PRODUCT

OVERVIEW

JD09
In August of 1984, JST Deutschland GmbH was founded as a wholly
owned Subsidiary of J.S.T.- Mfg. Co. Ltd. Osaka/Japan, established in
1957. At the beginning only loose piece terminals were being
manufactured and distributed, today JST manufactures and sells all over
the world connectors into the Consumer Electronics, Telecommunication,
Medical, Camera Industry, Computers.

Since 1993 J.S.T. is developing connectors especially for the automotive

market and their system supplier. With a special intern organization (the
J.S.T.-Automotive Group) J.S.T. will support the automotive market
much better in case of design and service. Beside the known quality
standards, the J.S.T.-Automotive Group is a competent and strong
partner for design and development of special customer solutions and
future oriented technologies.

JST Deutschland GmbH

Küferstr. 15
D-73650 Winterbach
Switchboard: +49 / 71 81 / 40 07 – 0
Telefax: +49 / 71 81 / 40 07 – 21
e-Mail: [email protected]
Internet: www.jst.de

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

1
 Page
Wire to Board connectors – CRIMP 3-9
Potting Type connectors - Wire to Board – CRIMP 10
High Voltage connectors - Wire to Board – CRIMP 11

Power / Signal Connectors 11

Wire to Board connectors - IDC 12 – 13
Ribbon Cables and Pin Header connectors 14
Wire to Wire connectors – CRIMP 15 – 18
High Voltage connectors - Wire to Wire – CRIMP 18
Waterproof Connectors 19
LED connectors 20
Board-in connectors – CRIMP 21
Board-in connectors – IDC 22
SMT Socket spring 22
Board to Board connectors 23 – 24
FFC/FPC connectors 25 – 29
Coaxial connectors 29
Interface connectors 30
Loose Piece and Chain Terminals 31
Tooling Service 31
Harness Production 31
INDEX – Connector series name in alphabetical order 33

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

2
 Wire to Board connectors - CRIMP
Connector Series Specifications Remarks

30V / 1A*
pitch 0.8 mm
2-20 circuits dimensions (e.g. 3 circuits)
SUH
AWG 32 to AWG 28 TOP entry 4.6x1.95x4.15
SIDE entry 4.6x4.1x1.75
SMT headers SUR - IDC

pitch 1.0 mm
50V / 1A* SH – single row
2-20 circuits (SH) SHD – double row
SH dimensions SH (e.g. 3 circuits)
20-50 circuits (SHD)
SHD TOP entry 5.0x2.9x6.3
AWG 32 to AWG 26 SIDE entry 5.0x6.25x2.95
SMT dimensions SHD (e.g. 20circuits)
TOP entry 12.3x5.4x6.3
SIDE entry 12.3x7.1x5.5

50V / 1A*
2-15 circuits pitch 1.0 mm
NSH New NSHD: 16, 20, 28 dimensions (e.g. 9 circuits)
TOP entry 11x4.4x7.8
NSHD Double-row type SIDE entry 11x7.65x4.5
AWG 32 to AWG 28 locking system
SMT

50V / 1A*
2-30 circuits pitch 1.0 mm
SHL dimensions (e.g. 6 circuits)
AWG 32 to AWG 28 SIDE entry 8.8x7.2x1.8
SMT headers side entry

50V / 1A* pitch 1.0 mm

20-50 circuits dimensions (e.g. 30 circuits)
SHLD TOP entry 18.0x5.8x7.3
AWG 32 to AWG 28 SIDE entry 18.0x9.05x6.15
SMT locking system

30V / 1A* pitch 1.0 mm

21 and 31 circuits dimensions (e.g. 21 circuits)
SHLV TOP entry 15.0x5.0x7.95
AWG 32 to AWG 28 SIDE entry 15.0x8.5x5.15
SMT locking system

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

3
Connector Series Specifications Remarks

50V / 2A*/2.5A* pitch 1.2 mm

ACH
2-6 circuits high box type available
ACHF
AWG 30 to AWG 28 dimensions (e.g. 3 circuits ACH)
ACHL TOP entry 5.4x4.3x1.4
SMT

50V / 1A*
pitch 1.25 mm
3 circuits dimensions (e.g. 3 circuits)
AGH
AWG 30 to AWG 26 TOP entry 5.8x6.2x4.4
TOP entry high box: 5.8x6.2x6.1
SMT top entry
2 different headers

50V / 1A*
2-15 circuits pitch 1.25 mm
dimensions (e.g. 3 circuits)
GH AWG 30 to AWG 26 TOP entry 7.0x4.25x7.3
SMT SIDE entry 7.0x7.15x4.35
locking system

50V / 1A* pitch 1.25 mm

2-15 circuits dimensions (e.g. 3 circuits)
GVH SIDE feed 5.0x8.75x8.7
AWG 30 to AWG 26 SIDE entry 7.0x7.15x5.6
SMT locking system

50V / 1A* pitch 1.25 mm

20, 22, 30 and 40 circuits double row
GHD AWG 30 to AWG 26 dimensions (e.g. 20 circuits)
TOP entry 15.75x8.5x8.05
SMT SIDE entry 15.75x9.35x8.55
locking system

30V / 3A* pitch 1.3 mm

3 circuits Power Supply connector
dimensions
ADH AWG 28 to AWG 26 height 1.9 mm
SMT width 4.3 mm

pitch 1.5 mm
50V / 1A* >> JST highrunner <<
dimensions (e.g. 3 circuits)
2-13 circuits SMT
ZH TOP entry 7.5x3.7x6.1
AWG 32 to AWG 26 SIDE entry 7.5x6.0x3.7
SMT and THT THT
TOP entry 6.0x3.5x5.6
SIDE entry 6.0x7.1x3.7

