINGLE CHANNEL mode shows how DIVA8MG2 Master unit
and DIVA8SG2 Slave unit are connected to the amplifiers and to the
loudspeaker lines using multiple slaves.
LEFT: SINGLE-audio for Paging/Alert and Backup for small loads.

Each channel can handle up 1000 W audio power a 100 V and be
supplied not only for the master unit but also the slave units in each
zone. Note: The backup amplifier must have the same power
capacity as the Paging/Alert amplifier.
RIGHT: SINGLE-audio for Paging/Alert and Backup for higher

loads. Requires and processes 0 dB audio outputs and handle up
3000 W audio power at 100 V from the DIVA8M Master unit to the
DIVA8S slave units, feeding into the additional amplifiers. The system
needs 1 Back-up amplifier to run the multiple DIVA master and slave 1000 Watt System 3 x 1000 Watt System
units. Note: The Backup amplifier must have the same power
capacity as the Paging/Alert amplifier in the system.
Single amplifier set Multiple amplifier sets
2. Block-diagram (the lower one)
DIVA8MG2 Master unit and DIVA8SG2 Slave unit in DUAL CHANNEL

mode shows how DIVA8MG2 Master unit and DIVA8SG2 Slave unit
are connected to the amplifiers and to the loudspeaker.
LEFT: DUAL-audio for Paging/Alert/BGM and Backup for small

loads. Each channel can handle up 1000 W audio power at 100 V
and be supplied not only for the master unit but also the slave units
in each zone. Note: The BGM/Backup amplifier must have the same
power capacity as the Paging/Alert amplifier in case of amplifier
failure.
RIGHT: DUAL-audio for Paging/Alert/BGM and Backup for higher

loads. Requires and processes 0 dB audio outputs and handle up
3000 W audio power at 100 V from the DIVA8M Master unit to the
DIVA8S slave units, feeding into the additional amplifiers. In this
configuration, amplifiers provide paging and music in individual
zones simultaneously. Note: The BGM/Backup amplifier must have
the same power capacity as the Paging/Alert amplifier in the system.
1000 Watt System 3 x 1000 Watt System
ATEI
37
DIVA8G2 system
DIVA8SG2
Front Quantities Components Amplifier Capacity (per channel)

Zone selection buttons
1 DIVA8SG2 Slave unit Input 1000W
Zone status / Power indicators
1 Power cord (type depends on region)
VACIE indicators (EVAC / Fault / Alert / Page /
1 Set of connectors Mechanical
Selected) 1 Set of 19” mounting brackets Dimensions (With 19" rack mount brackets)
(H x W x D) 1RU, 44 x 483 x 277 mm
(1-3/4" x 19" x 10-9/10")
Rear Electrical Weight 3.9 kg (8.6 lbs)
AC power socket
Mains power supply Mounting 19"-rack mount
Voltage 230/115 VAC ±15%, 50/60 Hz Color RAL7016
9 EVAC inputs
Power consumption 35 W
8 control inputs
Fuse Rating 1.6 A Environmental
2 state inputs(open contact & close contact)
Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Master to Slave link
Battery power supply Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
8 zone 100 Volt outputs (A+B)
Voltage 18 - 30 VDC Relative humidity 15% to 90%
Terminator switch
Amp Consumption 1.4 A Air pressure 600 to 1100 h Pa
Heat Dissipation 120 BUT/hr
Performance
Frequency response -3 dB @ 20 Hz and 20 kHz

CE – 0359
according to EN50130 – 4
ATEI
38
Commercial Audio
Intercommunication
DPAfour
Loudspeakers
Digital Power Amplifiers
DPAfour (Digital Power Amplifier),

SPA (Security Power Amplifier) and
BPA (Bridging Power Amplifier) are
designed for public address or
voice alarm system application.
They were specifically developed
to meet the requirements of EN54-
16 and can therefore also be used
as part of fire detection and fire
alarm systems.
Commercial Audio
Intercommunication
Loudspeakers
SONAES
Charger and Monitoring Unit
BPA
Bridging Power Amplifiers
SPA
Security Power Amplifiers
ATEI
Amplifiers
Commercial Audio
Intercommunication
Loudspeakers
DPAfour
DIGITAL POWER AMPLIFIERS
MAIN CHARACTERISTICS The DPAfour is a 2RU 19" rack mountable, 4-channel class-D power amplifier, transformer
4 audio outputs (100 V /70 V /50 V / 4 Ohm

isolated for 100 V, 70 V, 50 V and 4 Ohm distributed loudspeaker systems. There are two
selectable) models in the DPAfour range:
DPAfour 125 rated at 4 x 125 W
Fault reporting outputs

DPAfour 250 rated at 4 x 250 W
Four audio input gain control

And one model in 8-channel range:
Advanced audio processing for each amplifier

DPA8060 rated at 8 x 60 W
channel using DIVA8G2 or IDA8 systems
Each channel can deliver up to 125/250W as a separate channel or can be bridged to deliver
Supervision of the amplifiers through DIVA8G2

higher power. The amplifier has a dual-voltage mains supply 115/230V AC (selectable internally)
or IDA8 systems
and a 24 VDC battery back-up connection.
Back up amplifier switching through DIVA8G2

or IDA8 systems In combination with DIVA8G2 and IDA8 the DPAfour amplifiers have the following features:
Loudspeaker line monitoring with DIVA8G2 or

Loudspeaker line monitoring for Shortcut Open line Ground leakage.
IDA8
Output bridging for higher power
Single spur A/B loudspeaker lines individually monitored By adding a SONAES to the system a
fully EN54-16 certified Voice Alarm system will be created, with extensive PA capabilities.
DIVA8G2 & DPA Wiring example

with DPA Ch 1&2 bridged
*If DPA channels are bridged,

gain settings should be
set at equal level for both
channel 1&2 and/ or 3&4
IDA8 & DPA

Wiring example
ATEI
41
Amplifiers
DPAfour
DIGITAL POWER AMPLIFIERS
CONTROLS AND INDICATORS TECHNICAL SPECIFICATIONS
LED VU metering
Electrical Loudspeakers outputs DPA4250
Status indicators for: Signal, Clip, Mains, Battery,
Mains power supply Rated load resistance 40 ohm (100 V)
Channel fault and General fault Voltage 230/115 VAC ±15%, 50/60 Hz Rated load capacitance 120 nF (100 V)
Power consumption** standby - idle* - Pmax (per CH.) Rated output power 250 W (cont. at 40°C)
INTERCONNECTIONS
DPA8060 5 W – 10 W – 85 W (per channel)
Rear DPA4125 1 W – 38 W – 180 W Two channels bridged 500 W (cont. at 40°C)
Rotary volume control
DPA4250 1 W – 44 W – 360 W
Mains switch
**(Total Mains-power consumption @ 230 VAC) Frequency response 40 Hz to 20 kHz(-3 dB)
AC power socket
*(Alarm cycle + 10 V pilot-tone @ 24 VDC) SNR >90 dB (no pilot tone)
Crosstalk <70 dB at nominal load for 1 kHz
Four line inputs
Battery power supply Distortion <0.1% (@ 1 kHz)
100 V, 70 V, 50 V or 4 ohm outputs
Voltage 19-30 VDC @ -10dB of rated output power
(for each amplifier channel) Power consumption** standby - idle* - Imax (per CH.)
DPA8060 0.2 A – 0.4 A – 2.6 A Mechanical
DPA4125 0.03 A – 1.45 A – 5.6 A Dimensions (19" with the fixing holes included)
DPA4250 0.03 A – 1.65 A – 11 A (H x W x D) 2RU, 88.5 x 483 x 370 mm
**(Total Mains-power consumption @ 230 VAC) (3-1/2" x 19" x 14-3/5")
Europe Voice Alarm EN54-16 certified 2012 *(Alarm cycle + 10 V pilot-tone @ 24 VDC) Weight
CE – 0359 DPA8060 12.7 kg (27.9 lbs)
according to EN50130 – 4 Performance DPA4125 14 kg (31 lbs)
Line inputs 4 x (One per channel) DPA4250 18 kg (40 lbs)
PARTS INCLUDED
8 x for DPA8060 Mounting 19"-rack mount
Quantities Components Connector 3-pin phoenix Color RAL7016
1 DPA xxxx Digital Power Amplifier Frequency response +/-3 dB @ 50 Hz and 20 kHz
1 Power cord SNR > 90 dB Environmental
1 Set of connectors THD < 0.1% @ 1 kHz Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Input sensitivity 770 mV Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Input impedance 22k Ohm Relative humidity 15% to 90%
Loudspeakers outputs DPA8060 Heat Dissipation
Rated load resistance 167 Ohm (100 V); 82 Ohm (70 V) DPA8060 685 BTU/hr
Rated load capacitance 30 nF (100 V); 60 nF (70 V) DPA4125 750 BTU/hr
Rated output power 60 W (1 min. at 40°C) (per CH) DPA4250 1500 BTU/hr
Loudspeakers outputs DPA4125

