Final Thang1.
Final Thang1.
com
1 Which three addresses belong to the category of private IP addresses? (Choose three.)
10.0.0.1
127.0.0.1
150.0.0.1
172.16.0.1
192.168.0.1
200.100.50.1
Refer to the exhibit. Host A wants to connect to host B on a different network. Which three IP addresses
assigned to host A to enable this connectivity? (Choose three.)
172.16.11.36
172.16.11.95
172.16.11.88
172.16.11.70
172.16.11.64
172.16.11.67
3
http://vuongnetpro.blogspot.com
Refer to the exhibit. Host A wants to access e-mail. Which destination socket number will be used to com
this request?
10.10.1.2:53
0007.A7B8.0008:25
10.10.1.3:23
10.10.1.3:25
Refer to the exhibit. A network technician wants to connect host A to the console of a Cisco switch to ini
configuration. What type of cable is required for this connection?
straight-through cable
crossover cable
rollover cable
serial cable
5 Which subnet mask will allow 2040 hosts per subnet on the IP network 10.0.0.0?
http://vuongnetpro.blogspot.com
255.255.0.0
255.255.254.0
255.255.252.0
255.255.248.0
255.255.240.0
255.255.255.128
Refer to the exhibit. Host A is transmitting data to host B. Which address combination will be used as the
leaves the Router1 Fa0/1 interface?
Destination IP: 192.168.72.2 Source MAC: 0007.C2B4.3421
Destination IP: 192.168.10.4 Source MAC: 0030.8596.DE81
Destination IP: 192.168.10.4 Source MAC: 0007.C2B4.3421
Destination IP: 192.168.72.2 Source MAC: 0030.8596.DE81
7Which memory contents will change as a result of using the Router# erase startup-config command on a ro
RAM
ROM
flash
NVRAM
8
http://vuongnetpro.blogspot.com
Refer to the exhibit. A user wants to access the Internet from the PC. A part of the running configuration of
is shown. Which default gateway IP address should be configured at the PC to enable this access?
10.1.192.2
10.1.192.54
10.1.192.1
192.31.7.1
9
http://vuongnetpro.blogspot.com
Refer to the exhibit. In a network, Hosts A and B are exchanging segments at the transport layer. Which t
statements are true about this exchange? (Choose two.)
Host A is transferring files to host B using FTP.
Host A will send the next segment containing data for this session starting with byte number 11.
The segment from the destination host indicates that 11 bytes have been received successfully.
Host A is initiating a Telnet session to host B.
Host B can send the next segment of the data starting with byte number 2.
10
http://vuongnetpro.blogspot.com
Refer to the exhibit. Which logical topology describes the exhibited network?
star
ring
point-to-point
multi-access
11
Refer to the exhibit. The network administrator remotely accesses the CLI of RouterB from PC1 using a s
connection. Which statement is true about this connection?
The Telnet server process is running on PC1.
Only the exchange of the Telnet username and password is encrypted.
The GET request is sent to RouterA to retrieve data.
The SSH service is used to connect PC1 to RouterB.
12
Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Which list cor
identifies the component or protocol used at each numbered stage of the diagram?
1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA
http://vuongnetpro.blogspot.com
13 Which three statements are true about network layer addressing? (Choose three.)
It uses the last octet of the IP address to identify the network.
It supports data communications between networks.
It is configured by the network technician.
It is a 16-bit IPv4 address.
It prevents broadcasts.
It uniquely identifies each host.
14
Refer to the exhibit. Which two facts can be determined about the topology? (Choose two.)
Four collision domains are present.
One logical network is represented.
Two broadcast domains are present.
Three networks are needed.
Three logical address ranges are required.
application layer
network layer
presentation layer
session layer
transport layer
What two conclusions are evident from these commands? (Choose two.)
Users who attempt to connect to the console port of the router must enter a password.
The entries permit access through the console by the use of j1mdi2 as the password.
The entries eliminate the need for authentication.
Access through the console will be denied because the console configuration is incomplete.
The entries prevent passwords from being displayed as plain text.
18
Refer to the exhibit. A technician uses the nslookup command on the PC and views the output that is dis
in the exhibit. What does abc.xyz.local in the output represent? (Choose two.)
the hostname of the PC
the hostname of the DHCP server
the hostname of the router
the primary domain name server for the host
the IP address of the website resolver1.abc.local
Two routers are connected via their serial ports in a lab environment. The routers are configured with val
http://vuongnetpro.blogspot.com
19 addresses, but they cannot ping each other. The show interface serial0/0 command shows that the serial0
interface is up but the line protocol is down. What could be the cause of this problem?
