New Product

Miniature Power Relays

MY(S)

MY(S) Versatile plug-in Relay

• Reduces wiring work by 60% when combined with the
PYF-PU Push-In Plus Socket
(according to actual OMRON measurements).
• 10 A (DPDT) and 5 A (4PDT)
• Gold-clad contacts (MY4(S))
• Test button (lockable)
• Wide portfolio includes hermetically sealed and
latching types
• 2.6 mm wide pins offer higher conductivity and less
temperature increase
The compliant standards depend on the model.
Refer to the Common Relay Precautions and For details, refer to information provided for individual models.
Safety Precautions on page 34.

Model Number Structure

Coil Polarity Type Contact form Plug-In socket/solder terminals Flange mounting
(DC case) *

With LED indicator With LED Indicator Without LED

and Lockable test Indicator
button
Type 1 Standard model DPDT MY2N(S) MY2IN(S) MY2(S) MY2F
DPDT (Bifurcated) MY2ZN --- --- ---
4PDT MY4N(S) MY4IN(S) MY4(S) MY4F
4PDT (Bifurcated) MY4ZN(S) MY4ZIN(S) MY4Z(S) MY4ZF
With Built-in diode DPDT MY2N-D2(S) MY2IN-D2(S) --- ---
(DC only)
DPDT (Bifurcated) MY2ZN-D2 --- --- ---
4PDT MY4N-D2(S) MY4IN-D2(S) --- ---
4PDT (Bifurcated) MY4ZN-D2(S) MY4ZIN-D2(S) --- ---
With Built-in CR DPDT MY2N-CR(S) MY2IN-CR(S) --- ---
(AC only)
4PDT MY4N-CR(S) MY4IN-CR(S) --- ---
4PDT (Bifurcated) MY4ZN-CR(S) MY4ZIN-CR(S) --- ---
High reliability contacts 4PDT
(Crossbar --- --- MY4Z-CBG ---
Bifurcated)
Plastic Sealed 4PDT MYQ4N --- --- ---
4PDT (Bifurcated) --- --- MYQ4Z ---
Lactching (coil latching) DPDT --- --- MY2K ---
Hermetic 4PDT --- --- MY4H ---
4PDT (Bifurcated) --- --- MY4ZH ---
Type 2 Standard model DPDT MY2N1(S) MY2IN1(S) --- ---
4PDT MY4N1(S) MY4IN1(S) --- ---
4PDT (Bifurcated) MY4ZN1(S) MY4ZIN1(S) --- ---
With Built-in diode DPDT MY2N1-D2(S) MY2IN1-D2(S) --- ---
(DC only)
4PDT MY4N1-D2(S) MY4IN1-D2(S) --- ---
4PDT (Bifurcated) MY4ZN1-D2(S) MY4ZIN1-D2(S) --- ---
* In case of AC coil type relay, please select them from "Type 1" of Coil Polality.

Refer to Connection Socket and Mounting Bracket Selection Table on page 25 in Options for information on the
possible combinations of Models with Plug-in Terminals and Sockets.

1
 MY(S)
Contents
Model Number Structure............................................................................................. 1
Specifications
Coil Ratings ............................................................................................................ 2
MY2(S)/MY4(S)/MY4Z(S).............................................................................................. 3
Engineering Data ......................................................................................................... 6
Detailed Information on Models Certified for Safety Standards, MY2(S)/MY4(S)/MY4Z(S) ......... 8
Models Other Than MY(S) Models
MY2ZN ..................................................................................................................... 9
MY@F..................................................................................................................... 11
Detailed Information on Models Certified for Safety Standards, MY2ZN and MY@F.......... 14
MY4Z-CBG ............................................................................................................ 15
MYQ4 ..................................................................................................................... 17
MY2K ..................................................................................................................... 19
MY4(Z)H................................................................................................................. 21
Socket for MY............................................................................................................. 23
Options.................................................................................................................. 25
Safety Precautions .................................................................................................... 34

Specifications
Coil Ratings
MY(S)
Must Must
Coil inductance Max. Power
Rated current Coil operate release
Rated voltage (reference value) voltage consumption
resistance voltage voltage
(approx.)
50 Hz 60 Hz Arm. OFF Arm. ON % of rated voltage
6V 214.1 mA 183 mA 12.2 Ω 0.04 H 0.08 H
12 V 106.5 mA 91 mA 46 Ω 0.17 H 0.33 H
24 V 53.8 mA 46 mA 180 Ω 0.69 H 1.30 H Approx. 0.9 to
AC 30% min.
48/50 V 24.7/25.7 mA 21.1/22.0 mA 788 Ω 3.22 H 5.66 H 1.3 VA (60 Hz)

110/120 V 9.9/10.8 mA 8.4/9.2 mA 4,430 Ω 19.20 H 32.1 H

220/240 V 4.8/5.3 mA 4.2/4.6 mA 18,790 Ω 83.50 H 136.4 H 80% max. 110%
6V 151 mA 39.8 Ω 0.17 H 0.33 H
12 V 75 mA 160 Ω 0.73 H 1.37 H
DC 24 V 37.7 mA 636 Ω 3.20 H 5.72 H 10% min. 0.9 W
48 V 18.8 mA 2,560 Ω 10.60 H 21.0 H
100/110 V 9.0/9.9 mA 11,100 Ω 45.60 H 86.2 H
Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with tolerances of +15%/–20% for rated currents and ±15% for DC coil
resistance.
2. Performance characteristic data are measured at a coil temperature of 23°C.
3. AC coil resistance and impedance are provided as reference values (at 60 Hz).
4. Power consumption drop was measured for the above data. When driving transistors, check leakage current and connect a bleeder resistor if required.

MY2ZN, MY@F, MY4(Z)H

Item Rated current (mA) Coil inductance (H) Must- Must-
Coil resistance Maximum Power consumption
Rated Armature Armature operate release
50 Hz 60 Hz (Ω) voltage (V) (VA, W)
voltage (V) OFF ON voltage (V) voltage (V)

12 106.5 91 46 0.17 0.33

24 53.8 46 180 0.69 1.3
100/110 11.7/12.9 10/11 3,750 14.54 24.6 Approx. 0.9 to 1.3 VA
AC 30% min.*2
110/120 9.9/10.8 8.4/9.2 4,430 19.2 32.1 (60 Hz)

200/220 6.2/6.8 5.3/5.8 12,950 54.75 94.07 110% of rated

80% max.*1
220/240 4.8/5.3 4.2/4.6 18,790 83.5 136.4 voltage

12 75 160 0.73 1.37

24 36.9 650 3.2 5.72
DC 10% min.*2 Approx. 0.9
48 18.5 2,600 10.6 21.0
100/110 9.1/10 11,000 45.6 86.2
Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with tolerances of +15%/−20% for the AC rated current and ±15% for the
DC coil resistance.
2. The AC coil resistance and inductance values are reference values only (at 60 Hz).
3. Operating characteristics were measured at a coil temperature of 23°C.
4. The maximum voltage capacity was measured at an ambient temperature of 23°C.
*1. There is variation between products, but actual values are 80% max.
To ensure operation, apply at least 80% of the rated value
*2. There is variation between products, but actual values are 30% minimum for AC and 10% minimum for DC. To ensure release, use a value that is lower than the
specified value.
Note: Refer to page 19 for the coil specifications of the MY2K.

2
 MY(S)

Miniature Power Relays: MY2(S)/MY4(S)/MY4Z(S)

Refer to the standards certifications and compliance
section of your OMRON website for the latest
information on certified models.

Specifications
Contact Ratings
DPDT 4PDT 4PDT (bifurcated)
Item Resistive load Inductive load Resistive load Inductive load Resistive load Inductive load
(cos φ = 1) (cos φ = 0.4, L/R = 7 ms) (cos φ = 1) (cos φ = 0.4, L/R = 7 ms) (cos φ = 1) (cos φ = 0.4, L/R = 7 ms)
5A, 250 VAC 2A, 250 VAC 3 A, 250 VAC 0.8 A, 250 VAC 3 A, 250 VAC 0.8 A, 250 VAC
Rated load
5A, 30 VDC 2 A, 30 VDC 3 A, 30 VDC 1.5 A, 30 VDC 3 A, 30 VDC 1.5 A, 30 VDC
Carry current 10 A (see note) 5 A (see note)
Max. switching 250 VAC
voltage 125 VDC
Max. switching
10 A 5A
current
Contact
Ag Au cladding + Ag alloy
materials
Failure rate
5 VDC, 1 mA 1 VDC, 1 mA 1 VDC, 100 μA
(reference value)
Note: Don’t exceed the carry current of a Socket in use. Please see page 23.

Characteristics
Item All Relays
Contact resistance 100 mΩ max. (50 mΩ: 4PDT bifurcated)
Operate time 20 ms max.
Release time 20 ms max.
Mechanical:18,000 operations/hr
Max. operating frequency
Electrical:1,800 operations/hr (under rated load)
Insulation resistance 100 MΩ min. (at 500 VDC)
Dielectric strength 2,000 VAC, 50/60 Hz for 1.0 min (1,000 VAC between contacts of same polarity)
Destruction:10 to 55 to 10 Hz, 0.5 mm single amplitude (1.0 mm double amplitude)
Vibration resistance
Malfunction:10 to 55 to 10 Hz, 0.5 mm single amplitude (1.0 mm double amplitude)
Destruction:1,000 m/s2
Shock resistance
Malfunction:200 m/s2
Endurance See the following table.
Ambient temperature Operating: –55 to 70°C (with no icing)
Ambient humidity Operating: 5 to 85% RH
Weight Approx. 35 g
Note: The values given above are initial values.

Endurance Characteristics
Electrical life
Contact form Mechanical life (at 18,000 operations/hr)
(at 1,800 operations/hr under rated load)
DPDT AC:50,000,000 operations min. 500,000 operations min.
4PDT DC:100,000,000 operations min. 200,000 operations min.
4PDT (bifurcated) 20,000,000 operations min. 100,000 operations min.

