0% found this document useful (0 votes)
316 views13 pages

Ps 1

This document contains multiple choice questions and answers about power system insulators. It covers topics like the properties of insulator materials, how to increase string efficiency, the types of insulators used for different voltages, and factors that affect insulator performance like impurities, temperature changes, and guard rings. There are over 40 questions in total related to insulator selection and design for overhead transmission lines.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
316 views13 pages

Ps 1

This document contains multiple choice questions and answers about power system insulators. It covers topics like the properties of insulator materials, how to increase string efficiency, the types of insulators used for different voltages, and factors that affect insulator performance like impurities, temperature changes, and guard rings. There are over 40 questions in total related to insulator selection and design for overhead transmission lines.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

Power System 1- Unit – II MCQ

QUESTION The property of materials by which they can be drawn into wires is known as
A ductility
B malleability
C creep
D elasticity
CORRECT ANS A

QUESTION The string efficiency of an insulator can be increased by


A grading of insulators
B deceasing number of strings in the insulator
C increasing number of strings in the insulator
D none of above
CORRECT ANS C

QUESTION The insulator should have


A low insulating resistance
B high relative permittivity
C mechanically weak
D low relative permittivity
CORRECT ANS B

QUESTION Pure insulators are used to support


A bus bars
B line conductors
C telephone lines
D terminal posts of battery
CORRECT ANS A

QUESTION The insulator is so designed that it should fail only by ...................


A flashover
B puncture
C both a and b
D none
CORRECT ANS A

QUESTION If the voltage across the string of the string insulator assembly is 38 kv, no. of insulation disc are 4 and
voltage across the lower most disc is 12 kv, the string efficiency is
A 76.50%
B 70%
C 50%
D 100%
CORRECT ANS A

QUESTION The most common cause of insulator damage is


A puncture
B Porosity
C Aging
D Flashover
CORRECT ANS A

QUESTION When an insulator is subjected to alternate varying heat and cold,________may in the insulator
A porosity
B flashover
C puncture
D cracking
CORRECT ANS D

QUESTION Impurities in the insulator material decreases ______


A dielectric strength
B porosity
C mechanical strength
D toughness of insulator
CORRECT ANS A

QUESTION Suspension insulator is advantageous than


A pin insulator
B post insulator
C strain insulator
D none of above
CORRECT ANS A
Power System 1- Unit – II MCQ

QUESTION How string efficiency can be improved for insulator ?


A grading the insulator
B using long cross arm
C using a guard ring
D any of above
CORRECT ANS D

QUESTION Pin type insulator are not used for voltages beyond
A 1kv
B 11kv
C 22kv
D 33kv
CORRECT ANS D

QUESTION Strain type insulator are use where the conductor are
A dead end
B at intermediate anchor towers
C any of above
D none of above
CORRECT ANS C
QUESTION For 66 kV lines the number of insulator disc used as
A 3
B 6
C 10
D 12
CORRECT ANS B

QUESTION Seven disc usually suggest that the transmission line voltage is
A 11kv
B 33kv
C 66kv
D 132kv
CORRECT ANS D

QUESTION Electric power may be transmitted by


A underground system
B overhead system
C both of above
D none of above
CORRECT ANS C

QUESTION A line which connect a consumer to the distributor is called


A distribution
B feeder
C service mains
D none of above
CORRECT ANS C

QUESTION Bulk power consumer are usually supplied at


A 11kv
B 66kv
C 330kv
D 400kv
CORRECT ANS A

QUESTION Service mains links


A distribution transformer to consumer area
B line to the consumer area to the premises of the consumer
C generating station with receiving end substation
D receiving end substation to distribution transformer
CORRECT ANS B

QUESTION The potential across the various disc insulator of suspension string is different because of
A shunt capacitance
B series & shunt capacitance
C series capacitance
D none of these
CORRECT ANS A
Power System 1- Unit – II MCQ
QUESTION Which type of insulator are used on 132 kv transmission lines ?
A disc type
B shackle type
C pin type
D pin & shackle type
CORRECT ANS A

QUESTION The purpose of guard ring is


A to reduce the transmission losses
B to reduce the earth capacitance of the lowest unit
C to increase the earth capacitance of the lowest unit
D none of these
CORRECT ANS B

QUESTION What type of insulator will be used if the direction of the transmission line is changed?
A strain type
B shackle type
C suspension type
D pin type
CORRECT ANS B