Rated load resistance 80 ohm (100 V)
Rated load capacitance 62.5 nF (100 V)
Rated output power 125 W (cont. at 40°C)
(per channel)
Two channels bridged 250 W (cont. at 40°C)
ATEI
42
Amplifiers
Commercial Audio
Intercommunication
Loudspeakers
SPA
SECURITY POWER AMPLIFIERS
MAIN CHARACTERISTICS There are two types of power amplifier units in the SPA-PAVA product range. The overall
2 audio outputs (selectable 100 / 70 / 8 Ohm

power rating is 2x120 or 2x240 watts. The power amplifiers can be set to 100 V, 70 V and 8
outputs) Ohm output tapings. They have short-to-ground, short-circuit detection and line-impedance
surveillance up to 5% deviation using the DIVA8G2 and IDA8 range of products for

loudspeaker-line surveillance.
Two audio inputs with gain-set

Supervision of the amplifiers using DIVA8G2 or

They support both single-spure and redundant loop cabling (A/B). The amplifiers have a
IDA8 controllers changeover facility for spare power amplifier switching. Both features are facilitated by the
DIVA8G2 and IDA8 controllers and slaves. The amplifiers have a 24 VDC back-up supply input.

channel using DIVA8G2 or IDA8 systems FUNCTIONS:
Amplifier supervision and spare amplifier

The power amplifiers receive line-level input signals from the DIVA8G2 and IDA8 controllers and
switching through DIVA8G2 or IDA8 systems
slaves. The display panel will show the VU-meter is reading data when the EN54-16 default switch
Loudspeaker line and loudspeaker supervision
is inhibited.
through DIVA8G2 or IDA8 systems
DIVA8G2 & SPA

Wiring example
IDA8 & SPA

Wiring example
ATEI
43
Amplifiers
SPA
SECURITY POWER AMPLIFIERS
LED VU metering
Electrical Loudspeakers outputs SPA2240
Status indicators for: Overload, Over temperature,
Mains power supply Rated load resistance 40 Ohm (100 V); 20 Ohm (70 V)
Battery and Mains Voltage 220 VAC ±10%, 50 Hz Rated load capacitance 125 nF (100 V); 250 nF (70 V)
Power consumption** idle* - Pmax (per CH.) Rated output power 240 W (cont. at 40°C)
INTERCONNECTIONS
SPA2120 12 W – 290 W (per channel)
Rear SPA2240 12 W – 550 W
**(Total Mains-power consumption) Frequency response 20 Hz to 20 kHz @ -3 dB
Mains switch
*Idle: Measured with 10 Volt surveillance SNR > 90 dB (no pilot tone)
AC power socket
tone on the output. Crosstalk < 80 dB at nominal load for 1 kHz
Fuse Rating Distortion < 1% (@ 1 kHz) @ -10dB
Four line inputs
SPA2120 5 A@110 V, 2.5 A@250 V of rated output
100 V, 70 V or 8 ohm outputs
SPA2240 8 A@110 V, 5 A@250 V
(for each amplifier channel) Mechanical
Battery power supply Dimensions (For 19" rack use with brackets)
Voltage 19-30 VDC (H x W x D)
Power consumption** idle* - Imax (per CH.) SPA2120 2RU, 88 x 425 x 305 mm
SPA2120 0.4 A – 8 A (3-1/2" x 16-3/4" x 12")
Europe Voice Alarm EN54-16 certified 2012 SPA2240 0.4 A – 15 A SPA2240 2RU, 88 x 425 x 402 mm
CE – 0359 **(Per ch. @ 24 VDC) (3-1/2" x 16-3/4" x 15-4/5")
according to EN50130 – 4 *(Alarm cycle + 10 V pilot-tone @ 48 VDC) Weight
SPA2120 12.3 kg (27.1 lbs)
PARTS INCLUDED
Performance SPA2240 18.5 kg (40.8 lbs)
Quantities Components Line inputs 2 x (One per channel) Mounting 19"-rack mount
1 SPA 2xxx Security Power Amplifier Connector 3-pin XLR and 3-pin phoenix Color RAL7016
1 Power cord (electronically balanced)
1 Set of mounting brackets for 19" rack Frequency response +/-3 dB @ 40 Hz and 20 kHz Environmental
1 Set of connectors SNR > 86 dB @ 1k Hz at full power Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
1 Set of feet THD <=1% @ 1k Hz Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Input range -6 dBV to 6 dBV / 770mV Relative humidity 15% to 90%
Input impedance 22k Ohm Air pressure 600 to 1100 h Pa
Heat Dissipation
Loudspeakers outputs SPA2120 SPA2120 1160 BTU/hr
Rated load resistance 83 Ohm (100 V); 41 Ohm (70 V) SPA2240 2110 BTU/hr
Rated load capacitance 60 nF (100 V); 125 nF (70 V)
Rated output power 120 W (cont. at 40°C)
(per channel)
ATEI
44
Amplifiers
Commercial Audio
Intercommunication
Loudspeakers
BPA
BRIDGING POWER AMPLIFIERS
MAIN CHARACTERISTICS The BPA is a 2RU 19" rack-mountable, 2-channel amplifier, transformer isolated for 100 V, 50 V
2 audio outputs for BPA2120, 2240 and 2480

and 8 Ohm distributed loudspeaker systems. There are three models in the coverage of BPA:
(100 V / 50 V / 8 ohm selectable outputs) BPA2120: 2 x 120 W
BPA2240: 2 x 240 W

