Chapter 6 Ansers PDF

6
Circular Motion and Other

Applications of Newton’s Laws
CHAPTER OUTLINE
6.1 Extending the Particle in Uniform Circular Motion Model

6.2 Nonuniform Circular Motion
6.3 Motion in Accelerated Frames
6.4 Motion in the Presence of Velocity-Dependent Resistive Forces
* An asterisk indicates a question or problem new to this edition.
ANSWERS TO OBJECTIVE QUESTIONS
OQ6.1 (a) A > C = D > B = E = 0. At constant speed, centripetal acceleration is

largest when radius is smallest. A straight path has infinite radius of
curvature. (b) Velocity is north at A, west at B, and south at C. (c)
Acceleration is west at A, nonexistent at B, east at C, to be radially
inward.
OQ6.2 Answer (a). Her speed increases, until she reaches terminal speed.
OQ6.3 (a) Yes. Its path is an arc of a circle; the direction of its velocity is
changing. (b) No. Its speed is not changing.
OQ6.4 (a) Yes, point C. Total acceleration here is centripetal acceleration,
straight up. (b) Yes, point A. The speed at A is zero where the bob is
reversing direction. Total acceleration here is tangential acceleration, to
the right and downward perpendicular to the cord. (c) No. (d) Yes,
point B. Total acceleration here is to the right and either downwards or
upwards depending on whether the magnitude of the centripetal
acceleration is smaller or larger than the magnitude of the tangential
acceleration.
283
© 2014 Cengage Learning. All Rights Reserved. May not be scanned, copied or duplicated, or posted to a publicly accessible website, in whole or in part.
284 Circular Motion and Other Applications of Newton’s Laws
OQ6.5 Answer (b). The magnitude of acceleration decreases as the speed

increases because the air resistance force increases, counterbalancing
more and more of the gravitational force.
OQ6.6 (a) No. When v = 0, v2/r = 0.
(b) Yes. Its speed is changing because it is reversing direction.
OQ6.7 (i) Answer (c). The iPod shifts backward relative to the student’s hand.
The cord then pulls the iPod upward and forward, to make it gain
speed horizontally forward along with the airplane. (ii) Answer (b).
The angle stays constant while the plane has constant acceleration.
This experiment is described in the book Science from your Airplane
Window by Elizabeth Wood.
ANSWERS TO CONCEPTUAL QUESTIONS
CQ6.1 (a) Friction, either static or kinetic, exerted by the roadway where it
meets the rubber tires accelerates the car forward and then maintains
its speed by counterbalancing resistance forces. Most of the time static
friction is at work. But even kinetic friction (racers starting) will still
move the car forward, although not as efficiently. (b) The air around
the propeller pushes forward on its blades. Evidence is that the
propeller blade pushes the air toward the back of the plane. (c) The
water pushes the blade of the oar toward the bow. Evidence is that the
blade of the oar pushes the water toward the stern.
CQ6.2 The drag force is proportional to the speed squared and to the effective
area of the falling object. At terminal velocity, the drag and gravity
forces are in balance. When the parachute opens, its effective area
increases greatly, causing the drag force to increase greatly. Because
the drag and gravity forces are no longer in balance, the greater drag
force causes the speed to decrease, causing the drag force to decrease
until it and the force of gravity are in balance again.
CQ6.3 The speed changes. The tangential force component causes tangential
acceleration.
CQ6.4 (a) The object will move in a circle at a constant speed.
(b) The object will move in a straight line at a changing speed.
CQ6.5 The person in the elevator is in an accelerating reference frame. The
apparent acceleration due to gravity, “g,” is changed inside the
elevator. “g” = g ± a
CQ6.6 I would not accept that statement for two reasons. First, to be “beyond
the pull of gravity,” one would have to be infinitely far away from all
Chapter 6 285
other matter. Second, astronauts in orbit are moving in a circular path.

It is the gravitational pull of Earth on the astronauts that keeps them in
orbit. In the space shuttle, just above the atmosphere, gravity is only
slightly weaker than at the Earth’s surface. Gravity does its job most
clearly on an orbiting spacecraft, because the craft feels no other forces
and is in free fall.
CQ6.7 This is the same principle as the centrifuge. All the material inside the
cylinder tends to move along a straight-line path, but the walls of the
cylinder exert an inward force to keep everything moving around in a
circular path.
CQ6.8 (a) The larger drop has higher terminal speed. In the case of spheres,
the text demonstrates that terminal speed is proportional to the square
root of radius. (b) When moving with terminal speed, an object is in
equilibrium and has zero acceleration.
CQ6.9 Blood pressure cannot supply the force necessary both to balance the
gravitational force and to provide the centripetal acceleration to keep
blood flowing up to the pilot’s brain.
CQ6.10 The water has inertia. The water tends to move along a straight line,
but the bucket pulls it in and around in a circle.
CQ6.11 The current consensus is that the laws of physics are probabilistic in
nature on the fundamental level. For example, the Uncertainty
Principle (to be discussed later) states that the position and velocity
(actually, momentum) of any particle cannot both be known exactly, so
the resulting predictions cannot be exact. For another example, the
moment of the decay of any given radioactive atomic nucleus cannot
be predicted, only the average rate of decay of a large number of nuclei
can be predicted—in this sense, quantum mechanics implies that the
future is indeterminate. How the laws of physics are related to our
sense of free will is open to debate.
SOLUTIONS TO END-OF-CHAPTER PROBLEMS
Section 6.1 Extending the Particle in

Uniform Circular Motion Model
P6.1 We are given m = 3.00 kg, r = 0.800 m. The string will break if the
tension exceeds the weight corresponding to 25.0 kg, so
Tmax = Mg = (25.0 kg)(9.80 m/s2) = 245 N
When the 3.00-kg mass rotates in a horizontal circle, the tension causes
the centripetal acceleration,
mv 2
so T=
r
Then
rT ( 0.800 m ) T ( 0.800 m ) Tmax
v2 = = ≤
m 3.00 kg 3.00 kg
=
( 0.800 m ) ( 245 N ) = 65.3 m 2 /s 2
3.00 kg
This represents the maximum value of v2, or
0 ≤ v ≤ 65.3 m/s
ANS. FIG. P6.1
which gives
0 ≤ v ≤ 8.08 m s
P6.2 (a) The astronaut’s orbital speed is found from Newton’s second law,
with
2
∑ Fy = may : mgmoon down = mv down
r
solving for the velocity gives
v= g moon r = (1.52 m s )(1.7 × 10

2 6
m + 100 × 103 m )
v = 1.65 × 103 m s
2π r
(b) To find the period, we use v = and solve for T:
T
2π ( 1.8 × 106 m )
T= = 6.84 × 103 s = 1.90 h
1.65 × 103 m s
Chapter 6 287
P6.3 (a) The force acting on the electron in the Bohr model of the
hydrogen atom is directed radially inward and is equal to
mv 2 ( 9.11 × 10 kg ) ( 2.20 × 10 m s )
−31 6 2
F= =
r 0.529 × 10−10 m
= 8.33 × 10−8 N inward
v 2 ( 2.20 × 10 m s )
6 2
(b) a= = −10
= 9.15 × 1022 m s 2 inward
r 0.529 × 10 m
v2
P6.4 In ∑ F = m , both m and r are unknown but remain constant.
r
Symbolically, write
⎛ ⎞ m ⎛ m⎞
∑ Fslow = ⎜⎝ ⎟⎠ ( 14.0 m s ) and ∑ Ffast = ⎜ ⎟ ( 18.0 m s )
2 2
r ⎝r⎠
Therefore, ∑ F is proportional to v2 and increases by a factor of

2
⎛ 18.0 ⎞ as v increases from 14.0 m/s to 18.0 m/s. The total force at the
⎜⎝ ⎟
14.0 ⎠
higher speed is then
2 2
⎛ 18.0 ⎞ ⎛ 18.0 ⎞
∑ Ffast = ⎜⎝ ⎟⎠ ∑ Fslow = ⎜⎝ ⎟ ( 130 N ) = 215 N
14.0 14.0 ⎠
This force must be horizontally inward to produce the driver’s

centripetal acceleration.
P6.5 We neglecting relativistic effects. With 1 u = 1.661 x 10–27 kg, and from
Newton’s second law, we obtain
mv 2
F = mac =
r
( 2.998 × 10 m s)
7 2
= ( 2 × 1.661 × 10 −27
kg )
( 0.480 m )
= 6.22 × 10−12 N
P6.6 (a) The car’s speed around the curve is found from
235 m
v= = 6.53 m s
36.0 s
This is the answer to part (b) of this problem. We calculate the
1
radius of the curve from ( 2π r ) = 235 m, which gives r = 150 m.
4
The car’s acceleration at point B is then

 ⎛ v2 ⎞
a r = ⎜ ⎟ toward the center
⎝ r ⎠
=
( 6.53 m s )
2
at 35.0° north of west

150 m
( ( )
= ( 0.285 m s 2 ) cos 35.0° − î + sin 35.0° ĵ )
= ( −0.233î + 0.163 ĵ) m s 2
(b) From part (a), v = 6.53 m s
(c) We find the average acceleration from

a avg =
 
v f − vi( )
Δt
=
(6.53 ĵ − 6.53î ) m s
36.0 s
= ( −0.181î + 0.181ĵ) m s 2
P6.7 Standing on the inner surface of the rim, and moving with it, each
person will feel a normal force exerted by the rim. This inward force
causes the 3.00 m/s2 centripetal acceleration:
ac = v 2 /r so v = ac r = ( 3.00 m s )(60.0 m ) = 13.4 m s

