GENERAL NOTES ELECTRICAL DRAWING LIST ELECTRICAL SYMBOLS

GENERAL RACEWAYS FOR TELECOMMUNICATION SYSTEMS:

DRAWING
DRAWING DESCRIPTION A LIGHTING FIXTURE, LETTER INDICATES TYPE, # INDICATED CIRCUIT (TYPICAL)
NUMBER #
1. WHEN A CONFLICT BETWEEN THE DRAWINGS, NOTES AND/OR SPECIFICATIONS OCCUR, THE MORE 1. PROVIDE EMPTY CONDUIT SYSTEMS FOR TELECOMMUNICATION WORK, COMPLETE WITH PULL BOXES, A LIGHTING FIXTURE WITH EMERGENCY BATTERY
STRINGENT, AND/OR LARGER QUANTITY AND/OR MORE EXPENSIVE SHALL APPLY. THE OUTLET BOXES, AND CONDUIT AS INDICATED ON THE DRAWINGS. #
E-001 COVER SHEET - ELECTRICAL
REQUIREMENTS LISTED WITHIN NOTES OR SPECIFICATIONS SHALL BE REQUIRED, PROVIDED AND
INSTALLED WHETHER SPECIFICALLY INDICATED ON THE DRAWINGS OR NOT. 2. PROVIDE MINIMUM INSIDE BENDING RADIUS OF 10 TIMES CONDUIT INSIDE DIAMETER FOR S SINGLE POLE SWITCH, LETTER INDICATES LIGHTING ZONE (TYPICAL)
TELECOMMUNICATIONS RACEWAYS.
E-002 LIGHTING FIXTURE SCHEDULE - ELECTRICAL
WIRING & RACEWAY: S MANUAL MOTOR STARTER WITH THERMAL OVERLOAD
3. WHEN COMPLETED THE CONDUIT SYSTEMS SHALL BE READY FOR THE INSTALLATION OF WIRING AND
1. THE DRAWINGS SHOW THE GENERAL LAYOUT AND TYPICAL DETAILS. PROVIDE COMPLETE SYSTEMS. EQUIPMENT.
DRAWINGS ARE BASED ON THE SPECIFIED EQUIPMENT. RACEWAY LAYOUTS, BOXES, AND WIRING OF
S LOW VOLTAGE SWITCH
ED-102 PARTIAL SECOND FLOOR DEMOLITION PLAN - ELECTRICAL
THE SYSTEMS ARE SUBJECT TO APPROVED SHOP DRAWINGS. 4. FROM EACH OUTLET PROVIDE A 1" EMPTY EMT CONDUIT ROUTED INTO THE CEILING CAVITY OR TO
THE CLOSEST TELECOMMUNICATIONS CLOSET. PROVIDE A DRAG LINE IN EACH RUN AND TERMINATE S LOW VOLTAGE DIMMER SWITCH
2. ENSURE THAT ITEMS TO BE FURNISHED FIT THE SPACE AVAILABLE. MAKE NECESSARY FIELD IN A BUSHED ELBOW.
MEASUREMENTS TO ASCERTAIN SPACE REQUIREMENTS, INCLUDING THOSE FOR CONNECTIONS, AND E-101 PARTIAL FIRST FLOOR PLAN - ELECTRICAL
S WALL MOUNTED OCCUPANCY SENSOR WITH MANUAL OVERRIDE
PROVIDE SUCH SIZES AND SHAPES OF EQUIPMENT THAT FINAL INSTALLATION SHALL SATISFY THE MECHANICAL EQUIPMENT WIRING:
INTENT OF THE DRAWINGS AND SPECIFICATIONS.
