Experion LX

Peer Control Data Interface Implementation Guide

EXDOC-XX84-en-500A
April 2017

Release 500
 Document Release Issue Date
EXDOC-XX84-en-500A 500 0 April 2017

Disclaimer
This document contains Honeywell proprietary information. Information contained herein is to be used solely
for the purpose submitted, and no part of this document or its contents shall be reproduced, published, or
disclosed to a third party without the express permission of Honeywell International Sàrl.
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a purpose and makes no express warranties except as may be stated
in its written agreement with and for its customer.
In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The information
and specifications in this document are subject to change without notice.
Copyright 2017 - Honeywell International Sàrl

2 www.honeywell.com
Contents

1 About this guide ..................................................................................................................................... 5

2 Peer Control Data Interface overview ................................................................................................... 7
2.1 About MODBUS TCP ........................................................................................................................................ 8
2.2 Peer Control Data Integration over FTE ............................................................................................................. 9
2.3 PCDI Library .................................................................................................................................................... 11
2.4 Basic Peer Control Data Interface Block Architecture ..................................................................................... 12
2.5 Safety Manager integration ............................................................................................................................... 13
2.6 Peer Control Data Interface processing characteristics .................................................................................... 14
3 Peer Control Data Interface planning and design ............................................................................. 17
3.1 Peer Control Data Interface requirements ........................................................................................................ 18
3.2 MODBUS system considerations ..................................................................................................................... 19
3.3 Write option selection considerations ............................................................................................................... 20
3.4 Performance considerations .............................................................................................................................. 21
3.5 Safety Manager performance considerations .................................................................................................... 22
4 Peer Control Data Interface installation and upgrades .................................................................... 23
4.1 Experion software installation .......................................................................................................................... 24
4.2 FTE network installation .................................................................................................................................. 25
4.3 Hardware installation ........................................................................................................................................ 26
4.4 Safety Manager software installation ............................................................................................................... 27
4.5 General installation considerations and restrictions ......................................................................................... 28
5 Peer Control Data Interface configuration ......................................................................................... 29
5.1 References ......................................................................................................................................................... 30
5.2 Adding Peer Control Data Interface Device (PCDI_MASTER) Block to a project ........................................ 31
5.3 Device supported commands ............................................................................................................................ 41
5.4 Assigning PCDI_Master Block to Execution Environment ............................................................................. 43
5.5 Adding PCDI Array Request Channel Block to Control Module .................................................................... 45
5.6 Starting Element Index Values .......................................................................................................................... 55
5.7 MODBUS loopback diagnostics and Text Array Request Channel block configuration ................................. 57
5.8 Whole array support ......................................................................................................................................... 58
5.9 Simulation support ............................................................................................................................................ 59
5.10 Loading configuration data to the CEE .......................................................................................................... 60
5.11 PCDI_MASTER Block properties form reference ......................................................................................... 62
5.11.1 Main tab parameters ......................................................................................................................... 62
5.11.2 Module Configuration tab parameters ............................................................................................. 63
5.11.3 Slave Configuration tab parameters ................................................................................................. 64
5.11.4 Module Statistics tab parameters ..................................................................................................... 65
5.11.5 Connection Statistics tab parameters ............................................................................................... 66
5.11.6 Channel Status tab parameters ......................................................................................................... 67
5.11.7 Server History tab parameters .......................................................................................................... 67
5.11.8 Server Displays tab parameters ........................................................................................................ 68
5.11.9 Control Confirmation tab parameters .............................................................................................. 69
5.11.10 Identification tab parameters .......................................................................................................... 70
5.12 Array Request Channel Block properties form reference ............................................................................... 72
5.12.1 Main tab parameters ........................................................................................................................ 72

3
CONTENTS

5.12.2 Configuration tab parameters .......................................................................................................... 72

5.12.3 Scaling/Substitution tab parameters ................................................................................................ 74
5.12.4 Status/Data tab parameters .............................................................................................................. 75
5.12.5 Identification tab parameters ........................................................................................................... 75
5.12.6 Dependencies tab parameters .......................................................................................................... 76
5.12.7 Block pins tab parameters ................................................................................................................ 76
5.12.8 Configuration parameters tab parameters ........................................................................................ 76
5.12.9 Monitoring parameters tab parameters ............................................................................................ 76
5.12.10 Block preferences tab parameters .................................................................................................. 76
5.12.11 Template defining tab parameters .................................................................................................. 76
6 Peer Control Data Interface operation ................................................................................................ 77
6.1 Monitoring Peer Control Data Interface functions through Station displays ................................................... 78
6.1.1 Graphical example of PCDI_MASTER block detail display ............................................................ 78
6.1.2 Graphical example of viewing Last Error on Channel Status tab of PCDI_MASTER block in
Station .................................................................................................................................................... 80
6.1.3 Graphical example of PCDI_MASTER block in system component tree ........................................ 81
6.1.4 Using Station System Status display ................................................................................................. 82
6.1.5 Graphical example of PCDI_MASTER block in Alarm pane of System Status Display ................. 82
6.2 Monitoring PCDI Functions through the Monitoring tab in Control Builder .................................................. 86
6.2.1 Activating/inactivating PCDI_MASTER device ............................................................................... 86
6.2.2 PCDI_MASTER device block icon appearances .............................................................................. 86
6.2.3 Control Module block icon appearances ........................................................................................... 89
6.2.4 Monitoring/Interacting with given component/block ........................................................................ 89
6.2.5 Monitoring PCDI related statistics through C300 block in Monitoring mode .................................. 90
6.2.6 Monitoring PCDI related statistics through CEEC300 block in Monitoring mode ........................... 90
6.3 Initiating Switchover of Redundant Devices .................................................................................................... 92
6.4 Checking license details ................................................................................................................................... 93
6.5 Response to C300 RAM retention restart ......................................................................................................... 94
6.6 PCDI support for checkpoint save/restore functions ........................................................................................ 95
7 Peer Control Data Interface maintenance .......................................................................................... 97
7.1 Periodic checks ................................................................................................................................................. 98
8 Peer Control Data Interface troubleshooting ..................................................................................... 99
8.1 Isolating problems .......................................................................................................................................... 100
8.2 Fault classifications ........................................................................................................................................ 101
8.3 Initial checks ................................................................................................................................................... 102
8.3.1 Checking Control Builder error code reference ............................................................................... 102
8.3.2 Viewing release information log ...................................................................................................... 102
8.3.3 Viewing trace log ............................................................................................................................. 102
8.3.4 Checking version and revision log .................................................................................................. 102
8.3.5 Checking server point build log ....................................................................................................... 103
8.3.6 Checking server point build error log .............................................................................................. 103
8.3.7 Checking error log ........................................................................................................................... 103
8.4 Fixing common problems ............................................................................................................................... 104
8.4.1 Loss of power .................................................................................................................................. 104
8.4.2 Loss of communications .................................................................................................................. 104
8.5 Getting further assistance ............................................................................................................................... 105
8.5.1 Guidelines for requesting support .................................................................................................... 105
9 Notices ................................................................................................................................................ 107

4 www.honeywell.com
1 About this guide

This Guide provides information about using the licensed Peer Control Data Interface (PCDI) function to
interface Honeywell's Safety Manager or third-party peer devices supporting MODBUS TCP communications
with the Experion C300 Controller. It includes planning, installing, configuring, operating, and troubleshooting
type data as well as some general conceptual type data to help understand the purpose of the PCDI function.

Revision history

Revision Date Description

A April 2017 Initial release of the document.

Intended audience
Personnel who are responsible for interfacing Safety Manager or third-party peer devices for peer-to-peer
communications through the peer control data interface with Experion control strategies.

Prerequisite skills
• Familiar with working in a Windows operating environment.
• Familiar with using these Experion applications:
– Configuration Studio
– Control Builder
– Station
– Safety Manager
– Safety Builder
• Familiar with MODBUS TCP communications protocol.

How to use this guide

Choose a topic associated with the task you want to complete on the tree view and just click it to launch the
topic in the view pane.

Related documents
The following are links to related documents for more information about associated functions.
• Control Building Guide
• Control Builder Components Reference
• Control Builder Parameter Reference
• Control Builder Error Codes Reference
• Fault Tolerant Ethernet Overview and Implementation Guide
• Fault Tolerant Ethernet Installation and Service Guide
• Configuration Studio Overview

5
1 ABOUT THIS GUIDE

• Operator's Guide

6 www.honeywell.com
2 Peer Control Data Interface overview

C300 Controller supports peer control data interface (PCDI) for peer device data exchange for process control.
The PCDI communicates with Honeywell's Safety Manager and other Analyzers and Programmable Logic
Controllers (PLCs) that support the MODBUS TCP protocol, including a serial MODBUS protocol through an
off the shelf MODBUS TCP Bridge, over Honeywell's Fault Tolerant Ethernet (FTE) network. The Control
Builder in Experion includes function blocks in its library that let you tailor the peer control data interface to
meet your particular application requirements. You must purchase a PCDI license to use the related functions in
Control Builder and the Experion system.

7
2 PEER CONTROL DATA INTERFACE OVERVIEW

2.1 About MODBUS TCP

The MODBUS TCP is the Transmission Control Protocol/Internet Protocol (TCP/IP) version of the MODBUS
protocol. It facilitates communication between devices connected on an Ethernet TCP/IP network based on a
client/server model that uses the following two types of messages with standard TCP acknowledge in response
to a message.
• MODBUS Request: Client sends this message on the network to initiate a transaction
• MODBUS Response : Server sends this message in response to Client
A MODBUS TCP based communication system can include the following different types of devices.
• MODBUS TCP/IP client and server devices connected to a TCP/IP network.
• Bridge, router, or gateway interconnection device to link the TCP/IP network to a serial line sub-network,
which permits connections to MODBUS serial line client and server end devices.
For more information about MODBUS TCP and MODBUS protocols, visit the MODBUS organization web
site.

8 www.honeywell.com
 2 PEER CONTROL DATA INTERFACE OVERVIEW

2.2 Peer Control Data Integration over FTE

Honeywell's Fault Tolerant Ethernet (FTE) serves as the communications media for C300 Controllers to provide
peer control data interface with Safety Manager and other peer devices.
The Safety Manager connects directly to the FTE network through Yellow and Green cables as shown in the
following figure. However, the current Safety Manager is considered a Non-FTE node.

A peer device connects to either the Yellow or the Green side of the FTE network, as shown in the following
figure. For redundant devices, the common connection configuration is the Yellow side to the primary device
and Green side to the secondary device. For MODBUS remote terminal unit (RTU) peer devices on a serial line
connected to a MODBUS TCP peer Bridge, either FTE side connects to the bridge.
Figure 1: Typical C300 Controller Peer Control Data Interface Topology with Third-Party MODBUS TCP Devices and Bridge

9
2 PEER CONTROL DATA INTERFACE OVERVIEW

10 www.honeywell.com
 2 PEER CONTROL DATA INTERFACE OVERVIEW

2.3 PCDI Library

Beginning in Experion R310, the Library tab in the Experion Control Builder includes the following peer
control data interface (PCDI) library of PCDI device and request/channel function blocks to support
configuration of Safety Manager or third-party MODBUS TCP components with Experion control strategies.

Description

Block Name and Icon

This block represents a Safety Manager, native MODBUS TCP Device
or MODBUS TCP Bridge with serial bus connected MODBUS RTU
devices. It is a stand-alone block that must be assigned to a CEEC300.

The Flag Array Request Channel block allows Boolean access to coils
and discrete data access in associated Safety Manager or MODBUS
TCP device. It is a basic block that must be contained in a Control
Module with channels assigned to applicable PCDI device.
The Numeric Array Request Channel block allows access to registers in
associated Safety Manager or MODBUS TCP device. It is a basic block
that must be contained in a Control Module with channels assigned to
applicable PCDI device.
The Text Array Request Channel block allows access to ASCII text in
associated Safety Manager or MODBUS TCP device. It is a basic block
that must be contained in a Control Module with channels assigned to
applicable PCDI device.

11
2 PEER CONTROL DATA INTERFACE OVERVIEW

2.4 Basic Peer Control Data Interface Block Architecture

As shown in the following illustration, the PCDI_MASTER block serves as the communications bridge between
PCDI Array Request Channel blocks and Safety Manager, peer device or peer bridge with serial line MODBUS
RTUs. You can configure the PCDI_MASTER block to represent a single or redundant Safety Manager, single
or redundant peer (MODBUS TCP) device, or single or redundant peer (MODBUS TCP) bridge. Each
PCDI_MASTER block supports up to 64 PCDI Array Request Channel Blocks. Each peer bridge handles up to
16 serial MODBUS RTU connections. The actual total number of devices supported may be restricted by the
system license details. See the following “Checking license details” on page 93 section for more information.

Figure 2: Simplified PCDI block architecture and signal path

12 www.honeywell.com
 2 PEER CONTROL DATA INTERFACE OVERVIEW

2.5 Safety Manager integration

The PCDI lets you efficiently integrate Honeywell's Safety Manager with C300 Controllers.
Please refer to the Safety Manager integration Guide for more information about integrating Safety Manager
with Experion C300 Controller.

13
2 PEER CONTROL DATA INTERFACE OVERVIEW

2.6 Peer Control Data Interface processing characteristics

The following table summarizes some peer control data interface processing characteristics for the given
function.

Function Processing Characteristic

Scheduling The PCDI_MASTER block is executed every basic cycle (50 milliseconds) prior to the
execution of any Control Modules. Each PCDI_MASTER block has its own EXECSTATE.
The EXECSTATE is Inactive when the block is loaded. You set the EXECSTATE to Active
the same as you would a Control Module after loading.
The PCDI Array Request Channel block is executed at the execution cycle of its container
Control Module. The block does not have its own EXECSTATE. The EXECSTATE of the
Control Module controls the execution state of the PCDI Array Channel block.
The PCDI Array Request Channel block runs in either the triggered or the auto-triggered
mode. In triggered mode, the block submits a request on the positive transition of the input
trigger flag. In auto-triggered mode, the DONE flag is internally looped back to the trigger to
provide for the fastest update rate possible. In this mode, the block is capable of refreshing
data at the same rate as the execution cycle of the containing CM - limited by the response
time of the addressed device
Alarming The PCDI_MASTER block serves as the notification detector for all PCDI related alarms.
The alarms are classified as System Diagnostic Notification ones that map to the System
Alarm category with condition name of DIAG on Experion Alarm Summary, System Status
Display and Event Summary on Station.
The PCDI Array Request Channel blocks will report channel alarms through the
PCDI_MASTER block it is attached to. If an alarm condition no longer exists or the block
becomes inactive or it is deleted, channel alarms will return to normal.
Checkpointing The PCDI_MASTER block and PCDI Array Request Channel blocks supports the standard
checkpoint saves and restores functionality. See the “PCDI support for checkpoint save/
restore functions” on page 95 section for more details.
Redundancy In addition to the redundancy capability of the C300 Controller, peer control data interface
supports two connections to two devices at different IP addresses in the PCDI_MASTER
block. Depending on the connection of the two MODBUS TCP devices, an additional
protection against network failures is possible if one of the devices is connected to the Yellow
side of FTE and the other device to the Green side.
Whole Array Access The PCDI Array Request Channel blocks are designed to read or write array data. Array data
are accessible on a single exposed pin as whole-array data, or on individual pins specified by
array index.
Array data is type specific and supports Flags, Numerics, or Textual data. Control Builder
will only allow connecting array pins of the same types to the data pins of these function
block pins. Array connections can be carried across Control Module boundaries using Named
Parameter connectors for connections between Control Modules.