3
 MY(S)
Dimensions (Unit: mm)

List of Models
MY2@@(S) Series

2.6

8 Eight, 1.2-dia. × 2.2 oval holes

6.3

0.5
28 max.
5

8.05 36 max. 6.4

14.2 21.5 max.

Note: The picture is lockable test Terminal Arrangement/Internal Connections (Bottom View)
button type.
MY2IN(S) MY2IN(S) MY2IN-D2(S) MY2IN-CR
(AC Model) (DC Models) (DC Models Only) (AC Models Only)

1 4 1 4 1 4 1 4

5 8 5 8 5 8 5 8

9 12 9 12 9 12 9 12

− + − +
13 14 13 14 13 14 13 14

MY2IN1(S) MY2IN1-D2(S)
(DC Models) (DC Models Only)

1 4 1 4

5 8 5 8

9 12 9 12

+ − + −
13 14 13 14

Note: For the DC models, check the coil polarity when wiring and wire all connections correctly.

4
 MY(S)

MY4@@(S) series

2.6

8 Fourteen, 1.2-dia. × 2.2 oval holes

6.3

0.5
28 max.
5

8.05 36 max. 6.4

14.2 21.5 max.

Note: The picture is lockable test Terminal Arrangement/Internal Connections (Bottom View)
button type.
MY4(Z)IN(S) MY4(Z)IN(S) MY4(Z)IN-D2(S) MY4(Z)IN-CR(S)
(DC Models) (AC Models) (DC Models Only) (AC Models Only)

1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4

5 6 7 8 5 6 7 8 5 6 7 8 5 6 7 8

9 10 11 12 9 10 11 12

− + − +
13 14 13 14 13 14 13 14

MY4(Z)IN1(S) MY4(Z)IN1-D2(S)
(DC Models) (DC Models Only)

1 2 3 4 1 2 3 4

5 6 7 8 5 6 7 8

+ − + −
13 14 13 14

Note: For the DC models, check the coil polarity when wiring and wire all connections correctly.

5
 MY(S)
Engineering Data MY2(S)/ MY4(S)/MY4Z(S)
Maximum Switching Capacity Endurance Curve
MY2(S) MY2(S) MY2(S)
10,000 10,000

Number of operations (×103 operations)

100

Number of operations (×103 operations)

Contact current (A)

50 5,000 5,000

30 3,000 250 VAC 3,000

resistive load 250 VAC
AC resistive load AC inductive load inductive load
(cos φ = 0.4)
10 1,000 1,000 30 VDC
30 VDC inductive load
5 500 resistive load 500
30 VDC
3 300 resistive load 300 30 VDC
DC resistive load inductive load
250 VAC
250 VAC 100 inductive load
1 100
resistive load

0.5 50 50

0.3 DC inductive load 30 30

(L/R = 7)

0.1 10 10
1 3 5 10 30 50 100 250 500 0 2 4 6 8 10 0 1 2 3 4 5
Contact voltage (V) Contact current (A) Contact current (A)
MY4(S) and MY4Z(S) MY4(S) MY4(S)
100 10,000 10,000
Number of operations (×103 operations)

Number of operations (×103 operations)

Contact current (A)

50 5,000 5,000
250 VAC
30 3,000 3,000
resistive load
30 VDC
inductive load
10 AC resistive load AC inductive load 1,000 1,000
(cos φ = 0.4)
30 VDC 30 VDC
5 500 500
resistive load inductive load
3 300 300
30 VDC
DC resistive load resistive load 250 VAC
1 100 100 inductive load

250 VAC
0.5 50 50 250 VAC
resistive load
inductive load
0.3 DC inductive load 30 30
(L/R = 7)

0.1 10 10
1 3 5 10 30 50 100 250 500 0 1 2 3 4 5 0 0.5 1 1.5 2
Contact voltage (V) Contact current (A) Contact current (A)
MY4Z(S) MY4Z(S)
10,000 10,000
Number of operations (×103 operations)

Number of operations (×103 operations)

5,000 5,000
3,000 3,000

1,000 250 VAC 1,000

resistive load 30 VDC
500 500 inductive load

300 30 VDC 300 30 VDC

resistive load inductive load

100 100
30 VDC 250 VAC
resistive load inductive load
50 50
250 VAC
30 30
resistive load 250 VAC
inductive load

10 10
0 1 2 3 4 5 0 0.5 1 1.5 2
Contact current (A) Contact current (A)

Common Specifications for MY2(S)/MY4(S)/MY4Z(S)

Malfunctioning Shock
Y
N = 20
Energized Measurement: Shock was applied 3 times each in 6 directions along 3 axes with
550
Not energized the Relay energized and not energized to check the shock values that cause the
400 Relay to malfunction.
Z'
X 600 Criteria: Non-energized: 200 m/s2 ,
700
Energized: 200 m/s2
600
300
Shock direction

250

550 600
Z 600 X'
400

Unit: m/s2
600

Y'

6
 MY(S)
Engineering Data MY(S) (MY2ZN, MY@F)
Ambient Temperature vs. Ambient Temperature vs. Coil Temperature Rise
Must-operate and Must-release Voltage
MY2 AC Models MY2 AC Models, 50 Hz MY2 DC Models
100 Number of Relays: 10 120 120
Must-operate voltage

Temperature rise (°C)

Temperature rise (°C)

Must-operate/must-release voltage (%)

(average value) Must-release voltage 110 When rated voltage is applied 110 When rated voltage is applied

80 100 Operating temperature limit value 100 Operating temperature limit value
(E-class insulation, 120° C) (E-class insulation, 120° C)
90 90

80 80
60
70 70

60 5 A contact current × 2 circuits 60

40 50 2.5 A contact current × 2 circuits 50 5 A contact current × 2 circuits
40 40 2.5 A contact current × 2 circuits

30 No contact current 30
20
20 20 No contact current

10 10
0
−60 −30 0 30 60 90 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
MY2 DC Models MY4 AC Models, 50 Hz MY4 DC Models
100 120 120
Temperature rise (°C)

Temperature rise (°C)

Number of Relays: 10 Must-operate voltage
Must-operate/must-release voltage (%)

(average value) Must-release voltage

110 When rated voltage is applied 110 When rated voltage is applied

100 Operating temperature limit value 100 Operating temperature limit value
80 (E-class insulation, 120° C) (E-class insulation, 120° C)
90 90
80 80
60 70 70

60 60
3 A contact current × 4 circuits
40 50 50
3 A contact current × 4 circuits
40 1.5 A contact current × 4 circuits 40
1.5 A contact current × 4 circuits
30 No contact current 30
20
20 20 No contact current

10 10
0
−60 −30 0 30 60 90 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
Models with built-in diodes
MY4 AC Models The diode absorbs surge from the coil. This type is best suited for applications with semiconductor circuits.
With Diode Without Diode
100
Number of Relays: 10 Must-operate voltage
Must-operate/must-release voltage (%)

(average value) Must-release voltage

80
ON OFF ON OFF

60

40 140 V

24 VDC A
20 To digital
Di memory To digital
24 VDC
memory
A’ A’
0
−60 −30 0 30 60 90
Note: 1. Make sure that the polarity is correct.
Ambient temperature (°C)
2. The release time will increase, but the 20-ms specification for standard models is satisfied.
MY4 DC Models 3. Diode properties:The diode has a reversed dielectric strength of 1,000 V.
Forward current: 1 A
100
Number of Relays: 10
Models with Built-in CR Circuits
Must-operate voltage
Must-operate/must-release voltage (%)

(average value) Must-release voltage

80
With CR Without CR

60 282 V
282 V 2.5
msec
ms

40
80 V

20
4.12 ms
9.4 ms 600 V
A
0 A
−60 −30 0 30 60 90 C = 0.033 μF To digital
200 AC
Ambient temperature (°C) R = 6.8 kΩ 200 AC memory
scope
A’ A’

7
 MY(S)
Detailed Information on Models Certified for Safety Standards, MY2(S)/MY4(S)/MY4Z(S)
VDE-certified Models (No. 112467UG, EN61810-1)
Model Coil ratings Contact form Contact ratings File No. Certified number of operations
6, 12, 24, 48/50, 100/ 10 A, 250 VAC (cos φ = 1)
110, 110/120, 200/ DPDT MY2: 10,000 operations
10 A, 30 VDC (L/R = 0 ms)
MY@ 220, and 220/240 VAC 6692 (VDE0435) MY4: 100,000 operations
6, 12, 24, 48, 100/ 5 A, 250 VAC (cos φ = 1) MY4Z: 50,000 operations (AC)
4PDT
110, and 125 VDC 5 A, 30 VDC (L/R = 0 ms)

UL508-certified Models (File No. 41515)

Model Coil ratings Contact form Contact ratings File No. Certified number of operations
10A, 250 VAC (General Use)
10A, 30 VDC (General Use)
7A, 240 VAC (General Use)
7A, 24 VDC (Resistive)
6,000
5A, 240 VAC (General Use)
5A, 250 VAC (Resistive)
DPDT
5A, 30 VDC (Resistive)
3A, 265 VAC (Resistive)
1/6HP, 250 VAC
6 to 240 VAC 1/8HP, 265 VAC 1,000
MY@ E41515 (UL508)
6 to 125 VDC 1/10HP, 120 VAC
B300 Pilot Duty (Same polarity) 6,000
5A, 28 VDC (General Use) (Same polarity)
5A, 240 VAC (General Use) (Same polarity)
5A, 30 VDC (Resistive) (Same polarity) 6,000
5A, 250 VAC (Resistive) (Same polarity)
4PDT
0.2A, 120 VDC (Resistive) (Same polarity)
1/6HP, 250 VAC (Same polarity)
1,000
1/10HP, 120 VAC (Same polarity)
B300 Pilot Duty (Same polarity) 6,000

CSA 22.2 No. 14-certified Models (File No. LR31928)