2
2π r
The period of rotation comes from v = :
T
2π r 2π ( 60.0 m )
T= = = 28.1 s
v 13.4 m s
so the frequency of rotation is
1 1 ⎛ 1 ⎞ ⎛ 60 s ⎞
f= = =⎜ ⎟⎜ ⎟ = 2.14 rev min
T 28.1 s ⎝ 28.1 s ⎠ ⎝ 1 min ⎠
P6.8 ANS. FIG. P6.8 shows the free-body diagram for this problem.
(a) The forces acting on the pendulum in the vertical direction must
be in balance since the acceleration of the bob in this direction is
zero. From Newton’s second law in the y direction,
∑F y = T cosθ − mg = 0
Chapter 6 289
Solving for the tension T gives
mg ( 80.0 kg ) ( 9.80 m s 2 )
T= = = 787 N
cosθ cos 5.00°
In vector form,

T = T sin θ î + T cosθ ĵ
= ( 68.6 N ) î + ( 784 N ) ĵ
ANS. FIG. P6.8
(b) From Newton’s second law in the x direction,
∑F x = T sin θ = mac
which gives
T sin θ ( 787 N ) sin 5.00°
ac = = = 0.857 m/s 2
m 80.0 kg
toward the center of the circle.
The length of the wire is unnecessary information. We could, on
the other hand, use it to find the radius of the circle, the speed of
the bob, and the period of the motion.
P6.9 ANS. FIG. P6.9 shows the constant
maximum speed of the turntable and the
centripetal acceleration of the coin.
(a) The force of static friction causes

the centripetal acceleration.
(b) From ANS. FIG. P6.9,
maî = f î + nĵ + mg − ĵ ( )
∑ Fy = 0 = n − mg
thus, n = mg and
v2
∑ r
F = m = f = µn = µmg
r
ANS. FIG. P6.9
Then,
µ=
v2
=
( 50.0 cm s ) = 0.085 0
2
rg ( 30.0 cm )( 980 cm s 2 )
P6.10 We solve for the tensions in the two strings:

Fg = mg = ( 4.00 kg ) ( 9.80 m s 2 ) = 39.2 N
The angle θ is given by

⎛ 1.50 m ⎞
θ = sin −1 ⎜ = 48.6°
⎝ 2.00 m ⎟⎠
The radius of the circle is then
r = ( 2.00 m ) cos 48.6° = 1.32 m
Applying Newton’s second law,
ANS. FIG. P6.10
2
mv
∑ Fx = max =
r
T cos 48.6° + T cos 48.6° =

( 4.00 kg ) ( 3.00 m/s )
2
a b
1.32 m
27.27 N
Ta + Tb = = 41.2 N [1]
cos 48.6°
∑ Fy = may : Ta sin 48.6° − Tb sin 48.6° − 39.2 N = 0
39.2 N
Ta − Tb = = 52.3 N
sin 48.6° [2]
To solve simultaneously, we add the equations in Ta and Tb:
(Ta + Tb) + (Ta – Tb) = 41.2 N + 52.3 N
93.8 N
Ta = = 46.9 N
2
This means that Tb = 41.2 N – Ta = –5.7 N, which we may interpret as
meaning the lower string pushes rather than pulls!
The situation is impossible because the speed of the object is too
small, requiring that the lower string act like a rod and push rather
than like a string and pull.
To answer the What if?, we go back to equation [2] above and

substitute mg for the weight of the object. Then,
∑ Fy = may : Ta sin 48.6° − Tb sin 48.6° − mg = 0
(4.00 kg)g
Ta − Tb = = 5.33g
sin 48.6°
Chapter 6 291
We then add this equation to equation [2] to obtain

(Ta + Tb) + (Ta – Tb) = 41.2 N + 5.33g
or Ta = 20.6 N + 2.67 g and Tb = 41.2 N − Ta = 41.2 N − 2.67 g
For this situation to be possible, Tb must be > 0, or g < 7.72 m/s2. This is
certainly the case on the surface of the Moon and on Mars.
P6.11 Call the mass of the egg crate m. The forces on it
are its weight Fg = mg vertically down, the
normal force n of the truck bed vertically up,
and static friction fs directed to oppose relative
sliding motion of the crate on the truck bed. The
friction force is directed radially inward. It is
the only horizontal force on the crate, so it
must provide the centripetal acceleration. ANS. FIG. P6.11
When the truck has maximum speed, friction fs
will have its maximum value with fs = µ s n.
Newton’s second law in component form becomes
∑ Fy = may giving n – mg = 0 or n = mg
∑ Fx = max giving fs = mar

From these three equations,
mv 2 mv 2
µsn ≤ and µ s mg ≤
r r
The mass divides out. The maximum speed is then
v ≤ µ s rg = 0.600 ( 35.0 m ) ( 9.80 m/s 2 ) → v ≤ 14.3 m/s
Section 6.2 Nonuniform Circular Motion

P6.12 (a) The external forces acting on the water are
the gravitational force
and the contact force exerted on the water by the pail .
(b) The contact force exerted by the pail is the most important in
causing the water to move in a circle. If the gravitational force
acted alone, the water would follow the parabolic path of a
projectile.
(c) When the pail is inverted at the top of the circular path, it cannot
hold the water up to prevent it from falling out. If the water is not
to spill, the pail must be moving fast enough that the required
centripetal force is at least as large as the gravitational force. That
is, we must have
v2
m ≥ mg or v ≥ rg = (1.00 m )( 9.80 m s2 ) = 3.13 m s
r
(d) If the pail were to suddenly disappear when it is at the top of the
circle and moving at 3.13 m/s, the water would follow the
parabolic path of a projectile launched with initial velocity
components of vxi = 3.13 m/s, vyi = 0.
P6.13 (a) The hawk’s centripetal acceleration is
v 2 ( 4.00 m s )
2
ac = = = 1.33 m s 2
r 12.0 m
(b) The magnitude of the acceleration vector is
ANS. FIG. P6.13
a = ac2 + at2
= (1.33 m/s ) + (1.20 m/s )

2 2 2 2
= 1.79 m/s 2
at an angle
⎛ ac ⎞
−1 −1 ⎛ 1.33 m/s ⎞
2
θ = tan ⎜ ⎟ = tan ⎜ = 48.0° inward
⎝a ⎠ t⎝ 1.20 m/s 2 ⎟⎠
6.14 We first draw a force diagram that shows
the forces acting on the child-seat system
and apply Newton’s second law to solve
the problem. The child’s path is an arc of a
circle, since the top ends of the chains are
fixed. Then at the lowest point the child’s
motion is changing in direction: He moves
with centripetal acceleration even as his
speed is not changing and his tangential
acceleration is zero.
ANS. FIG. P6.14
(a) ANS. FIG. P6.14 shows that the only
forces acting on the system of child + seat are the tensions in the
two chains and the weight of the boy:
mv 2
∑ F = Fnet = 2T − mg = ma = r
Chapter 6 293
with
Fnet = 2T − mg = 2 ( 350 N ) − ( 40.0 kg ) ( 9.80 m/s 2 ) = 308 N
solving for v gives
Fnet r (308 N)(3.00 m)
v= = = 4.81 m/s
m 40.0 kg
(b) The normal force from the seat on the child accelerates the child
in the same way that the total tension in the chain accelerates the
child-seat system. Therefore, n = 2T = 700 N .
P6.15 See the forces acting on seat (child) in ANS. FIG. P6.14.
Mv 2
(a) ∑ F = 2T − Mg =
R
⎛ R⎞
v 2 = ( 2T − Mg ) ⎜ ⎟
⎝ M⎠
R
v= ( 2T − Mg ) ⎛⎜⎝ M ⎞⎟⎠
Mv 2
(b) n − Mg = F =
R
Mv 2
n = Mg +
R
P6.16 (a) We apply Newton’s second law at
point A, with v = 20.0 m/s,
n = force of track on roller coaster,
and R = 10.0 m:
Mv 2
∑F = = n − Mg ANS. FIG. P6.16
R
From this we find
Mv 2 ( 500 kg )( 20.0 m s2 )
n = Mg + = ( 500 kg ) ( 9.80 m s ) +
2
R 10.0 m
n = 4 900 N + 20 000 N = 2.49 × 10 N 4
(b) At point B, the centripetal acceleration is now downward, and

Newton’s second law now gives
Mv 2
∑ F = n − Mg = −
R
The maximum speed at B corresponds to the case where the

rollercoaster begins to fly off the track, or when n = 0. Then,
2
Mvmax
−Mg = −
R
which gives
vmax = Rg = ( 15.0 m )( 9.80 m/s 2 ) = 12.1 m/s
v2
P6.17 (a) ac =
r
r=
v2
=
(13.0 m s ) = 8.62 m 2
ac 2 ( 9.80 m s 2 )
(b) Let n be the force exerted by the rail. ANS. FIG. P6.17
Newton’s second law gives

Mv 2
Mg + n =
r
⎛ v2 ⎞
n = M ⎜ − g ⎟ = M ( 2g − g ) = Mg, downward
⎝ r ⎠
(c) ac =
v2
, or ac =
(13.0 m s ) = 8.45 m s2 2
r 20.0 m
(d) If the force exerted by the rail is n1,
Mv 2
then n1 + Mg = = Mac
r
n1 = M ( ac − g ) which is < 0 since ac = 8.45 m/s
2
Thus, the normal force would have to point away from the
center of the curve. Unless they have belts, the riders will fall
from the cars.
In a teardrop-shaped loop, the radius of curvature r decreases,

causing the centripetal acceleration to increase. The speed
would decrease as the car rises (because of gravity), but the
overall effect is that the required centripetal force increases,
meaning the normal force increases--there is less danger if
not wearing a seatbelt.
Chapter 6 295
P6.18 (a) Consider radial forces on the object, taking inward as positive.
mv 2
∑ Fr = mar : T − mg cosθ =
r
Solving for the tension gives
mv 2
T = mg cosθ +
r
= (0.500 kg)(9.80 m/s 2 )cos 20.0°
+ (0.500 kg)(8.00 m/s)2 /2.00 m
= 4.60 N + 16.0 N = 20.6 N
(b) We already found the radial component of acceleration,
v 2 ( 8.00 m/s )
2
ar = = = 32.0 m/s 2 inward

r 2.00 m
Consider the tangential forces on the object:
∑ Ft = mat : mg sin θ = mat
Solving for the tangential component of acceleration gives
at = g sin θ = ( 9.80 m/s 2 ) sin 20.0°
= 3.35 m/s 2 downward tangent to the circle
(c) The magnitude of the acceleration is
a = ar2 + at2 = ( 32.0 m/s ) + ( 3.35 m/s )