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

4
Connector Series Specifications Remarks

pitch 1.5 mm
100V / 2A* dimensions (e.g. 4 circuits)
SMT
CZ 2-40 circuits TOP entry 9.0x4.9x7.8
family AWG 28 to AWG 26 SIDE entry 9.0x4.9x7.8
THT
SMT and THT TOP entry 9.0x4.4x7.3
SIDE entry 9.0x9.8x4.4

pitch 1.5 mm
100V / 2A* dimensions (e.g. 3 circuits)
2-16 circuits SMT
TOP entry 9.0x5.8x9.4
ZE AWG 30 to AWG 24 SIDE entry 9.0x9.4x5.8
SMT and THT THT
TOP entry 7.5x5.75x10.4
SIDE entry 7.5x9.7 x6.3
locking system

100V / 2A* pitch 1.5 mm

10-40 circuits double row
ZPD AWG 28 to AWG 24 dimensions (e.g. 20 circuits)
TOP entry 18.7x8.6 x9.5
SMT SIDE entry 18.7x10.5x9.2
locking system

350V / 4A*
2 circuits pitch 1.8 mm
dimensions
SFH AWG 30 to AWG 22 5.2x8.2x3.0
SMT
(LED application)

pitch 2.0 mm
PH – single row/+HighBox
100V / 2A*/3A*(PHD)
PHD – double row
2-16 circuits (PH)
PH >> JST highrunner <<
8-34 circuits (PHD) dimensions PH SMT(e.g. 3 circuits)
PHD
AWG 32 to AWG 24 (22) TOP entry 9.95x5.0x8.6
SIDE entry 9.9 x9.6x5.5
SMT and THT dimensions PHD THT(e.g. 20circuits)
TOP entry 21.9x5.0 x8.8
SIDE entry 21.9x11.8x5.0
pitch 2.0 mm
product family
250V / 3A* Crimp and IDC
2-16 circuits WtB and WtW
AWG 28 to AWG 22 >> JST highrunner <<
PA dimensions (e.g. 3 circuits)
SMT and THT SMT
TOP entry 10.0x6.2 x11.1
SIDE entry 10.0x11.1x 6.2
THT
TOP entry 8.0x5.8 x9.8
SIDE entry 8.0x13.8x7.0
locking system

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

5
Connector Series Specifications Remarks

100V / 3A* pitch 2.0 mm

2-15 circuits SPHD terminals
PBV AWG 28 to AWG 22 PCB layout PA
dimensions (e.g. 4 circuits)
SMT TOP entry 11.0x8.2 x12.1
SIDE entry 11.0x13.2x 6.85
locking system

pitch 2.0 mm
250V / 3A* double row
dimensions (e.g. 20 circuits)
10-40 circuits TOP entry 22.0x10.0x12.4
PAD SIDE entry 22.0x15.4x11.0
AWG 28 to AWG 22 locking system
THT

pitch 2.0 mm
250V / 3A* double row
8-40 circuits dimensions (e.g. 20 circuits)
PND TOP entry 22.0x11.7x12.9
AWG 28 to AWG 22 locking system
THT

100V / 3A*
pitch 2.0 mm
2-10 circuits dimensions (e.g. 3 circuits)
PNI AWG 28 to AWG 22 TOP entry 8.0x6.65x12.25
inner locking system
THT

100V / 3A*
pitch 2.0 mm
2-10 circuits dimensions (e.g. 3 circuits)
PLI AWG 28 to AWG 22 TOP entry 7.7x7.15x9.6
inner locking system
THT

pitch 2.0 mm
250V / 3A* double row
dimensions (e.g. 20 circuits)
8-40 circuits SMT
PUD TOP entry 24.0x8.8 x12.3
AWG 28 to AWG 22 THT
SMT and THT TOP entry 22.0x8.7 x11.0
SIDE entry 220x14.1x 8.9
locking system

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

6
Connector Series Specifications Remarks

125V / 6.2A* pitch 2.2 mm

3-30 circuits single and double row
JFA locking system
AWG 28 to AWG 18
J1000
THT

pitch 2.5 mm
250V / 3A*
2-15 circuits >> JST highrunner <<
EH dimensions (e.g. 3 circuits)
AWG 32 to AWG 22 (20) TOP entry 10.0x3.8 x8.1
THT SIDE entry 10.0x10.3x4.2

pitch 2.5 mm
250V / 3A* high box type available
1-20 circuits >> JST highrunner <<
XH AWG 30 to AWG 22 dimensions (e.g. 3 circuits)
SMT
SMT and THT SIDE entry 12.5x10.3x6.0
BtB => JQ THT
TOP entry 9.9x5.75 x9.8
SIDE entry 9.9x14.3 x6.1

250V / 3A* pitch 2.5 mm

8-40 circuits double row
XAD AWG 28 to AWG 20 dimensions (e.g. 20 circuits)
TOP entry 30.0x11.5x13.8
THT SIDE entry 30.0x19.9x13.5
locking system

250V / 3A*
2-20 circuits pitch 2.5 mm
AWG 28 to AWG 20 +HighBox
XA SMT and THT >> JST highrunner <<
Glow Wire version acc. dimensions (e.g. 3 circuits)
TOP entry 9.8x6.9 x19.5
IEC60695-2-10/11 locking system
available

250V / 4.6A* pitch 2.5 mm

JFA 6-20 circuits single and double row
J2000 AWG 28 to AWG 20 locking system
THT

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

7
Connector Series Specifications Remarks
250V / 3A*
2-15 circuits pitch 2.5 mm
XNI AWG 30 to AWG 22 dimensions (e.g. 3 circuits)
TOP entry 10.0x7.95x12.6
THT locking system

250V / 3A*
2, 3 and 6 circuits pitch 2.5 mm
PXA AWG 26 to AWG 22 dimensions (e.g. 3 circuits)
TOP entry 10.0x8.95x20.5
THT high box locking system

250V / 3A*
5 circuits pitch 2.5 mm
XAG AWG 24 to AWG 20 low profile: height: 5 mm
SMT locking system

250V / 3A*
2-10 circuits pitch 2.5 mm
XM AWG 28 to AWG 20 dimensions (e.g. 5 circuits)
TOP entry 14.9x8.9x20.0
THT high box locking system

