Scribd
Upload
103 views2 pages

Introduction To Tech. Mathematics (MATH1018) Assignment 4

This document provides instructions for Assignment 4 for the course Introduction to Tech. Mathematics (MATH1018). The assignment is due on November 29th and is worth 35 marks, which is 3% of the total course grade. It covers concepts from Chapter 2 of the textbook and tests students' geometry skills. Students must show all work and will lose marks for plagiarism or late submissions. The assignment contains 8 questions involving calculations of distances, areas, volumes, and ratios related to shapes like triangles, circles, cylinders, cones, and irregular river channels.

Uploaded by

Vivek sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
103 views2 pages

Introduction To Tech. Mathematics (MATH1018) Assignment 4

This document provides instructions for Assignment 4 for the course Introduction to Tech. Mathematics (MATH1018). The assignment is due on November 29th and is worth 35 marks, which is 3% of the total course grade. It covers concepts from Chapter 2 of the textbook and tests students' geometry skills. Students must show all work and will lose marks for plagiarism or late submissions. The assignment contains 8 questions involving calculations of distances, areas, volumes, and ratios related to shapes like triangles, circles, cylinders, cones, and irregular river channels.

Uploaded by

Vivek sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

Introduction to Tech.

Mathematics (MATH1018)
Assignment 4.

DUE Date : 29-11-2018 Marks 35


Percentage 3%

Purpose: To test the skills acquired by the students in the Chapters of “Geometry”
Instructions:
1. The student will get full marks only if he enumerates all the steps involved
2. Plagiarism in any form would lead to a very high penalty
3. Late assignments will be penalised.If you submit an assignment a day after the deadline
then you will be marked “0” for it.

Resources: The assignment covers the Chapters 2.

Requirements: You should hand the assignment complete in all respects by the due date
hand written
Evaluation: Your assignment would be marked on the basis of how well you have
understood the concepts and your ability to apply them.

Q1. Find the indicated distances between the straight irrigation ditches. The vertical ditches
are parallel.
3.20m 4.75m 6.25m

3.05m a b

d (4marks)
c 5.05 m

Q2.Find the area of each triangle.

7.62mm
Alt.=2.2 ft
(6 marks)

7.6ft 16mm

Q3.Part of an electric circuit is wired in the configuration of a rhombus and one of its
altitudes as shown. What is the length of wire in this part of the circuit. (3 marks)

12mm

16mm
Q4. Using a tape measure, the circumference of a tree is found to be 112in. What is the
diameter of the tree(assuming a circular cross section) (3 marks)

Q5. A window designed between semi circular regions is as shown. Find the area of the
window. (4 marks)

90 cm

180cm
Q6. Surroundings taken across a river channel give the following values of distances from one shore
with the corresponding depth of the channel.
Distance (ft) 0 50 100 150 200 250 300 350 400 450 500
Depth(ft) 5 12 17 21 22 25 26 16 10 8 0
(6 marks)

Q7. A propane tank is constructed in the shape of a cylinder with a hemisphere at each
end .find the volume of the tank. (4
marks)

Q8. The radius of a cylinder is twice as long as the radius of cone, and the height of the
cylinder is half as long as the height of the cone. What is the ratio of the volume of the
cylinder to that of the cone. (5 marks)

You might also like