Carbon and Low Alloy Steel Valves

ASME Class 150/300/600/900/1500/2500

Gate, Globe and Check Valves, Bolted Bonnet Design
INDEX Profile of KITZ Cast
Carbon Steel Valves
Profile of KITZ Cast Carbon Steel Valves
Standard Product Range................................................01 KITZ’s wide product range helps customers save on
Standard Seat Material and Construction.....................02 procurement costs by reducing the number of
Product Coding...............................................................02 suppliers. It has recently been expanded with the
General Design Specifications........................................03 introduction of low emission service valves that
exceed the US federal environment protection
Valve Shell Materials......................................................03
requirement of a 500 ppm limit on external leakage
KITZ Low Temperature Service Valves...........................03
of toxic gases and chemicals from valves and other
Valve Trim Materials.......................................................03
plant equipment. Every customer is trying hard to
Disc seat and body seat..................................................04
improve their plant life cycle by targeting valve
Stem and bonnet bushing (backseat bushing).............04 maintenance problems as an essential management
Body Seat Rings...............................................................04 program. KITZ’s low emission service valves
Bonnet Gasket Materials................................................05 offered in hydrocarbon and chemical industries a
Contact Face of Flanges..................................................05 realistic and timely solution.
NACE Valves....................................................................05
To compliment its state-of-the-art production
Inspection and Warranty Policy of KITZ Corporation...06
system and facilities, KITZ has committed itself to
Typical KITZ Inspection Flow..........................................06
quality assurance management to the unparalleled
KITZ Low Emission Service Valves..................................07
in the valve industry. Its aggressive employment of
Design Features of KITZ Gate Valve Wedges (Discs).....08 quality management was confirmed by the Bureau
Valve Specifications Veritas Quality International* of London when they

Class Product Code Valve Type Construction Page

chose KITZ for their premiere presentation of the
ISO 9001 certification in 1989, the earliest in the
150 150SCLS Gate B.B., O.S.&Y. 09
valve industry.
300 300SCLS Gate B.B., O.S.&Y. 09
*KITZ has been authorized by the Lloyd's Register Quality Assurance of the United
600 600SCLS Gate B.B., O.S.&Y. 10 Kingdom from 2013.

900 900SCLS Gate B.B., O.S.&Y. 10

1500 1500SCLS Gate B.B., O.S.&Y. 11
150 150SCJS Globe B.B., O.S.&Y. 12
300 300SCJS Globe B.B., O.S.&Y. 12
600 600SCJS Globe B.B., O.S.&Y. 13
900 900SCJS Globe B.B., O.S.&Y. 13
1500 1500SCJS Globe B.B., O.S.&Y. 14
150 150SCOS Check B.C. 15
Field application 1
300 300SCOS Check B.C. 15
600 600SCOS Check B.C. 16
900 900SCOS Check B.C. 16
1500 1500SCOS Check B.C. 17

Through Conduit Gate Valve.........................................18

Machining Field application 2
Pressure Seal Bonnet Valve............................................19
Care for Handling Valves................................................20
Pressure-Temperature Ratings.......................................21

The products introduced in this catalog are all covered

by the ISO 9001 certification awarded KITZ Corporation
in 1989, the earliest in the valve industry. KITZ Ina Plant, Japan KITZ CORPORATION of
(ISO 9001 certified) JIANGSU KUNSHAN
(ISO 9001 certified)
 Standard Product Range

KITZ Cast carbon Steel Valves, RF-flanged*(1), Bolted Bonnet Design

Design Standard Material Nominal 11/2 2 21/2 3 4 5 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36

Valve ASME Size
P-T Wall Page
Type Class *(2) *(3)
Rating Thickness Shell Trim Code 40 50 65 80 100 125 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900

*(4)
150 150SCLS ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 09

300 300SCLS ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 09

API 600
Gate 600 WCB F6/HF 600SCLS ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 10
BS 1414

900 900SCLS ● ● ● ● ● ● ● ● ● ● ● ● 10

1500 1500SCLS ● ● ● ● ● ● ● ● ● ● 11

150 150SCJS ● ● ● ● ● ● ● ● ● ● ● ● ● 12

300 300SCJS ● ● ● ● ● ● ● ● ● ● ● ● 12

ASME API 600

Globe 600 WCB F6/HF 600SCJS ● ● ● ● ● ● ● ● ● 13
B16.34 BS 1873

900 G-900SCJS ● ● ● ● 13

1500 1500SCJS ● ● ● ● ● ● 14

150 150SCOS ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 15

300 300SCOS ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 15

WCB
Swing API 600
600 or F6/HF 600SCOS ● ● ● ● ● ● ● ● ● ● ● ● ● 16
Check BS 1868
A105

900 900SCOS ● ● ● ● ● ● ● ● ● ● 16

1500 1500SCOS ● ● ● ● ● ● ● ● ● ● 17

*(1): Butt-welding end available as an option.

Refer to ‘‘Contact Faces of Flanges’’ on Page 05.
*(2): For special shell materials, refer to ‘‘Valve Shell Materials’’ on Page 03.
*(3): For special trim materials, refer to ‘‘Valve Trim Materials’’ on Page 03.
*(4): Nominal size larger than 36 are available for special orders.

Information on through conduit gate and pressure seal valves are found on Pages 18 and 19, respectively.

01
 Standard Seat Material and Construction

Nominal 11 2 2 21 2 3 4 5 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
Valve Size / /
Type KITZ Product Code
Part 40 50 65 80 100 125 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900

Disc ● ● ● ● ● ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆
150SCLS, 300SCLS
Body Seat ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Disc ● ● ● ● ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆
Gate 600SCLS
Body Seat ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Disc ● ● ● ● ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆
900SCLS, 1500SCLS
Body Seat ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
● ● ● ● ●
Disc ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲
150SCJS, 300SCJS
Body Seat ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Disc ● ● ● ● ▲ ▲ ▲ ▲ ▲
Globe 600SCJS
Body Seat ■ ■ ■ ■ ■ ■ ■ ■ ■

Disc ● ● ● ● ▲ ▲
900SCJS, 1500SCJS
Body Seat ▼ ▼ ▼ ▼ ▼ ▼
● ● ● ● ● ● ●
Disc ◆ ◆ ◆ ◆ ◆ ◆ ◆
◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆
150SCOS, 300SCOS
Body Seat ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Disc ● ● ● ● ● ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆
Swing
Check 600SCOS
Body Seat ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Disc ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆
900SCOS, 1500SCOS
Body Seat ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

● : 13Cr Disc ▲ : Steel Disc-13Cr Deposited Seats

◆ : Cast Steel Disc-13Cr Deposited Seats ▼ : Directly Deposited Hardfacing
■ : Steel Seats-Hardfaced and Welded

PRODUCT CODING

G- 150 SC LS6CY a Valve type code: c Special shell material:

L: Gate valve No code is required for WCB. Refer
J: Globe valve to “Valve Shell Materials” on Page 03,
5 4 1 2 3 O: Swing check valve for special shell materials.
L6DS: Through conduit gate
1 ASME pressure class: (Slab Type) 4 Type of end connection:
150 through 2500 L6DE: Through conduit gate No code is required for RF-flanged ends
(Expanded Type) W: Butt-welding ends.
2 Shell material code: LPS: Pressure seal bonnet gate Refer to “Contact Face of Flanges” on
Carbon and low alloy steel are always JPS: Pressure seal bonnet globe Page 05.
identified as ‘‘SC’’ OPS: Pressure seal cap swing check
b Seat material: 5 Type of valve operation:
3 Other valve specifications: Disc Seat Body Seat No code is required for manual
Code

L S 6C Y
Material Material handwheel operation.
S□ 13Cr HF G : Gear operation.
S□Y HF HF E : Electric actuator operation.
□ : Special shell material code
a b c b

02
 General Design Specifications

Items American Std. British Std.