BPA2480: 2 x 480 W
Two audio inputs with gain-set

The BPA amplifier has a 230 VAC mains supply input and a 48 VDC battery back-up input which
Supervision of amplifiers through DIVA8G2 or

allows it to be used in combination with a battery backup system for maximum availability and
IDA8 systems
reliability in an emergency evacuation system. BPA amplifiers have short-to-ground, short-circuit

detection and line-impedance surveillance up to 5% deviation using the DIVA8G2 or IDA8 systems
channel through DIVA8G2 or IDA8 systems for loudspeaker-line surveillance. They support both single-spure and redundant loop cabling (A/B)
Amplifier supervision and spare amplifier
and have a switchover facility that automatically reroutes power to a backup amplifier (if present).
switching through DIVA8G2 and IDA8 systems BPA amplifiers have a rear-panel selector switch for amplifier monitoring according to EN 54-16.
Loudspeaker line and loudspeaker supervision

through DIVA8G2 and IDA8 systems
DIVA8G2 & BPA

Wiring example
IDA8 & BPA

Wiring example
ATEI
45
Amplifiers
BPA
BRIDGING POWER AMPLIFIERS
LED VU metering
Electrical Loudspeakers outputs BPA2240
Status indicators for: Overload, Over temperature,
Mains power supply Rated load resistance 40 ohm (100 V); 10 ohm (50 V)
Battery and Mains Voltage 230 VAC ±10%, 50/60 Hz Rated load capacitance 125 nF (100 V); 500 nF (50 V)
Power consumption** standby - idle* - Pmax (per CH.) Rated output power 240 W (1 min. at 40°C) (per CH)
INTERCONNECTIONS
BPA2120 5 W – 11 W – 295 W
Rear BPA2240 5 W – 11 W – 550 W Loudspeakers outputs BPA2480
BPA2480 5 W – 13 W – 1000 W Rated load resistance 20 ohm (100 V); 5 ohm (50 V)
Mains switch at the rear of the device
**(Total Mains-power consumption) Rated load capacitance 250 nF (100 V); 1 uF (50 V)
AC power socket
*Idle: Measured with 10 Volt surveillance Rated output power 480 W (1 min. at 40°C) (per CH)
tone on the output.
Two line inputs
Fuse Rating Frequency response 20 Hz to 20 kHz @ -3 dB
100 V, 50 V or 8 ohm outputs
BPA2120 5 A@110 V, 2.5 A@250 V SNR > 90 dB (no pilot tone)
(for each amplifier channel) BPA2240 8 A@110 V, 5 A@250 V Crosstalk < 80 dB at nominal load for 1 kHz
BPA2480 16 A@110 V, 7 A@250 V Distortion < 1% (@ 1 kHz) @ -10dB
of rated output
Europe Voice Alarm EN54-16 certified 2012 Battery power supply
CE – 0359 Voltage Mechanical
according to EN50130 – 4 BPA ALL TYPES 48-53 VDC Dimensions (For 19" rack use with brackets)
Power consumption** standby - idle* - Imax (per CH.) (H x W x D)
PARTS INCLUDED
BPA2120 0.09 A – 0.16 A – 4.07 A BPA2120 / BPA2240 2RU, 88 x 430 x 375 mm
Quantities Components BPA2240 0.09 A – 0.23 A – 8.13 A (3-1/2" x 17" x 14-3/4")
1 BPA 2xxx Bridging Power Amplifier BPA2480 0.09 A – 0.23 A – 13 A BPA2480 2RU, 88 x 430 x 430 mm
1 Power cord **(Per ch. @ 48 VDC ) (3-1/2" x 17" x 17")
1 Set of mounting brackets for 19" rack *(Alarm cycle + 10 V pilot-tones @ 48 VDC) Weight
1 Set of connectors BPA2120 13.7 kg (30.2 lbs)
1 Set of feet Performance BPA2240 16.2 kg (35.7 lbs)
Line inputs 2 x (One per channel) BPA2480 20.5 kg (45.1 lbs)
Connector 3-pin XLR and 3-pin phoenix Mounting 19"-rack mount
(electronically balanced) Color RAL7016
Frequency response +/-3 dB @ 50 Hz and 18 kHz
SNR > 90 dB @ 1K Hz at full power Environmental
THD < =1% @ 1 kHz Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Input range -6 dBV to 6 dBV / 770mV Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Input impedance 22k Ohm Relative humidity 15% to 90%
Loudspeakers outputs BPA2120 Heat Dissipation
Rated load resistance 83 Ohm (100 V); 20 Ohm (50 V) BPA2120 1160 BTU/hr
Rated load capacitance 60 nF (100 V); 250 nF (50 V) BPA2240 2110 BTU/hr
Rated output power 120 W (1 min. at 40°C) (per CH) BPA2480 3550 BTU/hr
ATEI
46
Battery Charger
Commercial Audio
Intercommunication
Loudspeakers
SONAES
CHARGER AND MONITORING UNIT - EN 54-4
MAIN CHARACTERISTICS CHARGER AND MONITORING UNIT - EN 54-4

Soneas 6/40
The SONEAS series of battery chargers (24 VDC) are designed for Voice Alarm System. The
battery chargers are microprocessor based devices that have been designed to charge lead
2RU-rackmount charger

acid batteries (back-up batteries connected to the Voice Alarm System) and, simultaneously, to
3 Auxiliary outputs, max. 5 A per output

provide power to auxiliary devices such as the DIVA8G2 and IDA8 system controllers.
2 Main outputs, max. 20 A per output

The SONEAS battery chargers, 6/40 and 12/150, are EN54-4 certified. The maximum charging
Battery capacity: 24 AH to 114 AH

current is 6 or 12 A. The battery charger is two rack units high, and has to be installed in a 19"
Soneas 12/150 rack. Maximum battery capacity 114 or 225 AH. The SONAES comes without batteries.
2RU-rackmount charger

OVERVIEW:
3 Auxiliary outputs, max. 5 A per output

6 Main outputs, max. 40 A per output

To meet the secured power back-up system need, determining the exact conditions and the
amount of battery back-up for a system is much complex than other applications. Public Address /
Battery capacity: 65 AH to 225 AH

Voice Alarm system does not draw a constant current. The standard defines a standby time and an
evacuation time. In this case, it is crucial to pick a battery back-up
that shall supply the minimum amount of power for a set amount
of time. With SONAES battery chargers, it provides you with a
battery calculator program which determines the exact capacity.
REGULAR PROCEDURE AS FOLLOWS:
1. Determine the standby / evacuation current and the amount of

battery back-up of the system.
2. Detect and enhance the standby / evacuation current

simultaneously for 24 hours.
3. 24 Hours discharge capacity of the battery.
INSTALLATION NOTES FOR SONAES 6/40
ATEI
47
Battery Charger
SONAES
CHARGER AND MONITORING UNIT - EN 54-4
Europe Voice Alarm EN54-4 Mechanical

0333 – CPD – 075381 Dimensions (With 19" rack mount brackets)
0333 – CPD – 075382 (H x W x D) 1RU, 44 x 483 x 310 mm
(1-3/4" x 19' x 12")
PARTS INCLUDED
Weight
Quantities Components SONEAS 6/40 4.9 kg (10.8 lbs)
1 SONEAS 6/40A or SONEAS 12/150A SONEAS 12/150 6 kg (13 lbs)
1 Set of connectors Mounting 19"-rack mount
Color RAL7016
Electrical Environmental
Mains power supply Operating temperature -5ºC ~ 45ºC (23ºF ~ 113ºF)
Voltage 230 VAC ±15%, 50/60 Hz Storage temperature -20ºC ~ 85ºC (-4ºF ~ 185ºF)
Power consumption 380 W at Full load Relative humidity 20% to 95% (Non-Condensing)
Battery power supply Heat Dissipation 1300BTU/hr
Voltage 24 VDC
Maximum charging current
SONEAS 6/40 6A
SONEAS 12/150 12 A
Outputs
Main for amplifiers
SONEAS 6/40 max. 40 A for 5 outputs
SONEAS 12/150 max. 150 A for 9 outputs
Auxiliary for controllers 3 x
Maximum current 5A
Soneas 6/40
Batteries 2x12 V, 24 to 225AH

Brands Yuasa NPL Series
Power-Sonic GB Series
ABT TM Series
EnerSys VE Series Soneas 12/150
Effekta BTL Series
Long GB Series
ATEI
48
Commercial Audio
Intercommunication
Loudspeakers PSS AS /
PSS G2 /
PSS G2E
Color Touch-Screen Secured

