NPGC Specification Guide Cover_Ver 14_Layout 1 5/1/14 12:02 PM Page 1

Specification Guide
Specification
Guide Epicenter®
Epic® Casegoods
Exhibit™ Wall Rail Solution
Renegade™ Casegoods
WaveWorks® Casegoods

Effective June 3, 2013

www.NationalOfficeFurniture.com
1205 Kimball Boulevard, Jasper, IN 47549
800.482.1717 Fax 812.482.8800
©Kimball International, Inc. 2014
Printed in the USA
Form No. NSPEC Ver. 14
A Unit of Kimball International
Effective June 2, 2014
Limited Lifetime Warranty For more information about our products and services or to find At National, sustainability is embedded throughout the professional and
a certified National® dealer near you, please visit us at personal fabric of our lives. That extends from our products and processes
www.NationalOfficeFurniture.com or contact our Customer Service to the materials we provide you showcasing our solutions, such as this
Team at 800.482.1717. price list. It is printed on paper and is certified by the Forest Stewardship
Council (FSC®), which lends the assurance of being sourced from sustainably
managed forests.

National warrants that each piece of furniture will be free from defects in workmanship given normal use and care for as long as you, the original Intellectual Property This price list is available in printed form; however, we encourage you to
customer, owns and uses the product. conserve natural resources with us and consult the online version at
Acquaint®, Admire®, Arlington™, Arrowood™, Aurora®, Barrington®,
www.NationalOfficeFurniture.com/Resources.
Captivate®, Casbah®, Chameleon™, Cinch®, Clever®, Confide®, Davari®,
Normal use is defined as the equivalent of a single shift, 40 hour work week. In the event that a product is used more than normal use, the applicable
Eloquence®, EnvyWorks®, Epic™, Epicenter®, Escalade®, Exhibit™, Perhaps we’ve sent you more copies than you find necessary, or
warranty period will be reduced to 12 years and items that fall under different warranty limitations, as listed below, will be reduced to one-third
Flourish®, Franklin™, Fuel®, Fringe™, Gotcha™, Hiland™, IntegraClear®, you no longer wish to receive our mailings. If so, please email us at
(ex: Wood chair frames will be 4 years instead of 12 years). National, at its option, will repair or replace with comparable product any product,part
Jiminy™, Journey®, Justice®, Medalist™, Mix-it®, Monterrey™, Myriad™, [email protected]. And as always, when you
or component shipped after September 1, 2000, if the claim is eligible under the conditions of this warranty. This warranty is valid only if the product
Pegos™, Pennant™, Remedy®, Renegade™, Reno®, Respect®, Result®, no longer have a need for this catalog, please recycle it.
is given proper care and maintenance.
Roosevelt™, Staccato™, Swift™, Tag®, Timberlane™, Trimph™ and
Read more about our journey to create a better tomorrow at
WaveWorks® are registered trademarks of National Office Furniture.
Limitations Engineer-to-Order Products www.NationalOfficeFurniture.com/Sustainability.
Trademarks of other parties are identified wherever possible and National
Twelve Years Wood Chair Frames National warrants all Engineer-to-Order products acknowledges their rights.

Ten Years Seating Controls, Wood Veneers and Laminates to be free from defects in workmanship given normal use BLOCKaide™ and Terratex® are registered trademarks of Interface, Inc.
and care for 3 years of single shift service.
Five Years Mechanical and High Wear Parts Such As: Brisa®, Brisa® Distressed, Promessa® and Ultraleather™ are registered
Electrical Components, Polymer Based trademarks of Ultrafabrics, LLC.
Components, Pneumatic Cylinders, Finish Warranty Byrne Interlink® is a registered trademark of Byrne Electrical Specialists, Inc.
Swivel Arm Pads, Casters, Chair Glides,
Minor variations in finish color may occur due to the unique Corian® is a registered trademark of E.I. du Pont Nemours and Company.
Textiles, Foam, Covering Materials
texture and grain of wood.
and Decorative Trim Cradle to Cradle™ is a registered trademark of McDonough Braungart Design
Chemistry, LLC.
Exclusions
Follow these procedures to process warranty issues: Crypton®, Crypton® Green and INCASE™ are registered trademarks of
This warranty does not apply to: Crypton, Inc.
1. Contact National Customer Service (800.482.1717)
• Damage caused by a carrier and provide them with the serial number from the Hi-Loft™, Hi-Loft2™, PERMABLOK3®, SILVERGUARD® and Silvertex™ are
product in question and the purchase order number registered trademarks of Spradling Holdings, Inc.
• Normal wear and tear which is to be expected during
or acknowledgement number and a detailed description Hilti® Toggler® is a registered trademark of Hilti Corporation.
the period of ownership
of the warranty issue. Serial numbers are mandatory
• Appearance, durability, quality, behavior, colorfastness before the claim can be processed. Indoor Advantage™ is a trademark of Scientific Certification Systems.
or any other attribute of COM (Customer’s Own Materials) Intercoupler™ is a trademark of Power Logic SA (Pty), Ltd.
2. Customer Service will determine and pre-approve all
or any other non-standard National material (including Arc-Com,
resolutions to the claim such as replacement units, LEED® is a registered trademark of the U.S. Green Building Council.
Stinson, Maharam, Momentum, and Ultrafabrics) specified
service parts, labor and repair charges. Upon approval,
by the customer after application to a National product level® is a registered trademark of BIFMA International.
resolutions will be assigned an uthorization number.
• Color, grain or texture of wood, laminate and other Post-it® and Scotchgard™ are registered trademarks of 3M.
3. The authorization number must be included on all invoices
covering materials
for reimbursement. Any unauthorized charges will not be the Repreve® and U Trust™ are registered trademarks of UNIFI, Inc.
• Non-compliance with installation and maintenance responsibility of National. Silverguard® is a registered trademark of Life Bioscience USA, LLC.
instructions
Velcro® is a registered trademark of Velcro Industries B.V.
• Electrical grommets where the box has been opened
As the manufacturer of your furniture, we stand behind
• Damages or failures resulting from modifications, alterations,
our craftsmanship and pledge to do everything we can
misuse, abuse or negligence or improper care and maintenance
to resolve any problems you may have within the terms
of our products
of this warranty as quickly as possible.

NOTE: If using a protective glass top, always place felt spacer pads
under the glass to allow the wood to breathe. A glass addition There are no other warranties except as expressly set
has the potential to accentuate deflection. forth here, either expressed or implied including any
warranty of merchantability or fitness for any particular
purpose. We exclude and will not pay consequential
Gotcha™ 24 Hour Use Seating
or incidental damages under this warranty.
Warranty on Gotcha 24 Hour Use models is 5 years from
date of purchase for seating controls and pneumatic National Office Furniture
cylinders and 2 years from date of purchase for casters, 1205 Kimball Boulevard
textiles and foam. Jasper, Indiana 47549
800.482.1717
Fax 812.482.8800
www.NationalOfficeFurniture.com
 Table of Contents

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

CONSOLIDATED STATEMENT OF LINE . . . . . . . . . . . . . . . . . . . . . . . . 6-18

PRODUCT OVERVIEWS

Exhibit™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
WaveWorks® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Epic™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23
Epicenter™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
Renegade™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PRODUCT INTEGRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-31

SUPPORT AND LOAD

Exhibit Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35

WaveWorks and Epic Support . . . . . . . . . . . . . . . . . . . . 36-37
Epicenter Support . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-41
Renegade Support . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-43
POWER AND DATA

Exhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
WaveWorks, Epic and Renegade . . . . . . . . . . . . . . . . . . 46-47
Epicenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-49
PRODUCT SPECIFICATION

Exhibit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-56
WaveWorks and Epic. . . . . . . . . . . . . . . . . . . . . . . . . . 57-65
Epicenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-73
Renegade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74-76
Cable Management/Work Tools and Accessories . . . . . . . 77-79

National Office Furniture—Specification Guide 1

 Introduction

Welcome to Ultimate Flexibility Quality, Reliability and Sustainability . . . It’s in There

You’re here for a reason. You have something cool in mind and you want to You have enough things to worry about as you plan your space, so by
make it happen. You’re in the right place. At National, we like to make it choosing National you have the assurance of quality, reliability and
happen by making it as easy as possible to specify our furniture to fit your sustainability - enabling you to focus on your job.
design and budget goals. We understand the importance of planning and
the value of a quarter inch of space; it does matter. That’s why we’ve Our products meet and exceed industry standards for performance and
developed solutions that flex to various applications and uses. We have a durability. National is deeply committed to social and environmental
sea of sensible choices that offers unlimited configurations without being stewardship. So, you can plan on National being there for you and the
overwhelming. Let’s plan a spectacular space together. environment.

Our products ensure the health and well-being of building occupants and
the environment, and have earned numerous independent third-party
The Choice is Yours certifications including:
• the Indoor Advantage™ label (meets indoor air quality criteria)
This guide features four product collections that work independently or can
be integrated: Epic, WaveWorks, and Renegade Casegoods, Epicenter and • Forest Stewardship Council (FSC®) certification signifying
the Exhibit Wall Rail Solution. This allows you to design freely creating sustainable forestry practices
designs with layered surfaces, multiple storage solutions and a combination • ANSI/BIFMA e3 Sustainability Standard level® 2 or level® 3
of materials such as wood, metal, glass, resin and laminate. Exhibit certification
provides a unique solution by using the wall to support casegoods and
storage along with inserts for sharing ideas, displaying information and For detailed certification information by product series,
housing organizational tools. visit NationalOfficeFurniture.ecoscorecard.com.

Other benefits of specifying our products include: To measure our progress, we annually publish a detailed Corporate Social
Responsibility (CSR) report that offers a thorough analysis of our
• expansive product offering including unique storage options,
performance in the areas of zero-waste operations, life cycle assessments,
worksurface shapes, and surface materials
chemicals of concern identification, energy evaluation and more. To access
• maximize the use of space with the modular nature of these this report, visit our website at NationalOfficeFurniture.com/Sustainability.
products
• lighten the overall aesthetic with open support bases and use of
wall rail allowing more light to enter the workspace
• design specialized training, collaborative, and conferencing areas
• wall rail mounting provides easy access to building power and data

Get Comfortable: Planning Simplified

Designed to simplify the specification process by answering common

questions about individual product lines and how products can integrate,
this specification guide offers an organized, systematic approach to product
planning. The consolidated statement of line presents the components in
the order in which they are most effectively specified, while the overview
configurations show specific details about each series. It also provides
critical information about:
• using Exhibit as the foundation for supporting upper storage and
worksurfaces
• support and load requirements for fixed-wall and freestanding
applications
• power and data planning considerations
• Epicenter applications

And, don’t forget about the power and data conveniences and accessories.
Considering how you’ll incorporate these elements into your design and
their appropriate use will only enhance your customer’s experience once the
product is in place. This guide outlines where these tools can be utilized.
• Organizational and work tools
• Vertical pigeon hole storage and other organizing stackers
• Exhibit tack board, marker board and slat wall inserts
• Privacy screens, monitor arms, keyboard trays and task lights
• Grommets and cable managers
• Epicenter capabilities

National Office Furniture—Specification Guide 3

 Consolidated Statement
of Line

National Office Furniture—Specification Guide 5

 Application Key
E Epic
R Renegade
Consolidated Statement of Line W WaveWorks

Nationals’ consolidated pallet of products provides a variety of solutions designed to accommodate any design challenge.
The following items are keyed to illustrate which components are available within each product line to help make your planning
and specification process simple.

Desks

Arc Top—Full Pedestal Arc Top—¾ Pedestal Full Pedestal ¾ Pedestal Glass Top Arc Top—Full Pedestal Arc Top—¾ Pedestal Full Pedestal
Left/Right Left/Right Left/Right Left/Right
RW R ERW RW W RW R ERW

¾ Pedestal U-Shaped U-Shaped U-Shaped P-Shaped P-Shaped P-Shaped J-Shaped

with Modesty Panel Worksurface Height Box/File Height with Modesty Panel Worksurface Height Box/File Height Worksurface Height
End Panel End Panel Left/Right End Panel End Panel End Panel
Left/Right Left/Right Left/Right
RW ERW ERW R ERW ERW R R

Corner Units

Corner Unit Extended Corner Unit

Full
Left/Right
RW RW

Returns and Bridges

Return Box/Box/File Return File/File Space Saver Return Space Saver Return Return Return Shell Bridge
Left/Right Full Pedestal File/File Full Pedestal Box/File ¾ Pedestal Box/File ¾ Pedestal Left/Right
Left/Right Left/Right Left/Right Left/Right
EW ERW R R RW RW ERW

Shells

Freestanding Freestanding Linkable Return Linkable Bridge Space Saver Credenza

Worksurface Height/ Worksurface Height Left/Right with Narrow/Narrow Linkable Return Worksurface Height/
Box/File Height Box/File Height Panels Left/Right Box/File Height
Full End Panels End Panel
Left/Right
RW R RW R R RW

6 National Office Furniture—Specification Guide

Application Key
E Epic
R Renegade
W WaveWorks Consolidated Statement of Line

Credenzas

Kneespace Kneespace Single Pedestal Single Pedestal Single Pedestal Single Pedestal Extended Credenza Media
Full Pedestal ¾ Pedestal File/File Box/File Lateral File Box/Box/File Left/Right
Left/Right ¾ Pedestal Left/Right File/File
Left/Right Left/Right
ERW RW ERW RW ERW EW E W

Buffet/Entertainment Storage Lateral File Lateral File/ ¾ Pedestal

Double Door
RW ERW ERW R R

Reception Units

ADA Main Shell Main Shell Return with Return Bridge with Counter Kits Transaction Counter
Left/Right Transaction Surface Left/Right Transaction Surface
Left/Right
W RW W RW RW W W

Set-on Surface Storage

38" High

1915⁄16"

Highback Organizer Highback Organizer Highback Organizer Highback Organizer Highback Organizer Highback Organizer Highback Organizer Highback Organizer
Resin/Glass Doors No Doors Sliding Doors Open Back Open Back Recessed Doors Metal/Laminate
No Doors Metal Flipper Doors
ERW RW ERW E W W W W

Corner Highback Corner Highback Corner Highback Corner Highback Corner Highback Bookcase with Bookcase with Open Bookcase
Organizer Organizer Organizer Organizer Organizer Glass Doors Doors
Glass Doors No Doors Extended
Left/Right
W W W R R W ERW ERW

National Office Furniture—Specification Guide 7

 Application Key
E Epic
R Renegade
Consolidated Statement of Line W WaveWorks

Set-on Surface Storage

50" High

Entertainment Highback Organizer Highback Organizer Corner Highback Corner Highback Bookcase with Bookcase with Open Bookcase
Cabinet Glass Doors Organizer Organizer Glass Doors Doors
Glass Doors
W W W W W W ERW ERW