Bolted Bonnet Pressure Seal Through Conduit BS/ISO 10434 (Gate valve)
Shell wall thickness and general valve design ASME BS 1873 (Globe valve)
API 600 API 6D BS 1868 (Check valve)
B 16.34
Pressure-temperature ratings ASME B16.34 BS EN 1759-1
Face-to-face dimensions
ASME B16.10 API 6D BS EN 558-1
End-to-end dimensions
End flange dimensions
ASME B16.5* BS EN 1759-1
Gasket contact facing
BS/ISO 10434 (Gate valve)
Welding end dimensions ASME B16.25 – BS 1873 (Globe valve)
BS 1868 (Check valve)
*MSS SP-44 for Nominal size 22 and ASME B16.47 Series B for Nominal size 26 and larger, for end flange dimensions.

Valve Shell Materials

Besides ASTM A216 WCB, the standard material, KITZ cast steel valves are optionally available with the materials
listed below:
ASTM Specification CarboMaterial Designation Working Temperature* °F (°C) KITZ code
A216 WCB / A216 WCC Carbon steel −
1000 (538) Maximum
A217 WC1 C–1/2 Mo 1C
A217 WC6 11/4 Cr–1/2 Mo 6C
1100 (593) Maximum
A217 WC9 21/4 Cr–1Mo 9C
A217 C5 5Cr–1/2 Mo 5C
1200 (649) Maximum
A217 C12 9Cr–1Mo 12C
A352 LCB Carbon steel BL
–50 (–46) Minimum
A352 LCC Carbon steel CL
A352 LC1 C–1/2 Mo –75 (–59) Minimum 1L
A352 LC2 21/2 Ni –100 –100 (–73) Minimum 2L
A352 LC3 31/2 Ni –150 –150 (–101) Minimum 3L
For ASTM A351 Austenitic Stainless Steel Valves, refer to KITZ Cat.No.E-150.
*Refer to ASME B16.34 for details of ASTM A216, A217 and A352 Pressure-temperature ratings. (See page 21 for A216 and A217)
The minimum working temperature of ASTM A352 is based on ASME B31.3.

KITZ Low Temperature Service Valves

KITZ Corporation offers Class 150, 300 and 600 API 600 design low alloy steel valves for low temperature service
down to -150°F (-101°C) . Detailed design information is available on request.

Valve Trim Materials

API 600 and BS 1873/1868 specify the following valve components as the valve trim:
Description Gate Valve Globe Valve Check Valve
Disc seat surface ● ● ●
Body seat surface ● ● ●
Bonnet bush (Backseat) ● ● −
Stem ● ● −
Others Internal small parts Lock nut Hinge Pin
Specified by API 600 BS 1873 BS 1868

03
 Disc seat and body seat
Following trims specified in API 600, Table 8, are available in KITZ either as our standard or at your option.
Composition of combination trims, which employs different seating surface materials for disc seat and body seat,
shall be arranged at the manufacturer’s discretion, unless specified in advance.

Combination number Material description Brinell hardness

5. HF / HF 350HB min.
8. 13Cr / HF 250HB min. / 350HB min.
11.* Ni-Cu alloy (Monel) / HF Not specified / 350HB min.
12.* 18Cr-8Ni-Mo (316) / HF Not specified / 350HB min.
14.* 19Cr-29Ni (Alloy 20) / HF Not specified / 350HB min.

*Optionally available.
HF: Co-Cr-W Alloy (Stellite No.6) deposited.

Stems and bonnet bushing (backseat bushing)

ASTM A182 (F6a) is our standard material for stems and bonnet bushing. The other materials including ASTM
A182 (F304), A182 (F316), Monel and Alloy 20 are available on your specific request.

Body Seat Rings

Body seat rings of KITZ cast steel valves are mounted on the valve body by seal welding as shown in the typical
examples of gate valves illustrated below. Unless specifically requested in advance, mounting of body seat rings
shall be made at the manufacturer's discretion. Specify your own method of mounting, noting your purchase
orders with adequate KITZ product code numbers.

SCLS SCLSY
(API Trim8) (API Trim5)

Co-Cr-W Hard Faced

Co-Cr-W Hard Faced
Co-Cr-W Hard Faced
Seal Welding Seal Welding

For KITZ cast steel valves made of ASTM A216 WCB, the standard shell material, disc seats and body seat rings are
provided as follows. (Refer to Page 02 for Product Coding)

KITZ Product Code Standard Disc Seat Standard Body Seat Mounting of Body Seat Rings
F6a or A105 + HF* or
SCLS (Gate)
WCB + 13Cr or A106 Gr. B + HF* or
SCJS (Globe) Seal Welded or Direct HF**
A105 + 13Cr or AISI 1022 + HF* or
SCOS (Check)
CA15 Direct HF**
A105 + HF* or
SCLSY (Gate) A105 + HF* or
A106 Gr. B + HF* or
SCJSY (Globe) WCB + HF* or Seal Welded or Direct HF**
AISI 1022 + HF* or
SCOSY (Check) CA15 + HF*
Direct HF**
* Co-Cr-W AIloy deposited for hard facing.
** Co-Cr-W Alloy is directly deposited on valve body for hard facing.
KITZ Product Code 900SCJS, 900SCJSY, 1500SCJS and 1500SCJSY globe valves employ this hard facing.

04
 Bonnet Gasket Materials
Depending on class ratings and servicing conditions, following gasket materials are available for body/bonnet
flange gaskets of KITZ cast steel valves. Specify your gasket material in purchase order.

Class
fleGasket Materialxible grap
150 300 600 900 1500
Corrugated metal with flexible graphite ●
Ring joint metal ● ● ●
Spiral wound metal, flexible graphite filled ●
Stainless steel inserted flexible graphite ●
Note: Refer to Page 07 for bonnet gaskets used for KITZ Iow emission service valves.

Contact Face of Flanges

ASME B16.5 specifies several different types of contact face of flanges as illustrated below. Among them, KITZ cast
steel valves employ 0.06 RF for Class 150 and 300, and 0.25 RF for higher pressure classes with an optional
employment of ring-joint contact.

Flat Face 0.06 RF* 0.25 RF* Ring Joint

Small M/F** Large M/F** Small T/G*** Large T/G***

RF*: Raised Face M/F**: Male-Female T/G ***: Tongue & Groove

Gasket contact surface finish of end flanges as well as body-bonnet flanges depends on the materials selected for
flange gaskets.

NACE Valves
For servicing sour gases or other Hydrogen Sulfide bearing hydrocarbon fluids, KITZ offers NACE valves made of
component materials specially heat-treated and hardness-controlled in comformity with NACE MR0103, KITZ
Standard, or optionally NACE MR0175 Standard.
Typical NACE material configuration is shown below for KITZ cast steel gate valves. A note should be taken on the
fact that NACE hardness requirement conflicts with the valve trim. KITZ NACE steel valves are available only as a
specified option.
Valve Parts ASTM Specification NACE Hardness
Body/bonnet A216 WCB
Disc A216 WCB or AISI Type 410 or A217 CA15
Disc seat *13Cr deposit or AISI Type 410
≦ HRC 22 (237 HB)
Gland
Stem *AISI Type 410
Bonnet bushing
Body seat surface HF** ≧ 350 HB
A193 B7 −
Bonnet bolts
A193 B7M*** ≦ HRC 22
A194 2H −
Bonnet nuts
A194 2HM*** ≦ HRC 22
*Double tempered. (Three step process) **Co-Cr-W Alloy deposited for hard facing.
***The general requirements conform to NACE MR0175 standard.
The users should be aware that it can be necessary to lower equipment pressure ratings when using SSC-resistant bolt and nut.
Please contact KITZ for more information.