250V / 3A*
2-25 circuits pitch 2.5 mm
dimensions (e.g. 5 circuits)
NH AWG 30 to AWG 22 TOP entry 16.2x6.5x14.9
THT side / top and SIDE entry 16.2x17.7x6.5
BOTTOM entry 16.2x12.2x14.7
bottom entry type
300V / 4A*
2-12 circuits pitch 3.3 mm
BNI AWG 24 to AWG 20 single row (2+3 circuits)
double row (4-12 circuits)
THT / potting area max. 10 mm secure inner locking system

pitch 3.81 mm / 5.08 mm

250V/600V / 15A* single, double and triple
JFA 1-20 circuits row, module type
J300 AWG 28 to AWG 14 locking system
THT

pitch 3.96 mm
250V / 10A* high box type available
2-11 circuits >> JST highrunner <<
VH dimensions (e.g. 3 circuits)
AWG 22 to AWG 16 TOP entry 11.82x10.5x16.5
THT SIDE entry 11.82x20.5x10.5
locking system

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

8
Connector Series Specifications Re m a r k s
300V / 7A* pitch 3.96 mm
4-12 circuits double row
HL
AWG 22 to AWG 18 locking system
THT
300V / 12A* pitch 4.0 mm
2-14 circuits single and double row
PSI 3 key patterns and colours
AWG 16 to AWG 26 locking system
THT

300V / 7A*
pitch 5.0 mm
2-6 circuits single row (2-4 circuits)
HYV
AWG 22 to AWG 18 double row (4+6 circuits)
secure inner locking system
THT / potting area max. 9 mm

250V / 10A*
pitch 5.0 mm
2-4 circuits dimensions (e.g. 3 circuits)
NV
AWG 22 to AWG 16 TOP entry 15.0x10.6x16.5
locking system
THT

150V / 10A* pitch 5.0 mm

2-16 circuits double row
XL dimensions (e.g. 4 circuits)
AWG 26 to AWG 16 TOP entry 10.0x17.7x20.1
THT locking system

250V/600V / 15A*
JFA 1-20 circuits pitch 3.81 mm / 5.08 mm
J300 AWG 28 to AWG 14 single, double and triple
THT row, module type
locking system

600V / 22A*
JFA 2-6 circuits pitch 6.0 mm / 6.35 mm
J4000 AWG 16 to AWG 12 single row
locking system
THT
600V / 20A* pitch 6.2 mm
2-12 circuits double row
VL dimensions (e.g. 4 circuits)
AWG 22 to AWG 12 TOP entry 13.4x19.3x29.2
THT locking system

600V / 35A* pitch 8.8 mm

JFPS 2 circuits 2 different keying/ colours available
dimensions
AWG 12 to AWG 10 height: 30.0 mm
THT width: 14.4 mm
locking system

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

9
Potting Type connectors - Wire to Board – CRIMP

Connector Series Specifications Re m a r k s

PA 250V / 3A* pitch 2.0 mm
locking system
high 2-15 circuits THT header height 13.9 mm
box AWG 28 to AWG 22
PH 100V / 2A* pitch 2.0 mm
high 2-13 circuits THT header height 15 mm
box AWG 30 to AWG 24
100V / 3A*
pitch 2.0 mm
2-10 circuits locking system
PNI
High box: 2-15 circuits THT header height 10.2 mm
High box: 16.4 mm
AWG 28 to AWG 22
100V / 3A*
10-30 circuits pitch 2.0 mm
PID locking system
double row type THT header height 9.7 mm
AWG 26 to AWG 22
250V / 3A* pitch 2.5 mm
XNI 2-15 circuits locking system
AWG 30 to AWG 22 THT header height 10.6 mm

250V / 3A* pitch 2.5 mm

PXA 2, 3 and 6 circuits locking system
AWG 26 to AWG 22 THT header height 17 mm

XH 250V / 3A*
high 2-10 circuits pitch 2.5 mm
THT header height 14.2 mm
box AWG 30 to AWG 22

XA 250V / 3A* pitch 2.5 mm

high 2-15 circuits locking system
box AWG 28 to AWG 22 THT header height 17 mm

300V / 4A*
2-12 circuits pitch 3.3 mm
BNI AWG 24 to AWG 20 single row (2+3 circuits)
double row (4-12 circuits)
THT / potting area max. 10 mm secure inner locking system

300V / 7A* pitch 5.0 mm

HYV 2-6 circuits single row (2-4 circuits)
double row (4+6 circuits)
AWG 22 to AWG 18 secure inner locking system
THT / potting area max. 9 mm
300V / 15A* pitch 6.5 mm
VYH 2-6 circuits locking system
AWG 26 to AWG 14 THT header height 15.5 mm

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

10
 High Voltage connectors - Wire to Board - CRIMP

Connector Series Specifications Remarks

1400 V / 1A* pitch 3.5 mm

2 circuits High voltage
BHS dimensions
AWG 28 to AWG 24 SIDE entry 7.5x113.9x3.2
SMT locking system

600V / 1A*
2-5 circuits pitch 4.0 – 8.0 – 12.0 mm
BH High voltage
AWG 28 to AWG 22 locking system
SMT and THT

pitch 3.5 mm
1400 V / 1A* pitch 13.0 mm
3000 V / 1A* High voltage
BD 2 circuits dimensions SMT
AWG 28 to AWG 24 SIDE entry 7.5x14.0x5.0
dimensions THT
SMT and THT SIDE entry 7.5x14.5x5.0
locking system

Power / Signal Connectors

Connector Series Specifications Remarks

Pitch:
50 V / 0.5A/7A*
Power: 3.45 / 5.45 / 7.45 /
3, 5, 7 and 9 circuits
LBT 9.45 mm
AWG 28 to AWG 20
Signal: 1.0 mm
SMT