QUESTION Which insulator can be used either vertical or horizontal position


A strain type
B shackle type
C suspension type
D pin type
CORRECT ANS B

QUESTION The string efficiency of an insulator can be increased by


A reducing the number of strings in it
B increasing the number of strings in the insulator
C correct grading of insulator or various capacitance
D none of these
CORRECT ANS C

QUESTION High voltage trasnmission line use


A pin insulator
B suspension insulator
C both of above
D none of above
CORRECT ANS B

QUESTION The guard ring in insulator of transmission towers are used to


A reduced the transimission losses
B reduced the earth capacitance of the lowest unit of insulator
C incease the earth capacitance of the lowest unit of insulator
D none of above
CORRECT ANS B

QUESTION By using a guard ring, string efficiency of suspension insulator will be


A constant
B increased
C decreased
D independent of shunt capacitance
CORRECT ANS B

QUESTION 220 kV transimission line employs


A disk Type insulators
B pin type insulator
C shackle type insulator
D none of the above
CORRECT ANS A

QUESTION 400 V line at dead end employs


A pin type insulator
B disc type inulator
C strain insulator
D shackle insulator
CORRECT ANS C
Power System 1- Unit – II MCQ

QUESTION Porcelain insulators are glazed


A to improve the appearance
B to prevent absorption of gases and water vapours
C so that water should glide down easily
D due to all of above
CORRECT ANS B

QUESTION Petticoats are provided in the pin type insulator


A to drip the rain
B to improve the appearance of the insulator
C to protect the pin of the insulator from the effect of sun and rain
D due to all of above
CORRECT ANS A

QUESTION The string efficiency of transmission line is increased


A by grading of the mutual caacitance of the insulator in the string with high capacity
B by reducing the ratio of shunt capacitance to mutual capacitance to mutual capacitance of the insulator
C by all above methods
D by grading the shunt capacitance of the insulator in the string such that bottom insulator has highest shunt capacitance
CORRECT ANS C

QUESTION Grading of shunt capacitance of the insulator in a string is achieved by


A reducing the number of strings
B fitting sheet metal caps in contact with the porcelain
C fitting grading ring to establish direct capacitance between the line conductor and the insulator caps
D both of method b and c
CORRECT ANS D

QUESTION Disc type insulator employed as suspension insulator have


A disc at 45 degree to the horizontal
B disc in vertical plane
C disc in the horizontal plane
D none of above
CORRECT ANS C

QUESTION In EHV transmission line having very long spam conductor are suspended by
A Y type string of disc insulator
B Single string of disc insulator
C double string of disc in parallel
D none of above methods
CORRECT ANS C

QUESTION Two most suitable material for insulator


A toughened glass and pvc
B pvc and porcelain
C toughned glass and porcelain
D pvc and fibre glass
CORRECT ANS C

QUESTION Isolators are normally operated at


A Full load current condition
B No load current condition
C No current condition
D Fault current condition
CORRECT ANS C

QUESTION The amount of excitation provided depends upon


A Supply voltage
B Frequency
C Load current
D None of above
CORRECT ANS C

QUESTION Insulators used at voltage level of 132 kV are


A Pin Insulators
B String Insulators
C Post Insulators
D Pin & Shackle Insulators
CORRECT ANS B
Power System 1- Unit – II MCQ

QUESTION The string efficiency of a string of suspension insulators is dependent on


A Size of insulators
B Number of discs in the string
C Size of tower
D None of above
CORRECT ANS B

QUESTION What is the value of safety factor of pin type insulator


A 12
B 8
C 10
D 7
CORRECT ANS C

QUESTION High voltage transmission line use:


A suspension insulator
B pin insulator
C both a and b
D none of the above
CORRECT ANS A

QUESTION The corona is affected by which of the following?


A size of the conductor
B shape of the conductor
C surface condition of conductor
D all of the above .
CORRECT ANS D

QUESTION String efficiency can be improved by


A using Longer cross arm
B grading the insulator
C using a guard ring
D any of the above.
CORRECT ANS D

QUESTION A string efficiency of 100% implies that


A shunt capacitance is 1 MF
B potential across each disc is same
C potential across each disc is zero
D one of the insulator disc is shorted.
CORRECT ANS B

QUESTION Corona effect can be detected by


A hissing sound
B faint luminous flow of bluish color
C presence of ozone detected by odor
D all of the above.
CORRECT ANS D