05
 Inspection and Warranty Policy of KITZ Corporation

Every piece of KITZ cast carbon and low alloy steel valves is subjected to 100% pressure test, according to API 598
requirements. Manufacturer’s material test reports and inspection certificates are available on your request, while
each valve is guaranteed for 12 months after installation in service, but not exceeding 18 months after shipment
from the factories of KITZ Corporation.
Various tests and inspections of valves made by KITZ Corporation include the below. Unless otherwise specified, all
KITZ cast steel valves shall be subjected to these testing or inspection methods and evaluation criteria.

Test/Inspection Item Method Evaluation

Chemical composition analysis Relevant ASTM Stds.
Mechanical property test ASTM A370 / E8 Relevant ASTM Stds.
Pressure tests API 598 API 598
Radiographic inspection ASTM E94
Wet magnetic particle inspection ASTM E709 ASME B16.34
Liquid penetrant inspection ASTM E165
Low temperature impact test ASTM A370 / E23 ASTM A352
Dimensional inspection Relevant Valve Stds.
Visual inspection MSS SP-55
Emission test* EPA Method 21 and KITZ Std. KITZ Std.

*Applicable to low emission service valves.

Typical KITZ Inspection Flow

Coating
Casting Machining Assembly Marking
Packaging

Material Random 100% 100% 100%

Inspection Non- Dimensional Pressure Visual
Every Destructive Inspection Tests Inspection
Charge Inspection

100% 100%
Dimensional Operational
Inspection Inspection Random
Emission
Test*
100% 100%
Visual Visual
Inspection Inspection

*Applicable to low emission service valves.

06
 KITZ Low Emission Service Valves

In the United States, the Federal Clean Air Act was dramatically amended in 1990, to realize the new environmental
protection policy of 95% reduction in fugitive emission or leak levels of toxic gases and chemicals from plant
equipment. Promulgated in April, 1994, the new law requires all plants handling the toxic gas specified by the
Environmental Protection Agency, to periodically monitor their plant equipment for detection of leaks exceeding
500 ppm, and repair or replace all defective parts immediately. California has exceeded the Federal law with state
regulation requiring 100 ppm maximum leak level for astonishing 99% reduction of such environmental pollution
for the Northern California Region after 1997.

Our low emission valves, the proud fruits of several years of trial and error at our laboratory, are designed,
engineered, manufactured and tested to now meet the 100 ppm maximum emission level. This is the standard
specification in North America for KITZ flanged and butt-welding end carbon or low alloy steel valves rated Class
150, 300 and 600. In other markets, all these low emission valves are optionally available. Major design
considerations for having upgraded our standard valves to the low emission performers are introduced below.

Gland packing Stuffing box

KITZ’s original ‘‘SEALEVER®’’ flexible graphite packing Maximum 125 RMS surface finish. Cylindricity and
set, consisting of 4 dieformed flexible graphite rings* verticality are precisely controlled according to KITZ
and 2 braided flexible graphite rings, combined with a design and manufacturing standards.
spacer bush for Class 300 and above rated valves.
*US Patent No. 5522603 & 5573253. Other patents registered or pending worldwide.
Plug gaskets for check valves
Class 150/300 : Flexible graphite sheet with stainless steel
Bonnet gaskets (including check valve cover gaskets) insert and permeation protective barrier.
Class 150 : Flexible graphite sheet with stainless steel Class 600 & above : S piral wound metal with flexible
insert or corrugated metal with flexible graphite filled
graphite and permeation protective barrier
for low emission service Product identification
Class 300 : Spiral wound (flexible graphite filler and Stainless steel ID plate with the letters ‘‘LOW
stainless steel hoop) with a stainless steel EMISSION’’ in orange is welded on the bonnet flanges.
inner ring
Class 600 & above : Ring joint metal gasket

Diametrical interface clearance

20 to 32 mils (0.5 to 0.8 mm) : Stem to gland
20 to 32 mils (0.5 to 0.8 mm) : Stem to bonnet bushing
4 to 12 mils (0.1 to 0.3 mm) : Gland to stuffing boxs

Stem
16 to 32 RMS surface finish. Straightness and roundness
are precisely controlled according to KITZ design and
manufacturing standards.

YRT Emission Test Results

In addition to our in-house lab tests and certifications by Lloyd’s Register of Shipping, a third-party perfomance test was carried
out on a KITZ nominal size 6 Class 300 gate valve at Yarmouth Research and Technology, Maine, USA, according to one user’s
testing specifications. The test conditions included an unprecedented 3500 cycle operation of a 99% methane pressurized valve
through thermal cycles at 350˚F (177℃), with the valve stem positioned horizontally to the ground, and the leak level was
monitored at every 100 cycles, from an aluminum foil housing sealed the valve gland area. In spite of these severe test
conditions, the results were in close agreement with findings from the tests made at our laboratory over the last several years.

07
 Design Features of KITZ Gate Valve Wedges (Discs)

Among the four different shapes of wedge gates rec-

ognized by API 600 Paragraph 5.6.1.1 and 5.6.1.2, KITZ has
adopted solid wedges for smaller valves such as nominal
size 2 to 4 of Class 900/1500 gate valves, and flexible
wedges for all other sizes of all pressure classes.

H-shaped flexible wedges are featured with mechanical

flexibility to adjust its own shape following the shape of
the body seats for tightly secured mutual contact. This is
particularly important when larger gate valves are
served in extremely high pressure and temperature,
where temporary deformation of the valve body always
occurs. Operational torque is smaller, seat wear is less
and valve closure is tighter when H-shaped flexible
wedges are adopted.
Side View

Solid wedge Flexible wedge

Front View

Solidly designed KITZ wedge gates are forged or cast

solid, single piece of steel without any welding work.
Specially heat-treated wedges are firmly coupled with
integral T-head of the valve stems, which are also
ruggedly designed and specially heat-treated for the
highest possible durability of stem to wedge connection.
API 600 Paragraph 5.8.8 particularly emphasizes the
importance of the mechanical strength of this
connection.

As another unique feature, KITZ wedge gates are

designed for always accurately maintained concentricity
and carefully lapped for leakfree contact.

Stem-to-Wedge Connection

08
Cast Carbon Steel Gate Valve
Bolted bonnet, Outside screw-and-yoke, Rising stem, Non-rising handwheel, Flexible wedge.

Class 150
Fig End Connections
150SCLS RF-flanged ends.

D
W150SCLS Butt-welding ends.
H
Standard materials of parts
D
Parts Materials
Body ASTM A216 Gr.WCB
Bonnet ASTM A216 Gr.WCB
Stem ASTM A182 Gr.F6a
Gear Operation H
Optional Disc 13Cr/Carbon Steel+13Cr
for Nominal Size
14 to 24 Standard Body seat ring Carbon Steel+HF*
H(open) for 26 & Iarger
Gland ASTM A182 Gr.F6a
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
Bonnet bushing ASTM A182 Gr.F6a
L2 Yoke sleeve ASTM A439 Tp.D2
L1 Butt-welding End L1 Grease nipple Carbon steel
*Hard facing with Co-Cr-W Alloy.
150SCLS G-150SCLS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 11/2 2 21/2 3 4 5 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
Size 40 50 65 80 100 125 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900
in 6.50 7.00 7.50 8.00 9.00 10.00 10.50 11.50 13.00 14.00 15.00 16.00 17.00 18.00 19.00 20.00 22.00 24.00 24.00 26.00 28.00 28.00
L1
mm 165 178 190 203 229 254 267 292 330 356 381 406 432 457 483 508 559 610 610 660 711 711
in − 8.50 9.50 11.14 12.00 15.00 15.86 16.50 18.00 19.76 22.50 24.00 26.00 28.00 30.00 32.00 34.00 36.00 36.00 38.00 40.00 40.00
L2
mm − 216 241 283 305 381 403 419 457 502 572 610 660 711 762 813 864 914 914 965 1016 1016
in 15.2 15.2 17.0 20.1 23.3 25.9 29.9 37.8 45.8 53.6 61.9 66.6 74.3 83.6 91.6 98.1 111.6 118.7 123.4 132.3 141.7 149.0
H
mm 385 385 432 509 592 658 758 958 1162 1362 1572 1692 1888 2123 2326 2497 2835 3015 3135 3360 3600 3785
in 7.9 7.9 7.9 9.8 9.8 11.8 11.8 13.8 15.7 17.7 23.6 23.6 23.6 26.8 26.8 29.9 19.7 23.6 23.6 23.6 23.6 23.6
D
mm 200 200 200 250 250 300 300 350 400 450 600 600 600 680 680 760 500 600 600 600 600 600