Paging Console
PSS AS / PSS G2 : paging console, CD-

touch : wall-mounted monitored touch -
screen paging console, CD8 / CD16 :
Wall-mounted Monitored Paging Console,
PPM / PSM : Desktop Paging Consoles
for Commercial Use, DialPad / Wireless
Transceiver : Touch Dial device for IDA8
system, RAC5 / RAC8 : Wall-mounted
PPM-IT5 PPM / PSM
Level Sources Remote Selector, URC -
Color Touch-Screen Secured Desktop Paging Consoles
Programmable Remote Controller with
IP Paging Console
Display, DNM - Digital Noise Sensing
Microphone, URGP - Alarm Input Interface
for IDA8 System and DIVA8 System,
respond to Public Address and Voice
Alarm requirements with specific attri-
butes for compliance in small, medium
and large installations.
Commercial Audio
Intercommunication
Loudspeakers
CD-touch
URC Wall-mounted Monitored

Touch -screen Paging Console
Programmable Remote
Controller with Display
URGP
Alarm Input Interface for

IDA8-System and DIVA-System
CD 8 / CD16
Wall-mounted Monitored
Paging Console
Commercial Audio
Intercommunication
Loudspeakers
PSS AS / PSS G2 / PSS G2E / PPM-IT5

FULL COLOR TOUCH-SCREEN SECURE PAGING CONSOLE
The PSS paging console comes with a 5" TFT touch screen interface which allows call-paging,
message broadcasting and DSP matrix parameter control over a secure (monitored) bus. The
backlit full-color touch screen is designed for simple, user-friendly operation and offers a total
of 168 software keys across 14 pages for zone or group of zones selections. Each key
contains a color-changing field indicating that the zone is occupied by a different process.
Alongside the touch screen, three hardware keys are also provided for free assignment within
the software.
Several levels of operation with password protection make the PSS a versatile device that fits as
well in a commercial shopping center as in an industrial high-security environment. All paging
parameters for site operation can be pre-programmed; zones can be assigned, named, grouped to
different buttons, message triggered and level, pre-call chime set and adjusted. The message and
the chime can also be stored in the PSS console. In addition, fader control, button control and
PSS MAIN CHARACTERISTICS event control can also be pre-configured.
Secured CAT-5 link to controllers and slaves

The PSS AS and the PSS G2 are powered by 24V DC supply.
Supervision of microphone capsule

Note: There are two versions of the PSS paging console with identical hardware and functionality
Monitoring loudspeaker
but different firmware for compatibility with different systems.
5” full color touch-screen, 800 x 480 pixels

PSS AS: Used with IDA8 system and ECS system controllers and slaves
14-pages x 12 keys

Power, status and fault indicator

PSS G2: Used with DIVA8G2 system controllers
Comprehensive system status information from

PSS G2E: Used with DIVA8G2 system controllers and can be powered by Ethernet.
touch-screen
EN54-16 certified

The ATEÏS range of security systems complies with current architectural demands requiring IP
and/or fiber-optic networking to cater for any possible PAVA design, however complex. ATEÏS
responds to Public Address and Voice Alarm requirements as stated in EN54-16, ISO 7240-16 and
BS5839/8, with specific attributes for compliance in large installations.
PPM-IT5 MAIN CHARACTERISTICS

5" TFT full color paging console

High quality gooseneck microphone and built-

in loudspeaker
Ethernet interface including PoE (Power Over

Ethernet)
Automatic gain control on microphone input

Echo cancellation / Noise Reduction

Up to 300 pages x 12 keys

G.711 / G.722 / G.726 / G.727 audio encoding

/decoding
Audio Stream using SHOUTcas t / ICEcast (AAC
PPM-IT5: The 3 hardware keys can be freely assigned by software. The PPM-IT5 Media console is a
48K/44.1K) protocols versatile device that enhances paging over IP-networking.
Half or full duplex conversation

All paging parameters needed for site operating can be programmed: zones assigned to different
Memory space for prerecorded messages and
buttons, name of zones, group of zones, messages triggering or event control. A total of 3600 keys
chime over 300 pages allow zones or groups of selection. All the settings shall be done via web pages
3 key-buttons: User-definable via ATEÏS Studio
with your web browser.
GUI
RJ 9 for telephone headset and 2 mini-jack

plugs for headset (optional)
ATEI
51
PSS AS / PSS G2 / PSS G2E / PPM-IT5

FULL COLOR TOUCH-SCREEN SECURE PAGING CONSOLE
5" full color touch-screen, 800x480 pixels

Electrical Mechanical
Three LED status indicators
Mains power supply Dimensions(H x W x D) 80 x 250 x 140 mm
Three hardware function keys-buttons
Voltage 18~30 VDC PoE: 24 VDC) (3-1/5" x 9-4/5" x 5-1/2")
280 mm gooseneck microphone
Power consumption 250 mA Weight 1.1 kg (2.4 lbs)
Color RAL7016
INTERCONNECTIONS
Performance
Rear Frequency response Environmental
RJ45
for CAT-5 connection PSS AS/G2/G2E -3 dB @ 200 Hz to 8 kHz Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
3.5mm
mini-jack for headset PPM-IT5 -3 dB @ 100 Hz to 18 kHz Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Additional
power supply connector for long-line THD < 1% @ 1 kHz Relative humidity 15% to 90%
support Output level Max 6 dBu Air pressure 600 to 1100 h Pa
Noise gate threshold -84 dBu ~ – 24 dBu Heat Dissipation 20 BTU/hr
Attack time 8 ms
Release time 100 ms
Output impedance 100 Ohm
CE – 0359 Monitoring speaker
according to EN50130 – 4 Impedance 4 Ohm
Output power 1 W @ 1 Khz
PARTS INCLUDED
Frequency response -3 dB @ 200 to 12 kHz
Quantities Components
PSS AS/G2/G2E Headset
1 PSS-XX Connector
1 CAT-5 cable, 1.5 m PSS AS/G2/G2E 3.5 mm mini-jack
PPM-IT5 PPM-IT5 2 x 3.5 mini-jack
1 PPM-IT5XX
1 CAT-5 cable, 1.5 m System Connection
1 AC-DC power adapter Cable type CAT-5 (FTP)
Length 100 m
ATEI
52
Commercial Audio
Intercommunication
Loudspeakers
PPM AS / PSM
DESKTOP PAGING CONSOLES
PPM is a unidirectional addressable condenser

paging microphone compatible with IDA8 and
DIVA8 systems. PPM uses RS485 protocol over
a single CAT-5 cable connection to transport
both audio and power from the paging console
to the system units. The PPM has 8 zone
buttons with a sleek gooseneck microphone,
providing both durability and aesthetics in a
slim, stable chassis.
Desktop enclosure

Monitored CAT-5 link to controllers and slaves

PPM is a unidirectional addressable condenser paging microphone compatible for IDA8 and DIVA8
Supervision of microphone capsule (not on

systems. In accordance with BS5839, PPM is monitored by using RS485 protocol over a single CAT-
slave units)
5 cable connection to transport both audio and power from the paging console to the system
Automatic gain control on microphone input
units. The PPM has 8 zone buttons with a sleek gooseneck microphone, providing both durability
8-zone selection keys (Expandable with
and aesthetics in a slim, stable chassis.
additional keypads)
The PPM enables live announcement to any pre-assigned zones (an optional SP version also allows
All-call key

for broadcasting the pre-recorded messages). The paging station has a gooseneck microphone, a
Power indicator
push-to-talk button, zone selection keys and a monitor speaker. Buttons represent a single zone or
EVAC indicator
a group of zones and be easily defined in the software using a simple matrix selection. All buttons
Status and fault indicator

can be programmed with drag & drop features from the software and each button can be
programmed for PTT (Push To Talk) or latching functionality.
Monitor speaker