2 2 2 2
= 32.2 m/s 2
at an angle of
⎛ 3.35 m/s 2 ⎞
tan −1 ⎜ = 5.98°
⎝ 32.0 m/s 2 ⎟⎠
Thus, the acceleration is
32.2 m/s 2 inward and below the cord at 5.98°
(d) No change.
(e) If the object is swinging down it is gaining speed, and if the object
is swinging up it is losing speed, but the forces are the same;
therefore, its acceleration is regardless of the direction of swing.
P6.19 Let the tension at the lowest point be T. From

Newton’s second law, ∑ F = ma and
mv 2
T − mg = mac =
r
⎛ v2 ⎞
T = m⎜ g + ⎟
⎝ r ⎠
⎡
T = ( 85.0 kg ) ⎢ 9.80 m s +
2 ( 8.00 m s ) ⎤
2
⎥
⎢⎣ 10.0 m ⎥⎦ ANS. FIG. P6.19
= 1.38 kN > 1 000 N
He doesn’t make it across the river because the vine breaks.
Section 6.3 Motion in Accelerated Frames

P6.20 (a) From ∑ Fx = Ma, we obtain
T 18.0 N
a= = = 3.60 m s 2 to the right
M 5.00 kg
(b) If v = const, a = 0, so T = 0 . (This is also an equilibrium

situation.)
(c) Someone in the car (noninertial observer) claims that the forces
on the mass along x are T and a fictitious force (– Ma).
(d) Someone at rest outside the car (inertial observer) claims that T
is the only force on M in the x direction.
ANS. FIG. P6.20
Chapter 6 297
P6.21 The only forces acting on the suspended object are the

force of gravity mg and the force of tension T forward
and upward at angle θ with the vertical, as shown in
the free-body diagram in ANS. FIG. P6.21. Applying
Newton’s second law in the x and y directions,
∑ Fx = T sin θ = ma [1]
∑ Fy = T cosθ − mg = 0
or T cos θ = mg [2] ANS. FIG. P6.21
(a) Dividing equation [1] by [2] gives
a 3.00 m s 2
tan θ = = = 0.306
g 9.80 m s 2
Solving for θ , θ = 17.0°
(b) From equation [1],
T=
ma ( 0.500 kg ) 3.00 m s
=
2
(
= 5.12 N
)
sin θ sin ( 17.0° )
P6.22 In an inertial reference frame, the girl is accelerating horizontally
inward at
v 2 ( 5.70 m s )
2
= = 13.5 m s 2
r 2.40 m
In her own noninertial frame, her head feels a horizontally outward
fictitious force equal to its mass times this acceleration. Together this
force and the weight of her head add to have a magnitude equal to the
mass of her head times an acceleration of
2
⎛ v2 ⎞
g +⎜ ⎟ =
2
⎝ r ⎠
( 9.80 m/s ) + (13.5 m/s )
2 2 2 2
= 16.7 m s 2
16.7 m/s
This is larger than g by a factor of = 1.71 .
9.80 m/s
Thus, the force required to lift her head is larger by this factor, or the
required force is
F = 1.71( 55.0 N ) = 93.8 N
P6.23 The scale reads the upward normal force exerted by the floor on the
passenger. The maximum force occurs during upward acceleration
(when starting an upward trip or ending a downward trip). The
minimum normal force occurs with downward acceleration. For each
respective situation,
∑ Fy = may becomes for starting +591 N − mg = +ma
and for stopping +391 N − mg = −ma
where a represents the magnitude of the acceleration.
(a) These two simultaneous equations can be added to eliminate a
and solve for mg:
+ 591 N − mg + 391 N − mg = 0
or 982 N – 2mg = 0
982 N
Fg = mg = = 491 N
2
Fg 491 N
(b) From the definition of weight, m = = = 50.1 kg
g 9.80 m s 2
(c) Substituting back gives +591 N − 491 N = (50.1 kg)a, or
100 N
a= = 2.00 m/s 2
50.1 kg
P6.24 Consider forces on the backpack as it slides in the Earth frame of
reference.
∑ Fy = may : +n − mg = ma, n = m ( g + a ) , f k = µk m ( g + a )
∑ Fx = max : − µk m ( g + a ) = max
The motion across the floor is described by
1 2 1
L = vt + axt = vt − µ k ( g + a ) t 2
2 2
We solve for µ k :
1
vt − L = µk ( g + a ) t 2
2
2 ( vt − L )
µk =
( g + a)t2
P6.25 The water moves at speed
2π r 2π ( 0.120 m )
v= = = 0.104 m s
T 7.25 s
Chapter 6 299
The top layer of water feels a downward force of gravity mg and an

outward fictitious force in the turntable frame of reference,
mv 2 m ( 0.104 m s )
2
= = m 9.01 × 10−2 m s 2
r 0.12 m
It behaves as if it were stationary in a gravity field pointing downward
and outward at
⎛ 0.090 1 m s 2 ⎞
tan −1 ⎜ = 0.527°
⎝ 9.8 m s ⎟⎠
2
Its surface slopes upward toward the outside, making this angle with
the horizontal.
Section 6.4 Motion in the Presence of

Velocity-Dependent Resistive Forces
m 1
P6.26 (a) ρ= , A = 0.020 1 m2, R = ρair ADvT2 = mg
V 2
⎡4 3⎤
m = ρ beadV = 0.830 g cm 3 ⎢ π ( 8.00 cm ) ⎥ = 1.78 kg
⎣3 ⎦
Assuming a drag coefficient of D = 0.500 for this spherical object,
and taking the density of air at 20°C from the endpapers, we have
2 ( 1.78 kg ) ( 9.80 m s 2 )
vT = = 53.8 m s
0.500 ( 1.20 kg m 3 ) ( 0.020 1 m 2 )
(b) From v 2f = vi2 + 2gh = 0 + 2gh, we solve for h:
h=
v 2f
=
( 53.8 m s )2 = 148 m
2g 2 ( 9.80 m s 2 )
P6.27 With 100 km/h = 27.8 m/s, the resistive force is

1 1
Dρ Av 2 = ( 0.250 )( 1.20 kg m 3 ) ( 2.20 m 2 ) ( 27.8 m s )
2
R=
2 2
= 255 N
R 255 N
a=− =− = −0.212 m s 2
m 1 200 kg
P6.28 Given m = 80.0 kg, vT = 50.0 m/s, we write
Dρ AvT2
mg =
2
which gives
Dρ A mg
= 2 = 0.314 kg m
2 vT
(a) At v = 30.0 m/s,
a= g−
Dρ Av 2 2
= 9.80 m/s 2 −
( 0.314 kg/m )( 30.0 m/s ) 2
m 80.0 kg
= 6.27 m/s 2 downward
(b) At v = 50.0 m/s, terminal velocity has been reached.

∑ Fy = 0 = mg − R
⇒ R = mg = ( 80.0 kg ) ( 9.80 m s 2 ) = 784 N directed up
(c) At v = 30.0 m/s,

Dρ Av 2
= ( 0.314 kg/m ) ( 30.0 m/s ) = 283 N upward
2
2
P6.29 Since the upward velocity is constant, the resultant force on the ball is
zero. Thus, the upward applied force equals the sum of the
gravitational and drag forces (both downward):
F = mg + bv
The mass of the copper ball is
4πρ r 3 ⎛ 4 ⎞
= ⎜ ⎟ π ( 8.92 × 103 kg m 3 ) ( 2.00 × 10−2 m )
3
m=
3 ⎝ 3⎠
= 0.299 kg
The applied force is then
F = mg + bv = ( 0.299 kg ) ( 9.80 m/s 2 )
+ ( 0.950 kg/s ) ( 9.00 × 10−2 m/s )
= 3.01 N
P6.30 (a) The acceleration of the Styrofoam is given by

a = g – Bv
Chapter 6 301
g
When v = vT, a = 0 and g = BvT → B =
vT
The Styrofoam falls 1.50 m at constant speed vT in 5.00 s.
Thus,
h 1.50 m
vT = = = 0.300 m/s
Δt 5.00 s
Then
g 9.80 m/s 2
B= = = 32.7 s −1
vT 0.300 m/s
(b) At t = 0, v = 0, and a = g = 9.80 m s 2 down
(c) When v = 0.150 m/s,

a = g − Bv
= 9.80 m/s 2 − ( 32.7 s −1 ) ( 0.150 m/s )
= 4.90 m/s 2 down

P6.31 We have a particle under a net force in the special case of a resistive
force proportional to speed, and also under the influence of the
gravitational force.
(a) The speed v varies with time according to Equation 6.6,
mg
v=
b ( )
1 – e –bt/m = vT 1 – e –t/τ ( )
where vT = mg/b is the terminal speed. Hence,
mg ( 3.00 × 10 kg ) ( 9.80 m s )
−3 2
b= = = 1.47 N ⋅ s m
vT 2.00 × 10−2 m s
(b) To find the time interval for v to reach 0.632vT, we substitute
v = 0.632vT into Equation 6.6, giving
0.632vT = vT (1 − e−bt/m) or 0.368 = e−(1.47t/0.003 00)

Solve for t by taking the natural logarithm of each side of the
equation:
1.47 t 1.47 t
ln(0.368) = – or –1 = –
3.00 × 10 –3 3.00 × 10 –3
⎛ m⎞
or t = − ⎜ ⎟ ln ( 0.368 ) = 2.04 × 10−3 s
⎝ b⎠
(c) At terminal speed, R = vTb = mg. Therefore,
R = vT b = mg = ( 3.00 × 10−3 kg ) ( 9.80 m/s 2 ) = 2.94 × 10−2 N

