1,The property which enables to be drawn into wires is called?

(a) Ductility (b) Mallability (c) Toughness (d) Brittleness 1

2,The property when the material fails to yield and change its shape it subjected
to a stress but breaks suddenly is called?
(a) Ductility (b) Mallability (c) Toughness (d) Brittleness 4
3,The stored energy in the material is called?
(a) Mallability (b) Resilence (c) Toughness (d) Brittleness 2
4,The resistance which a body offers to being pulled asunder by tensile force is called?
(a) Ductility (b) Mallability (c) Toughness (d) Tenacity 4
5,The range of the poison's ratio is?
(a) 0 to 0.15 (b) 0.15 to 0.25 (c) 0.25 to 0.34 (d) 0.34 to 0.5 3
6,The maximum stress of metal can withstand without breaking or without
failure for a specific number of stress reveals is?
(a) Ductility (b) Tensile strength (c) Fatigue strength (d) Shear strength 3
7,The largest load repeatedly applied which a piece will carry without taking
permanant set is called ?
(a) Pay load (b) Proof load (c) Ultimate load (d) None 2
8,The alloy of copper and Zinc is ?
(a) Brass (b) Cast iron (c) Bronze (d) Steel 1
9,The strength of the alloys of iron is depends on?
(a) Sulphur content (b) Carbon content (c) Manganese content (d) None 2
10,The carbon content in the cast iron is?
(a) 3 to 4 % (b) 0.15 % (c) 1.8 to 5 % (d) 5 to 6 % 3
11,The carbon content in the steel is?
(a) 3 to 4 % (b) 0.15 % (c) 1.8 to 5 % (d) less than 1.8 % 4
12,In steel as well as in wrought iron the percentage of sulphur should not exceed ?
(a) 0.06 (b) 0.1 (c) 0.5 (d) 0.8 1
13,In wrought iron the % of phosphourus should not exceed ?
(a) 0.06 (b) 0.2 (c) 0.5 (d) 1.0 2
14,The process of heating the metal to normalising temparature and then allowing
it to cool slowly and uniformly not in air is called?
(a) Forging (b) Normalising (c) Annealing (d) Hardening 3
15,The objective of annealing is?
(a) To remove internal strains (b) To reduce the size of crystal grains
© To improve the strength (d) None 1
16,Periodical heat treatment is not necessary if the chains are made of mild steel
with a manganese percentage of?
(a) 0.06 (b) 0.5 (c) 1.0 (d) 1.5 4
17,The process of heating steel to a temparature slightly above critical temparature
and allowing it to cool naturally in air is called?
(a) Forging (b) Normalising (c) Annealing (d) Hardening 2
18,The object of normalising is?
(a) To remove internal strains (b) To reduce the size of crystal grains
© To improve the strength (d) None 2
19,The process of heating steel gradually uniformely to a temparature higher than the
critical temparature and then cooled rapidly by quenching water is called?
(a) Forging (b) Normalising (c) Annealing (d) Hardening 4
20,The elements in the GUNMETAL are?
(a) Copper and zinc (b) Copper ; tin and zinc
(c) Copper and tunston and nickel (d) None 2
21,The elements in the WHITE METAL are?
(a) Tin ; Antimony ;Lead;Copper (b) Copper ; tin ; chromium
© Copper ; zinc;Tin (d) Tungston and chromium 1
22,The percentage of silver content in the GERMAN SILVER is?
(a) 10 % (b) 5 % (c) 2.5 % (d) 0 % 4
23,Rods are dipped in diluted H2SO4 or HCL to remove scales is called?
(a) Patenting (b) Forging (c) Pickling (d) Normalising 3
24,The steel rod for wire making becomes homogeneous by the process of?
(a) Patenting or normalizing (b) Forging (c) Pickling (d) Annealing 1
25,In stainless steel the chromium percentage is?
(a) 10 to 15 % (b) 18 to 20 % (c) 25 to 30 % (d) less than 10% 2
26,The steel is unweldable if it contains carbon content?
(a) Less than 0.5 % (b) 0.5 to 1 % (c) 1 to 1.2 % (d) More than 1.25 % 4
27,The ultimate strength of the wires for haulage or winding is....kgf/sq.mm?
(a) 160 (b) 100 (c) 200 (d) 400 1
28,The ropes required to carry the burden or load but more or less stationary is called?
(a) Non-stranded (b) Stranded (c) Standing (d) Running 3
29,The ropes which undergoes frequent movement or coinling often with varying
loads are called?
(a) Non-stranded (b) Stranded (c) Standing (d) Running 4
30,Guy ropes;guide ropes are the example of?
(a) Non-stranded ropes (b) Stranded ropes
(c) Standing ropes (d) Running ropes 3
31,The ropes used for winding;haulage;coal cutting machine are the example of?
(a) Non-stranded (b) Stranded (c) Standing (d) Running 4
32,The wires spiral round the core in the same direction as the threads of left hand
screw are called?
(a) Non-stranded (b) Stranded (c) Right hand ropes (d) Lefthand ropes 4
33,A number of concentrically twisted wire laid in the form of a helix round a central
steel wire is known as?
(a) Lang's lay (b) Ordinary lay (c) Strand (d) Locked coil 3
34,If the wires in the strand and the strands in the rope are laid in the opposite direction is called?
(a) Lang's lay (b) Ordinary lay (c) Right hand (d) Locked coil 2
35,If the wires in the strand and the strands in the rope are laid in the same direction is called?
(a) Lang's lay (b) Ordinary lay (c) Right hand (d) Locked coil 1
36,The wire ropes which offers better wearing surface and more resist to bending fatigue are called?
(a) Lang's lay (b) Ordinary lay (c) Right hand (d) Locked coil 1
37,Internal stresses of the rope can be relieve with the use of?
(a) Normalising the wire (b) Annealing the wire
(c) Performed wire (d) Wassington pattern 3
38,Example of non stranded rope is?
(a) Performed rope (b) Equal lay ropes (c) Regular lay (d) Locked coil ropes 4
39,The wire ropes required to be used in wet shafts are?
(a) NOnrusting type (b) Galvanised (c) Bronze (d) Stainless steel 2
40,For winding purpose the locked coil ropes are preffered because?
(a) offers greator resistance (b) had greater fill factor
© permits high factor of safety (d) can't spliced 3
41,The type of rope most suitable for balancing rope in koepe winding is?
(a) Regular lay (b) Locked coil (c) Flattened strand (d) Spiral strand 3
42,The ropes used for guide ropes are?
(a) Locked coil (b) Regular lay (c) Lang's lay (d) Flattened strand 1
43,The ropes used for CCM are?
(a) Locked coil (b) Regular lay (c) Lang's lay (d) Flattened strand 2
44,The ropes used for dragline are?
(a) Locked coil (b) Regular lay (c) Lang's lay (d) Flattened strand 3
45,The ropes used for winding are?
(a) Locked coil (b) Regular lay (c) Lang's lay (d) Flattened strand 3
46,The space factor for stranded rope is?
