Lenovo H5s Series User Guide

Machine type: 10093/2561/4746 [H520s]
10107/3230 [H505s]
10118/6286 [H535s ES]
10119/6287 [H535s Non-ES]
10126/90A5 [H515s]
10131/90A9 [H530s ES]
10132/90AB [H530s Non-ES]
H5s Series
User Guide
Version 1.0 2013.03
31504385
Downloaded from www.Manualslib.com manuals search engine

Important Safety Information
Before using this manual, it is important that you read and understand all of the
related safety information for this product. Refer to the Safety and Warranty Guide
that you received with this product for the latest safety information. Reading and
understanding this safety information reduces the risk of personal injury or product
damage.
The interface and functions shown in this User Guide are provided for reference
only and may differ from actual product appearance. Product design and
specifications may be changed without notice.
Danger: Be aware of extremely hazardous or potentially lethal situations.
Attention: Be aware of possible damage to programs, devices, or data.
Note: Pay attention to this important information.
© Copyright Lenovo 2013. All rights reserved.

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered
pursuant a General Services Administration “GSA” contract, use, reproduction, or
disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

Contents
Important Safety Information
Using the Computer Hardware.................................................. 1

Front view of the chassis.............................................................................2
Rear view of the chassis..............................................................................3
Basic connector instructions.......................................................................8
Connecting your computer..........................................................................9
5.1 Audio configuration instructions...........................................................10
Connecting the power cord.......................................................................11
Display connecting instructions when playing Blu-ray Discs.......................12
Connecting to the Internet.........................................................................12
Wired keyboard (selected models only).....................................................13
Using Windows 8....................................................................... 15

Switching between the main Windows 8 interfaces...................................16
The Charms Bar........................................................................................16
Shutting down the computer.....................................................................16
Switching between apps...........................................................................17
Closing an app..........................................................................................17
Opening other system programs...............................................................17
Windows Help and Support......................................................................17
Using the Rescue System......................................................... 19

OneKey Recovery.....................................................................................20
Driver and Application Installation..............................................................21
Using the Software.................................................................... 23

Lenovo Support........................................................................................24
Contents i

Troubleshooting and Confirming Setup.................................. 25
Troubleshooting Display Problems.............................................................26
Troubleshooting Audio Problems...............................................................27
Troubleshooting Software Problems..........................................................28
Troubleshooting Problems with Optical Drives and Hard Disks..................28
Special considerations for troubleshooting Windows.................................29
Windows Help and Support......................................................................30
BIOS setup utility.......................................................................................30
Performing Daily Maintenance Tasks.........................................................31
Hardware Replacement Guide................................................. 33

Locations..................................................................................................36
Replacing hardware..................................................................................45
Appendix.................................................................................... 55
Declaration................................................................................................55
Trademarks...............................................................................................56
Energy Star Statement..............................................................................57
Enabling ErP compliance mode.................................................................58
ii Contents

Using the Computer Hardware
This chapter contains the following

topics:
 Introduction to the computer hardware
 Information on computer connections
Note: The descriptions in this chapter

might be different from what you see on
your computer, depending on the computer
model and configuration.
User Guide 1

Front view of the chassis
Attention: Be careful not to block any air vents on the computer. Blocked
air vents can cause overheating.
Power button
Memory card reader (selected models only)
USB connectors
Optical drive eject button
Headphone connector
Optical Drive (selected models only)
Hard disk drive indicator
Microphone connector
Note: This computer only can be placed in a vertical position.
Attention: Do not insert 3-inch discs into the optical drive.
2 User Guide

Rear view of the chassis
(If the rear view configuration shown in this chapter is different from the rear of your
computer, please refer to the rear of your computer.)
Lenovo H505s
On-board VGA connector

WiFi antenna (selected models only)
HDMI connector (selected models only)
USB 2.0 connectors
USB 3.0 connectors
Ethernet connector
Audio connectors
Power connector
Expansion card slot
User Guide 3

Lenovo H515s

USB 2.0 connectors
USB 3.0 connectors
Ethernet connector
Audio connectors
Power connector
Cable clip
PCI Express X 16 graphics adapter slot (some models are equipped with a
graphics card)
PCI Express X 1 adapter slot (some models are equipped with USB 3.0 or
TV tuner card)
4 User Guide

Lenovo H520s
USB connectors
Ethernet connector
Audio connectors
graphics card)
TV tuner card)
Power connector
Voltage selection switch (selected models only)
User Guide 5

Lenovo H530s

USB 3.0 connectors
USB 2.0 connectors
Ethernet connector
Audio connectors
graphics card)
TV tuner card)
Power connector
6 User Guide

Lenovo H535s
11
12
USB 2.0 connectors

USB 3.0 connectors
USB 2.0 connectors
Ethernet connector
Audio connectors
graphics card)
TV tuner card)
Power connector
User Guide 7

Note: If your model has two VGA monitor connectors, be sure to use the
connector on the graphics adapter.
Attention: Do not open the WiFi antenna cover.
Basic connector instructions