P6.32 We write
1
−kmv 2 = − Dρ Av 2
2
so
Dρ A 0.305 ( 1.20 kg m ) ( 4.2 × 10 m )

3 −3 2
k= = = 5.3 × 10−3 m
2m 2 ( 0.145 kg )
solving for the velocity as the ball crosses home plate gives
v = vi e − kx = ( 40.2 m s ) e (
− 5.3×10−3 m )( 18.3 m )
= 36.5 m s
P6.33 We start with Newton’s second law,

∑ F = ma
substituting,
dv
−kmv 2 = m
dt
dv
−kdt =
v2
t v
−k ∫ dt = ∫ v −2 dv
0 vi
integrating both sides gives

v
v −1 1 1
−k ( t − 0 ) = =− +
−1 vi
v vi
1 1 1 + vi kt
= + kt =
v vi vi
vi
v=
1 + vi kt
Chapter 6 303
P6.34 (a) Since the window is vertical, the normal force is horizontal and is
given by n = 4.00 N. To find the vertical component of the force,
we note that the force of kinetic friction is given by
fk = µkn = 0.900(4.00 N) = 3.60 N upward
to oppose downward motion. Newton’s second law then becomes
∑ Fy = may : +3.6 N − (0.16 kg)(9.8 m/s 2 ) + Py = 0
Py = −2.03 N = 2.03 N down
(b) Now, with the increased downward force, Newton’s second law
gives
∑ Fy = may :
+ 3.60 N − (0.160 kg)(9.80 m/s 2 ) − 1.25(2.03 N)
= 0.160 kg ay
then
ay = −0.508 N/0.16 kg = −3.18 m/s 2 = 3.18 m/s 2 down
(c) At terminal velocity,

∑ Fy = may : + (20.0 N ⋅ s/m)vT − (0.160 kg)(9.80 m/s 2 )
− 1.25(2.03 N) = 0
Solving for the terminal velocity gives
vT = 4.11 N/(20 N ⋅ s/m) = 0.205 m/s down
P6.35 (a) We must fit the equation v = vie−ct to the two data points:
At t = 0, v = 10.0 m/s, so v = vie−ct becomes
10.0 m/s = vi e0 = (vi)(1)

which gives vi = 10.0 m/s
At t = 20.0 s, v = 5.00 m/s so the equation becomes
5.00 m/s = (10.0 m/s)e−c(20.0 s)
giving 0.500 = e−c(20.0 s)
⎛ 1⎞ ln ( 2 ) 1
or −20.0c = ln ⎜ ⎟ → c = − = 3.47 × 10−2 s −1
⎝ 2⎠ 20.0
(b) At t = 40.0 s
v = ( 10.0 m s ) e −40.0c = ( 10.0 m s ) ( 0.250 ) = 2.50 m s
(c) The acceleration is the rate of change of the velocity:

dv d
a= = v e – ct = vi ( e – ct ) (–c) = – c ( vi e – ct )
dt dt i
= –cv
Thus, the acceleration is a negative constant times the speed.
1
P6.36 In R = Dρ Av 2 , we estimate that the coefficient of drag for an open
2
palm is D = 1.00, the density of air is ρ = 1.20 kg m 3 , the area of an
open palm is A = ( 0.100 m ) ( 0.160 m ) = 1.60 × 10−2 m 2 , and v = 29.0 m/s
(65 miles per hour). The resistance force is then
1
R = ( 1.00 )( 1.20 kg m 3 ) ( 1.60 × 10−2 m 2 ) ( 29.0 m s ) = 8.07 N
2
2
or R ~ 101 N
Additional Problems
P6.37 Because the car travels at a constant speed, it has no tangential
acceleration, but it does have centripetal acceleration because it travels
along a circular arc. The direction of the centripetal acceleration is
toward the center of curvature, and the direction of velocity is tangent
to the curve.
Point A
direction of velocity: East
direction of the centripetal acceleration: South

Point B
direction of velocity: South
direction of the centripetal acceleration: West

P6.38 The free-body diagram of the passenger is shown in
ANS. FIG. P6.38. From Newton’s second law,
∑ Fy = may
mv 2
n − mg =
r
ANS. FIG. P6.38
Chapter 6 305
which gives
mv 2
n = mg +
r
= (50 kg)(9.80 m s ) +
( 50.0 kg ) ( 19 m s )
2
2
25 m
= 1.2 × 103 N
P6.39 The free-body diagram of the rock is
shown in ANS. FIG. P6.39. Take the
x direction inward toward the center
of the circle. The mass of the rock
does not change. We know when
r1 = 2.50 m, v1 = 20.4 m/s, and
T1 = 50.0 N. To find T2 when
r2 = 1.00 m, and v2 = 51.0 m/s, we
use Newton’s second law in the
horizontal direction: ANS. FIG. P6.39
∑ Fx = max
In both cases,
mv12 mv22
T1 = and T2 =
r1 r2
Taking the ratio of the two tensions gives
2
T2 v22 r1 ⎛ 51.0 m/s ⎞ ⎛ 2.50 m ⎞
= =⎜ ⎜ = 15.6
⎟
T1 v12 r2 ⎝ 20.4 m/s ⎠ ⎝ 1.00 m ⎟⎠
then
T2 = 15.6T1 = 15.6 ( 50.0 N ) = 781 N
We assume the tension in the string is not altered by friction from the
hole in the table.
P6.40 (a) We first convert the speed of the car to SI units:
⎛ 1 h ⎞ ⎛ 1 000 m ⎞
v = ( 30 km h ) ⎜ ⎜ ⎟
⎝ 3 600 s ⎟⎠ ⎝ 1 km ⎠
= 8.33 m s
ANS. FIG. P6.40
Newton’s second law in the vertical direction
then gives
mv 2
∑ Fy = may : + n − mg = −
r
Solving for the normal force,

⎛ v2 ⎞
n = m⎜ g − ⎟
⎝ r ⎠
⎡
= ( 1 800 kg ) ⎢ 9.80 m/s −
2 ( 8.33 m/s ) ⎤
2
⎥
⎣ 20.4 m ⎦
= 1.15 × 10 4 N up
(b) At the maximum speed, the weight of the car is just enough to
mv 2
provide the centripetal force, so n = 0. Then mg = and
r
v= gr = ( 9.80 m/s )( 20.4 m ) =

2
14.1 m/s = 50.9 km/h
P6.41 (a) The free-body diagram in ANS. FIG. P6.40 shows the forces on
the car in the vertical direction. Newton’s second law then gives
mv 2
∑ Fy = may =
R
mv 2 mv 2
mg − n = n = mg −
R R
mv 2
(b) When n = 0, mg =
R
Then, v = gR
A more gently curved bump, with larger radius, allows the car to
have a higher speed without leaving the road. This speed is
proportional to the square root of the radius.
P6.42 The free-body diagram for the object is
shown in ANS. FIG. P6.42. The object travels
in a circle of radius r = L cos θ about the
vertical rod.
Taking inward toward the center of the circle
as the positive x direction, we have
mv 2
∑ Fx = max : n sin θ =
r
∑ Fy = may :
ANS. FIG. P6.42
n cos θ − mg = 0 → n cos θ = mg
Chapter 6 307
Dividing, we find
n sin θ mv 2 /r v2
= → tan θ =
n cos θ gr gr
Solving for v gives
v 2 = gr tan θ
v 2 = g(L cos θ )tan θ
v = (gL sin θ )1/2
P6.43 Let vi represent the speed of the object at time 0. We have

v dv b t v b t
∫v v = − m ∫i dt
i
ln v v = −
i
t
m i
b bt
ln v − ln vi = − (t − 0) ln ( v / vi ) = −
m m
v / vi = e −bt/m v = vi e −bt/m
From its original value, the speed decreases rapidly at first and then
more and more slowly, asymptotically approaching zero.
In this model the object keeps losing speed forever. It travels a
finite distance in stopping.
The distance it travels is given by

r t −bt/m
∫0 dr = vi ∫0 e dt
m t −bt/m ⎛ b ⎞ m −bt/m t
r=− vi ∫0 e ⎜⎝ − dt ⎟⎠ = − vi e
b m b 0
m mvi
= − vi ( e −bt/m − 1) = (1 − e −bt/m )
b b
mvi
As t goes to infinity, the distance approaches (1 − 0) = mvi b.
b
P6.44 The radius of the path of object 1 is twice that of
object 2. Because the strings are always “collinear,”
both objects take the same time interval to travel
around their respective circles; therefore, the speed
of object 1 is twice that of object 2.
The free-body diagrams are shown in ANS. FIG.
P6.44. We are given m1 = 4.00 kg, m2 = 3.00 kg,
v = 4.00 m/s, and  = 0.500 m.
ANS. FIG. P6.44
Taking down as the positive direction, we have

m1 v12
Object 1: T1 + m1 g = , where v1 = 2v, r1 = 2.
r1
m2 v22
Object 2: T2 − T1 + m2 g = , where v2 = v, r2 = 2.
r2
(a) From above:
m1 v12 ⎛v2 ⎞
T1 = − m1 g = m1 ⎜ 1 − g ⎟
r1 ⎝ r1 ⎠
⎡ [ 2 ( 4.00 m/s )]2 ⎤