14 www.honeywell.com
 2 PEER CONTROL DATA INTERFACE OVERVIEW

Function Processing Characteristic

Read/Write The PCDI Array Request Channel block data parameters can be exposed as either Input or
Output pins on the channel blocks. The parameters can also be referenced by name without
the pin being exposed. When used as input pins or referenced by parameter name, the block
will 'Pull' data from the connected block, and write the data to the associated end device.
When the pin is used as an output pin or referenced by parameter name, the data will be read
from the end device and made available to the connected block. An operator can also modify
data by overwriting values in the Monitoring view.
All PCDI Array Request Channel blocks read data from the assigned address range. Blocks
that perform writes will first write and then read the data. The DONE parameter will not be
true until both the read and write part of the cycle are performed. Any errors during the read
part of the cycle will result in a BADPV. Any errors during either the write or the read will
set the ERRORCODE with the error reason. The ERRFL flag will reflect whether the error
condition is still active. The ERRFL will turn off when a successful write/read cycle has
completed. Since the last error message is never cleared, even after a successful read or write,
users must always check the error flag first to confirm that there really is an error.
Write Write of data to a PCDI end device is governed by one of these configurable methods.
• WriteOnDiff: Compares the value to write with the PV (last value read). If they are
different, a write is required.
• WriteAlways: Performs a write regardless of the current value or the value being written.
A read occurs after the write has been completed.
• WriteOnChange: Compares the value to write with the last value written. If they are
different, a write is required.
• WriteAlwaysWriteOnly: Same as WriteAlways. However, a read is not performed after
the write.
• WriteOnChgWriteOnly: Same as WriteOnChange. However, a read is not performed after
the write.
Array Read The read of Modbus arrays configured in PCDI Array Request Channel blocks occur on the
rising edge of the trigger input. If the AUTOTRIGGER configuration parameter is set, then
the next read will occur in the next CM period if the done flag was returned before the
beginning of the next cycle. The done flag will be tested at the beginning of the cycle and the
read will be performed, if the flag is set. The maximum array sizes are all designed to be
delivered in one MODBUS TCP packet. The data returned will be formatted according to the
data type defined by the address range of the PCDI Array Channel block.

15
2 PEER CONTROL DATA INTERFACE OVERVIEW

16 www.honeywell.com
3 Peer Control Data Interface planning and design

Related topics
“Peer Control Data Interface requirements” on page 18
“MODBUS system considerations” on page 19
“Write option selection considerations” on page 20
“Performance considerations” on page 21
“Safety Manager performance considerations” on page 22

17
3 PEER CONTROL DATA INTERFACE PLANNING AND DESIGN

3.1 Peer Control Data Interface requirements

Be sure your Experion LX System meets the following minimum requirements to implement peer control data
interface functions.
• License for peer control data interface components.
• Experion LX Server.
• Experion LX Station and Control Builder.
• Non-Redundant or Redundant C300 Controller with compatible firmware.
• SIM-C300 Controller for simulation support is optional.

18 www.honeywell.com
 3 PEER CONTROL DATA INTERFACE PLANNING AND DESIGN

3.2 MODBUS system considerations

The following are some things you should consider when planning your MODBUS system for peer control data
interface.
• Record the primary and secondary IP addresses for each MODBUS TCP Device.
• Map how you want to set up the MODBUS system in relation to the 64 request channels available per
PCDI_MASTER block and considering that each MODBUS TCP Bridge can have a maximum of 16
MODBUS RTU devices.
• List of MODBUS RTU devices and key properties that will be mapped to the PCDI Array Request Channel
blocks.
• MODBUS RTU devices are addressed from 1 to 247 and 255. A value of 0 (zero) indicates no device is
configured (removes the device). Addresses 248 to 254 are reserved.
• You can configure the PCDI_MASTER block to represent a MODBUS TCP Bridge that can support a
maximum of 16 MODBUS RTU devices.

19
3 PEER CONTROL DATA INTERFACE PLANNING AND DESIGN

3.3 Write option selection considerations

You can select how the Array Request Channel block will handle writes to its 'data' parameter through the
configuration of the Write Option (WRITEOPT) parameter on the block's configuration form in Control
Builder. The following table lists some things to consider when making the Write Option selection.

If Data Characterization Requirements Are That . . . Then, Consider This . . .

Multiple elements change before a request block DONEFL The WriteAlways or WriteAlwaysWriteOnly selection will be
becomes TRUE and all elements have an input pin. the most efficient. This function has the possibility of
transferring larger messages, but because the elements will
be contiguous, they can be transferred in a single multiple
write message. If the device does not support multiple
element writes, this will be the most expensive function,
since every element will be transferred with a separate write
message.
The input data rarely changes. The WriteOnChange or WriteOnChangeWriteOnly mode is
probably a good option. If multiple element writes are
supported, all contiguous elements that have changed will
be transferred in single multi-element write messages.
Multiple messages will be required, if there are breaks in the
indexes that have changed.
The device data being read may change independent of The WriteOnDiff selection is the best function.
values written, and it is desired to force the device value to
the input value.

20 www.honeywell.com
 3 PEER CONTROL DATA INTERFACE PLANNING AND DESIGN

3.4 Performance considerations

The following table lists some C300 and MODBUS performance related data for general planning purposes.
This information is subject to change without notice.

C300 Controller1
Number of PCDI_MASTER blocks per C300 Controller 8 maximum (One block per connected Safety Manager, peer
device or peer bridge.)
Number of Serial MODBUS RTUs per C300 Controller 128 maximum (16 devices maximum per MODBUS TCP
Bridge times 8 MODBUS TCP Bridges maximum per C300
Controller.)
Number of Channels per PCDI_MASTER block 64 maximum
Bytes per Second per Channel 256
Message per Second 1 (A maximum message is 256 bytes.)
Performance Estimate2

MODBUS3
Byte Rate

Maximum Packet Size for Reads 256 bytes for all function codes (The request packet is 6
bytes long.)
Maximum Packet Size for Writes 256 bytes (The acknowledgement packet is 6 bytes long.)
Maximum Packet Size Rate

Rate per Request Baudrate * 2915 + device processing time

Maximum Data Delivery Takes into account a single Array Request Channel block at
50 milliseconds. The maximum rate would be 64 times this
rate.
Notes:
1. The use of write on change or write on difference for arrays of flags or numerics will have an effect on C300
performance due to the number of requests that will be queued. The individual elements of the array that change will
each generate a request. The calculation of the impact on the C300 execution units must include the maximum number
of writes that will occur for array writes. To minimize the C300 impact, write always for arrays should be used.
However, this will have a negative impact on serial MODBUS connections due to the write of data that is identical to
what is already in the MODBUS device.
2. The use of write on change or write on difference for arrays of flags or numerics will have an effect on performance
due to the number of requests that will be queued. The individual elements of the array that change will each generate
a request. The performance of the low speed MODBUS serial bus will be impacted by the write of a whole array where
only some elements change.

21
3 PEER CONTROL DATA INTERFACE PLANNING AND DESIGN

3.5 Safety Manager performance considerations

The following table lists some Safety Manager performance related data for general planning purposes. This
information is subject to change without notice.

Safety Manager Communications Performance

Maximum Number of parameters that can be Read from Safety Manager by C300 Unlimited PPS 1
Maximum Number of parameters that can be Written to Safety Manager from 64 per cycle 2
C300 (single writes exclusively)
Maximum Number of parameters that can be Written to Safety Manager from 592 bytes per cycle 2
C300 (block writes exclusively)
Bandwidth usage formulas for a mixture of single writes and block writes (time See equations below table
and size are the key constraints)
Notes:
1. Safety Manager multi-processor architecture enables support of an unlimited number of reads.
2. 'Cycle' refers to the Safety Manager application cycle.

To avoid overruns, writes to Safety Manager must be kept within the following limits:

and

Where:
Single = a single write command
Mblock = marker or coil block write command
Rblock = register block write command
Note that the minimum number of bytes written per message is 4.

22 www.honeywell.com
4 Peer Control Data Interface installation and upgrades

Related topics
“Experion software installation” on page 24
“FTE network installation” on page 25
“Hardware installation” on page 26
“Safety Manager software installation” on page 27
“General installation considerations and restrictions” on page 28

23
4 PEER CONTROL DATA INTERFACE INSTALLATION AND UPGRADES

4.1 Experion software installation

The Peer Control Data Interface is provided as part of the Experion R310 software. Refer to the Experion
Software Installation User's Guide for details about installing the Experion software.

24 www.honeywell.com
 4 PEER CONTROL DATA INTERFACE INSTALLATION AND UPGRADES

4.2 FTE network installation

Refer to the Fault Tolerant Ethernet Installation and Service Guide for information about installing a FTE
network. It is beyond the scope of this document to cover specific FTE installation details.

25
4 PEER CONTROL DATA INTERFACE INSTALLATION AND UPGRADES

4.3 Hardware installation

Refer to the applicable Honeywell or vendor component documentation for details about installing any Experion
control hardware or MODBUS TCP related hardware.

26 www.honeywell.com
 4 PEER CONTROL DATA INTERFACE INSTALLATION AND UPGRADES

4.4 Safety Manager software installation

The Peer Control Data Interface support is provided as part of the Safety Manager R130 software. Refer to the
Safety Manager Installation and Upgrade Guide for details about installing Safety Builder software.

27
4 PEER CONTROL DATA INTERFACE INSTALLATION AND UPGRADES

4.5 General installation considerations and restrictions

The following table lists some general considerations and/or restrictions related to a given installation function.

Function Consideration/Restriction
Network Connection You may connect peer devices to Level 2 configured FTE network ports, just as you would an
Experion server or console. You must configure the devices for 100 megabit full duplex
operation. Avoid using bridges or end devices that can only run at 10 megabits. For redundant
bridges or end devices, we recommend connecting one device to the Yellow switch side and
one to the Green switch side of FTE. If devices have built in network redundancy, connect
one cable to Yellow and one to Green.
Be aware that the current Safety Manager (SM) is a Non-FTE node. This means that SM may
demonstrate single node connection behavior in a redundant topology in response to a FTE
network problem, such as a break in the crossover cable.
IP Address Assignments Follow IP address rules for either Level 1 or Level 2, depending on where the device is
connected.
Serial MODBUS RTU You must connect serial MODBUS RTU devices on a serial bus, such as RS232, RS422/
Connections RS485 full duplex, or RS485 half duplex, to the C300 MODBUS TCP subsystem through a
bridge device. You must connect these devices in a daisy chain manner. A terminator may be
required possibly at each end depending on the number of devices and the total length of the
connecting cables.

28 www.honeywell.com
5 Peer Control Data Interface configuration

Related topics
“References” on page 30
“Adding Peer Control Data Interface Device (PCDI_MASTER) Block to a project” on page 31
“Device supported commands” on page 41
“Assigning PCDI_Master Block to Execution Environment” on page 43
“Adding PCDI Array Request Channel Block to Control Module” on page 45
“Starting Element Index Values” on page 55
“MODBUS loopback diagnostics and Text Array Request Channel block configuration” on page 57
“Whole array support” on page 58
“Simulation support” on page 59
“Loading configuration data to the CEE” on page 60
“PCDI_MASTER Block properties form reference” on page 62
“Array Request Channel Block properties form reference” on page 72

29
5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.1 References
If you have never used Control Builder to build an Experion control strategy, please refer to the Control
Building User's Guide for more information about using the application to build a control strategy.
Refer to the following documents for more details about individual parameters and function blocks.

• Control Builder Parameter Reference

• Control Builder Components Reference
• Control Builder Error Codes Reference

30 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.2 Adding Peer Control Data Interface Device (PCDI_MASTER) Block to a

project
You can only view PCDI_MASTER blocks in the Project tab set for Assignment view. The Assignment view
shows the relationship among all blocks while the Containment view only shows templates that contain other
templates or Control Modules (CM), Sequential Control Modules (SCM), and basic blocks. To toggle the view,
right-click in an open area of the tab window and select Assignment View or Containment View from the list,
as applicable.
Each PCDI_MASTER block is automatically assigned a unique default tag name when it is created. If your
system will include multiple PCDI_MASTER blocks, you may want to adopt a more structured syntax for
naming them.
The block tag or module name must be unique to identify the block in the system. It must contain at least one
letter (A-Z) and can be up to 16 characters long. Note that most special characters (such as +, \, =, /, #, etc.) and
spaces are not allowed.
The item name can be up to 40 characters long and must contain at least one letter (A-Z). It is a name by which
an entity is known within the context of the enterprise model. The Item name must be unique among children of
the same containment parent in the Enterprise Model Builder hierarchy and should conform to the standard
convention names within the system.
The module description text can be up to 132 characters long and appears on both detail and group displays.
The PCDI_MASTER block icon changes appearance in Project based upon the device type it is configured to
represent.
The current Peer Control Data Interface function does not support MODBUS end device configuration.
The Keep Alive functionality is a TCP setting that attempts to use the same socket connection for multiple
requests. Keeping socket connections in use instead of releasing them after use can result in reduced network
traffic.
For redundant peer devices, the same Unit ID is applied to both the primary and secondary devices.
The Unit ID field carries the MODBUS slave address of the remote device, when addressing a device on a
MODBUS+ or MODBUS serial line sub-network through a Bridge. It identifies the slave device connected on
the sub-network behind the bridge. The destination IP address identifies the bridge itself and the bridge uses the
MODBUS Unit ID to forward the request to the right slave device.
The PCDI_MASTER block initiates connection attempts and monitors device connection state. It establishes
connections to the configured primary and secondary devices by setting the desired connection state and
signaling the Requestor task when a connection activity is required. It monitors the status of pending requests
for the Unit IDs configured for its MODBUS TCP device. The PCDI_MASTER controls retries of pending
requests as well as times out the request once all retries have failed.
The PCDI_MASTER block monitors a timestamp value for each configured MODBUS Unit ID. The timestamp
is updated whenever there is a request sent for the specific unit. If the elapsed period from the last activity to the
current time exceeds the LOOPRATE parameter time, the PCDI_MASTER block submits a diagnostic request.
This requires one request per serial device be allocated by the PCDI_MASTER block during initialization.
The following table summarizes how Test Mode (LOOPMODE) and Data Change (LOOPDATACHG)
parameter configuration combine to determine how data is evaluated.

If Test Mode1 (LOOPMODE) And, Data Change2 Then, Data Evaluation . . .

Is . . . (LOOPDATACHG) Is . . .
ReadOnly No Change Verifies that returned data value matches the Data value
specified.
Any Value Checks for a successful read but does not verify the
content.

31
5 PEER CONTROL DATA INTERFACE CONFIGURATION

If Test Mode1 (LOOPMODE) And, Data Change2 Then, Data Evaluation . . .

Is . . . (LOOPDATACHG) Is . . .
Increment or Invert For Coil or Discrete Input: Same as Any Value, since it
would be impossible to synchronize reads with a
changing target device value.
For Holding and Input Registers: Looks for a value
different from the last read value.
Write/Read No Change Always writes the same value and expects the same
value back from the read.
Any Value Only validates that a successful read occurred.
Increment Increments the value to write and then check for the
result to read.
Invert Inverts the last value written and then checks for the
result.
1. For Type (LOOPTYPE) Diag Loopback Test Mode does not matter. It sends a 08/00 (diagnostic - return query data)
command and checks the echoed result. For Types Comm Event Log, Exception Status, and Diag Register, Test Mode
does not matter. They are always Read Only. The Comm Event Log and Exception Status Types will format the
resulting data into a report string, which will be displayed in the Slave Device Definitions grid, Unit ID, Data field for
MODBUS RTU devices or in the Primary Data/Secondary Data fields for native devices.
2. The Diag Register Type can be queried and checked using the Data Change and Data value. Safety Manager has
integrated support for this feature. Test Mode, Data, and Data Change options have no affect for Safety Manager when
the Type selected is Diag Register.

Prerequisites
• Your Experion server is running R310 or greater software.
• You have started Configuration Studio and launched the Control Builder application.
• You have logged on with sufficient privileges to create control strategies using Control Builder.
• If applicable, you have configured the applicable IP addresses when you set up your FTE network.

To add PCDI_MASTER block to a project

1 On the Library tab, click the plus sign for the PCDI library to expand the tree. Drag and drop the
PCDI_MASTER block icon from the library to the Project tab.
2 In the open Name New Function Block(s) dialog, you can either:
• Key in a new Tag Name in its Destination box and/or a new Item Name in its Destination box and click
the Finish button to close the dialog and save the name changes. Or,
• Click the Finish button to close the dialog and accept the default Tag Name and blank Item Name
entries.

32 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

3 Check that the named PCDI_MASTER block icon is now present in the Unassigned directory in the Project
tab.

4 If you want to assign the PCDI_MASTER block to a C300 execution environment (CEEC300) now before
configuring it, go to the following “Device supported commands” on page 41 section before continuing.
5 Go to the next section To configure PCDI_MASTER block in Project to continue with this procedure.

To configure PCDI_MASTER block in a project

1 Right-click the named PCDI_MASTER block icon and select Module Properties from the list to call up the
block's Properties form for configuration.
• You can skip Steps 1 and 2, if you have already entered the desired Module Name and Item Name for the
device.
2 If you want to change the default module name, double-click the Module Name box to highlight it and key
in the desired module name. Click the cursor in the Item Name box. Otherwise, go to Step 3.
3 With cursor in the Item Name box, key in the name of the item this object will be associated with in the
Enterprise Model Builder hierarchy.