The no shutdown command has not been applied to the interfaces.
The clock rate command has not been entered on the DCE interface.
The interface timers are not cleared.
The FastEthernet interface is emulating a serial interface by assigning it a timing signal.
20
Refer to the exhibit. A user wants to view the current configuration. The output of the ipconfig/all comm
displayed in the exhibit. What three facts can be determined from the output? (Choose three.)
The IP address is obtained from the DHCP server.
This PC cannot communicate with other networks.
The network can have 14 hosts.
The prefix of the computer address is /25.
The IP address is routable on the Internet.
The assigned address is a private address.
A network administrator uses the copy startup-config running-config command on a router to make
21 configuration changes. Which component is affected by this command?
ROM
NVRAM
RAM
flash
22
http://vuongnetpro.blogspot.com
Refer to the exhibit. Host A sends a frame with the destination MAC address as FFFF.FFFF.FFFF. What
will the switch take for this frame?
It will drop the frame.
It will send the frame back to host A.
It will send the frame to all hosts except host A.
It will forward the frame to the default gateway.
23
Refer to the exhibit. An employee wants to access the organization intranet from home. Which intermedi
device should be used to connect the organization intranet to the Internet to enable this access?
hub
switch
router
http://vuongnetpro.blogspot.com
24
Refer to the exhibit. The router of the company failed and was replaced. After the replacement, hosts C a
the Education office are able to ping each other, but they are unable to access the hosts in the Accounts o
What is the likely cause of the problem?
The IP address at the fa0/0 interface of the router is incorrectly configured.
The subnet mask at the fa0/1 interface of the router is incorrectly entered.
The IP address at the serial interface of the router is incorrectly configured.
The hosts in the Accounts office are not on the same subnet as the hosts in the Education office.
25
Refer to the exhibit. The tracert command used from host X to host Y was successful. What is the correc
sequence of intermediary network devices that will be present in the trace list?
switch A, switch D, switch G, host Y
http://vuongnetpro.blogspot.com
26
Refer to the exhibit. Cable 1 and Cable 2 are wired for specific physical layer requirements. The table list
segment by number and the cable that connects the network components on that segment. Which three se
have the correct cables installed? (Choose three.)
segment 1
segment 2
segment 3
segment 4
segment 5
segment 6
28 A network administrator wants to restrict access to the router privileged EXEC mode. Which password sh
the administrator use?
enable
aux
console
VTY
29
Refer to the exhibit. The host was disconnected from switch 2 and connected to switch 1. Which combina
IP address, subnet mask, and default gateway should be assigned to this host to allow it to function in the
network?
IP address: 10.10.9.37 Subnet mask: 255.255.255.240 Default gateway: 10.10.9.35
IP address: 10.10.9.37 Subnet mask: 255.255.255.224 Default gateway: 10.10.9.35
IP address: 10.10.9.29 Subnet mask: 255.255.255.248 Default gateway: 10.10.9.35
IP address: 10.10.9.32 Subnet mask: 255.255.255.224 Default gateway: 10.10.9.35
IP address: 10.10.9.37 Subnet mask: 255.255.255.224 Default gateway: 196.1.105.6
IP address: 10.10.9.63 Subnet mask: 255.255.255.224 Default gateway: 10.10.9.35
Refer to the exhibit. The network administrator uses the netstat command to display the open, active, and
running TCP connections on a networked host. The exhibit displays the output of this command. Which t
facts can be determined from this output for accessing www.cisco.com? (Choose two.)
The source port indicates that the session is an http session.
The connection is not successful.
The source port of the host is 3166.
The destination port is 80.
The source port does not support communication with the destination port that is listed.
The source port indicates that a UDP session has been initiated.
32
Refer to the exhibit. A router, the table of which is shown, receives a packet that is destined for 192.168.9
How will the router treat the packet?
It will drop the packet.
It will forward the packet via FastEthernet 0/1.
It will forward the packet to the next hop address.
http://vuongnetpro.blogspot.com
33
Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this attempt, a fra
captured at the FastEthernet interface fa0/1 of router Y. The packet inside the captured frame has the IP s
address 172.16.1.5, and the destination IP address is 172.16.7.24. What is the source MAC address of the
at the time of capture?
0040.8596.DE82
0060.7320.B826
0060.7320.D632
0010.4F74.AC09
0040.8596.DE81
34
http://vuongnetpro.blogspot.com
Refer to the exhibit. While configuring a network, a technician wired each end of a Category 5e cable as
Which two statements are true about this setup? (Choose two.)