30V / 1A/5A* pitch 1.85 mm

3 and 5 circuits dimensions:
AUH height: 1.85
AWG 30 to AWG 22 depth: 5.2
SMT

100V/300V
2A (AWG 24) /45A (AWG 8)*
Secure double-locking
JFX 2 power / 16 signal lines
system
wire-to-wire

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

11
 Wire to Board connectors - IDC
Connector Series Specifications Re m a r k s

30V / 0.2A*
2-22 circuits pitch 0.6 mm
XSR dimensions (e.g. 4 circuits)
AWG 36 SIDE entry 4.2x3.0x1.45
SMT

30V / 0.5A*
2-22 circuits
pitch 0.8 mm
AWG 36 and AWG 32 dimensions (e.g. 3 circuits)
SUR
SMT TOP entry 3.2x2.25x3.95
SIDE entry 3.2x3.9 x1.75

50V / 0.7A* pitch 1.0 mm

dimensions (e.g. 3 circuits, SR)
SR/SZ 2-14 circuits TOP entry 4.0x2.9 x4.9
SSR AWG 30 / AWG 32 SIDE entry 4.0x4.85x2.95
dimensions (e.g. 3 circuits, SSR)
SMT / THT SIDE entry 4.0x4.5x2.0

50V / 0.7A*
2-4 circuits
pitch 1.0 mm
ASR AWG 30 dimensions (e.g. 3 circuits, ASR)
SMT 5.4x3.5x3.6
Header top entry
Housing side entry

50V / 1.8A*
3-31 circuits
pitch 1.0 mm
AWG 27/AWG 28 dimensions (e.g. 5 circuits)
CS
Top entry THT 9.0x6.7x11.9
locking system
WtW unit

pitch 1.5 mm
50V / 0.7A* dimensions (e.g. 3 circuits)
SMT
2-13 circuits TOP entry 7.5x3.7x6.0
ZR
AWG 30 and AWG 28 SIDE entry 7.5x7.1x3.7
THT
SMT and THT TOP entry 6.0x3.5x5.5
SIDE entry 6.0x7.0x3.7

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

12
Connector Series Specifications Re m a r k s
pitch 1.5 mm
100V / 2A* dimensions (e.g. 4 circuits)
SMT
2-40 circuits TOP entry 9.0x4.9x7.8
CZ family
AWG 28 and AWG 26 SIDE entry 9.0x4.9x7.8
THT
SMT and THT TOP entry 9.0x4.4x7.3
SIDE entry 9.0x9.8x4.4

50V / 0.7A*
2-40 circuits pitch 1.5 mm
dimensions (e.g. 10 circuits)
ZF/ZFW AWG 28 TOP entry 16.5x6.6x15.1
THT SIDE entry 18.0x17.8x7.2
locking system
double-row top entry
pitch 2.0 mm
250V / 3A* Crimp and IDC
2-16 circuits WtB and WtW
AWG 28 to AWG 22 >> JST highrunner <<
PA dimensions (e.g. 3 circuits)
SMT and THT SMT TOP entry 10.0x6.2 x11.1
SMT SIDE entry 10.0x11.1x 6.2
THT TOP entry 8.0x5.8 x9.8
THT SIDE entry 8.0x13.8x7.0
locking system
100V / 1A* pitch 2.0 mm
2-16 circuits dimensions (e.g. 3 circuits)
KR AWG 28 and AWG 26 SMT (KR)
TOP entry 8.0x5.0x7.5
KRD SMT and THT SIDE entry 8.0x8.5x5.5
KR - end connection THT (KR)
KRD - through connection TOP entry 8.0x4.8x6.9
SIDE entry 8.0x8.5x4.8
(daisy chain)
250V / 2A*
2-16 circuits pitch 2.5 mm
dimensions (e.g. 3 circuits)
NR AWG 28 / AWG 26 and TOP entry 10.0x7.0x13.1
SIDE entry 10.0x17.6x6.1
NRD AWG 24
NR - end connection
THT => XH
NRD - through connection
BtB => JQ
(daisy chain)

250V / 7A* pitch 3.96 mm

2-15 circuits dimensions (e.g. 3 circuits)
AWG 26 / AWG 24 / AWG 22 / TOP entry 11.88x9.2x20.88
VR AWG 20 / AWG 18 SIDE entry 11.88x26.85x7.75
THT side and top entry end connection
and daisy chain

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

13
 Ribbon Cables and Pin Header Connectors
Connector Series Specifications Remarks

300V / 1A*
RA pitch 2.54 mm
10-60 circuits
(IDC) locking system
THT

300V / 1A* pitch 2.54 mm

RA conform to MIL-C-83503
10-60 circuits
(CRIMP) standard
THT locking system

300V / 1A*
RC pitch 2.54 mm
10-60 circuits
(IDC) board-in
THT

250V / 2A*
RE pitch 2.54 mm
2-9 circuits
(CRIMP) single row
THT

250V / 2A*
RF pitch 2.54 mm
6-28 circuits
(CRIMP) double row
THT

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

14
 Wire to Wire connectors - CRIMP
Connector Series Specifications Remarks

50V / 1A* pitch 1.0 mm

SH / SR 3 circuits connecting adapter
New development to mate with 2 female housings

50V / 2A* pitch 1.2 mm

ACH 2 circuits dimensions
AWG 30 to AWG 28 3.8x6.8x1.85

50V / 0.7A*
2-13 circuits pitch 1.5 mm
ZM dimensions (e.g. 3 circuits)
AWG 30 to AWG 28 7.0x9.1x3.6

pitch 2.0 mm
250V / 3A* Crimp and IDC
2-16 circuits WtB and WtW
PA AWG 28 to AWG 22 dimensions (e.g. 3 circuits)
SMT TOP entry 10.0x6.2 x11.1
SMT and THT SMT SIDE entry 10.0x11.1x 6.2
THT TOP entry 8.0x5.8 x9.8
THT SIDE entry 8.0x13.8x7.0
locking system

100V / 3A* pitch 2.0 mm

PNI 2-10 circuits dimensions (e.g. 3 circuits)
8.0x21.35x6.45
AWG 28 to AWG 22 locking system