Note: Your computer may not have all of the connectors described in this
section.
Connector Description
Microphone Use this connector to attach a microphone to your
computer when you want to record sound or if you use
speech-recognition software.
Headphone Use this connector to attach headphones to your
computer when you want to listen to music or other
sounds without disturbing anyone.
Audio line-in connector Used to receive audio signals from an external audio
device, such as a stereo system. When you attach an
external audio device, a cable is connected between
the audio line-out connector of the device and the audio
line-in connector of the computer.
Audio line-out connector Used to send audio signals from the computer to
external devices, such as powered stereo speakers
(speakers with built-in amplifiers), headphones,
multimedia keyboards, or the audio line-in connector on
a stereo system or other external recording device.
Memory card reader Use to view and share digital photos, music, and videos,
stored on a media card.
Power connector Connect to the power cable. The appearance of this
connector may vary.
USB connector Use this connector to attach a device that requires a
USB connection.
Ethernet connector Use this connector to attach the computer to an
Ethernet-type local area network.
VGA connector Used to attach a VGA monitor or other devices that use
a VGA monitor connector.
8 User Guide

DVI connector Used to attach a DVI monitor or other devices that use a
DVI monitor connector.
HDMI connector Connect to the HDMI connector on your display or TV.
(optional)
TV-Tuner connector Only supported on systems with an optional TV tuner
(optional) card.
Note: If your computer is equipped with a wireless keyboard or mouse,

follow the installation instructions for those devices.
Connecting your computer

Use the following information when connecting your computer.
• Look for the small connector icons on the back of your computer. Match the
connectors to the icons.
• If your computer cables and connector panel have color-coded connectors,
match the color of the cable end with the color of the connector.
Note: Your computer may not have all of the connectors described in this
section.
Check the position of the voltage-selection switch on

the rear of the computer. Use a ballpoint pen to slide
the switch if necessary.
Note: Some computers do not have a voltage switch. These computers
control voltage automatically.
• If the voltage supply range is 100-127 V AC, set the switch to 115 V.
• If the voltage supply range is 200-240 V AC, set the switch to 230 V.

230
115
User Guide 9

5.1 Audio configuration instructions
This model of computer supports the transformation of stereo sound into 5.1
surround sound.
Use the following guides when connecting to the 5.1 surround audio device:
Blue line-in connector

Surround
Green line-out connector
Front channel
Pink Mic-in connector
Center-LFE
The configurations are as followings:

1. Right click the Sound icon in system property bar and select Playback
devices option to setup the sounds in the pop-up dialog box.
2. Select a playback device from the Playback dialog box, then click the
Configure button to configure it.
3. Select 5.1 surround from audio channels in the pop-up Speaker setup dialog
box to proceed with the speaker setup by following the prompts.
4. 5.1 surround sound can be used once this configuration procedure is
complete.
Note: If the audio configuration interfaces above are different from

those on your computer, you may use the above steps as a reference to
configure the 5.1 surround sound audio device system in your actual audio
configuration interface and read the electronic Help information for further
assistance.
10 User Guide

Connecting the power cord
Connect the power cord to an electrical outlet. We recommend using a grounded
connection or a surge protector.
Some models are equipped with Power Adapter.
User Guide 11

Display connecting instructions when
playing Blu-ray Discs
Note: Only some models are equipped with Blu-ray optical drive.
Check the connectors available on your computer and display and select an
appropriate cable according to the table below. Other types of cables do not meet
the requirements of the Blu-ray standard.
You need to purchase the cable separately if the computer is not equipped with
the corresponding cable.
This table will help you to identify the connectors on your computer and display.
Connection Type Computer Cable Display

DVI to DVI
(DVI cable)
DVI to HDMI
(DVI-HDMI cable)
HDMI to HDMI
(HDMI cable)
HDMI to DVI
(HDMI-DVI cable)
Connecting to the Internet

To connect to the Internet, you’ll need a contract with an Internet Service Provider
(ISP) and some hardware.
IPSs and ISP offerings vary by country. Contact your ISP for offerings available in
your country.
Your computer is designed to support a wireless (selected models only) or wired
network that connects your computer to other devices.
Wired network connection

For wired networks, connect one end of an Ethernet cable (purchased separately)
to the Ethernet connector on your computer, and then connect the other end to
the network router or broadband modem. Consult your ISP for detailed setup
instructions.
Note: Broadband modem and router installation procedures vary
depending on the manufacturer. Follow the manufacturer’s instructions.
12 User Guide

Wireless network connection
For wireless networks, you can use the built-in wireless LAN antenna to access
your wireless home network.
To connect your computer to the wireless network:
1. Move the cursor to the top right or bottom right corner of the screen, then click
Settings. (If your computer is equipped with touch screen, swipe in from the
right edge of the screen, then tap Settings.)
2. Click or tap the network icon , then select the name of your router. Click or
tap Connect, then follow the steps on the screen.
Test the wireless network by opening your Web browser and accessing any Web
site.
Wired keyboard (selected models only)

LVT —— After entering Windows, press this key to launch the LVT (Lenovo
Vantage Technology) program, Lenovo’s pre-loaded Home PC software.
In addition to its own functions, the LVT program will allow you to start
other Windows compatible software specially configured to run on this
model of computer.
Notes:
• Some models are not equipped with the LVT program.
• The LVT key on the keyboard is disabled in the models
without the LVT program.
F2 —— Your computer has the Lenovo Rescue System installed. To learn more
about this program, repeatedly press and release the F2 key once
turning on the computer until the Lenovo Rescue System opens.
User Guide 13

14 User Guide

Using Windows 8

topics:
 Switching between the main Windows 8 interfaces
 The Charms Bar
 Shutting down the computer
 Switching between apps
 Closing an app
 Opening other system programs
 Windows Help and Support
Attention: The Windows 8 operating system

is provided by Microsoft Corporation. Please
use it in accordance with the END USER
LICENSE AGREEMENT (EULA) between you
and Microsoft. For any question related to the
operating system, please contact Microsoft
directly.
User Guide 15

