UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS

General Certificate of Education Advanced Level

*6791636055*

PHYSICS 9702/04
Paper 4 A2 Structured Questions May/June 2008
1 hour 45 minutes
Candidates answer on the Question Paper.
No Additional Materials are required.

READ THESE INSTRUCTIONS FIRST

Write your Centre number, candidate number and name on all the work you hand in.
Write in dark blue or black pen.
You may use a soft pencil for any diagrams, graphs or rough working.
Do not use staples, paper clips, highlighters, glue or correction fluid.
DO NOT WRITE IN ANY BARCODES.
For Examiner’s Use
Answer all questions.
You may lose marks if you do not show your working or if you do not use 1
appropriate units.
2
At the end of the examination, fasten all your work securely together.
The number of marks is given in brackets [ ] at the end of each question or part 3
question.
4

10

11

12

Total

This document consists of 22 printed pages and 2 blank pages.

SPA (DR/DR) T43265/4

© UCLES 2008 [Turn over

www.xtremepapers.net
 2

Data

speed of light in free space, c = 3.00 × 10 8 m s –1

permeability of free space, ␮0 = 4␲ × 10 –7 H m–1

permittivity of free space, ε0 = 8.85 × 10 –12 F m–1

elementary charge, e = 1.60 × 10 –19 C

the Planck constant, h = 6.63 × 10 –34 J s

unified atomic mass constant, u = 1.66 × 10 –27 kg

rest mass of electron, me = 9.11 × 10 –31 kg

rest mass of proton, mp = 1.67 × 10 –27 kg

molar gas constant, R = 8.31 J K –1 mol –1

the Avogadro constant, NA = 6.02 × 10 23 mol –1

the Boltzmann constant, k = 1.38 × 10 –23 J K –1

gravitational constant, G = 6.67 × 10 –11 N m 2 kg –2

acceleration of free fall, g = 9.81 m s –2

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 3

Formulae

uniformly accelerated motion, s = ut +
 at 2

v 2 = u 2 + 2as

work done on/by a gas, W = p⌬V

gravitational potential, φ = – Gm
r
hydrostatic pressure, p = ρgh

Nm 2
pressure of an ideal gas, p =
 V
<c >

simple harmonic motion, a = – ω 2x

velocity of particle in s.h.m., v = v0 cos ωt

v = ± ω √(x 20 – x 2)
Q
electric potential, V =
4␲ε0r
capacitors in series, 1/C = 1/C1 + 1/C2 + . . .

capacitors in parallel, C = C1 + C2 + . . .

energy of charged capacitor, W =
 QV

resistors in series, R = R1 + R 2 + . . .

resistors in parallel, 1/R = 1/R1 + 1/R2 + . . .

alternating current/voltage, x = x0 sin ωt

radioactive decay, x = x0 exp(– λt )

0.693
decay constant, λ =
t


© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 4

Section A For
Examiner’s
Answer all the questions in the spaces provided. Use

1 (a) (i) Define the radian.

..................................................................................................................................

..................................................................................................................................

.............................................................................................................................. [2]

(ii) A small mass is attached to a string. The mass is rotating about a fixed point P at
constant speed, as shown in Fig. 1.1.

mass rotating
at constant speed

Fig. 1.1

Explain what is meant by the angular speed about point P of the mass.

..................................................................................................................................

..................................................................................................................................

.............................................................................................................................. [2]

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 5

(b) A horizontal flat plate is free to rotate about a vertical axis through its centre, as shown For
in Fig. 1.2. Examiner’s
Use

plate

M
d

Fig. 1.2

A small mass M is placed on the plate, a distance d from the axis of rotation.
The speed of rotation of the plate is gradually increased from zero until the mass is
seen to slide off the plate.

The maximum frictional force F between the plate and the mass is given by the
expression

F = 0.72W,

where W is the weight of the mass M.

The distance d is 35 cm.