Attention
Be aware that changing the Device Type selection can clear any previously entered configuration data, since
device related defaults are reset.

33
5 PEER CONTROL DATA INTERFACE CONFIGURATION

4 Click the down-arrow in the Device Type (DEVTYPE) box and select the Safety Manager or peer device
from the list that this PCDI_MASTER block is to represent.

5 The Currently Assigned Channels list box is read only. It is automatically populated when a PCDI Array
Request block is assigned to it.
6 Click the Module Configuration tab to display it.
7 With cursor in Primary IP Address (PRIMIP) box, key in the IP address for the primary or non-redundant
device this block represents.
8 Click the <Tab> key to move the cursor to the Primary TCP Port (PRIMTCP) box. All MODBUS/TCP
application data unit (ADU) are sent through TCP to registered port 502. The default value is 502.
9 If you have selected a single (non-redundant)device type, you can skip this step.With cursor in Secondary
IP Address (SECIP) box, key in the IP address for the redundant device this block represents. This address
must be different than one used for the primary IP address (PRIMIP). (Only available when redundant
device type is selected.)
10 If you have selected a single (non-redundant) device type, you can skip this step.Click the <Tab> key to
move the cursor to the Secondary TCP Port (SECTCP) box. The default value is 502. (Only available
when redundant device type is selected.) An error message appears, if an invalid number, such as zero (0), is
entered. A zero value cannot be stored to the database.
11 If you have selected a single (non-redundant) device type, you can skip this step.Click the down-arrow
button in the Connection to use (CONTOUSE) box and select the desired connection to use. The default
selection is AUTO, so either the primary or secondary connection is automatically selected upon a device
failover.

Tip
In the Monitoring mode, you can use the CONTOUSE selection to force a specific connection. For example,
you can select Secondary and it will be the only connection used while the primary is disconnected and disabled
in this mode. This can be useful when performing maintenance on network or end-device equipment. An event
is issued to indicate that the alternate connection is disabled. No other channel or device failures are reported,
and active events at the time of the change become inactive.

12 The Connection in use (CONINUSE) box is read only and only applies for redundant devices.
13 If you have selected a single (non-redundant) device type, you can skip this step.Click the down-arrow
button in the Preferred connection to use (PREFERREDCONN) box and select the preferred connection
to use when the CONTOUSE parameter is set to Auto. The default selection is Primary.

34 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

14 If you have selected a single (non-redundant) device type, you can skip this step.With cursor in the
Connection Switch Period (sec) (REDSWITCHPERIOD) box, key in the desired switch time in seconds.
15 Check the Use Keep Alive check box to enable the option or clear the check box to disable the option. The
default selection is checked or enabled.

Tip
• If Device Type setting is Single or Redundant Safety Manager, all Slave Configuration parameters are set
automatically to the optimal settings.
• Users with Engineer access level or above can change the Slave Configuration parameter values, except for
UNITID and supported commands, in the Monitoring mode.

16 Click the Slave Configuration tab to display it.

With cursor in Timeout (ms) (DEFTIMOUT) box, key in desired MODBUS request timeout period in
milliseconds. The default is 1000 milliseconds for a native device or bridge, or 1500 milliseconds for a
Safety Manager.
This value is used for all serial devices unless overridden by a serial device. The DEFTIMOUT and
TIMOUT values must be greater than the configured slave timeout. This will ensure that a master block
timeout does not occur when a single serial device is unresponsive.
17 With cursor in Max Request Retries (REQRTRY) box, key in desired number of retries from 0 to 10. The
default is 1.
The number of retry counts the MODBUS device driver attempts after a failed read or write. Each failure is
recorded. A value of zero automatically reports a timeout with no retries. This value is used for all serial
devices, unless overridden by a serial device.
18 With cursor in Per Slave Requests (MAXUIDREQ), key in the desired maximum number of active
requests to a serial device from 1 to 64. The default is 1.
The maximum number of active requests to a serial device. An alarm is generated if a device exceeds the
active request per serial device.
19 With cursor in Max Transactions (MAXPENDREQ) box, key in the desired maximum number of
transactions for a PCDI_MASTER block between 1 to 64. The default is 1 or 2 for redundant device/Safety
Manager.
Once the maximum amount of transactions has been exceeded, an alarm is generated upon the next
transaction. Transactions that exceed the maximum number of transactions will be ignored.
20 With cursor in Message Delay (ms) (MSGDELAY) box, key in the desired delay period in milliseconds.
The default is 0.
(The Message Delay is the period between the last response received from the target device and the next
request sent to the device.)
21 With cursor in Rate (ms) (LOOPRATE) box, key in the desired period between testing each end device in
milliseconds. The default is 1000 milliseconds for native MODBUS TCP devices or 500 milliseconds for
Safety Manager.
22 Click the down arrow in the Type (LOOPTYPE) box and select desired function from the list. The default
is Diag Loopback or Diag Register for Safety Manager.

• If your LOOPTYPE selection is Coil, Discrete Input, Holding Reg, or Input Reg, go to Step 22.
• If your LOOPTYPE selection is Diag Loopback, go to Step 23.

35
5 PEER CONTROL DATA INTERFACE CONFIGURATION

• If your LOOPTYPE selection is Diag Register, go to Step 24.

• If your LOOPTYPE selection is Comm Event Log or Exception Status, go to Step 25.
23 The Address (LOOPADDR) box is read only in Monitoring mode.
(This box is only available if LOOPTYPE selection is Coil, Discrete Input, Holding Reg, or Input Reg.)
24 With cursor in Data (LOOPDATA) box, key in desired loop data value as TRUE, FALSE, ON, OFF, 0, or 1
for Coil or Discrete Input; or as integer or hexadecimal, with prefix '0x', format for Holding Reg or Input
Reg. The default is 0xA5A5.
(This box is only available if LOOPTYPE selection is Coil, Discrete Input, Holding Reg, Input Reg, or
Diag Loopback.)
25 Click the down arrow in the Data Change (LOOPDATACHG) box and select desired function from the
list. The default is No Change.

(This box is only available if LOOPTYPE selection is Coil, Discrete Input, Holding Reg, Input Reg, Diag
Loopback or .Diag Register.)
26 Click the down arrow in the Test Mode (LOOPMODE) box and select desired function from the list. The
default is Read Only.

• If the selected Device Type (DEVTYPE) is single or redundant MODBUS TCP Bridge, go to Step 28.
• If the Selected Device Type (DEVTYPE) is single or redundant MODBUS TCP Device, go to Step 29.
• If the selected Device Type (DEVTYPE) is single or redundant Safety Manager, go to Step 30.
27 The Slave Configuration tab for a MODBUS TCP Bridge device type includes the Serial Device
Definitions grid for configuring details about each serial device connected to the bridge.
• You must enter a valid Unit ID (1 to 247 or 255) to activate the fields in the grid for the assigned unit. A
Unit ID of zero (0) is valid to remove a device, but at least one device (non-zero) must be configured.

36 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

• Click the cursor in the appropriate grid field to make entries and activate down arrow buttons to make
selections, as applicable. A RED cell indicates that the Unit ID has no configured commands and is in
error.

Tip
Do not select commands that the device does not support. This prevents unsupported commands from being
issued and avoids lengthy timeouts from occurring that result in decreased performance and connection
reconnects. Safety Manager Commands are automatically configured.

28 Select a given device in the grid and click the Edit Commands button to call up the Configure Device
dialog and select the desired commands for the selected device.

37
5 PEER CONTROL DATA INTERFACE CONFIGURATION

• Be sure to enter desired configuration data for each device connected to the bridge.
• Go to Step 29.
29 Optional
You can enter values in the grid fields to override the default behavior of the values configured in Steps 15
to 26.
30 The Slave Configuration tab for Honeywell's Safety Manager or a MODBUS TCP device type includes the
Unit ID box and Command list box for configuring details about the device.

38 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

• With the cursor in Unit ID (UNITID) box, key in the device index number between 1 to 247 or 255 for
the device the block represents. The default is 255 for native device or 1 for Safety Manager.
• Select the desired commands for the device in the Command list box. Use the Select ALL or De-Select
All buttons, as applicable. See the next section “Device supported commands” on page 41 for more
information.
31 Click the Module Statistics tab to display it.
• Check the Alarming Enabled (ALMENBSTATE) check box to have alarm conditions displayed in the
Alarm Summary and Journals. Clear the check box to disable the display of alarm conditions. The
default is checked.
• The other parameters on this form are read only, except for RSTSTATS button, in the Monitoring mode
and are not configurable in Project. Error codes are displayed to assist users in tracing the cause of an
error.
32 Click the Connections Statistics tab to display it.
The parameters on this form are read only, except for the RSTERRCNT button, in the Monitoring mode and
are not configurable in Project.
33 Click the Channel Status tab to display it.
The parameters on this form are read only, except for the CHANRSTSTATS button, in the Monitoring
mode and are not configurable in Project.
34 Click the QVCS tab to display it.
The parameters on this form are mostly read only and provide information about the Qualification and
Version Control System pertinent to the device. See the Control Building Guide and/or the online help for
more information.
35 Click the Server History tab to display it.
Use this tab to configure desired history parameters and create or edit server scripts. See the Control
Building Guide and/or the online help for more information.
36 Click the Server Displays tab to display it.
Use this tab to configure parameters associated with Station displays. See the Control Building Guide and/or
the online help for more information.
37 Click the Control Confirmation tab to display it.
Use this tab to configure parameters for control confirmation associated with the licensed Electronic
Signature option. See the Control Building Guide and/or the online help for more information.
38 Click the Identification tab to display it.
Use this tab to configure parameters associated with the licensed template option. See the Control Building
Guide and/or the online help for more information.

39
5 PEER CONTROL DATA INTERFACE CONFIGURATION

39 When you completed entering configuration data, click the OK button to close the configuration form and
save the data.
40 This completes the procedure. Go to the next section.

40 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.3 Device supported commands

The following table lists the supported commands by function code along with a description and PCDI block
usage as well as default settings for Safety Manager.

Table 1: Device Supported Commands

Function Code Description Used by PCDI Blocks Safety Manager

Default
0x01 Read Coils PCDI_MASTER - Diag, On
PCDIFLAGARRCH
0x02 Read Discrete Inputs PCDI_MASTER - Diag, On
PCDIFLAGARRCH
0x03 Read Holding Registers PCDI_MASTER - Diag, On
PCDITEXTARRCH, PCDINUMARRCH
0x04 Read Input Registers PCDI_MASTER - Diag, On
PCDITEXTARRCH, PCDINUMARRCH
0x05 Write Single Coil PCDI_MASTER - Diag, On
PCDIFLAGARRCH
0x06 Write Single Register PCDI_MASTER - Diag, On
PCDITEXTARRCH, PCDINUMARRCH
0x07 Read Exception Status PCDI_MASTER - Diag Off
0x08 / 0x00 Diagnostic - Return Query Data PCDI_MASTER - Diag, On
PCDITEXTARRCH - loopback
0x08 / 0x01 Diagnostic - Restart Communications Off
0x08 / 0x02 Diagnostic - Return Diagnostic Register PCDI_MASTER - Diag On
0x08 / 0x03 Diagnostic - Change ASCII Delimiter Off
0x08 / 0x04 Diagnostic - Force Listen Only Off
0x08 / 0x0A Diagnostic - Clear Counters and Off
Diagnostic Register
0x08 / 0x0B Diagnostic - Return Bus Message Count Off
0x08 / 0x0C Diagnostic - Return Bus Communication Off
Error Count
0x08 / 0x0D Diagnostic - Return Bus Exception Error Off
Count
0x08 / 0x0E Diagnostic - Return Slave Message Off
Count
0x08 / 0x0F Return Slave No Response Count Off
0x08 / 0x10 Return Slave NAK Count Off
0x08 / 0x11 Return Slave Busy Count Off
0x08 / 0x12 Return Bus Character Overrun Count Off
0x08 / 0x13 Return IOP Message Overrun Count Off
0x08 / 0x14 Get / Clear MODBUS Plus stats Off
0x0B Get Communication Event Counter Off
0x0C Get Communication Event Log PCDI_MASTER - Diag Off
0x0F Write Multiple Coils PCDIFLAGARRCH On
0x10 Write Multiple Registers PCDITEXTARRCH, PCDINUMARRCH On

41
5 PEER CONTROL DATA INTERFACE CONFIGURATION

Function Code Description Used by PCDI Blocks Safety Manager

Default
0x11 Report Slave ID Off
0x14 / 0x06 Read File Record Off
0x15 / 0x06 Write File Record Off
0x16 Mask Write Register Off
0x17 Read / Write Multiple Registers Off
0x18 Read FIFO Queue Off
0x2B / 0x0E Read Device Information PCDI_MASTER - Honeywell Info On

42 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.4 Assigning PCDI_Master Block to Execution Environment

You can also just drag and drop the PCDI_MASTER block to the desired CEEC300 folder in the Project tree
instead of using the Execution Environment Assignment dialog, as outlined in the following procedure.
All illustrations used in the following procedure are for example purposes only.

Prerequisites
• You have started Configuration Studio and launched the Control Builder application.
• You have logged on with sufficient privileges to create control strategies using Control Builder.
• You have created a C300 Controller block in the Project tab.
• You have added a PCDI_MASTER block to the Project tab.

To assign PCDI_MASTER block to CEE

1 On the Edit menu, click Execution Environment Assignment; or click the Execution Environment
Assignment button on the toolbar to call up the Execution Environment Assignment dialog, as shown
in the sample illustration below.

2 If the IOMs tab is not on display in the Available modules list box, click the tab to display it.
Click the PCDI_MASTER block to be assigned to select it.
3 In the Assign To list box, click the CEE block that the PCDI_MASTER block is to be assigned to select it.
4 Click the Assign -> button to assign the selected module to the given CEE block.
5 Check that the PCDI_MASTER block now appears in the Assigned Modules list box for the given CEE
block, as shown in the sample illustration below.
Note that the equal symbol

43
5 PEER CONTROL DATA INTERFACE CONFIGURATION

prefix means that the block has been assigned and the down arrow symbol prefix means that the block
has been loaded to the Controller.

6 Click the Close button to exit the dialog and save the assignments.
7 This completes the procedure. Go to the next section.

44 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.5 Adding PCDI Array Request Channel Block to Control Module

The following procedure adds a PCDI Numeric Array Request Channel (PCDINUMARRCH) block to a CM
and assigns a channel to a PCDI_MASTER block for example purposes only. You can easily adapt this
procedure to apply to a PCDI Flag Array Request Channel (PCDIFLAGARRCH) block or a PCDI Text Array
Request Channel (PCDITEXTARRCH) block.
Each PCDI Array Request Channel block is automatically assigned a default tag name when it is created, which
must only be unique within the containing Control Module. If your system will include multiple Array Channel
blocks, you may want to adopt a more structured syntax for naming them.
The request block channel name can be up to 15 characters long and must contain at least on letter (A-Z). It
must not contain an embedded space or leading space, and dots are allowed in parameter naming only.
PCDI Numeric Array Channel (PCDINUMARRCH) function block's floating-point values may display
rounding errors if the decimal (non-real) numbers are used for scaling/substitution. For example, if a PVEUHI
value is 9.9 and PV is 4.0, then after scaling the PV value changes to 3.99. Similarly, if the PVEUHI is 10 and
PV is 3.99, then after scaling the PV value changes to 4.0.
You should use either the WriteAlwaysWriteOnly or WriteOnChgWriteOnly Write Option (WRITEOPT)
selection when configuring communications for a Safety Manager device. This avoids the possibility of wrong
values being sent back as a result of a read carried out directly after a write.
If the Safety Manager is configured to stop/freeze if a communication error occurs, then write requests are not
allowed to the Safety Manager until it has been reset. In addition, writes to the Safety Manager are not allowed,
even after the Safety Manager is reset, if the WRITEOPT is configured as WriteOnChg and the Safety Manager
device is running with faults. In this scenario, there is no indication of the writes to the Safety Manager failing
because the write requests are in a queue. Because of this, the PCDI reports a 'Safety Manager Running With
Faults diagnostic' alarm. A write to Safety Manager occurs when the WRITEOPT changes to WriteOnChg in
the Monitoring view. Writes to Safety Manager can also occur when the WRITEOPT is set to one of the
following write options.
• WriteAlwaysWriteOnly
• WriteOnChgWriteOnly
• WriteOnDiff
• WriteAlways
The Array Request Channel blocks are designed to read or write array data. Array data are accessible on a single
exposed pin as whole array data, or on individual pins specified by array index, which is configurable through
the Block Pins tab on the Array Request Channel block configuration form. A sample block pin configuration is
shown in the following illustration.