Switching between the main Windows 8
interfaces
Windows 8 comes with two main user interfaces: the Start Screen and the
Windows desktop.
To switch from the Start Screen to the Windows desktop, do one of the following:
• Select the Windows desktop tile on the Start Screen.
• Press the Windows key + D.
To switch from the desktop to the Start Screen, do one of the following:
• Select Start from the Charms Bar.
• Move the cursor to the bottom left corner, then select the Start Screen
thumbnail when it is displayed.
• Press the Windows key .
The Charms Bar

Charms provide new and faster ways to perform many basic tasks.
To display the charms, do one of the following:
• Move the cursor to the top right or bottom right corner of the screen.
• If your computer is equipped with touch screen, swipe in from the right edge of
the screen.
• Press the Windows key + C.
Shutting down the computer

To shut down the computer:
1. Move the cursor to the top right or bottom right corner of the screen, then click
Settings. (If your computer is equipped with touch screen, swipe in from the
right edge of the screen, then tap Settings.)
2. Select Power → Shutdown.
16 User Guide

Switching between apps
Sometimes you want to get back to an app you were just using, or quickly switch
through your recent apps.
To switch between apps:
Move the cursor to the top left corner, then click to bring in the next app. (If your
computer is equipped with touch screen, swipe in from the left edge of the screen
to bring in the next app.)
Closing an app
To close an app, do one of the following:
• Move the cursor to the top left corner of the screen. When the thumbnail
appears, drag it to the bottom of the screen.
• Move the cursor to the top edge of the screen. When the cursor becomes a
hand, drag the app page to the bottom of the screen.
• If your computer is equipped with touch screen, swipe in from the top edge of
the screen. When the app page becomes smaller, drag it to the bottom of the
screen.
Opening other system programs

There is a fast way to open other system programs.
To open the menu, do one of the following:
• Move the cursor to the bottom left corner of the screen. When the thumbnail
appears, right-click with the mouse to open the menu.
• Press the Windows key + X.
Windows Help and Support

If you have a problem with the operating system, see the Windows Help and
Support file. To open the Windows Help and Support file, do one of the following:
• Select the Settings charm, then select Help.
• Press the Windows key + F1.
You can read the Windows Help and Support file on your computer. You can also
get online help and support by clicking on one of the two links listed under More
to explore.
User Guide 17

18 User Guide

Using the Rescue System

topics:
 OneKey Recovery
 Driver and Application Installation
Attention: Using OneKey Recovery will result

in loss of data.
• You can restore the C: drive of the computer
to factory default settings or to the last system
backup status using OneKey Recovery. If you
do this, all of the existing data on drive C: will
be lost, but the content and format of the other
partitions of the hard disk drive will remain
unchanged.
• If you want to install an operating system and
back it up with OneKey Recovery, you must
format the C: partition in NTFS format and
install the operating system on the C: partition.
Otherwise, the OneKey Recovery system cannot
run.
User Guide 19

Note about the service partition:
The files and relevant data used by the rescue system are saved in the service
partition. Deleting this partition will make the rescue system unusable. For more
detailed information, see the following instructions:
From the Search charm, select Apps → Control Panel → Administrative Tools
→ Computer Management → Disk Management, you can see the service
partition, which must not be deleted.
Note: The recovery files and relevant data used by the rescue system are
saved in the service partition. If the service partition is deleted or damaged
by someone other than authorized Lenovo service personnel, Lenovo will
not be liable for any losses arising therefrom in any way.
OneKey Recovery
OneKey Recovery is an easy-to-use application. You can use it to restore your
computer to the system default or to a previously backed up state.
Detailed Operation Procedure

1. Repeatedly press and release the F2 key once turning on the computer until
the Lenovo Rescue System opens, then select OneKey Recovery.
Note: System Recovery will overwrite all of the data on the C: drive. To
prevent loss of data, be sure to back up relevant data before performing
system recovery.
2. Follow the on-screen instructions to select the backup task you want to restore
from and the disk where you want to install the operating system, then press
Next to start the restore.
3. Please wait during the process of system recovery. Do not interrupt the
operation during the recovery process.
4. After the system is recovered successfully, the software will prompt you to
restart the computer. Restart the computer and start the operating system.
20 User Guide

Driver and Application Installation
The Driver and Application Installation function in the rescue system provides a
way for the user to conveniently reinstall all of the Lenovo applications and drivers
that were shipped with your Lenovo hardware.
Method 1: Automatic Installation

Repeatedly press and release the F2 key once turning on the computer until the
Lenovo Rescue System opens, then select Drivers and Application Installation.
Follow the on-screen prompts to install the Lenovo drivers and applications. Click
OK to start installing the Lenovo Drivers and Application Installation software.
The system will restart. After the system has restarted, the drivers and application
installation process will continue until it has completed.
Method 2: Manual Installation

In the Windows system, Select Driver and Application Installation from the
Search charm.
After starting the procedure, install the drivers and software manually by following
the prompts.
Notes:
1. Do not install software which is already installed on the computer.
2. Make sure that the Drivers and Application Installation software has
been automatically installed before starting the operating system. The
manual installation function can only be used after the software has
been installed.
User Guide 21

22 User Guide

Using the Software

topic:
 Software instructions
Note: The interface and functionality of these

features will depend on which software
was shipped with the computer model you
purchased.
User Guide 23

Lenovo Support
The Lenovo Support program enables you to register your computer with Lenovo,
download and view user manuals for your computer, get the warranty information
of your computer, and explore help and support information.
To open this program, do the following:

Click the Lenovo Support icon from the Start Screen or Search Screen.
The main functions of this program are listed below. (This program supports
online upgrades. The functions shown below are for reference only, functionality will
depend on the program icons currently displayed.)
Registration
Registration provides you with access to product support, upgrades and alerts on
topics. Take advantage of award-winning Lenovo services.
User Guide
The User Guide provides more information about your computer.
Service and Warranty

You can extend the warranty of your computer through this option. Lenovo
provides flexible options to meet your personal or business needs.
24 User Guide

Troubleshooting and
Confirming Setup

topic:
 Troubleshooting and Problem Resolution
User Guide 25

Solving Problems
Follow these tips when troubleshooting your computer:
• If you added or removed a part before the problem started, review the
installation procedures to ensure that the part is correctly installed.
• If a peripheral device does not work, ensure that the device is properly
connected.
• If an error message appears on the screen, write down the exact message.
This message may help support personnel diagnose and fix the problem(s).
• If an error message occurs in a program, see the Help document of this
program.
Troubleshooting Display Problems

Problem: Blank screen or no image is displayed on the monitor.
Troubleshooting and problem resolution:
1. Check to see if the monitor has been turned on; if not, press the Power button.
2. Check to see if the monitor power cord is loose; if so, plug the power cord
securely into the monitor.
3. Check to see if the signal cable to the monitor is securely connected to the
connector on the computer graphics card; if not, shut down the computer
then connect the signal cable of the monitor securely to the connector on the
computer graphics card.
Problem: You need to change the display property settings.

Setting display background and icon properties:
1. Right-click the desktop anywhere except over an icon, then select Personalize
from the pop-up menu.
2. From here, select the appropriate options to:
• Change the desktop background
• Select a screen saver
• Select Windows color options for borders and taskbar
• Select a themes
3. Right-click the desktop anywhere except over an icon, then select Screen
resolution from the pop-up menu to change the appearance.
26 User Guide

Problem: Ripple on screen.
1. Check to see if any of the following devices are located less than one meter
from the computer: refrigerators, electric fans, electric dryers, UPS systems,
regulators, fluorescent lamps or other computers that may be generating
magnetic interference.
2. Move any interfering devices away from the computer.
3. If the problem persists, contact Lenovo Service.
Troubleshooting Audio Problems

Problem: No sound from the integrated speakers.
• Adjust the Windows volume control — select the speaker icon from the
Settings Charm or click the arrow on taskbar to show the hidden icons in
Windows desktop mode, then click the speaker icon. Ensure that the volume
is turned up and the sound is not muted. Adjust the volume, bass, or treble
controls to eliminate distortion.
• Reinstall the audio driver.
• Disconnect any headphones from the headphone connector — sound from
the speakers is automatically disabled when headphones are connected to the
computer’s side-panel headphone connector.
Problem: No sound from headphones.

• Check the headphone cable connection — ensure that the headphone cable is
securely inserted into the headphone connector.
• Adjust the Windows volume control — select the speaker icon from the
Settings Charm or click the arrow on taskbar to show the hidden icons in
Windows desktop mode, then click the speaker icon. Ensure that the volume is
turned up and the sound is not muted.
User Guide 27

Troubleshooting Software Problems
Problem: You are unable to exit a running program normally.
1. Press the Ctrl, Alt and Delete keys at the same time, then select the Task
Manager option from the pop-up dialog box.
2. Select the problem program, then click the End Task button.
Problem: You need to install or uninstall a program.

Problem resolution:
During installation never abort the install process by powering the system off or
through other drastic means. This can cause system program problems or even
failure during system initialization.
During the uninstall process, never directly delete the files or folders. This is
harmful to the operating system, and might cause a system-wide malfunction.
Use the following procedure to properly uninstall programs:
1. Back up all documents and system settings related to the program before
removing it.
2. If the program has its own uninstaller, run it directly to uninstall the program.
3. If the program does not have its own uninstaller, then select Apps → Control
Panel from the Search charm.
4. From the Control Panel, choose Programs → Programs and Features.
5. Find the applicable program from the Programs and Features dialog box and
then select Uninstall/Change.
6. Perform the instructions displayed to uninstall the software.
Troubleshooting Problems with Optical Drives

and Hard Disks
Problem: The Optical drive is unable to read a CD/DVD.
1. Check to determine if there is an optical drive icon in the resource manager
of the operating system. If not, restart your computer. If there is still no icon,
contact Lenovo Service. Otherwise, continue with the next step of this
procedure.
28 User Guide

2. Confirm that the CD/DVD has been properly placed in the drive. If not, reload
the CD or DVD. Otherwise, continue with the next step of this procedure.
3. Check the specifications that came with your computer to confirm that this
optical drive is capable of reading this type of CD or DVD.
4. If the CD/DVD cannot be read, replace it with a known good CD/DVD such as
one that was shipped with the computer.
5. If the known good CD cannot be read, visually check the operating side of the
CD/DVD for defects.
Problem: The capacity of the hard disk, as indicated by the system, is less than
the nominal capacity.
Troubleshooting and problem resolution: For computers equipped with the
OneKey Recovery feature, the system recovery feature needs to occupy some
hard disk space. This may account for the apparent hard disk capacity deficit.
Further Technical Explanation: The nominal capacity of the hard disk is

expressed in the decimal system as 1000 bytes. But the actual hard disk capacity
is expressed in the binary system as 1024 bytes (For example, the nominal
capacity 1G is 1000M, while the actual capacity 1G is 1024M).
The capacity of the hard disk shown in Windows can be calculated according to
the calculations in the following example:
The nominal capacity of the hard disk is 40G, while its actual capacity
should be: 40 x 1000 x 1000 x 1000/(1024 x 1024 x 1024) = 37G.
If the Service partition of 3G - 3 x 1000 x 1000 x 1000/(1024 x 1024 x