100V / 2A* pitch 2.0 mm

PH connecting adapter
2-8, 10,11 and 12 circuits to mate with 2 female housings

125V / 6.2A* pitch 2.2 mm

JFA 3-26 circuits single and double row
J1000 AWG 28 to AWG 18 locking system

250V / 4.6A* pitch 2.5 mm

JFA 3-20 circuits single and double row
locking system
J2000 AWG 28 to AWG 20

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

15
Connector Series Specifications Remarks

250V / 3A* pitch 2.5 mm

SM 2-18 circuits dimensions (e.g. 3 circuits)
10.5x22.9x7.5
AWG 28 to AWG 22 locking system

250V / 3A*
pitch 2.5 mm
2-18 circuits dimensions (e.g. 3 circuits)
XM
AWG 28 to AWG 20 11.8x20.0x6.8
locking system

250 V / 3A*
pitch 2.5 mm
2 to 6 circuits dimensions (e.g. 3 circuits)
XMA
AWG 26 to AWG 22 14.0x27.4x9.85
inner locking system

250V / 3A*
5 circuits pitch 2.5 mm
XAG AWG 24 to AWG 20
locking system

250V / 3A*
2-15 circuits (single row) pitch 2.5 mm
dimensions (e.g. 3 circuits)
XA Glow Wire version acc. 10.0x22.7x7.1
XAD IEC60695-2-10/11 available dimensions (e.g. 20 circuits)
27.5x25.2x11.4
8-40 circuits (double row) locking system
AWG 28 to AWG 20

250V / 3A* pitch 2.5 mm

EH connecting adapter
2 - 6 circuits to mate with 2 female housings

250V / 3A* pitch 2.5 mm

XH connecting adapter
2-8, 10,11 and 12 circuits to mate with 2 female housings

pitch 3.3 mm
HIL 300V / 5A* single row: 2 + 3 circuits
2-8 circuits double row: 4, 6 + 8 circuits
dimensions (e.g. 3 circuits)
AWG 24 to AWG 18 11.9x34.6x9.0
locking system

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

16
Connector Series Specifications Remarks

250V/600V / 15A* pitch 3.81 mm / 5.08 mm

JFA 1-20 circuits single, double row
J300 AWG 28 to AWG 14 module type
locking system

pitch 3.96 mm
300V / 7A*
double row
HL 2-12 circuits dimensions (e.g. 3 circuits)
AWG 22 to AWG 18 13.12x34.2x9.5
locking system

300 V / 7A* pitch 3.96 mm

1-6 circuits single and double row
SL dimensions (e.g. 3 circuits)
AWG 26 to AWG 18 13.12x31.4x9.3
locking system

250V / 10A* pitch 3.96 mm

VH connecting adapter
2-9 circuits to mate with 2 female housings

300 V / 12A* pitch 4.0 mm

2 -3 circuits single row
PSI
AWG 26 to AWG 16 A + B type key
locking system

pitch 4.5 mm
300 V / 10A*
single, double and
1-21 circuits
YL triple row
AWG 26 to AWG 16 dimensions (e.g. 3 circuits)
14.8x38.7x10.8
locking system

300V / 10A* pitch 4.5 mm

2-6 circuits single and double row
YLN dimensions (e.g. 3 circuits)
AWG 26 to AWG 16 18.3x38.7x10.8
locking system

pitch 4.5 mm
single, double and
300V / 10A*
triple row
EL 2-15 circuits
>> JST highrunner <<
AWG 26 to AWG 16 dimensions (e.g. 3 circuits)
14.8x39.2x10.4
locking system

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

17
Connector Series Specifications Remarks

pitch 5.0 mm
300V / 10A*
single and double row
ZL 2-16 circuits dimensions (e.g. 4 circuits)
AWG 26 to AWG 16 11.7x41.8x18.2
locking system

pitch 5.0 mm
300V / 10A*
double row
XL 2-16 circuits dimensions (e.g. 4 circuits)
AWG 26 to AWG 16 11.2x30.9x11.7
locking system

JFA 250V/600V / 15A* pitch 3.81 mm / 5.08 mm

J300 1-20 circuits single, double row
AWG 28 to AWG 14 module type
locking system

pitch 6.2 mm
600V / 20A* High voltage
VL 1-12 circuits single and double row
AWG 22 to AWG 12 dimensions (e.g. 3 circuits)
19.6x44.1x12.2
locking system

High Voltage connectors - Wire to Wire - CRIMP

Connector Series Specifications Remarks

1400 V / 1A* pitch 3.5 mm

BHS 2 circuits High voltage
dimensions
AWG 28 to AWG 24 7.5x21.4x3.7

600V / 1A* pitch 4.0 and 8.0 mm

BHM 2-5 circuits High voltage
dimensions (e.g. 3 circuits)
AWG 28 to AWG 22 13.1x18.4x3.7

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

18
 Waterproof Connectors
Connector Series Specifications Remarks

12V / 7A* waterproof

1 circuit IEC 60529 IPX7
WPK 0.5 to 0.85 mm² dimensions
outer diameter 1.6 to 1.9 mm 12.2x44.0x12.2
locking system
wire to wire

100V / 3A* pitch 2.0 mm

2-8 circuits waterproof
JWPF AWG 26 to AWG 22 IEC 60529 IPX7
wire to board dimensions (e.g. 3 circuits)
TOP entry 10.0x4.1x11.3
THT locking system

100V / 3A* pitch 2.0 mm

2-8 circuits waterproof
JWPF IEC 60529 IPX7
AWG 26 to AWG 22
wire to wire locking system

300V / 6A*
2 and 4 circuits pitch 4.0 mm
JWPS AWG 22 to AWG 18 Waterproof IPX7
wire to wire and locking system
wire to board