Entertainment
Cabinet
W

Overhead/Set-on Surface Storage

13" High

Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage
Cabinet Cabinet Cabinet Cabinet Cabinet Cabinet Open Cabinet Cabinet
Wall Mount Sliding Doors No Doors Exhibit Mount Sliding Doors No Doors Sliding Doors Sliding Doors
Wall Mount Wall Mount Exhibit Mount Exhibit Mount Set-On Surface Set-On Surface
“O” Supports “U” Supports
E E E E E E E E

Overhead Storage Overhead Storage Overhead Shared Overhead Shared Overhead Shared Overhead Shared
Cabinet Cabinet Storage Cabinet Storage Cabinet Storage Cabinet Storage Cabinet
No Doors No Doors Sliding Doors Sliding Doors No Doors No Doors
Set-On Surface Set-On Surface Left/Right Left/Right Left/Right Left/Right
“O” Supports “U” Supports Set-On Surface Set-On Surface Set-On Surface Set-On Surface
“O” Supports “U” Supports “O” Supports “U” Supports
E E E E E E

Epicenter Overhead Storage

13" High

Overhead Storage Overhead Storage Overhead Shared Overhead Shared Overhead Storage Overhead Storage
Cabinet Cabinet Storage Cabinet Storage Cabinet Cabinet Cabinet
Sliding Doors No Doors Sliding Doors No Doors Single Sided Single Sided
Left/Right Left/Right Sliding Doors No Doors
E E E E E E

8 National Office Furniture—Specification Guide

Application Key
E Epic
R Renegade
W WaveWorks Consolidated Statement of Line

Overhead Storage (continued)

17" High, 18" High

Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage
Cabinet Cabinet Cabinet Cabinet Recessed Door Cabinet Cabinet Cabinet
Resin/Glass Doors Wall Mount Sliding Doors No Doors Exhibit Mount Glass Doors Exhibit Mount Sliding Doors
Wall Mount Wall Mount Wall Mount Metal Exhibit Mount Exhibit Mount
RW ERW E ERW W W EW E

Overhead Storage Overhead Storage

No Doors Flipper Door
Exhibit Mount Exhibit Mount
Metal
EW W

30" High

Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage Overhead Storage
Cabinet Cabinet No Doors Cabinet Cabinet No Doors
Glass Doors Wall Mount Wall Mount Glass Doors Exhibit Mount Exhibit Mount
Wall Mount Exhibit Mount
W W W W W W

Lateral Files and Storage Cabinets

Lateral File Lateral File Lateral File Double Door Unit Multi-File Storage Mixed Storage Freestanding Mobile Utility Cart
Two Drawer Three Drawer Four Drawer Cabinet Cabinet Box/File
ERW ERW ERW ERW ERW ERW E W

Mobile Computer Cart Lateral File Lateral File Lateral File Lateral File
Two Drawer Three Drawer Four Drawer Five Drawer
Metal Metal Metal Metal
W W W W W

National Office Furniture—Specification Guide 9

 Application Key
E Epic
R Renegade
Consolidated Statement of Line W WaveWorks

Vertical Storage Towers

405⁄16
" High, 5215⁄16
" High

Wardrobe/ Storage/ Storage/ Storage Front Bookcase Storage Front Bookcase 90° Storage 90° Storage 90° Storage
Storage Cabinet Wardrobe with Wardrobe with Wardrobe with Wardrobe with Bookcase/Wardrobe Bookcase/Wardrobe Bookcase
Single Door File/File File/File File/File File/File with File/File with File/File with File/File
Left/Right Left/Right Left/Right Left/Right Left/Right Left/Right Left/Right Left/Right
E E E E E E E E

90° Storage Storage Front Bookcase Storage Front Bookcase Wardrobe Cabinet Wardrobe Cabinet Wardrobe/ Storage Cabinet Storage/Lateral
Bookcase with File/File with File/File Double Door Double Door Storage Cabinet Double Door File Cabinet
with File/File Left/Right Left/Right Double Door
Left/Right
E E E E E E E E

Storage/Lateral Storage Cabinet Storage Cabinet

File Cabinet Bookcase with Bookcase with
File/File File/File
Left/Right Left/Right
E E E

537⁄8" High, 6515⁄16

" High

Storage Cabinet Storage/Wardrobe Storage Bookcase

File/File File/File Wardrobe
Metal Metal File/File
Metal
W W W

667⁄8" High

Wardrobe/Storage Storage/Wardrobe 90° Storage 90° Storage Wardrobe/Storage Storage Cabinet Storage/Lateral Wardrobe
Cabinet with File/File Bookcase/Wardrobe Bookcase Cabinet Double Door File Cabinet Double Door
Single Door Left/Right with File/File with File/File Double Door
Left/Right Left/Right Left/Right
ERW ERW ERW EW EW ERW ERW ER

10 National Office Furniture—Specification Guide

Application Key
E Epic
R Renegade
W WaveWorks Consolidated Statement of Line

Vertical Storage Towers

667⁄8" High

Storage Cabinet Storage Front Bookcase Storage Front Bookcase

with File/File Wardrobe with with File/File
Left/Right File/File Left/Right
Left/Right
EW E E

67¼" High, 79¼" High, 7911⁄16

" High

Wardrobe/Storage Storage/Wardrobe 90° Storage 90° Storage Wardrobe/Storage Storage Cabinet Storage/Lateral Storage Cabinet
Cabinet with File/File Bookcase/Wardrobe Bookcase with Cabinet Double Door File Cabinet with File/File
Single Door Left/Right with File/File File/File Double Door Left/Right
Left/Right Left/Right Left/Right
W W W W W W W W

Media Storage Tower

Single Door
(79 11⁄16" only)
Left/Right
W

Bookcases

One Shelf Two Shelf Bookcase Three Shelf Four Shelf Bookcase Five Shelf Bookcase
Open Bookcase Open Bookcase with Doors Open Bookcase Open Bookcase with Doors Open Bookcase with Doors
EW ERW W ERW RW W W W

Open Bookcase Open Bookcase Open Bookcase

Two Shelf Three Shelf Four Shelf
Metal Metal Metal
W W W

National Office Furniture—Specification Guide 11

 Application Key
E Epic
R Renegade
Consolidated Statement of Line W WaveWorks

Mobile Pedestals

Mobile Pedestal Mobile Pedestal Mobile Pedestal Mobile Pedestal Mobile Pedestal Mobile Pedestal w/Pull
File/File Box/File Box/File with Top Cushion Top Cushion Top Cushion Top
Metal
W W ERW ERW W W

Worksurfaces

Rectangular Tapered Angled Concave Corner Extended Corner Arc U-Shaped

EW E W E W EW EW W EW

Extended U-Shaped Elliptical U-Shaped P-Shaped Elliptical P-Shaped Extended P-Shaped Elliptical Extended 120° Corner J-Shaped
P-Shaped
E W EW W EW W W EW

Island Extension Round Half Round D-Shaped Quarter Round Extended Quarter Square Cornice Top
Round 15" and 24" Deep
W EW ERW W W W EW W

Component Top for Worksurface Wire

Lateral Files Manager Filler
R EW

Undersurface Storage Support

Worksurface Height

Box/Box/File File/File Support Pedestal Lateral File Double Door Unit Double Door Unit Bookcase Mixed Storage Cabinet
Sliding Doors
ERW ERW E ERW ERW E ERW ERW

12 National Office Furniture—Specification Guide

Application Key
E Epic
R Renegade
W WaveWorks Consolidated Statement of Line

Undersurface Storage Support

Worksurface Height

Multi-File Cabinet Box/File Storage Cabinet Box/Box/File File/File Lateral File Double Door Multi-File
Undersurface Metal Sliding Undersurface Undersurface Undersurface Undersurface Undersurface
Suspended Shelves Metal Metal Metal Metal Metal
ERW R EW W W W W W

Mixed Storage Open Bookcase Box/File

Undersurface Undersurface Undersurface/Hanging
Metal Metal Metal
W W W

Box/File Height

Storage Cabinet Bookcase Lateral File Box/File Box/Lateral File Box/File Box/Lateral File Box/File Bookcase
Metal Sliding Undersurface Undersurface Undersurface Undersurface
Shelves Metal Metal Metal
EW ERW RW EW E W W W

Surface Supports

End Panels Support Panels U-Style Supports Box/File Height T-Panel Support Corner Post Counter and Bar Height Static and Mobile
Supports Full and Box/File Metal Square and Round Column Legs
Heights Support Bases
EW EWR EWR EW EW W EWR EW

Static and Mobile Half Wood Counter and Bar Height Counter and Bar Height Counter and Bar Height Counter and Bar Height Counter and Bar Height Counter and Bar Height
Adjustable Height Support Base “H” Style “U” Style “U” Style Support Base Kits Support Base Kits Support Base Kits
Column Pin Legs End Supports End Supports End Supports “H” Style “U” Style “U” Style with Insert
with Insert
EW W EWR EWR EWR EWR EWR EWR

Double Depth Base Double Depth Base

28" High Model w/Insert
28" High Model
National Office Furniture—Specification Guide 13
 Application Key
E Epic
R Renegade
Consolidated Statement of Line W WaveWorks

Surface Supports

Static and Mobile Height Adjustable Counter and Bar Height X Base X Base Static and Mobile Adjustable Height
Four Star Bases Four Star Base Four Star Bases Adjustable Height Static and Mobile C-Legs Static C-Leg
Mobile Pin Adjustment
EWR EWR EWR EWR EWR EW EW

Static and Mobile Manual (Hand Crank) Electric Adjustable Manual (Hand Crank) Electrical Adjustable Disc Base Counter and Bar
T-Legs Adjustable Height Base Adjustable Height Height “L” Base Height Disc Base
Height Base “L” Base
EW EW EW EW EW EW EW

Soft Square Base Counter and Bar Height Worksurface Worksurface to Corner Support End Panel End Panel
Soft Square Base Undersurface Support Storage Bracket Privacy Panel Metal Box/File
Rail Metal
EW EW EWR EW EW W W

Half End Panel Support Panel Support Panel Return Support Panel Gusset Bracket Epicenter End Epicenter Mid
Metal Metal Box/File Metal Metal Support Privacy Support Privacy
Metal Panel Panel
W W W W W EW EW

14 National Office Furniture—Specification Guide

Application Key
E Epic
R Renegade
W WaveWorks Consolidated Statement of Line

Modesty Panels and Privacy Screens

Full Height Box/File Height 1⁄3 Height Modesty Mesh Modesty Panel 1⁄3 Height Metal 1⁄3 Height Resin Tapered Acrylic Rectangular Acrylic
Modesty Panel Modesty Panel Panel Modesty Panel Modesty Panel Privacy Screen Privacy Screen
EW EW W W EW EW ERW ERW

Rectangular Felt Edge Mounted Edge Mounted Edge Mounted

Privacy Screen Privacy/Modesty Privacy Screen Privacy Screen
Screen Rectangular Tapered
ERW ERW ERW ERW

Exhibit
Exhibit Rails

Exhibit Wall Exhibit Wall and

Rail Faceplate

Exhibit Inserts

Tack Board Inserts Marker Board Inserts Slat Wall Inserts Slat Wall with Organizer Shelf
Tack Inserts Inserts

Exhibit Worksurface Brackets and Trim

Full End Trim Trim Channels Single End Cap Vertical Cable Manager Worksurface Filler Strips
Mounting Bracket

National Office Furniture—Specification Guide 15

Consolidated Statement of Line

Epicenter
Epicenter and Brackets/Trim

Upper Epicenter Upper Epicenter Lower Epicenter Universal Epicenter Epicenter Epicenter Epicenter Filler Epicenter Trim Cap
Multi-Circuit Non-Powered Attachment Bracket Worksurface End Trim Strip Kit
Set Mounting Brackets

Epicenter Inserts and Screens

Tack Board Insert Marker Board Insert Slat Wall Insert Slat With Tack Insert Tapered Rectangular Single Sided Single Sided
Privacy Screen - Privacy Screen - Insert - Insert -
Epicenter Mount Epicenter Mount Tack Board Veneer

Single Sided Modesty Panel Insert Modesty Panel Insert

Insert - Veneer Laminate
Laminate

Epicenter Supports

Double Depth Base Double Depth Base Base Support Base Double Depth Base Base Epicenter Double Epicenter End Panel
28" High Model w/Insert 28" High Model 28" High Model 6" High Model 6" High Model Depth End Panel 28" High Model
28" High Model 28" High Model

Epicenter Double Epicenter End Panel Epicenter End Epicenter End Epicenter Mid Epicenter Mid
Depth End Panel 6" High Model Support Privacy Support Privacy Support Privacy Support Privacy
6" High Model Panel Panel Panel Panel

Epicenter Power and Data

Power Entry Whip Jumper Duplex Receptacles Power Pole Vertical Wire Horizontal Wire Hardwire Kit
Manager Manager

16 National Office Furniture—Specification Guide

 Consolidated Statement of Line

Accessories

Vertical Pigeon Organizing Stacker Lower Storage Tack Boards Marker Boards Slat Walls Task Lights Metal Storage Cubby
Hole Storage Cushion

Work Tools

Center Drawers Storage Trays Keyboard Tray Keyboard Tray/ Keyboard Kits Flexible Single Flexible Single
Mouse Pad Monitor Arm Monitor Arm
Pole Mount Grommet Pole Mount Clamp

Flexible Dual Flexible Dual Triple Mount

Monitor Arm Monitor Arm Monitor Arm Kit
Pole Mount Grommet Pole Mount Clamp

CPU Holder Metal Corner Sleeves CPU Cart Mobile Desk Pad Waste Container Pencil Tray Box Drawer Divider Overhead/Shelf
Divider

Deluxe Drawer
Organizer

Metal Work Tools

Shelf Single Side Tray Double Side Tray Pocket Organizer Slant Sorter Binder Shelf Marker Holder

Black and Clear Plastic Work Tools

Pencil Cup Legal Paper Accessory Tray Phone Holder Binder Shelf Slant Sorter
Tray

National Office Furniture—Specification Guide 17

Consolidated Statement of Line

Power/Data Products

Power/Data Center Convenience Corner Channel Power Director Power Center Power/ Power Tower Cable Managers
Outlet with Power Communication and Covers
Center

Byrne Interlink® One Touch Pivoting One Touch Pivoting One Touch Pivoting Byrne Interlink Byrne Interlink Power Grommet Powerlogic
System Power/Data Grommet Power Grommet Power Grommet IQ System IQ System (G23) Intercoupler™ System
(G17) (G172) (G173) Power/Data Power Grommet (Undersurface)
Grommet

Worksurface Undersurface Horizontal Wire

Grommets Wire Managers Manager

18 National Office Furniture—Specification Guide

 Product Overview

National Office Furniture—Specification Guide 19

Product Overview

Exhibit Wall Rail Solution

By making efficient use of wall space, Exhibit wall rails, inserts and worksurface mounting brackets
provide the infrastructure support within private offices and the perimeter foundation for many
environments. Exhibit may also be used at any height within training rooms, common areas,
mail/copy rooms, and conference space to support interaction.