Model Coil ratings Contact form Contact ratings File No. Certified number of operations
7A, 240 VAC (General Use)
7A, 24 VDC (Resistive)
5A, 240 VAC (General Use)
6,000
5A, 250 VAC (Resistive)
5A, 30 VDC (Resistive)
DPDT
3A, 265 VAC (Resistive)
1/6HP, 250 VAC
1/8HP, 265 VAC 1,000
1/10HP, 120 VAC LR31928
6 to 240 VAC
MY@ (CSA C22.2)
6 to 125 VDC B300 Pilot Duty (Same polarity) 6,000
(No. 14)
5A, 240 VAC (General Use) (Same polarity)
5A, 28 VDC (General Use) (Same polarity)
5A, 250 VAC (Resistive) (Same polarity) 6,000
5A, 30 VDC (Resistive) (Same polarity)
4PDT
0.2A, 120 VDC (Resistive) (Same polarity)
1/6HP, 250 VAC (Same polarity)
1,000
1/10HP, 120 VAC (Same polarity)
B300 Pilot Duty (Same polarity) 6,000

LR-certified Models (File No. 98/10014)

Model Coil ratings Contact form Contact ratings File No. Certified number of operations
10 A, 250 VAC (resistive)
2 A, 250 VAC (PF0.4)
DPDT
10 A, 30 VDC (resistive)
6 to 240 VAC 2 A, 30 VDC (L/R = 7 ms) MY2: 50,000 operations
MY@ 98/10014
6 to 125 VDC 5 A, 250 VAC (resistive) MY4: 50,000 operations
0.8 A, 250 VAC (PF0.4)
4PDT
5 A, 30 VDC (resistive)
1.5 A, 30 VDC (L/R = 7 ms)

8
 MY(S)

Miniature Power Relays: MY2ZN

Refer to the standards certifications and compliance
section of your OMRON website for the latest
information on certified models.

Specifications
Contact Ratings
Load Inductive load Type Standard Model with built-in operation
Resistive load
Item (cos φ = 0.4, L/R = 7 ms) Item models indicator, diode, or CR circuit
5 A at 220 VAC 2 A at 220 VAC Ambient
Rated load
5 A at 24 VDC 2 A at 24 VDC operating −55 to 70° C −55 to 60° C*2
temperature*1
Rated carry current 5A
Ambient
Maximum contact voltage 250 VAC, 125 VDC
operating 5% to 85%
Maximum contact current 5A humidity
Contact form DPDT (Bifurcated) *1. With no icing or condensation.
*2. This limitation is due to the diode junction temperature and elements used.
Contact materials Au plating + Ag

Characteristics
Item MY2ZN series
Contact resistance*1 50 mΩ max.
Operation time*2 20 ms max.
Release time*2 20 ms max.
Maximum Mechanical 18,000 operations/h
operating
frequency Rated load 1,800 operations/h

Insulation resistance*3 100 MΩ min.

Between coil and contacts
Between contacts of 2,000 VAC at 50/60 Hz for 1 min.
Dielectric
different polarity
strength
Between contacts of the
1,000 VAC at 50/60 Hz for 1 min.
same polarity

Vibration Destruction 10 to 55 to 10 Hz, 0.5-mm single amplitude (1.0-mm double amplitude)

resistance Malfunction 10 to 55 to 10 Hz, 0.5-mm single amplitude (1.0-mm double amplitude)

Shock Destruction 1,000 m/s2

resistance Malfunction 200 m/s2
Mechanical 50,000,000 operations min. (operating frequency: 18,000 operations/h)
Endurance
*4
Electrical 200,000 operations min. (rated load, switching frequency: 1,800 operations/h)

Item MY2ZN Note: These are initial values.

*1. Measurement conditions: 1 A at 5 VDC using the voltage drop method.
Failure rate P value
100 μA at 1 VDC *2. Measurement conditions: With rated operating power applied.
(reference value)*5 Ambient temperature condition: 23° C
Weight Approx. 35 g *3. Measurement conditions: For 500 VDC applied to the same location as for dielectric strength measurement.
*4. Ambient temperature condition: 23°C
*5. This value was measured at a switching frequency of 120 operations per minute.

9
 MY(S)
Dimensions (Unit: mm)

MY2ZN, MY2ZN-D2
MY2ZN MY2ZN MY2ZN-D2
(AC Models) (DC Models) (DC Models Only)

2.6

Eight, 1.2-dia. × 2.2 oval holes

0.5
28 max.

36 max. 6.4 (The coil has no polarity.) Check the coil polarity when wiring
21.5 max. and wire all connections correctly.
Check the coil polarity when wiring
* For the MY2Z-CR and MY2ZN-CR, and wire all connections correctly.
this dimension is 53 mm max.
Note: 1. An AC model has coil disconnection self-diagnosis.
2. For the DC models, check the coil polarity when wiring and wire all connections
correctly.
3. The indicator is red for AC and green for DC.
4. The operation indicator indicates the energization of the coil and does not
represent contact operation.

10
 MY(S)

Flange-mounting Relays: MY@F

Refer to the standards certifications and compliance
section of your OMRON website for the latest
information on certified models.

Specifications
Contact Ratings
Contact form DPDT 4PDT, 4PDT (Bifurcated)
Load Inductive load Inductive load
Resistive load Resistive load
Item (cos φ = 0.4, L/R = 7 ms) (cos φ = 0.4, L/R = 7 ms)
5 A at 220 VAC 2 A at 220 VAC 3 A at 220 VAC 0.8 A at 220 VAC
Rated load
5 A at 24 VDC 2 A at 24 VDC 3 A at 24 VDC 1.5 A at 24 VDC
Rated carry current 5A 3A
Maximum contact voltage 250 VAC, 125 VDC
Maximum contact current 5A 3A
Contact form DPDT 4PDT, 4PDT (Bifurcated)
Contact materials Ag Au plating + Ag

Type
MY@F
Item
*
Ambient operating temperature −55 to 70° C
Ambient operating humidity 5% to 85%
* With no icing or condensation.

Characteristics
Item Contact form DPDT 4PDT, 4PDT (Bifurcated)
Contact resistance*1 50 mΩ max.
Operation time*2 20 ms max.
Release time*2 20 ms max.
Maximum Mechanical 18,000 operations/h
operating
frequency Rated load 1,800 operations/h
*3
Insulation resistance 100 MΩ min.
Between coil and contacts
Between contacts of 2,000 VAC at 50/60 Hz for 1 min.
Dielectric
different polarity
strength
Between contacts of the
1,000 VAC at 50/60 Hz for 1 min.
same polarity
10 to 55 to 10 Hz, 0.5-mm single amplitude
Destruction
Vibration (1.0-mm double amplitude)
resistance 10 to 55 to 10 Hz, 0.5-mm single amplitude
Malfunction
(1.0-mm double amplitude)
Shock Destruction 1,000 m/s2
resistance Malfunction 200 m/s2
AC: 50,000,000 operations min.
Mechanical DC: 100,000,000 operations min.
(switching frequency: 18,000 operations/h)
Endurance
500,000 operations min. 200,000 operations min.
Electrical*4 (rated load, switching (rated load, switching
frequency: 1,800 operations/h) frequency: 1,800 operations/h)

Item Contact form DPDT 4PDT, 4PDT (Bifurcated)

Failure rate P value
1 mA at 5 VDC 1 mA at 1 VDC
(reference value)
Weight Approx. 35 g
Note: These are initial values.
*1. Measurement conditions: 1 A at 5 VDC using the voltage drop method
*2. Measurement conditions: With rated operating power applied. Ambient temperature condition: 23° C
*3. Measurement conditions: For 500 VDC applied to the same location as for dielectric strength measurement.
*4. Ambient temperature condition: 23° C
*5. This value was measured at a switching frequency of 120 operations per minute.

11
 MY(S)
Dimensions (Unit: mm)

Flange mounting
MY@F
2.6
Mounting Hole Dimensions

Two, 3.5-dia. holes

or M3 screw holes
Fourteen, 1.2-dia. × 2.2 oval holes
2

38 ±0.2

4.35
0.5
29 max. 38 44 max.

0.5 6.4 Note: Refer to the terminal arrangement and

The above figure is for the MY4F. 36 max. 3.5 internal connections diagrams for the
MY2(S), MY4(S) and MY4Z(S).
22.5 max.

12
 MY(S)
Engineering Data MY@F
Maximum Switching Capacity Endurance Curve
MY2F MY2F MY2F
10

Number of operations (×104 operations)

AC resistive load
Contact current (A)

Number of operations (×104 operations)

5 AC inductive load
(cos φ = 0.4)
500 500

110 VAC resistive load 110 VAC inductive load

DC resistive load (cos φ = 0.4)
1 220 VAC resistive load
100 100
220 VAC inductive load
0.5 DC inductive load (cos φ = 0.4)
(L/R = 7 ms) 50 50

24 VDC inductive load

24 VDC resistive load (L/R = 7 ms)

0.1
10 10

5 10 50 100 500 0 1 2 3 4 5 6 7 0 1 2 3
Contact voltage (V) Contact current (A) Contact current (A)
MY4F and MY4ZF MY4F MY4F

Number of operations (×104 operations)

10
Number of operations (×104 operations)
Contact current (A)

AC resistive load
5
500 500

AC inductive load 110 VAC resistive load

(cos φ = 0.4)

1 220 VAC resistive load 110 VAC inductive load (cos φ = 0.4)
100 100
0.5
DC resistive load 50 50

DC inductive load
(L/R = 7 ms) 30 VDC
220 VAC inductive load 30 VDC inductive load
resistive load
0.1 10 10 (cos φ = 0.4) (L/R = 7 ms)

5 10 50 100 500 0 1 2 3 0 0.5 1.0 1.5

Contact voltage (V) Contact current (A) Contact current (A)
MY4ZF MY4ZF
Number of operations (×104 operations)
Number of operations (×104 operations)

500 500

100 100
110 VAC inductive load (cos φ = 0.4)

50 50
220 VAC resistive load
24 VDC inductive load (L/R = 7 ms)

10 10
24 VDC resistive load
220 VAC inductive load (cos φ = 0.4)

0 1 2 3 0 0.5 1.0 1.5

Contact current (A) Contact current (A)

Common Specifications for MY@F

Malfunctioning Shock
Y
N = 20
Energized Measurement: Shock was applied 3 times each in 6 directions along 3 axes with
550
Not energized the Relay energized and not energized to check the shock values that cause the
400 Relay to malfunction.
Z'
X 600 Criteria: Non-energized: 200 m/s2 ,
700
Energized: 200 m/s2
600
300
Shock direction

250

550 600
Z 600 X'
400

Unit: m/s2
600

Y'

13
 MY(S)
Detailed Information on Models Certified for Safety Standards, MY2ZN and MY@F
• The standard models are certified for UL and CSA standards.
• The rated values for safety standard certification are not the same as individually defined performance values. Always check the specifications before use.