(a) 30 to 40 % (b) 40 to 50 % (c) 50 to 60 % (d) 75 % 3
47,The space factor for locked coil rope is?
(a) 30 to 40 % (b) 40 to 50 % (c) 50 to 60 % (d) 75 % 4
48,IN socketing the rope length under clips is nearly.....times the dia?
(a) 10 (b) 20 (c) 30 (d) 40 3
49,Most commonly used capel for rope haulage is?
(a) Split capel (b) Coned socket (c) Interlocking wedge type
(d) Bent back wire cone socket 2
50,In coned socket type cappel the metal poured is?
(a) Gunmetal (b) Brass (c) Whitemetal (d) Babbit metal 3
51,In preparation of cone socket type cappel the white metal should not be heated more than?
(a) 100 deg c (b) 200 deg c (c) 365 deg c (D) 450 deg c 3
52,In reliance capel the tapping of wedge is?
(a) 1 in 5 (b) 1 in 10 (c) 1 in 15 (d) 1 in 20 4
53,The jaws of the reliance capel are about ...times rope diameter in length?
(a) 30 (b) 24 (c) 12 (d) 15 2
54,The method of joining two wire ropes permanantly without using special fittings
or attachments is called?
(a) Splicing (b) Socketing (c) Performing (d) None 1
55,The length of splice for 13 mm dia rope is?
(a) 2 to 3m (b) 4 to 5 m (c) 6 to 9 m (d) 10 to 15 m 3
56,The length of splice for 25 mm dia rope is?
(a) 2 to 3m (b) 4 to 5 m (c) 6 to 9 m (d) 10 to 15 m 4
57,Example of equal lay ropes is?
(a) Flattend strand (b) Performed (c) Warrington pattern (d) None 3
58,The capacity of the rope to resist the kinetic shock is roughly ?
(a) Proportional to Dia of rope (b) Inversely Proportional to Dia of rope
© Proportional to length (d) Inversely proportional to length 3
59,No rope should be allowed to remain in use after the wires have lost their diameter by?
(a) 10 % (b) 20 % (c) 30 % (d) 40 % 2
60,The ratio between breaking load and total suspended rope is called?
(a) Fill factor (b) Factor of safety (c) Capacity factor (d) Bending factor 3
61,The ratio between drum dia to the rope dia is called?
(a) Fill factor (b) Factor of safety (c) Capacity factor (d) Beding factor 4
62,If the dia of a wire is 'D' then the dia of the simple round stranded rope is?
(a) 6D (b) 8D (c) 10D (d) 12D 1
63,The height of the head gear is depend on the?
(a) Skip and cage (b) Position of the drum (c) Fleet angle (d) Depth of the shaft 1
64,The distance between headgear pulley and detaching plate is?
(a) 2 M (b) 3 M (c) 4 M (d) 6 M 2
65,A wind pressure on the exposed surface of the head gear frame may be taken as.....N/sq.m ?
(a) 100 (b) 750 (c) 1340 (d) 3000 3
66,The diameter of headgear pulley should be atleast.....times the dia of the rope?
(a) 60 (b) 100 (c) 120 (d) 150 2
67,Pulleys normally above ....m dia are made in to two halves?
(a) 2.5 (b) 3.5 (c) 4 (d) 6 1
68,The diameter of the headgear pulley should be ....of the rope diameter for
stranded ropes and.....for locked coil ropes?
(a) 80 % ; 100 % (b) 100 % ; 110 % (c) 110 % ; 105 % (d) 105 % ; 110 % 3
69,The angle of fleet should not exceed?
(a) 1 deg (b) 1.5 deg (c) 3 deg (d) 5 deg 2
70,The pay load carried by skip is?
(a) 6 te (b) 8 te (c) 10 te (d) 12 te 2
71,The ratio of pay load to gross load for skip winding is...and for cage winding is...?
(a) 0.6 ; 0.35 (b) 0.35 ; 0.6 (c) 0.8 ; 0.6 (d) 0.6 ; 0.8 1
72,The groove of the head gear pulley should be ....of the circumference of the rope
is in contact with the groove?
(a) ¼ (b) ½ (c) 1/3 (d) ¾ 3
73,The number of spokes in head gear pulley are?
(a) 15 (b) 19 (c) 21 (d) 25 3
74,The cage chains should be anneleaned atleast once in?
(a) 3 months (b) 6 months (c) 9 months (d) 12 months 2
75,The components of cage arrachements chanins; links; shackeles; are exempted
from periodical heat treatment if they are made of?
(a) wrought iron (b) Mild steel
(c) 0.5 % carbon steel (d) 1.5 % Manganese steel 4
76,The most important role plays in a safety that a component detaching hook is?
(a) Jaws (b) Centre pivot (c) Copper pin (d) D link pin 3
77,All the suspension gear should be renewed after every ..?
(a ) 5 years (b) 7 years (c) 10 years (d) 15 years 3
78,The levels in safety catches spaced at intervals varying from?
(a) 0.1 to 0.3 m (b) .3 to 1m (c) 1 to 1.3 m (d) 1.3 to 2 m 2
79,Retractable supports for cages used while loading and unloading being carried
at the top of the shaft are?
(a) Safety catches (b) bell plates (c) keps (d) platform 3
80,In case of koepe winding the decking difficulties while loading and unloading
the cage are overcome by the use of?
(a) Safety catches (b) bell plates (c) Keps (d) Hinged platform 4
81,The weight of the steel guides is...kgf/m?
(a) 5 to 10 (b) 10 to 20 (c) 20 to 55 (d) 60 to 90 3
82,The minimum space between two cages is generally?
(a) 20 cm (b) 30 cm (c) 40 cm (d ) 50 cm 3
83,The tensioning arrangement weights are about ....KN per 100 m depth of shallow
mines and ...KN per 100 m depth for deep mines?
(a) 10 ; 5 (b) 5 ;10 (c) 10 ; 20 (d) 20 ; 10 1
84,The life of the guide ropes is?
(a) 10 years (b) 20 years (c) 5 years (d) 3.5 years 1
85,The factor of safety for the drum winding is?
(a) 6 (b) 7 (c) 9 (d) 10 4
86,The factor of safety for the friction winding is?
(a) 6.5 to 8 (b) 9 (c) 10 (d) 12 1
87,While recapping atleast ...m long rope should be cut near the rope cappel?
(a) 1 m (b) 2 m (c) 3 m (d) 4.5 m 2
88,The maximum life of the winding rope is?
(a) 10 years (b) 7 years (c) 5 years (d) 3.5 years 4
89,The torques on the winding drum due to loaded cage and due to empty may be
balanced as far as practicable by?
(a) Use of balancing rope (b) Use of suitable shape of pulley
© Changing the load on the two cages (d) COntrolling the speed 1
90,The method of nearly balancing the torques on the winding engine in deep
shaft winding by the use of?
(a) Balancing rope (b) Bi cyclo conical drum
(c) Conical drum (d) Large cylindrical drum 2
91,The two factors i.e torque required to raise the load and the winding speed govern?