QUESTION Corona usually occurs when the electrostatic stress in the air around the conductor succeeds
A 30 kV (maximum value)/cm
B 22 kV (maximum value)/cm
C 11 kV (rms value)/cm
D 6.6 kv (rms value)/cm
CORRECT ANS A

QUESTION The effect of corona is


A increased energy loss
B increased reactance
C increased inductance
D all of the above.
CORRECT ANS A

QUESTION Ten discs usually suggest that the transmission line voltage is
A 11 kV
B 33 kV
C 66 kV
D 132 kV.
CORRECT ANS D
Power System 1- Unit – II MCQ

QUESTION For 66 kV lines the number of insulator discs used is


A 3
B 5
C 8
D 12
CORRECT ANS B

QUESTION Strain type insulator arc used where the conductors arc
A Dead ended
B at intermediate anchor towers
C any of the above
D none of the above.
CORRECT ANS C

QUESTION Transmission line insulators are generally made up of


A Glass
B Porcelain
C Iron
D P.V.C
CORRECT ANS B

QUESTION High voltage transmission line use:


A suspension insulator
B pin insulator
C both a and b
D none of the above .
CORRECT ANS A

QUESTION By which of the following system electric power can be transmitted?


A overhead system
B underground
C both a and b
D none of the above .
CORRECT ANS C

QUESTION There are how many types of tariffs?


A 2
B 3
C 5
D 10
CORRECT ANS D

QUESTION Which conductors connect the consumer’s terminals to distribution?


A service mains
B distributors
C feeders
D none of the above
CORRECT ANS A

QUESTION The underground system cannot be operated above which voltage level?
A 440 V
B 66 KV
C 33 KV
D 11 KV
CORRECT ANS B

QUESTION Overhead lines can be designed for operation upto:


A 11 KV
B 400 KV
C 66 KV
D 33 KV
CORRECT ANS B

QUESTION Among the options which metal has the highest electrical conductivity?
A Aluminum.
B Stranded aluminum.
C Copper.
D Steel.
CORRECT ANS C
Power System 1- Unit – II MCQ

QUESTION Insulated cables are usually rated by their :


A operating voltage.
B operating voltage and highest operating temperature.
C operating temperature.
D cost.
CORRECT ANS B

QUESTION Typically busbars look like:


A flat strips or hollow tubes.
B Flat strips.
C hollow tubes.
D wire.
CORRECT ANS A

QUESTION Which of the following is not usually the trans-mission voltage?


A 66 kV
B l32kV
C 264 kV
D 400 kV
CORRECT ANS C

QUESTION Which of the following is usually not the generating voltage?


A 6.6 kV
B 9.9 kV
C 11kV
D 13.2 kV.
CORRECT ANS B

QUESTION Boosters are basically


A inductors
B capacitors
C transformers
D synchronous motors.
CORRECT ANS C

QUESTION Which of the following is not the distribution system normally used
A 3 phase
B 3 phase
C Single phase
D Single phase
CORRECT ANS D

QUESTION Conductors for high voltage transmission lines are suspended from towers
A to reduce clearance from ground
B to increase clearance from ground
C to reduce wind and snow loads
D to take care of extension in length during summer.
CORRECT ANS B

QUESTION Transmission efficiency increases as


A voltage and power factor both increase
B voltage and power factor both decrease
C voltage increases but power factor decreases
D voltage decreases but power factor increases
CORRECT ANS A

QUESTION Pin insulators are normally used up to voltage of about


A 100kV
B 66 kV
C 33 kV
D 25 kV.
CORRECT ANS D

QUESTION Strain type insulator arc used where the conductors arc
A dead ended
B at intermediate anchor towers
C any of the above
D none of the above.
CORRECT ANS C
Power System 1- Unit – II MCQ

QUESTION For 66 kV lines the number of insulator discs used are


A 3
B 5
C 8
D 12
CORRECT ANS B

QUESTION Ten discs usually suggest that the transmission line voltage is
A 11 kV
B 33 kV
C 66 kV
D 132 kV
CORRECT ANS D

QUESTION The effect of corona is


A increased energy loss
B increased reactance
C increased inductance
D all of the above.
CORRECT ANS A

QUESTION Corona usually occurs when the electrostatic stress in the air around the conductor succeeds
A 30 kV (maximum value)/cm
B 22 kV (maximum value)/cm
C 11 kV (rms value)/cm
D 6.6 kv (rms value)/cm
CORRECT ANS A

QUESTION Corona effect can be detected by


A hissing sound
B faint luminous flow of bluish color
C presence of ozone detected by odor
D all of the above.
CORRECT ANS D