45
5 PEER CONTROL DATA INTERFACE CONFIGURATION

Users are responsible for verifying that the correct MODBUS addresses are maintained between request and
device blocks. There is no design time validation to verify the following:
• That the PCDI_MASTER Block device identifiers are synchronized with the Array Request Channel block
device identifiers.
• That valid addresses are provided for devices.
For PCDI_MASTER block to appear in the drop-down list on the Array Channel block's configuration form, the
Control Module containing the Array Channel block must be assigned to the same CEE as the PCDI_MASTER
block or both be unassigned in Project.
All illustrations used in the following procedure are for example purposes only.

Prerequisites
• You have started Configuration Studio and launched the Control Builder application.
• You have logged on with sufficient privileges to create control strategies using Control Builder.
• You have added a PCDI_MASTER block to the Project tab and assigned it to a C300 Control Execution
Environment.
• You have created a Control Module in the Project tab and assigned it to the same C300 Control Execution
Environment as the PCDI_MASTER block.

To add MODBUS TCP array request channel block to CM

1 In the Project tab, double-click the icon for the Control Module that is to include an array request channel
block to open it in the Control Drawing pane, as shown in the following sample illustration.

46 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

2 In the Library tab, scroll to the PCDI icon and click the plus sign to expand the tree.
You can also select the tag name in the following ways.
• Select Library mode and type the initial characters of a tag name.
• Using the Search Option toolbar
• Type the initial few characters of a tag name in the Search Option toolbar. A list of all matching tag
names appears.
• Select the tag name and click .
If the tag exists, the tree expands and the specified tag name is highlighted.
For more information on searching the tags, see Control Building User's Guide.
3 Click and drag the icon for the PCDINUMARRCH block to the open CM in the Control Drawing to add the
block to the CM, as shown in the following sample illustration.

47
5 PEER CONTROL DATA INTERFACE CONFIGURATION

4 Double-click the PCDINUMARRCHA block to open its configuration parameters form.

48 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5 Accept the highlighted default Channel Name or key in a new one.

6 Double-click the Execution Order in CM box and key in the desired number in multiples of 10 to define
the execution order of the block in the CM.
7 Click the down arrow in the Master Block Name box and select the PCDI_MASTER block to be associated
with this channel.

Once the PCDI_MASTER is selected, the Channel Number field is automatically updated, as shown in the
following sample illustration.

49
5 PEER CONTROL DATA INTERFACE CONFIGURATION

8 In the Channel Number list box, click the desired channel number this array request channel block is to be
assigned to. Channel 0 or the lowest available channel number is the default selection.
9 Click the Assign Request Block button to assign this channel to the selected channel number. The
Requestor Name field, the Assigned to Master and Assigned to Channel fields are automatically updated,
as shown in the following sample illustration.

10 Click the Configuration tab to display it.

50 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

11 Click the down arrow in the Access Lock (ACCLOCK) box and select who can change the block's value or
state based on sign on privileges. The default is Operator. Press the Tab key to move the cursor to the
Module Device Address box.

12 Check the Auto Trigger Mode (AUTOTRIGGER) check box to enable it. Clear the check box to disable
it. The default is checked so the block operates in the auto-triggered mode rather than the triggered mode.
Press the Tab key to move the cursor to the Auto Trigger Period (ms) (AUTOTRIGGERPERIOD) box
13 Key in the time in milliseconds to delay the beginning of the following auto-triggered block execution. The
default value is 0 milliseconds, which results in the block being triggered as quickly as possible. Press the
Tab key to move the cursor to the Device Address (DEVADDR) box.
(Auto triggered execution will resume in the Control Module cycle following expiration of the auto trigger
period. If the auto trigger period has expired before the DONEFL parameter transitions to true, the block
will be auto triggered immediately.)
14 Key in the address that identifies the MODBUS device connected to this request channel. The default is 1.
Press the Tab key to move the cursor to the Starting Element Index (STARTINDEX) box.
15 Key in the value to identify the start of the contiguous array in the MODBUS device. See the following
Starting Element Index Values section for more information about configuring the start index value. The
default varies for the given request channel type:
• PCDIFLAGARRCH = 1
• PCDINUMARRCH = 20001
• PCDITEXTARRCH = 500001

51
5 PEER CONTROL DATA INTERFACE CONFIGURATION

16 For PCDINUMARRCH block only:

Check the LONG (CONVTOLONG) check box to represent numeric values as longs. The default is
unchecked so numeric values are represented as floating point values.
(Checking the Long check box, provides support for 32-bit signed or unsigned integers depending on the
start index specified. The Long check box has no impact on floating point numerics, which are always 32-bit.
See the Startindex range 900001 - 965535 in Start index ranges define MODBUS function table for more
information. )
17 For PCDIFLAGARRCH block only:
With cursor in Number of Flag Values (NFLAG) box, key in the number of Boolean values in the array of
data from the device. The default is 1.
18 For PCDITEXTARRCH block only:
Check the ASCII Conversion (CONVTOASCII) box to use ASCII characters. Clear the check box to use
Unicode characters. The default is checked to use ASCII characters.
19 For PCDINUMARRCH block only:
With cursor in the Number of Numeric Values (NNUMERIC) box, key in the number that represents the
number of numeric values in the array of data from the device. The default is 1.
20 For PCDITEXTARRCH block only:
With cursor in Number of String Values (NSTRING) box, key in the number that represents the number of
string values in the array of data from the device. The default is 1.
21 For PCDITEXTARRCH block only:
With cursor in Char Length of String Values (STRLEN) box, key in the number of characters per string
value. The default is 8.
22 Click the down arrow in the Write Option (WRITEOPT) box and select how the Array Request Channel
block will handle writes to its 'data' parameter. The default is WriteOnDiff.

23 Click the Scaling/Substitution tab to display the dialog. (This tab is titled just Substitution for
PCDIFLAGARRCH and PCDITEXTARRCH blocks.)
24 Click the down arrow in the Default Substitution Type (SUBVALTYPE) box and select the value to
substitute when an error occurs. The default is Last known good.

(The NaN selection is only available for PCDINUMARRCH blocks.)

25 For PCDINUMARRCH and PCDITEXTARRCH blocks only:
With cursor in Default Substitution Value (SUBVAL) box, key in desired value to substitute when an error
occurs and the SUBVALTYPE setting is SUBVAL Param.
26 For PCDIFLAGARRCH block only: Check the Set to ON on error (SUBVAL) check box to turn the flag
ON when an error occurs. Leave the check box blank to disable the function. The default is unchecked or
disabled.
27 For PCDINUMARRCH block only: Key in applicable range information in the appropriate fields in the
Scaling/Substitution grid.

52 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

(Leaving all values at zero will perform raw writes/reads of PV data. Input values will be limited by the
range of the data type selected by the start index entered. Entering PVEUHI and PVEULO values only will
limit the input values by data type and PVEUHI/PVEULO values. Entering both PVEUHI/LO and
PVRAWHI/LO values will both limit the input and translate the input into the specified PVRAW range. If
PVRAWHI/LO values are specified, the PVRAW value written will be limited to the specified range. PV
output values are always reported as read with unlimited scaling applied. Note that no alarms are generated
when values go over/under limits, since there is no alarming associated with the concept of MODBUS
scaling.)
a Click and move the scroll bar at the bottom of the grid to the right side to expose the Substitution Type
(ELEMSUBVALTYPE) and Substitution Value (ELEMSUBVAL) fields.

b Click in the desired row of the Substitution Type (ELEMSUBVALTYPE) column and select the
desired type from the list. This setting will override the SUBVALTYPE setting unless it is set to Use
Default. The default is Use Default, which means the SUBVALTYPE setting is used.
c Click the desired row of the Substitution Value (ELEMSUBVAL) column and key in the desired value
to be used when ELEMSUBVALTYPE is SUBVAL Param.
28 For PCDIFLAGARRCH block only: Key in applicable information in the appropriate fields in the
Substitution Overrides grid.

a Click in the desired row of the Substitution Type (ELEMSUBVALTYPE) column and select the
desired type from the list. This setting will override the SUBVALTYPE setting unless it is set to Use
Default. The default is Use Default, which means the SUBVALTYPE setting is used.
b Click the desired row of the Substitution Value (ELEMSUBVAL) column and check the check box to
use ON or leave it unchecked for OFF as the value to use when ELEMSUBVALTYPE is SUBVAL
Param.
29 For PCDITEXTARRCH block only:Key in applicable information in the appropriate fields in the
Substitution Overrides grid.

a Click in the desired row of the Substitution Type (ELEMSUBVALTYPE) column and select the
desired type from the list. This setting will override the SUBVALTYPE setting unless it is set to Use
Default. The default is Use Default, which means the SUBVALTYPE setting is used.
b Click the desired row of the Substitution Value (ELEMSUBVAL) column and key in the desired value
to be used when ELEMSUBVALTYPE is SUBVAL Param.
30 Click the Status/Data tab to display the dialog.

53
5 PEER CONTROL DATA INTERFACE CONFIGURATION

There are no parameters on this tab to configure in Project. Use this tab to monitor selected data in the
Monitoring mode. The PCDI_MASTER block and Control Module must be loaded and active to make data
available on this tab.
31 Click the Identification tab to display the dialog.
Use this tab to configure parameters associated with the licensed template option. See the Control Building
Guide and/or the online help for more information.
32 Click the Block Pins tab to display the dialog.
Use this tab to configure the pins you want to expose for this block. See the Control Building Guide and/or
the online help for more information.
33 Click the Configuration Parameters tab to display the dialog.
Use this tab to configure the parameters to be displayed on the block in the Project mode. See the Control
Building Guide and/or the online help for more information.
34 Click the Monitoring Parameters tab to display the dialog.
Use this tab to configure the parameters to be displayed on the block in the Monitoring mode. See the
Control Building Guide and/or the online help for more information.
35 Click the Block Preferences tab to display the dialog.
Use this tab to configure the viewing preferences for the block. See the Control Building Guide and/or the
online help for more information.
36 If you have a template license, click the Template Defining tab to display the dialog.
Use this tab to select which parameters are to be template defining. See the Control Building Guide and/or
the online help for more information.
37 When you completed entering configuration data, click the OK button to close the configuration form and
save the data.
38 This completes the procedure. Go to the next section.

54 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.6 Starting Element Index Values

You specify the Starting Element Index (STARTINDEX) parameter through the Configuration tab on the
configuration form for the given PCDI Array Request Channel block in Control Builder, as noted in the
previous procedure. This parameter defines the MODBUS address map.
The value configured for the STARTINDEX parameter in a given Array Request Channel block determines the
MODBUS Start Index and function. Only one type of external data can be accessed per Array Channel block.
The STARTINDEX parameter specifies the MODBUS data type and a MODBUS address up to 65535. The
most significant digit identifies the MODBUS function. For example, read coil status as noted in the following
table. The lower five digits define the starting address to access data for the given MODBUS function. For
example, the address ranges 2xxxxx, 4xxxxx, 5xxxxx, 7xxxxx, 8xxxxx, and 9xxxxx all address the same xxxxx
holding registers in the MODBUS end device, but with different data formats. When multiple numeric data
types are used, you must configure the STARTINDEX for each array to avoid overlapping arrays.
The following table shows the relationship between MODBUS functions, the STARTINDEX parameter range,
and number of elements. The maximum number of elements specifies the maximum number of flags, numerics,
or strings that can be configured for a given STARTINDEX range and Array Request Channel block type. All of
the specified elements are read in a single transaction.

Table 2: Start index ranges define MODBUS function

STARTINDEX MODBUS Function Read FC Array Request Channel Block Data Range Max.
Ranges
Write FC No.
Elem.
000001 - 065535 Read Coil Status 01 PCDIFLAGARRCH ON/OFF 1968
Write Single Coil 05 Read/Write Bit Flags
Write Multiple Coils 15
100001 - 165535 Read Input Status 02 PCDIFLAGARRCH ON/OFF 1968
Not Applicable N/A Read Only Bit Flags
200001 - 265535 Read Holding Registers 03 PCDINUMARRCH -34E38 to 34E38 60
Write Single Register 06 Word Swapped IEEE FI.Pt
Write Multiple 16 Read/Write
Registers
300001 - 365535 Read Input Registers 04 PCDINUMARRCH -32768 to 32767 120
Not Applicable N/A Signed Integer Words -2147483648 to 60
2147483647
Read only
400001 - 465535 Read Holding Registers 03 PCDINUMARRCH -32768 to 32767 120
Signed Integer Word/Long See
Array
Note 1
Read/Write
Write Single Register 06 -2147483648 to 60
2147483647
Write Multiple 16
Registers
500001 - 565535 Read Holding Registers 03 PCDITEXTARRCH Printable See
Characters
Write Single Register 06 ASCII Encoded Bytes or Note 2
UNICODE (2 Byte)
Write Multiple 16
Characters
Registers
Read/Write

55
5 PEER CONTROL DATA INTERFACE CONFIGURATION

STARTINDEX MODBUS Function Read FC Array Request Channel Block Data Range Max.
Ranges
Write FC No.
Elem.
600000 Loopback Diagnostics 08 PCDITEXTARRCH Printable See
Characters
Loopback Test Note 2
600001 -665535 Read/Write Honeywell 03/06/16 Honeywell Information 80 chars.
Information Transfer to Master Block
699999 Write Honeywell 06/16
Information
700001 - 765535 Read Holding Registers 03 PCDINUMARRCH -34E38 to 34E38 60
Write Single Registers 06 IEEE Floating Point
Write Multiple 16 Read/Write
Registers
800002 - 865535 Read Holding Registers 03 PCDINUMARRCH -34E38 to 34E38 60
Write Single Registers 06 IEEE FI. Pt
Write Multiple 16 Read/Write
Registers
900001 - 965535 Read Holding Registers 03 PCDINUMARRCH 0 to 65535 120
Write Single Register 06 Unsigned Integer Words / 0 to 4294967295 603
Longs
Write Multiple Register 16
Read/Write
1. Configuring Modbus Holding Register address with the Read/Write Option (WRITEOPT) parameter set to
“ReadOnly” forces the PCDI to use the corresponding input register address and Modbus function code 0x04 (Read
Input Registers).
2. NSTRING = 120 / STRLEN, if CONVTOASCII is not checked; or NSTRING = 240 / STRLEN, if
CONVTOASCII is checked.
3. 60, if CONVTOLONG is selected; 120 if not.

56 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.7 MODBUS loopback diagnostics and Text Array Request Channel

block configuration
The Text Array Request Channel block supports up to 240 bytes. If the CONVERTTOASCII parameter is
enabled, it can be configured as 240 ASCII characters. If not enabled, it can be configured as 120 Unicode
(wide-2 byte) characters.
You can divide the 240 bytes into as many as 16 strings by configuring the number of string (NSTRING) and
string length (STRLEN) parameter values accordingly. The data transferred is always the entire string. All
strings are SPACE character padded. There is no NULL padding
The 500001 - 565535 range implements the standard write/read Text Array Request Channel block
functionality. All strings read into the STR[1..NSTRING] values will be space padded to the STRLEN
parameter value.
Address 600000 implements a diagnostic loopback function. In this mode, data written to the block follows the
same rules as for the Text Array Request Channel block, but the MODBUS function code used is for diagnostic
- return query data (08-00). Returned data in the loopback response is saved to the output STR process value.
There is no read request sent for address 600000.
Since the MODBUS function can only handle a single word (2 bytes) at a time, the number of writes required to
complete the cycle will be depend on whether CONVERTTOASCII is enabled or not, the NSTRING value, and
the STRLEN value.
For Addresses in the 600001 - 665535 range, values will be transferred to both the STR process value and will
be written to the associated PCDI_MASTER block VENDOR string. The VENDOR string is 80 characters and
will truncate excessively long strings. If multiple strings are configured (NSTRING > 1), the strings read will be
concatenated with a SPACE character separating them. Only printable characters will be transferred to the
VENDOR string.
Address 699999 provides a means of transferring input data on the STR[1..NSTRING] input pins into the
PCDI_MASTER block VENDOR string. The same rules apply for the transfer of data as for the previous
address range.