T1 = ( 4.00 kg ) ⎢ − 9.80 m/s 2 ⎥
⎢⎣ 2 ( 0.500 m ) ⎥⎦
T1 = 216.8 N = 217 N
(b) From above:

m2 v22
T2 = T1 + − m2 g
r2
⎛v 2 ⎞
T2 = T1 + m2 ⎜ 2 − g ⎟
⎝ r2 ⎠
⎡ ( 4.00 m/s )2 ⎤
T2 = T1 + ( 3.00 kg ) ⎢ − 9.80 m/s 2 ⎥
⎣ 0.500 m ⎦
T2 = 216.8 N + 66.6 N = 283.4 N = 283 N
(c) From above, T2 > T1 always, so string 2 will break first.
P6.45 (a) At each point on the vertical circular path,

two forces are acting on the ball (see ANS.
FIG. P6.45):
(1) The downward gravitational force
with constant magnitude Fg = mg
(2) The tension force in the string,

always directed toward the
center of the path ANS. FIG. P6.45
Chapter 6 309
(b) ANS. FIG. P6.45 shows the forces acting on the ball when it is at
the highest point on the path (left-hand diagram) and when it is
at the bottom of the circular path (right-hand diagram). Note that
the gravitational force has the same magnitude and direction at
each point on the circular path. The tension force varies in
magnitude at different points and is always directed toward the
center of the path.
(c) At the top of the circle, Fc = mv2/r = T + Fg, or
mv 2 mv 2 ⎛ v2 ⎞
T= − Fg = − mg = m ⎜ − g ⎟
r r ⎝ r ⎠
⎡ ( 5.20 m s )2 ⎤
= ( 0.275 kg ) ⎢ − 9.80 m s 2 ⎥ = 6.05 N
⎢⎣ 0.850 m ⎥⎦
(d) At the bottom of the circle, Fc = mv2/r = T – Fg = T – mg, and

solving for the speed gives
r ⎛T ⎞ ⎛T ⎞
v2 =
m
( T − mg ) = r ⎜ − g ⎟
⎝m ⎠
and v = r ⎜ − g⎟
⎝m ⎠
If the string is at the breaking point at the bottom of the circle,

then T = 22.5 N, and the speed of the object at this point must be
⎛ 22.5 N ⎞
v= ( 0.850 m ) ⎜ − 9.80 m s 2 ⎟ = 7.82 m s
⎝ 0.275 kg ⎠
P6.46 The free-body diagram is shown on the

right, where it is assumed that friction
points up the incline, otherwise, the child
would slide down the incline. The net force
is directed left toward the center of the
circular path in which the child travels. The
radius of this path is R = d cosθ .
Three forces act on the child, a normal
force, static friction, and gravity. The ANS. FIG. P6.46
relations of their force components are:
∑ Fx : f s cos θ − n sin θ = mv 2 /R [1]
∑ Fy : f s sin θ + n cos θ − mg = 0 →
f s sin θ + n cos θ = mg [2]
Solve for the static friction and normal force.
To solve for static friction, multiply equation [1] by cos θ and equation
[2] by sin θ and add:
cosθ [ f s cosθ − nsin θ ] + sin θ [ f s sin θ − ncosθ ]
⎛ mv 2 ⎞
= cosθ ⎜ + sin θ ( mg )
⎝ R ⎟⎠
⎛ mv 2 ⎞
f s = mg sin θ + ⎜ cosθ
⎝ R ⎟⎠
To solve for the normal force, multiply equation [1] by –sin θ and
equation [2] by cos θ and add:
− sin θ [ f s cosθ − nsin θ ] + cosθ [ f s sin θ − ncosθ ]
⎛ mv 2 ⎞
= − sin θ ⎜ + cosθ ( mg )
⎝ R ⎟⎠
⎛ mv 2 ⎞
n = mg cosθ − ⎜ sin θ
⎝ R ⎟⎠
In the above, we have used sin 2 θ + cos 2 θ = 1.
If the above equations are to be consistent, static friction and the
normal force must satisfy the condition fs ≤ µsn; this means
(mg) sin θ + (mv 2 R)cos θ ≤ µ s [(mg) cos θ − (mv 2 R)sin θ ] →
v 2 (cos θ + µ s sin θ ) ≤ g R( µ s cos θ − sin θ )
Using this result, and that R = d cos θ, we have the requirement that
gd cos θ ( µ s cos θ − sin θ )
v≤
(cos θ + µ s sin θ )
If this condition cannot be met, if v is too large, the physical situation
cannot exist.
The values given in the problem are d = 5.32 m, µs = 0.700, θ = 20.0°,
and v = 3.75 m/s. Check whether the given value of v satisfies the
above condition:
( 9.80 m/s )( 5.32 m ) cos 20.0°[( 0.700) cos 20.0° − sin 20.0°]
2
( cos 20.0° + 0.700 sin 20.0°)

= 3.62 m/s
The situation is impossible because the speed of the child given
in the problem is too large: static friction could not keep the child
in place on the incline.
Chapter 6 311
P6.47 (a) The speed of the bag is

2π ( 7.46 m )
= 1.23 m s
38 s
The total force on it must add to
mv 2 ANS. FIG. P6.47
mac =
r
=
( 30 kg ) ( 1.23 m s )
2
= 6.12 N
7.46 m
Newton’s second law gives
∑ Fx = max : f s cos 20.0° − nsin 20.0° = 6.12 N
∑ Fy = may : f s sin 20.0° + ncos 20.0°
− ( 30.0 kg ) ( 9.80 m s 2 ) = 0
Solving for the normal force gives
f s cos 20.0° − 6.12 N
n=
sin 20.0°
Substituting,
cos 2 20.0° cos 20.0°
f s sin 20.0° + f s − ( 6.12 N ) = 294 N
sin 20.0° sin 20.0°
f s ( 2.92 ) = 294 N + 16.8 N
f s = 106 N
(b) The speed of the bag is now
2π ( 7.94 m )
v= = 1.47 m s
34 s
which corresponds to a total force of
mv 2
mac =
r
=
( 30 kg )(1.47 m s)
2
= 8.13 N
7.94 m
Newton’s second law then gives
f s cos 20 − nsin 20 = 8.13 N
f s sin 20 + ncos 20 = 294 N
Solving for n,
f s cos 20.0° − 8.13 N
n=
sin 20.0°
Substituting,
cos 2 20.0° cos 20.0°
f s sin 20.0° + f s − ( 8.13 N ) = 294 N
sin 20.0° sin 20.0°
f s ( 2.92 ) = 294 N + 22.4 N
f s = 108 N
( 108 N ) cos 20.0° − 8.13 N
n= = 273 N
sin 20.0°
f 108 N
µs = s = = 0.396
n 273 N
P6.48 When the cloth is at a lower
angle θ, the radial component
of ∑ F = ma reads
mv 2
n + mg sin θ =
r
At θ = 68.0°, the normal force ANS. FIG. P6.48
v2
drops to zero and g sin 68° = :
r
v = rg sin 68° = ( 0.33 m ) ( 9.8 m s 2 ) sin 68° = 1.73 m s
The rate of revolution is

⎛ 1 rev ⎞ ⎛ 2π r ⎞
angular speed = ( 1.73 m s ) ⎜ ⎟
⎝ 2π r ⎠ ⎜⎝ 2π ( 0.33 m ) ⎟⎠
= 0.835 rev s = 50.1 rev min
P6.49 The graph in Figure 6.16b is

shown in ANS. FIG. P6.49.
(a) The graph line is straight,
so we may use any two
points on it to find the
slope. It is convenient to
take the origin as one
point, and we read
(9.9 m2/s2, 0.16 N) as the
coordinates of another
point. Then the slope is ANS. FIG. P6.49
0.160 N − 0
slope = = 0.016 2 kg m
9.9 m 2 s 2
Chapter 6 313
1
(b) In R = Dρ Av 2 , we identify the vertical-axis variable as R and
2
the horizontal-axis variable as v2. Then the slope is
R 21 Dρ Av 2 1
slope = 2 = 2
= Dρ A
v v 2
(c) We follow the directions in the problem statement:
1
Dρ A = 0.0162 kg m
2
2 ( 0.0162 kg m )
D= = 0.778
(1.20 kg m 3 ) π ( 0.105 m )
2
(d) From the table, the eighth point is at force

mg = 8 ( 1.64 × 10−3 kg ) ( 9.80 m s 2 ) = 0.129 N
and horizontal coordinate (2.80 m/s)2. The vertical coordinate of

the line is here
( 0.016 2 kg m ) ( 2.80 m s ) = 0.127 N

2
The scatter percentage is

0.129 N − 0.127 N
= 1.5%
0.127 N
(e) The interpretation of the graph can be stated thus:
For stacked coffee filters falling at terminal speed, a graph
of air resistance force as a function of squared speed
demonstrates that the force is proportional to the speed
squared within the experimental uncertainty estimated
as 2%. This proportionality agrees with that described by
1
the theoretical equation R = Dρ Av 2 . The value of the
2
constant slope of the graph implies that the drag
coefficient for coffee filters is D = 0.78 ± 2%.
P6.50 (a) The forces acting on the ice cube are the Earth’s gravitational
force, straight down, and the basin’s normal force, upward and
inward at 35.0° with the vertical. We choose the x and y axes to be
horizontal and vertical, so that the acceleration is purely in the x
direction. Then
∑ Fx = max : n sin 35° = mv 2 /R
∑ Fy = may : n cos 35° − mg = 0
Dividing eliminates the normal force:
n sin 35.0° n cos 35.0° = mv 2 /Rmg
tan 35.0° = v2/Rg
v = Rg tan 35.0° = (6.86 m/s ) R 2
(b) The mass is unnecessary.
(c) The answer to (a) indicates that the speed is proportional to the
square root of the radius, so increasing the radius will make the
required speed increase.
(d) The period of revolution is given by

2π R 2π R
T=
v
=
Rg tan 35.0°
= 2.40 s/ m( ) R
When the radius increases, the period increases.
(e) On a larger circle, the ice cube’s speed is proportional to R but

the distance it travels is proportional to R, so the time interval
required is proportional to R R = R.
P6.51 Take the positive x axis up the hill. Newton’s second law in the x
direction then gives
∑ Fx = max : + T sin θ − mg sin φ = ma
from which we obtain
T
a= sin θ − g sin φ [1]
m
In the y direction,
∑ Fy = may : + T cosθ − mg cosφ = 0
Chapter 6 315
Solving for the tension gives

mg cosφ
T= [2]
cosθ
Substituting for T from [2] into [1] gives
g cosφ sin θ
a= − g sin φ
cosθ
a = g ( cosφ tan θ − sin φ )
P6.52 (a) We first convert miles per hour to feet per second:
⎛ 88.0 ft s ⎞
v = ( 300 mi h ) ⎜ = 440 ft s at the top of the loop
⎝ 60.0 mi h ⎟⎠
and v = 450 mi/h = 660 ft/s at the bottom of the loop.
At the lowest point, his seat exerts an upward force; therefore, his
weight seems to increase. His apparent weight is
⎛ 160 lb ⎞ ( 660 ft/s )