In addition to the zone LEDs, “Hold” and “Busy” LED signals make PPM an extremely user-friendly
paging console. Thanks to the cardioids polar pick-up pattern, the unidirectional condenser
microphone ensures the high-quality and directive signal pick-up with minimal interference from
the surroundings.
The RS485 communication protocol allows daisy-chain wiring up to 300m on a single CAT-5 cable
(FTP/STP) and makes each station easy to connect by using standard RJ45 connectors and the
junction connection box (supplied with PPM). Also, the console can be powered locally with 24V
DC supply.
Note: There are three versions of the PPM paging console with identical hardware and
functionality but different firmware for compatibility with different systems.
PPM-AS: Used with IDA8 system controllers and slaves, ATEÏS Audio Processor, LAPG2T and UAPG2
PPM AS with keypads
PSM: Used with DIVA8 system controllers
PPM-SP, PPM G2: Used with ATEÏS Audio Processor, LAPG2T and UAPG2
ATEI
53
PPM AS / PSM

Activity indicators
Battery power supply Dimensions(H x W x D) 50 x 105 x 190 mm
Voltage 18 - 26 VDC (2" x 4-1/5" x 7-1/2")
Gooseneck microphone
Power consumption 120 mA (With gooseneck) 350 x 105 x 190 mm
Monitor speaker
(13-3/4" x 4-1/5" x 7-1/2")
Performance Weight 0.7 kg (1.54 lbs)
INTERCONNECTIONS
Frequency response -3 dB @ 200 to 8kHz Color RAL7035
Rear THD < 0.1% @ 1 kHz
RJ45
for CAT-5 connection Output level Max 6 dBu Environmental
Noise gate threshold -84 dBu ~ -24 dBu Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
PARTS INCLUDED
Attack time 8 ms Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Quantities Components Release time 100 ms Relative humidity 15% to 90%
1 PPM/PSM-XX Output impedance 100 Ohms Air pressure 600 to 1100 h Pa
1 Junction box IP rating 30
1 CAT-5 cable, 10pin, 1.5 m Monitoring speaker Heat Dissipation 10 BTU/hr
Impedance 4 Ohm
Frequency response 3 dB @ 200 to 12 kHz
System Connection
Cable type CAT-5, 10 pin (FTP)
Length 100 m
ATEI
54
Commercial Audio
Intercommunication
Loudspeakers
PSC
The PSC microphone console, an Unidirectional Condenser Addressable Microphone

which is compatible with all system units. By using RS485 protocol with daisy-chain
wiring can support up to 100M over a single CAT5 cable connection, PSC transmits
both audio data and power supply to system units. PSC comprises of 8 zones / 8
buttons with sleek condenser gooseneck microphone, and spring metal protection,
providing durability and excellent aesthetics as well as enhancing up to 256 zones
expansion via the additional keypad. The control buttons represent a single zone or a
group of zones and are easily defined via the GUI of the system units using a simple
Matrix selection.
Besides the original speaker, PSC also supports an external speaker to monitor the
audio source. The unit offers “Hold” and “Busy” LED signals in addition to the zone
LED’s, and these features allow an easy identification of Selection / Busy signals for
users.
All buttons can be programmed with drag & drop features from the System unit GUI
software and each button can be programmed for Push To Talk function or Latch
functionality. The unidirectional condenser microphone warrants picking up the high
quality of directive signal and less interference from the surroundings.
SPECFICATIONS
Goose-neck Microphone
Electrical Monitoring speaker
Fault / EVAC / Power / Talk / Hold / All Call /
Mains power supply Impedance 8 Ohm
Release / Busy Indicator Voltage 18~30 VDC PoE: 44~57 VDC) Output power 1 W @ 1 Khz
All Call/Release/Talk Button
Power consumption 150 mA Frequency response -3 dB @ 200 to 20 kHz
Microphone Connector

Event Select Key

Performance Mechanical
Frequency response -3 dB @ 200 Hz to 20 kHz Dimensions(H x W x D) 116 x 220 x 483 mm
INTERCONNECTIONS
THD < 1% @ 1 kHz (4-3/5" x 8-3/5" x 19")
Rear Output level Max 6 dBu Weight 0.37 kg (0.8 lbs)
RS485 for CAT-5 connection

Noise gate threshold -84 dBu ~ – 24 dBu Color RAL7035
Release time 100 ms
PARTS INCLUDED
Output impedance 100 Ohm Environmental
Quantities Components Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
1 PSC-XX System connection Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
1 Junction Box Cable type / Length CAT-5,10 pin (FTP) / 100 m (max.) Relative humidity 15% to 90%
1 CAT-5 cable, 10pin, 1.5 m Air pressure 600 to 1100 h Pa
IP Rating 30
ATEI
55
Commercial Audio
Intercommunication
Loudspeakers
CD-Touch
WALL-MOUNTED MONITORED TOUCH-SCREEN PAGING CONSOLE
The CD-TOUCH paging console is a paging interface that allows call-paging, message
broadcasting and DSP matrix parameter control. It contains a 5” full-color backlit touch-screen
for simple, user-friendly operation. The screen offers up to 168 buttons across 14 pages which
can be freely assigned in the software to any zone or group of zones. Each key contains a
color-changing field indicating if the zone is occupied by a different process. In addition, the CD-
TOUCH has 3 hardware keys that can be assigned within the system control software.
All paging parameters for site operation can be pre-programmed and stored within the console,
including message triggering, level adjustment and pre-call chime setup. Zone assignment, naming
MAIN CHARACTERISTICS and grouping can also be pre-configured.
Wall-mounted metal enclosure with lockable

The CD-Touch-XX units connect to a monitored bus on CAT-5 FTP/STP. This connection also provides
cover Power Over Ethernet (POE). In case POE is not available, or if the cable run is greater than 100m, an
additional power connection is provided with 24 VDC supply.
Monitoring of microphone capsule
The ATEÏS range of security systems complies with current architectural demands requiring IP and/or
Monitoring loudspeaker
fiber-optic networking to allow for even the most complex of system designs. ATEÏS responds to
5” full colour touch-screen, 800x480 pixels
Public Address and Voice Alarm requirements as stated in EN54-16, ISO 7240-16 and BS5839/8, with
specific attributes for compliance in large installations.
14 pages of 12 buttons

Power, Fault and Evac indicators

CD-TOUCH is available in two different versions with identical hardware and functionality but different
Comprehensive system status information from
firmware for compatibility with different systems.
touch-screen
CD-TOUCH-AS: For use with IDA8 and ECS system controllers and slaves
EN54-16 certified

CD-TOUCH-G2: For use with DIVA8 system controllers
SPECFICATIONS
5" full color touch-screen, 800x480 pixels

Electrical System connection
Mains power supply Cable type / Length CAT-5 (FTP) / 100 m (max.)
Three hardware function keys-buttons
Voltage 18~26 VDC
Fireman's fist microphone with PTT switch
Power consumption 250 mA Mechanical
Dimensions(H x W x D) 397 x 206 x 127 mm
INTERCONNECTIONS
Performance (15-3/5" x 8-1/10" x 5")
Rear Frequency response -3 dB @ 200 Hz to 8 kHz Weight 4.4 kg (9.7 lbs)
RJ45
for CAT-5 connection THD < 1% @ 1 kHz Color RAL7016
Additional
power supply connector Output level Max 6 dBu
(for 24 V DC external supply in PoE not available) Noise gate threshold -84 dBu ~ – 24 dBu Environmental
Attack time 8 ms Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
PARTS INCLUDED
Release time 100 ms Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Quantities Components Output impedance 100 Ohm Relative humidity 15% to 90%
1 CD-Touch-XX Air pressure 600 to 1100 h Pa
1 CAT-5 cable, 1m Monitoring speaker Heat Dissipation 20 BTU/hr
Impedance 4 Ohm
ATEI
56
Commercial Audio
Intercommunication
Loudspeakers
CD8 / CD16
WALL-MOUNTED MONITORED PAGING CONSOLE
CD8 CD16
MAIN CHARACTERISTICS The CD8 / CD16 paging console is a remote paging interface with Access Level 2 protection in
Wall-mounted enclosure

compliance with EN54-16. Compatible with DIVA8 and IDA8 PAVA systems, the unit serves up
to eight zones individually with an All-Call option. Zone selection buttons and Fireman

microphone are encased in a heavy-duty IP30 wall-mounted metal box with a lockable door.
Monitoring of microphone capsule

The CD8 / CD16 console use the same architecture as the PPM paging console, a junction box
8/16 zone selection buttons

embedded into the enclosure multiple units by daisy-chaining wiring(only the first console in the
All-call button
chain is under monitored). The maximum distance between units is up to 100M. The zone buttons
LED test button
of CD8 / CD16 represent a single zone or group of zones and can be easily programmed through
Power indicator
the system GUI using “drag and drop” functionality. The Push- To-Talk button can be programmed
for PTT or latching operation. The status indicators including Power, EVAC and Fault which show
EVAC indicator

the status of all the zone are also provided with.

