ADM2 Fault Codes Diagnosis, Version 203

DTC Description Remedial action

- check wiring
1 00 03 decompression valve MBR_KD open circuit
- check solenoid valve
- check wiring
1 00 04 decompression valve MBR_KD shorted to ground
- check solenoid valve 15/10
vehicle
- check wiring
1 01 03 speed open circuit
- check parameter 08/01 15/03
signal C3
vehicle
1 01 04 speed shorted to ground -check wiring 15/03
signal C3

vehicle
1 01 14 speed value not plausible - check parameter 08/01
signal C3
- restart accelerator pedal adjustment routine
analog
- check wiring
1 02 00 accelerator accelerator pedal not adjusted
- Limit value idle operation position: 5,0V
pedal
- Limit value kickdown position: 4,9 V
- Pedal unit exchange, if defective
analog
- check wiring
1 02 02 accelerator voltage not plausible
- Limit value idle operation position: 5,0V
pedal
- Limit value kickdown position: 4,9 V

- Pedal unit exchange, if defective

analog
voltage too high or shorted to - check wiring
1 02 03 accelerator
battery voltage - Limit value idle operation position: 5,0V
pedal
- Limit value kickdown position: 4,9 V

- Pedal unit exchange, if defective

analog
voltage too low or shorted to - check wiring
1 02 04 accelerator
ground - Limit value idle operation position: 5,0V
pedal AFPS
- Limit value kickdown position: 4,9 V

1
DTC Description Remedial action

- oil discharge with to strong overstocking

1 04 00 oil level oil level to high - remark: This problem can occur also if in PLD-MR the false
type of oil pan were programmed

1 04 01 oil level low oil level - refill oil

- refill oil
1 04 14 oil level oil level too low - remark: This problem can occur also if in PLD-MR the false
type of oil pan were programmed

1 05 01 oil pressure sensor low oil pressure - check oil pump and oil circuit
1 05 14 oil pressure sensor oil pressure too low - check oil pump and oil circuit.
1 08 00 air filter sensor air pressure too high - check wiring.
1 08 03 air filter sensor open circuit - check wiring.
1 08 04 air filter sensor shorted to ground - check wiring.

1 09 00 coolant temperature high coolant temperature - cooling-water level and cooling circuit check
1 09 14 coolant temperature coolant temperature too high - cooling-water level and cooling circuit check
- refill coolant
1 10 01 coolant level low coolant level
- check wiring
- check wiring
1 10 03 coolant level open circuit
- Voltage must be larger than 2,0 V.
1 10 04 coolant level shorted to ground -check wiring.
- check battery voltage
1 11 00 terminal 15 (ignition0 over voltage - check parameter 2/08
(24V/12V selection)
- check battery voltage
1 11 01 terminal 15 (ignition0 under voltage - check parameter 2/08
(24V/12V selection)

both switches open circuit - check wiring

1 17 05 idle switch (analog pedal)
(GAS2+GAS1 open) - Pedal unit exchange, if defective

2
DTC Description Remedial action
both switches open circuit - check wiring
1 17 12 idle switch (analog pedal)
(GAS2+GAS1 closed) - Pedal unit exchange, if defective

1 18 12 cruise control switch CC+ and CC- both switches closed - check wiring- check cruise control switch

- check wiring
1 19 12 cruise control switch CC+ and CC- both switches closed
- check cruise control switch

1 21 03 power supply analog pedal (AFP+) voltage too high - supply voltage > 5,2 V.

1 21 04 power supply analog pedal (AFP+) voltage too low - supply voltage < 4,8 V.

-check wiring (engine CAN)

-check configuration:

MR parameter (../..) and

1 22 02 CAN link ADM2 - MR no communication with MR
ADM2 parameter 1/01

to be set to equal functionality

(one wire capability)

-check wiring (engine CAN)

-check configuration:

MR parameter (../..) and

1 22 14 CAN link ADM2 - MR one wire mode
ADM2 parameter 1/01

to be set to equal functionality

(one wire capability)

1 23 12 ADM2 internal error

- check wiring
1 33 05 output relay 1 open circuit
- check relay 1

- check wiring
1 33 06 output relay 1 shorted to ground
- check relay 1

3
DTC Description Remedial action
grid heater: no increasing boost - check wiring
1 39 00 output relay 2
temperature after activation - check relay 2

grid heater: relay permanently - check wiring

1 39 01 output relay 2
closed - check relay 2

grid heater: relay permanently - check wiring

1 39 02 output relay 2
closed - check relay 2
voltage too high or shorted to
1 39 03 output relay 2 - check wiring
battery voltage
voltage too low or shorted to - check wiring
1 39 04 output relay 2
ground - check relay 2

- limit values for the supply voltage of the HFG

1 42 02 remote pedal HFG supply voltage out of range Minimum value: 4,8 V and
maximum value: 5,2 V

voltage too high or shorted to - check wiring

1 42 03 remote pedal HFG
battery voltage - check remote pedal

voltage too low or shorted to - check wiring

1 42 04 remote pedal HFG
ground - check remote pedal

- check wiring
1 44 03 output relay 4 open circuit
- check relay 4

- check wiring
1 44 04 output relay 4 shorted to ground
- check relay 4
output PMW pedal supply or
1 45 03 open circuit - check wiring.
transmission
output PMW pedal supply or
1 45 04 shorted to ground - check wiring.
transmission
- check wiring
1 46 03 exhaust brake valve MBR_BK open circuit
- check exhaust brake valve 15/06

- check wiring
1 46 04 exhaust brake valve MBR_BK shorted to ground
- check exhaust brake valve 15/06

4
DTC Description Remedial action
CAN identifiers ETC#1 or ACC#1
1 49 02 71939 CAN-interface - PGN ETC 1 was received only once and did not disappear.
missing

1 50 01 PWM accelerator pedal no supply voltage - check wiring

both signals missing (GAS1 and - check wiring

1 50 02 PWM accelerator pedal
GAS2) - Pins 21/13, 21/12, 15/05 , 21/14
- check wiring
1 50 03 PWM accelerator pedal signal GAS2, not available
- Pins 21/13, 15/05 , 21/14.
- check wiring
1 50 04 PWM accelerator pedal signal GAS1, not available
- Pins 21/12, 15/05 , 21/14.

1 50 05 PWM accelerator pedal accelerator pedal not adjusted - restart accelerator pedal adjustment routine

1 50 06 PWM accelerator pedal idle position out of adjusted range - restart accelerator pedal adjustment routine

accelerator pedal out of adjusted

1 50 07 PWM accelerator pedal - restart accelerator pedal adjustment routine
range