Bolted bonnet, Outside screw-and-yoke, Rising stem, Non-rising handwheel, Flexible wedge.

Class 300
Fig End Connections
300SCLS RF-flanged ends.
W300SCLS Butt-welding ends.
D H
Standard materials of parts
D Parts Materials
Body ASTM A216 Gr.WCB
Bonnet ASTM A216 Gr.WCB
H Stem ASTM A182 Gr.F6a
Gear Operation
Optional Disc 13Cr/Carbon Steel+13Cr
for Nominal Size Body seat ring Carbon Steel+HF*
12 to 24
H(open) Standard Gland ASTM A182 Gr.F6a
for 26 & Iarger
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
Bonnet bushing ASTM A182 Gr.F6a
L2 Yoke sleeve ASTM A439 Tp.D2
L1 Butt-welding End L1 Grease nipple Carbon steel
*Hard facing with Co-Cr-W Alloy.
300SCLS G-300SCLS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 11/2 2 21/2 3 4 5 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
Size 40 50 65 80 100 125 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900
in 7.50 8.50 9.50 11.14 12.00 15.00 15.86 16.50 18.00 19.76 30.00 33.00 36.00 39.00 43.00 45.00 49.00 53.00 55.00 60.00 64.00 68.00
L1
mm 190 216 241 283 305 381 403 419 457 502 762 838 914 991 1092 1143 1245 1346 1397 1524 1626 1727
in − 8.50 9.50 11.14 12.00 15.00 15.86 16.50 18.00 19.76 30.00 33.00 36.00 39.00 43.00 45.00 49.00 53.00 55.00 60.00 64.00 68.00
L2
mm − 216 241 283 305 381 403 419 457 502 762 838 914 991 1092 1143 1245 1346 1397 1524 1626 1727
in 16.3 16.3 18.0 20.9 24.3 27.3 31.2 39.9 47.9 56.6 61.5 69.5 76.1 84.1 93.1 100.1 112.0 123.8 131.3 143.7 150.0 153.5
H
mm 413 413 456 530 618 694 793 1014 1216 1458 1563 1766 1932 2137 2364 2542 2845 3145 3335 3650 3810 3900
in 7.9 7.9 7.9 9.8 9.8 11.8 13.8 15.7 17.7 23.6 23.6 23.6 26.8 29.9 29.9 35.8 23.6 23.6 23.6 23.6 23.6 23.6
D
mm 200 200 200 250 250 300 350 400 450 600 600 680 680 760 760 910 600 600 600 600 600 600

09
 Cast Carbon Steel Gate Valve
Bolted bonnet, Outside screw-and-yoke, Rising stem, Non-rising handwheel, Flexible wedge.
Class 600

Fig End Connections

600SCLS RF-flanged ends.
W600SCLS Butt-welding ends.

D H Standard materials of parts

D Parts Materials
Body ASTM A216 Gr.WCB
Bonnet ASTM A216 Gr.WCB
H Stem ASTM A182 Gr.F6a
Gear Operation Disc 13Cr/Carbon Steel+13Cr
Optional
for Nominal Size Body seat ring Carbon Steel+HF*
H(open) 8 to 18
Standard
Gland ASTM A182 Gr.F6a
for 20 & Iarger Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
Bonnet bushing ASTM A182 Gr.F6a
L2 Yoke sleeve ASTM A439 Tp.D2
L1 Butt-welding End L1 Grease nipple Carbon steel
*Hard facing with Co-Cr-W Alloy.
600SCLS G-600SCLS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 2 21/2 3 4 5 6 8 10 12 14 16 18 20 22 24
Size 50 65 80 100 125 150 200 250 300 350 400 450 500 550 600
in 11.50 13.00 14.00 17.00 20.00 22.00 26.00 31.00 33.00 35.00 39.00 43.00 47.00 51.00 55.00
L1
mm 292 330 356 432 508 559 660 787 838 889 991 1092 1194 1295 1397
in 11.50 13.00 14.00 17.00 20.00 22.00 26.00 31.00 33.00 35.00 39.00 43.00 47.00 51.00 55.00
L2
mm 292 330 356 432 508 559 660 787 838 889 991 1092 1194 1295 1397
in 17.6 19.6 21.5 26.3 30.4 35.2 41.9 49.5 57.6 62.7 70.0 81.5 88.8 98.4 107.5
H
mm 446 497 545 667 771 893 1094 1257 1464 1593 1779 2070 2256 2500 2730
in 7.9 9.8 9.8 11.8 15.7 17.7 19.7 23.6 26.8 29.9 29.9 35.8 23.6 23.6 24.0
D
mm 200 250 250 300 400 450 500 600 680 760 760 910 600 600 610

Bolted bonnet, Outside screw-and-yoke, Rising stem, Non-rising handwheel, Solid wedge (Nominal Size 2 to 4) or Flexible wedge (Nominal Size 6& larger).
Class 900

Fig End Connections

900SCLS RF-flanged ends.
D
W900SCLS Butt-welding ends.
H
Standard materials of parts
D Parts Materials
Body ASTM A216 Gr.WCB
Bonnet ASTM A216 Gr.WCB
Stem ASTM A182 Gr.F6a
Gear Operation H
Optional Disc 13Cr/Carbon Steel+13Cr
for Nominal Size Body seat ring Carbon Steel+HF*
H(open)
6 to 12
Standard Gland ASTM A182 Gr.F6a
for 14 & Iarger
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
Bonnet bushing ASTM A182 Gr.F6a
L2 Yoke sleeve ASTM A439 Tp.D2
L1 Butt-welding End L1 Grease nipple Carbon steel
*Hard facing with Co-Cr-W Alloy.
900SCLS G-900SCLS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 2 3 4 6 8 10 12 14 16 18 20 24
Size 50 80 100 150 200 250 300 350 400 450 500 600
in 14.50 15.00 18.00 24.00 29.00 33.00 38.00 40.50 44.50 48.00 52.00 61.00
L1
mm 368 381 457 610 737 838 965 1029 1130 1219 1321 1549
in 14.50 15.00 18.00 24.00 29.00 33.00 38.00 40.50 44.50 48.00 52.00 61.00
L2
mm 368 381 457 610 737 838 965 1029 1130 1219 1321 1549
in 20.5 24.5 27.8 35.4 42.8 50.6 59.0 62.2 69.5 85.8 94.5 105.5
H
mm 520 621 706 900 1087 1285 1498 1581 1830 2180 2435 2680
in 9.8 11.8 13.8 19.7 23.6 26.8 29.9 23.6 23.6 23.6 24.0 24.0
D
mm 250 300 350 500 600 680 760 760 600 600 610 610

10
Cast Carbon Steel Gate Valve
Bolted bonnet, Outside screw-and-yoke, Rising stem, Non-rising handwheel, Solid wedge (Nominal Size 2 to 4) or Flexible wedge (Nominal Size 6& larger).