57
5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.8 Whole array support

A whole array transfer allows you to connect together two arrayed parameters in Control Builder with the same
data type. Once the configuration is loaded and running, the connection is formed between the two parameters
and the entire array is requested and transferred to the destination block as one parameter access request. The
array is available as a named parameter for connection to peer controllers by connecting to the parameter name.

Array write scenario

With whole array transfer, the write data can be brought in as an array from another block that supports whole
array transfer. A whole array write can occur, if the write method is set to WriteAlways. With the other methods,
the data write will be one element at a time.
The WriteAlways function will write all values transferred into the block. The WriteOnDiff and WriteOnChg
functions will optimize use of single and multiple write commands to minimize the number of Control Module
(CM) cycles required to transfer only those values that are different/changed. Use of single or multiple write
commands is restricted by the commands selected in the Supported Commands dialog through the
PCDI_MASTER block configuration form.

58 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.9 Simulation support

When you assign a PCDI_MASTER block and CM containing associated PCDI Array Request Channel blocks
to the CEESIMC300FB, the blocks support the SIM-C300 simulation environment such that their input values
can be read and written to by an operator or other applications. You can run the simulation of Array Request
Channel blocks with or without a PCDI_MASTER block. For simulations without a PCDI_MASTER block, the
alarms are not supported.
In the simulation environment, the communication between PCDI_MASTER block and MODBUS TCP
hardware is blocked. You generate alarms manually by setting connection status, ERRFL, device status, and so
on. The channel state for PCDI Array Request Channel blocks is put in simulate and is displayed on the channel
block faceplate in Station and on the Channel Status tab of PCDI_MASTER block configuration form in the
Monitoring tab of Control Builder.
You can configure the simulation mode as DirectSub, SimValueSub, or None. When mode is DirectSub, an
operator or other application can write directly to the PV, ignoring the connection. When mode is
SimValueSub, the SIMVALUE is substituted for the PV. The SIMVALUE can be fetched from another block
using a parameter connection or it can be set by an operator or the other applications. In both modes, Error Flag
and Error Code can be written by an operator or the other applications. When mode is None, the PV is fetched
from connected blocks, or from applications or users with proper access level.

59
5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.10 Loading configuration data to the CEE

The following procedure is based on doing an initial load of a block from the Project tab. You can also initiate a
re-load of a block from the Monitoring tab.
You can load the CEE and its assigned contents such as I/O modules and Control Modules at the same time. See
the Control Building User's Guide for more information about the load operation.
The PCDI Array Request Channel blocks are loaded with their containing Control Module.
All the illustrations used in the procedure are for example purposes only.

CAUTION The load operation is still an offline function. The Load Dialog box provides the ability to
automatically inactivate a component during a load and then return the component to its active state.
Do not use this automatic inactivate/activate function, if your process cannot tolerate the load
disruption and consequent delay in activation. In this case, you must manually toggle the component
state through the Monitoring tab in Control Builder.

Prerequisites
• You have started Configuration Studio and launched the Control Builder application.
• You have logged on with sufficient privileges to create control strategies using Control Builder.
• You have loaded the Controller and its execution environment.
• You have assigned the PCDI_MASTER block to the loaded Execution Environment

To load PCDI_MASTER block

1 In the Project tab, click the plus signs to expand the tree hierarchy for the C300 Controller, CEEC300, and
I/O icons, as required.
You can also select the tag name in the following ways.
• Select Library mode and type the initial characters of a tag name.
• Using the Search Option toolbar
a Type the initial few characters of a tag name in the Search Option toolbar. A list of all matching tag
names appears.
Select the tag name and click
If the tag exists, the tree expands and the specified tag name is highlighted.
For more information on searching the tags, see Control Building User's Guide.
2 Right-click the PCDI_MASTER block icon and select Load from the menu to call up the Load dialog.

60 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

• Be sure the check box in the Load column is checked.

• Click the down arrow in the Post Load State column to select another state.
• Check the check box at the bottom of the dialog to automatically change the state of the PCDI_MASTER
to the selected Post Load State after the load is completed.
3 Click the OK button to initiate the load and track progress through the Load Monitor dialog.
4 After load completes, check that the PCDI_MASTER icon now appears in the Monitoring tab tree
hierarchy.
5 This completes the procedure. Go to the next section.

61
5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.11 PCDI_MASTER Block properties form reference

For more details about a given parameter listed in one of the following sections, please refer to the Control
Builder Parameter Reference.

Related topics
“Main tab parameters” on page 62
“Module Configuration tab parameters” on page 63
“Slave Configuration tab parameters” on page 64
“Module Statistics tab parameters” on page 65
“Connection Statistics tab parameters” on page 66
“Channel Status tab parameters” on page 67
“Server History tab parameters” on page 67
“Server Displays tab parameters” on page 68
“Control Confirmation tab parameters” on page 69
“Identification tab parameters” on page 70

5.11.1 Main tab parameters

The following table summarizes the parameter data you can monitor and/or configure on the Main tab of the
configuration form for the selected PCDI_MASTER block. Remember to check the Show Parameter Names
check box, if you want to display the parameter names instead of the plain text on the form.

Plain Text Parameter Name User Notes

Configurable
Module Name NAME Project Only System
assigned or user
configured
unique name.
Consisting of
up to 16
characters and
at least one
character must
be a letter (A-
Z).
Item Name Item Name Project Only A non-unique
name by which
an entity is
known within
the context of
the enterprise
model.
Device Type DEVTYPE Project Only Select the type
of end device
the block
represents.

62 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Notes

Configurable
Module Description DESC Project Only User defined
text that
appears on
Detail and
Group displays
for the block.
Currently Assigned Channels N/A Yes ( through Read only list
array request box shows all
blocks) Array Request
Channel
assignments to
the block

5.11.2 Module Configuration tab parameters

The following table summarizes the parameter data you can monitor and/or configure on the Module
Configuration tab of the configuration form for the selected PCDI_MASTER block. Remember to check the
Show Parameter Names check box, if you want to display the parameter names instead of the plain text on the
form.

Plain Text Parameter Name User Configurable Notes

Primary IP Address PRIMIP Project Only IP address for Primary or non-
redundant Modbus device that block
represents
Primary TCP Port PRIMTCP Project Only All MODBUS application data units
are sent through TCP to registered
port 502.
Secondary IP Address SECIP Project Only IP address for Secondary Modbus
device. Only available for redundant
Device Types.
Secondary TCP Port SECTCP Project Only All MODBUS application data units
are sent through TCP to registered
port 502.
Connection to use CONTOUSE Project and Select connection to use with
redundant devices. Can be used to
Monitoring (for
force a specific connection. Only
Engineer and above)
available for redundant Device Types.
Connection in use CONINUSE No Shows current connection is use with
redundant devices. Only available for
redundant Device Types.
Preferred connection to use PREFERREDCONN Project and Define the connection to use when the
Connection to use value is Auto.
Monitoring (for
Requests that use of specific
Operator and above)
connection be attempted. Only
available for redundant Device Types.
Connection Switch Period REDSWITCHPERIOD Project and Define redundant switch period is
(sec) seconds. Only available for redundant
Monitoring (for
Device Types.
Engineer and above)
Use Keep Alive USEKEEPALIVE Project Only Enable or disable the Modbus
KEEPALIVE option.

63
5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.11.3 Slave Configuration tab parameters

The following table summarizes the parameter data you can monitor and/or configure on the Slave
Configuration tab of the configuration form for the selected PCDI_MASTER block. Users must have an access
level of Engineer or above to configure values in the Monitoring mode. Remember to check the Show
Parameter Names check box, if you want to display the parameter names instead of the plain text on the form.

Plain Text Parameter Name User Configurable Notes

Timeout (ms) DEFTIMOUT Project and Set Modbus request timeout period in
Monitoring (for milliseconds.
Engineer or above)
Maximum Request Retries REQRTRY Project and Set number of retry counts Modbus
Monitoring (for device driver attempts after a failed
Engineer or above) read or write.
Per Slave Requests MAXUIDREQ Project and Set maximum number of active
Monitoring (for requests to a serial device.
Engineer or above)
Max Transactions MAXPENDREQ Project and Set maximum number of transactions
Monitoring (for for PCDI_MASTER device block.
Engineer or above)
Message Delay (ms) MSGDELAY Project and Set message delay time in
Monitoring (for milliseconds.
Engineer or above)
Rate (ms) LOOPRATE Project and Set time between testing each end
Monitoring (for device in milliseconds.
Engineer or above)
Address LOADADDR Project and Specify loop address.
Monitoring (for
Engineer or above)
Data LOOPDATA Project and Represents the data value written to
Monitoring (for diagnostic request to slave devices
Engineer or above) LOOPADDR.
Type LOOPTYPE Project and Set loop type operation
Monitoring (for
Engineer or above)
Test Mode LOOPMODE Project and Lets you set the desired test mode to
Monitoring (for use when a diagnostic request is
Engineer or above) issued. See parameter definition for
details.
Data Change LOOPDATACHG Project and The data value written to a diagnostic
Monitoring (for request to slave devices.
Engineer or above)
Unit ID UNITID[0..15] Project Only Device Index: Only available for
native Modbus device.
Command N/A Project Only List of selectable commands for
native Modbus device.
Serial Device Definitions N/A Project and List of Modbus RTU devices
Monitoring (for associated with Modbus Bridge: Only
Engineer or above) available with Device Type Modbus
Bridge.

64 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.11.4 Module Statistics tab parameters

The following table summarizes the parameter data you can mostly monitor only on the Module Statistics tab
of the configuration form for the selected PCDI_MASTER block. Remember to check the Show Parameter
Names check box, if you want to display the parameter names instead of the plain text on the form.

Plain Text Parameter Name User Configurable Notes

Alarm Enable ALMENBSTATE Yes Enable or disable alarm propagation
to alarm displays.
Module State IOMSTATE Read Only Defines the current execution state of
the associated peer device module.
In-Alarm Flag INALM Read Only
Requests Sent TOTALREQSENT Read Only
Responses Rcvd REQRSPRCVD Read Only
Orphaned Responses ORPHANRESPCNT Read Only Number of responses received for
which there was no longer an
outstanding request. Request may
have timed-out, or has been cancelled.
Max Msgs Rcvd/sec MAXRCVMSGPERSE Read Only
C
Max Bytes Rcvd/sec MAXRCVBYTESPERS Read Only
EC
Max Msgs Sent/sec MAXXMITMSGPERSE Read Only
C
Max Bytes Sent/sec MAXXMITBYTESPER Read Only
SEC
Avg Msgs Rcvd/sec AVGRCVMSGPERSEC Read Only
Avg Bytes Rcvd/sec AVGRCVBYTESPERS Read Only
EC
Avg Msgs Sent/sec AVGXMITMSGPERSE Read Only
C
Avg Bytes Sent/sec AVGXMITBYTESPERS Read Only
EC
Unit Index UNITIDMON[0..15] Read Only Unit index (MODBUS address) for
each end device.
Device Status DEVSTS[0..15] Read Only Device status as determined by
diagnostics.
Device Type UIDDEVTYPEMON[0.. Read Only Reads corresponding value of
15] UIDDEVTYPE[0-15]
Honeywell Info VENDOR[0..15] Read Only
Requests Sent UIDREQSENT[0..15] Read Only
Responses Received UIDREQRSPRCVD[0-1 Read Only
5]
Request Retries REQRTRYCNT[0-15] Read Only
Request Timeouts TIMOUTCNT[0-15] Read Only
Queued Requests QUEUEDREQCNT[0-1 Read Only
5]

65
5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

UID Orphaned Responses UIDORPHANRESPCN Read Only
T[0-15]
Diag Requests DIAGREQSENT[0-15] Read Only
Diag Responses DIAGREQRSPRCVD[0 Read Only
-15]
Expected Data UIDEXPECTDATA[0..1 Read Only
5]
Received Data UIDRCVDDATA[0..15] Read Only
Error Count MBERRCNT[0..15] Read Only
Error Flag MBERRFL[0..15 Read Only
Last Error LASTMBERR[0..15] Read Only
Last Error Time LASTMBERRTIME[0-1 Read Only
5]

5.11.5 Connection Statistics tab parameters

The following table summarizes the parameter data you can monitor only on the Connection Statistics tab of
the configuration form for the selected PCDI_MASTER block. Remember to check the Show Parameter
Names check box, if you want to display the parameter names instead of the plain text on the form.

Plain Text Parameter Name User Configurable Notes

Primary
IP Address PRIMIPMON Read Only
TCP Port PRIMTCPMON Read Only
Connection Status PRIMCONNSTS Read Only
Successful Connects PRIMNUMCONN Read Only
Conn Attempts PRIMNUMCONNATM Read Only
PT
Last connect time PRIMLASTCONNTIM Read Only
E
Disconnects PRIMNUMDISCONN[0
..15]
Last Disconnect Time PRIMLASTDISCONNT
IME[0..15]
Error Count PRIMERRCNT Read Only
Error Flag PRIMERRFL Read Only When Set, Error Flag parameter
indicates that Last Error is active.
Last Error PRIMERRCODE Read Only
Additional Error Info PRIMERRINFO Read Only
Last Error Time PRIMLASTERRTIME Read Only
Secondary
IP Address SECIPMON Read Only
TCP Port SECTCPMON Read Only
Connection Status SECCONNSTS Read Only
Successful Connects SECNUMCONN Read Only

66 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

Conn Attempts SECNUMCONNATMP Read Only
T
Last connect time SECLASTCONNTIME Read Only
Disconnects SECNUMDISCONN[0.. Read Only
15]
Last Disconnect Time SECLASTDISCONNTI Read Only
ME[0..15]
Error Count SECERRCNT Read Only
Error Flag SECERRFL Read Only When Set, Error Flag parameter
indicates that Last Error is active.
Last Error SECERRCODE Read Only
Additional Error Info SECERRINFO Read Only
Last Error Time SECLASTERRTIME Read Only

5.11.6 Channel Status tab parameters

The following table summarizes the parameter data you can monitor on the Channel Status tab of the
configuration form for the selected PCDI_MASTER block. Remember to check the Show Parameter Names
check box, if you want to display the parameter names instead of the plain text on the form.

Plain Text Parameter Name User Notes

Configurable
Assigned FB CHANFBNAME[0..63] Read Only
Ch Status CHANSTS[0..63] Read Only
Requests Sent CHANREQSENT[0..63] Read Only
Responses CHANREQRSPRCVD[ Read Only
0..63]
Cycle Time (ms) CYCLETIME[0..63] Read Only Reports total elapsed time of the last cycle of
operations in milliseconds for the request
block to complete the cycle. Includes all write
and read requests.
Last Error CHANLASTMBERR[0. Read Only
.63]
Err Time CHANLASTMBERRTI Read Only
ME[0..63]

5.11.7 Server History tab parameters

The Server History tab is common to all configuration forms for tagged blocks in Control Builder. The
following table summarizes the parameter data you can monitor and configure on this tab of the configuration
form for the selected PCDI_MASTER block.

Attention
The configuration settings you make for Server Load Options on the System Preferences dialog determines whether
or not the data entered on the Server History tab is loaded to the Experion Server. See the Control Building Guide for
information about setting system preferences.

67
5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

Access Levels
Control Level SCANCTRLLVL Yes Indicates Server control level to be
associated with this function.
History Configuration
Number of History HIST.NUMPARAMS Yes Defines number of history parameters
Parameters to be included in History
Configuration table.
Parameter HIST.PARAM Yes Valid parameter name for a parameter
associated with the given point that is
to be collected and stored as historical
data at predetermined intervals.
Description No Provides a brief description of the
entered parameter.
FAST HIST.FAST Yes Select the Fast type of history
collection.
STD HIST.STD Yes Select the Standard type of history
collection.
EXTD HIST.EXTD Yes Select the Extended type of history
collection.
EXC HIST.EXC Yes(Station only) Select the Exception type of history
collection.
Gating Parameter HIST.GATEPARAM Yes Optional gating parameter to define
conditions under which data for this
parameter should be collected.
Gate State HIST.GATEVALUE Yes Defines gate state for configured
gating parameter.
Create New or Edit Existing N/A Launch the Server scripting
Server Scripts (Button) configuration utility.