(a) Power required for winding engine (b) Size of the motor for winding
© Type of winder (d) Power rating of winding engine 4
92,The arc of contacting of winding rope in tower mounted friction winding is....deg ?
(a) 90 to 120 (b) 120 to 150 (c) 200 to 230 (d) 250 to 280 3
93,The arc of contacting of winding rope in friction winding is....deg ?
(a) 90 to 120 (b) 120 to 150 (c) 185 to 230 (d) 250 to 280 3
94,The coefficient of friction between the sheave lining and the rope is minimum of?
(a) 0.12 (b) 0.2 (c) 0.4 (d) 0.65 2
95,The rope may slip over the wheel when the ratio T1:T2 exceeds a value?
(a) 1.2 to 1.3 (b) 1.4 to 1.5 (c) 1.5 to 1.6 (d) 1.8 to 2 3
96,In very deep mining the method of winding best suited is?
(a) Drum winding (b) Koepe winding (c) Tower mounted koepe winding
(d) Blair winding, 4
97,The method of speed control and electric winder of large capacity i.e above 800kw is?
(a) sheostatic control (b) Liquid control (c) Ward leonard speed control
(d) Electrical breaking 3
98,Automaric contrivances should be provided for every shaft exceeding minimum....m depth?
(a) 50 (b) 80 (c) 100 (d) 150 3
99,When men are being hoisted orlowered as the cage appoached pit top or
pit bottom decking level its speed should not exceed 1.5 m/sec such arrangement is known as?
(a) Over speed device (b) Overwind device (c) Wardleonard control
(d) Slow banking device 4
100,Mechanical breaks are applied upto depth of?
(a) 100 m (b) 200 m (c) 300 m (d) 400 m 2
101,Regenarative braking is used when?
(a) Hoising loads (b) lowering loads (c) Inspection of the cage (d) None 2
102,In koepe winding the overwind is prevented by?
(a) Detaching hook (b) Automatic contrivances
(c) Convergence of the guides (d) None 3
103,In the event of power failure the brake automatically applied is?
(a) Mechanical brake (b) Thrustor brake (c) Regenarative brake (d) None 2
104,The portion of the rope suffers from most severe shocks is?
(a) Near the capel (b) Near the drum (c) The part of the rope that rests on the drum
(d) Part of the rope rests on headgear pulley 1
105,The raising capacity of amine depends on the shaft capacity which in turn depends on?
(a) Speed of winding (b) Pit top and pit bottom arrangement
(c) Rolling stock (d) Despatch system 2
106,The pit top and pit bottom arrangement which deals with reasonable output
per month and occupies less space is?
(a) Run round arrangement (b) Back shunt circuit (c) Turn table circuit
(d) Traverse circuit 3
107,The out put per month for the turn table circuit is?
(a) 50000 (b) 40000 (c) 30000 (d) 20000 3
108,The out put per month for the Backshunt circuit is?
(a) 50000 (b) 40000 (c) 30000 (d) 20000 1
109,The simplest system of haulage system for raising the loads?
(a) Direct rope haulage (b) Endless rope haulage
(c) Main tail rope haulage (d) Gravity 1
110,The gradient suitable for direct rope haulage is steeper than?
(a) 1 in 15 (b) 1 in 3 (c) 1 in 10 (d) 1 in 30 3
111,The general speed in rope haulage is?
(a) 2 to 3 Km/h (b) 3 to 7 km/h (c) 8 to 12 km/h (d) 15 km/h 3
112,The limiting gradient for endless rope haulage is?
(a) 1 in 6 (b) 1 in 4 (c) 1 in 10 (d) 1 in 15 1
113,The rope speed in the endless rope haulage is?
(a) 2 to 3 Km/h (b) 3 to 7 km/h (c) 8 to 12 km/h (d) 15 km/h 2
114,Where continuous movement of loaded and empty tubs are necessary the
rope haulage suitable is?
(a) Direct rope haulage (b) Endless rope haulage
(c) Main tail rope haulage (d) Gravity 2
115,The surface of the drive pulley in endless haulage is?
(a) Flat (b) Curved (c) Tapered (d) Grooved 3
116,In endless rope haulage the C.I sheets having the tapering of?
(a) 1 in 6 (b) 1 in 4 (c) 1 in 10 (d) 1 in 8 4
117,The correct place for tension bogey is?
(a) near the haulage engine (b) any point on the level roadway
© at the point where slack rope is most likely to occur (d) none 3
118,Smalman clip is the device used to attach?
(a) Direct rope haulage (b) Endless rope haulage
(c) Main tail rope haulage (d) Gravity 2
119,In over rope endless haulage system ...... is used for attaching the tubs?
(a) Screw clip (b) Smallman clip (c) Cam clip (d) Lashing chain 4
120,The system of rope haulage most suitable for undulating roadways and where
it is not possible or desirable to maintain two tracks is?
(a) Main and tail (b) Direct rope (c) Endless rope (d) Gravity 1
121,In main and tail rope haulage the length of the tail rope is.....of the haulage plane?
(a) Equal (b) 1/2 times (c) 2 times (d) 4 times 3
122,The system of rope haulage suitable with least cost to lower the loads to feed
to the haulage at lowest level is?
(a) Direct rope haulage (b) Endless rope haulage
(c) Main tail rope haulage (d) Gravity 4
123,The factor of safety for the rope haulage is?
(a) 10 (b) 9 (c) 6 to 7 (d) 5 to 6 3
124,The weight of the tracks for locomotives of more than 10 te capacity?
(a) 28 kgf/m (b) 18 kgf/m (c) 16 kgf/m (d) 10 kgf/m 1
125,The distance between two adjacent sleepers should not exceed?
(a) 1 m (b) 0.85 m (c) 0.6 m (d) 0.5 m 2
126,For tubs of 1.1 cu.m capacity the rail section should be of minimum weight of?
(a) 28 kgf/m (b) 18 kgf/m (c) 16 kgf/m (d) 10 kgf/m 3
127,The general track guage for 1.1 cu.m tub?
(a) 0.3 m (b) 0.6 m (c) 0.9 m (d) 1 m 2
128,The load on the tub axle; haulage speed; wet or dry condition of the mine
will decide the selection of?
(a) Type of haulage (b) width of the track
(c) Weight and section of the rail (d) Type of ballasting 3
129,The track guage for locomotive is?
(a) 1 to 1.2 m (b) 0.9 to 1 m (c) 1.2 to 1.3 m (d) 0.7 to 0.9 m 1
130,The purpose of the sleeper and ballast in the track is?
(a) Distribute the intense bearing pressure of wheels on the rails over a sufficient area of floor
(b) To strengthen the tracks (c) To prevent the tubs to felldown (d) None 1
131,The size of the ballast used in rail track is?
(a) 30 to 40 mm (b) 40 to 50 mm (c) 50 to 60 mm (d) 60 to 80 mm 3
132,For the speed upto 13 kmph the radius of any curve in a mian haulage road should be?
