[1] EU-TYPE EXAMINATION CERTIFICATE

[2] Equipment or Protective System intended for use


in Potentially Explosive Atmospheres
Directive 2014/34/EU

[3] EU-Type Examination Certificate Number: DEMKO 17 ATEX 1823X Rev. 1

[4] Product: MAXIMUS MMX, CCTV camera housing

[5] Manufacturer: Videotec S.p.A.

[6] Address: Via Friuli 6, 36015 Schio (VI) Italy

[7] This product and any acceptable variation thereto are specified in the schedule to this certificate and the documents therein referred to.

[8] UL International Demko A/S, notified body number 0539 in accordance with Article 17 of the Council Directive 2014/34/EU of 26 February
2014, certifies that this product has been found to comply with the Essential Health and Safety Requirements relating to design and
construction of Equipment or Protective System intended for use in potentially explosive atmospheres given in Annex II to the Directive.
The examination and test results are recorded in confidential report no. 4423698.1068477

[9] Compliance with the Essential Health and Safety Requirements has been assured by compliance with:

EN 60079-0:2012+A11:2013 EN 60079-1:2014 EN 60079-31:2014

[10] If the sign "X" is placed after the certificate number, it indicates that the product is subject to special conditions for safe use specified in the
schedule to this certificate.

[11] This EU-Type Examination Certificate relates only to the design and construction of the specified product. Further requirements of the
Directive apply to the manufacturing process and supply of this product. These are not covered by the certificate.

[12] The marking of the product shall include the following:

 II 2 G Ex db IIB T6...T5 Gb
 II 2 D Ex tb IIIC T85°C...T100°C Db

This is to certify that the sample(s) of the Product described herein (“Certified Product”) has been investigated
and found in compliance with the Standard(s) indicated on this Certificate, in accordance with the ATEX Product
Certification Manager Certification Program Requirements. This certificate and test results obtained apply only to the product
sample(s) submitted by the Manufacturer. UL did not select the sample(s) or determine whether the sample(s)
Jan-Erik Storgaard provided were representative of other manufactured product. UL has not established Follow-Up Service or other
surveillance of the product. The Manufacturer is solely and fully responsible for conformity of all product to all
applicable Standards, specifications, requirements or Directives. The test results may not be used, in whole or in
part, in any other document without UL’s prior written approval.

Date of issue: 2017-09-15

Re-issued: 2017-12-19

Notified Body UL International Demko A/S, Borupvang 5A, 2750 Ballerup, Denmark
Tel. +45 44 85 65 65, [email protected], www.ul.com

00-IC-F0056-1 – Issue 18.1 This certificate may only be reproduced in its entirety and without any change, schedule included. Page 1 of 3
[13] Schedule
[14] EU-TYPE EXAMINATION CERTIFICATE No.
DEMKO 17 ATEX 1823X Rev. 1
[15] Description of Product
The MAXIMUS MMX explosion-proof housing has been designed for use with cameras operating in industrial environments in which
there may be an explosive atmosphere due to gas, vapors, mists, or air powder mixtures.

The MAXIMUS MMX intend to be fitted with a camera by the end user with a maximum power output of 4.5 W for a camera with video
encoder preinstalled by manufacturer or 5.8 W if video encoder is integrated in the camera. It is a fixed CCTV camera housing that can
be mounted at any angle. It may be provided with an optional sunshield. The camera housing includes a cover and an enclosure body.

The circular front cover is fitted with a toughened glass window cemented in place and is provided with a spigot portion for securing to
the enclosure body.

The enclosure body is fitted with female threaded connection points for connection of the optional sunshield and of the bracket kit.

The enclosure body provides one 1/2” NPT cable entry for end user connection to either, cable connectors or a conduit system
dependent on application. The internal part of the enclosure is fitted with a gear tray for mounting the intended end user camera. In
addition, the gear tray provides all the internal circuitry comprising of supply terminals, heating board and a fan. The heating board and
the fan maintain the internal temperature within a minimum and a maximum when the equipment is powered.

Access to the integral terminal compartment for termination of supply or replacement of either of the fitted fuse or inputs and outputs is
via the removal of the six M5 screws securing the cover to the body housing.

Externally the equipment, other than the cemented windows, is manufactured from passivated, electro-polished AiSi 316L stainless
steel.

Installation instruction:

• The cameras to be installed shall not be electromagnetic or contain lasers, continuous wave sources or ultrasonic energy
radiating equipment.
• The cameras to be installed shall not contain cells or batteries.
• The cameras to be installed shall dimensionally be no greater than 52 mm wide x 52 mm high x 78 mm long and be of a
basic geometric form.
• Cable entries and field wiring must be suitable for an operating temperature as specified in the following table:

Maximum ambient Cable entry temperature

temperature range
-40 °C to +65 °C +83.2°C
-40 °C to +70 °C +88.2°C

Nomenclature for type MAXIMUS MMX:

MMXabcde

Where:

a Voltage (2) 24 Vac/Vdc & PoE+

b Camera (0) Without camera
other than 0 = pre-installed camera
c Connection (0) No cable, no cable gland
other than 0 = Connection devices
d Video output (0) with videoencoder integrated in the camera
(Z) IP H.264 protocol ONVIF Profile S
e Variation Internal use – One alphanumeric character without meanings for safety to identify the release

Temperature range
The relation between maximum ambient temperature and the assigned temperature class is as follows:

Maximum ambient temperature range Temperature class

-40 °C to +65 °C T6
-40 °C to +70 °C T5

Electrical data

Electrical rating (comprising the max Max power dissipation of installed camera
Supply Voltage power dissipation of the installed camera With video encoder With video encoder
and intermittent internal heaters) integrated in the camera preinstalled by manufacturer
24 Vac 1.32 A 50/60 Hz 21 W
24 Vdc 0.9 A - 20 W 5.8 W 4.5 W
PoE+ 0.46 A - 21 W

00-IC-F0056-1 – Issue 17.0 This certificate may only be reproduced in its entirety and without any change, schedule included. Page 2 of 3
[13] Schedule
[14] EU-TYPE EXAMINATION CERTIFICATE No.
DEMKO 17 ATEX 1823X Rev. 1
Routine tests
Routine overpressure tests in accordance with EN 60079-1:2014 clause 16.3 shall be conducted on all units, at a pressure of 13.23 bar
for a duration of not less than 10 seconds. There shall be no sign of damage, deformation or rupture that will invalidate the concept of
protection.

[16] Descriptive Documents

The scheduled drawings are listed in the report no. provided under item no. [ 8 ] on page 1 of this EU-Type Examination Certificate.

[17] Specific conditions of use:

• The outside surface of the product must never be covered in more than 5 mm of dust.
• In order to prevent accumulation of electrostatic charges whilst cleaning, the device should be cleaned using a damp cloth.
• Ambient temperature and Surface temperature – see instructions.
• Contact the manufacturer for information on the dimensions of the explosion proof joint.

[18] Essential Health and Safety Requirements

The Essential Health and Safety Requirements (EHSRs) covered by the standards listed at item 9.

Additional information
The product has in addition passed the test for Ingress Protection to IP 66 in accordance with
EN60529:1991+A1:2000+A2:2013 for Unclassified applications.

The trademark will be used as the company identifier on the marking label.

The manufacturer shall inform the notified body concerning all modifications to the technical documentation as described
in Annex III to Directive 2014/34/EU of the European Parliament and the Council of 26 February 2014.

00-IC-F0056-1 – Issue 17.0 This certificate may only be reproduced in its entirety and without any change, schedule included. Page 3 of 3