Wall rails and inserts also capitalize on vertical wall space to support personal organization and
collaboration tools within the work space.

Exhibit wall rails, tack board inserts and HPL marker board inserts may be field scribed to adapt to
almost any wall length and configuration.

Upper rails provide support for overhead

storage anywhere along the rail
Full end trim and end caps
create a finished appearance Faceplates required to secure inserts
at the end of a run within wall rails

Tack board, marker board, organizer shelves, slat wall and

Lower rails provide slat/tack inserts provide personal organization and collaboration
support for worksurfaces
anywhere along the rail

Worksurface
mounting brackets Vertical cable
are available to manager conceals
provide attachment and routes task light cords
of a broad range of
worksurface types
and sizes

Upper wall rail

Work tools are available to
Faceplate attach anywhere along the slat
Full end trim wall insert

Inserts

Lower wall rail

Worksurface brackets

20 National Office Furniture—Specification Guide

 Product Overview

WaveWorks
WaveWorks Casegoods offer freestanding or Exhibit supported worksurfaces and storage options for
private office, collaborative and open plan environments. Conference and training solutions are also
provided through a variety of surface and support options.

WaveWorks metal storage and privacy components are also available to provide alternative solutions.

WaveWorks may be planned and specified using assembled or component products.

Modified sizing available on WaveWorks worksurfaces, modesties and end panels.

Overhead storage in set-on,

wall mount or Exhibit mount,
with or without doors Widths available to match worksurface widths

Tack boards and slat walls

Multiple storage height options
may be added

Set-on storage

Worksurfaces available
13⁄16" or 19⁄16"
thickness with wire
managers, surface
grommets, and below
surface cable
management (available
separately)
Several power/data
Multiple worksurface support
components are available
options available to provide
to bring access to the
proper support as well as
worksurface
unique aesthetics
Worksurface height storage

Choose from several worksurface

types, sizes and rim profiles
Freestanding storage:
From mobile pedestals, lateral files
and bookcases to wardrobes
and storage towers

Two undersurface storage heights available:

worksurface and box/file height
Overhead storage in set-on,
wall mount or Exhibit mount,
with or without doors

Modesty panels available

Box/File height storage

National Office Furniture—Specification Guide 21

Product Overview

Epic
Epic Casegoods offer freestanding or Exhibit supported worksurfaces and storage options for private
office, collaborative and open plan environments.

Epic’s footed base design offers a lighter aesthetic within the work space.

Epic may be planned and specified using assembled or component products.

Modified sizing available on Epic worksurfaces, modesties and end panels.

Choose from several

worksurface types, sizes
and rim profiles

Worksurfaces available
with integrated wire
managers, surface
grommets, and below
surface cable
management (available
Freestanding storage:
separately)
From pedestals, lateral files and bookcases
to wardrobes and storage towers

Modesty panels available Footed base design creates a

lighter scale aesthetic

Privacy screens available

Multiple worksurface support options
Worksurface height storage available to provide proper support as well
as unique aesthetics

Two undersurface storage heights available:

worksurface and box/file height

Box/File height storage

22 National Office Furniture—Specification Guide

 Product Overview

Epic
Epic Casegoods offer overhead storage in set-on, wall mount or Exhibit mount with hinged doors,
sliding doors or without doors.

Overhead storage in set-on, wall

mount or Exhibit mount with
hinged doors, sliding doors or
without doors

Overhead set-on storage available with

“U” style stanchions (worksurface defacing)
and “O” style stanchions (non-defacing)
options that are available with sliding
doors or without doors

Choose from several worksurface

types, sizes and rim profiles.
Multiple worksurface support Worksurfaces available with integrated
options available to provide wire managers, surface grommets and
proper support as well as unique below surface cable management
aesthetics (available separately)

National Office Furniture—Specification Guide 23

Product Overview

Epicenter
Epicenter mounts to WaveWorks or Epic undersurface storage and support bases within private office,
collaborative and open plan environments.

Epicenter is supported by the undersurface storage or support bases and provides support for
perpendicular worksurfaces and power/data capabilities.

Available with a multi-circuit solution or non-powered. Powered Upper Epicenter frames may be
connected directly to building power at the floor, wall or ceiling to manage and deliver power and
data to the beltline of the workstation.

Privacy screens attach Worksurface mounting

anywhere along the top brackets attach to
of the Epicenter top cap the slat insert of
the Epicenter frame
Epicenter overhead allowing the
storage straddles worksurface to
the Epicenter frame attach anywhere

WaveWorks or Epic box/file

height undersurface storage
without the end panel grommet Power and data access is available
or back panel option on one or both sides of the
powered Epicenter

End trim

Epicenter filler strip

Upper Upper inserts available in tack board, marker board,

Epicenter slat wall and slat/tack board

Accessories and work tools are available to attach

anywhere along the slat insert

Power and power/data options for tack board

and slat/tack board insert

Epicenter trim caps must be specified separately

to go on top of the Epicenter. The trim cap runs
below the overheads and the Epicenter mounted
privacy screen is attached to the trim cap

WaveWorks or Epic worksurface

height undersurface storage
without the end panel grommet

24 National Office Furniture—Specification Guide

 Product Overview

Epicenter
Epicenter can be specified for a double or single sided application. Epicenter double sided consists of
an Upper Epicenter that must be supported by undersurface storage or Epicenter supports and a
worksurface.

Epicenter single sided consists of an Upper and Lower Epicenter that must be supported by
undersurface storage or Epicenter supports and a worksurface. Upper and Lower Epicenters must be
specified at the same widths.

Modesty panel insert sizing must be specified after the undersurface storage or Epicenter supports are
specified. Modesty panel inserts will run between undersurface storage and end support panels.
Modesty panel inserts will run behind Epicenter support bases. Modified sizing available on modesty
panel inserts.

Epicenter trim caps must be

specified separately to go on
top of the Epicenter

Privacy screens available

Power and data access is available

on one or both sides of the
powered Epicenter

Epicenter trim cap

must be specified Mid support privacy
separately panels are available
in double or single
sided Epicenter
applications

Epicenter modesty Power and power/data

panel insert available pass through is available
in modified sizing when specifying an Epicenter
on each side of the mid
support privacy panel
Epicenter end End support privacy panels provide
trim must be worksurface end support and also
specified separately privacy. Available in double or single
sided Epicenter applications

National Office Furniture—Specification Guide 25

Product Overview

Renegade
Renegade Casegoods offer freestanding desks and storage options for private office, collaborative and
open plan environments.

Renegade may be planned and specified using assembled or component products.

Renegade desking shells may also be used with WaveWorks and Epic undersurface storage

Several single circuit Privacy panels available

power/data components are
available to bring access to Use cushion for
the surface guest seating

Freestanding box/file
height shell

Storage widths and depths are

sized for a clean vertical line Shells may be
linked together to
create collaborative
Shells with box/file height Choose from several worksurface
environments
or full surface height end types and sizes, in shell or desk
panels are available configurations

Overhead storage in set-on or

wall mount with or without doors
Freestanding storage:
From lateral files and bookcases
to wardrobes and storage towers

Tack boards may be added

Can be wall mounted or within
a highback organizer

Set-on storage

Desks may be specified with

suspended box/file or full
height pedestals

26 National Office Furniture—Specification Guide

 Product Integration

National Office Furniture—Specification Guide 27

Product Integration

Integration
Selected products within WaveWorks, Epic, Renegade and Exhibit may cross over between product
lines to offer solutions that achieve greater flexibility, aesthetics and price points.

You may select worksurfaces from one product line and utilize undersurface storage from another
product line. Or utilize the undersurface storage and worksurfaces from one product line and
incorporate set-on and wall mount storage from another line.

You may even layer heights of surfaces and storage to realize your own unique design solution. We
do recommend that you consider the base design of each storage product when considering which
components to place directly adjacent to each other.

Here are some standard typical examples showing the integration of components between product
lines.

Epic and Exhibit

Epic Exhibit
mounted storage

Exhibit wall rails

Tack board insert field scribed to match
Exhibit inserts
Epic knife rim worksurface depth

Exhibit full end trim

Specify the softened rim

profile for worksurfaces
on box/file height
undersurface storage Exhibit supported Epic knife
rim worksurface
Epic box/file height
pedestals
Choose any appropriate
worksurface support to fit your
design requirements
Several modesty panel
options are available

Epic and WaveWorks

WaveWorks set-on
overhead storage

Epic knife rim

surfaces

Several modesty panel

options are available

Worksurface height Choose any appropriate

Epic support pedestals worksurface support to fit your
design requirements

Use any freestanding storage components

28 National Office Furniture—Specification Guide

 Product Integration

Epic, WaveWorks and Exhibit GRAPHIC KEY

Graphics are illustrated with a shaded
technique to help you quickly identify
which products to focus on.

Primary Secondary or
product supporting
product

Tack Boards may be

field scribed to match WaveWorks Exhibit
Epic knife rim mounted storage
worksurface depth

WaveWorks
Exhibit wall rails set-on storage

Exhibit inserts

Exhibit full end trim Epic worksurface

height storage

Several modesty panel Epic support pedestals

options are available

Epic knife rim surfaces

Renegade and WaveWorks

WaveWorks box/file
height metal storage

Several privacy panel

options are available

Renegade shells with

Renegade shells with box/file height and
box/file height end panels worksurface height
end panels

National Office Furniture—Specification Guide 29

Product Integration

WaveWorks and Epicenter Double Sided Application GRAPHIC KEY

Graphics are illustrated with a shaded
technique to help you quickly identify
which products to focus on.

Primary Secondary or
product supporting
product

WaveWorks and Epicenter Double Sided Application

WORKSURFACE HEIGHT

Epicenter mounted
privacy screen
Upper Epicenter
WaveWorks worksurfaces must
be specified with a modified WaveWorks
depth of 227⁄16" or 285⁄8" to worksurfaces
align with the Epicenter

End trim model must

be ordered based upon WaveWorks freestanding
application storage components

WaveWorks worksurface Choose any appropriate

height undersurface worksurface support to fit your
storage without the end design requirements
panel grommet or back Wire manager filler must be
panel option specified separately to cap
the end of a worksurface
when a wire manager is
specified

WaveWorks and Epicenter Double Sided Application

BOX/FILE HEIGHT
Epicenter
overhead storage

WaveWorks worksurfaces
End trim model must supported by Epicenter
be ordered based upon
application

WaveWorks worksurfaces must

WaveWorks box/file be specified with a modified
height undersurface depth of 227⁄16" or 285⁄8" to
storage without the end align with the Epicenter
panel grommet or back Several modesty panel
panel option options are available

30 National Office Furniture—Specification Guide

 Product Integration

WaveWorks/Epic and Epicenter Single Sided Application GRAPHIC KEY

Epicenter single sided application mounts to WaveWorks or Epic storage within private office, Graphics are illustrated with a shaded
collaborative and open plan environments. technique to help you quickly identify
which products to focus on.
Epicenter single sided must be supported by undersurface storage or Epicenter supports and a
worksurface.
Primary Secondary or
Epicenter single sided consists of an Upper and Lower Epicenter; Upper Epicenter inserts for the user product supporting
side and single sided inserts for the approach side. product

Available with a multi-circuit solution or non-powered in the Upper Epicenter section. Powered
Epicenter frames may be connected directly to building power at the floor, wall or ceiling to manage
and deliver power and data to the beltline of the workstation.

Modesty panel insert sizing must be specified after the undersurface storage or Epicenter supports are
specified. Modesty panel inserts will run between undersurface storage and end support panels.
Modesty panel inserts will run behind Epicenter support bases.

Single sided Epicenter overheads have an unfinished back. An overhead back panel must be specified
separately when using the overhead in an open plan.

WaveWorks and Epicenter Single Sided Application

WORKSURFACE HEIGHT
Epicenter mounted privacy
screens must be mounted to
the Epicenter trim cap

Epicenter modesty panel

End trim model must insert available in modified
be ordered based upon sizing
application

Epic and Epicenter Single Sided Application Epicenter single sided

BOX/FILE HEIGHT overhead storage

Epicenter single sided

overhead back panel;
must be specified separately

End trim

Edge mount modesty/

privacy screens available

National Office Furniture—Specification Guide 31

 Support and Load

National Office Furniture—Specification Guide 33

Support and Load

Exhibit Wall Rail Solution

Exhibit consists of upper and lower rails that REQUIRED
support worksurfaces, overhead storage
components and Exhibit inserts. Maximum 24" on center
Secured
Exhibit rails attach at desired height directly to
load bearing walls constructed of wood or metal Wood or metal studs,
studs, poured concrete or concrete block walls concrete block or
with fasteners appropriate to the wall material. poured concrete
construction
WALL REQUIREMENTS Exhibit rails

STUD WALLS
Wood studs must be a minimum of 2 x 4’s
secured to the floor and ceiling. Rails fastened every
Maximum height of 14’. 24" maximum

METAL STUDS
Metal studs must be minimum 20 gauge “C”
Secured
channel secured to the floor and ceiling. Maximum 14’
Maximum height of 14’.

POURED CONCRETE AND CONCRETE BLOCK

ATTACH
Attach rails with appropriate fasteners for wall
material.
6" maximum
STRENGTH
Walls must resist no less than 5 lbs. per square
foot of force applied perpendicular to the wall
and the deflection can not exceed 1⁄240 of the
span for brittle finishes and 1⁄120 of the span for
flexible finishes.

ATTACHMENT WIDTHS
Rails must be fastened a maximum of every 24". 18" minimum 30" minimum
Rails may not extend more than 6" beyond
attachment point.

WIDTHS
Properly fastened, there is no maximum length
requirements for Exhibit rail runs.

MINIMUM WITH INSERT ONLY. Inserts only Components support

Minimum rail length is 18" on 16" centered
mounting points.
HEIGHTS
MINIMUM TO SUPPORT COMPONENTS.
Minimum rail length is 30" centered on 24"
mounting points.

MOUNTING HEIGHTS
Standard height to the center of the lower rail is
28½" from the finished floor to accommodate
undersurface storage. 66½"

Upper rail height is determined by the insert 661⁄16"

785⁄16"
height, storage component supported and 63¾"
adjacent freestanding components. 777⁄8"

Refer to product specification section page 42

for information on proper heights to coordinate
28½"
WaveWorks and Epic components as well as bar,
counter and worksurface height applications.

34 National Office Furniture—Specification Guide

 Support and Load

Exhibit Rail Attached Undersurface support rail

Worksurface Support Lower rail
Worksurface brackets
Exhibit lower rails will support worksurfaces in
linear and perpendicular configurations anywhere
Any WaveWorks or
along the rail.
Epic worksurface

WORKSURFACE BRACKETS
Any width or depth WaveWorks or Epic
worksurface may be attached to the Exhibit
lower rail when supported by worksurface
brackets.
Up to 48" requires 2 brackets.
Up to 72" requires 3 brackets.
Longer than 72" requires 4 brackets.