QUESTION The current drawn by the line due to corona losses is


A sinusoidal
B square
C non-sinusoidal
D none of the above
CORRECT ANS C

QUESTION Presence of ozone as a result of corona is harmful because


A it gives bad odor
B it corrodes the material
C it transfers energy to the ground
D reduces power factor.
CORRECT ANS B

QUESTION In transmission system a feeder feeds power to


A service mains
B generating stations
C distributors
D all of the above.
CORRECT ANS C

QUESTION The chances of corona are maximum in


A domestic wiring
B distribution lines
C transmission lines
D all of the above.
CORRECT ANS C

QUESTION Transmission lines link


A service points to consumer premises
B distribution transformer to consumer premises
C receiving end station to distribution transformer
D generating station to receiving end station
CORRECT ANS D
Power System 1- Unit – II MCQ

QUESTION Which type of insulators are used on 132 kV transmission lines?


A Pin type
B Disc type
C Shackle type
D Pin and shackle type.
CORRECT ANS B

QUESTION String efficiency can be improved by


A using Longer cross arm
B grading the insulator
C using a guard ring
D any of the above.
CORRECT ANS D

QUESTION Minimum horizontal clearance of a low voltage transmission line from residential buildings must be
A 1 & ½ feet
B 3 feet
C 4 feet
D 8 feet.
CORRECT ANS C

QUESTION If a 66 kV lines passes over a residential building, the minimum vertical clearance from the roof of
the building must be
A 8 feet
B 12 feet
C 13 feet
D 16 feet
CORRECT ANS C

QUESTION Alternating current power is transmitted at high voltage


A to safeguard against pilferage
B to minimize transmission losses
C to reduce cost of generation
D to make the system reliable.
CORRECT ANS B

QUESTION The permissible voltage variation in transmission and distribution system is


A ± 0.1%
B ± 1%
C ±10%
D ± 25%.
CORRECT ANS C

QUESTION The voltage of transmission can be regulated by


A use of tap changing transformers
B switching in shunt capacitors at the receiving end during heavy loads
C use of series capacitors to neutralize the effect of series reactance
D any of the above methods.
CORRECT ANS D

QUESTION The most economic voltage for transmitting given power over a known distance by overhead
transmission line is approximately
A 3.6 kV/km
B 1.6 kV/km
C 2.6 kV/km
D 3.6 kVkm.
CORRECT ANS A

QUESTION String efficiency is given by


A (voltage across the string) / ((numbers of discs on the string) x (voltage across disc nearest to the
conductor))
B ((voltage across the string) x (numbers of discs on the string)) / (voltage across disc nearest to the
conductor)
C ((voltage across disc nearest to the conductor) x (numbers of discs on the string)) / (voltage across the
string)
D (Voltage across disc nearest to the conductor))/ ((numbers of discs on the string) x (voltage across the
string)
CORRECT ANS A
Power System 1- Unit – II MCQ

QUESTION Which distribution system is more reliable?


A Ring main system
B Tree system
C Radial system
D All are equally reliable.
CORRECT ANS A

QUESTION Step-up substations are associated with


A distributors
B consumer location
C concentrated load
D generating stations.
CORRECT ANS D

QUESTION Consumers having low power factor equipment are advised to install
A tap changing transformer
B capacitor bank
C synchronous condensers
D none of the above.
CORRECT ANS B

QUESTION A bus bar is rated by


A current only
B current and voltage only
C current, voltage, frequency
D Current, voltage, frequency and short time current.
CORRECT ANS D

QUESTION Material generally used for bus bar is


A copper
B aluminum
C steel
D tungsten
CORRECT ANS B

QUESTION Isolators are used to disconnect a circuit when


A line is on full load
B line is energized
C circuit breaker is not open
D there is no current in the line
CORRECT ANS D

QUESTION Tap changing transformers are used for


A stepping up the voltage
B stepping down the voltage
C both stepping up and stepping down the voltage
D Supplying low voltage current for instruments.
CORRECT ANS C

QUESTION Which device automatically interrupts the supply in the event of surges
A Earthing switch
B Series reactor
C Isolator
D Circuit breaker.
CORRECT ANS D

QUESTION In a substation the equipment used to limit short circuit current level is
A Series reactor
B Coupling capacitor
C Lightening switch
D Isolator.
CORRECT ANS A
Power System 1- Unit – II MCQ
QUESTION Which of the following equipment is not installed in a substation?
A Shunt reactors
B Exciters
C Voltage transformers
D Series capacitors.
CORRECT ANS B

QUESTION Which bus bar scheme offers the lowest cost?


