Scribd Logo
Upload

Welcome to Scribd!

  • 34 views

    NZL 7 High Build Vinyl Ester

    Uploaded by

    candra

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    NZL 7 High Build Vinyl Ester

    Uploaded by

    candra
    34 views2 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    34 views2 pages

    NZL 7 High Build Vinyl Ester

    Uploaded by

    candra

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Data Sheet

    ©Copyright
    Valid From: 05 March 2008

    NAKI 7 NZL TM

    High Build Vinyl Ester

    Charateristics : is a high buid Vinyl Ester glassflake, it use for metal repair.
    It also can be moulded and machined

    Recommended : Ideal for protection of Metal & Concrete substates in arduous condition.
    NZL 7 has high chemical & acid resistance and is suitable for tank lining,
    pump & valve repair and protection. When fully cured, it is readily
    machined.

    Health & Safety : Read and observe health & safety datasheet prior to application

    Colour : Off white

    Mixing Ratio : 100 : 1 to 100 : 2 by Weight (Base : Activator)


    Add all the activator to the base and mix thoroughly, ensuring no
    unmixed materials remain. The ratio should always within these limit.
    Measure the correct proportion of catalyst for the amount of base &
    carefully add this to the base, using a suitable clean implement.

    Mix only as much material as may be used during the limited pot
    life.

    Surface Preparation : Metals: abrasive blast cleaning to Sa 2½ (ISO 8501-1:2007), SSPC


    SP10 or NACE #2 will be suitable. A minimum surface profile of 75
    Microns is required. Concrete: please refer to concrete surface
    preparation guidelines.

    Application Equipment : Natural Bristle Brush, Trowel, or float

    Application Method : This viscious material is preferably applied over the top of NRZ 7.
    NZL 7 can be applied at thicknesses up to 3,000 Micron in a single
    film and can be built up by the use of multiple coats to any required
    thickness.
    Pot Life : Approximately 1 Hour 20°C. This time will vary significantly with
    temperature.

    Volume Solids : 99%

    Thinners : Do not thin. The use of thinners in NZL 7 will significantly affect
    product performance

    PT. NUSCACO ANTI KOROSI INDONESIA, Jl. Raya Cakung Cilincing KM.1/7, Jakarta, Indonesia
    T: +6221460033 I F: +62214600337
    Data Sheet
    ©Copyright
    Valid From: 05 March 2008

    NAKI 7 NZL TM

    High Build Vinyl Ester

    Recommended DFT : 1,000 to 3,000 Microns in single applied. Depend on service and
    atmospheric duty, may be built up to to any desired thickness for
    repair.
    Theoretical Spreading Rate : 2. at 1000 Micron dft.
    The amount may increase depent upon geometry and nature of work
    undertaken and the skill and care of application

    Cure Time : Tack Free : Approximately 3 Hours at 30°C


    Full Cure : Approximately 2 days at 30°C (Will vary
    significantly with temperature)

    OverCoating Time : Minimum : 10 Hours at 25°C


    Maximum : 72 Hours (These times may be substantially
    shorter at high ambient temperature)

    Storage & Handling : The product must be ideally stored in a cool and well ventilated
    place, protected from heat and direct sunlight. Containers must be
    kept tightly closed before and after use.

    Flash Point : 40°C

    Packaging : 20 Liter Composite kit.

    Shelf Life : A Minimum of 1 year in unopened tins stored below 20°C

    Cleaning Solvent : Acetone, Xylene, Toluene, MEK

    Disclaimer

    The information in this data sheet is given to the best of our knowledge based on laboratory testing and
    practical experience. However, product is often used under condition beyond our control; we cannot
    guarantee anything but the quality of product itself. We reserve the right to modify from time to time
    according to manufacturer experience and continuous development program.

    PT. NUSCACO ANTI KOROSI INDONESIA, Jl. Raya Cakung Cilincing KM.1/7, Jakarta, Indonesia
    T: +6221460033 I F: +62214600337

    You might also like