EN54-16 certified

The CD8 / CD16 is powered over RS485 via CAT-5 (FTP/STP), however if power is not available over
RS485 it can be locally powered by using a 24V DC supply.
Note: There are two versions of the CD8 / CD16 paging console with identical hardware and
functionality but different firmware for compatibility with different systems.
CD8-AS / CD16-AS: Used with IDA8 system and ECS system controllers and slaves (one CD8 /
CD16 connects to per PDC port with a maximum up to 10 units by daisy-chain wiring and
external power supply should be used for every third unit ).
CD8-G2 / CD16-G2: Used with DIVA8 system controllers [The maximum CD8 / CD16 units of
configuring with daisy-chain wiring is 1 units (only the first unit is under monitored). An external
power supply should be used for every third unit in the chain].
The ATEÏS range of security systems complies with current architectural demands requiring IP
and/or fiber-optic networking to cater for any possible PAVA design, however complex. ATEÏS
responds to Public Address and Voice Alarm requirements as stated in EN54-16, ISO 7240-16
and BS5839/8, with specific attributes for compliance in large installations.
ATEI
57
CD8 / CD16

Activity indicators
Power supply Dimensions(H x W x D)
Interface RS-485 (RJ45/CAT-5) CD8 190 x 320 x 130 mm
LED test button
(7-1/2" x 12-3/5" x 5-1/10")
Fireman microphone with Push To Talk
DC/battery power requirements CD16 130 x 350 x 130 mm
Voltage 18 - 26 VDC (5-1/10" x 13-3/4" x 5-1/10")
INTERCONNECTIONS
Power consumption Weight
Rear CD8 120 mA CD8 3.6 kg (7.9 lbs)
RJ45
for CAT-5 connection CD16 150 mA CD16 4.7 kg (10.4 lbs)
Color RAL7016
Performance
Frequency response -3 dB @ 100 Hz to 18 kHz Environmental
THD < 1% @ 1 kHz Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Europe Voice Alarm EN54-16 certified 2012 Output level Max 6 dBu Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
CE – 0359 Noise gate threshold -84 dBu ~ – 24 dBu Relative humidity 15% to 90%
according to EN50130 – 4 Attack time 8 ms Air pressure 600 to 1100 h Pa
Release time 100 ms IP rating 30
PARTS INCLUDED
Output impedance 100 Ohm Heat Dissipation
Quantities Components CD8 10 BTU/hr
1 CD8 / CD16 Monitoring speaker CD16 12 BTU/hr
1 CAT-5 cable, 10pin, 1.5 m Impedance 4 Ohm
System Connection
Cable type CAT-5, 10pin (FTP)
Length 100 m
ATEI
58
Commercial Audio
Intercommunication
Loudspeakers
CDPM
The CDPM paging console is a wall-mounted cabinet remote with Access level 2 protection in
compliance with EN 54-16. Compatible with ATEÏS audio processor, CDPM paging console
interconnects over a dedicated RS485 for power, audio and data transmit. The RS485 commu-
nication protocol with daisy-chain wiring can support up to 100 m over CAT5 cable connection.
The CDPM supports 2 channels of music input. By pressing the button for selection, the two LED
indicators shall light up and activate the music channel. The unit comprises of 24 zones / 24
buttons with Fireman microphone in a metal surface mount wall-box. It provides robust IP-30
protection. Each CDPM contains a PMM PS Master PCB with extension keypad and uses the same
architecture as for the PPM AS series of microphone consoles. Each ATEÏS audio processor is
capable to support up to 31 CDPM units per RS485 port in Master/Slave configuration.
The control buttons represent a single zone or a group of zones. All buttons can be programmed
with drag & drop features from the ATEÏS Studio software, The PTT button can be programmed for
Push To Talk function or for latching functionality.
The unit offers “Hold” and “Busy” LED signals in addition to the zone LED’s, and these features
allow an easy identification of Selection/Busy signals for users. In addition, to meet the compliance
with EN 54-16, POWER, FAULT and EVAC indicators are provided with.
Additional RCA connectors with selection buttons support local audio injection for commercial
usage. The RS485 communication protocol offers daisy chaining of up to 300 m on a simple CAT5
cable, and yet makes outlets easy to connect via a standard RJ45 connector.
SPECFICATIONS
Fireman Microphone Electrical Monitoring speaker

Power / Music Active / Talk / All Call / Release / Mains power supply Impedance 8 Ohm
Fault / Busy / Hold / EVAC / Indicator Voltage 18~26 VDC Output power 1 W @ 1 Khz
Talk / Music Selection / All Call / Release Button Power consumption 200 mA Frequency response -3 dB @ 200 to 20 kHz
Monitoring Speaker
Fireman Microphone / Music Input / Connector Performance Mechanical
Event Select Key Frequency response -3 dB @ 200 Hz to 20 kHz Dimensions(H x W x D) 220 x 483 x 68 mm
THD < 0.1% @ 1 kHz (8-1/3" x 19" x 2-1/3")
INTERCONNECTIONS
Output level Max -6 dBu Weight 3.9 kg (8.6 lbs)
Rear Noise gate threshold -84 dBu ~ – 24 dBu Color RAL7016
Attack time 8 ms
Release time 100ms Environmental
PARTS INCLUDED
Output impedance 100 Ohm Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Quantities Components Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
1 CDPM-XX System connection Relative humidity 15% to 90%
1 Junction Box Cable type / Length CAT-5, 10pin (FTP) / 100 m (max.) Air pressure 600 to 1100 h Pa
1 CAT-5 cable, 10pin, 1m IP Rating 30
ATEI
59
Commercial Audio
Intercommunication
Loudspeakers
PCP
The PCP paging console is a wall-mounted heavy duty remote with Access Level 2 protection in
compliance with EN 54-16. Compatible with ATEÏS audio processor, PCP paging console
interconnects over a dedicated RS485 for power, audio and data transmit. The RS485
communication protocol with daisy-chain wiring can support up to 100 m over CAT5 cable
connection.
The unit comprises of 16 zones / 16 buttons with Fireman microphone in a metal surface mount
wall-box. It provides robust IP-30 protection. Each PCP contains a PMM PS Master PCB with
extension keypad and uses the same architecture as for the PPM AS series of microphone consoles.
Each ATEÏS audio processor is capable to support up to 31 PCP units per RS485 port in
Master/Slave configuration.
The control buttons represent a single zone or a group of zones. All buttons can be programmed
with drag & drop features from the ATEÏS Studio software, The PTT button can be programmed for
Push To Talk function or for latching functionality.
The unit offers “Hold” and “Busy” LED signals in addition to the zone LED’s, and these features
allow an easy identification of Selection/Busy signals for users. In addition, to meet the compliance
with EN 54-16, POWER, FAULT and EVAC indicators are provided with.
SPECFICATIONS
A telephone styled microphone