Determine the maximum number of revolutions of the plate per minute for the mass M to
remain on the plate. Explain your working.

number = ........................................... [5]

(c) The plate in (b) is covered, when stationary, with mud.

Suggest and explain whether mud near the edge of the plate or near the centre will first
leave the plate as the angular speed of the plate is slowly increased.

..........................................................................................................................................

..........................................................................................................................................

...................................................................................................................................... [2]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 6

2 (a) Explain qualitatively how molecular movement causes the pressure exerted by a gas. For
Examiner’s
.......................................................................................................................................... Use

..........................................................................................................................................

..........................................................................................................................................

...................................................................................................................................... [3]

(b) The density of neon gas at a temperature of 273 K and a pressure of 1.02 × 105 Pa is
0.900 kg m–3. Neon may be assumed to be an ideal gas.

Calculate the root-mean-square (r.m.s.) speed of neon atoms at

(i) 273 K,

speed = ........................................... m s–1 [3]

(ii) 546 K.

speed = ........................................... m s–1 [2]

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 7

(c) The calculations in (b) are based on the density for neon being 0.900 kg m–3. For
Suggest the effect, if any, on the root-mean-square speed of changing the density at Examiner’s
constant temperature. Use

..........................................................................................................................................

..........................................................................................................................................

...................................................................................................................................... [2]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 8

3 A tube, closed at one end, has a uniform area of cross-section. The tube contains some For
sand so that the tube floats upright in a liquid, as shown in Fig. 3.1. Examiner’s
Use

tube

liquid
d
sand

Fig. 3.1

When the tube is at rest, the depth d of immersion of the base of the tube is 16 cm.
The tube is displaced vertically and then released.
The variation with time t of the depth d of the base of the tube is shown in Fig. 3.2.

17

d / cm

16

15
0 1.0 2.0 3.0
t/s

Fig. 3.2

(a) Use Fig. 3.2 to determine, for the oscillations of the tube,

(i) the amplitude,

amplitude = ........................................... cm [1]

(ii) the period.

period = ........................................... s [1]

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 9

(b) (i) Calculate the vertical speed of the tube at a point where the depth d is 16.2 cm. For
Examiner’s
Use

speed = ........................................... cm s–1 [3]

(ii) State one other depth d where the speed will be equal to that calculated in (i).

d = ........................................... cm [1]

(c) (i) Explain what is meant by damping.

..................................................................................................................................

..................................................................................................................................

..................................................................................................................................

.............................................................................................................................. [2]

(ii) The liquid in (b) is now cooled so that, although the density is unchanged, there is
friction between the liquid and the tube as it oscillates. Having been displaced, the
tube completes approximately 10 oscillations before coming to rest.
On Fig. 3.2, draw a line to show the variation with time t of depth d for the first 2.5 s
of the motion. [3]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 10

4 (a) Define electric potential at a point. For

Examiner’s
.......................................................................................................................................... Use

..........................................................................................................................................

...................................................................................................................................... [2]

(b) Two isolated point charges A and B are separated by a distance of 30.0 cm, as shown in
Fig. 4.1.

30.0 cm

A B

Fig. 4.1

The charge at A is + 3.6 × 10–9 C.

The variation with distance x from A along AB of the potential V is shown in Fig. 4.2.

600

V/V

400

200

0
0 5 10 15 20 25 30
x / cm

–200

–400

–600

Fig. 4.2

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 11

(i) State the value of x at which the potential is zero. For

Examiner’s
x = ........................................... cm [1] Use

(ii) Use your answer in (i) to determine the charge at B.

charge = ........................................... C [3]

(c) A small test charge is now moved along the line AB in (b) from x = 5.0 cm to x = 27 cm.
State and explain the value of x at which the force on the test charge will be maximum.

..........................................................................................................................................

..........................................................................................................................................

..........................................................................................................................................