TÜV-certified Models (File No. R50030059) CSA-certified Models (File No. LR31928)
Coil Contact Certified number Coil Contact Certified number
Model Contact ratings Model Contact ratings
ratings form of operations ratings form of operations

6 to 125 DPDT 5 A, 250 VAC (cos φ = 1.0) 7A, 240 VAC (Resistive)
VDC 3 A, 120 VAC (cos φ = 1.0) 7A, 24 VDC (Resistive)
MY@ 10,000 operations
6 to 240 4PDT 0.8 A, 120 VAC (cos φ =
VDC 5A, 240 VAC (General Use) 6,000
0.4)
DPDT 5A, 250 VAC (Resistive)
UL-certified Models (File No. E41515)
5A, 30 VDC (Resistive)
Coil Contact Certified number
Model Contact ratings 1/6HP, 250 VAC
ratings form of operations 1,000
1/10HP, 120 VAC
7A, 240 VAC (General Use)
7A, 240 VAC (General Use)
7A, 24 VDC (Resistive) 6 to 240
(Same polarity)
VAC
5A, 240 VAC (General Use) MY@
6,000 6 to 125 7A, 24 VDC (Resistive)
5A, 250 VAC (Resistive) VDC (Same polarity)
5A, 30 VDC (Resistive) 5A, 240 VAC (General Use)
DPDT (Same polarity) 6,000
3A, 265 VAC (Resistive)
4PDT 5A, 30 VDC (Resistive)
1/6HP, 250 VAC
5A, 250 VAC (Resistive)
1/8HP, 265 VAC 1,000 (Same polarity)
1/10HP, 120 VAC 0.2A, 120 VDC (Resistive)
B300 Pilot Duty 6,000 1/6HP, 250 VAC
1,000
6 to 240 5A, 28 VDC (General Use) 1/10HP, 120 VAC
VAC (Same polarity)
MY@
6 to 125 5A, 240 VAC (General Use) • When ordering models that are certified for Lloyd’s Register (LR) Standards,
VDC (Same polarity) be sure to specify “LR-certified Model” with your order.

5A, 30 VDC (Resistive)

6,000 LR-certified Models (File No. 90/10270)
(Same polarity)
Contact
5A, 250 VAC (Resistive) Model Coil ratings Contact ratings
form
(Same polarity)
4PDT 2 A, 30 VDC inductive load
0.2A, 120 VDC (Resistive) 6 to 240 DPDT
2 A, 200 VAC inductive load
(Same polarity) VAC
MY@ 1.5 A, 30 VDC inductive load
6 to 125
1/6HP, 250 VAC 4PDT 0.8 A, 200 VAC inductive load
VDC
(Same polarity) 1.5 A, 115 VAC inductive load
1,000
1/10HP, 120 VAC
(Same polarity)
B300 Pilot Duty
6,000
(Same polarity)

14
 MY(S)

Miniature Power Relays: MY4Z-CBG

Specifications
Contact Ratings Characteristics
Load Inductive load Contact resistance*1 100 mΩ max.
Resistive load
Item (cos φ = 0.4, L/R = 7 ms) Operation time*2 20 ms max.
1 A at 220 VAC 0.3 A at 220 VAC Release time*2 20 ms max.
Rated load
1 A at 24 VDC 0.5 A at 24 VDC
Maximum Mechanical 18,000 operations/h
Rated carry operating
1A Electrical 1,800 operations/h
current frequency
Maximum contact Insulation resistance*3 100 MΩ
250 VAC, 125 VDC
voltage Between coil
Maximum contact and contacts
1A 2,000 VAC at 50/60 Hz for 1 min.
current Dielectric Between contacts
Contact form 4PDT (Crossbar bifurcated) strength of different polarity
Between contacts
Contact materials Au cladding + AgPd 700 VAC at 50/60 Hz for 1 min.
of the same polarity
10 to 55 to 10 Hz, 0.5-mm single amplitude
Destruction
Vibration (1.0-mm double amplitude)
resistance 10 to 55 to 10 Hz, 0.5-mm single amplitude
Malfunction
(1.0-mm double amplitude)
Shock Destruction 1,000 m/s2
resistance Malfunction 200 m/s2
5,000,000 operations min. (operating
Mechanical
frequency: 18,000 operations/hr)
Endurance
50,000 operations min. (switching
Electrical*4
frequency: 1,800 operations/h) at rated load
Failure rate P value (reference value)*5 100 μA at 1 VDC
Ambient operating temperature −25 to 70°C (with no icing or condensation)
Ambient operating humidity 5% to 85%
Weight Approx. 35 g
Note: The above values are initial values.
*1. Measurement conditions: 1 A at 5 VDC using the voltage drop method
*2. Measurement conditions: With rated operating power applied, not including
contact bounce.
Ambient temperature condition: 23° C
*3. Measurement conditions: For 500 VDC applied to the same location as for
dielectric strength measurement.
*4. Ambient temperature condition: 23° C
*5. This value was measured at a switching frequency of 120 operations per
minute.

Engineering Data
Maximum Switching Capacity Contact Reliability Test
(Modified Allen Bradley Circuit)
Contact load: 5 VDC, 1 mA resistive load
MY4Z-CBG Malfunction criteria level: Contact resistance of 100 Ω

10 30
Contact resistance (mΩ)
Contact current (A)

Number of Relays: 10 (average value)

5 Malfunction rate: λ60 = 0.0046 × 10-6 per operation
(switching frequency: 200 operations/ min.)
28
AC resistive load
AC inductive load
(cos φ = 0.4)
1 26

0.5
24
DC resistive load

0.1 DC inductive load 22

(L/R = 7 ms)
0.05
Current-carrying contact
20
Open contacts
Self-latching contacts
Closed contacts
0.01 0
1 5 10 50 100 500 1 5 10 50 100 500 1,000
Contact voltage (V) Number of operations (×104 operations)

15
 MY(S)
Dimensions (Unit: mm)

MY4Z-CBG

Terminal Arrangement/Internal
2.6 Connections (Bottom View)
Standard Models

Fourteen, 1.2-dia. × 2.2 oval holes

0.5

28 max.

6.3

0.5 21.5 max. (The coil has no polarity.)

36 max. 6.4

Safety Precautions
Refer to the Common Relay Precautions.
Applicable Sockets
Use only combinations of OMRON Relays and Sockets.

16
 MY(S)

Plastic Sealed Relays: MYQ4

Specifications
Contact Ratings
Type Inductive load
Resistive load
Item (cos φ = 0.4, L/R = 7 ms)
Rated load 1 A at 220 VAC, 1 A at 24 VDC 0.5 A at 220 VAC, 0.5 A at 24 VDC
Rated carry current 1A
Maximum contact voltage 250 VAC, 125 VDC
Maximum contact current 1A
Maximum switching capacity
220 VAC, 24 W 110 VAC, 12 W
(reference value)
Failure rate P value
Single contacts: 1 mA at 1 VDC, Bifurcated contacts: 100 μA at 1 VDC
(reference value)
Contact form 4PDT, 4PDT (Bifurcated)
Contact materials Au plating + Ag
* This value was measured at a switching frequency of 120 operations per minute.

Ambient operating temperature −55 to 60° C*

Ambient operating humidity 5% to 85%
* With no icing or condensation.

Characteristics
Contact resistance*1 50 mΩ max.
Operation time *2
20 ms max.
Release time*2 20 ms max.
Maximum Mechanical 18,000 operations/h
operating
frequency Rated load 1,800 operations/h
Between coil and contacts 1,500 VAC at 50/60 Hz for 1 min.
Dielectric
strength
Between contacts of different polarity 1,500 VAC at 50/60 Hz for 1 min.
Between contacts of the same polarity 1,000 VAC at 50/60 Hz for 1 min. Note: The values at the left are initial
values.
Insulation resistance*3 100 MΩ min. *1. Measurement conditions: 1 A at 5
VDC using the voltage drop
Vibration Destruction 10 to 55 to 10 Hz, 0.5-mm single amplitude (1.0-mm double amplitude) method
resistance Malfunction 10 to 55 to 10 Hz, 0.5-mm single amplitude (1.0-mm double amplitude) *2. Measurement conditions: With
rated operating power applied, not
Destruction 1,000 m/s2 including contact bounce.
Shock Ambient temperature condition:
resistance Malfunction 200 m/s2 23° C
*3. Measurement conditions: For 500
AC: 50,000,000 operations (5,000,000*4) min., DC: 100,000,000 operations VDC applied to the same location
Mechanical
(5,000,000*4) min. (switching frequency: 18,000 operations/h) as for dielectric strength
Endurance measurement.
200,000 operations min. (100,000 operations*4) (rated load, switching *4. This value is for bifurcated
Electrical*5
frequency: 1,800 operations/h) contacts.
*5. Ambient temperature condition:
Weight Approx. 35 g 23° C