(a) Not more than 20 times longest rigid wheel base of any vehicle in the train
(b) Not less than 20 times longest rigid wheel base of any vehicle in the train
© Not less than 30 m (d) Not less than 50m 2
133,For bending the rail to suitable curvature the device used is?
(a) Retaining key (b) Jokey (c) Creeper (d) Jim crow 4
134,The safety device consist of steel rail or wooden block pivoted at the end
which is used for arresting backward runaway for tubs is?
(a) Back catch (b) Drop warwick (c) Back stay (d) Stop block 1
135,The safety device consist of wooden beam or block lying across the rails to
prevent backward running of tubs is?
(a) Back catch (b) Drop warwick (c) Back stay (d) Stop block 4
136,The safety device used behind an ascending set of tubs on direct or endless
haulage to arrest runaway of tubs is?
(a) Back catch (b) Drop warwick (c) Back stay (d) Runaway switch 3
137,The safety device used for arresting the forward runaway of tubs is?
(a) Back catch (b) Drop warwick (c) Back stay (d) Runaway switch 2
138,The safety device is used effectivey in case of direct rope haulage in the event of
runaway of set of tubs?
(a) Back stay (b) Dropwarwick (c) Stop block
(d) Stop block with runaway switch 4
139,The safety device used for slow down the loco in locomotives is?
(a) Hydraulic tub retarder (b) Drop warwick
(c) Back stay (d) Runaway switch 1
140,The limiting gradient for the locomotive is?
(a) 1 in 10 (b) 1 in 6 (c) 1 in 15 (d) in 25 3
141,The loco is generally employed on the gradient of?
(a) 1 in 10 (b) 1 in 6 (c) 1 in 15 (d) 1 in 25 4
142,The design of locos are such that the total weight supported by each axle is?
(a) Not more than 10 te (b) Not more than 15 te
© Not more than 5 te (d) Not less than 5 te 3
143,The coefficient of adhesion is coeffcient of static friction between?
(a) Wheels of loco and rails (b) axis and bearings
(c) driving wheels and rails (d) None 1
144,The coefficient of adhesion is if the surface is dry and free of sand?
(a) 0.25 (b) 0.2 (c) 0.15 (d) 0.1 1
146,Theoritical maximum tractive effort of a loco is?
(a) 1/4 or 1/5 th of the total weight of loco (b) 1/8 th of weight of loco
© 1/2 of the weight of loco (d) same as the weight of loco 1
147,The tractive effort varies with the?
(a) directly weight of the train (b) inversely weight of the train
(c) directly with the speed of the train (d) inversely with the speed of the train 4
148,The force required to cause movement is called?
(a) Drawbar pull (b) Tractive effort (c) Running force (d) None 2
149,At starting the coefficient of friction is taken as?
(a) 0.01 (b) 0.0025 (c) 0.1 (d) 0.025 1
150,When running the coefficient of friction is taken as?
(a) 0.01 (b) 0.0025 (c) 0.25 (d) 0.025 2
151,The resistance to motion of loco itself when in motion is called?
(a) COefficient of friction (b) Tractive effort (c) Drawbar pull
(d) Rolling resistance 4
152,The steepest gradient in favour of load in loco is determined by?
(a) Tractive effort required (b) Load on the train
(c) Braking effort (d) Drawbar pull 3
153,The loco can barely stop itself and the wheels begin to skid when the gradient is?
(a) 1 in 15 (b) 1 in 25 (c) 1 in 12 (d) 1 in 14 3
154,The safe distance for brakes in loco is?
(a) 30 m (b) 60 m (c) 90 m (d) 15 m 2
155,The optimaum gradient for the loco is?
(a) 1 in 15 (b) 1 in 25 (c) 1 in 100 (d) 1 in 300 4
156,In flame trap of diesel locomotives the plates have a width of ....mm and
gap of ...mm between two adjacent plates?
(a) 50 ; 0.5 (b) 40 ;0.4 (c) 30 ;0.5 (d) 20 ;0.5 1
157,The diesel oil should have a flash point of not less than?
(a) 50 deg C (b) 60 deg C (c) 65 Deg c (d) 75 deg C 3
158,The maximum percentage of CO in the exhaust gases before they enter the
mine atmosphere is?
(a) 0.02 % (b) 0.2 % (c) 0.3 % (d) 0.4 % 2
159,Diesel locomotives are not allowed where CH4 percentage exceeds....in general body of air?
(a) 0.75 % (b) 1.25 % (c) 0.5 % (d) 1 % 2
160,To remove the oxides and aldehydes from the exhaust gases locomotives are fitted with?
(a) Dust trap (b) Gas collectors (c) Exhaust conditioners (d) None 3
161,In Exhaust conditioner the gases are mixed with about...times thier volume
of fresh ait before being exhausted into ventilating current?
(a) 20 to 30 (b) 30 to 40 (c) 40 to 50 (d) 70 to 80 2
162,In electrical locomotive the battery consist....of the toal weight?
(a) 30 % (b) 40 % (c) 50 % (d) 60 % 4
163,The exhaust gases from the engine amounting in all to about....cu.m per B.H.P per minute?
(a) 0.5 (b) 0.65 (c) 0.85 (d) 0.085 4
164,If the track guage is more than 0.6 m then......... are preffered?
(a) Rhombus pillars (b) Square pillars (c) Rectangle pillars (d) Circular 1
165,The haulage used upto 35 hp is called?
(a) Rope haulage (b) Endless haulage (c) Tugger haulage (d) Gravity haulage 3
166,The limiting gradient for the tugger haulage is?
(a) 1 in 6 (b) 1 in 4 (c) 1 in 10 (d) 1 in 15 1
167,The size of direct rope haulage used underground generally ?
(a) Less than 250 HP (b) Less than 200 HP
(c) Less than 150 HP (d) More than 250 HP 3
168,The direct rope haulage with 150 HP the reasonal output is ?
(a) 1000 te/day (b) 800 te/day (c) 600 te/day (d) 400 te/day 3
169,The maximum length of the rope haulage is?
(a) 1000 m (b) 800 m (c) 600 m (d) 450 m 3
170,High capacity endless rope haulage may give ...?
(a) 1000 te/day (b) 800 te/day (c) 600 te/day (d) 400 te/day 1
171,The maximum length of the endless rope haulage is?
(a) 1000 m (b) 800 m (c) 600 m (d) 450 m 1
172,Limiting gradient for the main and tail rope haulage is?
(a) 1 in 6 (b) 1 in 8 (c) 1 in 10 (d) 1 in 3 4
173,Under favourable conditions diesel locomotives of 10 te may deal with output of?
(a) 2000 te/day (b) 1500 te/day (c) 1000 te/day (d) 600 te/day 2
174,The minimum thickness of the seam for using trolley wire locomotive is?
(a) 1.5 m (b) 1.8 m (c) 2 m (d) 3 m 2
175,To slow down the tubs the device used is?
(a) Runaway switch (b) Back stay (c) Hydraulic tub retardar (d) Sprags 4
176,The maxmimum speed of winding drum shaft is?