Class 1500
Fig End Connections
1500SCLS RF-flanged ends.
D H
W1500SCLS Butt-welding ends.
D
Standard materials of parts
Parts Materials
Body ASTM A216 Gr.WCB
Gear Operation Bonnet ASTM A216 Gr.WCB
Optional
for Nominal Size
Stem ASTM A182 Gr.F6a
6 to 12 Disc 13Cr/Carbon Steel+13Cr
Standard
for 14 & Iarger H Body seat ring Carbon Steel+HF*
H(open)
Gland ASTM A182 Gr.F6a
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
Bonnet bushing ASTM A182 Gr.F6a
L2 Yoke sleeve ASTM A439 Tp.D2
L1 Butt-welding End L1 Grease nipple Carbon steel
*Hard facing with Co-Cr-W Alloy.
1500SCLS G-1500SCLS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 2 21/2 3 4 6 8 10 12 14 16
Size 50 65 80 100 150 200 250 300 350 400
in 14.50 16.50 18.50 21.50 27.75 32.75 39.00 44.50 49.50 54.50
L1
mm 368 419 470 546 705 832 991 1130 1257 1384
in 14.50 16.50 18.50 21.50 27.75 32.75 39.00 44.50 49.50 54.50
L2
mm 368 419 470 546 705 832 991 1130 1257 1384
in 22.0 25.4 27.0 30.4 40.6 49.1 58.1 65.2 69.0 51.1
H
mm 559 635 685 772 1031 1248 1475 1656 1750 2060
in 9.8 11.8 13.8 15.7 23.6 26.8 35.8 35.8 23.6 24.0
D
mm 250 300 350 400 600 680 910 910 600 610

11
 Cast Carbon Steel Globe Valve
Bolted bonnet, Outside screw-and-yoke, Rising stem handwheel, Swivel disc.
Class 150

Fig End Connections

D 150SCJS RF-flanged ends.
W150SCJS Butt-welding ends.

D
Standard materials of parts
Parts Materials
D H
Body ASTM A216 Gr.WCB
Bonnet ASTM A216 Gr.WCB
Stem ASTM A276 Tp.403
Gear Operation
Standard for Disc 13Cr/Carbon Steel+13Cr
Nominal Size 8 H
Lock nut ASTM A182 Gr.F6a
larger Hammer-blow
H(open)
Type Handwheel Body seat ring Carbon Steel+HF*
for 6
Gland ASTM A182 Gr.F6a
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
L2 Bonnet bushing ASTM A182 Gr.F6a
L1 Butt-welding End L1 Yoke sleeve ASTM A439 Tp.D2
*Hard facing with Co-Cr-W Alloy.
150SCJS G-150SCJS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 11/2 2 21/2 3 4 5 6 8 10 12 14 16 18
Size 40 50 65 80 100 125 150 200 250 300 350 400 450
in 6.50 8.00 8.50 9.50 11.50 14.00 16.00 19.50 24.50 27.50 31.00 36.00 38.50
L1
mm 165 203 216 241 292 356 406 495 622 698 787 914 978
in − 8.00 8.50 9.50 11.50 14.00 16.00 19.50 24.50 37.50 31.00 36.00 38.50
L2
mm − 203 216 241 292 356 406 495 622 698 787 914 978
in 13.0 13.0 14.9 15.3 18.0 19.1 20.2 24.8 38.4 41.3 43.5 48.2 49.8
H
mm 331 331 379 389 458 484 513 929 975 1049 1106 1224 1275
in 7.9 7.9 9.8 9.8 9.8 11.8 13.8 15.7 19.7 19.7 19.7 23.6 23.6
D
mm 200 200 250 250 250 300 350 500 500 500 500 600 600

Bolted bonnet, Outside screw-and-yoke, Rising stem handwheel, Swivel disc.

Class 300

D
Fig End Connections
300SCJS RF-flanged ends.
W300SCJS Butt-welding ends.

D Standard materials of parts

D H Parts Materials
Body ASTM A216 Gr.WCB
Gear Operation
Bonnet ASTM A216 Gr.WCB
Standard for Stem ASTM A276 Tp.403
Nominal Size 6 larger
H
Hammer-blow Disc 13Cr/Carbon Steel+13Cr
Type Handwheel
for 5 Lock nut ASTM A182 Gr.F6a
H(open) Body seat ring Carbon Steel+HF*
Gland ASTM A182 Gr.F6a
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
L2 Bonnet bushing ASTM A182 Gr.F6a
L1 Butt-welding End L1 Yoke sleeve ASTM A439 Tp.D2
*Hard facing with Co-Cr-W Alloy.
300SCJS G-300SCJS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 11/2 2 21/2 3 4 5 6 8 10 12 14 16
Size 40 50 65 80 100 125 150 200 250 300 350 400
in 9.00 10.50 11.50 12.50 14.00 15.75 17.50 22.00 24.50 28.00 33.00 34.00
L1
mm 229 267 292 318 356 400 444 559 622 711 838 864
in − 10.50 11.50 12.50 14.00 15.75 17.50 22.00 24.50 28.00 33.00 34.00
L2
mm − 267 292 318 356 400 444 559 622 711 838 864
in 14.2 14.2 16.9 17.2 20.0 24.0 38.9 41.9 45.0 46.7 57.1 55.5
H
mm 361 361 428 436 509 610 989 1064 1142 1187 1450 1410
in 7.9 7.9 9.8 9.8 13.8 15.7 17.7 19.7 23.6 23.6 23.6 23.6
D
mm 200 200 250 250 350 400 500 500 600 600 600 600

12
Cast Carbon Steel Globe Valve
Bolted bonnet, Outside screw-and-yoke, Rising stem handwheel, Swivel disc.

Class 600
Fig End Connections
D
600SCJS RF-flanged ends.
W600SCJS Butt-welding ends.
D
Standard materials of parts
Parts Materials
D H Body ASTM A216 Gr.WCB
Bonnet ASTM A216 Gr.WCB
Gear Operation
Stem ASTM A276 Tp.403
Standard for Nominal Size Disc 13Cr/Carbon Steel+13Cr
4 to 12
Hammer-blow
H Lock nut ASTM A182 Gr.F6a
H(Open) Type Handwheel for 3
Body seat ring Carbon Steel+HF*
Gland ASTM A182 Gr.F6a
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
L2 Bonnet bushing ASTM A182 Gr.F6a
L1 Butt-welding End L1 Yoke ASTM A216 Gr.WCB
*Hard facing with Co-Cr-W Alloy.
600SCJS G-600SCJS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 2 21/2 3 4 5 6 8 10 12
Size 50 65 80 100 125 150 200 250 300
in 11.50 13.00 14.00 17.00 20.00 22.00 26.00 31.00 33.00
L1
mm 292 330 356 432 508 559 660 787 838
in 11.50 13.00 14.00 17.00 20.00 22.00 26.00 31.00 33.00
L2
mm 292 330 356 432 508 559 660 787 838
in 16.0 18.7 20.0 35.3 36.6 39.1 44.1 55.9 62.0
H
mm 406 474 508 897 930 993 1121 1420 1575
in 9.8 11.8 13.8 19.7 19.7 19.7 23.6 23.6 24.0
D
mm 250 300 350 500 500 500 600 610 610

Bolted bonnet, Outside screw-and-yoke, Rising stem, Swivel disc.

Class 900
Fig End Connections
900SCJS RF-flanged ends.
D W900SCJS Butt-welding ends.