A Single bus bar scheme
B Ring bus bar scheme
C Breaker and a half scheme
D Main and transfer scheme.
CORRECT ANS A

QUESTION Which is the most expensive bus bar scheme?


A Single bus bar scheme
B Ring bus bar scheme
C Double bus bar double breaker
D Main and transfer scheme.
CORRECT ANS C

QUESTION Current rating is not necessary in case of


A Isolators
B Circuit breakers
C Load break switches
D Circuit breakers and load break switches.
CORRECT ANS A

QUESTION Which of the following correctly represents the sequence of operations of isolator circuit breaker
and earthing switch while opening a circuit
A Close earthing switch - open circuit breaker open isolator
B Open isolator - close circuit breaker - open earthing switch
C Open circuit breaker - open isolator - close earthing switch
D Close circuit breaker - close isolator - open earthing switch.
CORRECT ANS C

QUESTION Which of the following correctly presents the sequence of operations of isolator circuit breaker and
earthing switch while closing a circuit
A Ensure circuit breaker is closed - close isolator - open earthing switch
B Ensure circuit breaker is open - close isolator - open earthing switch if any close circuit breaker
C Ensure circuit breaker is open - open isolator - open earthing switch if any - close circuit breaker.
D None of the above.
CORRECT ANS B

QUESTION Which of the following type tests are conducted on isolators?


A Temperature rise test
B Impulse stage with stand test
C Short time current test
D All of the above.
CORRECT ANS D

QUESTION In a balance 3 φ , 4 wire AC system, the phase sequence is RYB. If the voltage of R phase is 230 <
0° V, then for Y phase
A 230 < 0 V
B 230 < 60° V
C 230 < 90°V
D 230 < 120° V.
CORRECT ANS D

QUESTION Voltages under Extra High Voltage are


A 1 kV and above
B 11 kV and above
ANS C 132 kV and above
D 330 kV and above.
Power System 1- Unit – II MCQ

QUESTION In outdoor substation, the lightening arresters is placed nearer to


A the isolator
B the current transformer
C the power transformer
D the current breaker.
CORRECT ANS C

QUESTION Aluminum is being favored as bus-bar material mainly because of


A case of fabrication
B low density
C low cost
D non availability of copper.
CORRECT ANS C

QUESTION Which section can lie used for bus bar ?


A bars
B rods
C tubes
D any of the above.
CORRECT ANS D

QUESTION Which type of copper wire will have highest tensile strength?
A Soft drawn
B Medium drawn
C Hard drawn
D None of these
CORRECT ANS C

QUESTION Guy wire is used to


A Support the pole
B Provide protection against surges
C Provide emergency earth route
D Protect conductors against short circuiting.
CORRECT ANS A

QUESTION Which of the following is a leading power system?


A Underground cables
B Reactors
C Mercury arc rectifiers
D Transformers.
CORRECT ANS A

QUESTION Which of the following is a static exciter ?


A dc separately excited generator
B Amplidyne
C Retool
D Rectifier.
CORRECT ANS D

QUESTION The service mains connect


A distributor and consumer terminals
B distributor and transformer
C distributor and relay system
D Transformer and earth
CORRECT ANS A

QUESTION A 66 kV system has string insulator having five discs and the earth to disc capacitance ratio of
0.10, The string efficiency will be
A 89%
B 75%
C 67%
D 55%.
CORRECT ANS C
Power System 1- Unit – II MCQ

QUESTION A 66 kV system has string insulator having five discs and the earth to disc capacitance ratio of
0.10, The voltage shared by the individual discs will be
A 1.25 kV
B 2.50 kV
C 3.88 kV
D 5.28 kV.
CORRECT ANS D

QUESTION The corona is affected by which of the following?


A size of the conductor
B shape of the conductor
C surface condition of conductor
D all of the above
CORRECT ANS D

QUESTION A booster is a:
A series wound generator
B shunt wound generator
C synchronous generator
D none of the above.
CORRECT ANS A

QUESTION Insulations are provided in which type of transmission system?


A Underground transmission system.
B Overhead transmission system.
C In both of them.
D Insulation is not required anywhere.
CORRECT ANS A

QUESTION Guess the widely used metal for overhead transmission?


A Copper.
B Aluminum.
C Steel.
D iron cable.
CORRECT ANS B

You might also like