Electrical Monitoring speaker
Fault / EVAC / Power / Talk / Hold / All Call /
Mains power supply Impedance 8 Ohm
Release / Busy Indicator Voltage 18~26 VDC Output power 1 W @ 1 Khz
All Call/Release/Talk Button
Power consumption 150 mA Frequency response -3 dB @ 200 to 20 kHz
Microphone Connector

Event Select Key

Performance Mechanical
Frequency response -3 dB @ 200 Hz to 20 kHz Dimensions(H x W x D) 220 x 346 x 128 mm
INTERCONNECTIONS
THD < 0.1% @ 1 kHz (8-3/5" x 13-3/5" x 5")
Rear Output level Max -6 dBu Weight 3 kg (6.6 lbs)

Noise gate threshold -84 dBu ~ – 24 dBu Color RAL7016(Main)
Attack time 8 ms
PARTS INCLUDED
Release time 100 ms Environmental
Quantities Components Output impedance 100 Ohm Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
1 PCP-XX Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
1 Junction Box System connection Relative humidity 15% to 90%
1 CAT-5 cable, 10pin, 1m Cable type / Length CAT-5, 10pin (FTP) / 100 m (max.) Air pressure 600 to 1100 h Pa
IP Rating 30
ATEI
60
Commercial Audio
Intercommunication
Loudspeakers
URC / URC 200 / DNM

PAVA SYSTEM PERIPHERALS
URC DNM
Programmable Remote Controller Digital Noise Sensing Microphone
With built-in Electronic Condenser microphone
(omnidirectional), DNM enhances the ability to
detect the surrounding background noise. With
the 0 dB modulation through the Audio Processor,
DNM component provides the Automatic Gain
Control feature and automatically adjusts the
output level of loudspeaker under any situation.
The URC AS can be fully programmed via ATEÏS
Studio software to adjust every setting: level INTERCONNECTIONS
control, preset, components' adjustments, etc. An
elegant OLED for displaying information of Rear Connector
parameters or the status. It gives extreme simple
RJ45 for CAT-5 connection (POE)
Ethernet port CAT -5 Cable
design and cost-effective consideration of with
only Two buttons [EXIT], [BACK] and a knob on RS485 port for 5.08 mm EURO Block (4Pin)
RS485 port 5.08 mm EURO Block (4Pin)
control interface. The RS485 communication
protocol allows daisy-chain wiring up to 32 units, PARTS INCLUDED
System connection
providing with a long distance from the audio
processor. Quantities Components Cable type CAT-5 (FTP)
1 DNM-485 / DNM Ethernet Max Length 100 m
Mechanical
Dimension = 84mm (W) x 33mm (L) x 84mm (H) 1 CAT-5 cable, 100 m
3-3/10" (W) x 1-3/10" (L) x 3-3/10" (H) Mechanical
Weight = 0.08KG (0.17 lbs) TECHNICAL SPECIFICATIONS
Dimensions 100mm(Diameter) x 130mm(H)
Electrical 4"(Diameter) x 5-1/10"(H)
URC200 / Ethernet Universal Programmable Weight 0.13kg (0.28 lbs)
Power supply
Remote Controller
Voltage 18-30 VDC (if no POE available) Color RAL7035
Battery Holder 250 mA
Environmental
Performance Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Frequency response -1 / +1 dBu 50~16 kHz@ 0 dBu, Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Sampling rate 48 KHz Only 1 selection Relative humidity 15% to 90%
Equivalent -80 dBu 50~16 kHz @ 600 ohm Air pressure 600 to 1100 h Pa
THD+N 0.2 % 50~16 kHz @ 0 dBu IP Rating 30
Microphone
The URC200 is an programmable remote controller Sensitivity (60 - 120 dBA) ±5dBA
(TCP/IP) for the PAVA system and the IP-media
Frequency response 50Hz to 16kHz @ -3 dB
streamers with Terracom IP Media software. The
URC200 is powered over IP and easy to integrate THD <0.2% @ 1 kHz
with current demands for room controllers like Input -40 dBu @ 1 kHz
light, curtains, sound and video control.
EIN <-80 dB
The full color display is easy to read and has a low-
power consumption to allow for long lines and
multiple devices into one system.
Mechanical
Dimension = 140mm (W) x 108mm (H) x 34mm (L)
5-1/2" (W) x 4-1/4" (H) x 1-3/10" (L)
Weight = 0.35Kg (0.7 lb)
ATEI
61
Commercial Audio
Intercommunication
Loudspeakers
Dialpad
TOUCH DIAL DEVICE FOR IDA8 SYSTEM
DialPad is a touch dial, cost-effective tabletop controller that connects to IDA8 or ECS audio processor.
By both on Local and SIP call, users shall connect to either external telephone set with phone line or
DialPad with Ethernet connector.
To activate each item by touch provides users with a user-friendly instruction. DialPad can be operated
by using the touch panel -dialing, mute, volume controls, 3-way calling, contact lists, etc. The OLED on
the front panel enhances a simple design, and the secured device information for users to monitor,
included the connection status and dialing information. All the items can be fully programmed with
Drag & Drop features from the system unit GUI software to adjust every custom settings and each item
Dialpad
can be operated via ATEÏS Studio Software or DialPad simultaneously.
DialPad provides a quick-access use with a long-distance calls and multi-paging. Connecting to Wireless
Transceiver device, its capabilities provide the freedom to limit the distance with you from room to
room without moving the base unit, with secure, the password protecting to each calls allows you to
confirm the callers to whom have the authority for multi-paging.
Wireless Transceiver is a handy remote which connects to IDA8 or ECS audio processor and provides the
wireless network for DialPad Device. By connecting to either two kinds of ports (RS485, RS232), the
Wireless Transceiver makes it easy to set up and operate with audio central unit and DialPad device. Its
capabilities enhance the freedom to limit the distance with you from room to room without moving the
base unit. With Wireless Transceiver
SPECFICATIONS
Dialpad Front Electrical Mechanical

Telephone Keypad / Function Keypad / Panel
Power supply Dimensions(H x W x D)
Display / Status LED / Buzzer Voltage Dialpad 66 x 255 x 108 mm
Dialpad Rear Dialpad 18 - 24 VDC (2-3/5" x 10" x 4-1/4")
RS485 connector / Battery Holder
Wireless Transceiver 24 VDC Wireless Transceiver 30 x 100 x 67 mm
Wireless Transceiver Front Battery Holder (1-1/5' x 4" x 2-5/8")
Power LED / Status LED
Dialpad AAA Battery x 4 Weight
Wireless Transceiver Rear Power consumption Dialpad 0.5 kg (1.1 lbs)
RS485 / RS232 / 24VDC connector
Wireless Transceiver 30 mA Wireless Transceiver 0.1 kg (0.22lbs)
Color RAL7016
INTERCONNECTIONS
Performance
Dialpad Rear Panel Display Environmental
RS485 for CAT-5 connection (PoE)
Dialpad 128*32 Pixels Monochrome (White) Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
Wireless Transceiver Rear Buzzer Sound Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
RJ45 for CAT-5 connection (POE)
Dialpad >85dBA @10cm Relative humidity 15% to 90%
RS232 connector
System connection IP Rating 30
PARTS INCLUDED
Cable type / Length
Quantities Components Dialpad CAT-5 (FTP) / 100 m (max.)
1 Wireless TransceiverXX / DialPadXX Wireless Transceiver CAT-5 (FTP) / RS232
1 CAT-5 cable, 500m 500 m / 12 m
ATEI
62
Commercial Audio
Intercommunication
Loudspeakers
URGP
ALARM INPUT INTERFACE FOR IDA8-SYSTEM AND DIVA-SYSTEM
Desktop enclosure
The URGP is a contact interface extension unit to the IDA8 System.
Secured RS232/RS485 link to controllers and

Each URGP32in / URGP 16I16O provide 32 /16 additional alarm inputs. Each input is monitored
slaves
and can be programmed to trigger a digital audio message into a specific zone or group of zones.
32 alarm inputs
The URGP is linked to the System units through an RS232 /RS485 monitored serial link.