300V / 7A* pitch 5.0 mm

2-3 circuits waterproof
WPJ AWG 22 to AWG 18 IEC 60529 IPX7
wire to board and dimensions (e.g. 3 circuits)
TOP entry 19.2x11.2x25.3
wire to wire locking system

pitch 7.0 mm
300V / 7A*
waterproof
1-2 circuits
MWP IEC 60529 IPX4
AWG 26 to AWG 18 dimensions (e.g. 2 circuits)
wire to wire 18.7x43.9x14.2
locking system

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

19
 LED Connectors
Connector Series Specifications Remarks
3A Mating height: 2.8 mm
LEK single circuits
board to board SMT

125V / 1A* pitch 1.0 mm

6 circuits dimensions 6 circuits:
SHJ
AWG 32 to AWG 28 10.6x7.2x2.65 mm
locking system
wire to board SMT
200V / 1A* pitch 1.1 mm
5 circuits dimensions 5 circuits:
SFG
AWG 30 to AWG 28 6.75x7.0x3.48 mm
locking system
wire to board SMT
350V / 4A* pitch 1.8 mm
2 circuits dimensions 2 circuits:
SFK
AWG 30 to AWG 22 5.2x8.8x4.0 mm
locking system
wire to board SMT
350V / 4A*
2 circuits pitch 1.8 mm
SFH dimensions 2 circuits:
AWG 30 to AWG 22 5.2x8.2x3.0 mm
wire to board SMT

300V / 3A* pitch 1.8 mm

2 circuits SFH-contacts
LEA height: 3 mm
AWG 30 to AWG 22 locking system
wire to board SMT

300V / 1A* pitch 2.0 mm

2 circuits dimensions 2 circuits:
SFV
AWG 30 to AWG 28 4.9x7.0x7.95 mm
locking system
wire to board SMT
300V / 3A*
2 and 4 circuits pitch 2.5 mm
LEX
AWG 30 to AWG 22 locking system
wire to board – bottom type
300V / 3A* pitch 3.0 mm
2, 3 and 4 circuits low profile :
LEN
AWG 26 to AWG 22 mounting height : 3.0 mm
wire to board SMT locking system

300V / 3A* pitch 4.0 mm

dimensions 2 circuits
1 + 2 circuits 8.8x10.2x2.65
LEB
AWG 26 to AWG 22
dimensions 1 circuit
wire to board + board to board 4.8x10.2x2.65

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

20
 Board-in connectors – CRIMP

Connector Series Specifications Remarks

50V / 0.7A* pitch 1.5 mm

dimensions e.g. 5 circuits:
SZN 2-13 circuits 8.5x2.4x4.25 mm
AWG 30 to AWG 26

250V / 2A*
2-15 circuits pitch 2.0 mm
dimensions e.g. 5 circuits:
SAN AWG 30 to AWG 24 11.2x3.25x6.0 mm

250V / 3A*
2-10 circuits pitch 2.0 mm
dimensions e.g. 4 circuits:
SJN AWG 28 to AWG 22 8.4x4.9x2.8 mm

250V / 2A*
8-14 circuits pitch 2.0 mm
dimensions e.g. 8 circuits:
SGN AWG 28 to AWG 24 17.2x2.9x4.0 mm

250V / 3A*
2-16 circuits pitch 2.5 mm
dimensions e.g. 5 circuits:
SCN AWG 28 to AWG 22 14.0x3.9x6.5 mm

250V / 7A*
2-12 circuits pitch 3.96 mm
dimensions e.g. 5 circuits:
SDN AWG 22 to AWG 18 20.84x6.2x7.05 mm

SIN AWG 30 to AWG 10 single circuit

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

21
 Board-in connectors – IDC

Connector Series Specifications Remarks

50V / 0.7A* pitch 1.5 mm

2-13 circuits dimensions e.g. 5 circuits:
ZA 9.0x3.0x4.3 mm
AWG 30 and AWG 28

100V / 1.0A* pitch 2.0 mm

2-15 circuits dimensions e.g. 5 circuits:
DA 11.9x4.0x5.0 mm
AWG 28 and AWG 26

100V / 0.7A* pitch 2.0 mm

2-15 circuits dimensions e.g. 5 circuits:
DD/DS 12.0x4.3x3.5 mm
AWG 28

250V / 2A* pitch 2.5 mm

2-13 circuits dimensions e.g. 5 circuits:
DB 15.0x4.1x7.1 mm
AWG 28, AWG 26 + 24

Socket Spring – SMT

24V / 3A
Applicable for
1 circuit socket spring
SBO SMT pick and place
for pins 0.45 – 0.8 mm
2 contact points

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

22
 Board to Board connectors

Connector Series Specifications Remarks

30V / 0.3A
80, 100 and 120 circuits pitch 0.4 mm
JAS dimensions (e.g. 80 circuits)
Stacking height 4.0/4.5 TOP entry 19.0x4.2x4.0/4.5
SMT

30V
height 0.8 mm: 0.25A
pitch 0.4 mm
JADN height 1.0 mm: 0.3A
36, 44, 50 and 68 circuits
SMT

50V / 0.5A
pitch 0.5 mm
14-64 circuits dimensions (e.g. 20 circuits, h=3.0)
JMC
different stacking height TOP entry 6.9x3.4x3.0
SIDE entry 6.9x4.15x4.33
SMT

50V / 0.5A
20-100 circuits pitch 0.5 mm
JMD
different stacking height
SMT

50V / 0.5A
140 and 200 circuits
JU pitch 0.6 mm
top entry and side entry
SMT / THT

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

23
Connector Series Specifications Remarks

50V / 0.5A pitch 0.635 mm

HTB 30 and 40 circuits dimensions (e.g. 30 circuits)
TOP entry 16.0x10.4x16.0
SMT SIDE entry 16.0x17.1x9.7

50V / 1.0A pitch 1.25 mm

5-19circuits(JE, single row) dimensions (e.g. 5 circuits, JE)
JE SIDE entry 7.4x4.4x6.8
8, 16, 22 circuits
JED dimensions (e.g. 8 circuits, JED)
(JED, double rows) TOP entry 5.95x4.6x7.0
THT SIDE entry 5.95x4.6x7.0