Standard materials of parts

Parts Materials
Body ASTM A216 Gr.WCB+HF*
Bonnet ASTM A216 Gr.WCB
All Gear
H Operation Stem ASTM A276 Tp.403
Disc 13Cr/Carbon Steel+13Cr
Lock nut ASTM A182 Gr.F6a
Gland ASTM A182 Gr.F6a
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
L2 Bonnet bushing ASTM A182 Gr.F6a
L1 Butt-welding End Yoke ASTM A216 Gr.WCB
*Hard facing with Co-Cr-W Alloy.
G-900SCJS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 3 4 6 8
Size 80 100 150 200
in 15.00 18.00 24.00 29.00
L1
mm 381 457 610 737
in 15.00 18.00 24.00 29.00
L2
mm 381 457 610 737
in 35.4 37.7 46.2 54.4
H
mm 900 957 1173 1381
in 19.7 19.7 23.6 23.6
D
mm 500 500 600 600

13
 Cast Carbon Steel Globe Valve
Bolted bonnet, Outside screw-and-yoke, Rising stem handwheel, Swivel disc.
Class 1500

Fig End Connections

1500SCJS RF-flanged ends.
D
W1500SCJS Butt-welding ends.

D H Standard materials of parts

Parts Materials
Body ASTM A216 Gr.WCB+HF*
Gear Operation for
Standard Nominal Bonnet ASTM A216 Gr.WCB
Size 21/2 and large
Hammer-blow Type Stem ASTM A276 Tp.403
H
Handwheel for 2
Disc 13Cr/Carbon Steel+13Cr
H(open) Lock nut ASTM A182 Gr.F6a
Gland ASTM A182 Gr.F6a
Gland packing Flexible Graphite
Gland flange ASTM A105/A216 Gr. WCB
Handwheel Ductile iron
Gasket See Page 6
Bonnet bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Gland bolt/nut ASTM A576 Gr.1045/A194 Gr.2H
L2 Bonnet bushing ASTM A182 Gr.F6a
L1 Butt-welding End L1 Yoke ASTM A216 Gr.WCB
*Hard facing with Co-Cr-W Alloy.
1500SCJS G-1500SCJS Note: Refer to Page 5&6 for standard seat material and
construction.
Dimensions
Nominal 2 21/2 3 4 6 8
Size 50 65 80 100 150 200
in 14.50 16.50 18.50 21.50 27.75 32.75
L1
mm 368 419 470 546 705 832
in 14.50 16.50 18.50 21.50 27.75 32.75
L2
mm 368 419 470 546 705 832
in 21.3 36.2 38.0 43.4 53.8 55.1
H
mm 540 920 964 1102 1366 1400
in 13.8 19.7 19.7 23.6 23.6 24.0
D
mm 350 500 500 600 600 610

14
Cast Carbon Steel Check Valve
Bolted cover, Swing type disc.

Class 150
Fig End Connections
150SCOS RF-flanged ends.
W150SCOS Butt-welding ends.

Standard materials of parts

Parts Materials
Nominal Size 6 & larger
Body ASTM A216 Gr.WCB
Cover ASTM A105/A216 Gr.WCB
Disc 13Cr/Carbon Steel+13Cr
Disc nut ASTM A194 Gr.8
H Body seat ring Carbon Steel+HF*
Cover bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Arm ASTM A216 Gr.WCB

Gasket See Page 6

Plug ASTM A576 Gr.1045

L2 *Hard facing with Co-Cr-W Alloy.

Note: Refer to Page 5&6 for standard seat material and
L1 Butt-welding End construction.

150SCOS

Dimensions
Nominal 11/2 2 21/2 3 4 5 6 8 10 12 14 16 18 20 24 26 28 30
Size 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 650 700 750
in 6.50 8.00 8.50 9.50 11.50 13.00 14.00 19.50 24.50 27.50 31.00 34.00 38.50 38.50 51.00 51.00 57.00 60.00
L1
mm 165 203 216 241 292 330 356 495 622 698 787 864 978 978 1295 1295 1448 1524
in − 8.00 8.50 9.50 11.50 13.00 14.00 19.50 24.50 27.50 31.00 34.00 38.50 38.50 51.00 51.00 57.00 60.00
L2
mm − 203 216 241 292 330 356 495 622 698 787 864 978 978 1295 1295 1448 1524
in 5.2 6.1 6.6 7.3 8.3 9.4 9.8 11.5 13.4 14.8 16.3 17.9 20.0 23.0 26.4 26.8 28.2 29.9
H
mm 132 156 168 185 210 239 250 293 340 375 415 455 508 585 670 740 810 871

Bolted cover, Swing type disc.

Class 300
Fig End Connections
300SCOS RF-flanged ends.
W300SCOS Butt-welding ends.

Standard materials of parts

Parts Materials
Nominal Size 4 & larger
Body ASTM A216 Gr.WCB
Cover ASTM A105/A216 Gr. WCB
Disc 13Cr/Carbon Steel+13Cr
Disc nut ASTM A194 Gr.8
H
Body seat ring Carbon Steel+HF*
Cover bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Arm ASTM A216 Gr.WCB

Gasket See Page 6

Plug ASTM A576 Gr.1045

L2 *Hard facing with Co-Cr-W Alloy.

Note: Refer to Page 5&6 for standard seat material and
L1 Butt-welding End construction.

300SCOS

Dimensions
Nominal 11/2 2 21/2 3 4 5 6 8 10 12 14 16 18 20 24 28 30
Size 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 750
in 9.50 10.50 11.50 12.50 14.00 15.75 17.50 21.00 24.50 28.00 33.00 34.00 38.50 40.00 53.00 59.00 62.75
L1
mm 241 267 292 318 356 400 444 533 622 711 838 864 978 1016 1346 1499 1594
in − 10.50 11.50 12.50 14.00 15.75 17.50 21.00 24.50 28.00 33.00 34.00 38.50 40.00 53.00 59.00 62.75
L2
mm − 267 292 318 356 400 444 533 622 711 838 864 978 1016 1346 1499 1594
in 5.5 6.5 7.5 8.1 9.1 9.8 11.0 13.0 14.6 16.3 19.3 21.4 23.0 25.4 34.1 36.6 38.4
H
mm 155 164 190 205 230 250 280 330 370 415 491 543 584 645 865 930 975

15
 Cast Carbon Steel Check Valve
Bolted cover, Swing type disc.
Class 600

Fig End Connections

600SCOS RF-flanged ends.
W600SCOS Butt-welding ends.

Standard materials of parts

Parts Materials
Nominal Size 4 & larger
Body ASTM A216 Gr.WCB
Cover ASTM A216 Gr.WCB
Disc 13Cr/Carbon Steel+13Cr
Disc nut ASTM A194 Gr.8
H Body seat ring Carbon Steel+HF*
Cover bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Arm ASTM A216 Gr.WCB

Gasket See page 6

Plug ASTM A576 Gr.1045

L2
*Hard facing with Co-Cr-W Alloy.
Note: Refer to Page 5&6 for standard seat material and
L1 Butt-welding End construction.

600SCOS

Dimensions
Nominal 2 21/2 3 4 6 8 10 12 14 16 18 20 24
Size 50 65 80 100 150 200 250 300 350 400 450 500 600
in 11.50 13.00 14.00 17.00 22.00 26.00 31.00 33.00 35.00 39.00 43.00 47.00 55.00
L1
mm 292 330 356 432 559 660 787 838 889 991 1092 1194 1397
in 11.50 13.00 14.00 17.00 22.00 26.00 31.00 33.00 35.00 39.00 43.00 47.00 55.00
L2
mm 292 330 356 432 559 660 787 838 889 991 1092 1194 1397
in 7.3 8.3 8.8 10.1 13.1 14.7 17.0 20.0 22.4 24.4 25.8 27.8 35.9
H
mm 185 211 224 257 332 372 432 507 568 620 654 733 913

Bolted cover, Swing type disc.