EXHIBIT RAIL ATTACHED OVERHEAD STORAGE

Exhibit upper rail will support WaveWorks and

Epic overhead storage components anywhere Upper rail
along the rail. Gang multiple components
WaveWorks or Epic
together for a clean, straight run.
overhead storage

OTHER SUPPORT ISSUES

Exhibit slat wall inserts will support any
combinations of work tools and one slat mount
monitor arm every 24".

EXHIBIT SLAT WALL INSERTS

Wall fasteners are NOT required under the
following conditions:
• If slat wall inserts are to support less
than 40 lbs., wall fasteners are not REQUIRED SUPPORT
required. 13⁄16" thick.
• When weight is distributed evenly above Require support every 48".
and below center of slat wall, the slat 19⁄16" thick.
wall can hold up to 160 lbs. without Require support every 60".
using wall fasteners. At least half of the
weight must be applied above center of Undersurface support rail available to support Slat wall insert supports work tools
slat wall. Deflection or bowing occurs surfaces up to 72" (a work tool can hold up to 8 lbs.)
when not enough counterweight is Consider additional support where heavy loads
applied to the upper half of slat wall. are anticipated.
• Any slat wall inserts used in conjunction
with overhead storage units will not need Surface support is required wherever 2 surfaces
wall fasteners. Overhead units must fully meet end-to-end.
cover the slat wall. FASTENERS
In place of end panels, corner surfaces may be
Dry wall – #8 x 1½" plastic toggle anchor, with
Wall fasteners are to be used under the following supported by a support base at the back corner
black panhead screw
conditions: when connected to an adjacent surface.
• If slat wall inserts are to support 160 lbs. Wood Stud – #8 x 1½" black panhead screw
or more, wall fasteners are to be used. EXHIBIT SLAT WALL INSERTS COMBO SLAT/TACK
• Bottom loading, (placing the majority of Concrete or brick – #8 x 1" plastic conical anchor
Wall fasteners are NOT required under the
load below centerline of slat wall), causes kit with black panhead screw
following conditions:
the slat wall to deflect or bow from fixed • If slat wall inserts are to support less
wall. If slat wall inserts are to be loaded than 40 lbs., wall fasteners are not
with more than 50% of load on the required.
bottom half, wall fasteners must be
installed. Wall fasteners are to be used under the following
conditions:
When required, two fasteners are required per • If slat wall inserts are to support 40 lbs.
slat wall insert. Fasteners are to be inserted in or more, wall fasteners are to be used.
the center slat, approximately 1 inch off of edge
“U” trim, or to nearby stud. When required, two fasteners are required per
combo/tile slat wall insert. Fasteners are to be
inserted in the top slat, approximately 1 inch off
of edge “U” trim, or to nearby stud.

National Office Furniture—Specification Guide 35

Support and Load

WaveWorks and Epic Freestanding

Component Worksurface
Support
Follow these guidelines when planning for Epic
and WaveWorks component worksurfaces.

“L” Return “L” Box/File

CONFIGURATION TYPES
Freestanding
Linear runs
“L” Shaped return or box/file height support
“U” Shaped bridge or return

WORKSURFACE SUPPORT
All surfaces, in any configuration, must be “U” Bridge “U” Return
supported at a minimum of one end by an
Exhibit rail, a support pedestal, support base,
end panel, or a metal support base.

Undersurface support rail available to support

surfaces up to 72".

REQUIRED SUPPORT
13⁄16" thick;
Require support every 48".
19⁄16" thick; Linear
Linear
Require support every 60".

Undersurface support rail available to support

surfaces up to 72".

Consider additional support where heavy loads

are anticipated.

Surface support is required wherever 2 surfaces

meet end-to-end.

In place of end panels, corner surfaces may be Linear Linear

supported by a support base at the back corner
when connected to an adjacent surface.

WORKSURFACE BRACKETS
Flat brackets connect worksurfaces in “L” and
“U” configurations and are shipped with
worksurfaces when specified as an extension
(qty. 2) or filler (qty. 4).

Corner support panel

TOP DOWN VIEW TOP DOWN VIEW 48" maximum 60" maximum
Support Undersurface
required Support Rails Support Support
required required

13⁄16" thick surface 19⁄16" thick surface

Support
required
Support
required
End support End Support Flat
required Required Any surface end-to-end brackets
Support base
WITH SUPPORT PANELS OR... WITH UNDERSURFACE SUPPORT RAILS

36 National Office Furniture—Specification Guide

 Support and Load

WaveWorks and Epic

Component Storage Support
Follow these guidelines when planning for Undersurface support rails will not provide proper EXHIBIT MOUNT
overhead and set-on storage components. support for set-on storage. Support panels are Exhibit upper rail
required when the unsupported span is greater Exhibit mount
PROPER SUPPORT than 48 inches, not an undersurface support rail. WaveWorks or Epic
EXHIBIT RAIL MOUNTED overhead storage
Any WaveWorks or Epic Exhibit mount overhead WALL REQUIREMENTS
storage component may be supported by Exhibit STUD WALLS
upper rails. Wood studs must be a minimum of 2 x 4’s
Consider rail height when planning for adjacent secured to the floor and ceiling.
set-on and freestanding storage for proper Maximum height of 14’.
alignment.
METAL STUDS
WALL MOUNTED Metal studs must be minimum 20 gauge “C”
Any size WaveWorks and Epic overhead storage channel secured to the floor and ceiling.
Maximum height of 14’. WALL MOUNT
component may be attached at desired height
Studs, poured concrete
directly to load bearing walls constructed of
POURED CONCRETE AND CONCRETE BLOCK or concrete block wall
wood or metal studs, poured concrete or concrete
block walls with fasteners appropriate to the wall Attach with appropriate fasteners for wall
material. material. Fasten
minimum two
Consider mounting height when planning for
STRENGTH locations
adjacent set-on and freestanding storage for
Walls must resist no less than 5 lbs. per square
proper alignment.
foot of force applied perpendicular to the wall WaveWorks or
and the deflection can not exceed 1⁄240 of the Epic overhead
SET-ON OVERHEAD STORAGE WITH STANCHIONS span for brittle finishes and 1⁄120 of the span for
Overhead stanchions are specified as “U” storage
flexible finishes.
(defacing) stanchions or “O” (non-defacing)
stanchions.
ATTACHMENT
“U” stanchions must be mounted through the All wall mounted overhead storage must be
worksurface (defacing). fastened directly into studs, poured concrete or
“O” stanchions are attached to the worksurface concrete block at a minimum of two locations
with double sided tape (non-defacing). with fasteners appropriate for the wall material.

SET-ON OVERHEAD STORAGE/HIGHBACKS

Overhead storage and bookcase units are sized in
6" increments.
All WaveWorks and Epic set-on overhead storage
may be used on any properly supported
WaveWorks or Epic worksurface configuration and
any credenza or Renegade shell, with the
exception of table desks or glass top desks.
Consider worksurface grommet locations when Support panel
planning for set-on overhead storage. Two
End panel or End panel or
storage units side-by-side may interfere with a support pedestal
support pedestal
center grommet on a worksurface.
Highback units sitting on built-up credenzas with
20 inch or less deep worksurfaces require support
pedestals. End panels are not acceptable.

PROPER SUPPORT
An end panel, support panel, or support pedestal
must be located under the end panels of the
storage unit for proper support.
Match unit width to worksurface width or use a
support panel below the end panel of the storage
unit or bookcase.
Side panel of set-on surface storage must be Support panel
within 6" of undersurface support/leg.
Set-on surface storage cannot be used in table End panel or End or support panel
desk application. support pedestal

National Office Furniture—Specification Guide 37

Support and Load

Epicenter Support
(Double Sided)
Upper Epicenter frame must be supported on both
Upper
sides by WaveWorks or Epic worksurface height or
Epicenter
box/file height undersurface storage, bases or end frame
panels to support worksurfaces, privacy screens,
inserts and work tools. Undersurface storage
must be specified without end panel grommets
or back panel option.

The chart below explains how many universal

support brackets or bases are needed for the width
of the Epicenter. When a support base is used, a WaveWorks or Epic
universal bracket will not be needed in that undersurface storage
location. Slat wall insert
supports work tools
Number of Bracket Number of Bracket
Width of Sets Needed for Sets Needed for Epicenter
Epicenter Double Sided Single Sided frame
24" – 48" 2 sets 1 set Worksurface
brackets
54" – 96" 3 sets 2 sets Anywhere along slat wall insert

WORKSURFACE SUPPORT
Any depth or length WaveWorks or Epic
worksurface may be attached perpendicularly
Support pedestal, support
anywhere along the Epicenter slat wall insert when Slat wall base, end panel, or a metal
supported by worksurface brackets (Keeping in insert support base
mind user’s kneespace area).
WaveWorks or Epic
All surfaces must be properly supported at the undersurface storage
opposite end by a support pedestal, support base
or end panel. Undersurface
support rail
REQUIRED SUPPORT
13⁄16" thick; Epicenter Anywhere along top of
Require support every 48". overhead Epicenter frame
19⁄16" thick; storage
Require support every 60".

An undersurface support rail may be specified for

surface spans longer than 48" on 13⁄16" thick
worksurfaces or 60" on 19⁄16" thick worksurfaces.

Consider additional support where heavy loads are

anticipated.

OVERHEAD STORAGE SUPPORT

Any length Epicenter overhead storage may
straddle the top of the Epicenter frame when
properly supported by undersurface storage.
Anywhere along top of
OTHER SUPPORT ISSUES Epicenter trim cap
Because Epicenter may be specified with power
and data capabilities, it will support a power pole
for power entry whip. Power pole must be securely
attached at the ceiling and to the top of the Privacy screen
Epicenter frame.

Epicenter slat wall inserts will support any

combinations of National work tools and one slat
mount monitor arm every 24".

38 National Office Furniture—Specification Guide

 Support and Load

Epicenter Support
(Double Sided, continued)

Epicenter 6" high base

or end panel

Epicenter double depth base

or double depth end panel

Mid support
privacy panel

Epicenter base or
end panel
End support
privacy panel Epicenter 6" high base
or end panel

National Office Furniture—Specification Guide 39

Support and Load

Epicenter Support
(Single Sided)
Epicenter single sided frame must consist of an
Upper
Upper Epicenter and a Lower Epicenter to create
Epicenter
the single sided application. Single sided must be frame
supported on one side by WaveWorks/Epic
worksurface height or box/file height undersurface
storage, bases or end panels to support
worksurfaces, privacy screens, inserts and work
tools. Undersurface storage must be specified
without end panel grommets or back panel
option. WaveWorks or Epic
undersurface storage
The chart below explains how many universal Slat wall insert
support brackets or bases are needed for the width supports work tools
of the Epicenter. When a support base is used, a
universal bracket will not be needed in that
Upper and Lower
location.
Epicenter frame

Number of Bracket Number of Bracket

Width of Sets Needed for Sets Needed for Worksurface
brackets Anywhere along slat wall insert
Epicenter Double Sided Single Sided
24" – 48" 2 sets 1 set
54" – 96" 3 sets 2 sets End trim

Support pedestal, support

WORKSURFACE SUPPORT Slat wall base, end panel, or a metal
Any depth or length WaveWorks or Epic insert support base
worksurface may be attached perpendicularly WaveWorks or Epic
anywhere along the Epicenter slat wall insert when undersurface storage
supported by worksurface brackets (Keeping in
mind user’s kneespace area). Undersurface
support rail
All surfaces must be properly supported at the
opposite end by a support pedestal, support base
or end panel. Epicenter Anywhere along top of
overhead Epicenter frame
REQUIRED SUPPORT storage
13⁄16" thick;
Require support every 48".
19⁄16" thick; End trim
Require support every 60".

An undersurface support rail may be specified for

surface spans longer than 48" on 13⁄16" thick
worksurfaces or 60" on 19⁄16" thick worksurfaces.

Consider additional support where heavy loads are

anticipated.

OVERHEAD STORAGE SUPPORT

Any length Epicenter single sided overhead storage Anywhere along top of
may be mounted to the top of the Epicenter frame Epicenter trim cap
when properly supported by undersurface storage.

OTHER SUPPORT ISSUES

Because Epicenter may be specified with power Privacy screen
and data capabilities, it will support a power pole
for power entry whip. Power pole must be securely
attached at the ceiling and to the top of the
Epicenter frame.

Epicenter slat wall inserts will support any

combinations of National work tools and one slat
mount monitor arm every 24".

40 National Office Furniture—Specification Guide

 Support and Load

Epicenter Support
(Single Sided, continued)

Modesty panel
insert
End trim End cap

Modesty panel
insert Epicenter 6" high base
Epicenter base or or end panel
end panel

Mid support
End trim privacy panel
Modesty panel
insert End support Modesty panel
Undersurface privacy panel insert
storage

National Office Furniture—Specification Guide 41

Support and Load

Renegade Support
Follow these guidelines when planning for Shell Freestanding
Renegade shells.

CONFIGURATION TYPES
Shell
Freestanding
“L” Shaped return or box/file height support
“U” Shaped
“L” Return “L” Box/File

REQUIRED SUPPORT
11⁄8" and 13⁄16" thick.
Require support panel every 48".

Consider additional support where heavy loads

are anticipated.

Surface support is required wherever to surfaces

meet end-to-end. U” Shape

48" maximum

Support
required

13⁄16" thick surface

42 National Office Furniture—Specification Guide

 Support and Load

Renegade Support
Follow these guidelines when planning for
overhead and set-on storage components. WALL REQUIREMENTS WALL MOUNT
STUD WALLS Studs, poured concrete
PROPER SUPPORT Wood studs must be a minimum of 2 x 4’s or concrete block wall
secured to the floor and ceiling.
WALL MOUNTED Maximum height of 14’.
Renegade overhead storage components may be Fasten
attached at desired height directly to load minimum two
METAL STUDS
bearing walls constructed of wood or metal studs, locations
Metal studs must be minimum 20 gauge “C”
poured concrete or concrete block walls with channel secured to the floor and ceiling. Renegade
fasteners appropriate to the wall material. Maximum height of 14’. overhead
storage
Consider mounting height when planning for
adjacent set-on and freestanding storage for POURED CONCRETE AND CONCRETE BLOCK
proper alignment. Attach with appropriate fasteners for wall
material.

STRENGTH
Walls must resist no less than 5 lbs. per square
foot of force applied perpendicular to the wall
and the deflection can not exceed 1⁄240 of the
span for brittle finishes and 1⁄120 of the span for
flexible finishes.

ATTACHMENT
Wall mounted overhead storage must be fastened
directly into studs, poured concrete or concrete
block at a minimum of two locations with
fasteners appropriate for the wall material.

SET-ON OVERHEAD STORAGE/HIGHBACKS

Overhead storage and bookcase units are sized in
6" increments.

All Renegade, WaveWorks and Epic set-on overhead

storage may be used on any properly supported
Renegade shell configuration or credenza.