50V / 1.0A pitch 1.27 mm

JXV 30 and 50 circuits height: 9.0 mm
SMT

250V / 1.0A
4-12 circuits
pitch 2.0 mm
top entry and side entry dimensions (e.g. 5 circuits)
MQ
low insertion force type TOP entry 12.0x5.5x9.2
SIDE entry 12.0x5.5x9.2
also available
THT

250V / 3.0A
3-15 circuits
pitch 2.5 mm
top entry and side entry dimensions (e.g. 5 circuits)
JQ
interchangeable with TOP entry 13.2x6.0x11.8
SIDE entry 13.2x16.3x6.15
headers series XH
THT

250V / 3.0A
3-15 circuits pitch 2.5 mm
JL dimensions (e.g. 5 circuits)
top entry and side entry SIDE entry 13.2x16.3x7.5
THT

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

24
 FFC / FPC Connectors
Connector Series Specifications Remarks

50V / 0.2A pitch 0.2 mm

21 to 77 circuits front flip-lock type
FVX
ZIF dimensions (e.g. 21circuits)
SMT SIDE entry 6.2x3.17x1.0

50V / 0.2A
39, 51 and 61 circuits pitch 0.2 mm
FVXS dimensions (e.g. 51 circuits)
ZIF SIDE entry 11.5x3.17x1.0
SMT

50V / 0.2A
13 to 51 circuits
ZIF pitch 0.25 mm
FGEM for FPC with protrusion dimensions
height closed: 1.4 mm
mid-flip type height open: 1.69 m
double-sided contact
SMT

50V / 0.2A
19 to 61 circuits pitch 0.3 mm
FXRH ZIF housing material LCP
dimensions
double-sided contact height: 0.9 mm
back-flip lock mechanism
SMT

50V / 0.2A pitch 0.3 mm

80 circuits Housing material LCP
FXM ZIF double ZIF structure
SMT dimensions
SIDE entry 28.7x7.55x2.9

50V / 0.2A
17-51 circuits pitch 0.3 mm
dimensions (e.g. 15 circuits)
FXS ZIF SIDE entry 7.0x3.85x1.8
gold plated contacts
SMT

pitch 0.3 mm
50V / 0.2A housing material LCP
11-61 circuits low profile 1.0 mm
FXR
ZIF front flip-lock type
SMT dimensions (e.g. 15 circuits)
SIDE entry 6.6x3.5x1.0

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

25
Connector Series Specifications Remarks
50V / 0.2A
11 to 51 circuits pitch 0.3 mm
FXV ZIF front flip-lock type
dimensions (e.g. 17 circuits)
SMT SIDE entry 7.1x2.8x0.9

50V / 0.2A pitch 0.3 mm

25 and 29 circuits low profile: 1.0 mm
FXW ZIF slider locking type
SMT dimensions (e.g. 25 circuits)
SIDE entry 10.4x4.8x1.0

50V / 0.2A pitch 0.3 mm

15 to 81 circuits housing material LCP
FXY ZIF front flip-lock type
dimensions (e.g. 15 circuits)
SMT SIDE entry 7.7x4.45x1.3

50V / 0.2A
15 to 73 circuits pitch 0.3 mm
FXZ ZIF front flip-lock type
dimensions (e.g. 15 circuits)
SMT SIDE entry 6.6x3.95x1.4

50V / 0.2A
17 to 51 circuits pitch 0.3 mm
dimensions (e.g. 17 circuits)
FXZT ZIF TOP entry 8.0x2.85x3.6
SMT

50V / 0.5A
5 to 24 circuits pitch 0.4 mm
FZ non-ZIF dimensions (e.g. 5 circuits)
SMT SIDE entry 3.45x2.65x1.0

50V / 0.5A pitch 0.5 mm

5 to 25 circuits tinned and gold plated
FH non-ZIF version available
SMT dimensions (e.g. 5 circuits)
SIDE entry 5.9x3.55x1.2

50V / 0.5A pitch 0.5 mm

10 to 60 circuits back flip-lock type
FHH ZIF dimensions (e.g. 10 circuits)
SMT SIDE entry 8.6x6.7x2.0

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

26
Connector Series Specifications Remarks
pitch 0.5 mm
50V / 0.5A tinned and gold plated
4 to 24 circuits version available
FHJ housing material LCP
non-ZIF
dimensions (e.g. 4 circuits)
SMT SIDE entry 4.1x3.55x1.2

50V / 0.5A
3 to 9 circuits pitch 0.5 mm
FHS ZIF front flip-lock type
dimensions (e.g. 4 circuits)
SMT SIDE entry 4.06x2.95x0.9

50V / 0.5A pitch 0.5 mm

4 to 28 circuits low profile: 0.9 mm
FHSY
ZIF front flip-lock type
SMT dimensions (e.g. 4 circuits)
SIDE entry 4.06x3.25x0.9

50V / 0.5A
10 to 60 circuits pitch 0.5 mm
FHY ZIF front flip-lock type
dimensions (e.g. 10 circuits)
SMT SIDE entry 8.7x4.0x1.3

50V / 0.5A
5 to 32 circuits pitch 0.5 mm
FKZ ZIF slider locking type
dimensions (e.g. 4 circuits)
SMT SIDE entry 7.5x4.4x1.8

50V / 0.5A pitch 0.5 mm

4 to 40 circuits housing material LCP
FLH slider locking type
ZIF
dimensions (e.g. 4 circuits)
SMT SIDE entry 7.7x4.5x1.2

50V / 0.5A pitch 0.5 mm

6 to 40 circuits low insertion force type
FLT non-ZIF dimensions (e.g. 6 circuits)
SMT TOP entry 4.9x2.95x4.15

pitch 0.5 mm
50V / 0.5A normal and reverse
FLZ 6-50 circuits version available
ZIF slider locking type
SMT dimensions (e.g. 6 circuits)
SIDE entry 8.9x4.6x2.0