5.11.8 Server Displays tab parameters

The Server Displays tab is common to all configuration forms for tagged blocks in Control Builder. The
following table summarizes the parameter data you can monitor and configure on this tab of the configuration
form for the selected PCDI_MASTER block.

Attention
The configuration settings you make for Server Load Options on the System Preferences dialog determines whether
or not the data entered on the Server Displays tab is loaded to the Experion Server. See the Control Building Guide
for information about setting system preferences.

Plain Text Parameter Name User Configurable Notes

Point Detail Display SCANPNTDTL Yes By default, a Display template is
already entered into Point Detail
Display box (for example,
Sysdtlmbtcpdevicea). This template
can be used for creating your own
display or it can be used as is,
provided that your function block
name matches name built into detail
display that is supplied as a template.

68 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

Group Detail Display SCANGRPDTL Yes By default, a Display template is
already entered into the Group Detail
Display box (for example,
Sysdtlmbtcpdevicea_fp). This
template can be used for creating your
own display or it can be used as is,
provided that your function block
name matches name built into detail
display that is supplied as a template
Associated Display SCANASSOCDSP Yes Name of the Server display to be
associated with this function block.
Trends
Number of Trends TREND.NUMPARAMS Yes Defines the number of trend
parameters to be included in the
Trends Configuration table.
Trend # Yes Defines Trend number to be
associated with this trend parameter
Pen Yes Defines color of pen that will be used
to trace assigned parameter on Station
Trend display.
Trend Parameter Yes Valid parameter name for a parameter
associated with given point that is
configured for history collection.
Description No Provides a brief description of the
entered parameter.
Groups
Number of Groups GROUP.NUMPARAMS Yes Defines the number of group
parameters to be included in Groups
Configuration table.
Group # Yes Defines Group number to be
associated with this group parameter.
Pos # Yes Defines number of position
configured parameter will occupy in
the Station Group display.
Group Parameter Yes Valid parameter name for a parameter
associated with the given point that is
configured in the system.
Description No Provides a brief description of the
entered parameter.

5.11.9 Control Confirmation tab parameters

The Control Confirmation tab is common to all configuration forms for tagged blocks in Control Builder. If
you have an optional Electronic Signature license, you can configure electronic signature information for the
tagged block through this tab on the block's configuration form in Control Builder. Please refer to the online
help and the Server and Client Configuration Guide for information about the data on this tab.
The Electronic Signature function aligns with the identical Electronic Signatures function that is initiated
through Quick Builder and Station for Server points. When this block is loaded to a controller, its control
confirmation configuration (electronic signatures) is also loaded to the Server. This means you can view the
control confirmation configuration for this tagged object in Station and also make changes to it. If you make
changes through Station, you must initiate an Upload or Upload with Contents function through the

69
5 PEER CONTROL DATA INTERFACE CONFIGURATION

Controller menu in Control Builder for the object in the Monitoring tab to synchronize changes in the
Engineering Repository Database (ERDB).

5.11.10 Identification tab parameters

The Identification tab is common to all configuration forms for blocks in Control Builder. The following table
summarizes the parameter data you can monitor and configure on this tab of the configuration form for the
selected PCDI_MASTER block.

Plain Text Parameter Name User Configurable Notes

Name NAME Yes Unique block name consisting of up to
16 characters to identify the block. At
least one character in the name must
be a letter (A-Z).
Description DESC Yes Descriptive text appears on detail and
group displays to uniquely describe
this particular function block
Block Comment 1 BLCKCOMMENT1 Yes Comment to be associated with this
block consisting of up to 40
characters.
Block Comment 2 BLCKCOMMENT2 Yes Comment to be associated with this
block consisting of up to 40
characters.
Block Comment 3 BLCKCOMMENT3 Yes Comment to be associated with this
block consisting of up to 40
characters.
Block Comment 4 BLCKCOMMENT4 Yes Comment to be associated with this
block consisting of up to 40
characters.
Library No Identifies Control Builder Library that
is source of template.
System Template No Identifies System Template that is
source for this block.
Base Template No Identifies Base Template that is used
for this block.
Created By CREATEDBY No Identifies user who created block, if
operator security is implemented.
Otherwise, may just show Default
login.
Date Created DATECREATED No Shows date and time template was
created. If this block is in Version
Control System, shows date and time
initial version of template was created.
Last Modified By MODIFIEDBY No Identifies user who made last
modifications to block, if operator
security is implemented. Otherwise,
may just show default login. If this
block is in Version Control System,
modifications apply to last version of
block.

70 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

Date Last Modified VERSIONDATE No Shows date and time last modification
was made to block's configuration. If
this block is in Version Control
System, modification date and time
applies to last version of block.

71
5 PEER CONTROL DATA INTERFACE CONFIGURATION

5.12 Array Request Channel Block properties form reference

Related topics
“Main tab parameters” on page 72
“Configuration tab parameters” on page 72
“Scaling/Substitution tab parameters” on page 74
“Status/Data tab parameters” on page 75
“Identification tab parameters” on page 75
“Dependencies tab parameters” on page 76
“Block pins tab parameters” on page 76
“Configuration parameters tab parameters” on page 76
“Monitoring parameters tab parameters” on page 76
“Block preferences tab parameters” on page 76
“Template defining tab parameters” on page 76

5.12.1 Main tab parameters

The following table summarizes the parameter data you can monitor and/or configure on the Main tab of the
configuration form for the selected PCDIFLAGARRCH, PCDINUMARRCH, or PCDITEXTARRCH block.
Remember to check the Show Parameter Names check box, if you want to display the parameter names
instead of the plain text on the form.

Plain Text Parameter Name User Configurable Notes

Request Block Name NAME Project Only System assigned or user configured
unique name. Consisting of up to 15
characters and at least one character
must be a letter (A-Z).
Execution Order in CM ORDERINCM Project Only Determines the execution order of
function blocks within a Control
Module (CM)
Master Block Name N/A Project Only Select associated PCDI_MASTER
block.

5.12.2 Configuration tab parameters

The following table summarizes the parameter data you can monitor and/or configure on the Configuration tab
of the configuration form for the selected PCDIFLAGARRCH, PCDINUMARRCH, or PCDITEXTARRCH
block. Remember to check the Show Parameter Names check box, if you want to display the parameter names
instead of the plain text on the form.

Plain Text Parameter Name User Configurable Notes

Access Lock ACCLOCK Project Only Select access level for block.

72 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

Auto Trigger Mode AUTOTRIGGER Project Only Enable or disable the auto trigger
mode of request block execution.
In the triggered mode, the block
submits a request on the positive
transition of the input trigger flag. In
the auto triggered mode, the
DONEFL is internally looped back to
the trigger to provide for the fastest
update rate possible. In this mode, the
block will be capable of refreshing
data at the same rate as the execution
cycle of the containing CM, but
limited by the response time of the
addressed device.
Auto Trigger Period (ms) AUTOTRIGGERPERI Project Only Used to delay the beginning of the
OD following auto triggered block
execution. Auto triggered execution
will resume in the CM cycle
following expiration of the auto
trigger period. If the auto trigger
period has expired before the
DONEFL parameter transitions to
true, the block will be auto triggered
immediately. The default
AUTOTRIGGERPERIOD value is 0
milliseconds, which results in the
block being triggered as quickly as
possible.
Device Address DEVADDR Project Only Specify applicable MODBUS device
address.
Starting Element Index STARTINDEX Project Only Set applicable start index value for
given Array Request Channel block
Long CONVTOLONGI Project Only Applicable to PCDINUMARRCH
block only.
Enable or disable convert to long
function.
ASCII Conversion CONVTOASCII Project Only Applicable to PCDITEXTARRCH
block only.
Enable or disable convert text to
ASCII function.
Number of Flag Values NFLAG Project Only Applicable to PCDIFLAGARRCH
block only.
Define number of flags to read.
Range is 1 to 1968.
Number of Numeric Values NNUMERIC Project Only Applicable to PCDINUMARRCH
block only.
Define number of numeric values to
read. Valid values are actually
dependent upon the STARTINDEX.

73
5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

Number of String Values NSTRING Project Only Applicable to PCDITEXTARRCH
block only.
Define number of string values to
read.
The number of strings times the
number of characters per string may
not exceed 120 Unicode characters or
240 ASCII characters.
Char Length of String Values STRLEN Project Only Applicable to PCDITEXTARRCH
block only.
Define number of characters per
string
The number of strings times the
number of characters per string may
not exceed 120 Unicode characters or
240 ASCII characters.
Read/Write Option WRITEOPT Project Only Select read/write setting for block.

5.12.3 Scaling/Substitution tab parameters

The following table summarizes the parameter data you can monitor and/or configure on the Scaling/
Substitution or Substitution tab of the configuration form for the selected PCDINUMARRCH, or
PCDIFLAGARRCH or PCDITEXTARRCH block. Remember to check the Show Parameter Names check
box, if you want to display the parameter names instead of the plain text on the form.

Plain Text Parameter Name User Configurable Notes

Default Substitution Type SUBVALTYPE Project Only Select what value to substitute when
error occurs.
Default Substitution Value SUBVAL Project Only Applicable to PCDINUMARRCH
and PCDITEXTARRCH blocks only.
Set value to use when error occurs.
Set to ON on error SUBVAL Project Only Applicable to PCDIFLAGARRCH
block only.
Enable or disable set to ON on error
function.
PV High Range (in PVEUHI Project Only Applicable to PCDINUMARRCH
Engineering Units) block only.
Specify high range value in
Engineering Units.
PV Low Range (in PVEULO Project Only Applicable to PCDINUMARRCH
Engineering Units) block only.
Specify low range value in
Engineering Units.
PV Raw High Range PVRAWHI Project Only Applicable to PCDINUMARRCH
block only.
PV raw high range value.
PV Raw Low Range PVRAWLO Project Only Applicable to PCDINUMARRCH
block only.
PV raw low range value.

74 www.honeywell.com
 5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

Engineering Unit Description EUDESC Project Only Applicable to PCDINUMARRCH
block only.
Provide description of applicable
Engineering Unit.
Substitution Type ELEMSUBVALTYPE Project Only Substitution on error is supported
with common SUBVALTYPE and
SUBVAL parameters that may be
overridden with parameters
ELEMSUBVALTYPE and
ELEMSUBVAL on per element
basis.
Substitution Value ELEMSUBVAL Project Only See row above.

5.12.4 Status/Data tab parameters

The following table summarizes the parameter data you can monitor on the Status/Data tab of the configuration
form for the selected PCDIFLAGARRCH, PCDINUMARRCH, or PCDITEXTARRCH block. Remember to
check the Show Parameter Names check box, if you want to display the parameter names instead of the plain
text on the form.

Plain Text Parameter Name User Configurable Notes

Ch Status CHANSTS Monitoring Only See parameter definition for details.
Error Flag ERRFL Monitoring Only Enable or disable error flag function.
When set, indicates that ERRCODE is
currently active.
Last Error ERRCODE Monitoring Only See parameter definition for details.
Bad PV Flag BADPVFL Monitoring Only
Time of Last Error LASTERRTIME No
Process Value PVFL Monitoring Only Applicable to PCDIFLAGARRCH
block only.
Process Value PV Monitoring Only Applicable to PCDINUMARRCH
block only.
Process Value Raw PVRAW Monitoring Only Applicable to PCDINUMARRCH
block only.
Process Value STR[1..16 Monitoring Only Applicable to PCDITEXTARRCH
block only.

5.12.5 Identification tab parameters

The Identification tab is common to all configuration forms for basic blocks in Control Builder. The following
table summarizes the parameter data you can monitor and configure on this tab of the configuration form for the
selected Array Request Channel block.

Plain Text Parameter Name User Configurable Notes

Name NAME Yes Unique block name consisting of up
to 15 characters to identify the block.
At least one character in the name
must be a letter (A-Z).

75
5 PEER CONTROL DATA INTERFACE CONFIGURATION

Plain Text Parameter Name User Configurable Notes

Block Comment 1 BLCKCOMMENT1 Yes Comment to be associated with this
block consisting of up to 40
characters.
Block Comment 2 BLCKCOMMENT2 Yes Comment to be associated with this
block consisting of up to 40
characters.
Block Comment 3 BLCKCOMMENT3 Yes Comment to be associated with this
block consisting of up to 40
characters.
Block Comment 4 BLCKCOMMENT4 Yes Comment to be associated with this
block consisting of up to 40
characters.
Library No Identifies Control Builder Library that
is source of template.
System Template No Identifies System Template that is
source for this block.
Base Template No Identifies Base Template that is used
for this block.

5.12.6 Dependencies tab parameters

The Dependencies tab is common to all configuration forms for basic blocks in Control Builder. Please refer to
the online help and the Control Builder User's Guide for more information about the data on this tab.

5.12.7 Block pins tab parameters

The Block Pins tab is common to all configuration forms for basic blocks in Control Builder. Please refer to the
online help and the Control Builder User's Guide for more information about the data on this tab.

5.12.8 Configuration parameters tab parameters

The Configuration Parameters tab is common to all configuration forms for basic blocks in Control Builder.
Please refer to the online help and the Control Builder User's Guide for more information about the data on this
tab.

5.12.9 Monitoring parameters tab parameters

The Monitoring Parameters tab is common to all configuration forms for basic blocks in Control Builder.
Please refer to the online help and the Control Builder User's Guide for more information about the data on this
tab.

5.12.10 Block preferences tab parameters

The Block Preferences tab is common to all configuration forms for basic blocks in Control Builder. Please
refer to the online help and the Control Builder User's Guide for more information about the data on this tab.

5.12.11 Template defining tab parameters

The Template Defining tab is common to all configuration forms for basic blocks in Control Builder. Please
refer to the online help and the Control Builder User's Guide for more information about the data on this tab.

76 www.honeywell.com
6 Peer Control Data Interface operation

Related topics
“Monitoring Peer Control Data Interface functions through Station displays” on page 78
“Monitoring PCDI Functions through the Monitoring tab in Control Builder” on page 86
“Initiating Switchover of Redundant Devices” on page 92
“Checking license details” on page 93
“Response to C300 RAM retention restart” on page 94
“PCDI support for checkpoint save/restore functions” on page 95

77
6 PEER CONTROL DATA INTERFACE OPERATION

6.1 Monitoring Peer Control Data Interface functions through Station

displays
The Experion Server Station application includes pre-configured Detail displays for the PCDI_MASTER
function blocks. These displays are the default entries for the Point Detail Page parameter on the Server
Displays tab of the configuration form. Once you establish communications with a peer device, you can begin
monitoring the status of any component that has been loaded as part of a Control Strategy to an Experion
Controller with points registered in the Experion Server. The Detail displays let you quickly view the
component's current state, fault status, and pertinent configuration data.
Please refer to the Operator's Guide for detailed information about calling up, navigating, and viewing displays
in Station.

6.1.1 Graphical example of PCDI_MASTER block detail display

The following illustration shows the faceplate for a PCDI master device displaying its component state. See the
following tables for description of illustration callouts and peer device text messages.
Figure 3: Sample PCDI Master Device Detail Display

Table 3: Description of Figure 5 Callouts.

Callout Description
1 Module name configured through Control Builder.
2 Module description configured through Control Builder.

78 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

Callout Description
3 Peer device text indicating current general status of functions.
4 LEDs show current connection status.
5 Shows any alarm condition. Click button to acknowledge alarm.
6 Identifies the connection in use.
7 Identifies the preferred connection to use.
8 Shows the current execution status of the device.