Consider grommet locations when planning for

set-on overhead storage. Two storage units
side-by-side may interfere with a center grommet
on a worksurface.
Highback units sitting on built-up credenzas with End panel or
support pedestal May straddle bridge or return
20 inch or less deep worksurfaces require support
pedestals. End panels are not acceptable.

PROPER SUPPORT
A shell end panel or support pedestal must be
located under the end panels of the storage unit
for proper support. Undersurface support rails will
not provide proper support.

Match unit width to shell width or be certain an

end panel or support pedestal is located below the
end panel of the storage unit or bookcase.

Side panel of set-on surface storage must be

within 6" of undersurface support/leg.

Set-on surface storage cannot be used in table

desk application.
Undersurface support rails will not provide proper
support for set-on storage. Support panels are
required when the unsupported span is greater
than 48 inches, not an undersurface support rail.

National Office Furniture—Specification Guide 43

 Power and Data

National Office Furniture—Specification Guide 45

Power and Data

Exhibit Power and Data

Exhibit vertical cable manager conceals and
routes task light cords to the integrated wire
managers available on WaveWorks and Epic
worksurfaces. Vertical
cable
manager

Worksurface
wire manager

Multiple below
surface cable
management
options available

WaveWorks, Epic and Renegade

Power and Data
Worksurface wire managers may be specified on
WaveWorks and Epic worksurfaces to route cables
below the surface.

WORKSURFACE CABLE MANAGEMENT

Use any undersurface cable manager to manage Round or
racetrack
cables below the worksurface on WaveWorks, Epic
grommets Vertical wire managers
or Renegade worksurfaces.
are flexible to accommodate
Grommets may be specified for WaveWorks, Epic user needs; used to
or Renegade worksurfaces to route cables conceal power in-feed
through the worksurface. Multiple locations may and data cables
be specified.

All WaveWorks and Epic undersurface storage Surface height

include an optional grommet at the rear, upper power/data access
corner.

Renegade shells include an optional grommet at

the rear, upper corner. Undersurface storage
includes a grommet at the rear, upper corner.

WORKSURFACE POWER AND DATA ACCESS

Multiple undersurface Horizontal wire manager
power/data options used to conceal power
UNDERSURFACE available in-feed and data cables
Convenience outlets, power and
power/communication outlets and Powerlogic
systems may be attached below any WaveWorks
or Epic worksurface to provide access to power
and data.

Cables may be routed through the worksurface

wire manager or surface grommet for access
below the surface.

SURFACE HEIGHT
Power/Data centers, power towers, Byrne
Interlink systems and pivoting power grommets WaveWorks and Renegade Pedestal
may be specified within any WaveWorks or Epic Epic Pedestal Grommet Grommet
worksurface to provide access to power and data
at the surface.

Consider location of support pedestals or other

below surface storage when planning for surface
height power/data components.

46 National Office Furniture—Specification Guide

 Power and Data

WaveWorks, Epic and Renegade

Power and Data (continued) BYRNE INTERLINK SYSTEM EXAMPLES
Surface height
POWERLOGIC INTERCOUPLER SYSTEM power/data access
WAVEWORKS AND EPIC
For private office and open plan applications.
Single circuit system plugs directly into building
power and attaches below worksurface providing
linked power accessed through surface grommets
below. Pedestal
No interlink system
Provides from 2 to 8 outlet modules.

For use with racetrack grommets in WaveWorks To building power

OR...
and Epic.
Surface height
BYRNE INTERLINK SYSTEM power/data access
WAVEWORKS AND EPIC
Bypass jumper
For private office and open plan applications.
Sequential daisy-chain, single circuit system
plugs directly into building power and attaches
through the worksurface providing linked power
accessed at surface height. Pedestal
No interlink system
Provides from 2 to 8 outlet modules.
To building power
For use with racetrack grommets in WaveWorks
and Epic.

BYRNE INTERLINK IQ SYSTEM BYRNE INTERLINK IQ SYSTEM EXAMPLES

WAVEWORKS, EPIC AND RENEGADE
Non-sequential daisy-chain, single circuit system
plugs directly into building power and connects Bypass jumper
to pivoting power grommets within worksurface Bypass jumper
Interlink IQ pivoting
providing linked power accessed at surface
power grommet provides
height. For private office, open plan and training
power/data access
table applications.

Provides from 2 to 8 outlet modules.

For use with G17 cutout in WaveWorks, Epic and

Renegade. To building power

To building power

TABLES

National Office Furniture—Specification Guide 47

Power and Data

Epicenter Power and Data

Upper Epicenter frames can provide 5 wire/
3 circuit, 20 amp power to a linear run of work
spaces. Frames also provide routing for data
cables. Data cable
channel
Access to power and data may be above or below
worksurface height depending on the height of Epicenter
the WaveWorks or Epic undersurface storage it is powered frame
attached to.
Power harness

POWER ENTRY WHIP

Two power entry whips are available. 72" and
144" long.

Power entry whip has a modular connector at

one end, attached to a flexible metal conduit CIRCUIT ARRANGEMENT
with exposed wiring at the other end which is
I II III
hardwired to the building power.

FROM THE FLOOR Hot 1 Black

Power entry whip is hardwired to electrical box
within the floor or to a floor monument. Neutral White

Data cables may also be routed up from the floor Ground Green/Bare
to the data channel at the top of the frame.
Hot 2 Red
FROM THE WALL OR COLUMN
Hot 3 Blue
Power entry whip is hardwired to electrical box
within the wall or column.

Data cables may also be routed up from a wall or Upper Epicenter

column to the data channel at the top of the non-powered
frame. frame
Upper Epicenter Worksurface height
FROM THE CEILING powered frame
Power entry whip is hardwired to electrical box
within the ceiling and routed down through a
power pole attached to the top of the Epicenter
frame. Box/File height Surface height
Data cables may also be routed down through undersurface storage undersurface storage
the power pole to the data channel at the top of
the frame.
Upper Epicenter
CABLE ROUTING non-powered
Power entry whip and data cables are routed up frame
to the frame behind the undersurface storage or Upper Epicenter Worksurface height
down through the power pole. powered frame

HARDWIRE KIT
Hardwire kit can be used with the non-powered
Upper Epicenter frame. Box/File height Surface height
single sided single sided
tackable insert tackable insert

Hardwire kit

48 National Office Furniture—Specification Guide

 Power and Data

Epicenter Power and Data

(continued) Power
harness Power direction
CONNECTION

POWER ENTRY WHIP

The power entry whip 3-way connector plugs into
the power harness within any Epicenter powered
divider frame. Power entry whip may connect at
the end of a run or anywhere within the run, Power entry whip
providing power in one or both directions. from the floor
Power pole
JUMPER
Power direction
The jumper plugs into the power harness within
one Epicenter powered divider frame and plugs
into the next Epicenter powered divider frame to
continue power along the run.

BYPASS JUMPER
The bypass jumper plugs into the power harness
within one Epicenter powered divider frame, Power entry whip from wall Power entry whip from
passes through a non-powered divider frame or or column the ceiling
below a freestanding component and plugs into
the next powered frame to continue power along
the run.

EPICENTER POWER AND DATA

ACCESS
Duplex receptacles plug into one or both sides of
the power harness within the Epicenter powered
frame. Jumper Bypass jumper Bypass jumper
Receptacles are labeled as to the specific circuit through Epicenter beneath storage
they are connected to. I, II, and III.

30" through 72" accept 2 per side. 24" accepts

1 per side.

INSERT CUTOUT OPTIONS No cutouts

Tack board and slat/tack board inserts are
available with multiple cutout options. Power harness
Cutouts are always located 9" in from the left
and right end of the insert, with the exception Duplex Receptacle
of 24" which has a single cutout on center. cutouts
Cutouts accommodate 1 duplex receptacle or
1 duplex receptacle and 2 blank data ports.
Receptacle left,
Appropriate faceplates are shipped with the receptacle/data
inserts. Power Receptacle
right
Duplex Faceplate
INSERT CUTOUT CONFIGURATIONS
III Circuit label Receptacle right,
• No cutouts
Duplex receptacle/data
• 2 power receptacles
• 1 power receptacle left, 1 power/data left
Power/Data Receptacle
receptacle right
• 1 power receptacle right, 1 power/data
receptacle left III Duplex Receptacle/data
• 2 power/data receptacles cutouts
Duplex/Data Faceplate
Data ports

National Office Furniture—Specification Guide 49

 Product Specification

National Office Furniture—Specification Guide 51

Product Specification–Exhibit

Exhibit Wall Rails

BASICS Use one rail, any length
Attach to fixed walls to support WaveWorks and WaveWorks or Epic
Epic worksurfaces, WaveWorks and Epic overhead overhead storage
storage and Exhibit inserts.
Upper
Included based on model ordered: rail
• 1 or 2 rails
• Splice plates for rail alignment Faceplate
• 1 or 2 faceplates to conceal fasteners and
splice plates and secure inserts
• 72" or 144" long. May be field cut to Filler strip
length required

Lower
REQUIRED
rail
Appropriate fasteners for wall material. Supplied
by installer. Faceplate

SPECIFICATION TIPS
Minimum rail length is 18". There is no maximum
length requirements for Exhibit rail runs.

Use one rail, with or without faceplate for WaveWorks or Epic

overhead storage
supporting worksurfaces or overhead storage.

When mounting overheads, rail must equal or be Exhibit inserts

greater than the width of overheads being
mounted.
WaveWorks or Epic
Use 2 rails and faceplates when supporting worksurface
inserts.

Rails can mount at any height when supporting

inserts with overheads only.

Specify insert heights based on adjacent

component heights; see diagram below.

WORKS WITH
• Worksurface mounting brackets for
WaveWorks and Epic worksurfaces
• WaveWorks and Epic overhead storage
• Exhibit slat wall, tack board, marker board,
organizer shelf and slat wall/tack inserts
with trim channels
• Full end trim
• Single rail end caps

52 National Office Furniture—Specification Guide

 Product Specification–Exhibit

STANDARD HEIGHTS

661⁄16" 66½" 777⁄8" 785⁄16"

63¾"

28½" 28½" 28½" 28½" 28½"

34" high inserts. Matches 36" high inserts. Matches 37" high inserts. Matches 48" high inserts. Matches 49" high inserts. Matches
66" high vertical storage. 68" high vertical storage. 69" high vertical storage. 79" high vertical storage. 80" high vertical storage.
Also standard height for
conference, training rooms
and common areas.

COUNTER HEIGHTS

723⁄8" 7213⁄16" 843⁄16" 845⁄8"

701⁄16"

3413⁄16" 3413⁄16" 3413⁄16" 3413⁄16" 3413⁄16"

34" high inserts. 36" high inserts. 37" high inserts. 48" high inserts. 49" high inserts.

BAR HEIGHTS

7811⁄16" 791⁄8" 90½" 9015⁄16"

763⁄8"

411⁄8" 411⁄8" 411⁄8" 411⁄8" 411⁄8"

34" high inserts. 36" high inserts. 37" high inserts. 48" high inserts. 49" high inserts.

National Office Furniture—Specification Guide 53

Product Specification–Exhibit

Inserts
BASICS Tack board Marker board
Tack board, marker board, organizer shelf, slat 18"-60" wide 24"-60" wide
wall and slat/tack wall inserts attach within 34", 36", 37", 34", 36", 37",
Upper 48", 49" high 48", 49" high
Exhibit upper and lower rails with faceplates.
rail
• 2 trim channels each (provided with insert)
• 18" to 60" wide. Tack boards and HPL Faceplate
marker boards may be scribed in the field
• 5 heights available on all inserts
Insert
REQUIRED
Exhibit upper and lower rails with faceplates. Slat wall Slat/Tack wall
Lower 24"-48" wide 24"-48" wide
Additional trim channels may be ordered for rail 34", 36", 37", 34", 36", 37",
inserts scribed in the field. Faceplate 48", 49" high 48", 49" high
Full end trim for inserts at the end of a run Tack
when end is exposed.

23" standard Slat

SPECIFICATION TIPS
Inserts may be used in rails at any desired
height.
Organizer shelf
Specify insert height based on adjacent 36"-60" wide
component heights. 34", 36", 37",
48", 49" high
For the best aesthetics, specify insert widths to
match overhead storage and/or worksurface
width or depth. Knife rim on worksurface adds
1½" per side to worksurface depth. Specify insert
1 size wider than worksurface depth and field
scribe to match.

FYI
Porcelain marker boards, organizer shelf and slat
wall inserts may not be field scribed.

It is not required that inserts be placed behind

freestanding storage when wall rails pass behind.

WORKS WITH Exhibit inserts

• Vertical cable manager
• Slat wall and slat/tack wall accepts
accessories and work tools anywhere along Trim channel
the slat insert.
Adjacent storage

Accessories and work tools

Full end trim

54 National Office Furniture—Specification Guide

 Product Specification–Exhibit

Worksurface Mounting Brackets

BASICS
Attach anywhere along the Exhibit lower rail to
support worksurfaces. Mounting brackets

REQUIRED
• Exhibit lower rails. Anywhere
• Support pedestal, support base, end panel,
metal support base and/or a undersurface
support rail.
Perpendicular

FYI
Wall rail faceplates are only required when
inserts are used. Lower rail
Worksurface
SPECIFICATION TIPS mounting
Worksurfaces may attach linear or perpendicular brackets
to the lower rail.
• For worksurfaces up to 48" use 2 brackets
• For worksurfaces up to 72" use 3 brackets
• For worksurfaces greater than 72" use Linear
4 brackets

WORKS WITH
WaveWorks or Epic worksurfaces.

National Office Furniture—Specification Guide 55

Product Specification–Exhibit

Work Tools and Trim

Work Tools Monitor Arms WORKS WITH
Vertical cable manager.
BASICS BASICS
Work tools attach anywhere along the slat wall Must properly install slat wall when using a
or slat/tack wall inserts attached within Exhibit monitor arm.
upper and lower rails with faceplates.
Recommended to not use monitor arm on the
upper four slats of a full slat wall and slat wall
REQUIRED Trim channel
combo insert.
Slat wall or slat/tack wall inserts within Exhibit
upper and lower wall rails with faceplates.
SPECIFICATION TIPS Insert
Weight capacity 13 lbs.
SPECIFICATION TIPS
Consider quantity and types of work tools based One monitor arm every 24" on slat wall and only
on size of slat wall or slat/tack wall insert. one monitor arm recommended for a slat/tack
combo insert.
Consider clearance at worksurface and below
overhead storage for access to work tools and
contents.

Monitor arms are not recommended to use with

Vertical Cable Manager
slat inserts.
BASICS
Vertical cable manager attaches to the trim
channel to conceal and route task light cords.