(a) 100 rpm (b) 60 rpm (c) 45 rpm (d) 30 rpm 3
177,When two tubs are in tandom the gap between the inner most ends shall not be less than?
(a) 10 cm (b) 20 cm (c) 20 mm (d) 40 mm 2
178,The limiting gradient for the conveyor with rubber coating without breaking arrangement is?
(a) 1 in 3 (b) 1 in 4 (c) 1 in 5 (d) 1 n 6 3
179,The limiting gradient for the conveyor with rubber coating with thrustor breaking
arrangement is?
(a) 1 in 3 (b) 1 in 4 (c) 1 in 5 (d) 1 in 6 1
180,The maximum angle of inclination for conveying coal on piled P.V.C belt is?
(a) 20 deg (b) 18 deg (c) 12 deg (d) 16 deg 4
181,The prefferable speed of the belt conveyor is?
(a) 20 to 30 m/min (b) 30 to 45 m/min
(c) 45 to 60 m/min (d) 45 to 150 m/min 3
182,The maximum width of the belt conveyor is?
(a) 1 m (b) 1.5 m (c) 1.8 m (d) 2 m 2
183,The coal carrying capacity of a tough belt of 650mm wide at a speed of 30 m/min is?
(a) 30 tph (b) 50 tph (c) 70 tph (d) 105 tph 2
184,The coal carrying capacity of a tough belt of 1000mm wide at a speed of 30 m/min is?
(a) 120 tph (b) 50 tph (c) 70 tph (d) 105 tph 4
185,Compared to trough belt the carrying capacity of the flat belt is?
(a) 30 % (b) 40 % (c) 50 % (d) 60 % 3
186,The maximum lump size carried by a belt conveyor is limited to about.....of the belt width?
(a) 40 % (b) 50 % (c) 60 % (d) 75 % 2
187,The inclination of the idlers is?
(a) 10 to 20 deg (b) 20 to 30 deg (c) 30 to 45 deg (d) 45 to 60 deg 2
188,Belt conveyors are extended generally after ....m advance of the roadway?
(a) 90 m (b) 150 m (c) 40 m (d) 60 m 1
189,Loop take up arrangements accomodate extension upto?
(a) 5 m (b) 9 m (c) 20 m (d) 15 m 2
190,Snub pulleys are placed near the drive head?
(a) to increase the arc of contact (b) to increase tension on the belt
© to accomodate more belt for extension (d) for safety 1
191,Usually one motor drives a belt for a roadway of upto ?
(a) 100 m (b) 150 m (c) 200 m (d) 250 m 3
192,Where the series of belt conveyors are used for transpost of coal there shall be?
(a) Remote control (b) Sequence control
(c) Single point control (d) Multipoint control 2
193,The device used to hold the belt to run downward when the power is cutoff is?
(a) Sequence control (b) Back stay (c) Remote control (d) Holdback 4
194,The inbye conveyor cannot be started unless the outbye recieving conveyor is
attained ....of its normal speed?
(a) 40 to 50 % (b) 50 to 60 % (c) 60 to 70 % (d) 70 to 80 % 3
195,The safety in belt conveyors to stop the belt conveyor from any position is?
(a) Sequence control (b) Back stay (c) Remote control (d) Holdback 3
196,The speed of the singel chain conveyor is?
(a) 10 m/min (b) 35 m/min (c) 45 m/min (d) 60 m/min 2
197,The limiting gradient for the scraper chain conveyor is?
(a) 1 in 3 (b) 1 in 4 (c) 1 in 5 (d) 1 n 6 1
198,The limiting length of the scraper chain conveyor is?
(a) 100 m (b) 80 m (c) 60 m (d) 40 m 1
199,The capacity of the scraper chain conveyor is?
(a) 10 to 15 tph (b) 15 to 20 tph (c) 20 to 30 tph (d) 30 to 40 tph 4
200,Armoured chain conveyors are principally used for?
(a) bord and piller (b) In gate roads (c) Prop free front of L/W face (d) On surface 3
201,The vertical flexibility of Armoured chain conveyor is?
(a) 3 to 4 deg (b) 2 to 3 deg (c) 1 to 2 deg (d) 4 to 5 deg 1
202,The horizontal flexibility of Armoured chain conveyor is?
(a) 3 to 4 deg (b) 2 to 3 deg (c) 1 to 2 deg (d) 4 to 5 deg 2
203,The capacity of the A.C.C is?
(a) 100 tph (b) 200 tph (c) 300 tph (d) 50 tph 1
204,The limiting gradient of A.C.C with flights is?
(a) 1 in 3 (b) 1 in 1.5 (c) 1 in 2 (d) 1 in 4 2
205,The limiting gradient of A.C.C without flights is?
(a) 1 in 3 (b) 1 in 1.5 (c) 1 in 2 (d) 1 in 4 1
206,The capacity of the cable belt conveyor is?
(a) 100 tph (b) 200 tph (c) 300 tph (d) 50 tph 3
207,The loading capacity of gate end loaders is?
(a) 1 to 1.5 tph (b) 2 to 4 tph (c) 5 to 7 tph (d) 7 to 9 tph 1
208,The operating length of the shuttle car is?
(a) 100 m (b) 150 m (c) 180 m (d) 250 m 3
209,The traveling speed of the shuttle car with load is?
(a) 3 to 5 kmph (b) 5 to 6 kmph (c) 7 to 8 kmph (d) 8 to 10 kmph 2
210,The traveling speed of the shuttle car without load is?
(a) 3 to 5 kmph (b) 5 to 6 kmph (c) 7 to 8 kmph (d) 8 to 10 kmph 3
211,The limiting gradient for the shuttle car is?
(a) Less than 6 deg (b) less than 12 deg
(c) Less than 20 deg (d) More than 20 deg 1
212,The capacity of the shuttle car is?
(a) 100 tph (b) 200 tph (c) 300 tph (d) 150 tph 4
213,Usual length of the of the chain conveyor with one drive is?
(a) 60 m (b) 90 m (c) 200 m (d) 360 m 2
214,Usual length of the of the chain conveyor with multi drive is?
(a) 60 m (b) 90 m (c) 200 m (d) 360 m 4
215,The dia of the eye in centrifugal pump is....times the impeller dia?
(a) 3 (b) 2 (c) ½ (d) 1/3 4
216,Centrifugal pumps are suitable for low heads upto?
(a) 10 m (b) 20 m (c) 30 m (d) 40 m 2
217,Centrifugal pumps are suitable for water quantities upto?
(a) 2 lac lit/min (b) 3 lac lit/min (c) 4 lac lit/min (d) 5 lac lit/min 3
218,The head developed per stage in centrifugal pump is?
(a) 5 to 10 m (b) 10 to 15 m (c) 15 to 50 m (d) 50 to 60 m 3
219,The total suction lift of a turbine pumps should not exceed?
(a) 2 m (b) 5 m (c) 7 m (d) 9 m 2
220,Turbine pumps are suitable for heads upto?