1. UNLESS OTHERWISE INDICATED OR SPECIFIED HEREIN, ALL MOTORS, MOTOR STARTERS, MOTOR E-102 PARTIAL SECOND FLOOR PLAN - ELECTRICAL S WALL MOUNTED VACANCY SENSOR WITH MANUAL OVERRIDE
3. LOCATIONS OF OUTLETS, SWITCHES, APPLIANCES, ETC. AS SHOWN ON ELECTRICAL PLANS ARE CONTROLLERS, AND ASSOCIATED CONTROL DEVICES ARE FURNISHED UNDER OTHER DIVISIONS AND
APPROXIMATE; COORDINATE WITH ARCHITECTURAL AND MECHANICAL PLANS AND DETAILS, AND INSTALLED UNDER THIS DIVISION. COORDINATE INSTALLATION AND LOCATIONS WITH OTHER S WALL MOUNTED OCCUPANCY SENSOR WITH MANUAL OVERRIDE AND DIMMING
WITH JOB CONDITIONS. INSTALL SWITCHES WITH "OFF" POSITION DOWN. INSTALL RECEPTACLES DIVISION CONTRACTORS. E-202 PARTIAL SECOND FLOOR RCP - LIGHTING
WITH GROUNDING POLE IN THE UP POSITION FOR VERTICAL MOUNTING AND AT RIGHT FOR S WALL MOUNTED VACANCY SENSOR WITH MANUAL OVERRIDE AND DIMMING
HORIZONTAL MOUNTING. 2. POWER WIRING FROM THE INDICATED SOURCE TO THE STARTER/CONTROLLER/DRIVE UNIT, AND
FROM THE STARTER/CONTROLLER UNIT TO THE MOTOR, INCLUDING ANY LOCAL DISCONNECT E-501 PANEL SCHEDULES - ELECTRICAL
4. LOCATE AND INSTALL ELECTRICAL EQUIPMENT, JUNCTION AND PULL BOXES, PANELBOARDS, SWITCHES PROVIDED AND INSTALLED BY THIS DIVISION, AND ALL ASSOCIATED LUGS, TERMINALS, VS CEILING MOUNTED DUAL TECHNOLOGY BI-DIRECTIONAL VACANCY SENSOR
SWITCHES, CONTROLS, AND OTHER APPARATUS REQUIRING MAINTENANCE, INSPECTION, AND AND CONNECTIONS, IS THE WORK OF THIS DIVISION.
OPERATION SO AS TO BE READILY ACCESSIBLE. E-601 DETAILS - ELECTRICAL OS CEILING MOUNTED DUAL TECHNOLOGY BI-DIRECTIONAL OCCUPANCY SENSOR
3. CONTROL CIRCUIT WIRING IS GENERALLY FURNISHED AND INSTALLED UNDER OTHER DIVISIONS,
RACEWAY INSTALLATION: EXCEPT THAT ANY SUCH WIRING SHOWN ON ELECTRICAL DRAWINGS IS WORK OF THIS DIVISION.
OS WALL MOUNTED DUAL TECHNOLOGY OCCUPANCY SENSOR
E-602 DETAILS - ELECTRICAL
1. IN ALL ARCHITECTURALLY FINISHED SPACES, CONDUITS AND CABLES SHALL BE RUN CONCEALED IN 4. COOPERATE AND COORDINATE WITH THE OTHER TRADES IN THE INSTALLATION, CONNECTION, AND
HUNG OR FURRED CEILINGS, SLABS, MASONRY, AND PARTITIONS UNLESS OTHERWISE INDICATED. TESTING OF MECHANICAL EQUIPMENT. PERFORM WORK OF THIS SECTION IN ACCORDANCE WITH VS WALL MOUNTED DUAL TECHNOLOGY VACANCY SENSOR
SAW CUTTING AND FINISHED PATCHING SHALL BE REQUIRED IN EXISTING SLABS AND MASONRY EQUIPMENT MANUFACTURERS' INSTRUCTIONS.
WALLS. IN UNFINISHED SPACES, RACEWAYS MAY BE RUN EXPOSED. E-701 SPECIFICATIONS - ELECTRICAL
R BYPASS RELAY
COORDINATION DRAWINGS: REVISIONS
2. UNLESS OTHERWISE INDICATED, EXACT ROUTING OF RACEWAYS SHALL BE DETERMINED BY THE
CONTRACTOR TO SUIT PROJECT REQUIREMENTS AND FIELD CONDITIONS. 1. DEVELOP AND SUBMIT COORDINATION DRAWINGS AS OUTLINED. R DIMMING BYPASS RELAY NUMBER DATE DESCRIPTION

3. PROVIDE SEPARATE RACEWAYS, JUNCTION BOXES, PULL BOXES AND WIREWAYS FOR ALL A. SHEET METAL AND PLUMBING SHOP DRAWINGS THAT HAVE BEEN COORDINATED WITH J WALL MOUNTED JUNCTION BOX
EMERGENCY SYSTEM WIRING. ARCHITECTURAL AND STRUCTURAL DRAWINGS SHALL BE SUBMITTED TO ENGINEER FOR REVIEW.