Engineering Data
Maximum Switching Capacity Endurance Curve H2S Gas Data Malfunctioning Shock
MYQ4(Z) MYQ4 MYQ4 Y

10 1,000 80 Energized
Contact resistance (mΩ)
Number of operations (×104 operations)

550
Contact current (A)

7 700 N=10 Not energized

5 500 70 Measurements: Temperature: 40° C, Humidity: 60% to 70%, 400
AC resistive load H2S concentration: 5 ±3 ppm X 600 Z’
3 300 600
AC inductive load The change in contact resistance was measured after 700
220 VAC resistive load
(cos φ = 0.4) 60 leaving the Relay in the above environment for a fixed
24 VDC resistive load amount of time, then removing it to a constant-temperature 300
1 100
0.7 50 and constant-humidity environment for at least 30 minutes.
70
0.5 50 250
0.3 40
30
DC resistive load 550 600
220 VAC inductive load (cos φ = 0.4) 30
DC inductive load Z 600 X’
0.1 10 400
(L/R = 7 ms) max.
24 VDC inductive load (L/R = 7 ms)
0.07 7 min.
0.05 20 Unit: m/s2
5 600
0.03 3
10
N = 20 Y’

0.01 1 Measurement: Shock was applied Shock

1
1 3 5 10 30 50 100 300 500 1,000 0 0.2 0.4 0.6 0.8 1.0 1.2 1 3 5 10 30 50 100 300 500 1,000
3 times each in 6 directions along direction
Contact voltage (V) Contact current (A) Standing time (h) 3 axes with the Relay energized
Note: The durability of bifurcated and not energized to check the
contacts is one-half that of shock values that cause the Relay
single contacts. to malfunction.
Criteria: Non-energized: 200 m/s2
Energized: 200 m/s2

17
 MY(S)
Dimensions (Unit: mm)

Relays with Plug-in Terminals or Soldered Terminals MYQ4(Z)N

MYQ4(Z)(N)
DC Models AC Models

2.6
21.5 max.

Fourteen, 1.2-dia. × 2.2 oval holes

6.4

28 max. 28 max.

35.5 max. 21.5 max. Check the coil polarity when wiring (The coil has no polarity.)
and wire all connections correctly.
Note: 1. An AC model has coil disconnection self-
diagnosis.
2. For the DC models, check the coil polarity
when wiring and wire all connections
correctly.

Safety Precautions
• For models with built-in operation indicators, check the coil polarity when Relay Replacement
wiring and wire all connections correctly (DC operation).
• Use only combinations of OMRON Relays and Sockets. To replace the Relay, turn OFF the power supply to the load and Relay coil
sides to prevent unintended operation and possible electrical shock.

18
 MY(S)

Latching Relays: MY2K

Specifications
Coil Rating
Set coil Reset coil Power consumption (VA, W)
Item Set voltage Reset Maximum
Rated current (mA) Coil Rated current (mA) Coil (V) voltage (V) voltage (V) Set coil Reset coil
Rated voltage (V) 50 Hz 60 Hz resistance (Ω) 50 Hz 60 Hz resistance (Ω)
12 57 56 72 39 38.2 130
Approx. 0.6 Approx. 0.2
AC 24 27.4 26.4 320 18.6 18.1 550 to 0.9 to 0.5
(at 60 Hz) (at 60 Hz)
100 7.1 6.9 5,400 3.5 3.4 3,000 110% max. of
80% max. 80% max.
12 110 110 50 235 rated voltage
DC 24 52 470 25 940 Approx. 1.3 Approx. 0.6
48 27 1,800 16 3,000
Note: 1. The rated current for AC is the value measured with a DC ammeter in half-wave rectification.
2. The rated current and coil resistance are measured at a coil temperature of 23°C with tolerances of +15%/−20% for the AC rated current and ±15% for the
DC coil resistance.
3. The AC coil resistance is a reference value only.
4. Operating characteristics were measured at a coil temperature of 23°C.
5. The maximum voltage capacity was measured at an ambient temperature of 23°C.

Contact Ratings Characteristics

Load Inductive load Contact resistance*1 50 mΩ max.
Resistive load
Item (cos φ = 0.4, L/R = 7 ms) Time*2 AC: 30 ms max., DC: 15 ms max.
3 A at 220 VAC 0.8 A at 220 VAC Set
Rated load Minimum pulse width AC: 60 ms, DC: 30 ms
3 A at 24 VDC 1.5 A at 24 VDC
Time*2 AC: 30 ms max., DC: 15 ms max.
Rated carry Reset
3A Minimum pulse width AC: 60 ms, DC: 30 ms
current
Maximum contact Maximum Mechanical 18,000 operations/h
250 VAC, 125 VDC operating
voltage Rated load 1,800 operations/h
frequency
Maximum contact
3A Insulation resistance*3 100 MΩ
current
Contact form DPDT Between coil
and contacts
Contact materials Au plating + Ag 1,500 VAC at 50/60 Hz for 1 min.
Between contacts of
Dielectric different polarity
Ambient operating
−55 to 60° C* strength Between contacts of
temperature
the same polarity
Ambient operating 1,000 VAC at 50/60 Hz for 1 min.
5% to 85% Between set/
humidity
reset coils
* With no icing or condensation.
10 to 55 to 10 Hz, 0.5-mm single amplitude
Destruction
Vibration (1.0-mm double amplitude)
resistance 10 to 55 to 10 Hz, 0.5-mm single amplitude
Malfunction
(1.0-mm double amplitude)
Shock Destruction 1,000 m/s2
resistance Malfunction 200 m/s2
100,000,000 operations min.
Mechanical
(switching frequency: 18,000 operations/h)
Endurance
200,000 operations min.
Electrical*4
(at 1,800 operations/hr, rated load)
Failure rate P value (reference value)*5 1 mA at 1 VDC
Weight Approx. 30 g
Note: The above values are initial values.
*1. Measurement conditions: 1 A at 5 VDC using the voltage drop method
*2. Measurement conditions: With rated operating power applied, not including
contact bounce.
*3. Measurement conditions: For 500 VDC applied to the same location as for
dielectric strength measurement.
*4. Ambient temperature condition: 23° C
*5. This value was measured at a switching frequency of 120 operations per
minute.

19
 MY(S)
Engineering Data
MY2K
Maximum Switching Capacity Endurance Curve

Number of operations (×104 operations)

10

Number of operations (×104 operations)

Contact current (A)

5 AC resistive load

500 500

AC inductive load
(cos φ = 0.4) 110 VAC resistive load
110 VAC inductive load
1 (cos φ = 0.4)
220 VAC resistive load 100
100
0.5 DC resistive load
50 50

DC inductive load
(L/R = 7 ms) 30 VDC resistive load 220 VAC 30 VDC inductive load
0.1 10 inductive load (L/R = 7 ms)
10
(cos φ = 0.4)

5 10 50 100 500 0 1 2 3 0 0.5 1 1.5

Contact voltage (V) Contact current (A) Contact current (A)

MY2K 100 VAC MY2K 24 VDC

Malfunctioning Shock Magnetic Interference Latching Deterioration Over
(External Magnetic Field) Time
Not energized Y
1000 (Average values)

Latching deterioration over time (%)

N = 24
Energized Measurement: The rate of deterioration in latching ability was
Armature deviation N=5 measured over time with the Relay left at a normal temperature
900 Measurement: The percentage of change in the operating and (20 to 30°C) after latching by applying the rated voltage.
when set release voltages in a uniform external magnetic field
1000 were measured (worst magnetic field direction).
X 800 Z
400
N S S N 100
700 400 80 Average value

Percentage
change (%)
400 60
N = 20 90
40
300 Measurement: Shock was applied 2 20 Set voltage
400
times each in 6 directions along 3 80 60 40
80
350
axes with the Relay energized and not −20
40 60 80

Z’
1000
X’
1000 energized to check the shock values −40
Reset voltage
70
900 that cause the Relay to malfunction. −60
−80
1000 Unit: m/s2 Criteria: Non-energized: 200 m/s2 60
Y’
Energized: 200 m/s2 0 50 100 300 500 1,000 5,000 10,000
Uniform magnetic field strength (0e) Elapsed time (h)

Dimensions (Unit: mm)

Relays with Plug-in Terminals or Soldered Terminals Terminal Arrangement/Internal

MY2K Connections (Bottom View)

For AC
2.6

Ten, 1.2-dia. × 2.2 oval holes

0.5

28 max.
6.3
Note: R is a resistor for ampere-turn correction. This resistor is
0.5
21.5 max.
built-in to 50-VAC and higher models.
36 max. 6.4 (The coil has no polarity.)

Safety Precautions
• For applications that use a 200 VAC power supply, connect external resistors Rs and Rr to a 100 VAC Relay.
• Do not apply a voltage to the set and reset coils at the same time. If you apply the rated voltage to both coils 1 4
simultaneously, the Relay will be set.
5 8
• The minimum pulse width in the performance column is the value for the following measurement conditions: an ambient
temperature of 23° C with the rated operating voltage applied to the coil. The performance values given here may not be 9 10 11 12
satisfied due to use over time and a reduction in latching performance due to changes in the ambient temperature or in
the conditions of the application circuit. 13 14
For actual use, apply the rated operating voltage with a pulse width based on the actual load and reset the Relay at least Rr
once per year to prevent degradation over time.
• If the Relay is used in an environment with strong magnetic fields, the surrounding magnetic field can demagnetize the Rs Rs: 7.3 kΩ, 3 W min.
magnetic body and cause unintended operation. Therefore, do not use these Relays in environments with strong Set power supply
Rr: 14.3 kΩ, 1 W min.
magnetic fields. Reset power supply

Relay Replacement
To replace the Relay, turn OFF the power supply to the load and Relay coil sides to prevent unintended operation and possible electrical shock.

Applicable Sockets
Use only combinations of OMRON Relays and Sockets.

