DOOSAN INFRACORE GENERATOR ENGINE

P222LE-II
Ratings Gross Engine Output Net Engine Output
( kWm/PS) Standby Prime Standby Prime
1500rpm(50Hz) 652/886 - 629/855 -
1800rpm(60Hz) 736/1000 - 698/948 -

Ratings Definitions
The power ratings of Emergency Standby and Prime are in accordance with ISO 8528.
Fuel Stop power in accordance with ISO 3046.
STANDBY POWER RATING is applicable for supplying emergency power for the duration of the utility power outage.
No overload capability is available for this rating. A standby rated engine should be sized for a maximum of an 70% average
load factor and 200 hours of operation per year. This includes less than 25 hours per year at the Standby Power rating.
PRIME POWER RATING is available for an unlimited number of hours per year in variable load application. Variable load
should not exceed a 70% average of the Prime Power rating during any operating period of 250 hours. The Total operating
time at 100% Prime Power shall not exceed 500 hours per year. A 10% overload capability is available for a period of 1 hour
withing a 12 hour period of operation. Total operating time at the 10% overload power shall not exceed 25 hous per year

◎ GENERAL ENGINE DATA

ㅇEngine Model P222LE-S
ㅇEngine Type 4-Cycle, V-type, 12-Cylinder, Turbo charged & intercooled (air to air)
ㅇBore x stroke 128 x 142 mm
ㅇDisplacement 21.927 liters
ㅇCompression ratio 14.6 : 1 (60Hz) / 14.0 : 1 (50Hz)
ㅇRotation Counter clockwise viewed from Flywheel
ㅇFiring order 1-12-5-8-3-10-6-7-2-11-4-9
ㅇInjection timming 19˚ BTDC (60Hz) / 13˚ BTDC (50Hz)
ㅇDry weight 1,591 kg(with Fan)
ㅇDimension (LxWxH) 1,697 x 1,389 x 1,281 mm
ㅇFly wheel housing SAE NO.1M
ㅇFly wheel Clutch NO.14M
ㅇNumber of teeth on flywheel 160
◎ ENGINE MOUNTING
Maximum Bending Moment at Rear Face to Block 1,325 N.m
◎ EXHAUST SYSTEM
Maximum Back Pressure 5.9 kPa
◎ AIR INDUCTION SYSTEM
Maximum Intake Air Restriction
. With Clean Filter Element 2.16 kPa
. With Dirty Filter Element 6.23 kPa
ㅇMax. static pressure after Radiator 0.125 kPa

Printed in 2012 PD&E_P222LE-II_V.01

◎ COOLING SYSTEM
Water circulation by centrifugal pump on engine.
ㅇCooling method Fresh water forced circulation
ㅇCoolant capacity Engine Only : Approx. 23 lit, With Radiator(standard) : Approx 88 lit.

ㅇPressure Cap Max. 49 kPa

ㅇWater Temperature
- Maximum for standby and Prime 103℃
- Before start of full load 40.0℃
ㅇWater pump Centrifugal type driven by belt
ㅇThermostat Type and Range Wax – pellet type, Opening temp. 71°C , Full open temp. 85°C
ㅇCooling fan Blower type, plastic , 915 mm diameter, 9 blade
ㅇMax. external coolant system restriction Not available
◎ LUBRICATION SYSTEM
Force-feed lubrication by gear pump, lubricating oil cooling in cooling water circuit of engine.
ㅇLub. Method Fully forced pressure feed type
ㅇOil pump Gear type driven by crank-shaft gear
ㅇOil filter Full flow, cartridge type
ㅇOil capacity Max. 40 liters , Min. 33 liters
ㅇLub oil pressure Idle Speed : Min 100 kPa
Governed Speed : Min 250 kPa
ㅇMaximum oil temperature 120℃
ㅇAngularity limit Front down 10 deg , Front up 10 deg , Side to side 22.5 deg
ㅇLubrication oil p
Refer to Operation Manual
◎ FUEL SYSTEM
Bosch type in-line pump with integrated, electromagnetic actuator.
ㅇInjection pump Bosch in-line "P" type
ㅇGovernor Electric type
ㅇSpeed drop G3 Class ( ISO 8528 )
ㅇFeed pump Mechanical type in injpump.
ㅇInjection nozzle Multi hole type
ㅇOpening pressure 27.9 MPa
ㅇFuel filter Full flow, cartridge type with water drain valve.
ㅇMaximum fuel inlet restriction 10 kPa
ㅇMaximum fuel return restriction 60 kPa
ㅇFuel feed pump Capacity 630 liters / hr
ㅇUsed fuel Diesel fuel oil
◎ ELECTRICAL SYSTEM
ㅇBattery Charging Alternator 60Hz : without alternator, 50Hz : 28.5V x 45A alternator
ㅇVoltage regulator 60Hz : without alternator, 50Hz : Built-in type IC regulator
ㅇStarting motor 24V x 7.0 kW
ㅇBattery Voltage 24V
ㅇBattery Capacity 2 x 100 Ah (recommended)
ㅇStarting aid (Option) Block heater, Air Heater