The cable is suitable for connecting a switch to a router Ethernet port.
The cable is suitable for connecting dissimilar types of devices.
The cable is unusable and must be rewired.
The cable is terminated in a way that the transmit pin is wired to the receive pin.
The cable simulates a point-to-point WAN link.
35
Refer to the exhibit. A PC is connected to a network. Which action will verify that the PC can communicat
default gateway?
Use the ping 127.0.0.1 command.
Use the ipconfig command.
Use the ipconfig/all command.
Use the ping 10.0.0.254 command.
How does the transport layer allow a host to maintain multiple, simultaneous communication streams acro
36different applications?
It uses error control mechanisms.
It uses a connectionless protocol only for multiple simultaneous transmissions.
It uses multiple Layer 2 source addresses.
It uses multiple ports.
37 While configuring a router, a network technician wants to name the router. Which prompt should the tech
see when entering the hostname command?
http://vuongnetpro.blogspot.com
Router>
Router#
Router(config)#
Router(config-line)#
Which three IPv4 addresses represent valid network addresses for a subnet? (Choose three.)
38 192.168.9.64/28
192.168.9.146/28
192.168.9.96/28
192.168.9.129/26
192.168.9.51/26
192.168.9.64/26
39
Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the differen
devices?
Connection 1 - straight-through cable Connection 2 - straight-through cable Connection 3 - crossover
Connection 1 - straight-through cable Connection 2 - crossover cable Connection 3 - rollover cable
Connection 1 - crossover cable Connection 2 - rollover cable Connection 3 - straight-through cable
Connection 1 - crossover cable Connection 2 - straight-through cable Connection 3 - crossover
Connection 1 - straight-through cable Connection 2 - rollover cable Connection 3 - crossover cable
Which three statements are true about transport layer protocols? (Choose three.)
40 The UDP transport layer protocol provides for low overhead data delivery.
The TCP transport layer protocol uses windowing and acknowledgments for reliable transfer of d
The TCP and UDP port numbers are used by application layer protocols.
The TCP transport layer protocol provides services to direct the data packets to their destination host
The UDP transport layer protocol is a connection-oriented protocol.
The UDP transport layer protocol keeps track of all the data segments in each conversation.
41
http://vuongnetpro.blogspot.com
Refer to the exhibit. The NAT functionality of the router is enabled to provide the PC with Internet acces
Which IP address can be assigned to router interface Fa0/0?
10.0.0.1
172.16.1.1
209.165.201.1
192.168.1.1
What are two characteristics of the data link layer? (Choose two.)
42 It segments and reorders the data.
It exchanges the frames between nodes.
It defines the method by which network devices place data onto the media.
It manages the transfer of data between the processes that run on each host.
It retrieves signals from the media and restores them to their bit representations.
43 An organization has decided to use IP addresses in the range 172.20.128.0 to 172.20.143.255. Which
combination of network ID and subnet mask identifies all IP addresses in this range?
Network ID: 172.20.128.0 Subnet mask: 255.255.255.0
Network ID: 172.20.128.0 Subnet mask: 255.255.0.0
Network ID: 172.20.128.0 Subnet mask: 255.255.224.0
Network ID: 172.20.128.0 Subnet mask: 255.255.240.0
Network ID: 172.20.128.0 Subnet mask: 255.255.255.240
Which two types of media can provide bandwidth up to 1 Gb/s? (Choose two.)
44 10 BASE-T
100 BASE-T
100 BASE-FX
1000 BASE-TX
http://vuongnetpro.blogspot.com
1000 BASE-SX
45 Which range of port numbers is assigned dynamically to client applications when initiating a connection
server?
0 to 255
49152 to 65535
1024 to 49151
0 to 1023
46 Which device should be used for enabling a host to communicate with another host on a different networ
switch
hub
router
host
47
Refer to the exhibit. The headers added at each layer are shown.
Which layer adds the destination and source process numbers to ensure that data is delivered to the correc
application?
physical layer
data link layer
network layer
transport layer
48
http://vuongnetpro.blogspot.com
49
Refer to the exhibit. All devices in the network use default configurations. How many broadcast domains a
this topology?
3
5
7
9
11
50
http://vuongnetpro.blogspot.com
Refer to the exhibit. Host A and B are unable to communicate with each other. What is the reason for this
Host A is assigned a network address.
Host B is assigned a multicast address.
Host A and host B belong to different networks.
The gateway addresses are network addresses.