(a) 20 m (b) 100 m (c) 200 m (d) 50 m 3
221,Turbine pumps are suitable for water quantities upt0?
(a) 1 lac lit/min (b) 50000 lit/min (c) 5000 lit/min (d) 500 lit/min 3
222,The maximum number of impellers on the pump shaft normally does not exceed?
(a) 4 (b) 6 (c) 8 (d) 10 4
223,The valve which is used in the suction pipe to prevent water returning to the pump?
(a) Foot valve (b) Retaining valve (c) BYpass valve (d) Sluice valve 1
224,The valve which is used in delievery column to hold the water if pump stops?
(a) Foot valve (b) Retaining valve (c) BYpass valve (d) Sluice valve 2
225,The valve used for priming before start is?
(a) Foot valve (b) Retaining valve (c) BYpass valve (d) Sluice valve 3
226,The main valve also called as?
(a) Foot valve (b) Retaining valve (c) BYpass valve (d) Sluice valve 4
227,Theoritical suction lift of pump at mean sea level is?
(a) 5 m (b) 10 m (c) 20 m (d) 30 m 2
228,End thrust acts?
(a) towards suction end of the pump (b) towards delievery end of the pipe
© On the impellers of the pipe (d) none 1
229,In balancing disc the loss of energy will be ?
(a) 1 to 2 % (b) 2 to 4 % (c) 4 to 6 % (d) 6 to 8 % 1
230,Balancing disc to countaract the end trust is keyed to ?
(a) Suction end of the shaft (b) Delievery end of the shaft
© Middle of the delievery column (d) Middle of the suction column 2
231,The mechanical efficiency of the pumps may vary from?
(a) 30 to 40 % (b) 40 to 50 % (c) 50 to 60 % (d) 70 to 80 % 4
232,The example of screw pump is?
(a) Centrifugal pump (b) Turbine pump (c) Roto pump (d) Reciprocal pump 3
233,The self priming pump is?
(a) Centrifugal pump (b) Reciprocating pump (c) Roto pump (d) Both 2 and 3 4
234,The pumps most suitable to be used at the working face is?
(a) Roto/Mono pumps (b) Centrifugal (c) Drill pumps (d) Reciprocal 3
235,Suction head of Roto/Mono pump is?
(a) 4 m (b) 5 m (c) 8 m (d) 10 m 3
236,Maximum head of the roto/mono pump is?
(a) 20 m (b) 90 m (c) 120 m (d) 150 m 2
237,The pitch of the stator is....of the rotor in roto pump?
(a) equal (b) twice (c) thrice (d) ½ 2
238,Head per stage in roto pump is?
(a) 30 m (b) 40 m (c) 50 m (d) 60 m 4
239,The velocity of the water in the pipes of the pumps varies?
(a) less than 1 m/s (b) 1 to 2.5 m/sec (c) 2.5 to 4 m/s (d) above 4 m/s 2
240,The diameter of the suction pipe is ....of delievery pipe?
(a) equal (b) twice (c) thrice (d) half 4
241,In small quarries in the coal washaries and for irrigation purpose the pump usd is?
(a) Roto/Mono pumps (b) Centrifugal (c) Turbine (d) Reciprocal 2
242,Steel ropes can be used for winding upto maximum depth of?
(a) 100 m (b) 200 m (c) 300 m (d) 400 m 2
243,In locomotive haulage system at the point of change in gradient the haulage track
should be well graded over a length of?
(a) 12 m (b) 20 m (c) 24 m (d) 30 m 3
244,The driving pulley used in endless rope haulage is?
(a) Snub pulley (b) ig pulley (c) Clifton pulley (d) None 3
245,The marging allowed...m allows a cage to be lifted for materials to be slung beneath it?
(a) 1 to 2 m (b) 2 to 3 m (c) 3 to 7 m (d) 7 to 10 m 3
246,In turbine pump most of the kinetic energy of water is converted into pressure energy is?
(a) Diffuser (b) Volute casing (c) In the eye of the pump (d) None 1
247,The device that is used to relieve the operator of the fatigue and keeps drill pressed
towards exerting and upward lift and foward pressure feed pressure on the drill is?
(a) Drifted (b) Stoped (c) Air leg (d) Rig 3
248,The machine suitable to be used in trimming the faces or in ripping the roof to
save drilling and blasting time and cost is?
(a) Jack hammer (b) Air leg (c) Pneumatic hand pick (d) Drifter 3
249,In most premanant installations with pnematic tools and machines the leakage
should not exceed ...of the total compressor capacity?
(a) 5 % (b) 2 % (c) 7 % (d) 10 % 1
250,The speed of the jackhammer drill is controlled by?
(a) Riffle bar (b) Rachet teeths (c) Throtle valve (d) Blower valve 3
251,The jackhammer drill operated with compressed air at each stroke the drill bit is turned
through.....of the one revolution?
(a) 1 / 4 (b) 1 / 2 (c) 1 / 8 (d) 1 / 12 4
252,The extent of rotation is dependent on the?
(a) Twist in the riffle bar (b) Spacing of rachet teeth
© Both 1 and 2 (d) None of the above 3
253,The number of strokes per min in jack hammer is?
(a) 1500 (b) 2200 (c) 2800 (d) 3500 2
254,The air comsumption is ....cu.m per minute of free air in jack hammer?
(a) 1 to 2 (b) 2 to 3 (c) 3 to 3.5 (d) 4 to 4.5 3
255,The efficiency for electric genarator is .....but for air compressors it is...?
(a) 90 % ; 70 % (b) 70 % ; 90 % (c) 80 % ;50 % (d) 80 % ; 80 % 1
256, The weight of the jack hammer is?
(a) 5 to 10 kgf (b) 10 to 15 kgf (c) 15 to 25 kgf (d) 25 to 40 kgf 3
257,The drill used for upward drilling normally for wet drilling is?
(a) Jack hammer (b) Drifter (c) Stoper (d) Electric drill 3
258,The weight of the coal drill with steel body?
(a) 30 kgf (b) 21.5 kgf (c) 17.5 kgf (d) 15 kgf 2
259,The weight of the coal drill with aluminium body?
(a) 30 kgf (b) 21.5 kgf (c) 17.5 kgf (d) 15 kgf 3
260,Output power of the electric coal drill is?
(a) 1 kw (b) 2 kw (c) 3 kw (d) 4 kw 1
261,The operating voltage of the electric coal drill is?
(a) 30 v (b) 110 v (c) 225 v (d) 660 v 2
262,The electric coal drill is rated?
(a) 2 hrs (b) 1 hr (c) 1/2 hr (d) 1/4 hr 3
263,The rate of penetration of the drill bit with electric coal drill is?
(a) 1 m/min (b) 2 m/min (c) 3 m/min (d) 1.5 m/min 4
264,The electric dill is capable of drilling ....holes each 1.5 m depth in 8 hours shift?
(a) 60 (b) 70 (c) 80 (d) 100 3
265,The speed of the drill rod in coal with electric coal drill is?