Table 4: Table Peer Device Text Description

If text is . . . Then, for a single or pair of redundant Safety Managers, Modbus TCP
Bridges, or Modbus TCP devices it means . . .
Inactive PCDI_MASTER Block is Inactive
Initializing Connection(s) in transition
Cnx Fail Connection(s) failed.
Cnx Offline No Connections available. (That is: CONTOUSE = NONE.)
If text is . . . Then, for a single or pair of redundant Modbus TCP Bridges, or Modbus
TCP devices it means . . .
Cnx OK DV Init Connection(s) OK, all peer devices/Modbus RTU devices in transition
Cnx OK DV OK Connection(s) OK and all peer devices/Modbus RTU devices OK.
Cnx OK DV PF Connection(s) OK and at least one peer device/Modbus RTU device failed (That
is: peer devices/Modbus RTU devices partially failed).
Cnx OK DV POK Connection(s) OK, at least one peer device/Modbus RTU device OK and no peer
devices/Modbus RTU devices failed (That is: peer devices/Modbus RTU devices
partially OK).
Cnx OK DV Fail Connection(s) OK and all peer devices/Modbus RTU devices failed.
If text is . . . Then, for a pair of redundant Modbus TCP Bridges or Modbus TCP devices,
it means . . .
Cnx Marg DV Init One connection failed and the alternate connection is in use, all peer devices/
Modbus RTU devices in transition
Cnx Marg DV OK One connection failed and the alternate connection is in use, all peer devices/
Modbus RTU devices OK.
Cnx Marg DV PF One connection failed and the alternate connection is in use and at least one peer
device/Modbus RTU device failed (That is: peer devices/Modbus RTU devices
partially failed).
Cnx Marg DV POK One connection failed and the alternate connection is in use and at least one peer
device/Modbus RTU device OK and no peer devices/Modbus RTU devices failed
(That is: peer devices/Modbus RTU devices partially OK).
Cnx Marg DV Fail One connection failed and the alternate connection is in use and all peer devices/
Modbus RTU devices failed.
If text is . . . Then, for a single or pair of redundant Safety Managers, it means . . .
Cnx OK SM Init Connection(s) OK, all Safety Manager devices in transition
Cnx OK SM OK Connection(s) OK and all Safety Manager devices OK.
Cnx OK SM PF Connection(s) OK and at least one Safety Manager device failed (That is: Safety
Manager devices partially failed).
Cnx OK SM POK Connection(s) OK, at least one Safety Manager device OK and no Safety Manager
devices idle or failed (That is: Safety Manager devices partially OK).
Cnx OK SM Fail Connection(s) OK and all Safety Manager devices failed.

79
6 PEER CONTROL DATA INTERFACE OPERATION

Cnx OK SM Idle Connection(s) OK, at least one Safety Manager device idle and no Safety Manager
device failed.
If text is . . . Then, for a pair of redundant Safety Managers, it means . . .
Cnx Marg SM Init One connection failed and the alternate connection is in use, all Safety Manager
devices in transition
Cnx Marg SM OK One connection failed and the alternate connection is in use, all Safety Manager
devices OK.
Cnx Marg SM PF One connection failed and the alternate connection is in use and at least one Safety
Manager device failed (That is: Safety Manager devices partially failed).
Cnx Marg SM POK One connection failed and the alternate connection is in use and at least one Safety
Manager device OK and no Safety Manager devices idle or failed (That is: Safety
Manager devices partially OK).
Cnx Marg SM Fail One connection failed and the alternate connection is in use and all Safety
Manager devices failed.
Cnx Marg SM Idle One connection failed and the alternate connection is in use, at least one Safety
Manager device idle and no Safety Manager device failed.

6.1.2 Graphical example of viewing Last Error on Channel Status tab of PCDI_MASTER block in
Station
Figure 4: Example View of Last Error on Channel Status Tab in Station

1 Click the Config Details tab on Detail Display.

2 Click scroll bar for tab and move to right side.

80 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

3 Click the Channel Status tab.

4 Click the scroll bar on the tab and move to the right side to expose the Last Error column.

6.1.3 Graphical example of PCDI_MASTER block in system component tree

The following illustration shows a PCDI master device being displayed on the system component tree in
Station. See the following table for list and description of possible status icon conditions.
Figure 5: Typical System Component Tree View

Table 5: Table Status Icon Description

If Status Icon is . . . Then, It Means

Connection(s) OK, all peer devices/Modbus RTU devices OK

Connection(s) marginal or peer devices/Modbus RTU devices marginal

Connection(s) failed or any peer devices/Modbus RTU devices failed

Master Block is Inactive

81
6 PEER CONTROL DATA INTERFACE OPERATION

6.1.4 Using Station System Status display

Like the Detail displays, the System Status Display supports the integration of PCDI Master Device block
generated notifications and events. It is integrated with Experion component data and is for the most part self-
explanatory. PCDI channel blocks will report channel alarms through the Device Block they are assigned to.
Channel alarms will be returned to normal if alarm condition no longer exists, the channel block state is
changed to inactive, or the channel block is deleted. Use this display to get a quick review of recent actions that
have been initiated within the system.

6.1.5 Graphical example of PCDI_MASTER block in Alarm pane of System Status Display
The following illustration shows alarm events for PCDI master device. See the following table for list and
description of possible Peer Control Data Interface event subtypes in the Experion Notification System based on
a per PCDI Master Device block basis.
Figure 6: System Status Display Alarm Pane

82 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

Table 6: Peer Control Data Interface Event Subtypes

Peer Control Data Interface Cond Prty Auxiliary Descriptor Event Description
Event Subtype
Connection Fail DIAG H Connection(s) FAIL For a single Modbus device, an alarm
is generated when a single Modbus
device connection has failed.
For a redundant pair of Modbus
devices, an alarm is generated when
both connections of a redundant pair of
Modbus devices have failed.
Connection Warning DIAG H Connection Warning For a redundant pair of Modbus
devices, an alarm is generated when a
single connection has failed and the
alternate connection is in use.
Single Device FAIL DIAG H Single Device FAIL For a single MODBUS TCP Device,
an alarm is generated when the single
connection is OK, but the single
MODBUS TCP Device has failed.
Primary Device FAIL DIAG H Primary Device FAIL For a redundant MODBUS TCP
Device, an alarm is generated when the
primary connection is OK, but the
primary MODBUS TCP Device has
failed.
Secondary Device FAIL DIAG H Secondary Device FAIL For a redundant MODBUS TCP
Device, an alarm is generated when the
secondary connection is OK, but the
secondary MODBUS TCP Device has
failed.
Primary Connection is forced DIAG H Secondary Offline For a redundant pair of Modbus
devices, an alarm is generated when
CONTOUSE is set to Primary.
Secondary Connection is DIAG H Primary Offline For a redundant pair of Modbus
forced in use devices, an alarm is generated when
CONTOUSE is set to Secondary.
Primary and secondary DIAG H No Connections Available For a single Modbus device or a
connections are forced offline redundant pair of Modbus devices, an
alarm is generated when CONTOUSE
is set to NONE.
Primary All UID FAIL DIAG H Primary All UID FAIL For a single MODBUS TCP Bridge, an
alarm is generated when all Modbus
RTU devices on the primary
connection have failed.
For a redundant MODBUS TCP
Bridge, an alarm is generated when all
Modbus RTU devices on primary
connection have failed, CONINUSE is
switched to Secondary, the alarm will
not return to normal until CONINUSE
is switched back to Primary again and
alarm condition has been cleared.

83
6 PEER CONTROL DATA INTERFACE OPERATION

Peer Control Data Interface Cond Prty Auxiliary Descriptor Event Description
Event Subtype
Secondary All UID FAIL DIAG H Secondary All UID FAIL For a redundant MODBUS TCP
Bridge, an alarm is generated when all
Modbus RTU devices on secondary
connection have failed, CONINUSE is
switched to Primary, the alarm will not
return to normal until CONINUSE is
switched back to Secondary again and
alarm condition has been cleared.
Single Safety Manager FAIL DIAG H Single SM FAIL For a single Safety Manager, an alarm
is generated when the single
connection is OK, but the single Safety
Manager has failed.
Primary Safety Manager FAIL DIAG H Primary SM FAIL For a redundant Safety Manager, an
alarm is generated when the primary
connection is OK, but the primary
Safety Manager has failed.
Secondary Safety Manager DIAG H Secondary SM FAIL For a redundant Safety Manager, an
FAIL alarm is generated when the secondary
connection is OK, but the secondary
Safety Manager has failed.
Single Safety Manager IDLE DIAG H Single SM IDLE For a single Safety Manager, an alarm
is generated when the single Safety
Manager is IDLE.
Primary Safety Manager IDLE DIAG H Primary SM IDLE For a redundant Safety Manager, an
alarm is generated when the primary
Safety Manager is IDLE.
Secondary Safety Manager DIAG H Secondary SM IDLE For a redundant Safety Manager, an
IDLE alarm is generated when the secondary
Safety Manager is IDLE.
Serial Device [0..15] Fail DIAG H UID xxx FAIL For a single MODBUS TCP Bridge or
a redundant MODBUS TCP Bridge
with up to 16 Modbus RTU devices, an
alarm is generated when a Modbus
RTU device has failed.
(xxx is Modbus TCP Bridge Modbus
RTU device Unit ID, range 1..247 and
255)
Serial Device [0..15] Disabled DIAG H UID xxx Disabled For a single MODBUS TCP Bridge or
a redundant MODBUS TCP Bridge
with up to 16 Modbus RTU devices, an
alarm is generated when a Modbus
RTU device has been disabled.
(xxx is Modbus TCP Bridge Modbus
RTU device Unit ID, range 1..247 and
255)
Channel Fail [0..63] DIAG H Channel xxFAIL For a single Modbus device or a
redundant pair of Modbus devices, an
alarm is generated when an assigned
channel has failed.
(xx is assigned channel number, range
0..63).

84 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

Legend:
• single Modbus device = single MODBUS TCP Bridge, single MODBUS TCP Device or Safety Manager
• redundant pair of Modbus devices = redundant MODBUS TCP Bridge, redundant MODBUS TCP Device,
or redundant Safety Manager
Refer to the Operator's Guide for more information about using the Station interface.

85
6 PEER CONTROL DATA INTERFACE OPERATION

6.2 Monitoring PCDI Functions through the Monitoring tab in Control

Builder

Related topics
“Activating/inactivating PCDI_MASTER device” on page 86
“PCDI_MASTER device block icon appearances” on page 86
“Control Module block icon appearances” on page 89
“Monitoring/Interacting with given component/block” on page 89
“Monitoring PCDI related statistics through C300 block in Monitoring mode” on page 90
“Monitoring PCDI related statistics through CEEC300 block in Monitoring mode” on page 90

6.2.1 Activating/inactivating PCDI_MASTER device

Use the following procedure to change the state of a PCDI_MASTER device through the Monitoring tab in
Control Builder.
Activating a PCDI_MASTER device generates a state event change and resumes the module's normal periodic
processing.
Inactivating a PCDI_MASTER device generates a state event change; blocks channel access to flag, numeric,
and string data from the device; and sets channel depending on SUBVALTYPE, as well as setting associated
BADPVFL.

Prerequisites
• You have logged on with sufficient privileges to make changes in a control strategy.
• You have loaded a control strategy to the Controller and can view the PCDI_MASTER device through the
Monitoring tab of Control Builder.

To activate or inactivate a PCDI_MASTER device

1 Right-click the PCDI_MASTER device icon (green) and click Inactivate>Selected Item(s) on the menu.
Or,
Right click the PCDI_MASTER device icon (blue) and click the Activate>Selected Item(s) on the menu.
2 Click the Yes button to confirm the action in the Change State dialog.
3 Wait for PCDI_MASTER device icon to turn blue/inactive.
Or,
Wait for PCDI_MASTER device icon to turn green/active.
4 This completes the procedure. Go to the next section.

6.2.2 PCDI_MASTER device block icon appearances

The following table summarizes the various appearances that a PCDI_MASTER device block icon in Control
Builder can assume based on configuration, view, and current PCDI_MASTER device operating state and
status.

86 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

If Icon is . . . Then, it represents . . . And, Module

State (IOMSTATE)*
Is. . .
Project Tab
(gray) PCDI_MASTER non-redundant bridge configured for N/A
operation in Project.
(gray) PCDI_MASTER non-redundant MODBUS TCP device N/A
configured for operation in Project.
(gray) PCDI_MASTER non-redundant Safety Manager configured N/A
for operation in Project.
(gray) PCDI_MASTER redundant bridges configured for operation N/A
in Project.
(gray) PCDI_MASTER redundant MODBUS TCP devices N/A
configured for operation in Project.
(gray) PCDI_MASTER redundant Safety Managers configured for N/A
operation in Project.
Monitoring Tab
(gray) PCDI_MASTER non-redundant bridge is loaded, but not N/A
monitoring
(blue) PCDI_MASTER non-redundant MODBUS TCP device is N/A
loaded, but not monitoring
(green) PCDI_MASTER non-redundant Safety Manager is loaded, but N/A
not monitoring
(gray) PCDI_MASTER redundant bridges are loaded, but not N/A
monitoring
(gray) PCDI_MASTER redundant MODBUS TCP devices are N/A
loaded, but not monitoring
(gray) PCDI_MASTER redundant Safety Managers are loaded, but N/A
not monitoring
(blue) PCDI_MASTER non-redundant bridge is inactive INACTIVE

(blue) PCDI_MASTER non-redundant MODBUS TCP device is INACTIVE

inactive
(blue) PCDI_MASTER non-redundant Safety Manager is inactive INACTIVE

(blue) PCDI_MASTER redundant bridges are inactive INACTIVE/INACTIVE

(blue) PCDI_MASTER redundant MODBUS TCP devices are INACTIVE/INACTIVE

inactive
(blue) PCDI_MASTER redundant Safety Managers are inactive INACTIVE/INACTIVE

(green) PCDI_MASTER non-redundant bridge is active OK

(green) PCDI_MASTER non-redundant MODBUS TCP device is OK

active
(green) PCDI_MASTER non-redundant Safety Manager is active OK

(green) PCDI_MASTER redundant bridges are active OK/OK

(green) PCDI_MASTER redundant MODBUS TCP devices are active OK/OK

(green) PCDI_MASTER redundant Safety Managers are active OK/OK

(yellow) PCDI_MASTER non-redundant bridge is not used STBY

87
6 PEER CONTROL DATA INTERFACE OPERATION

If Icon is . . . Then, it represents . . . And, Module

State (IOMSTATE)*
Is. . .
(yellow) PCDI_MASTER non-redundant MODBUS TCP device is not STBY
used.
(yellow) PCDI_MASTER non-redundant Safety Manager is not used STBY

(yellow/yellow) PCDI_MASTER redundant bridges are not used STBY/STBY

(yellow/yellow) PCDI_MASTER redundant MODBUS TCP devices are not STBY/STBY

used
(yellow/yellow) PCDI_MASTER redundant Safety Managers are not used STBY/STBY

(green/yellow) PCDI_MASTER primary redundant bridge is active, OK/STBY

secondary bridge is not used
(green/yellow) PCDI_MASTER primary redundant MODBUS TCP device is OK/STBY
active, secondary device is not used
(green/yellow) PCDI_MASTER primary redundant Safety Manager is active, OK/STBY
secondary Safety Manager is not used
(yellow/green) PCDI_MASTER primary redundant bridge is not used, STBY/OK
secondary bridge is active
(yellow/green) PCDI_MASTER primary redundant MODBUS TCP device is STBY/OK
not used, secondary device is active
(green/yellow) PCDI_MASTER primary redundant Safety Manager is not STBY/OK
used, secondary Safety Manager is active
(green/red/red PCDI_MASTER primary redundant bridge is active, OK/FAIL
exclamation) secondary bridge has failed

(green/red/red PCDI_MASTER primary redundant MODBUS TCP device is OK/FAIL

exclamation) active, secondary device has failed

(green/red/red PCDI_MASTER primary redundant Safety Manager is active, OK/FAIL

exclamation) secondary Safety Manager has failed

(yellow/red/red PCDI_MASTER primary redundant bridge is not used, STBY/FAIL

exclamation) secondary bridge has failed

(yellow/red/red PCDI_MASTER primary redundant MODBUS TCP device is STBY/FAIL

exclamation) not used, secondary device has failed

(yellow/red/red PCDI_MASTER primary redundant Safety Manager is not STBY/FAIL

exclamation) used, secondary Safety Manager has failed

(red/green/red PCDI_MASTER primary redundant bridge has failed, FAIL/OK

exclamation) secondary bridge is active

(red/green/red PCDI_MASTER primary redundant MODBUS TCP device FAIL/OK

exclamation) has failed, secondary device is active

(red/green/red PCDI_MASTER primary redundant Safety Manager has FAIL/OK

exclamation) failed, secondary Safety Manager is active

(red/yellow/red PCDI_MASTER primary redundant bridge has failed, FAIL/STBY

exclamation) secondary bridge is not used

(red/yellow/red PCDI_MASTER primary redundant MODBUS TCP device FAIL/STBY

exclamation) has failed, secondary device is not used

(red/yellow/red PCDI_MASTER primary redundant Safety Manager has FAIL/STBY

exclamation) failed, secondary Safety Manager is not used

88 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

If Icon is . . . Then, it represents . . . And, Module

State (IOMSTATE)*
Is. . .
(red/red/red PCDI_MASTER primary redundant bridge has failed, FAIL
exclamation) secondary bridge has failed

(red/red/red PCDI_MASTER primary redundant MODBUS TCP device FAIL

exclamation) has failed, secondary device has failed

(red/red/red PCDI_MASTER primary redundant Safety Manager has FAIL

exclamation) failed, secondary Safety Manager has failed

(red/black exclamation) PCDI_MASTER non-redundant bridge with communication FAIL

failure
(red/black exclamation) PCDI_MASTER non-redundant MODBUS TCP device with FAIL
communication failure
(red/black exclamation) PCDI_MASTER non-redundant Safety Manager with FAIL
communication failure
(red/red exclamation) PCDI_MASTER non-redundant bridge has failed FAIL

(red/red exclamation) PCDI_MASTER non-redundant MODBUS TCP device has FAIL

failed
(red/red exclamation) PCDI_MASTER non-redundant Safety Manager has failed FAIL
* This parameter appears on the Module Statistics tab of the Module Properties form for the selected PCDI_MASTER
block in Monitoring mode.