Attach anywhere Single End Cap

BASICS Trim
Single end cap finishes the end of a single upper channel
or lower wall rail.
Vertical
cable
SPECIFICATION TIPS manager
Use at the end of an upper or lower wall rail
Clearance
where no inserts are used.
above
Clearance
below

Single end cap

Filler Strips
Full End Trim
BASICS
BASICS Filler strips are required between the wall and
End trim finishes the full height end of a run of Exhibit mounted overhead storage to provide
wall rails, faceplates and inserts when end is proper support where no inserts are used.
exposed.
WORKS WITH
SPECIFICATION TIPS WaveWorks and Epic overhead storage.
End trim is 3" higher than insert height. Specify Trim Channels
height to match insert and wall rail combined
height. BASICS
Fabric or painted trim channels finish the space Filler strips
between inserts. 2 trim channels standard with
End trim
inserts.

Insert SPECIFICATION TIPS

Match trim channel height to insert height.
Match trim channel to insert finish or material or
Wall rail and mix finish or materials to create vertical
faceplate patterns.

Specify additional trim channels for all field

scribed inserts.

56 National Office Furniture—Specification Guide

 Product Specification–WaveWorks and Epic

Worksurfaces
BASICS
Worksurfaces, cornice tops and Epicenter depth Worksurfaces
worksurfaces may be used to create private
office, open plan and table desk configurations.

Worksurfaces may be applied to undersurface

storage and lateral files to create credenzas or
desks.

Component worksurfaces may also be used to

expand assembled configurations.

Modified worksurface sizing is available. See

price list for models available.
Epicenter depth worksurfaces
9 rim options available on WaveWorks.
Cornice tops
2 rim options available on Epic.

Includes appropriate attachment hardware when

specified.

WaveWorks Worksurfaces
• 13⁄16" or 19⁄16" thick
• 18" deep: 30" to 96" wide in 6" increments
• 24" deep: 30" to 96" wide in 6" increments Box/File height undersurface storage without
• 30" deep: 48" to 96" wide in 6" increments the end panel grommet or back panel option
• 36" deep: 60" to 84" wide
Credenzas Tables
Epic Worksurfaces
• 13⁄16" thick
• 18" deep: 30" to 96" wide in 6" increments
• 24" deep: 30" to 96" wide in 6" increments
• 30" deep: 48" to 96" wide in 6" increments
• 36" deep: 60" to 84" wide
Any combination of
undersurface storage may be
Epicenter Depth Worksurfaces used to create a credenza
• 227⁄16" and 285⁄8" deep. 30" to 96" wide
in 6" increments

Cornice Tops
• 13⁄16" or 19⁄16" thick 1 side 1 or 2 sides 1 or 2 sides
• 15" deep: 18", 30" to 108" wide in
Worksurface
6" increments
wire manager
• 24" deep: 18" and 36" wide
Back only
Worksurfaces Wire Managers Left only
A selection of worksurfaces are available with Right only Left only
optional wire managers on 1 end only or 1 or Back and left Right only
2 sides. Surface grommets may be located left or Back and right Left and right
right side and on center back. Use worksurface
wire manager fillers to cap off exposed ends of
wire managers.

National Office Furniture—Specification Guide 57

Product Specification–WaveWorks and Epic

Worksurfaces 24", 30" and

36" deep Freestanding and “L” configuration Linear or peninsula “U” configuration
table desks “T” configuration
REQUIRED
Exhibit lower wall rails and worksurface
mounting brackets, support panels, support
pedestals or undersurface storage components.

SPECIFICATION TIPS
Properly supported, worksurfaces may be used in
any desired length to create freestanding, table
desk, linear, peninsula,“L”, “T” and “U”
configurations.
M
By specifying M, E or F in the model number, all
E E M
worksurfaces arrive with the appropriate
bracketry for installation. M
F
M = Main E E E
E = Extension
M
F = Filler

M = 0 Connecting Flat Brackets

E = 2 Connecting Flat Brackets
F = 4 Connecting Flat Brackets

Worksurfaces may be configured at box/file

Worksurface
height combined with worksurface height using height
box/file height and worksurface height Anywhere
undersurface storage and supports.

For 6" guest side overhang, use 30" deep

worksurface with 24" undersurface storage or
36" deep worksurface with 30" undersurface
storage. Box/File height Or...

WORKS WITH
• Powerlogic Intercoupler system 30" or 36" deep
• Byrne Interlink and Interlink IQ electrical worksurface
systems
6" overhang
• Worksurface grommets
• Worksurface wire managers 24" or 30" deep
• Undersurface cable management undersurface storage or
components support
• Set-on overhead storage
• Privacy screens and modesty panels
• Center drawers, keyboard trays, CPU holders
and monitor arms
Worksurface
FYI wire manager
Knife rim adds 1½" per side to worksurface No worksurface
depth. Knife rim is not recommended on lower wire manager
storage as it affects user’s kneespace. Knife rim
or use filler cap
adds 1½"
Consider where you specify a worksurface with per side
Worksurface wire manager. When attached to
Exhibit lower wall rail, do not use at the end of
run for a cleaner aesthetic, or cap off exposed
end with a filler cap.

58 National Office Furniture—Specification Guide

 Product Specification–WaveWorks and Epic

Worksurfaces 18" deep

REQUIRED 18" worksurface
Metal lateral file and hinged door units. Any metal lateral file
and hinged door units
SPECIFICATION TIPS
Use to finish top of metal lateral file and hinged
door units.

18" surfaces are ideal for training tables.

Cornice tops 15" deep

15" deep tops to finish the top of highback
organizers, Exhibit or wall mount overhead
storage units or bookcases.

REQUIRED
Highback organizers, Exhibit or wall mount
overhead storage units, bookcases, or vertical
storage units.

SPECIFICATION TIPS
Specify rim option to match or contrast
worksurface rim.

May be used to span 2 units. Specify model with

finished bottom.

Epicenter Depth Surfaces

Epic worksurfaces are sized to finish the top of
undersurface storage in Epicenter work spaces.

WaveWorks worksurfaces must be specified at a

modified depth of 227⁄16" and 285⁄8 to align with
the Epicenter.
Worksurface
wire manager
REQUIRED
Undersurface storage

SPECIFICATION TIPS
Use to finish the top of box/file or worksurface
height undersurface storage. When using Box/File height undersurface storage without Worksurface height undersurface storage
WaveWorks worksurface specify 13⁄16" thick the end panel grommet or back panel option without the end panel grommet or back panel option
worksurface.

Single worksurface may span multiple

undersurface storage units.

Match worksurface width to total length of

undersurface storage.

Worksurfaces are available with wire managers.

Specify on back edge only.

WORKS WITH
• Worksurface grommets
• Worksurface wire managers
• Undersurface cable management
components

National Office Furniture—Specification Guide 59

Product Specification–WaveWorks and Epic

Tables
Worksurfaces may be used to create leg-based table
applications.

Bases available in worksurface height, counter Column legs

height, bar height and height adjustable. with or without
Square or round dual wheel
All static bases have adjustable glides with a
support bases locking casters
1½" range.

Mobile bases have dual wheel locking casters.

Bases include appropriate attachment hardware.

REQUIRED FOR PENINSULA CONFIGURATIONS

Square or round support base, column leg, wood half
round support base, “H” or “U” style support base,
“C” or “T” leg or 4-star base.

REQUIRED SUPPORT T-legs C-legs

4-star bases
13⁄16" thick;
Require support every 48".
19⁄16" thick;
Require support every 60".

Undersurface support rail available to support

surfaces up to 72".

Consider additional support where heavy loads are

anticipated. “H” or ”U” style
support bases Disc bases
Surface support is required wherever 2 surfaces meet
end-to-end.

In place of end panels, corner surfaces may be

supported by a support base at the back corner when
connected to an adjacent surface.

SPECIFICATION TIPS
Tables may be used in private office, extensions to “U” style bar or counter
“H” style bar or counter
open plan environments, conference and training height support bases
height support bases
areas.

Use mobile tables in collaborative environments as

shared worksurfaces.

Tables may be combined in multiple configuration for

conference and training areas.

FYI
Maximum span between legs on 13⁄16" thick
worksurface is 48". Maximum span between legs on Manual Hand Crank Adjustable Height Bases Electrically Adjustable Height Bases
19⁄16" thick worksurface is 60".

Support base “H” and “U” Style may be used with all
worksurfaces except “U” and “P” shape.

WORKS WITH
• Powerlogic Intercoupler system
• Byrne Interlink and Interlink IQ electrical
systems
• Worksurface grommets
• Undersurface cable management components Manual Hand Crank Adjustable Height L Top Bases Electrically Adjustable Height L Top Bases
• Privacy screens and mesh, resin and metal
modesty panels
• Center drawers, keyboard trays and monitor
arms

60 National Office Furniture—Specification Guide

 Product Specification–WaveWorks and Epic
Worksurface Support
BASICS
A selection of worksurface supports and bases
are available to create desking configurations
and tables to fit most desired aesthetics.

All static supports and bases have adjustable

glides with a 1½" range.

Mobile bases have dual wheel locking casters. “H” Style or “U” Style Square or round
support base support base
Bases include appropriate attachment hardware.

Supports
• 12", 24", 30" and 36" deep
• Worksurface and box/file heights

Bases
• Worksurface, counter, bar height and height
Square or round
adjustable.
support base

SPECIFICATION TIPS
For an open aesthetic use “U” Style or “H” Style
support bases.
Box/File end
For stronger look and where consistent finishes support
are desired, use undersurface storage
components and end panels.
Undersurface support
Surface heights may be varied by using box/file and end panels
height end panels.

Recommended work surface length of 84" on

angled top when using lower height storage to
allow for sufficient kneespace.

Bar height Counter height

Modesty and Back Panels

BASICS
Modesty panels may be applied to all component
worksurfaces, tables and undersurface storage Full overlay Full overlay
Single or double pedestal Pedestal or lateral files
components to finish the back or create
kneespace on approach side.

Modesty panels are non-structural and provide

privacy/aesthetics.

Back panels may be applied to all undersurface

storage components to finish the back. Provides access
to power and
Includes appropriate attachment hardware. data at the
Worksurface height or 1/3 height wall
Modesty Panels box/file height
• Full overlay in 28" worksurface height and
22" box/file height.
• 1/3 height in 8" and 13" heights.

Back Panels
• In 28" worksurface height and 22" box/file
height. Inset on guest side
Rectangular
REQUIRED
Worksurface, table, pedestal or lateral file.
1/3 height Worksurface height or
box/file height
National Office Furniture—Specification Guide 61
Product Specification–WaveWorks and Epic

SPECIFICATION TIPS
Modesty Panels
Modesty panels may be inset to provide guest
side knee space.

Full overlay. Specify modesty panel to match

worksurface width.
Tapered
Consider worksurface and undersurface storage
component height and widths as well as support
Support base or end panel
locations when specifying modesty panel widths.

By specifying, M, E or F in the model number, all Undersurface storage

modesty panels arrive with the appropriate
bracketry for installation.

M = Main E = Extension F = Filler

Full Height
M = 0 Brackets
E = 1 Return Mounting Bracket
F = 2 Return Mounting Brackets
Main Modesty Panel Back Panel Extension Modesty Panel Filler Modesty Panel
1/3 Height
M = 2 L-Brackets
E = 1 L-Bracket/1 Return Mounting Bracket
F = 2 Return Mounting Brackets

Main Modesty Panels

• Specify modesty panel as MAIN when using
as a full modesty or back panel
• Specify back panel to match pedestal
height and width.

Filler Modesty Panels

• Specify modesty panel as FILLER when
attaching to two component end panels
Main 1/3 Height Modesty Panels
Extension Modesty Panels
• Specify modesty panel as EXTENSION when
attaching to one component side

Main 1/3 Height Modesty Panels

• Specify 1/3 height modesty panel as
MAIN when attaching between two
pedestals, a pedestal and end panel or
two end panels Filler 1/3 Height Modesty Panel

Filler 1/3 Height Modesty Panels

• Specify 1/3 height modesty panel as
FILLER when attaching to two end panels

Extension 1/3 Height Modesty Panels

• Specify 1/3 height modesty panel as
EXTENSION when attaching to a pedestal
and end panel or end panel to end panel Extension 1/3 Height Modesty Panel
1/3 height. Specify modesty panel to match
worksurface width minus width of undersurface
storage components.

FYI
Glass top desk accepts modesty panel between
pedestals only.

62 National Office Furniture—Specification Guide

 Product Specification–WaveWorks and Epic

Privacy Screens
BASICS
Privacy screens are freestanding and can be set Rectangular
on component worksurfaces, tables and
undersurface storage worksurfaces to add seated
Tapered
privacy.

Includes appropriate hardware.

Privacy Screens Set-On Surface

• Acrylic tapered or rectangular and felt
rectangular
• 18" high.
• 21", 24", 27", 30", 36", 42", 48", 54", 60" Rectangular
and 72" wide.

Privacy Screens Edge Mount Modesty/Privacy

• Rectangular
• 32" high.
• 21", 24", 27", 30", 36", 42", 48", 54", 60"
and 72" wide.

Privacy Screens Edge Mount Privacy

• Rectangular or tapered
• 20" high.
• 21", 24", 27", 30", 36", 42", 48", 54", 60"
and 72" wide.

SPECIFICATION TIPS
May be used to provide degree of enclosure or to
define personal space. Edge mount Edge mount
modesty/privacy screen privacy screen
Placed on box/file height storage and on
worksurface to create a layered division of space.
Mix tapered and rectangular to vary the
aesthetic.

Consider worksurface width and location of

adjacent or overhead storage when specifying Tapered privacy
length. screen Epicenter
mount
Multiple screen lengths may be used along a run
to vary the look.

Mid support
privacy panel

End support
privacy panel

National Office Furniture—Specification Guide 63

Product Specification–WaveWorks and Epic

Storage
BASICS
Overhead storage components are available as
wall mounted or Exhibit mounted. Additional
storage components can be freestanding, set-on
surface or used as undersurface storage.

All undersurface and freestanding components

have adjustable glides with a 1½" range.

Wall mount and set-on components include

appropriate attachment hardware.

Exhibit mount cabinets include appropriate

attachment hardware but wall rails must be
ordered separately.

Multiple pull options are available.

TYPES
Undersurface Storage Undersurface Storage Set-On Storage
Worksurface height
• File/file and box/box/file pedestals.
• Lateral files, double door units, bookcase,
mixed storage and multi-file cabinets.
Box/file height
• Box/file pedestals.
• Box/file mobile pedestals.
• Lateral files, and bookcases.

Set-On Storage
• Highback organizers with or without doors.
• Corner highback organizers with or without
doors.
• Bookcases.
Exhibit or Wall Mount Overhead Storage
• Bookcase with doors.
• Storage module shelf.

Exhibit Wall Rail or Wall Mount

• Overhead storage cabinets with or without
doors.

Freestanding Storage
• Mobile pedestals.
• 2, 3, 4 and 5 drawer lateral files with
13⁄16" or 19⁄16" top.
• Multi-file and mixed storage cabinet. with
13⁄16" or 19⁄16" top.
• Storage towers and wardrobe/storage
cabinets doors, drawers and bookcases.
• Bookcases. Freestanding Storage
• Bookcases with doors.
90 degree
bookcase option
available

64 National Office Furniture—Specification Guide

 Product Specification–WaveWorks and Epic

Storage (continued)
REQUIRED
Worksurface for undersurface component storage.