1024) = 2.79G is subtracted, the capacity of the hard disk shown in the
system can be obtained.
The capacity of the hard disk as calculated using this method may be slightly
different from the actual capacity due to the rounding of totals.
Special considerations for troubleshooting

Windows
Record the following information as it may be useful later when troubleshooting
system problems:
The drivers for this computer model only support the Windows 8 system.
User Guide 29

Windows Help and Support
If you have a problem with the operating system, see the Windows Help and
Support file. To open the Windows Help and Support file, do one of the following:
• Select the Settings charm, then select Help.
• Press Windows key + F1.
You can read the Windows Help and Support file on your computer. You can also
get online help and support by clicking on one of the two links listed under More
to explore.
BIOS setup utility

What is the BIOS setup utility?
The BIOS setup utility is ROM-based software. It communicates basic computer
information and provides options for setting boot devices, security, hardware
mode, and other preferences.
How can I start the BIOS setup utility?

To start the BIOS setup utility:
1. Shut down the computer.
2. Repeatedly press and release the F1 key once turning on the computer to start
the Setup Utility program.
How can I change the boot mode?

There are two boot modes: UEFI and Legacy. To change the boot mode, start the
BIOS setup utility and select Startup → Boot Priority, then set boot mode to UEFI
or Legacy support on the boot menu.
When do I need to change the boot mode?

The default boot mode for your computer is the UEFI mode. If you need to install
a legacy Windows operating system (any operating system before Windows 8) on
your computer, you must change the boot mode to Legacy support. The legacy
Windows operating system cannot be installed if you don’t change the boot mode.
30 User Guide

Performing Daily Maintenance Tasks
Cleaning the computer components
Because many of the computer components consist of sophisticated integrated
circuit boards, it is very important to periodically clean the computer to prevent
dust buildup. The cleaning supplies you need to clean the components include:
a vacuum cleaner, a soft cotton cloth, pure water (preferably purified or distilled
water) and cotton swabs.
Attention: Before you clean your computer, disconnect the computer

from the electrical outlet. Clean your computer with a soft cloth
dampened with water. Do not use liquid or aerosol cleaners, which may
contain flammable substances.
Note: To avoid damaging the computer or display, do not spray cleaning

solution directly onto the display. Only use products specifically designed
for cleaning displays, and follow the instructions included with the product.
The following are general methods for cleaning the components:

• You can use a soft cloth to remove dust on the surface of the computer, the
monitor, the printer, the speakers and the mouse.
• You can use a vacuum cleaner to clean in otherwise inaccessible corners.
• To clean the keyboard thoroughly, shut down the computer and scrub it gently
with a wet cloth. Do not use the keyboard until it is dry.
Do not do any of the following:

• Allow water to enter the computer.
• Use a heavily dampened cloth.
• Spray water directly onto the surface of the monitor or inside the computer.
LCD monitor should be cleaned daily. Use a dry cloth to brush dust from the
monitor and keyboard every day. Keep all surfaces clean and free of grease stains.
User Guide 31

32 User Guide

Hardware Replacement Guide

topics:
 Identifying internal components
 Identifying parts on the system board
 Removing the computer cover
 Removing the front bezel
 Replacing a memory module
 Replacing a hard disk drive
 Replacing an optical drive
 Replacing the keyboard and mouse
User Guide 33

Overview
This guide is intended to be used by customers who are replacing Customer
Replaceable Units (CRUs) as well as trained service personnel who are replacing
Field Replaceable Units (FRUs). In this guide, CRUs and FRUs will often be referred
to as parts.
Note: Trained service personnel should refer to the Hardware Maintenance

Manual (HMM) for parts ordering information.
This guide does not include procedures for all parts. It is expected that cables,
switches, and certain mechanical parts can be replaced by trained service
personnel without the need for step-by-step procedures.
Note: Use only parts provided by Lenovo®.
The description of the TV-Tuner card in this manual applies only to computer
models that have a TV-Tuner card installed. It does not apply to computer models
that do not have a TV-Tuner card installed.
This guide contains procedures for replacing the following parts:

• Memory modules
• Hard disk drive
• Optical drive
• Keyboard, Mouse (wired)
Safety information for replacing CRUs

Do not open your computer or attempt any repair before reading the “Important
safety information” in the Safety and Warranty Guide that was included with your
computer. If you no longer have this copy of the Safety and Warranty Guide, you
can obtain one online from the Support Web site at http://support.lenovo.com.
34 User Guide

Additional information resources
If you have Internet access, the most up-to-date information for your computer is
available from the World Wide Web.
You can find the following information:
• CRU removal and installation information
• Publications
• Troubleshooting information
• Parts information
• Links to other useful sources of information
To access this information, go to http://support.lenovo.com.
Tools required
To disassemble the computer, you need the following tools:
• Wrist grounding strap and conductive mat for preventing electrostatic discharge
• Flat screwdriver
• Phillips screwdriver
• Hex screwdriver
• Plastic flat screwdriver
• Plastic tweezers
Note: The screws for different components vary in size. During the
disassembly procedure, group the screws with their corresponding
components to avoid a mismatch when replacing the components.
User Guide 35