2
v2
Fg′ = mg + m = 160 lb + ⎜ = 1 975 lb
r ⎝ 32.0 ft/s 2 ⎟⎠ 1 200 ft
(b) At the highest point, the force of the seat on the pilot is directed
down and
⎛ 160 lb ⎞ ( 440 ft/s )

2
v2
Fg′ = mg − m = 160 lb − ⎜ = −647 lb
r ⎝ 32.0 ft/s 2 ⎟⎠ 1 200 ft
Since the plane is upside down, the seat exerts this downward
force as a normal force.
mv 2
(c) When Fg′ = 0, then mg = . If we vary the aircraft's R and v
R
such that this equation is satisfied, then the pilot feels weightless.
P6.53 (a) The only horizontal force on the car is the force of friction,
with a maximum value determined by the surface roughness
(described by the coefficient of static friction) and the normal
force (here equal to the gravitational force on the car).
(b) From Newton’s second law in one dimension,
f
∑ Fx = max : − f = ma → a = − = ( v 2 − v02 ) 2 ( x − x0 )
m
solving for the stopping distance gives
m ( v 2 − v02 ) (1 200 kg ) ⎡⎣ 02 − ( 20.0 m s )2 ⎤⎦

x − x0 = = = 34.3 m
2f 2 ( −7 000 N )
(c) Newton’s second law now gives
mv 2
f=
r
mv 2 ( 1 200 kg ) ( 20.0 m/s )

2
or r= = = 68.6 m
f 7 000 N
A top view shows that you can avoid running into the wall by
turning through a quarter-circle, if you start at least this far away
from the wall.
(d) Braking is better. You should not turn the wheel. If

you used any of the available friction force to change
the direction of the car, it would be unavailable to
slow the car, and the stopping distance would be
longer.
(e) The conclusion is true in general. The radius of the curve you
can barely make is twice your minimum stopping distance.
P6.54 (a) Since the object of mass m2 is in equilibrium, ∑ Fy = T − m2 g = 0
or T = m2 g .
(b) The tension in the string provides the required centripetal

acceleration of the puck.
Thus, Fc = T = m2 g .
m1 v 2
(c) From Fc = ,
R
RFc ⎛ m2 ⎞
we have v = = ⎜⎝ m ⎟⎠ gR
m1 1
Chapter 6 317
(d) The puck will spiral inward, gaining speed as it does so. It gains
speed because the extra-large string tension pulls at an angle of
less than 90° to the direction of the inward-spiraling velocity,
producing forward tangential acceleration as well as inward
radial acceleration of the puck.
(e) The puck will spiral outward, slowing down as it does so.
P6.55 (a) The gravitational force exerted by the

planet on the person is
mg = (75.0 kg)(9.80 m/s2)
= 735 N down
Let n represent the force exerted on the
person by a scale, which is an upward
force whose size is her “apparent
weight.” The true weight is mg down. ANS. FIG. P6.55
For the person at the equator, summing
up forces on the object in the direction towards the Earth’s center
gives ∑ F = ma:
mg − n = mac
where ac = v2/RE = 0.033 7 m/s2

is the centripetal acceleration directed toward the center of the
Earth.
Thus, we can solve part (c) before part (b) by noting that
n = m(g − ac) < mg
(c) or mg = n + mac > n.
The gravitational force is greater. The normal force is smaller,

just as one experiences at the top of a moving ferris wheel.
(b) If m = 75.0 kg and g = 9.80 m/s2, at the equator we have
n = m(g − ac) = (75.0 kg)(9.800 m/s2 – 0.033 7 m/s2) = 732 N

P6.56 (a) v = vi + kx implies the acceleration is
dv dx
a= = 0+k = +kv
dt dt
(b) The total force is

∑ F = ma = m ( +kv )
As a vector, the force is parallel or antiparallel to the velocity:
 
∑ F = kmv
(c) For k positive, some feedback mechanism could be used to
impose such a force on an object for a while. The object’s
speed rises exponentially.
(d) For k negative, think of a duck landing on a lake, where the

water exerts a resistive force on the duck proportional to its
speed.
P6.57 (a) As shown in the free-body diagram on the right, the mass at the
end of the chain is in vertical equilibrium. Thus,
T cos θ = mg [1]
Horizontally, the mass is accelerating
toward the center of a circle of radius r:
mv 2
T sin θ = mar = [2]
r
Here, r is the sum of the radius of the
circular platform R = D/2 = 4.00 m
and 2.50 sin θ :
r = ( 2.50sin θ + 4.00 ) m
r = ( 2.50sin 28.0° + 4.00 ) m
= 5.17 m
We solve for the tension T from [1]:
mg
T cos θ = mg → T =
cos θ
ANS. FIG. P6.57
and substitute into [2] to obtain
ar v 2
tan θ = =
g gr
v 2 = gr tan θ = ( 9.80 m/s 2 ) ( 5.17 m ) ( tan 28.0° )
v = 5.19 m/s
Chapter 6 319
(b) The free-body diagram for the child is shown in ANS. FIG. P6.57.
mg ( 40.0 kg )( 9.80 m s2 )
(c) T= = = 444 N
cos θ cos 28.0°
P6.58 (a) The putty, when dislodged, rises and returns to the original level
2v
in time t. To find t, we use vf = vi + at: i.e., –v = + v – gt or t = ,
g
where v is the speed of a point on the rim of the wheel.
2π R 2v 2π R
If R is the radius of the wheel, v = , so t = = .
t g v
Thus, v 2 = π Rg and v = π Rg .
(b) The putty is dislodged when F, the force holding it to the wheel,
is
mv 2
F= = mπ g
R
P6.59 (a) The wall’s normal force pushes inward:
∑F inward = mainward
becomes
2
mv 2 m ⎛ 2π R ⎞ 4π 2 Rm
n= = ⎜ =
R R ⎝ T ⎟⎠ T2
The friction and weight balance:
∑F upward = maupward
becomes
ANS. FIG. P6.59
+f – mg = 0
so with the person just ready to start sliding down,
fs = μsn = mg
Substituting,
4π 2 Rm
µs n = µs = mg
T2
Solving,
4π 2 Rµ s
T =2
gives
4π 2 Rµ s
T=
g
(b) The gravitational and friction forces

remain constant. (Static friction adjusts
to support the weight.) The normal
force increases. The person remains in
motion with the wall.
(c) The gravitational force remains constant.

The normal and friction forces decrease.
The person slides relative to the wall and
downward into the pit.
P6.60 (a)
t(s) d (m) t(s) d (m)
1.00 4.88 11.0 399
2.00 18.9 12.0 452
3.00 42.1 13.0 505
4.00 43.8 14.0 558
5.00 112 15.0 611
6.00 154 16.0 664
7.00 199 17.0 717
8.00 246 18.0 770
9.00 296 19.0 823
10.0 347 20.0 876
Chapter 6 321
(b)
(c) A straight line fits the points from t = 11.0 s to 20.0 s quite
precisely. Its slope is the terminal speed.
876 m − 399 m
vT = slope = = 53.0 m s
20.0 s − 11.0 s
P6.61 (a) If the car is about to slip down the incline, f is directed up the
incline.
∑ Fy = ncosθ + f sin θ − mg = 0
where f = µ s n. Substituting,
mg
n=
cos θ ( 1 + µ s tan θ )
µ s mg
and f =
cos θ ( 1 + µ s tan θ )
2
vmin
Then, ∑ Fx = nsin θ − f cos θ = m
R
yields
Rg ( tan θ − µ s )
vmin =
1 + µ s tan θ
When the car is about to slip up the ANS. FIG. P6.61

incline, f is directed down the incline.
Then,
∑ Fy = ncosθ − f sin θ − mg = 0, with f = µ s n
This yields
mg µ s mg
n= and f =
cos θ ( 1 − µ s tan θ ) cos θ ( 1 − µ s tan θ )
2
vmax
In this case, ∑ Fx = nsin θ + f cos θ = m , which gives
R
Rg ( tan θ + µ s )
vmax =
1 − µ s tan θ
Rg ( tan θ − µ s )
(b) If vmin = = 0 , then µ s = tan θ .
1 + µ s tan θ
P6.62 There are three forces on the child, a vertical normal force,
a horizontal force (combination of friction and a horizontal
force from a seat belt), and gravity.
∑ Fx : Fs = mv 2 R
∑ Fy : n − mg = 0 → n = mg
The magnitude of the net force is ANS. FIG. P6.62
( mv R ) + ( mg )
2 2
Fnet = 2
with a direction of
⎡ mg ⎤ −1 ⎡ gR ⎤
θ = tan −1 ⎢ 2 ⎥ = tan ⎢ 2 ⎥ above the horizontal
⎣ mv R ⎦ ⎣v ⎦
For m = 40.0 kg and R = 10.0 m:
⎡ ( 40.0 kg ) ( 3.00 m/s )2 ⎤

2
⎥ + ⎡⎣( 40.0 kg ) ( 9.80 m/s ) ⎤⎦

2
Fnet = ⎢ 2
⎢⎣ 10.0 m ⎥⎦
Fnet = 394 N
⎡ ( 9.80 m/s 2 ) ( 10.0 m ) ⎤

−1
direction: θ = tan ⎢ ⎥ → θ = 84.7°
⎢⎣ ( 3.00 m/s )2 ⎥⎦
Chapter 6 323
P6.63 The plane’s acceleration is toward the

center of the circle of motion, so it is
horizontal. The radius of the circle of
motion is (60.0 m) cos 20.0° = 56.4 m and
the acceleration is
v 2 ( 35 m s )
2
ac = =
r 56.4 m
= 21.7 m s 2
We can also calculate the weight of the
airplane:
ANS. FIG. P6.63
Fg = mg
= (0.750 kg)(9.80 m/s2)