Ganging brackets for Exhibit mounted, wall Specify ganging plates for
mounted overhead storage or runs of each joint to create a clean,
freestanding components. straight run

SPECIFICATION TIPS
Use Exhibit or wall mount overhead to utilize
wall space in private office and collaborative
environments around the perimeter space.
Accepts tack
Set-on storage may be used to create work space board
privacy when placed back to back. Consider
Back-to-back
location of worksurface grommets when selecting for maximum
overhead storage. privacy
Consider freestanding storage components
heights when used adjacent to Exhibit wall rail
or wall mounted overhead storage.

Overhead stanchions are specified as “U”

(defacing) stanchions or “O” (non-defacing)
stanchions.
“U” stanchions must be mounted to the
worksurface (defacing).
“O” stanchions are attached to the worksurface
with double sided tape (non-defacing).

Multiple undersurface storage components may

be placed under a common worksurface within a Support panel
workspace. Specify combined undersurface
storage component widths and depths to match
End or support panel
worksurface.

Add a cushion to undersurface top or use a

mobile pedestal with a cushion top for additional
seating.

Multiple 3 drawer lateral files may be ganged Specify height to match

together under a common worksurface to create
a counter height workcenter.
Vary the height of long runs of freestanding
storage to compensate for uneven floors, while
providing visual interest.
Add a cushion
Undersurface storage
WORKS WITH
components with a single
• Full overlay modesty panels for pedestals
common worksurface top
and lateral files
• Worksurface for undersurface storage
• Task lights for highback organizers, Exhibit Common worksurface top
or wall mount overhead storage
• Interior drawer accessories for box, file and
lateral file drawers Creates a workcenter
• Interior accessories for open storage
• Storage surface cushion
• Tack board
Vary component height

National Office Furniture—Specification Guide 65

Product Specification–Epicenter

Undersurface Storage
(Double and Single Sided)
BASICS Use any width and combination of undersurface FYI
Epic or WaveWorks worksurface or box/file height components on either side to create small Specify undersurface storage without the end
undersurface storage components are placed back-to-back or long runs of multiple work panel grommet or back panel option.
back-to-back to create the infrastructure of spaces.
Epicenter work spaces. WaveWorks worksurfaces must be specified with a
Worksurfaces are not dependent upon the modified depth of 227⁄16" or 285⁄8" to align with
Undersurface storage supports the Epicenter undersurface component widths used as long as the Epicenter.
frame dividers in any length run. the combined total widths are equal. Specify any
length worksurface available to finish the tops of WORKS WITH
Undersurface storage components have
the undersurface storage. • Epic or WaveWorks worksurfaces
adjustable glides with a 1½" range.
Epicenter divider and insert lengths are not • Epicenter dividers
Multiple pull options are available. • Interior drawer accessories for box, file and
dependent on the undersurface component
widths, as long as the combined widths are equal lateral file drawers
TYPES to the total width of the undersurface • Storage surface cushion
Worksurface Height components. Consider desired location of inserts
• File/file and box/box/file pedestals. and power/data locations when planning for run
23" and 29" deep length.
• Lateral files, double door units, bookcase,
mixed storage, project drawer and Consider the degree of privacy desired.
multi-file cabinets. 23" deep. 24", 30" and 7" of divider height may be gained by using
36" wide worksurface height versus box/file height
undersurface storage.
Box/File Height Freestanding storage or components with set-on
• Box/file pedestals. 23" deep storage may be used between runs to create
• Lateral files, box/lateral files, bookcases, additional work space privacy and visual interest.
project drawer and double door units. 23"
deep. 24", 30" and 36" wide
Small work spaces 7" higher than box/file height
REQUIRED
Epic or WaveWorks worksurfaces.

Epicenter end trim.

SPECIFICATION TIPS
Epic or WaveWorks worksurface storage
components are used to create any length
run of collaborative work spaces. Due to the
base styles unique to Epic and WaveWorks,
it is recommended that one style be used Worksurface height undersurface storage
consistently within a run. without the end panel grommet or back panel option

Multiple runs of work spaces Multiple runs of work spaces

Any combination of
Any combination
divider lengths
of divider lengths

End trim

Box/file height undersurface storage without

Box/file height undersurface storage without the end panel grommet or back panel option
the end panel grommet or back panel option
66 National Office Furniture—Specification Guide
 Product Specification–Epicenter

Epicenter
(Double and Single Sided)
Non-powered Epicenter Dividers Inserts are not dependent upon the frame length
BASICS Non-powered dividers may be used as a support and may be placed off module with the
Epicenter dividers are a series of powered and for perpendicular worksurfaces, privacy screens exception of where power data must be accessed.
non-powered frames that are supported by Epic and work tools. Specify slat wall inserts wherever Specify inserts with power/data cutouts to match
and WaveWorks worksurface height and box/file worksurfaces and work tools will be placed. divider length to align cutouts to receptacles.
height undersurface storage, bases or end
panels. Powered Epicenter Dividers WORKS WITH
Powered dividers provide power/data capabilities • Power entry whip, jumpers and bypass
TYPES anywhere along the run and also support jumpers
Upper Epicenter perpendicular worksurfaces, privacy screens and • Epicenter end trim and trim caps
Powered work tools wherever slat wall inserts are specified. • Tack board, marker board, slat wall and
• Frame with power harness. 13" high. slat/tack board
Receptacles are specified separately.
24"-72" in 6" increments. 24" provides • Privacy screen
1 power/data location per side. 30"-72" • Work tools
FYI
provide 2 per side
When a privacy screen is used above a divider,
Non-powered
an Epicenter trim cap is required.
• Frame only. 13" high. 24"-96" in
6" increments
Data cable
Lower Epicenter channel
Non-powered (only) Epicenter
• Frame only. 22" (box/file height) and powered frame
28" (worksurface height) high. 24"-96" in
6" increments Power harness
• Must be specified in same width as Upper
Epicenter

REQUIRED
Epic or WaveWorks back-to-back undersurface
storage, bases or end panels for double sided. Powered Epicenter
Upper and Lower Epicenter for single sided Power/Data access
application. above the worksurface

Undersurface storage, bases or end panels and a

worksurface must be used on one side of the Non-powered Epicenter
single sided Epicenter.

Universal attachment brackets.

Tack board, marker board, slat wall and slat/tack

board inserts.

The chart below explains how many universal Worksurface height undersurface storage
support brackets or bases are needed for the without the end panel grommet or back panel option
width of the Epicenter. When a support base is
used, a universal bracket will not be needed in
that location.
Width of Epicenter Number of Brackets/Bases
24" – 48" 2
54" – 66" 4 Any combination of
72" – 96" 6 divider lengths
Power/Data access
SPECIFICATION TIPS below the worksurface
Epicenters may be used in any combination of
lengths along the run.

Epicenter divider lengths are not dependent on

the undersurface component widths, as long as
the combined widths are equal to the total
width of the run.

Consider desired location of power/data access

when planning for location of powered and
non-powered dividers.
Box/File height undersurface storage without
the end panel grommet or back panel option

National Office Furniture—Specification Guide 67

Product Specification–Epicenter

Epicenter
(Double and Single Sided, continued)

Powered Epicenter
Power/Data access
above the worksurface

Non-powered Epicenter

Worksurface height undersurface

Modesty panel storage without the end panel
insert grommet or back panel option
End trim

Divider trim cap required

Any combination of
divider lengths
Power/Data access
below the worksurface

End trim

Upper and
Lower Epicenter Box/File height undersurface storage without
the end panel grommet or back panel option

68 National Office Furniture—Specification Guide

 Product Specification–Epicenter

Epicenter Dividers
Power and Data Power pole

BASICS Power direction

Epicenter powered dividers contain a power
harness within the frame to provide
3 circuit/5 wire, 20 amp power to a linear run
of workstations and a top channel for routing
data cables.

Power harness is pre-installed within the divider

frame. Power entry whip from floor, wall or column Power entry whip from the ceiling

TYPE
• Frame with power harness. 13" high.
24"-72" in 6" increments. 24" provides
1 power/data location per side. 30"-72"
provide 2 per side

REQUIRED
Power entry whip Jumper Bypass jumper
Power pole for ceiling access to building through Epicenter
power jumper
Bypass jumper
Receptacle or power/data receptacle Data cables route through top channel
Tack board or slat/tack board inserts

SPECIFICATION TIPS
Power entry whip
Specify power entry whip to bring power to the Duplex receptacle
power harness. Power entry may be located
anywhere along the run and will provide power
to all connected harness’s in either direction.

Plan for power entry whip to be located as close

to building power as possible.
Power/Data Receptacle
Power pole Power Receptacle
Specify a power pole to if closest building power
Duplex Faceplate III Duplex
is in the ceiling.
III Circuit label Duplex/Data Faceplate
Power entry whip must be specified separately.
Duplex .59" (15 mm) Data ports
Jumper
Power is continued from divider to divider by .76" (19.5 mm)
specifying an 18" jumper for each divider
connection. Bypass Jumper Applicability
Epicenter with
Epicenter Bypass Epicenter with box/file
Model worksurface height
Bypass jumper Jumpers height pedestals
pedestals
Power and data may pass through a non-powered 25N42ELJ 24" Epicenter - -
25N48ELJ 30" Epicenter - -
divider or below freestanding storage by
25N54ELJ 36" Epicenter - -
specifying a bypass jumper. 25N60ELJ 42" Epicenter - -
25N66ELJ 48" Epicenter - -
25N72ELJ 54" Epicenter - -
Receptacles 25N78ELJ 60" Epicenter - -
Receptacles plug directly into the power harness 25N84ELJ 66" Epicenter 1 - 18" W Vertical -
within the Epicenter divider frame. Storage Cabinet
25N90ELJ 72" Epicenter 1 - 24" W Storage -
Specify duplex receptacles for each cutout in Cabinet
25N96ELJ 78" Epicenter 1 - 30" W Vertical 1 - 18" W Vertical
tack board or slat/tack board inserts specified. Storage Cabinet Storage Cabinet
Faceplates will be specified when specifying 25N102ELJ 84" Epicenter 1 - 36" W Vertical 1 - 24" W Vertical
inserts. Storage Cabinet Storage Cabinet
- 2 - 18" W Vertical -
Storage Cabinets
Receptacles are labeled as to the specific circuit 1 - 30" W Vertical
25N108ELJ 90" Epicenter -
they are connected to. I, II, and III. Storage Cabinet
25N114ELJ 96" Epicenter 2 - 24" W Vertical 1 - 36" W Vertical
Specify receptacles based on the device to be Storage Cabinets Storage Cabinet
connected. For example, computers should be on - - 2 - 18" W Vertical
Storage Cabinets
a separate circuit than lighting or other devices 2 - 24" W Vertical
25N126ELJ - -
that may require a greater load. Storage Cabinets

National Office Furniture—Specification Guide 69

Product Specification–Epicenter

Inserts Cutouts are always located 9" in from the left • 1 power receptacle left, 1 power/data
and right end of the insert, with the exception receptacle right
of 24" which has a single cutout on center. • 1 power receptacle right, 1 power/data
BASICS
receptacle left
Inserts attach to Epicenter dividers to finish the Cutouts accommodate 1 duplex receptacle or • 2 power/data receptacles
frame, provide and support work tools, support 1 duplex receptacle and 2 blank data ports.
worksurfaces, receptacles and power/data
receptacles. WORKS WITH
INSERT CUTOUT CONFIGURATIONS • Receptacles and power/data receptacles
Marker board, slat wall and slat/tack inserts • No cutouts • Work tools
include two trim channels. • 2 power receptacles

If tack board or slat/tack board is specified with Slat wall insert

power/data cutouts, they include appropriate
faceplates.

Appropriate attachment hardware included.

TYPES
Tack board, marker board, slat wall and slat/tack
board for Upper Epicenter
• 11" high. 24"-72" in 6" increments

Tack board, laminate, and veneer for single

sided Epicenter
Slat/Tack board insert
• 39" (worksurface height) high. 24"-72" in
with or without cutouts
6" increments
• 32" (box/file height) high. 24"-72" in
Slat/Tack board insert
6" increments with or without cutouts
Veneer and laminate modesty panel inserts
• 26" (worksurface height) high. 24"-72" in Power receptacle left,
6" increments. Modified sizing available No cutouts power/data receptacle
right
• 19" (box/file height) high. 24"-72" in
6" increments. Modified sizing available
Receptacle right,
REQUIRED Power receptacle power/data receptacle
Upper Epicenter divider frame for double cutouts left
sided application

Upper and Lower Epicenter divider frame for

single sided application Power/data
receptacle cutouts
SPECIFICATION TIPS
Inserts are not dependent upon the frame length
and may be placed off module with the exception
of where power data must be accessed. Specify
tack board and slat/tack board inserts with
power/data cutouts to match divider length.
Work tools
Upper inserts are needed for a double sided
Upper Epicenter application or on the user side
of a single sided application.

Single sided inserts are needed for a single sided

application on the approach side.

Modesty panel insert sizing must be specified

after the undersurface storage or Epicenter
supports are specified. Modesty panel inserts will
run between undersurface storage and end
support panels. Modesty panel inserts run behind
Epicenter support bases. Modified sizing
available.

Work tools are available to attach anywhere

along the slat insert. Epicenter modesty
panel insert available
INSERT CUTOUT OPTIONS in modified sizing
Tack board and slat/tack board inserts are
available with multiple cutout options.

70 National Office Furniture—Specification Guide

 Product Specification–Epicenter

Overhead Storage
BASICS
Epicenter overhead storage straddles the
Epicenter divider and provides an increased
degree of privacy. Because overhead supports
rest on the worksurface, they may be placed in
line with or extend beyond the divider.
Individual Shared
Sliding door models feature a facemount
powder coated aluminum track along top and
bottom of cabinet.

TYPES
Shared:
1 open shelf or sliding door on each side. Anywhere along the run

Individual:
2 open shelves or sliding doors on 1 side.
• 14" high. 15" deep. 30", 36", 42", 48" and
60" wide

Single sided:
2 open shelves or sliding doors on 1 side.
• 14" high. 15" deep. 30", 36", 42", 48" and
60" wide

REQUIRED
Epic or WaveWorks worksurfaces and undersurface 2 short and 2 long
storage. overhead supports shown
here due to placement
SPECIFICATION TIPS of overhead
Box/File height undersurface storage without
Place any quantity of Epicenter overhead storage
the end panel grommet or back panel option
units along the run.

Use any width or combination widths. The only

maximum is dictated by the run length.

Not recommended to gang overheads spanning Epicenter Anywhere along top of

more than two surfaces. overhead Epicenter frame
storage

FYI
Short overhead supports are required when
overhead will be placed on a worksurface End trim
hanging off slat inserts. Long overhead supports
are required in all other applications.

Single sided Epicenter overheads have an

unfinished back. An overhead back panel must
be specified separately when using the overhead
in an open plan.