Handling static-sensitive devices
Static electricity, although harmless to you, can seriously damage computer
components.
When you are replacing a part, do not open the anti-static package containing the
new part until the defective part has been removed from the computer and you are
ready to install the new part.
When you handle parts and other computer components, take these precautions
to avoid static electricity damage:
• Limit your movement. Movement can cause static electricity to build up around
you.
• Always handle parts and other computer components carefully. Handle
adapters, memory modules, system boards, and microprocessors by the
edges. Never touch any exposed circuitry.
• Prevent others from touching the parts and other computer components.
• Before you replace a new part, touch the anti-static package containing the
part to a metal expansion slot cover or other unpainted metal surface on
the computer for at least two seconds. This reduces static electricity in the
package and your body.
• When possible, remove the new part from the anti-static packaging and install
it directly in the computer without setting the part down. When this is not
possible, place the anti-static package that the part came in on a smooth, level
surface and place the part on it.
• Do not place the part on the computer cover or other metal surface.
Locations
This section provides illustrations to help locate the various connectors, controls
and components of the computer. To remove the computer cover, refer to
“Removing the computer cover”.
Locating components and connectors

The following illustrations will help you to locate the various components and
connectors in your computer.
36 User Guide

Internal components
The following illustrations show the components inside your computer.
Lenovo H505s/H515s
3
Heatsink and CPU fan System board

Optical disk drive and bay Hard disk drive
User Guide 37

Lenovo H520s/H530s
Heatsink and CPU fan System board

Power supply
38 User Guide

Lenovo H535s
System board Heatsink and CPU fan

Power supply
User Guide 39

Identifying parts on the system board
The system board (sometimes called the planar or motherboard) is the main circuit
board in your computer. It provides basic computer functions and supports a
variety of devices that are factory-installed or that you can install later.
Lenovo H505s
1 2 3
13 12 11 10 9 8 7
Microprocessor and heat sink Microprocessor fan header

Memory slots (2) Power connector
Thermal sensor header Front panel connector
Battery SATA connectors (2)
Mini PCI-E slot Front USB connectors (2)
Clear CMOS jumper PCI express X 1 adapter slot
Front audio connector
40 User Guide

Lenovo H515s
1 2 3 4 5 6 7
10
16 15 14 13 12 11
System fan header Clear CMOS jumper

Battery Microprocessor and heat sink
Microprocessor fan header SATA connectors (2)
Memory slots (2) Hard disk drive power connector
LPC debug header Front panel connector
System fan header PCI express X 16 adapter slot
Front USB connectors (2) Mini PCI-E slot
PCI express X 1 adapter slot Front audio connector
User Guide 41

Lenovo H520s
1 2 3 4 5
8
9
20 19 18 17 16 15 14 13 12 11 10
12V power connector Microprocessor and heat sink

Microprocessor fan header Memory slots (2)
Thermal sensor header Power connector
Battery SATA connectors (3)
eSATA connector Power fan header
Front panel connector Clear CMOS jumper
Front USB connectors (2) Mini PCI-E slot
Mode switch connector Serial (COM2) connector
PCI express X 1 adapter slots (3) Front audio connector
PCI express X 16 adapter slot System fan header
42 User Guide

Lenovo H530s
1 2 3 4 5
7
19
18
8
9
17 16 15 14 13 12 11 10

Thermal sensor header Hard disk drive power connector
Power connector Power fan header
SATA connectors (3) Front panel connector
Front USB connectors (2) LPC debug header
Mini PCI-E slot PCI express X 1 adapter slots (3)
Clear CMOS jumper Front audio connector
Battery
User Guide 43

Lenovo H535s
1 2 3 4 5
16
15
8
14
9
13 12 11 10

Thermal sensor header Mini PCI-E slot
Power connector Power fan header
SATA connectors (3) Front panel connector
Front USB connector Front USB connector
Front audio connector PCI express X 1 adapter slots (3)
44 User Guide

Replacing hardware
Attention: Do not remove the computer cover or attempt any repair

before reading the “Important safety information” in the Safety and
Warranty Guide that was included with your computer or in the Hardware
Maintenance Manual (HMM) for the computer. To obtain copies of the
Safety and Warranty Guide or HMM, go to the Support Web site at
http://support.lenovo.com.
Note: Use only parts provided by Lenovo.
General information
Pre-disassembly instructions
Before proceeding with the disassembly procedure, make sure that you do the
following:
1. Turn off the power to the system and all peripherals.
2. Unplug all power and signal cables from the computer.
3. Place the system on a flat, stable surface.
Removing the computer cover
Attention: Turn off the computer and wait 3 to 5 minutes to let it cool
down before removing the cover.
To remove the computer cover:

1. Remove any media (disks, CDs, or memory cards) from the drives, shut down
your operating system, and turn off the computer and all attached devices.
2. Unplug all power cords from electrical outlets.
3. Disconnect all cables attached to the computer. This includes power cords,
input/output (I/O) cables, and any other cables that are connected to the
computer. Refer to “Locating connectors on the rear of the computer”.
4. Remove the 2 screws that secure the computer cover at the rear of the
chassis.
User Guide 45

5. Slide the computer cover toward the rear of the chassis to remove.
Note: For this procedure, it helps to lay the computer on a flat, stable
surface.
46 User Guide

Removing the front bezel
To remove the front bezel:

1. Remove the computer cover. Refer to “Removing the computer cover”.
surface.
2. Remove the front bezel by releasing the three plastic tabs inside the chassis
and pushing the bezel outward as shown.
3. To reattach the bezel, align the plastic tabs on the bottom of the bezel with the
corresponding holes in the chassis, and then snap it into position at the bottom
and top of the chassis.
4. Refer to “Completing the installation”.
User Guide 47

Replacing an optical drive

To replace an optical drive

2. Remove the front bezel. Refer to “Removing the front bezel”.
3. Remove the 2 screws that secure the optical disk drive bay to the chassis.
4. Slide out the optical disk drive bay, then lift it up.
48 User Guide

5. Disconnect the data and power cables from the rear of the optical drive.
6. Remove the 2 screws that secure the optical drive to the optical drive bay
and push the optical drive straight out of the front of the drive bay.
3
4
7. Slide the new optical drive into the bay from the front, then attach it to the drive
bay with the screws.
8. Connect the data and power cables to the new optical drive.
9. Slide the optical disk drive bay back, then push it in and and reattach it to the
chassis with the screws.
10. Reattach the front bezel. Refer to “Removing the front bezel”.
User Guide 49

Replacing the hard disk drive

To replace the hard disk drive

2. Remove the front bezel. Refer to “Removing the front bezel”.
3. Remove the optical disk drive bay. Refer to “Replacing an optical drive”.
4. Remove the screw that secures the hard disk drive bay to the chassis.
5. Slide out the hard disk drive bay, then lift it up. Disconnect the data and power
cables from the hard disk drive.
50 User Guide

6. Remove the 4 screws that secure the hard disk drive to the bay.
7. Slide the hard disk drive out of the bay.
8. Install the new hard disk drive.

(1) Insert the new hard disk drive into the drive bay.
(2) Screw back the 4 screws on the drive bay.
9. Attach the data and power cables to the new hard disk drive.
10. Line up the hard disk drive bay, then slide it in. Reattach it to the chassis with
the screws.
11. Reattach the optical drive disk bay. Refer to “Replacing an optical drive”
12. Reattach the front bezel. Refer to “Removing the front bezel”.
Replacing a memory module

User Guide 51

To replace a memory module:
surface.
2. Locate the memory module connectors. Refer to “Locating components”.
3. Remove the memory module being replaced by opening the retaining clips as
shown.
4. Position the new memory module over the memory connector. Make sure
the notch on the memory module is correctly aligned with the connector
key on the system board. Push the memory module straight down into the
connector until the retaining clips close.
52 User Guide

Replacing the keyboard and the mouse
To replace the keyboard:

1. Remove any media (disks, CDs, or memory cards) from the drives, shut down
your operating system, and turn off the computer and all attached devices.
2. Unplug all power cords from electrical outlets.
3. Locate the connector for the keyboard. Refer to “Locating connectors on the
rear of the computer” and “Locating connectors on the front of the computer”.
Note: Your keyboard will be connected to the USB connector at either the
front or the rear of the computer.
4. Disconnect the failing keyboard cable from the computer and connect the new
keyboard cable to the same connector.
5. The mouse can be replaced using the same method.
Completing the installation

After replacing the parts, you need to close the computer cover and reconnect
cables, including telephone lines and power cords. Also, depending on the part
that was replaced, you might need to confirm the updated information in the Setup
Utility program. Refer to “Starting the Setup Utility” in the Hardware Maintenance
Manual.
To complete the part installation:

1. Ensure that all components have been reassembled correctly and that no tools
or loose screws are left inside your computer. Refer to “Locating components”,
“Front view of the chassis” and “Rear view of the chassis” for the location of the
various components.
2. Make sure that the cables are routed correctly before replacing the computer
cover.
User Guide 53

3. Position the computer cover on the chassis so that the rail guides on the
bottom of the computer cover engage the rails. Then, push the computer cover
closed until it snaps into position. Screw back the 2 screws on the chassis.
4. Reconnect the external cables and power cords to the computer. Refer to
“Locating connectors on the front of the computer” and “Locating connectors
on the rear of the computer”.
Note: In most areas of the world, Lenovo requires the return of the
defective CRU. Information about this will come with the CRU or will come
a few days after the CRU arrives.
54 User Guide

Appendix.
Declaration
Thank you for using Lenovo products.
Carefully read all documents shipped with your computer before you install and
use the product for the first time. Lenovo is not responsible for any loss except
when caused by installation and operations performed by Lenovo professional
service personnel. You are responsible if you fail to operate the product according
to instructions and requirements in the manuals included with your computer, or
operate the product inappropriately.
This manual could include technical inaccuracies or typographical errors. Changes
are made periodically to the information herein; these changes will be incorporated
in new editions of the publication.To provide better service, Lenovo reserves the
right to improve and/or modify the products and software programs described in
the manuals included with your computer, and the content of the manual, at any
time without additional notice.
The manuals included with your computer are provided to help you use Lenovo’s
products appropriately. For the configuration of the product, refer to the related
contract (if any) or product packing list, or consult the distributor for the product
sales.
The content of the manuals included with your computer is protected by copyright
laws and rules. None of the manuals included with your computer may be
reproduced or transcribed by any means or translated into any language without
prior written permission of Lenovo.
The software interface and function and hardware configuration described in
the manuals included with your computer might not match exactly the actual
configuration of the computer that you purchase.You are welcome to contact us
about the manuals included with your computer. For the latest information or any
questions or comments, contact or visit the Lenovo Web site:
Service Web site: http://support.lenovo.com
User Guide 55