20
 MY(S)

Hermetically Sealed Relays: MY4(Z)H

Specifications
Contact Ratings Characteristics
Load MY4H MY4ZH Contact resistance*1 50 mΩ max.
Inductive load Inductive load Operation time*2 20 ms max.
Resistive Resistive
Item cos φ = 0.4 cos φ = 0.4
load load Release time*2 20 ms max.
L/R = 7 ms L/R = 7 ms
3 A at 110 VAC 0.8 A at 110 VAC 3 A at 110 VAC 0.8 A at 110 VAC Maximum Mechanical 18,000 operations/h
Rated load operating
3 A at 24 VDC 1.5 A at 24 VDC 3 A at 24 VDC 1.5 A at 24 VDC Rated load 1,800 operations/h
frequency
Rated carry
3A Insulation resistance*4 100 MΩ min.
current
Maximum contact 125 VAC Between coil
voltage 125 VDC Dielectric and contacts 1,000 VAC at 50/60 Hz for 1 min.
Maximum contact strength Between contacts (700 VAC between contacts of the same polarity.)
3A of different polarity
current
Contact form 4DPDT 4DPDT (Bifurcated) 10 to 55 to 10 Hz, 0.5-mm single amplitude
Destruction
Vibration (1.0-mm double amplitude)
Contact materials Au plating + Ag
resistance 10 to 55 to 10 Hz, 0.5-mm single amplitude
Malfunction
Ambient operating (1.0-mm double amplitude)
temperature
−25 to 60° C*
Shock Destruction 1,000 m/s2
Ambient operating resistance Malfunction 200 m/s2
humidity
5% to 85%
50,000,000 operations (5,000,000 operations*4) min.
Mechanical
* With no icing or condensation. (operating frequency: 18,000 operations/h)
Endurance
100,000 operations (50,000 operations*4) min. rated
Electrical*5
load, switching frequency: 1,800 operations/h)
Failure rate P value Single contacts: 100 μA at 1 VDC
(reference value)*6 Bifurcated contacts: 100 μA at 100 mVDC
Weight Approx. 50 g
Note: The above values are initial values.
*1. Measurement conditions: 1 A at 5 VDC using the voltage drop method
*2. Measurement conditions: With rated operating power applied, not including
contact bounce.
Ambient temperature condition: 23° C
*3. Measurement conditions: For 500 VDC applied to the same location as for
dielectric strength measurement.
*4. This value is for bifurcated contacts.
*5. Ambient temperature condition: 23° C
*6. This value was measured at a switching frequency of 120 operations per
minute.

Engineering Data
Maximum Switching Capacity Endurance Curve
MY4(Z)H MY4H
Number of operations (×104 operations)
Contact current (A)

AC resistive load
5
500
AC inductive load
110 VAC resistive load
(cos φ = 0.4)

1 24 VDC resistive load

100

0.5 50
DC resistive load
DC inductive load
(L/R = 7 ms)

0.1 10
110 VAC inductive load
(cos φ = 0.4) 24 VDC inductive load (L/R = 7 ms)

5 10 50 100 500 0 1 2 3
Contact voltage (V) Contact current (A)
Note: The durability of bifurcated contacts is one-half that of single contacts.

21
 MY(S)
Dimensions (Unit: mm)

Relays with Plug-in Terminals or Soldered Terminals Terminal Arrangement/

MY4(Z)H Internal Connections
(Bottom View)

2.6

Fourteen, 1.2-dia. × 3 oval holes 22 max.

0.5
28.5 max.
(The coil has no polarity.)

35 max. 6.4

Safety Precautions
Applicable Sockets
Use only combinations of OMRON Relays and Sockets.
Application Environment for Hermetically Sealed
Relays
Humid environments can cause insulation problems, which may result in short-
circuiting or unintended operation.

Solution
Do not use these Relays in any environment where the Relay will come into
contact with water vapor, condensation, or water droplets. This can reduce the
surface tension of the insulating beads and cause short-circuiting or unintended
operation due to poor insulation.

Relay Replacement
To replace the Relay, turn OFF the power supply to the load and Relay coil
sides to prevent unintended operation and possible electrical shock.

22
 MY(S)

Sockets for MY
DIN-rail-mounted (DIN-rail) Socket
Conforms to VDE 0106, Part 100
• Snap into position along continuous sections of any
mounting DIN-rail.
• Facilitates sheet metal design by standardized mounting
dimensions.
• Design with sufficient dielectric separation between
terminals eliminates the need of any insulating sheet.

Specifications
Terminal No. of Dielectric Insulation resistance
Mounting Appearance Model Carry current
type poles withstand voltage (see note 2)

2 PYF-08-PU 10 A

Push-In Plus
2,000 VAC, 1 min 1,000 MΩ min
terminals

4 PYF-14-PU 6A

PYFZ-08-E/
10 A 2,250 VAC, 1 min
PYFZ-08

PYF08A-E/
2 7A 1,000 MΩ min
PYF08A

2,000 VAC, 1 min

PYF08A-N (see note 3) 7 A (see note 4)

DIN-rail-mounted
Socket Screw terminals

PYFZ-14-E/
6A 2,250 VAC, 1 min
PYFZ-14

PYF14A-E/
4 5A 1,000 MΩ min
PYF14A

2,000 VAC, 1 min

PYF14A-N (see note 3) 5 A (see note 4)

PYF14-ESS-B

Rise-Up 2 and 4
12 A > 3 KV > 5 MΩ
terminals Common

PYF14-ESN-B

23
 MY(S)

Terminal No. of Dielectric Insulation resistance

Mounting Appearance Model Carry current
type poles withstand voltage (see note 2)

PY08/
2 7A 1000 MΩ min.
PY08-Y1

Solder terminals

PY14/
4 3A
PY14-Y1

PY08QN/
2 7A
PY08QN-Y1
Back-connecting 1,500 VAC, 1 min

Wrapping
terminals 100 MΩ min.

PY14QN/
4 3A
PY14QN-Y1

2 PY08-02 7A
Relays with
PCB terminals
4 PY14-02 3A

Note: 1. The values given above are initial values.

2. The values for insulation resistance were measured at 500 VDC at the same place as the dielectric strength.
3. The maximum operating ambient temperature for the PYF08A-N and PYF14A-N is 55°C.
4. When using the PYF08A-N or PYF14A-N at an operating ambient temperature exceeding 40°C, reduce the current to 60%.
5. The MY2(S) can be used at 70°C with a carry current of 7 A.

24
 MY(S)

Options (Order Separately)

Connection Socket and Mounting Bracket Selection Table
(The possible combinations of models with plug-in terminals and sockets)
Connecting method Front-mounting Sockets (PYF□)
Back-mounting Sockets (PY□)
Mounting method Track or screw mounting
Screw
Push-In Wrapping terminals
terminals Relays
Screw Rise-Up Plus
Terminal Type (finger Solder terminals with PCB
terminals terminals Terminal Terminal length: Terminal length:
protection Terminals *4
Block *3 25 mm 20 mm
structure) *2
(Order
Without 　 With 　 Without With Without With Without With
No. of (Order separately: separately
Model Release 　 Release 　 Mounting Mounting Mounting Mounting Mounting Mounting
poles Hold-down Clips) *1 : Hold-down
Lever Lever Brackets *1 Brackets Brackets *1 Brackets Brackets *1 Brackets
Clips) *1
PYFZ-08-E
MY2(S),
PYFZ-08 (PYC-A1)
MY2ZN
(PYC-A1) PYF08A-E
(except
PYF08A (PYC-A1)
for MY2K@,
(PYC-A1) PYF08A-N
MY2Z@-CR)
(PYC-A1) PY08 PY08QN PY08QN2 PY08-02
PY08-Y1 PY08QN-Y1 PY08QN2-Y1
PYFZ-08-E (PYC-P) (PYC-P) (PYC-P) (PYC-P)
PYFZ-08 (PYC-E1)
(PYC-E1) PYF08A-E
8 MY2I(S) *5 PYF-08-PU
PYF08A (PYC-E1)
(PYC-E1) PYF08A-N PYF14-ESN-B
(PYC-E1) (PYC-35-B)
PYFZ-08-E PYF14-ESS-B
PYFZ-08 (Y92H-3) (PYC-35-B)
(Y92H-3) PFY08A-E PY08 PY08QN PY08QN2 PY08-02
MY2Z-@-CR *6 PY08-Y3
PYF08A (Y92H-3) (PYC-1) (PYC-1) (PYC-1) (PYC-1)
(Y92H-3) PFY08A-N
(Y92H-3)
MY4(S), PYFZ-14-E
MY4I(S), PYFZ-14 (PYC-A1)
MY4-CBG, (PYC-A1) PYF14A-E PY14 PY14QN PY14QN2 PY14-02
14 PYF-14-PU PY14-Y1 PY14QN-Y1 PY14QN2-Y1
MY4Q, PYF14A (PYC-A1) (PYC-P) (PYC-P) (PYC-P) (PYC-P)
MY4(Z)H, (PYC-A1) PYF14A-N
MY2K (PYC-A1)
Note: Refer to Common Socket and DIN Track Products for the external dimensions of the Socket Relays and details on Hold-down Clips.
*1. The information in parentheses is the model number of the applicable Mounting Bracket. Mounting Brackets are sold in sets of two. However,
the PYC-P is just one Mounting Bracket.
*2. The PYF@A-E has a terminal cover with finger protection. The Socket and Terminal Cover are integrated into one unit. Round terminals cannot
be used. Use forked terminals or ferrules instead.
*3. A Push-In Plus Terminal Block Socket functions as a release lever to hold or remove a Relay. Refer to PYF-@@-PU/P2RF-@@-PU for details.
*4. If an MYI@(S) Relay with a Latching Lever is used in combination with a PY@-02 Socket for Relays with PCB Terminal Socket and PYC-P
Mounting Brackets, the lever will not operate.
*5. We recommends using the PYC-E1 Mounting Bracket for a MY2I(S) Relay with Latching Lever. (If the PYC-A1 is used with the MY2I(S), the
latching lever will be blocked by the Mounting Bracket and the lever will not operate.)
*6. The Mounting Brackets are applicable for Relays with a height of 36 mm or less. If the Relay height is greater than 53 mm, use Y92H-3 for the
Front-mounting Socket and PYC-1 for the Back-mounting Socket. (The Y92H-3 is a set of two Brackets and the PYC-1 is just one Bracket.)