(a) 250 rpm (b) 500 rpm (c) 850 rpm (d) 600 rpm 4
266,The speed of the drill rod in stone with electric coal drill is?
(a) 250 rpm (b) 500 rpm (c) 850 rpm (d) 600 rpm 1
267,The cutting angle of the drill rod in electric coal drill is?
(a) 3 deg (b) 30 deg (c) 65 deg (d) 45 deg 2
268,The rake angle of the drill rod in electric coal drill is?
(a) 3 deg (b) 30 deg (c) 65 deg (d) 45 deg 1
269,A cowled fan mounted on the dirll and fins onthe cover are for the purpose of?
(a) Strength (b) Provide cool air to driller
© Bringing down the temparature of the drill (d) Protection 3
270,The power is supplied to the coal drill is the?
(a) 5 core armoured cable (b) 3 core armoured cable
© 4 core screened cable (d) 5 core screened cable 1
271,The speed of the motor of an electric rotary coal drill is reduced by?
(a) Sun and planet gearing (b) Helical gear
(c) Herringbone gearing (d) Bevel gearing 1
272,The shape of the drill rods used in coal drilling with electric drill ....?
(a) Eccentric type (b) Vee type (c) Concentric type (d) None 1
273,Gathering arms are operated in gathering arm loader is?
(a) Twin crank discs (b) Twin crank shafts
(c) Twin motors (d) Connection through conveyor 1
274,The slewing angle in gathering arm loader is ...horizontally to axis either side?
(a) 20 deg (b) 30 deg (c) 45 deg (d) 60 deg 3
275,Limiting gradient for the gathering arm loader is?
(a) 1 in 3 (b) 1 in 5 (c) 1 in 6 (d) 1 in 10 2
276,No of motors are in gathering arm loader is?
(a) 2 (b) 3 (c) 4 (d) 5 4
277,The limiting gradient for the rocker shovel is?
(a) 1 in 3 (b) 1 in 4 (c) 1 in 7 (d) 1 in 8 2
278,The limiting thickness of the seam for the continuous miner is?
(a) 3 m (b) 4 m (c) 5 m (d) 2 m 1
279,The limiting gradient for the continuous miner used in underground is?
(a) 15 deg (b) 20 deg (c) 25 deg (d) 30 deg 1
280,In continuous miner the cutting unit is driven by a water cooled motor of?
(a) 25 kw (b) 75 kw (c) 120 kw (d) 200 kw 3
281,The cutting unit of continuous miner of borer type the gearing is?
(a) Compound wheel type (b) Spur gearing (c) Bevel (d) Sun and planet 2
282,The output from the continuous miner is?
(a) 200 t/day (b) 400 t/day (c) 600 t/day (d) 1000 t/day 3
283,The daily progress with the continuous miner is?
(a) 10 to 20 m (b) 20 to 40 m (c) 40 to 60 m (d) 70 m 2
284,The daily progress with the Roadheader is?
(a) 8 m (b) 10 m (c) 15 m (d) 20 m 1
285,The limiting gradient for the Roadheader is?
(a) 10 deg (b) 15 deg (c) 18 deg (d) 25 deg 3
286,Maximum production rate with Roadheader is....cu.m per hour?
(a) 100 (b) 80 (c) 60 (d) 40 2
287,Permissable length of trailing cable is?
(a) 60 m (b) 90 m (c) 150 m (d) 180 m 2
288,The maximum gradient for tyre mounted machine is ?
(a) 1 in 5 (b) 1 in 4 (c) 1 in 3 (d) 1 in 6 1
289,The maximum gradient for crawler mounted machine with spikes is ?
(a) 1 in 5 (b) 1 in 4 (c) 1 in 3 (d) 1 in 6 2
290,The maximum gradient for crawler mounted machine without spikes is ?
(a) 1 in 5 (b) 1 in 4 (c) 1 in 3 (d) 1 in 6 4
291,The maximum gradient for skid mounted machine is ?
(a) 1 in 5 (b) 1 in 4 (c) 1 in 3 (d) 1 in 6 3
292,The maximum gradient for skid mounted machine with special arrangement is ?
(a) 1 in 5 (b) 1 in 1 (c) 1 in 3 (d) 1 in 6 2
293,The maximum gradient for wheel mounted machine is ?
(a) 1 in 15 (b) 1 in 10 (c) 1 in 3 (d) 1 in 6 1
294,The limiting gradient for the SDL is?
(a) 18 deg (b) 15 deg (c) 10 deg (d) 6 deg 1
295,The maximum height of the seam for the SDL is?
(a) 2 m (b) 2.8 m (c) 3.5 m (d) 2.4 m 2
296,The output per day with the SDL is?
(a) 200 to 500 te (b) 500 to 700 te (c) 100 to 200 te (d) above 700 te 1
297,The limiting gradient for the LHD is?
(a) 1 in 3 (b) 1 in 5 (c) 1 in 7 (d) 1 in 9 3
298,The maximum output of the LHD with 3.5 cu.m per month is?
(a) 25000 (b) 35000 (c) 45000 (d) 15000 2
299,The maximum speed of the LHD when empty is?
(a) 3 to 5 kmph (b) 5 to 8 kmph (c) 8 to 10 kmph (d) 10 to 12 kmph 3
300,The maximum speed of the LHD when loaded is?
(a) 3 to 5 kmph (b) 5 to 8 kmph (c) 8 to 10 kmph (d) 10 to 12 kmph 1
301,The motor capacity of the shearer now a days?
(a) 500 kw (b) 375 kw (c) 1500 kw (d) 1000 kw 2
302,The maximum thickness of the seam that the shearer can work now a days is?
(a) 3 m (b) 4 m (c) 5 m (d) 7 m 3
303,The limiting gradient for the shearer is?
(a) 15 deg (b) 25 deg (c) 35 deg (d) 40 deg 3
304,In permanent cable used to supply the electric power run through the shaft or
incline the moisture of atmosphere is excluded by?
(a) Impregnated paper insulation (b) Tarred jute
© Seamless lead sheath (d) Double armouring 3
305,The permanant cable suspended in vertical shaft should be?
(a) Weather proof (b) Non drain (c) Double armouring (d) Fire proof 2
306,The conductivity of the armouring of permanant cable serving the purpose of
earthing shall have atleast...that power core?
(a) 10 % (b) 20 % (c) 30 % (d) 50 % 4
307,While the face is advanced the cable supplies the power from gate end box to
coal drill is extended through joint box of?
(a) Straight through type (b) inset type (c) flit pin plug type (d) cone type 3
308,In gate end box the leakage protection should work where is a leakage os?
(a) 1 % (b) 5 % (c) 10 % (d) 20 % 2
309,The most common type of flame proof protection is?
(a) Hermitically sealed protection (b) Flange protection
© Hinge protection (d) Open protection 2
310,Intrincically safe circuit or apparatus works on voltage not more than?
(a) 30 v (b) 110 v (c) 220 v (d) 60 v 1
311,Gate end box used to supply electricity of?