Class 900

Fig End Connections

900SCOS RF-flanged ends.
W900SCOS Butt-welding ends.

Standard materials of parts

Parts Materials
Body ASTM A216 Gr.WCB
Cover ASTM A216 Gr.WCB
Disc ASTM A216 Gr.WCB+13Cr

H Disc nut ASTM A194 Gr.8

Body seat ring Carbon Steel+HF*
Cover bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Arm ASTM A216 Gr.WCB
Gasket See Page 6
Plug ASTM A576 Gr.1045

L2 *Hard facing with Co-Cr-W Alloy.

Note: Refer to Page 5&6 for standard seat material and
L1 Butt-welding End construction.

900SCOS

Dimensions
Nominal 3 4 6 8 10 12 14 16 18 20
Size 80 100 150 200 250 300 350 400 450 500
in 15.00 18.00 24.00 29.00 33.00 38.00 40.50 44.50 48.00 52.00
L1
mm 381 457 610 737 838 965 1029 1130 1219 1321
in 15.00 18.00 24.00 29.00 33.00 38.00 40.50 44.50 48.00 52.00
L2
mm 381 457 610 737 838 965 1029 1130 1219 1321
in 11.5 13.6 17.4 20.6 24.5 28.3 31.3 34.6 37.5 41.0
H
mm 292 346 441 524 621 720 794 880 952 1042

16
Cast Carbon Steel Check Valve
Bolted cover, Swing type disc.

Class 1500
Fig End Connections
1500SCOS RF-flanged ends.
W1500SCOS Butt-welding ends.

Standard materials of parts

Parts Materials
Body ASTM A216 Gr.WCB
Cover ASTM A216 Gr.WCB
Disc ASTM A216 Gr.WCB+13Cr
H Disc nut ASTM A194 Gr.8
Body seat ring Carbon Steel+HF*
Cover bolt/nut ASTM A193 Gr.B7/A194 Gr.2H
Arm ASTM A216 Gr.WCB
Gasket See Page 6
Plug ASTM A576 Gr.1045
L2 *Hard facing with Co-Cr-W Alloy.
Note: Refer to Page 5&6 for standard seat material and
L1 Butt-welding End construction.

1500SCOS

Dimensions
Nominal 2 21/2 3 4 6 8 10 12 14 16
Size 50 65 80 100 150 200 250 300 350 400
in 14.50 16.50 18.50 21.50 27.75 32.75 39.00 44.50 49.50 54.50
L1
mm 368 419 470 546 705 832 991 1130 1257 1384
in 14.50 16.50 18.50 21.50 27.75 32.75 39.00 44.50 49.50 54.50
L2
mm 368 419 470 546 705 832 991 1130 1257 1384
in 11.4 12.4 13.4 15.3 20.2 25.6 29.0 34.4 37.6 42.6
H
mm 292 315 339 388 514 649 737 875 955 1082

17
Through Conduit Gate Valve
Slab gate Valve Expanding Gate Valve

Parts Materials
Body A216 Gr.WCC or A105
Bonnet A216 Gr.WCC
Stem SUS403
Disc A216 Gr.WCC ＋ HF* ＋ A105
Gland Packing Flexible graphite
Gasket Spiral wound flexible graphite
Body Sheet RIng Carbon steel + HF*

Handwheel Ductile Iron

Note: Except for the above trim material, please contact KITZ for more information.
*HF: Hard facing with Co-Cr-W alloy

Product Range
Nominal DN 50 65 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900
Size Valve Type
Fig. NPS 2 21/2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36
150SCL6DSCCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
300SCL6DSCCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
600SCL6DSCCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Slab
900SCL6DSCCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
1500SCL6DSCCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2500SCL6DSCCY ○ ○ ○ ○ ○ ○ ○ ○
150SCL6DECCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
300SCL6DECCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
600SCL6DECCY Expanging ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
900SCL6DECCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
1500SCL6DECCY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
For gear operation specification, please contact KITZ for more information.

■Design standard: API 6D

　P-T Rating: ASME B16.34
■In case of gear operation, “G-”will be put
　before product codes.

18
Pressure Seal Bonnet Valve
Gate Valve Globe Valve Check Valve

Spot Weld
HF

Seal Weld
Seal Weld

HF HF

Parts Materials Parts Materials Parts Materials

Body A216 Gr.WCB A216 Gr.WCB+ Body A216 Gr.WCB
Body
Up to 200A: A105 HF* Cover A105
Bonnet
250A & over: A216 Gr.WCB Bonnet A105 Up to 125A: 105+
Stem SUS403 or OHTARON1 Stem OHTARON1 HF*
Disc
Up to 250A: A105+HF* A182 F11+ 150A and Over: A182 F11+
Disc Disc
300A & over: A216 Gr.WCB+HF* HF* HF*
Gland Packing Flexible graphite Packing Flexible Graphite Gasket Flexible graphite
Gasket Flexible graphite Gasket Flexible Graphite Up to 125A A105+
Body Seat Ring A105+HF* Handwheel SCPH2+SF440A HF*
Body Seat Ring
Handwheel Ductile iron 150A and over: A182 F11+
*HF: Hard facing with Co-Cr-W alloy HF*

Product Range (mm)

Nominal DN 50 65 80 100 150 200 250 300 350 400 450 500 650
Size Valve Type
Fig. NPS 2 21/2 3 4 6 8 10 12 14 16 18 20 24
900SCLSPS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
1500SCLSPS Gate ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2500SCLSPS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
900SCJSPS ○ ○ ○ ○ ○ ○ ○ ○
1500SCJSPS Globe ○ ○ ○ ○ ○ ○ ○ ○
2500SCJSPS ○ ○ ○ ○ ○ ○ ○ ○
900SCOSPS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
1500SCOSPS Check ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2500SCOSPS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
For gear operation specification, please contact KITZ for more information.

■Design Standard: ASME B16.34

　P-T rating: ASME B16.34
■In case of gear operation, “G-”will be put
　before product codes.

19
 Care for Handling Valves

1. Before installing valves: 4. Replacing packing rings:

Before installing valves, be sure that adequate valves It is recommended to replace packing rings during
have been prepared to exactly meet the service valve maintenance operation, but never while the
conditions including the maximum design pressure valve is being pressurized in service, except when the
and temperature. Foreign objects such as sand or line pressure is reduced to the atmospheric level. KITZ
scale may be left in the pipes, and care should be cast carbon and low alloy steel valves are provided
taken to remove all of them by filters or strainers to with the backseats on the bonnet bushing. If leakage
protect valve seat surfaces during subsequent valve from the gland area cannot be stopped by
commissioning. retightening the gland nuts, operate the valve to its
full open position and add a few packing rings or
2. Installing valves: replace packing rings utilizing sealing function of
On mounting valves, clean the inside of pipes again so these backseats.
that no welding spatter, chips, scale or sand are left.
For installation of flanged end valves, flange bolts Sealing function of backseats is sometimes disturbed
should be tightened alternately in a star pattern. due to rust or other foreign objects trapped inside. It
Where extraordinary external forces such as piping should be carefully checked before adding or
stress may be applied to the flanges of valve being replacing packing rings that backseats function
installed, provide valve supports or any other properly. When the valve is highly pressurized, it
adequate protective measures. sometimes causes danger to replace all of packing
rings. In this case, adding a few new rings or replacing
Check body/bonnet bolting during installation, stress a few rings on top of the packing chamber is
relaxation of fasteners can occur during transit and recommended as a first aid solution.
storage. For replacement of packing rings, first remove .the
gland nuts and then packing rings. Clean the packing
Lubricate stem and yoke sleeve prior to valve opera- chamber and the valve stem. After checking that all
tion. KITZ valves are shipped from the factory with sliding parts are in good condition, securely install
only a little lubricant which facilitates assembly. new packing rings. Press new packing rings lightly a
few times with the gland and then evenly tighten the
3. Retightening valves glands: gland nuts.
When leakage is detected from the gland area while
the valve is being in service, the gland nuts should be
immediately retightened. Tighten the gland slowly
and gradually until the leakage stops, while rotating
the valve handwheel. In case the valve operating
torque has been found considerably increased after
these procedures, it is recommended to replace all
packing rings at the time of valve maintenance.