Printed in 2012 PD&E_P222LE-II_V.01

◎ VALVE SYSTEM
ㅇ Type Overhead valve type
ㅇ Number of valve Intake 1, exhaust 1 per cylinder
ㅇ Valve lashes at cold Intake 0.3 mm , Exhaust 0.4 mm
ㅇ Valve timing
Opening Close
-. Intake valve 24 deg. BTDC 36 deg. ABDC
-. Exhaust valve 63 deg. BBDC 27 deg. ATDC

◎ PERFORMANCE DATA Prime Power Standby Power

ㅇGoverned Engine speed rpm 1500 1800 1500 1800
ㅇEngine Idle Speed rpm 800 800 800 800
ㅇOver speed limit rpm - - 1650 1980
ㅇGross Engine Power Output kW - - 652 736
ps - - 886 1000
ㅇBreak Mean effective pressureMPa - - 2.38 2.24
ㅇMean Piston Speed m/s - - 7.1 8.5
ㅇFriction Horsepower kW - - 32 44
ps - - 43.5 59.8
ㅇ Specific fuel consumption
25% load liters/hr - - 41.7 48.2
50% load liters/hr - - 79.5 88.5
75% load liters/hr - - 119.3 133.0
100%
% load liters/hr - - 162.6 180.3
ㅇMaximum Lube oil consumptiog/h - - 620 700
ㅇFan Power kW 23 38 23 38
ㅇExhaust Noise at 1m Horizontally from Centerline of Exhaust Pipe distance
(without Fan) dB(A) 101.8 102.6 101.8 102.6
The all data and the specific fuel consumption are based on ISO 3046/1, Standard reference conditions are in accordance
with 298 K(25˚ Celsius) air temperature, 100kPa(1000mbar) air pressure, 60% relative humidity, 110m(361ft) altitude.
Operation At Elevated Temperature And Altitude: The engine may be operated at :
1800 rpm & 1500rpm up to 750~ 1000m and 30°C without power deration
For sustained operation above these conditions, derate by 3% per 304m , and 2% per 11 °C
Engine Data with Dry Type Exhaust Manifold
ㅇ Intake Air Flow m3/min - - 42.5 52.9
ㅇExhaust gas temp. after turbo °C - - 635 548
ㅇExhaust Gas Flow m3/min - - 119.9 129.4
ㅇHeat Rejection to Exhaust kW - - 573.0 635.4
ㅇHeat Rejection to Coolant kW - - 249.1 276.2
ㅇHeat Rejetion to Intercooler kW - - 132.9 147.3
ㅇRadiated Heat to Ambient kW - - 58.1 64.5
ㅇCooling water circulation liters/min - - 645 720
ㅇCooling fan air flow m3/min - - 606 702

Printed in 2012 PD&E_P222LE-II_V.01

◆ ENGINE DIMENSION

◆ CONVERSION TABLE
in. = mm x 0.0394 lb/ft = N.m x 0.737
PS = kW x 1.3596 U.S. gal = lit. x 0.264
psi = kg/cm2 x 14.2233 kW = 0.2388 kcal/s
in3 = lit. x 61.02 lb/PS.h = g/kW.h x 0.00162
hp = PS x 0.98635 cfm = m3/min x 35.336
lb = kg x 2.20462 MPa = kPa x 1000 = bar x 10
kW = kcal/sec x 0.239

Doosan Infracore Co. Ltd.,

21st Floor
Floor, Doosan Tower
Tower, 18-12
18-12, Euljiro 6-ga,
6-ga Jung-gu
Jung-gu,
Seoul, Korea.

TEL : 82-2-3398-8578 FAX : 82-2-3398-8509

E-mail : [email protected]
Web site : www.doosaninfracore.com

※ Speccifications are subject to change without prior notice

Printed in 2012 PD&E_P222LE-II_V.01