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

27
Connector Series Specifications Remarks

pitch 0.5 mm
50V / 0.5A normal and reverse
6 to 42 circuits version available
FLZT
ZIF slider locking type
SMT dimensions (e.g. 6 circuits)
TOP entry 8.5x3.0x3.9

50V / 0.5A pitch 0.5 mm

18 to 50 circuits front flip-lock type
FLZX reversed type
ZIF
dimensions (e.g. 20 circuits)
SMT SIDE entry 10.55x5.6x2.0

30V / 0.3A
pitch 0.5 mm
30, 40 and 50 circuits
top and side entry available
FY Non-ZIF dimensions (e.g. 30 circuits)
SMT TOP entry 17.7x4.04x5.2
SIDE entry 17.7x5.2 x3.0

50V / 1.0A pitch 1.0 mm

8 to 26 circuits top and side entry available
FAZ ZIF slider locking type
SMT dimensions (e.g. 9 circuits)
TOP entry 14.4x3.75x5.0
SIDE entry 14.4x5.0 x2.8

pitch 1.0 mm
50V / 0.5A
top and side entry available
3 to 12 circuits
double-sided contacts
FM non-ZIF dimensions (e.g. 4 circuits)
SMT and THT available TOP entry 6.0x3.0x4.4
SIDE entry 6.0x4.4x3.0

pitch 1.0 mm
50V / 0.5A top and side entry available
4-40 circuits reversed and normal type
FMN non-ZIF available
SMT and THT available dimensions (e.g. 4 circuits)
TOP entry 6.0x3.0x5.1
low insertion force SIDE entry 7.0x5.1x3.0

50V / 0.5A pitch 1.0 mm

3 to 14 circuits double-sided contacts
dimensions (e.g. 4 circuits)
FMS non-ZIF SIDE entry 6.0x5.3x2.8
SMT

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

28
Connector Series Specifications Remarks
pitch 1.0 mm
50V / 0.5A
top and side entry available
6 to 30 circuits
FMZ slider locking type
ZIF dimensions (e.g. 6 circuits)
THT TOP entry 12.0x3.95x8.0
SIDE entry 12.0x8.0 x4.2

50V / 0.5A pitch 1.0 mm

7 to 25 circuits slider locking type
FPZ
ZIF dimensions (e.g. 7 circuits)
SMT SIDE entry 13.0x6.5x2.9

pitch 1.25 mm
200V / 1.0A
top and side entry available
4 to 40 circuits dimensions (e.g. 4 circuits)
FE
non-ZIF TOP entry 8.55x4.8x7.5
SIDE entry 8.55x7.5x4.8
THT

50V / 0.5A
4 to 26 circuits pitch 1.25 mm
FFS dimensions (e.g. 4 circuits)
non-ZIF SIDE entry 7.55x5.3x2.8
SMT

pitch 2.54 mm
250V / 1.0A
top and side entry available
5 to 19 circuits
FDZ double-sided contacts
ZIF dimensions (e.g. 5 circuits)
THT TOP entry 23.56x7.7 x12.7
SIDE entry 23.56x10.2x7.7

Coaxial Connector

Connector Series Specifications Remarks

wire to board for W-LAN, WiMAX,

AYU 1 12 GHz / 50 Bluetooth, GPS
SMT

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

29
 Interface Connectors
Connector Series Remarks

SCZT
Nano SIM (4FF)
SCZW

SCYT
Micro SIM
SCYU

SCG
SCK SIM
SCR

SDHK
SDHL
Micro SD
SDHR
SDHT

SD
SDK SD / MMC cards
SDKR

0.5 A
10.000 mating cycles
ICM-MA
type I and II
connector, adapter, card frame, ejector

24 circuits
CFF mating/unmating
cycles: 10.000

USB
Type A, B (2.0)
3.0 and Type C (3.1)
UB USB Type C waterproof (development)
Mini B-type
Micro USB
Micro USB waterproof

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

30
 Loose Piece Terminals and Chain Terminals
Terminal Series Specifications Remarks

ring tongues: top and side

for wires 0.2-325 mm2
entry; spade and fork
with and without insulation
LPT tongues; pin tongues;
loose or taped
blade and flag tongues;
closed-end and splices

tab-on and tab-in

for wires 0.2-5.5 mm2 terminals, also with
Chain without insulation Positive Lock; top entry
Terminals taped or loose and side entry; ring and
fork tongues, splices;
insulation sleeves

Tooling Service

JST tooling for high quality harnesses:

You are looking for a handtool to crimp a JST crimp terminal?
Or you need to manufacture an IDC harness?
We are able to offer you hand tools for both.

Or do you need to manufacture high quantities?

JST offers you tooling for crimp and IDC production.

We look forward to your inquiry.

Harness Production

JST Deutschland offers you cost-effective

production of your harnesses.
Of course we can also offer small lot sizes
made by hand as well as high quantities
made fully-automatically.

Test us and contact us for a free quote.

In any case JST is a reliable partner for you.

UL registered harness maker

Category ZPFW2 (US) and ZPFW8 (Canada)
File No. E466125

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

31
 Your benefits:

• more than 50 years experience in

connector manufacturing
• local warehousing
• distribution sales network
• WebEDI and consignment stock
• separate samples logistic – samples
within 1 working day
• competitive pricing due to production in
low labour countries
• German Project- / Product-Management
• dedicated inside and outside sales team
• highly skilled personnel in harness
assembly
• tooling service
• technical support

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

32
 I N D E X
Connector series name in alphabetical order

These specifications comply with the latest status quo and are subject to change without any notice.
* = depends on wire range dimensions width x depth x height
(without contact pins on PCB)

33
 JST Deutschland GmbH
Küferstr. 15
D-73650 Winterbach
Switchboard:
These specifications comply +49
with the latest status /and
quo 71are
81 / 40
subject 07 - 0without any notice.
to change
* = depends onTelefax:
wire range +49 / 71 81 / 40(without
07
dimensions –
width x21
depth x height
contact pins on PCB)
www.JST.de
[email protected]
34