...................................................................................................................................... [3]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 12

5 A capacitor C is charged using a supply of e.m.f. 8.0 V. It is then discharged through a For
resistor R. Examiner’s
The circuit is shown in Fig. 5.1. Use

8.0V R
C

Fig. 5.1

The variation with time t of the potential difference V across the resistor R during the
discharge of the capacitor is shown in Fig. 5.2.

V/V

0
0 0.5 1.0 1.5 2.0
t/s

Fig. 5.2

(a) During the first 1.0 s of the discharge of the capacitor, 0.13 J of energy is transferred to
the resistor R.
Show that the capacitance of the capacitor C is 4500 µF.

[3]
© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 13

(b) Some capacitors, each of capacitance 4500 µF with a maximum working voltage of 6 V, For
are available. Examiner’s
Use

Draw an arrangement of these capacitors that could provide a total capacitance of

4500 µF for use in the circuit of Fig. 5.1.

[2]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 14

6 A small rectangular coil ABCD contains 140 turns of wire. The sides AB and BC of the coil For
are of lengths 4.5 cm and 2.8 cm respectively, as shown in Fig. 6.1. Examiner’s
Use

pole-piece
of magnet
2.8 cm
B
C

m
5c
4.
A D

axis of rotation

Fig. 6.1

The coil is held between the poles of a large magnet so that the coil can rotate about an axis
through its centre.
The magnet produces a uniform magnetic field of flux density B between its poles.
When the current in the coil is 170 mA, the maximum torque produced in the coil is
2.1 × 10–3 N m.

(a) For the coil in the position for maximum torque, state whether the plane of the coil is
parallel to, or normal to, the direction of the magnetic field.

...................................................................................................................................... [1]

(b) For the coil in the position shown in Fig. 6.1, calculate the magnitude of the force on

(i) side AB of the coil,

force = ........................................... N [2]

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 15

(ii) side BC of the coil. For

Examiner’s
Use

force = ........................................... N [1]

(c) Use your answer to (b)(i) to show that the magnetic flux density B between the poles of
the magnet is 70 mT.

[2]

(d) (i) State Faraday’s law of electromagnetic induction.

..................................................................................................................................

..................................................................................................................................

.............................................................................................................................. [2]

(ii) The current in the coil in (a) is switched off and the coil is positioned as shown in
Fig. 6.1.
The coil is then turned through an angle of 90° in a time of 0.14 s.
Calculate the average e.m.f. induced in the coil.

e.m.f. = ........................................... V [3]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 16

7 The Millikan oil-drop experiment enabled the charge on the electron to be determined. For
Examiner’s
(a) State a fundamental property of charge that was suggested by this experiment. Use

..........................................................................................................................................

...................................................................................................................................... [1]

(b) Two parallel metal plates P and Q are situated in a vacuum. The plates are horizontal
and separated by a distance of 5.4 mm, as illustrated in Fig. 7.1.

plate Q

5.4 mm

plate P

Fig. 7.1

The lower plate P is earthed. The potential difference between the plates can be varied.
An oil droplet of mass 7.7 × 10–15 kg is observed to remain stationary between the
plates when plate Q is at a potential of +850 V.

(i) Suggest why plates P and Q must be parallel and horizontal.

..................................................................................................................................

..................................................................................................................................

.............................................................................................................................. [2]

(ii) Calculate the charge, with its sign, on the oil droplet.

charge = ........................................... C [3]

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 17

(c) The procedure in (b) was repeated for three further oil droplets. The magnitude of For
the charge on each of the droplets was found to be 3.2 × 10–19 C, 6.4 × 10–19 C and Examiner’s
3.2 × 10–19 C. Use

Explain what value these data and your answer in (b)(ii) would suggest for the charge
on the electron.

..........................................................................................................................................

..........................................................................................................................................

...................................................................................................................................... [1]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 18

8 A positron (+10e ) is a particle that has the same mass as an electron and has a charge of For
+1.6 × 10–19 C. Examiner’s
A positron will interact with an electron to form two γ-ray photons. Use

0 + 0 → 2γ
+1e –1e

Assuming that the kinetic energy of the positron and the electron is negligible when they
interact,

(a) suggest why the two photons will move off in opposite directions with equal energies,

..........................................................................................................................................