Consider clearance of overhead when specifying

work tools.

National Office Furniture—Specification Guide 71

Product Specification–Epicenter

Worksurfaces
BASICS WORKS WITH
Epic and WaveWorks worksurfaces may be used • Epic or WaveWorks worksurfaces
to create Epicenter open plan configurations. • Epicenter worksurface mounting brackets
• Epicenter worksurfaces
Modified worksurface sizing is available. • Powerlogic Intercoupler system
Includes all appropriate attachment hardware. • Byrne Interlink and Interlink IQ electrical
systems
9 rim options available on WaveWorks. • Worksurface grommets
• Undersurface cable management
2 rim options available on Epic.
components
• Privacy screens and modesty panels
Epic and WaveWorks worksurfaces
• Center drawers, keyboard trays and monitor
• 13⁄16" or 19⁄16" thick
arms
• 18" deep. 30" to 96" wide
• Storage surface cushion on undersurface
in 6" increments
storage worksurface top
• 24" deep. 30" to 96" wide
in 6" increments
• 30" deep. 48" to 96" wide
in 6" increments
• 36" deep. 60" to 84" wide
in 6" increments 1 end 1 or 2 sides 1 or 2 sides
Worksurface
Epicenter depth surfaces wire manager
• 13⁄16" thick
• Softened rim profile 227⁄16" or 285⁄8" deep. Back only
30" to 96" wide in 6" increments Left only
• Knife rim profile 237⁄8" or 30" deep. 30" to Right only Left only
96" wide in 6" increments Back and left Right only
Back and right Left and right
Worksurfaces Wire Managers
A selection of worksurfaces are available with
wire managers on 1 end only or 1 or 2 sides.
Surface grommets may be located left or right
side and on center back.

REQUIRED
Epicenter worksurface mounting brackets.
Epicenter worksurface
Epicenter support base, support panels, support mounting brackets
pedestals and undersurface storage components.

SPECIFICATION TIPS
Return worksurfaces attached anywhere along the
Epicenter slat wall insert with worksurface
mounting brackets may be used in any desired
depth or width.

For undersurface storage, specify worksurface

depth and width to match undersurface storage Epicenter depth
components. Undersurface storage worksurfaces
components
WaveWorks worksurfaces must be specified with a
modified depth of 227⁄16" or 285⁄8" to align with
the Epicenter when used on undersurface storage Box/File height undersurface storage without
components. the end panel grommet or back panel option Support Standard depth
worksurfaces

72 National Office Furniture—Specification Guide

 Product Specification–Epicenter

Work Tools and Accessories

Privacy Screen End Trim Flexible Monitor Arms
BASICS BASICS
Provides seated privacy at the top of the
Epicenter trim cap. Finishes the end of the Epicenter divider at the
end of a run.
Includes appropriate attachment hardware. • 11" End Trim – Use at the end of a double
sided Epicenter when a worksurface is put
Specify length to match divider length.
at the end of a run without an Epicenter.
• 24"-72" wide in 6" increments
• 12" End Trim – Use at the end of a run for
Ability to attach privacy screen to mid and end a double sided Epicenter.
support panels. • 21" End Trim – Use at the end of a run for
a single sided Epicenter, box/file height,
when only the bottom of the Epicenter is
at the end of a run. • Not recommended for use under overheads
• 27" End Trim – Use at the end of a run for • One monitor arm every 24"
a single sided Epicenter, worksurface
height, when only the bottom of the End Trim Filler
Epicenter is at the end of a run.
• 33" End Trim – Use at the end of a single
BASICS
sided Epicenter, box/file height.
• 39" End Trim – Use at the end of a single Fills the space between undersurface storage.
sided Epicenter, worksurface height. • 22", 31" and 37" high

Work Tools
A wide selection of work tools may be specified
to attach anywhere along the slat wall.

Consider items to be stored and their height

when planning for work tool quantities.

Trim Cap
BASICS

Finishes the top of the Epicenter divider.

• 24"-144" wide in 6" increments

Field scribe to desired size.

National Office Furniture—Specification Guide 73

Product Specification–Renegade

Shells
SPECIFICATION TIPS WORKS WITH
BASICS
Shells and linkable shells may be used in any • Powerlogic Intercoupler system
Renegade may be planned and specified using
desired length to create freestanding, linear, • Byrne Interlink and Interlink IQ electrical
assembled or component shells to create
peninsula,“L”, “T” and “U” configurations. systems
freestanding desks and credenzas for private
• Worksurface grommets
office, collaborative and open plan environments. Shells may be configured at box/file height • Undersurface cable management
Renegade or WaveWorks undersurface storage combined with worksurface height. components
components may be added to complete the
Shells and linkable shells may be linked together • Renegade, WaveWorks or Epic set-on
configuration.
in-line or back-to-back to create collaborative overhead storage
Linkable shells may be added to expand environments. • Privacy screens and modesty panels
configurations. • Center drawers, keyboard trays and monitor
Shells will accept any combination of Renegade, arms
Linkable shells include appropriate attachment WaveWorks or Epic set-on overhead storage to
hardware. create private office or open plan environments Freestanding “L” configuration
with a high degree of enclosure.
Shells include modesty panels.

11⁄8" or 13⁄16" thick worksurface in soft rim.

Include leveling glides with 1½" adjustment

range.
Linear or peninsula
“T” configuration
TYPES
Shells
• Worksurface height with full end panel. 24"
or 30" deep. 36"-48" and 60"-72" wide
Assembled Desks and Credenzas
in 6" increments
• Box/File height with full end panel. 21" or
24" deep. 60"-72" wide in 6" increments
• 1 worksurface height full end panel and
“U” configuration
1 box/file height end panel. 21" or 24"
deep. 60"-72" wide in 6" increments

Linkable shells May be specified with

• Worksurface height with 1 full end panel suspended box/file or full
and 1 narrow end panel. 21" or 24" deep. height pedestals
30"-48" and 60"-72" wide
in 6" increments
Shells and Credenza Shells Support panel
• Worksurface height with 2 narrow end
required
panels. 21" or 24" deep. 36"-48" and
60"-72" wide in 6" increments

Credenza shells
• Worksurface and box/file height with full
end panels. 21" or 24" deep. 74" and 110" Greater than 48"
wide

SUPPORT
Renegade shells are self supporting. Linkable
shells with narrow end panels are properly
supported when attached to full end panel
shells.

FYI Box/File
A support panel is required when knee space is height shell Worksurface
greater than 48" height shell
Renegade WaveWorks
Credenza shells are required when filling or Epic set-on
with storage. overhead storage Any combination of Renegade or
WaveWorks undersurface storage

74 National Office Furniture—Specification Guide

 Product Specification–Renegade

Storage
BASICS Undersurface storage
Renegade storage components are available in
wall mount overhead storage, set-on storage
component, freestanding and undersurface
storage components to fit within shells and
credenzas.

All freestanding components have adjustable

glides with a 1½" range.

Wall mount and set-on components include

appropriate attachment hardware.

Multiple pull options are available.

All available with locks. Set-on storage

TYPES
Shell undersurface storage
Worksurface height
• File/File and box/box/file pedestals. 20",
23" and 29" deep
• Lateral files, double door units, bookcase,
mixed storage and multi-file cabinets.
20" and 23" deep. 36" wide
Box/File height
• Box/File pedestals. 20", 23" and 29" deep
• Lateral files, and bookcases. 20" and
23" deep. 36" wide

Set-on storage
• Highback organizers with or without doors.
38" high. 15" deep. 48" and 60"-72" wide
in 6" increments Wall mount overhead storage
• Corner highback organizers without doors.
38" high. 15" deep. 36", 42", 66" or
72" wide
• Bookcases with or without doors. 14" deep.
36" wide. 38" high

Wall mount
• Overhead storage cabinets with or without
doors. 18" high. 15" deep. 30"-48" wide
in 6" increments

Freestanding storage
• 2, 3, and 4 drawer lateral files. 21" or
24" deep. 36" wide
• Component tops for 3 and 4 drawer lateral
files. 11⁄8" or 13⁄16" thick. 21" or Freestanding storage
24" deep. 72" or 108" wide.
• Double door unit. 21" or 24" deep.
29" high. 36" wide
• Multi-file and mixed storage cabinet. 90 degree
21" or 24" deep. 29" high. 36" wide bookcase option
• Storage towers and wardrobe/storage available
cabinets doors, drawers and bookcases.
21" or 24" deep. 67" high. 24" and
36" wide
• Bookcases. 14" deep. 41", 53", and
67" high. 36" wide
• Box/File mobile pedestals, with or without
cushion top

National Office Furniture—Specification Guide 75

Product Specification–Renegade

Storage (continued)
SPECIFICATION TIPS
Wall mount overhead storage to utilize wall
space in private office and collaborative
environments around the perimeter space. Accepts tack
board, marker
Set-on storage may be used to create work space
board or slat
privacy when placed back to back. Consider
Back-to-back wall
location of worksurface grommets when selecting
for maximum
overhead storage. privacy
Consider freestanding storage components
heights when used adjacent to mounted
overhead storage.

Multiple undersurface storage components may

be placed within a shell.

Add a cushion to shell top or use a pedestal with

a cushion top for additional seating.
Specify height to match
3 lateral files may be ganged together under a
common component top to create a counter
height workcenter.

Vary the height of long runs of freestanding

storage to compensate for uneven floors, while
providing visual interest. Add a cushion

Ganging bracket available for undersurface Multiple undersurface storage

storage to provide a clean aesthetic. components within a single
common shell
When creating a storage credenza, must specify
shell in 74" or 110" to accommodate
undersurface storage.

WORKS WITH Component top

• Shells and linkable shells
• Task lights for highback organizers
• Interior drawer accessories for box, file and Creates a workcenter
lateral file drawers
• Interior accessories for open storage
• Storage surface cushion
• Tack board, marker board and slat wall for
highback organizers Vary component height

76 National Office Furniture—Specification Guide

 Product Specification–WaveWorks, Renegade and Epic

Cable Management
May span
BASICS
worksurfaces
Multiple cable managers and covers are available
to manage and route cables below the
Surface height
worksurface vertically and horizontally.
power/data access

Wire Managers Undersurface

Includes appropriate attachment hardware. wire manager
Vertical Wire Managers attach to the underside of
the worksurface.

SPECIFICATION TIPS
Use cable managers and covers to route and To building
manage cables below the worksurface from the power/data
worksurface top to the power/data source. Vertical wire managers
route cables down table leg
Multiple cable managers may be used below the
worksurfaces and to manage cable from one To building
worksurface to the next. power/data
Consider location of undersurface storage,
supports and worksurface grommets and
power/data components when planning for cable
manager type and length.

May also be used below ganged tables to manage

cables from one table to the next.

Vertical wire managers

are flexible to accommodate
user needs; used to
conceal power in-feed
and data cables

Horizontal wire manager

used to conceal power
in-feed and data cables

National Office Furniture—Specification Guide 77

Product Specification–WaveWorks, Renegade and Epic

-Work Tools and Accessories

Vertical Pigeon Hole Storage Storage Surface Cushion Task Lights
BASICS BASICS BASICS
Designed to fit below highback organizer to Provides guest seating on box/file height Mount below storage on highback organizer or
provide easy access to small items and papers. undersurface storage top. below overhead storage.
• Vertical pigeon hole storage. 3 fixed Task Light
Specify size to match worksurface size.
shelves • 5" deep. 23" or 47" wide. 2" high LED task
FYI light
May interfere with tack board, when placed LED task light
below highback organizer. Specify shorter width • 3½" deep. 22", 28" or 34" wide. 1½" high.
tack board to allow unit to fit flush against back Can daisy chain up to 3
of organizer. LED strip light (magnetic)
• 1" deep. 16", 25", or 31" wide. 1" high.
Can daisy chain up to 3.

Tack Boards, Marker Boards

and Slat Walls
BASICS
Marker boards and slat wall may be wall
attached. Tack boards may be wall attached or
attached within highback organizer.
When specifying tack board, refer to the tack
Organizing Stacker board applicability charts in the Casegoods Book
BASICS 2 Price List.
Provides an accessory shelf anywhere within a
Slat wall will support work tools.
highback organizer overhead storage or
bookcase.
• 1 shelf Center Drawers and
• 13" deep. 32" to 41" wide. 5" high Keyboard Trays
BASICS
Mount kneespace or clear area below workspace.
Consider width and depth of worksurface when
specifying.

Metal Storage Cubby

BASICS
Provides an accessory shelf anywhere below an
Epic 13" high overhead storage cabinet.
• 1 shelf
• 13" deep. 30" to 48" wide. 5" high

78 National Office Furniture—Specification Guide

 Product Specification–WaveWorks, Renegade and Epic

Work Tools Flexible Monitor Arms -

A wide selection of work tools may be specified Grommet and Clamp
to attach anywhere along the slat wall.
Attach to worksurface through grommet mount
Consider items to be stored and their height or clamp mount.
when planning for work tool quantities
Consider interference with other components
above and behind monitor arm when specifying
location on the worksurface.
Not recommended for use with knife edge
worksurfaces, flip/nest training tables or a top
that is utilizing any metal base.
When there is a worksurface overhang
(Ex: 24"D pedestal with a 30"D worksurface), it
is recommended that a customer use a grommet
mount monitor arm versus a clamp mount
Privacy Screen monitor arm.
BASICS Not recommended to turn the monitor arms away
Privacy Screens may be applied to component from the user side.
worksurfaces, tables and undersurface storage
worksurfaces to add seated privacy.
Includes appropriate attachment hardware.

Privacy Screens Set-On Surface

• Acrylic tapered or rectangular and felt
rectangular
• 18" high.
• 21", 24", 27", 30", 36", 42", 48", 54", 60"
and 72" wide.

Privacy Screens Edge Mount Modesty/Privacy

• Rectangular
• 32" high.
• 21", 24", 27", 30", 36", 42", 48", 54", 60" Edge mount Edge mount
and 72" wide. modesty/privacy screen privacy screen

Privacy Screens Edge Mount Privacy

• Rectangular or tapered
• 20" high.
• 21", 24", 27", 30", 36", 42", 48", 54", 60"
and 72" wide. Tapered privacy
screen Epicenter
mount

Mid support
privacy panel

End support
privacy panel

National Office Furniture—Specification Guide 79

Notes

80 National Office Furniture—Specification Guide

NPGC Specification Guide Cover_Ver 14_Layout 1 5/1/14 12:02 PM Page 1

Specification Guide
Specification
Guide Epicenter®
Epic® Casegoods
Exhibit™ Wall Rail Solution
Renegade™ Casegoods
WaveWorks® Casegoods

Effective June 3, 2013

www.NationalOfficeFurniture.com
1205 Kimball Boulevard, Jasper, IN 47549
800.482.1717 Fax 812.482.8800
©Kimball International, Inc. 2014
Printed in the USA
Form No. NSPEC Ver. 14
A Unit of Kimball International
Effective June 2, 2014