Trademarks
Lenovo and the Lenovo logo, IdeaCentre and IdeaCentre logo are trademarks of
Lenovo in the United States, other countries, or both.
Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of
companies.
Intel Inside is a trademark of Intel Corporation in the U.S. and/or other countries.
AMD, the AMD Arrow logo, ATI, AMD Athlon, AMD LIVE!, AMD Opteron, AMD
Phenom, AMD Sempron, Catalyst, Cool ‘n’ Quiet, CrossFire, PowerPlay, Radeon,
and The Ultimate Visual Experience are trademarks of Advanced Micro Devices,
Inc.
Other company, product, or service names referred to herein or in other Lenovo
publications may be trademarks or service marks of others.
All rights reserved.
Names or marks of certain companies mentioned in the manuals included with
your computer or this document do not necessarily indicate that related software
or hardware is included. The actual configuration of the product depends on the
packing list description.
56 User Guide

Energy Star Statement
ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency

and the U.S. Department of Energy aimed at saving money and protecting the
environment through energy efficient products and practices.
Lenovo is proud to offer our customers products with an ENERGY STAR compliant
designation. The following machine types have been designed and tested to
conform to the ENERGY STAR program requirement for computers at the time
of manufacture. For more information about ENERGY STAR ratings for Lenovo
computers, go to http://www.lenovo.com.
• 4746
• 3230
• 6286
• 10126/90A5
• 10131/90A9
By using ENERGY STAR compliant products and taking advantage of the power-
management features of your computer, you reduce the consumption of electricity.
Reduced electrical consumption contributes to potential financial sayings, a cleaner
environment, and the reduction of greenhouse gas emissions.
For more information about ENERGY STAR, go to: http://www.energystar.gov.
Lenovo encourages you to make efficient use of energy an integral part of your
day-to-day operations. To help in this endeavor, Lenovo has preset the following
power-management features to take effect when your computer has been inactive
for a specified duration:
ENERGY STAR power-management features, by operating system.
Microsoft Windows Vista, Windows 7 and Windows 8
Power plan: Balanced
• Turn off the display: After 10 minutes
• Put the computer to sleep: After 25 minutes
• Advanced power settings:
- Turn off hard disk drives: After 20 minutes
- Hibernate: Never
User Guide 57

To awaken your computer from a Sleep or System Standby mode, press any
key on your keyboard. For more information about these settings, refer to your
Windows Help and Support information system.
Enabling ErP compliance mode

You can enable the energy-related products directive (ErP) compliance mode
through the Power menu in the Setup Utility program. This mode reduces
electricity consumption when your computer is in standby mode or turned off.
To enable ErP compliance mode in the Setup Utility program, do the following:
1. Repeatedly press and release the F1 key when turning on the computer to start
the Setup Utility program.
2. From the Setup Utility program main menu, select Power → ErP and press
Enter.
3. Select Enabled and press Enter.
4. Press F10 to save changes and exit the Setup Utility program. Press Enter
when prompted to confirm.
Note: When ErP compliance mode is enabled, you only can wake up your
computer by pressing the power switch.
58 User Guide

Lenovo H5s Series User Guide

Uploaded by

Copyright:

Available Formats

Lenovo H5s Series User Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lenovo H5s Series User Guide

Uploaded by

Copyright:

Available Formats

Machine type: 10093/2561/4746 [H520s]

Version 1.0 2013.03

Downloaded from www.Manualslib.com manuals search engine

Danger: Be aware of extremely hazardous or potentially lethal situations.

Attention: Be aware of possible damage to programs, devices, or data.

Note: Pay attention to this important information.

© Copyright Lenovo 2013. All rights reserved.

Downloaded from www.Manualslib.com manuals search engine

Important Safety Information

Using the Computer Hardware.................................................. 1

Using Windows 8....................................................................... 15

Using the Rescue System......................................................... 19

Using the Software.................................................................... 23

Downloaded from www.Manualslib.com manuals search engine

Hardware Replacement Guide................................................. 33

Downloaded from www.Manualslib.com manuals search engine

This chapter contains the following

Note: The descriptions in this chapter

Downloaded from www.Manualslib.com manuals search engine

Note: This computer only can be placed in a vertical position.

Attention: Do not insert 3-inch discs into the optical drive.

Downloaded from www.Manualslib.com manuals search engine

On-board VGA connector

Downloaded from www.Manualslib.com manuals search engine

On-board VGA connector

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

HDMI connector (selected models only)

Downloaded from www.Manualslib.com manuals search engine

USB 2.0 connectors

Downloaded from www.Manualslib.com manuals search engine

Attention: Do not open the WiFi antenna cover.

Basic connector instructions

Downloaded from www.Manualslib.com manuals search engine

Note: If your computer is equipped with a wireless keyboard or mouse,

Connecting your computer

Check the position of the voltage-selection switch on

Downloaded from www.Manualslib.com manuals search engine

Blue line-in connector

Green line-out connector

Pink Mic-in connector

The configurations are as followings:

Note: If the audio configuration interfaces above are different from

Downloaded from www.Manualslib.com manuals search engine

Some models are equipped with Power Adapter.

Downloaded from www.Manualslib.com manuals search engine

Connection Type Computer Cable Display

Connecting to the Internet

Wired network connection

Downloaded from www.Manualslib.com manuals search engine

Wired keyboard (selected models only)

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

This chapter contains the following

Attention: The Windows 8 operating system

Downloaded from www.Manualslib.com manuals search engine

The Charms Bar

Shutting down the computer

Downloaded from www.Manualslib.com manuals search engine

Opening other system programs