..........................................................................................................................................

..........................................................................................................................................

..........................................................................................................................................

..........................................................................................................................................

...................................................................................................................................... [3]

(b) calculate the energy, in MeV, of one of the γ-ray photons.

energy = ........................................... MeV [3]

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 19

Section B For
Examiner’s
Answer all the questions in the spaces provided. Use

9 A block diagram for an electronic sensor is shown in Fig. 9.1.

output
device

Fig. 9.1

(a) Complete Fig. 9.1 by labelling the remaining boxes. [2]

(b) A device is to be built that will emit a red light when its input is at +2 V. When the input is
at –2 V, the light emitted is to be green.

(i) On Fig. 9.2, draw a circuit diagram of the device.

input
either + 2V
or – 2V

[2]
Fig. 9.2

(ii) Explain briefly the action of this device.

..................................................................................................................................

.............................................................................................................................. [1]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 20

10 Outline briefly the main principles of the use of magnetic resonance to obtain information For
about internal body structures. Examiner’s
Use

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

.................................................................................................................................................

............................................................................................................................................. [8]

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 21

11 (a) (i) Describe what is meant by frequency modulation. For

Examiner’s
.................................................................................................................................. Use

..................................................................................................................................

.............................................................................................................................. [2]

(ii) A sinusoidal carrier wave has frequency 500 kHz and amplitude 6.0 V. It is to be
frequency modulated by a sinusoidal wave of frequency 8 kHz and amplitude 1.5 V.
The frequency deviation of the carrier wave is 20 kHz V–1.
Describe, for the carrier wave, the variation (if any) of

1. the amplitude,

..................................................................................................................................

.............................................................................................................................. [1]

2. the frequency.

..................................................................................................................................

..................................................................................................................................

..................................................................................................................................

.............................................................................................................................. [3]

(b) State two reasons why the cost of FM broadcasting to a particular area is greater than
that of AM broadcasting.

1 .......................................................................................................................................

..........................................................................................................................................

2 .......................................................................................................................................

...................................................................................................................................... [2]

© UCLES 2008 9702/04/M/J/08 [Turn over

www.xtremepapers.net
 22

12 (a) Optic fibre transmission has, in some instances, replaced transmission using co-axial For
cables and wire pairs. Examiner’s
Optic fibres have negligible cross-talk and are less noisy than co-axial cables. Use

Explain what is meant by

(i) cross-talk,

..................................................................................................................................

..................................................................................................................................

.............................................................................................................................. [2]

(ii) noise.

..................................................................................................................................

..................................................................................................................................

.............................................................................................................................. [2]

(b) An optic fibre has a signal attenuation of 0.20 dB km–1.

The input signal to the optic fibre has a power of 26 mW. The receiver at the output of
the fibre has a noise power of 6.5 µW.
Calculate the maximum uninterrupted length of optic fibre given that the signal-to-noise
ratio at the receiver must not be less than 30 dB.

length = ........................................... km [5]

© UCLES 2008 9702/04/M/J/08

www.xtremepapers.net
 23

BLANK PAGE

9702/04/M/J/08

www.xtremepapers.net
 24

BLANK PAGE

Permission to reproduce items where third-party owned material protected by copyright is included has been sought and cleared where possible. Every
reasonable effort has been made by the publisher (UCLES) to trace copyright holders, but if any items requiring clearance have unwittingly been included, the
publisher will be pleased to make amends at the earliest possible opportunity.

University of Cambridge International Examinations is part of the Cambridge Assessment Group. Cambridge Assessment is the brand name of University of
Cambridge Local Examinations Syndicate (UCLES), which is itself a department of the University of Cambridge.
9702/04/M/J/08

www.xtremepapers.net