EN54-16 certified

SPECFICATIONS
Front Electrical Mechanical

EVACUATION active indicator
Mains power supply Dimensions(H x W x D) 44 x 140 x 75 mm
FAULT indicator
Voltage 18~26 VDC (1-3/4" x 5-1/2" x 3")
POWER indicator
Power consumption 30 mA Weight 0.5 kg (1.1 lbs)
Color RAL7016
INTERCONNECTIONS
Performance
Rear Evacuation inputs Environmental
RJ45
Contact mode 5 VDC Operating temperature -5ºC ~ 55ºC (23ºF ~ 131ºF)
RS232
Voltage mode -6 dBu Storage temperature -40ºC ~ 70ºC (-40ºF ~ 158ºF)
Monitoring resistor 4.7k Ohm Relative humidity 15% to 90%
System connection IP Rating 30
Cable type / Length CAT-5 (FTP) / 100 m (max.)
CE – 0359
according to EN50130 – 4
ATEI
63
Commercial Audio
Intercommunication
Loudspeakers
List Of Peripherals
Peripherals Connection Maximum number (per port) Device

PSS AS PDC port 1 IDA8
PSS G2 PSS / PSM port 1 DIVA8G2
PSS G2E Ethernet 8 DIVA8G2
PPM-IT5 Ethernet 1 (Active Over Eth.) IDA8
PPM AS PDC port 32 IDA8
PSM PSS / PSM port 10 DIVA8G2
PSC PDC port 32 IDA8
CD8 / CD16 PDC port (IDA8), PSS / PSM port (DIVA8G2) 1 IDA8/DIVA8G2
CD-Touch PDC port (IDA8), PSS / PSM port (DIVA8G2) 1 IDA8/DIVA8G2
PCP / CDPM PDC port 32 IDA8
DialPad / Wireless Transceiver PDC port 1 IDA8
URC-AS PDC port 32 IDA8
URC200AS Ethernet Eth. Limit IDA8
DNM-485 PDC port 32 IDA8
DNM-Ethernet Ethernet Eth. Limit IDA8
URGP32in / URGP 16I16O PDC port 1 IDA8
Eth. Limit: The maximum number of IP that can be assigned over the network.
Max. Number: The max. number of peripherals through per PDC port by using a Junction Box.
The devices which connected to PDC port, PSS port and PSM port are all powered over RS485 communication protocol.
ATEI
64
65
ATEI
ATEÏS Europe B.V.

Sydneystraat 42, Rotterdam,
3047 BP, Netherlands.
SWITZERLAND - F
Phone +31 (0)10 2088690 D S- RA
AN NC
Fax +31 (0)10 2088699
RL
E-
www.ateis-europe.com
E
TH
US
Email: [email protected]
NE
A-
A E - TA I WA N -
CHIN
A - SINGA
ATEÏS Suisse SA
Chemin du Dévent 7, 1024 Ecublens,
Switzerland
Y-U
POR
Phone +41 (0)21 881 25 10
N
Fax +41 (0) 21 881 25 09
MA
-I E
ER
N
G DI
A
ATEÏS France
ZA Font Ratel - 8, rue de l'Europe
38640 Claix, France
Phone +33 (0)4 76 99 26 30
Fax +33 (0)4 76 99 26 31
ATEÏS Germany GmbH. ATEÏS Middle East

Roggensteiner Str. 15, 82140 Olching, Light Industrial Unit 11 Dubai, Silicone Oasis,
Deutschland Dubai United Arab Emirates
Phone +49 (08142) 305070-30 Phone +971 4 3262730
Fax +49 (0)8142 305070-39 Fax +971 4 3262731
Email: [email protected] Email: [email protected]
Penton/ATEÏS USA. ATEÏS FAR EAST CORP.

21 Sabin St. Pawtucket, RI 02860, USA 2F,No.60, Xinghua 2nd Rd, Tanzi,
Phone 888-883-8383 Taichung 427, Taiwan
Fax +888-821-2121 Phone +886-4-25333820
www.penton-usa.com Fax +886-4-25333830
Email: [email protected] Email: [email protected]
ATEÏS China
Room 610, No.255 Wubao Road, Minxing district,
Shanghai, China
Phone +021-54495191/92
Fax +021-54495193
ATEÏS SE Pte Ltd.

Blk5002 Ang Mo Kio Avenue 5,
#03-01B Techplace II, Singapore 569871
Phone +65 64811968
Fax +65 64811960

PAVA Catalog en V5

Uploaded by

Copyright:

Available Formats

PAVA Catalog en V5

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PAVA Catalog en V5

Uploaded by

Copyright:

Available Formats

Public Address - Voice Alarm

ATEI Audio Distribution over IP

Public Address & Voice Alarm

D ELIVERING Y OUR M ESSAGE

IDA8 Digital Public Address and Voice Alarm series is

ATEIS has developed and will continue developing

D ELIVERING Y OUR M ESSAGE

Networkable PAVA System

IDA8 is a third-generation modular

IDA8 responds to Public Address

Networkable PAVA System

Networkable PAVA System

IDA8 is a third-generation modular system that complies with current

MAIN CHARACTERISTICS CONNECTIVITY:

Support a maximum up to 31 slave units in ATEÏS Local-Net

CONTROLS AND INDICATORS PARTS INCLUDED Amplifier Capacity (per zone)

INTERCONNECTIONS TECHNICAL SPECIFICATIONS Dimensions (With 19" rack mount brackets)

4 monitored paging console inputs

IDA8 is a third-generation modular system that complies with

CONNECTIVITY: MAIN CHARACTERISTICS

CONTROLS AND INDICATORS PARTS INCLUDED

Front Quantities Components Amplifier Capacity (per zone)

IDA8 is a third-generation modular system that complies with

CONNECTIVITY: MAIN CHARACTERISTICS

supplies are monitored. Programmable of 4 user levels

CONTROLS AND INDICATORS PARTS INCLUDED

Front Quantities Components Amplifier Capacity (per zone)

Telephone Card (Optional)

IDA8 is a third-generation modular system that complies with current

MAIN CHARACTERISTICS CONNECTIVITY:

Support a maximum up to 31 slave units in ATEÏS Local-Net

CONTROLS AND INDICATORS PARTS INCLUDED

Front Quantities Components Amplifier Capacity (per zone)

Line outputs (Optional audio output card)

CONTROLS AND INDICATORS PARTS INCLUDED

Front Quantities Components Amplifier Capacity (per zone)

CONTROLS AND INDICATORS PARTS INCLUDED

Front Quantities Components Amplifier Capacity (per zone)

Telephone Card (Optional)

Line outputs (Optional audio output card)

Figure 1: Equal Mode Configuration

Priority 1~20 sources shall be used by the EVAC and

Note: Make sure the Watt unit of each group must

Figure 3: Backup Sharing Mode Configuration

Scenario 1: [Equal Mode + Unequal Mode]

Scenario 2: [Backup Sharing Mode + Equal Mode]

Scenario 3: [Unequal Mode + Backup Sharing Mode]

Scenario 4: [Multiple wiring with 8 amplifiers + Equal Mode]

Scenario 5: [ IDA8C ( Matrix Mode ) + IDA8C / IDA8SAB ( Switch Mode ) ]

RU-MAIN / CTL / PDC

RU-MAIN / CTL / PDC

CONTROLS AND INDICATORS

Front LED display: power, Primary IDA8 system active,

LED display: power, Primary IDA8 system active,

Connections: Screw terminals blocks

Secondary IDA8 system Active

Secondary IDA8 system watchdog

Secondary IDA8 system Active, Expansion

Switching time: 6 seconds (IDA8 watchdog period)

NET-C1, 2x RJ45 Port A & Port B