= 7.35 N
We define our axes for convenience. In this case, two of the forces—
one of them our force of interest—are directed
 along the 20.0° line. We
define the x axis to be directed in the +T direction, and the y axis to be
directed in the direction of lift. With these definitions, the x component
of the centripetal acceleration is
acx = ac cos 20.0°
and ∑ Fx = max yields T + Fg sin 20.0° = macx

Solving for T,
T = macx − Fg sin 20.0°
Substituting,
T = (0.750 kg)(21.7 m/s2) cos 20.0° − (7.35 N) sin 20.0°
Computing,
T = 15.3 N − 2.51 N = 12.8 N
*P6.64 (a) While the car negotiates the curve, the r
accelerometer is at the angle θ .
mv 2
Horizontally: T sin θ = r
r
Vertically: T cos θ = mg
where r is the radius of the curve, and v is the r
speed of the car.
ANS. FIG. P6.64
v2
By division, tan θ =
rg
Then
v2
ac = = g tan θ :
r
ac = ( 9.80 m s 2 ) tan 15.0°
ac = 2.63 m/s 2
v2 ( 23.0 m/s )2
(b) r= gives r= = 201 m
ac 2.63 m/s 2
(c) v 2 = rg tan θ = ( 201 m ) ( 9.80 m s 2 ) tan 9.00°
v = 17.7 m/s
Challenge Problems
P6.65 We find the terminal speed from
⎛ mg ⎞ ⎡ ⎛ −bt ⎞ ⎤
v=⎜ 1 − exp ⎜
⎟ ⎝ m ⎟⎠ ⎥⎦
⎢ [1]
⎝ b ⎠⎣
where exp(x) = ex is the exponential function.

mg
At t → ∞: v → vT =
b
⎡ ⎛ −b ( 5.54 s ) ⎞ ⎤
At t = 5.54 s: 0.500vT = vT ⎢1 − exp ⎜ ⎥
⎣ ⎝ 9.00 kg ⎟⎠ ⎦
Solving,
⎛ −b ( 5.54 s ) ⎞
exp ⎜ = 0.500
⎝ 9.00 kg ⎟⎠
−b ( 5.54 s )
= ln 0.500 = −0.693
9.00 kg
b=
( 9.00 kg )( 0.693) = 1.13 kg s
5.54 s
Chapter 6 325
mg
(a) From vT = , we have
b
( 9.00 kg )( 9.80 m s2 )
vT = = 78.3 m s
1.13 kg s
(b) We substitute 0.750vT on the left-hand side of equation [1]:
⎡ ⎛ −1.13t ⎞ ⎤
0.750vT = vT ⎢1 − exp ⎜
⎣ ⎝ 9.00 s ⎟⎠ ⎥⎦
and solve for t:

⎛ −1.13t ⎞
exp ⎜ = 0.250
⎝ 9.00 s ⎟⎠
9.00 ( ln 0.250 )
t= s = 11.1 s
−1.13
(c) We differentiate equation [1] with respect to time,
dx ⎛ mg ⎞ ⎡ ⎛ bt ⎞ ⎤
=⎜ ⎟ ⎢ 1 − exp ⎜ − ⎟ ⎥
dt ⎝ b ⎠ ⎣ ⎝ m⎠ ⎦
then, integrate both sides

x t
⎛ mg ⎞ ⎡ ⎛ −bt ⎞ ⎤
∫ dx = ∫ ⎜⎝ b ⎟⎠ ⎢1 − exp ⎜⎝ m ⎟⎠ ⎥ dt
x0 0 ⎣ ⎦
t
mgt ⎛ m2 g ⎞ ⎛ −bt ⎞
x − x0 = + ⎜ 2 ⎟ exp ⎜
b ⎝ b ⎠ ⎝ m ⎟⎠ 0
mgt ⎛ m2 g ⎞ ⎡ ⎛ −bt ⎞ ⎤
= + ⎜ 2 ⎟ ⎢exp ⎜ ⎟ − 1⎥
b ⎝ b ⎠⎣ ⎝ m⎠ ⎦
At t = 5.54 s,
⎛ 5.54 s ⎞
x = ( 9.00 kg ) ( 9.80 m s 2 ) ⎜
⎝ 1.13 kg s ⎟⎠
⎛ ( 9.00 kg )2 ( 9.80 m s 2 ) ⎞
+⎜ ⎟ [ exp ( −0.693 ) − 1]
⎝ ( 1.13 kg s ) 2
⎠
x = 434 m + 626 m ( −0.500 ) = 121 m
P6.66 (a) From Problem 6.33,

dx vi
v= =
dt 1 + vi kt
x t
dt 1 t v kdt
∫ dx = ∫ vi = ∫ i
1 + vi kt k 0 1 + vi kt
0 0
1
ln ( 1 + vi kt ) 0
x t
x0 =
k
1
x − 0 = ⎡⎣ ln ( 1 + vi kt ) − ln 1⎤⎦
k
1
x = ln ( 1 + vi kt )
k
(b) We have ln ( 1 + vi kt ) = kx
vi v
1 + vi kt = e kx so v = = kxi = vi e − kx = v
1 + vi kt e
P6.67 Let the x axis point eastward, the y axis upward, and the z axis point
southward.
vi2 sin 2θ i
(a) The range is Z =
g
The initial speed of the ball is therefore
vi =
gZ
=
( 9.80 m/s )( 285 m ) = 53.0 m/s
2
sin 2θ i sin 96.0°

1 2
The time the ball is in the air is found from Δy = viy t + ay t as
2
0 = ( 53.0 m s ) ( sin 48.0° ) t − ( 4.90 m s 2 ) t 2
giving t = 8.04 s .
2π Re cosφi 2π ( 6.37 × 10 m ) cos 35.0°

6
(b) vxi = = = 379 m s

86 400 s 86 400 s
(c) 360° of latitude corresponds to a distance of 2π Re , so 285 m is a
change in latitude of
⎛ S ⎞ ⎛ 285 m ⎞
Δφ = ⎜ ( 360° ) = ⎜ ⎟ ( 360° )
⎝ 2π Re ⎟⎠ ⎝ 2π ( 6.37 × 10 m ) ⎠
6
= 2.56 × 10−3 degrees
Chapter 6 327
The final latitude is then

φ f = φi − Δφ = 35.0° − 0.002 56° = 34.997 4°
The cup is moving eastward at a speed
2π Re cosφ f
vxf =
86 400 s
which is larger than the eastward velocity of the tee by
⎛ 2π Re ⎞
Δvx = vxf − vxi = ⎜ ⎡ cosφ f − cosφi ⎤⎦
⎝ 86 400 s ⎟⎠ ⎣
⎛ 2π Re ⎞
=⎜ ⎡⎣ cos (φ − Δφ ) − cosφi ⎤⎦
⎝ 86 400 s ⎟⎠
⎛ 2π Re ⎞
=⎜
⎝ 86 400 s ⎟⎠
[ cosφi cos Δφ + sin φi sin Δφ − cosφi ]
Since Δφ is such a small angle, cos Δφ ≈ 1 and
⎛ 2π Re ⎞
Δvx ≈ ⎜ sin φi sin Δφ
⎝ 86 400 s ⎟⎠
⎡ 2π ( 6.37 × 106 m ) ⎤
Δvx ≈ ⎢ ⎥ sin 35.0°sin 0.002 56°
⎢⎣ 86 400 s ⎥⎦
= 1.19 × 10−2 m s
(d) Δx = ( Δvx ) t = ( 1.19 × 10−2 m s )( 8.04 s ) = 0.095 5 m = 9.55 cm

P6.68 (a) We let R represent the radius of the hoop and T represent the
period of its rotation. The bead moves in a circle with radius
r = R sin θ at a speed of
2π r 2π R sin θ
v= =
T T
The normal force has an inward radial
component of n sinθ and an upward component
of n cosθ .
∑ Fy = may : ncosθ − mg = 0
or
mg
n=
cos θ ANS. FIG. P6.68
v2
Then ∑ Fx = nsin θ = m becomes
r
2
⎛ mg ⎞ m ⎛ 2π R sin θ ⎞
⎜⎝ ⎟ sin θ = ⎜ ⎟⎠
cos θ ⎠ R sin θ ⎝ T
g sin θ 4π 2 R sin θ
which reduces to =
cos θ T2
This has two solutions: sin θ = 0 ⇒ θ = 0° [1]
gT 2
and cos θ = [2]
4π 2 R
If R = 15.0 cm and T = 0.450 s, the second solution yields
cos θ =
( 9.80 m s )( 0.450 s )
2 2
= 0.335 or θ = 70.4°
4π 2 ( 0.150 m )
Thus, in this case, the bead can ride at two positions: θ = 70.4°
and θ = 0° .
(b) At this slower rotation, solution [2] above becomes
cos θ =
( 9.80 m s )( 0.850 s )
2 2
= 1.20 , which is impossible.