6.2.3 Control Module block icon appearances

The following table summarizes the various appearances that a CM block icon in Control Builder can assume
based on configuration, view, and current CM operating state and status.

If Icon is . . . Then, it represents . . . And, Execution State* Is. . .

Project Tab
(gray) CM configured for operation in Project. N/A
Monitoring Tab
(gray) CM loaded, but not monitoring N/A

(blue) CM inactive INACTIVE

(green) CM Active ACTIVE

(red/black exclamation) CM with communication failure N/A

* This appears in title bar on Module Properties form for selected Control Module in Monitoring mode.

6.2.4 Monitoring/Interacting with given component/block

Once you download a Controller and its contents, you can use the Monitoring tab to interact with the
components including the function blocks in the Control Module.
You simply double-click the desired component/block icon in the hierarchy tree menus under the Controller
icon to call up the associated Configuration form or open the Control Module in the Control Drawing to double-
click blocks contained in the CM. Click the given Configuration form tab to view the current status of the
related block data. Both the PCDI_MASTER and CM function blocks must be active to view online data. The

89
6 PEER CONTROL DATA INTERFACE OPERATION

data can be viewed either by name or parameter reference by not checking or checking the Show Parameter
Names check box at the bottom of each tab.
Please refer to the Control Building Guide sections in On-Line Monitoring Using Control Builder for detailed
information:
• Setting the CEE Inactive
• Changing Parameters while Monitoring

6.2.5 Monitoring PCDI related statistics through C300 block in Monitoring mode
Use the following steps to monitor performance counters for PCDI functions on the C300 block configuration
form.
1 Double click the C300 block icon on the Monitoring tab to call up its configuration form.
2 Click the Statistics tab to display the tab.

3 Monitor the data in the MBTCP Network Message Statistics section for PCDI related functions performance.
4 Click the OK button to close the form.

6.2.6 Monitoring PCDI related statistics through CEEC300 block in Monitoring mode
Use the following steps to monitor performance counters for PCDI functions on the CEEC300 block
configuration form.
1 With C300 block tree hierarchy expanded, double click the CEEC300 block icon on the Monitoring tab to
call up its configuration form.
2 Click the Statistics tab to display the tab and use the scroll bar to scroll to the bottom of the tab.

90 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

3 Monitor the data in the MBTCP Transmit Statistics and MBTCP Receive Statistics sections for PCDI related
functions performance.
4 Click the OK button to close the form.

91
6 PEER CONTROL DATA INTERFACE OPERATION

6.3 Initiating Switchover of Redundant Devices

You can manually initiate a switchover of redundant peer devices through the Monitoring tab in Control
Builder.
A peer device fail over occurs when the maximum number of requests for the device have been attempted. This
can be caused when the device time out occurs on each of the retries or if the device returns a failure after each
retry
If you have Engineer security level or above, you can change the Connection to Use (CONTOUSE) parameter
configuration in Monitoring mode to force the connection in use and disable the connection not selected. All
connection attempts and alarms will be disabled on the non-selected connection. This function may be useful for
maintenance purposes.

Prerequisites
• You have logged on with sufficient privileges to make changes in a control strategy.
• You have loaded a control strategy to the Controller and can view the PCDI_MASTER device through the
Monitoring tab of Control Builder.

To initiate manual switchover

1 Double-click the PCDI_MASTER device icon (green) to call up its configuration properties form.
2 Click the Module Configuration tab to display it.
3 Click the down-arrow in the Preferred Connection to use box and select Secondary from the list. Confirm
the action.
4 A switch-over is attempted. If an error occurs, the connection switches back to the best connection available.
The Connection in Use box displays the resulting connection.
5 This completes the procedure. Go to the next section.

92 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

6.4 Checking license details

Please refer to the Control Hardware Planning Guide for more information about viewing application licenses
and features.

93
6 PEER CONTROL DATA INTERFACE OPERATION

6.5 Response to C300 RAM retention restart

During a C300 RAM retention restart (RRR), all block request states are scanned and any non-pending or
completed requests are set to error condition to force retransmission in the first block execution cycle. Request
state will be available in battery backed PCI RAM. If the pending requests are not received (missed) due to
excessive restart time or because they were sent while the node was unavailable, the requests are retransmitted
and if they have reached the maximum retry count, they will timeout.

94 www.honeywell.com
 6 PEER CONTROL DATA INTERFACE OPERATION

6.6 PCDI support for checkpoint save/restore functions

The Checkpoint function in Control Builder lets you save and restore operation and configuration data
associated with a controller. The primary purpose of Checkpoint's save and restore functions are to provide the
operator with the capability to bring a failed controller back to an operational condition as soon as possible.
There are other ancillary scheduling, archiving and rebuilding functions provided by Checkpoint. Refer to the
Checkpoint Reference section the Control Building User's Guide for more information about the checkpoint
function.
While the operation and configuration data associated with PCDI supports the standard Experion checkpoint
save/restore functions, note the following exceptions for the given PCDI parameter data.
• A checkpoint save operation will not save any run-time values for the following PCDI related parameters. It
will only save the configuration values for these parameters.

PCDI Parameter PCDI Parameter PCDI Parameter

DEFTIMOUT LOOPTYPE UIDLOOPMODE
MAXPENDREQ LOOPADDR UIDLOOPTYPE
MAXUIDREQ LOOPDATA UIDLOOPADDR
REQRTRY LOOPDATACHG UIDLOOPDATA
MSGDELAY PREFERREDCONN UIDLOOPDATACHG
LOOPRATE TIMOUT
LOOPMODE UIDLOOPRATE

• A checkpoint save operation does not save a parameter that is not exposed during configuration even if a
run-time configuration change exposes the parameter. For example, when LOOPTYPE is configured as
Diag Register, both LOOPADDR and LOOPDATA are not available/exposed. If the LOOPTYPE
configuration is changed to Coil during run-time, both LOOPADDR and LOOPDATA are available/exposed;
but they will not be saved in the checkpoint file.

95
6 PEER CONTROL DATA INTERFACE OPERATION

96 www.honeywell.com
7 Peer Control Data Interface maintenance

Related topics
“Periodic checks” on page 98

97
7 PEER CONTROL DATA INTERFACE MAINTENANCE

7.1 Periodic checks

The following table identifies checks that you should make periodically (every 3 to 6 months) to keep the peer
control data interface in good working condition.

Check . . . Possible Corrective Action . . .

That all connections are secure. Secure connections, as needed.
That cable insulation is not worn or cracked. Replace cables, as required.
That third-party equipment is being maintained. Follow vendor maintenance recommendations.

98 www.honeywell.com
8 Peer Control Data Interface troubleshooting

Related topics
“Isolating problems” on page 100
“Fault classifications” on page 101
“Initial checks” on page 102
“Fixing common problems” on page 104
“Getting further assistance” on page 105

99
8 PEER CONTROL DATA INTERFACE TROUBLESHOOTING

8.1 Isolating problems

This section offers some general data about fault classifications and initial checks that may help you isolate the
cause of a problem.
If you have observed a specific symptom and/or identified an error code, go to the Fixing Common Problems
section to see if you can find a matching topic.

100 www.honeywell.com
 8 PEER CONTROL DATA INTERFACE TROUBLESHOOTING

8.2 Fault classifications

The following table lists some possible ways for classifying faults along with some identifying characteristics.

Fault Classification Characteristics

Hard Failure Failure detected by hardware; operation cannot continue. If the fault does not prevent
software processing the problem, the affected node will be rebooted under software
control into the FAIL State.
• If failure occurs on Primary node, it triggers a switchover to synchronized
Secondary node.
• If failure occurs on Secondary node, it results in loss of synchronization and
reduced availability until the problem is resolved.
• If failure occurs on non-redundant node, it results in loss of control and loss of
view.
Severe Failure Failure detected by software; operation cannot continue. The affected node will be
rebooted under software control into the FAIL State.
The failure scenarios are as listed in the row above for the Hard Failure.
Soft Failure Failure detected by software; operation continues with full control and full view. Soft
failures are alarmed to the operator. FTE will be monitored by the FTE System
Management Tool.
• If failure occurs on Primary node, it does not trigger a switchover to
synchronized Secondary node.
• If failure occurs on Secondary node, it does not result in loss of synchronization.
• If failure occurs on non-redundant node, it does not result in loss of control and
loss of view.
Installation/Startup Failure Detected by software. Node may not become operational.
• This failure does not apply to synchronized Primary node, since installation and
startup must be successful to reach synchronized Primary state.
• If failure occurs on Secondary node, it results in the inability to complete the
initial synchronization and to view the node on the network.
• If failure occurs on non-redundant node, it results in the inability to commence
control and to view the node on the network.

101
8 PEER CONTROL DATA INTERFACE TROUBLESHOOTING

8.3 Initial checks

This section offers some checks that you can make to help isolate the problem. The checks are arranged in no
particular order.

Related topics
“Checking Control Builder error code reference” on page 102
“Viewing release information log” on page 102
“Viewing trace log” on page 102
“Checking version and revision log” on page 102
“Checking server point build log” on page 103
“Checking server point build error log” on page 103
“Checking error log” on page 103

8.3.1 Checking Control Builder error code reference

An indication of a problem may be in the form of an error dialog that includes an error message and possibly an
error code in Control Builder.
The syntax for a typical Control Builder error message is as shown in the following illustration:

In this syntax, the error code is the last five digits in the message or 10689.
Please refer to the Control Builder Error Codes Reference book for applicable error code information.

8.3.2 Viewing release information log

The ReleaseInfo.txt log provides a list of Experion software releases that have been installed on the computer.
To view the log, navigate to this file location on the server: C:\Program Files\Honeywell\Experion PKS
\Engineering Tools\system\bin\ReleaseInfo.txt.

8.3.3 Viewing trace log

The TraceLogRs.txt log provides a list of definitions for strings associated with breadcrumbs data for given
hardware components. The breadcrumbs provide a way to trace operations leading up to an event.
To view the log, navigate to this file location on the server: C:\Program Files\Honeywell\Experion PKS
\Engineering Tools\system\bin\TraceLogRs.txt.

8.3.4 Checking version and revision log

The ver_rev.txt log provides a list of components by model number with software version/revision along with
compatible Experion software release(s).

102 www.honeywell.com
 8 PEER CONTROL DATA INTERFACE TROUBLESHOOTING

To check the log, navigate to this file location on the server: C:\Program Files\Honeywell\Experion PKS
\Engineering Tools\system\bin\ver_rev.txt.

8.3.5 Checking server point build log

The SvrPtBld.txt log provides list of process (CB) points built in the server database.
To check the log, navigate to this file location on the server: C:\Program Files\Honeywell\Experion PKS
\Engineering Tools\temp\SvrPtBld.txt.

8.3.6 Checking server point build error log

The svrptblderr.txt log provides list of any errors associated with process (CB) points built in the server
database
To check the log, navigate to this file location on the server: C:\Program Files\Honeywell\Experion PKS
\Engineering Tools\temp\svrptblderr.txt.

8.3.7 Checking error log

The Errlog_n.txt log provides a running list of Control Builder detected errors in chronological order. The n
represents any number that is assigned to the most recent log.
To check the log, click View > Error Log in the Control Builder window to open the log.

103
8 PEER CONTROL DATA INTERFACE TROUBLESHOOTING

8.4 Fixing common problems

This section identifies some common problems and describes how you might fix them.

Related topics
“Loss of power” on page 104
“Loss of communications” on page 104

8.4.1 Loss of power

The power supply has failed or the main power source has been shut down or is experiencing a brownout or
blackout condition.

Diagnostic Check In the Monitoring tab, the PCDI_MASTER device icon turns red.
Cause Main power source has been disconnected or shut down either manually or temporarily by
brownout or blackout condition.
Solution Re-connect the main power source or turn it On or wait for temporary brownout or blackout
condition to pass.

8.4.2 Loss of communications

No device data is being processed

Diagnostic Check In the Monitoring tab, the PCDI_MASTER device icon turns red.
In Station Event Summary, event error is logged
Cause 1 Broken or disconnected cable.
Solution Repair broken cable or connect cable, as applicable.
Cause 2 Intermittent communications timeout in device.
Solution For redundant devices, switchover to secondary device.
Try cycling power to the device. Replace the device, if fault persists.
Initiate a MODBUS loopback test on each end device to check if device can be reached.

104 www.honeywell.com
 8 PEER CONTROL DATA INTERFACE TROUBLESHOOTING

8.5 Getting further assistance

Related topics
“Guidelines for requesting support” on page 105

8.5.1 Guidelines for requesting support

If you cannot resolve a problem using this guide, you can request support from your Honeywell Solution
Support Center.
When requesting support, please supply as many relevant details as possible, including:
• Short summary of the problem
• Product Name and release.
• Recent changes, such as upgrades/service packs, to Experion software, Windows or other applications.
• Subsystem and its version/build, if the problem relates to a particular subsystem, such as Station or Quick
Builder.
If the problem relates to Display Builder, please specify whether it is HMIWeb Display Builder (for
HMIWeb displays) or Display Builder (for DSP displays).
• Operating system, variant and service pack, for example 'Windows 2000 Server, SP5'.
• Instructions on how to reproduce the problem. If the problem is reproducible, please supply step-by-step
instructions - the more detailed the steps the better.
• Diagnostic package which contains any relevant logs.

105
8 PEER CONTROL DATA INTERFACE TROUBLESHOOTING

106 www.honeywell.com
9 Notices

Trademarks
Experion® and SafeBrowse® are registered trademarks of Honeywell International, Inc.

Other trademarks
Microsoft and SQL Server are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Trademarks that appear in this document are used only to the benefit of the trademark owner, with no intention
of trademark infringement.

Third-party licenses
This product may contain or be derived from materials, including software, of third parties. The third party
materials may be subject to licenses, notices, restrictions and obligations imposed by the licensor. The licenses,
notices, restrictions and obligations, if any, may be found in the materials accompanying the product, in the
documents or files accompanying such third party materials, in a file named third_party_licenses on the media
containing the product, or at http://www.honeywell.com/ps/thirdpartylicenses.

Documentation feedback
You can find the most up-to-date documents on the Honeywell Process Solutions support website at:
http://www.honeywellprocess.com/support
If you have comments about Honeywell Process Solutions documentation, send your feedback to:
[email protected]
Use this email address to provide feedback, or to report errors and omissions in the documentation. For
immediate help with a technical problem, contact your local Honeywell Technical Assistance Center (TAC).

How to report a security vulnerability

For the purpose of submission, a security vulnerability is defined as a software defect or weakness that can be
exploited to reduce the operational or security capabilities of the software.
Honeywell investigates all reports of security vulnerabilities affecting Honeywell products and services.
To report a potential security vulnerability against any Honeywell product, please follow the instructions at:
https://honeywell.com/pages/vulnerabilityreporting.aspx
Submit the requested information to Honeywell using one of the following methods:
• Send an email to [email protected].
or
• Contact your local Honeywell Technical Assistance Center (TAC) listed in the “Support” section of this
document.

107
9 NOTICES

Support
For support, contact your local Honeywell Process Solutions Customer Contact Center (CCC). To find your
local CCC visit the website, https://www.honeywellprocess.com/en-US/contact-us/customer-support-contacts/
Pages/default.aspx.

Training classes
Honeywell holds technical training classes about Experion LX. These classes are taught by experts in the field
of process control systems. For more information about these classes, contact your Honeywell representative, or
see http://www.automationcollege.com.

108 www.honeywell.com