DRAWINGS MUST BE RETURNED FROM ENGINEER EITHER "REVIEWED" OR "FURNISH AS CORRECTED"
ELECTRICAL ABBREVIATIONS
CEILING MOUNTED QUAD RECEPTACLE
WIRING INSTALLATION: PRIOR TO BEING USED AS BASIS FOR COORDINATION DRAWINGS.
A AMPERES J
1. DO NOT USE WIRE SMALLER THAN NO. 12 AWG FOR ANY POWER OR LIGHTING CIRCUIT. USE LARGER B. AFTER SHEET METAL AND PIPING DRAWINGS HAVE BEEN REVISED PER ENGINEERS COMMENTS, CEILING MOUNTED JUNCTION BOX FOR MOTORIZED DOOR OPERATOR
SIZES WHERE INDICATED, AS REQUIRED BY CODES, AND AS FOLLOWS: REPRODUCIBLE COPIES SHALL BE SENT TO THE TRADES IN THE FOLLOWING SEQUENCE FOR THE AFF ABOVE FINISHED FLOOR
INCLUSION OF THEIR WORK: DUPLEX CONVENIENCE RECEPTACLE - 18" AFF U.O.N.
30 AMPERE CIRCUIT: NO. 10 C CONDUIT
40 AMPERE CIRCUIT: NO. 8 -MECHANICAL SHEET METAL
QUAD CONVENIENCE RECEPTACLE - 18" AFF U.O.N.
50 AMPERE CIRCUIT: NO. 6 -PLUMBING PIPING C/B CIRCUIT BREAKER
60 AMPERE CIRCUIT: NO. 6 -MECHANICAL PIPING
-ELECTRICAL WORK CKT CIRCUIT DUPLEX CONVENIENCE RECEPTACLE - GROUND FAULT INTERRUPTING - 18" AFF U.O.N.
A. MINIMUM HOMERUN AND BRANCH CIRCUIT WIRING SIZES AND MAXIMUM HOMERUN CONDUIT FILL FOR

akPark
120 VOLT, 20 AMPERE CIRCUITS SHALL BE AS FOLLOWS: 2. AFTER ALL TRADES HAVE INCLUDED THEIR WORK ON THE COORDINATION DRAWING AND NOTED COP COPIER DUPLEX CONVENIENCE RECEPTACLE - GROUND FAULT INTERRUPTING - MOUNTED
CONFLICTS, ALL TRADES SHALL MEET TO RESOLVE CONFLICTS AND AGREE TO ACCEPTABLE ABOVE COUNTERTOP
CIRCUIT HOME RUN CONDUIT SIZE SOLUTIONS. EACH TRADE SHALL SIGN COORDINATION DRAWINGS. ITEMS NOT SHOWN ON E EXISTING
DUPLEX TELEVISION RECEPTACLE - 72" AFF U.O.N.
LENGTH WIRE SIZE WIRE SIZE (8 WIRES/CONDUIT) COORDINATION DRAWING IS RESPONSIBILITY OF OMITTING CONTRACTOR AND CONTRACTOR IS
SUBJECT TO ADDITIONAL COSTS INCURRED BY OTHER TRADES. E.C. ELECTRICAL CONTRACTOR Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

0' TO 50' #12 #12 3/4" DUPLEX REFRIGERATOR RECEPTACLE - 48" AFF U.O.N.