20
 Pressure - Temperature Ratings <For reference only>
Valves - Flanged and Welding End : Standard Class

ASTM Material Standard-to ASME B16.34 2013

Working Pressures by Class, psig

Temperature
Class 150 Class 300 Class 600

WCB WC6 C5 C12 LCC WCB WC6 C5 C12 LCC WCB WC6 C5 C12 LCC
˚F ˚C (a) (b) (c) (c) (d) (a) (b) (c) (c) (d) (a) (b) (c) (c) (d)
-20 to 100 -29 to 38 285 290 290 290 290 740 750 750 750 750 1,480 1,500 1,500 1,500 1,500
200 93 260 260 260 260 260 680 750 750 750 750 1,360 1,500 1,500 1,500 1,500
300 149 230 230 230 230 230 655 720 730 730 730 1,310 1,445 1,455 1,455 1,455
400 204 200 200 200 200 200 635 695 705 705 705 1,265 1,385 1,410 1,410 1,405
500 260 170 170 170 170 170 605 665 665 665 665 1,205 1,330 1,330 1,330 1,330
600 316 140 140 140 140 140 570 605 605 605 605 1,135 1,210 1,210 1,210 1,210
650 343 125 125 125 125 125 550 590 590 590 590 1,100 1,175 1,175 1,175 1,175
700 371 110 110 110 110 110 530 570 570 570 555 1,060 1,135 1.135 1.135 1,110
750 399 95 95 95 95 95 505 530 530 530 505 1,015 1,065 1,065 1,065 1,015
800 427 80 80 80 80 80 410 510 510 510 410 825 1,015 1,015 1,015 825
850 454 65 65 65 65 65 320 485 485 485 320 640 975 975 975 640
900 482 50 50 50 50 50 230 450 375 450 225 460 900 745 900 445
950 510 35 35 35 35 35 135 320 275 375 135 275 640 550 755 275
1000 538 20 20 20 20 20 85 215 200 255 85 170 430 400 505 170
1050 566 20 20 20 145 145 170 290 290 345
1100 593 20 20 20 95 100 115 190 200 225
1150 621 20 20 20 65 60 75 130 125 150
1200 649 15 15 20 40 35 50 80 70 105

Working Pressures by Class, psig

Temperature
Class 900 Class 1500 Class 2500

WCB WC6 C5 C12 LCC WCB WC6 C5 C12 LCC WCB WC6 C5 C12 LCC
˚F ˚C (a) (b) (c) (c) (d) (a) (b) (c) (c) (d) (a) (b) (c) (c) (d)
-20 to 100 -29 to 38 2,220 2,250 2,250 2,250 2,250 3,705 3,750 3,750 3,750 3,750 6,170 6,250 6,250 6,250 6,250
200 93 2,035 2,250 2,250 2,250 2,250 3,395 3,750 3,750 3,750 3,750 5,655 6,250 6,250 6,250 6,250
300 149 1,965 2,165 2,185 2,185 2,185 3,270 3,610 3,640 3,640 3,640 5,450 6,015 6,070 6,070 6,070
400 204 1,900 2,080 2,115 2,115 2,110 3,170 3,465 3,530 3,530 3,520 5,280 5,775 5,880 5,880 5,865
500 260 1,810 1,995 1,995 1,995 1,995 3,015 3,325 3,325 3,325 3,325 5,025 5,540 5,540 5,540 5,540
600 316 1,705 1,815 1,815 1,815 1,815 2,840 3,025 3,025 3,025 3,025 4,730 5,040 5,040 5,040 5,040
650 343 1,650 1,765 1,765 1,765 1,765 2,745 2,940 2,940 2,940 2,940 4,575 4,905 4,905 4,905 4,905
700 371 1,590 1,705 1,705 1,705 1,665 2,665 2,840 2,840 2,840 2,775 4,425 4,730 4,730 4,730 4,630
750 399 1,520 1,595 1,595 1,595 1,520 2,535 2,660 2,660 2,660 2,535 4,230 4,430 4,430 4,430 4,230
800 427 1,235 1,525 1,525 1,525 1,235 2,055 2,540 2,540 2,540 2,055 3,430 4,230 4,230 4,230 3,430
850 454 955 1,460 1,460 1,460 955 1,595 2,435 2,435 2,435 1,595 2,655 4,060 4,060 4,060 2,655
900 482 690 1,350 1,120 1,350 670 1,150 2,245 1,870 2,245 1,115 1,915 3,745 3,115 3,745 1,855
950 510 410 955 825 1,130 410 685 1,595 1,370 1,885 685 1,145 2,655 2,285 3,145 1,145
1000 538 255 650 595 760 255 430 1,080 995 1,270 430 715 1,800 1,655 2,115 715
1050 566 430 430 515 720 720 855 1,200 1,200 1,430
1100 593 290 300 340 480 495 565 800 830 945
1150 621 195 185 225 325 310 375 545 515 630
1200 649 125 105 155 205 170 255 345 285 430

(a) Upon prolonged exposure to temperatures above 800˚F, the carbide phase of steel may be converted to graphite.
Permissible, but not recommended for prolonged use above 800˚F
(b) Use normalized and tempered material only. Permissible, but not recommended for prolonged use above 1100˚F
(c) Use normalized and tempered material only.
(d) Not to be used over 650˚F.

21
 E-170 ＝16

Pressure-temperature ratings and other performance data published in this catalog have
been developed from our design calculation, in-house testing, field reports provided by our
customers and / or published official standards or specifications. They are good only to cover
typical applications as a general guideline to users of KITZ products introduced in this catalog.

KITZ Carbon Steel Paintings are suitable for general service conditions. For Painting used in
severe atmospheres or at elevated temperatures please contact us for recommendations
based on your service environment.

For any specific application, users are kindly requested to contact KITZ Corporation for
technical advice, or to carry out their own study and evaluation for proving the suitability of
these products to such an application. Failure to follow this request could result in property
damage and/or personal injury, for which we shall not be liable.

While this catalog has been compiled with the utmost care, we assume no responsibility for
errors, impropriety, or inadequacy. Any information provided in this catalog is subject to
from-time-to-time change without notice for error rectification, product discontinuation,
design modification, new product introduction or any other cause that KITZ Corporation
considers necessary. This edition cancels all previous issues.

Read the instruction manual carefully before use.

If any products designated as strategic material in the Foreign Exchange and Foreign Trade
Law, Cabinet Order Concerning Control of Export Trade, Cabinet order Concerning Control
of Foreign Exchange and other related laws and ordinances ( Foreign Exchange Laws ) are
exported to any foreign country or countries, an export license issued by the Japanese
Government will be required under the Foreign Exchange Laws.

Further, there may be cases where an export license issued by the government of the United
States or other country will be required under the applicable export-related laws and
ordinances in such relevant countries.

The contract shall become effective subject to the fact that a relevant export license is
obtained from the Japanese Government.

Printed in Japan 1612①KPC