Terminal Covers for PYFZ-08/PYFZ-14 Sockets

Applicable model Model
PYFZ-08 PYCZ-C08 (2 pcs/set)
PYFZ-14 PYCZ-C14 (1 pcs/set)
Note: These covers cannot be used for PYF08A and PYF14A.
Use these covers in a combination with PYFZ-08 and PYFZ-14.

Mounting Plates for Sockets

Socket model For 1 Socket For 18 Sockets For 36 Sockets
PY08, PY08QN(2), PY14, PY14QN(2) PYP-1 PYP-18 PYP-36
Note: PYP-18 and PYP-36 can be cut into any desired length in accordance with the number of Sockets.

DIN-rail and Accessories

Supporting DIN-rail (length = 500 mm) PFP-50N
Supporting DIN-rail (length = 1,000 mm) PFP PFP-100N, PFP-100N2
End Plate PFP-M
Spacer PFP-S

25
 MY(S)

Safety Standards for Sockets

Front-mounted Sockets (PYF@)
Model Standards File No.
TÜV (EN 61984) ---
PYF-08-PU
UL508 E87929
PYF-14-PU
CSA C22.2 No.14 ---
PYF14A-E, PYF14A-N VDE0627 (EN61984) Nr.B387 (License No.)
TÜV(EN 61984) R50405329
PYFZ-08-E, PYFZ-08
UL508 E87929
PYFZ-14-E, PYFZ-14
CSA22.2 LR31928
TÜV(EN 61984) J50224549
PYF08A-E, PYF08A-N
UL508 E87929
PYF14A-E, PYF14A-N
CSA22.2 LR31928

PYF14-ESN-B UL508 E244189

PYF14-ESS-B CSA22.2 LR225761

PYF08A UL508 E87929

PYF14A CSA22.2 LR31928

Back-connecting Sockets (PY@)

Model Standards File No.

PY08(-02) UL508 E87929

PY14(-02) CSA C22.2 LR31928

Mounting Heights with Sockets (Unit: mm)

Front-mounting Sockets
Screw terminal Push-In Plus Terminal Block Sockets
(PYFZ-@ (-E), PYF@A (-E), PYF@A-N, PYF14-ES@-B) (PYF-@-PU)
MY
MY
MY

MY
80 82
70 (87) 66 (83) 67.5 63.1
61
42.5 28.1
27

PYF-@-PU （3.9）
PYFZ-@(-E)
PYF14-ESN-B PYF14-ESS-B
PYF@A-(@)

Note: 1. The PYF@A can be mounted on a track or with screws.

2. The heights given in parentheses are the measurements
for 53-mm-high Relays.

Back-mounting Sockets
Solder terminals/Wrapping terminals Relays with PCB Terminals
(PY@) (PY@-02)

39 (56) MY MY
48.2

PY@

PY@-02

26
 MY(S)

Dimensions (Unit: mm)

Note: All units are in millimeters unless otherwise indicated.
Terminal arrangement/
Socket Dimensions Internal connections Mounting holes
(top view)

PYF-08-PU 71.5

A1 A2
(13) (14)
Two M3 screw
67.5 holes or
30.8 two 3.5-dia. holes
28.1 108
(4.2) 25.6

12 42
(1) (4)
14 44
(5) (8)
90 35.3
11 41 Note 1: Pull out the hooks
(9) (12)
to mount the Socket
with screws.
27.35 Note: The numbers in
parentheses are Note 2: DIN-rail mounting is also
traditionally used possible. Refer to page 34
3.9 25.6
31 (4.2) terminal numbers. for supporting DIN-rails.
34.3
43
52.1

PYFZ-08-E +0.2
Two, 4.2 × 5 6−0.1 Two, M3, M4, or 4.5-dia. holes
mounting Eight, M3 × 8
holes

72 max. 35.4

(TOP VIEW)
4 Note: DIN-rail mounting is also
6 possible. Refer to page 34
23 max.
31 max. for supporting DIN-rails.

PYF08A-E +0.2
Two, 4.2 x 5 6−0.1
mounting Two, M3, M4, or 4.5-dia. holes
Eight, M3 x 8
holes

72 max.

(TOP VIEW)
Note: DIN-rail mounting is also
6 possible. Refer to page 34
23 max.
31 max. for supporting DIN-rails.

+0.2
6−0.1
PYF08A-N 42 12
Eight, M3×8 4 1
44 14
4 1 8 5
42 12

8 5

44 14 3.0 dia.

67 max. 18.7 3.5 dia. or M3

12 9
41
PYF-08A-N
11
73 41 11
12 9
14 14 13
A2 A2 A1
A2 A2 A1
Note: DIN-rail mounting is also
14 14 13
possible. Refer to page 34
Note: Figures in parentheses for supporting DIN-rails.
indicate DIN standard
22 max. 30 max. numbers.

27
 MY(S)

Terminal arrangement/
Socket Dimensions Internal connections Mounting holes
(top view)

Two, M3, M4, or 4.5-dia. holes

PYFZ-08 Two, 4.2 × 5 6+0.2
–0.1

mounting holes 8-M3 × 8

72 max. 35.4

4 (TOP VIEW)
6 Note: DIN-rail mounting is also
23 max.
possible. Refer to page 34
30 max.
for supporting DIN-rails.

PYF08A Two, 4.2 × 5 6+0.2

−0.1 3.4
mounting holes Eight, M3×8 Two, M3, M4, or 4.5-dia. holes

72 max. 35.4

(TOP VIEW)
4 Note: DIN-rail mounting is also
possible. Refer to page 34
6 for supporting DIN-rails.
23 max.
30 max.

PYF-14-PU 71.5

A1 A2
(13) (14)

Two M3 screw
67.5 holes or
30.8 two 3.5-dia. holes
28.1 108
(4.2) 25.6

12 22 32 42
(1) (2) (3) (4)

14 24 34 44
90 (5) (6) (7) (8)
35.3
Note 1: Pull out the hooks
11 21 31 41
(9) (10) (11) (12)
to mount the Socket
with screws.
27.35
Note: The numbers in Note 2: DIN-rail mounting is also
parentheses are possible. Refer to page 34
3.9
31 (4.2) 25.6 traditionally used for supporting DIN-rails.
34.3 terminal numbers.
43
52.1

PYFZ-14-E Two, 4.2 x 5 +0.2

6−0.1 Fourteen, M3 x 8 Two, M3, M4, or 4.5-dia. holes
mounting sems screws
holes

72 max. 35.4

(TOP VIEW)
4
Note: DIN-rail mounting is also
6 possible. Refer to page 34
29.5 max.
31 max. for supporting DIN-rails.

28
 MY(S)

Terminal arrangement/
Socket Dimensions Internal connections Mounting holes
(top view)

PYF14A-E
+0.2
Two, 4.2 x 5 6−0.1
Two, M3, M4, or 4.5-dia. holes
mounting
holes Fourteen, M3 x 8
sems screws

72 max.

(TOP VIEW)
6 Note: DIN-rail mounting is also
29.5 max. possible. Refer to page 34
31 max.
for supporting DIN-rails.

PYF14A-N 42 32 22 12
6+0.2
−0.1 4 3 2 1
Fourteen, M3×8 44 34 24 14
8 7 6 5 Two, 4.5 dia. or M4
4 3 2 1

42 32 22 12

8 7 6 5

44 34 24 14

67 max.
26
PYF-14A-N 12 11 10 9
41 31 21 11

12 11 10 9 73 41 31 21 11
A2 A2 A1
14 14 13 Note: DIN-rail mounting is also
14 14 13

A2 A2 A1 possible. Refer to page 34

for supporting DIN-rails.
Note: Figures in parentheses
29.5 max. 30 max.
indicate DIN standard
numbers.

PYFZ-14
Two, M3, M4, or 4.5-dia. holes
Two, 4.2 × 5 6+0.2
–0.1
mounting holes
14-M3 × 8

72 max. 35.4

4 (TOP VIEW)
6 Note: DIN-rail mounting is also
29.5 max.
30 max. possible. Refer to page 34
for supporting DIN-rails.

PYF14A Two, 4.2 × 5 6+0.2

−0.1 3.4 Two, M3, M4, or 4.5-dia. holes
mounting holes
Fourteen, M3×8

72 max. 35.4

4 (TOP VIEW)
6 Note: DIN-rail mounting is also
29.5 max.
possible. Refer to page 34
16.5
30 max.
for supporting DIN-rails.

29
 MY(S)

Terminal arrangement/
Socket Dimensions Internal connections (top view)/
mounting holes

PYF14-ESN-B
27 42.5
Label
27
9

NO
Relay
NC
4.45 4.45 4.45
82 75
3.2 4.1
6.3
PYC-35-B 6.4

COIL
COM.
24
22.5 Module
53

80

PYF14-ESS-B 27
61
9

COM.

NO

NC
4.45 4.45 4.45
83 3.2 75 4.1
6.3
PYC-35-B 6.4

COIL
29
22.5
55
82

30
 MY(S)

Terminal arrangement/
Socket Dimensions Internal connections Mounting holes
(top view)

PY08/PY08-Y1 (See note) Eight, 3 x 1.2 elliptical holes

25.5 max.
29.5 max.

20 max. 24 max.
42 max.

Note: The PY08-Y1 includes sections indicated by

dotted lines.

PY08QN/
PY08QN-Y1
(See note) 29.5 max.

22 max.
41.5 max.
24 max.
42 max.

Note: The PY08QN-Y1 includes sections

indicated by dotted lines.

