Scribd
Upload
214 views35 pages

1 Deflection Diagrams and The Elastic Curve 1

This document discusses the integration method for determining the slope and deflection of beams. It provides instructions on using this method, which involves drawing an exaggerated view of the beam's elastic curve, establishing x-y coordinates, expressing the internal moment as a function of x for different load regions, integrating twice to determine slope and deflection equations, and using boundary conditions to determine constants and solve for specific values. The method assumes small deflections and neglects additional deflection from shear. An example problem is given to calculate maximum deflection for a simply supported floor joist under uniform loading.

Uploaded by

Darwin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
214 views35 pages

1 Deflection Diagrams and The Elastic Curve 1

This document discusses the integration method for determining the slope and deflection of beams. It provides instructions on using this method, which involves drawing an exaggerated view of the beam's elastic curve, establishing x-y coordinates, expressing the internal moment as a function of x for different load regions, integrating twice to determine slope and deflection equations, and using boundary conditions to determine constants and solve for specific values. The method assumes small deflections and neglects additional deflection from shear. An example problem is given to calculate maximum deflection for a simply supported floor joist under uniform loading.

Uploaded by

Darwin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 35

ce132p structural theory 2

1-1
 Deflection of structures can occur from various
sources such as
 Loads
 Temperatures
 Fabrication errors
 Settlement
 Represents the elastic curve for the points at centroids of the cross-
sectional area along each of the members
1.
2.
3.
M

A B C D
4.
P

A B C D
5.
P

A B C
6.

A B C D
1-2
1-3
 INTEGRATION METHOD used to determine the slope
and deflection of a beam.
 Elastic deformation – beam’s slope is very small
 Only deflection due to bending
 Additional deflection due to shear generally represents few
percent of the bending deformation.
1. Draw an exaggerated view of the beam’s elastic curve. Recall that
points of zero slope and zero displacement occur at fixed support,
and zero displacement occurs at pin and roller supports.
2. Establish the x and y coordinate axes. The x-axis must be parallel
to the undeflected beam and its origin at the left side of the beam,
with a positive direction to the right.
3. If several discontinuous loads are present, establish x-coordinates
that are valid for each region of the beam between the
discontinuities.
4. In all cases, the associated positive y-axis should be directed
upward.
 For each region in which there is an x-coordinate, express the

internal moment M as a function of x.

 Always assume that M acts in the positive direction when applying

the equation of the moment equilibrium to determine M = f(x).


 Provided EI is constant, apply the moment equation EI d2y/dx2 =
M(x), which requires two integrations. For each integration it is
important to include a constant of integration. The constants are
determined using the boundary conditions for the supports and the
continuity conditions that apply to slope and displacements at points
where two functions meet.
 Once the integration constants are determined and substituted back
into the slope and deflection equations, the slope and displacement
at specific points on the elastic curve can be determined. The
numerical values obtained can be checked graphically by
comparing them with the sketch of the elastic curve.
 Positivevalues for slope are counterclockwise and positive
displacement is upward.
Each simply supported floor
joist shown in the photo is
subjected to a uniform design
loading of 4 kN/m. Determine
the maximum deflection of the
joist. EI is constant.
Compute the value of EI δ at midspan for the beam loaded as shown. If
E = 10 GPa, what value of I is required to limit the midspan deflection
to 1/360 of the span?
NEXT TOPIC: MOMENT-AREA METHOD

You might also like