Scribd
Upload
123 views

AVR USB Programmer

The AVR USB JTAG is a development tool that can program, emulate, and debug AVR microcontrollers with a JTAG interface. It has a 10-pin JTAG connector and USB connector, and can be used to program all AVR microcontrollers without an external power supply. It provides standard 2x10 pin JTAG interface and can debug and program AVR microcontrollers. LED indicators show the power and configuration status, and a switch can optionally power a connected target board from the USB connection.

Uploaded by

Mohit Sharma
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
123 views

AVR USB Programmer

The AVR USB JTAG is a development tool that can program, emulate, and debug AVR microcontrollers with a JTAG interface. It has a 10-pin JTAG connector and USB connector, and can be used to program all AVR microcontrollers without an external power supply. It provides standard 2x10 pin JTAG interface and can debug and program AVR microcontrollers. LED indicators show the power and configuration status, and a switch can optionally power a connected target board from the USB connection.

Uploaded by

Mohit Sharma
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Robotic Boards

AVR USB JTAG


Programmer

AVR USB JTAG is the best development tool


for programming, real time emulation and debugging JTAG Inter face

for AVR microcontrollers with JTAG interface. What’s R2

www.robosoftsystems.co.in
74ACT125

R8
Non ISP
more, it doesn’t require an external power supply, and

Switch
D
come with a facility to power embedded AVR controller

R10
47 mm
boards which require upto 5V drive.
C1 D2
R4
Specification:
Crystal

AT89C2051
C3

R9
 Dimensions: 47mm x 30.5 mm D2
C4

 It has one 10-pin JTAG connector and USB mini B R3

type connector D1
R6

R2

R1

 Can be used to program all AVR microcontrollers


R5
+D

USB
C2

-D

 Comes with 10-pin flat ribbon cable to connect to


the target board
 USB 2.0 Full Speed device (12 Mbits/sec) interface
 Can be used to debug and program all AVR
30.5 mm
 Provides a standard 2X10 pin JTAG interface
 No external power supply required

dfddfdfddfdf
Page 1 www.robosoftsystems.co.in
Overview of the device

Points to notice:
LED’s functions :-
 Power Led (D3) is used to indicate power to the programmer board.

 Initially the power LED glows continuously along with the blinking –D and +D Led’s. Later the
–D LED settles down to glow & +D turns off. At the same time configuration LED (D2) starts
glowing continuously.
 Configure Led (D2) is used to indicate successful configuration of the USB programmer board.

Switch functions :-
 Switch can be used to power the target AVR board. When placed on Power Target, the program-
mer will power the target AVR board, otherwise not.
 It should be noted that, there is no regulated power supply on the programmer board, thus it pro-
vides direct power from the USB. One should not use this supply if there are any electronic com-
ponents on the target board that have a operation voltage less than the USB supply voltage(4.5 V),
otherwise the components may get damaged.

How to use ?
After successfully connecting the USB, one will find Power Led (D3), –D LED and configura-
tion LED (D2) continue to glow. Otherwise the connection is not proper, and it is advised to recon-
firm the connection cables and connection setup. Shown below is the image of the response after the
programmer connection is successfully established.

dfddfdfddfdf
Page 2 www.robosoftsystems.co.in
How to use ? (contd...)

Target Power can be used to power the target AVR Board. With the help of a Flat Ribbon Ca-
ble one can connect the programmer to the target AVR board. The setup is now ready for program-
ming the AVR.

Shown below is the image of the response after the programmer is successfully connected with the
main AVR board.

(*Note: the response should be similar when the following command line is issued —>
― avrdude –c usbtiny –p m16 ―

dfddfdfddfdf
Page 3 www.robosoftsystems.co.in

You might also like