PY08-02

25.5 max.
29.5 max.

22 max. Eight, 1.3-dia.

16.5 max. holes

PY14/PY14-Y1
(See note) Fourteen, 3 x 1.2 elliptical holes

25.5 max.
29.5 max.

20 max. 24 max.
42 max.

Note: The PY14-Y1 includes sections indicated by

dotted lines.

PY14QN/
PY14QN-Y1
(See note)

29.5 max.

41.5 max.

42 max. 22 max.
24 max.

Note: The PY14QN-Y1 includes sections

indicated by dotted lines.

PY14-02

25.5 max.
29.5 max.

22 max.
16.5 max. Fourteen, 1.3-dia.
holes

Note: Use a panel with plate thickness of 1 to 2 mm for mounting the Sockets.

31
 MY(S)

Short Bars for Relay Sockets and PYFZ/PYF Sockets

Short Bars for crossover wiring within one Socket or between Sockets
Applicable No. of
Application Pitch
model
Appearance and dimensions (mm) L (Length) poles
Model * Specifications

L
3.90 15.1 2 PYDN-7.75-020@

For Contact 22.85 3 PYDN-7.75-030@

7.75
terminals 18.5
mm 30.6 4 PYDN-7.75-040@
(common) 12

2.25 1.57 154.6 20 PYDN-7.75-200@ Max. carry current: 20 A

PYF-@-PU
Minimum order: 10
3.90

For Coil 31.0 18.5

12 224.35 8 PYDN-31.0-080@
terminals mm

2.25 1.57
224.35

* Replace the box (@) in the model number with the specification code for the covering color. B: Black, S: Blue, R: Red
Note: When using short bar to coil terminals of PYF-@@-PU, make sure to use PYDN-31.0-080@ (31mm).

Short Bars for within the Same Socket

Applicable No. of
Pitch Appearance Dimensions (mm) Model * Specifications
model poles
7

Max. carry current: 20 A (18 A at 70°C)

2 PYD-020B@
Ambient operating temp.: -40 to 70°C (with no
3.2 icing or condensation)
7 PYFZ-14 5.6 Ambient operating humidity: 45% to 85% (with
mm PYF14A no icing or condensation)
7 7
Conductor material: Brass
Conductor surface treatment: Nickel plating
3 PYD-030B@
Qty per package: 50/bag
3.2
5.6

* Replace the box (@) in the model number with the specification code for the covering color. B: Black, Y: Yellow

Short Bars for Adjacent Sockets

Applicable No. of
Pitch Appearance Dimensions (mm) Model * Specifications
model poles

22 40°

Max. carry current: 20 A (18 A at 70°C)

2 PYD-025B@
Ambient operating temp.: -40 to 70°C (with no
3.3 icing or condensation)
22 PYFZ-08
5.6 Ambient operating humidity: 45% to 85% (with
mm PYF08A 154 no icing or condensation)
40°
22 Conductor material: Brass
8 PYD-085B@ Conductor surface treatment: Nickel plating
Qty per package: 10/bag
3.3
5.6

29 40°

Max. carry current: 20 A (18 A at 70°C)

2 PYD-026B@ Ambient operating temp.: -40 to 70°C (with no
icing or condensation)
3.3
29 PYFZ-14 5.6 Ambient operating humidity: 45% to 85% (with
mm PYF14A no icing or condensation)
203 40°
29 Conductor material: Brass
8 PYD-086B@ Conductor surface treatment: Nickel plating
Qty per package: 10/bag
3.3
5.6

* Replace the box (@) in the model number with the specification code for the covering color. B: Black, S: Blue, R: Red

32
 MY(S)
Safety Precautions
Maximum Carry Current
• Do not allow the total current for all shorted contact form to exceed the maximum carry current of the Short Bar.
• Do not exceed the maximum carry current of the relay contacts for individual contact form.
• If you use more than one Socket, use End Plates (PFP-M).

Hold-down Clips
PYC-A1 PYC-E1 For sockets PYF14-ESN/-ESS
(2 pcs per set) (2 pcs per set)
Model Description
Metal spring clip (Used with
PYC-0
Relay only)
Plastic holding clip (Used with
36.3 36.3 PYC 35
Relay only)
PYC TR1 Thermoplastic writable label
Note: For total dimensions with plastic clip please
refer to drawings of the sockets.
4.5 5.75
4.25
4.5 1.2 4.5±0.1

PYC-P PYC-1 Y92H-3

5 5 max.
9.4

28
29 max.
3.3
53

38.5 52 58.2

4.5
4.5 1.2

Terminal Covers for PYFZ-08/PYFZ-14 Sockets

PYCZ-C08 PYCZ-C14
(for PYFZ-08) (for PYFZ-14)
0 12.6
22 -0.1 11.6 71

0
21.2 29 -0.1

Dimensions with terminal cover (Unit: mm)

PYCZ-C08 PYCZ-C14

72 max.
72 max.

34 max.
33 max. 29.5 max.
23 max.

33
 MY(S)

Mounting Plates for Back-connecting Sockets

PYP-1 PYP-36
Two, 3.4-dia. holes

72 elliptical holes

t=1.6
PYP-18

72 elliptical holes

DIN-rails and Accessories

Supporting DIN-rails
PFP-50N/PFP-100N
7.3±0.15
4.5

35±0.3 27±0.15
1
15 25 25 25 25 15 (5)
10 10
1000 (500) *

Note: The figure in the parentheses is for PFP-50N.

PFP-100N2
16
4.5
35±0.3 27 24 29.2

15 25 25 25 10 25 15 1 1.5
10 1000

Spacer
End Plate
PFP-S
PFP-M
16
10
5 12
M4 x 8 pan head screw 6.2
1.8

1
34.8
50 35.5 35.3 44.3
1.8

11.5

10 1.3
16.5
M4 spring washer 4.8

34
 MY(S)
Safety Precautions
Refer to the Common Relay Precautions.
Refer to Products Related to Common Sockets and DIN Tracks for precautions on the applicable Sockets.
Refer to PYF-@@-PU/P2RF-@@-PU for precautions on Push-In Plus Terminal Block Sockets.
Precautions for Correct Use
Handling
For models with a built-in operation indicator, models with a built-in diode, or
high-sensitivity models, check the coil polarity when wiring and wire all
connections correctly (DC operation).

Installation
• There is no specifically required installation orientation, but make sure that
the Relays are installed so that the contacts are not subjected to vibration or
shock in their movement direction.

• Use two M3 screws to attach Flange-mounted models (MY@F) and tighten the
screws securely (tightening torque: 0.98 N•m).

Using MY-series Relays with Microloads with

Infrequent Operation
If any standard MY-series Relays (e.g., MY4) are used infrequently to switch
microloads, the contacts may become unstable and eventually result in poor
contact. In this case, we recommend using the MY4Z-CBG Series, which has
high contact reliability for microloads (Refer to page 15.)

About the Built-in Diode and CR Elements

The diode or CR element that are built into the Relay are designed to absorb
the reverse voltage from the Relay coil. If a large surge in voltage is applied to
the diode or CR element from an external source, the element will be destroyed.
If there is the possibility of large voltage surges that could be applied to the
elements from an external source, take any necessary surge absorption
measures.

Latching Levers
• Turn OFF the power supply when operating the latching lever. After you use
the latching lever always return it to its original state.
• Do not use the latching lever as a switch.
• The latching lever can be used for 100 operations min.

Relay Replacement
To replace the Relay, turn OFF the power supply to the load and Relay coil
sides to prevent unintended operation and possible electrical shock.

35
OMRON AUTOMATION AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • automation.omron.com

OMRON CANADA, INC. • HEAD OFFICE OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • automation.omron.com São Paulo, SP, Brasil • 55 11 5171-8920 • automation.omron.com

OMRON ELECTRONICS DE MEXICO • HEAD OFFICE OMRON ARGENTINA • SALES OFFICE

Ciudad de México • 52.55.5901.4300 • 01.800.386.6766 • [email protected] Buenos Aires, Argentina • +54.11.4521.8630 • +54.11.4523.8483
[email protected]
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
San Pedro Garza García, N.L. • 81.12.53.7392 • 01.800.386.6766 • mela@omron. OTHER OMRON LATIN AMERICA SALES
com +54.11.4521.8630 • +54.11.4523.8483 • [email protected]

OMRON ELECTRONICS DE MEXICO • SALES OFFICE

Eugenio Garza Sada,León, Gto • 01.800.386.6766 • [email protected]

Authorized Distributor: Controllers & I/O

• Machine Automation Controllers (MAC) • Motion Controllers
• Programmable Logic Controllers (PLC) • Temperature Controllers • Remote I/O
Robotics
• Industrial Robots • Mobile Robots
Operator Interfaces
• Human Machine Interface (HMI)
Motion & Drives
• Machine Automation Controllers (MAC) • Motion Controllers • Servo Systems
• Frequency Inverters
Vision, Measurement & Identification
• Vision Sensors & Systems • Measurement Sensors • Auto Identification
Systems
Sensing
• Photoelectric Sensors • Fiber-Optic Sensors • Proximity Sensors
• Rotary Encoders • Ultrasonic Sensors
Safety
• Safety Light Curtains • Safety Laser Scanners • Programmable Safety Systems
• Safety Mats and Edges • Safety Door Switches • Emergency Stop Devices
• Safety Switches & Operator Controls • Safety Monitoring/Force-guided Relays
Control Components
• Power Supplies • Timers • Counters • Programmable Relays
• Digital Panel Meters • Monitoring Products
Switches & Relays
• Limit Switches • Pushbutton Switches • Electromechanical Relays
• Solid State Relays
Software
• Programming & Configuration • Runtime

J199I-E3-06 Note: Specifications are subject to change. © 2020 Omron. All Rights Reserved. Printed in U.S.A.

Printed on recycled paper.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Omron:
PYFZ-08 PYFZ-14 PYFZ-08-E PYFZ-14-E