(a) 110 v (b) 225 v (c) 550 v (d) 1100 v 3
312,The supply of compressed air alternatively from top and bottom of piston in
jackhammer is caused by the part?
(a) Throtle valve (b) Stem (c) Chunk (d) Pawl and rachet 4
313,The maximum working gradient for coal cutting machine is?
(a) 1 in 3 (b) 1 in 4 (c) 1 in 6 (d) 1 in 10 3
314,The electric cable used for water places is?
(a) Compound insulated (b) Volcanised bitumen insulated cable
© 5 core individually screened cable (d) 5 core collectively screened 1
315,In which test is the steel wire subjected to streching force until it breaks?
(a) Tension test (b) Torsion test (c) Bending test (d) Wrapping test 3
316,In reciprocating pump the fitting is used to ensure uniform flow of water is called?
(a) Foot valve (b) Air vessal (c) Air lock (d) Bye pass valve 2
317,The height of the liquid column in meters produced certian pressure at the bottom
of the pope is known as ?
(a) Total static head (b) Discharge head (c) Head (d) Friction head 3
318,The breaking strength of the locked coil rope is......... if C is rope dia?
(a) 52 C*C (b) 56 C*C (c) 85 C*C (d) 95 C*C 3
319,When the material subjected to repeated stresses cause?
(a) Fatigue (b) Corrosion fatigue (c) Surface embrittlement (d) Kinking 1
320,The ultimate strength of the steel rods is about....kgf/sq.mm?
(a) 65 (b) 85 (c) 100 (d) 120 1
321,By the process of normalising ?
(a) Tensile strength of rope increases (b) Tensile strength of steel rod increases
© The steel rod is drawn into wires (d) The impurities in the steel rod are removed 2
322,Roll rack chainless haulage is used?
(a) Road headers (b) Prop free front faces
(c) Gate roads transportation (d) Shearers 4
323,The component in the winding engine house that stores the energy by speeding up during
periods of light load and delievers it by slowing during the heavy load period is?
(a) Electrical braker (b) Flywheel (c) Electrical gear (d) Additional winding in the system 2
324,Turbine pumps with multi stages are fitted with and differs with centrifugal pump is?
(a) Pressure guage (b) Balancing disc (c) Retaining valve (d) Foot valve 2
325,In long length of haulage system the effective signalling system is by the use of?
(a) High capacity battery (b) 110 v line current
(c) Step down potential transformer (d) Relays 4
326,ALpine miner is mounted on?
(a) Tyres (b) Skid (c) Crawler mounted
(d) Individually operated crawler track 4
327,The compressed air jack hammer will not operate properly on long or shorter
strokes than that for which it is designed the important requirement is?
(a) Length of the piston (b) Length of the shank (c) Length of the rifle bar
(d) Length of the chunk 2
328,Total capacity of motor in AM-50 roadheader is?
(a) 100 kw (b) 155 kw (c) 200 kw (d) 120 kw 2
329,The shape of the drill rod used in stone is?
(a) Diamond section (b) Hexagonal (c) Square section (d) Turbine section 4
330,In deep mines as a safety the capacity of the rope to resist kinetic shock is proportional to ?
(a) Length of rope (b) Diameter of rope
(c) Strength of rope (d) Square of length 1
331,A monocable aerial ropeway is generally preffered?
(a) In flat terrain (b) For large tonnage
(c) In hilly terrains (d) For small distances 3
332,Tub rerailers are placed at intervals?
(a) 100 m (b) 200 m (c) 250 m (d) 300 m 3
333,The difference between the pump centre line to the free discharge level is called?
(a) Head (b) Static discharge head
(c) Static suction lift (d) Total static head 2
334,The fitting common for all the pumps but not required for submersible pumps is?
(a) Suction pipe (b) Delievery pipe (c) Main valve (d) Retaining valve 1
335,The maximum gradient of areal rope in a span is?
(a) 1 in 3 (b) 1 in 5 (c) 1 in 7 (d) 1 in 1 1
336,The limiting gradient of areal rope way in mountain region for monocable is?
(a) 1 in 3 (b) 1 in 5.5 (c) 1 in 7 (d) 1 in 4 2
337,The limiting gradient of areal rope way in mountain region for bicable is?
(a) 1 in 3 (b) 1 in 5.5 (c) 1 in 7 (d) 1 in 4 4
338,The capacity of the areal rope way for monocable over long distance about 100 km is?
(a) 100 tph (b) 200 tph (c) 350 tph (d) 400 tph 2
339,The capacity of the areal rope way for bicable over long distance about 100 km is?
(a) 100 tph (b) 200 tph (c) 350 tph (d) 450 tph 4
340,The life of the areal rope is?
(a) 1 yr (b) 2 yr (c) 3 yr (d) 4 yr 3
341,The rope used for track rope in areal rope way is?
(a) Locked coil (b) Lang's lay (c) Regualar lay (d) Flattened strand 1
342,The rope used for traction rope in areal rope way is?
(a) Locked coil (b) Lang's lay (c) Regualar lay (d) Flattened strand 2
343,When a train of tubs hauled up gradient a back stay is attached to.....of the train ?
(a) Middle tub (b) First tub (c) Last tub (d) The sleeper of the track 3
344,Where Electric battery loco is used in under ground the battery charging station shall close to?
(a) An intake airway (b) the entrance of the district (c) the shaft bottom
(d) last working place 1
345,In designing a hoisting system the properties of rope that are most important are?
(a) Weight per unit and type of rope
(b) Weight per unit length and type of the core of rope
(c) Strand diameter and weight to be hauled
(d) Weight per unit length and breaking strength 4
346,The supply of voltage for electric LHD is?
(a) 110 v (b) 220 v (c) 440 v (d) 1100 v 4
347,What is the normal operating air pressure for pnematically operated machines
in underground is.....psi?
(a) 65 (b) 25 (c) 85 to 100 (d) 100 to 120 3
348,The appropriate function of inter cooled in large multi stage compressor is?
(a) To call the LP air (b) To reduce power consumption
© To drain moisture (d) All the above 4
349,Clifton pulley used in ?
(a) Direct rope haulage (b) Endless rope haulage
© Gravity haulage (d) Main and tail rope haulage 2
350,Friction head of a pump varies proportionally with the?
(a) Square root of the length of the pipe range (b) Square of the length of the pipe range
© Length of the pipe range (d) Thrice the pipe range 3
351,The capacity of the wooden prop?
(a) 6-8 te (b) 10 - 15te (c) 4 - 6 te (d) 15 -20 te 1
352,The capacity of the iron prop?
(a) 10 -15 te (b) 15 -25 te (c) 25-30 te (d) 40 -50 te 3
353,The capacity of the wooden cross bar is?
(a) 1 to 2 te (b) 2 to 4 te (c) 4 to 8 te (d) 8 to 10 te 2
354,The capacity of the safary support is?
(a) 1.5 te (b) 5 te (c) 10 te (d) 4 te 1
355,The capacity of the iron girdar is?
(a) 1.5 te (b) 5 te (c) 10 te (d) 4 te 4