4π 2 ( 0.150 m )
In this case, the bead can ride only at the bottom of the loop,
θ = 0° .
(c) There is only one solution for (b) because the period is too large.
(d) The equation that the angle must satisfy has two solutions
whenever 4π 2 R > gT 2 but only the solution 0° otherwise.
The loop’s rotation must be faster than a certain threshold
value in order for the bead to move away from the lowest
position. Zero is always a solution for the angle.
(e) From the derivation of the solution in (a), there are never more
than two solutions.
P6.69 At terminal velocity, the accelerating force of gravity is balanced by

friction drag:
mg = arv + br 2 v 2
Chapter 6 329
(a) (
With r = 10.0 µm, mg = 3.10 × 10−9 v + 0.870 × 10−10 v 2 ) ( )
⎡4 3⎤
For water, m = ρV = 1 000 kg m 3 ⎢ π ( 10−5 m ) ⎥
⎣3 ⎦
mg = 4.11 × 10−11 = ( 3.10 × 10−9 ) v + ( 0.870 × 10−10 ) v 2
Assuming v is small, ignore the second term on the right hand

side: v = 0.013 2 m/s
(b) (
With r = 100 µm, mg = 3.10 × 10−8 v + 0.870 × 10−8 v 2 ) ( )
Here we cannot ignore the second term because the coefficients
are of nearly equal magnitude.
mg = 4.11 × 10−8 = ( 3.10 × 10−8 ) v + ( 0.870 × 10−8 ) v 2
Taking the positive root,
−3.10 + ( 3.10 ) + 4 ( 0.870 )( 4.11)

2
v= = 1.03 m s
2 ( 0.870 )
(c) (
With r = 1.00 mm, mg = 3.10 × 10−7 v + 0.870 × 10−6 v 2 ) ( )
Assuming v > 1 m/s, and ignoring the first term:
4.11 × 10−5 = ( 0.870 × 10−6 ) v 2 v = 6.87 m s
P6.70 At a latitude of 35°, the centripetal acceleration of a plumb bob is

directed at 35° to the local normal, as can be seen from the following
diagram below at left.
Therefore, if we look at a diagram of the forces on the plumb bob and

its acceleration with the local normal in a vertical orientation, we see
the second diagram in ANS. FIG. P6.70:
ANS. FIG. P6.70
We first find the centripetal acceleration of the plumb bob. The first
figure shows that the radius of the circular path of the plumb bob is
R cos 35.0°, where R is the radius of the Earth. The acceleration is
2
v2 1 ⎛ 2π r ⎞ 4π 2 r 4π 2 R cos 35.0°
ac = = ⎜ ⎟ = 2 =
r r⎝ T ⎠ T T2
4π 2 ( 6.37 × 106 m ) cos 35.0°
= = 0.027 6 m/s 2
( 86 400 s ) 2
Apply the particle under a net force model to the plumb bob in both x
and y directions in the second diagram:
x: T sin φ = mac sin 35.0°

y: mg − T cosφ = mac cos 35.0°
Divide the equations:
ac sin 35.0°
tan φ =
g − ac cos 35.0°
tan φ =
( 0.027 6 m/s ) sin 35.0° 2
= 1.62 ×10 −3
9.80 m/s − ( 0.027 6 m/s ) cos 35.0°

2 2
φ = tan −1 ( 1.62 × 10−3 ) = 0.092 8°
Chapter 6 331
ANSWERS TO EVEN-NUMBERED PROBLEMS
P6.2 (a) 1.65 × 103 m/s; (b) 6.84 × 103 s

P6.4 215 N, horizontally inward
P6.6 ( )
(a) −0.233î + 0.163 ĵ m/s 2 ; (b) 6.53 m/s, −0.181î + 0.181ĵ m/s 2 ( )
P6.8 (a) ( 68.6 N ) î + ( 784 N ) ĵ ; (b) a = 0.857 m/s2
P6.10 The situation is impossible because the speed of the object is too small,
requiring that the lower string act like a rod and push rather than like
a string and pull.
P6.12 (a) the gravitational force and the contact force exerted on the water by
the pail; (b) contact force exerted by the pail; (c) 3.13 m/s; (d) the water
would follow the parabolic path of a projectile
P6.14 (a) 4.81 m/s; (b) 700 N
P6.16 (a) 2.49 × 104 N; (b) 12.1 m/s
P6.18 (a) 20.6 N; (b) 32.0 m/s2 inward, 3.35 m/s2 downward tangent to the
circle; (c) 32.2 m/s2 inward and below the cord at 5.98˚; (d) no change;
(e) acceleration is regardless of the direction of swing
P6.20 (a) 3.60 m/s2; (b) T = 0; (c) noninertial observer in the car claims that
the forces on the mass along x are T and a fictitious force (−Ma); (d)
inertial observer outside the car claims that T is the only force on M in
the x direction
P6.22 93.8 N
2 ( vt − L )
P6.24
( g + a)t2
P6.26 (a) 53.8 m/s; (b) 148 m
P6.28 (a) 6.27 m/s2 downward; (b) 784 N directed up; (c) 283 N upward
P6.30 (a) 32.7 s–1; (b) 9.80 m/s2 down; (c) 4.90 m/s2 down
P6.32 36.5 m/s
P6.34 (a) 2.03 N down; (b) 3.18 m/s2 down; (c) 0.205 m/s down
P6.36 101 N
P6.38 1.2 × 103 N
4
P6.40 (a) 1.15 × 10 N up; (b) 14.1 m/s
P6.42 See Problem 6.42 for full derivation.
P6.44 (a) 217 N; (b) 283 N; (c) T2 > T1 always, so string 2 will break first
P6.46 The situation is impossible because the speed of the child given in the
problem is too large: static friction could not keep the child in place on
the incline
P6.48 0.835 rev/s
P6.50 (a) v = Rg tan 35.0° = (6.86 m/s ) R ; (b) the mass is unnecessary;
2
(c) increasing the radius will make the required speed increase; (d)
when the radius increases, the period increases; (e) the time interval
required is proportional to R / R = R
mv 2
P6.52 (a) 1 975 lb; (b) −647 lb; (c) When Fg′ = 0, then mg = .
R
⎛ m2 ⎞
P6.54 (a) m2g; (b) m2g; (c) ⎜⎝ m ⎟⎠ gR ; (d) The puck will spiral inward, gaining
1
speed as it does so; (e) The puck will spiral outward, slowing down as
it does so
 
P6.56 (a) a = +kv; (b) ∑ F = kmv ; (c) some feedback mechanism could be used
to impose such a force on an object; (d) think of a duck landing on a
lake, where the water exerts a resistive force on the duck proportional
to its speed
P6.58 (a) π Rg ; (b) mπ g
P6.60 (a) See table in P6.60 (a); (b) See graph in P6.60 (b); (c) 53.0 m/s
P6.62 84.7°
P6.64 (a) 2.63 m/s2; (b) 201 m; (c) 17.7 m/s
1
P6.66 (a) x = ln ( 1 + vi kt ) ; (b) v = vi e − kx
k
P6.68 (a) θ = 70.4° and θ = 0°; (b) θ = 0°; (c) the period is too large; (d) Zero
is always a solution for the angle; (e) there are never more than two
solutions
P6.70 0.092 8°

Chapter 6 Ansers PDF

Uploaded by

Copyright:

Available Formats

Chapter 6 Ansers PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 6 Ansers PDF

Uploaded by

Copyright:

Available Formats

6

Circular Motion and Other

6.1 Extending the Particle in Uniform Circular Motion Model

* An asterisk indicates a question or problem new to this edition.

ANSWERS TO OBJECTIVE QUESTIONS

OQ6.1 (a) A > C = D > B = E = 0. At constant speed, centripetal acceleration is

OQ6.5 Answer (b). The magnitude of acceleration decreases as the speed

ANSWERS TO CONCEPTUAL QUESTIONS

other matter. Second, astronauts in orbit are moving in a circular path.

SOLUTIONS TO END-OF-CHAPTER PROBLEMS

Section 6.1 Extending the Particle in

v= g moon r = (1.52 m s )(1.7 × 10

Therefore, ∑ F is proportional to v2 and increases by a factor of

This force must be horizontally inward to produce the driver’s

The car’s acceleration at point B is then

at 35.0° north of west

(b) From part (a), v = 6.53 m s

(c) We find the average acceleration from

ac = v 2 /r so v = ac r = ( 3.00 m s )(60.0 m ) = 13.4 m s

Solving for the tension T gives

(a) The force of static friction causes

P6.10 We solve for the tensions in the two strings:

The angle θ is given by

T cos 48.6° + T cos 48.6° =

To answer the What if?, we go back to equation [2] above and

We then add this equation to equation [2] to obtain

∑ Fx = max giving fs = mar

v ≤ µ s rg = 0.600 ( 35.0 m ) ( 9.80 m/s 2 ) → v ≤ 14.3 m/s

Section 6.2 Nonuniform Circular Motion

and the contact force exerted on the water by the pail .

= (1.33 m/s ) + (1.20 m/s )

(b) At point B, the centripetal acceleration is now downward, and

The maximum speed at B corresponds to the case where the

vmax = Rg = ( 15.0 m )( 9.80 m/s 2 ) = 12.1 m/s

Newton’s second law gives

In a teardrop-shaped loop, the radius of curvature r decreases,

ar = = = 32.0 m/s 2 inward

= 3.35 m/s 2 downward tangent to the circle

(c) The magnitude of the acceleration is

a = ar2 + at2 = ( 32.0 m/s ) + ( 3.35 m/s )

32.2 m/s 2 inward and below the cord at 5.98°

P6.19 Let the tension at the lowest point be T. From

He doesn’t make it across the river because the vine breaks.

Section 6.3 Motion in Accelerated Frames

(b) If v = const, a = 0, so T = 0 . (This is also an equilibrium

ANS. FIG. P6.20

Solving for θ , θ = 17.0°

(b) From equation [1],

The top layer of water feels a downward force of gravity mg and an

Section 6.4 Motion in the Presence of

(b) From v 2f = vi2 + 2gh = 0 + 2gh, we solve for h:

P6.27 With 100 km/h = 27.8 m/s, the resistive force is

P6.28 Given m = 80.0 kg, vT = 50.0 m/s, we write

(b) At v = 50.0 m/s, terminal velocity has been reached.

(c) At v = 30.0 m/s,

P6.30 (a) The acceleration of the Styrofoam is given by

(b) At t = 0, v = 0, and a = g = 9.80 m s 2 down

(c) When v = 0.150 m/s,

= 4.90 m/s 2 down