51' TO 100' #12 #10 3/4" 3. THE ARCHITECT AND ENGINEER ARE NOT PART OF THE COORDINATION DRAWING PROCESS. THE EM EMERGENCY
93 Lake Avenue, Danbury, CT 06810
101' TO 200' #10 #8 1" ENGINEER WILL PROVIDE ASSISTANCE FOR NOTED CONFLICTS ONLY. COORDINATION DRAWINGS 203.778.1017 F 203.778.1018
ER EXISTING RELOCATED SPECIAL RECEPTACLE CONFIGURATION - SEE NEMA #
ARE NOT TO BE CONSIDERED PIPING OR DUCT SHOP DRAWINGS. THE CONTRACTOR IS REQUIRED TO
GREATER THAN 200' - REQUEST DIRECTION FROM ARCHITECT. SUBMIT INDIVIDUAL PIPING AND DUCTWORK SHOP DRAWINGS FOR REVIEW BY THE ENGINEER. PIPING 171 Madison Avenue,
ETBR EXISTING TO BE RELOCATED PLUGMOLD SURFACE RACEWAY New York, NY 10016
AND DUCTWORK SHOP DRAWINGS SHALL FOLLOW THE DESIGN INTENT OF THE CONTRACT 212.695.2422 F 212.695.2423
NOTE: PROVIDE DERATING PER CODE WHEN INSTALLING MORE THAN 3 CURRENT CARRYING DOCUMENTS.
ETR EXISTING TO REMAIN www.kohlerronan.com
CONDUCTORS IN CONDUIT. NON-FUSED DISCONNECT E-mail [email protected]
4. SUBMIT FINAL SIGNED COORDINATION DRAWING TO ENGINEER FOR REVIEW. ENGINEER WILL REVIEW
FBO FURNISHED BY OTHERS
B. HOME RUNS AND BRANCH CIRCUIT WIRING FOR 277 VOLT, 20 AMPERE CIRCUITS SHALL BE AS COORDINATION DRAWINGS FOR GENERAL ARRANGEMENT AND FOR NOTED CONFLICTS ONLY.
FUSED BUS PLUG, RATING / FUSING
FOLLOWS: SPECIFIC INSTALLATION REQUIREMENTS WILL BE REVIEWED ONLY IN INDIVIDUAL TRADE SHOP G GROUND
DRAWINGS.

LENGTH
CIRCUIT
WIRE SIZE
HOME RUN
WIRE SIZE
CONDUIT SIZE
(8 WIRES/CONDUIT) 5. ANY WORK FABRICATED OR INSTALLED PRIOR TO SIGN OFF BY ALL TRADES WHICH IS DEEMED TO BE
HD HAND DRYER EMERGENCY POWER OFF BUTTON
MEDIA CENTER
0' TO 100' #12 #12 3/4"
IN CONFLICT WITH COORDINATION DRAWINGS SHALL BE REMOVED AND RE-INSTALLED IN
CONFORMANCE WITH COORDINATION DRAWINGS.
JB JUNCTION BOX F FIRE ALARM PULL STATION - 48"AFF U.O.N. RELOCATION TO
100' TO 200' #12 #10 3/4"
6. EACH CONTRACTOR (MENTIONED ABOVE) IS RESPONSIBLE FOR THE COORDINATION OF HIS
M/B MAIN BREAKER
FIRE ALARM HORN/STROBE - 80"AFF U.O.N. ELIHU BURRITT
GREATER THAN 200' - REQUEST DIRECTION FROM ARCHITECT. SUB-CONTRACTORS. MCB MAIN CIRCUIT BREAKER
FIRE ALARM STROBE LIGHT - 80"AFF U.O.N.
LIBRARY
NOTE: PROVIDE DERATING PER CODE WHEN INSTALLING MORE THAN 3 CURRENT CARRYING 7. THE OVERALL COORDINATION OF THE COORDINATION PROCESS IS THE RESPONSIBILITY OF THE MD MOTORIZED DOOR
CONDUCTORS IN CONDUIT. CONTRACTOR. THE ENGINEER IS NOT RESPONSIBLE FOR THE COORDINATION PROCESS. THE S SMOKE DETECTOR
ENGINEER WILL RESPOND TO QUESTIONS THAT ARISE FROM THE COORDINATION PROCESS. MLO MAIN LUG ONLY
2. DO NOT USE WIRE SMALLER THAN NO. 14 AWG FOR CONTROL CIRCUITS UNLESS OTHERWISE DRAWINGS SUBMITTED WILL BE REVIEWED FOR CLEARLY IDENTIFIED CONFLICTS ONLY. SOLUTIONS
RECOMMENDED BY THE EQUIPMENT OR SYSTEM MANUFACTURER ON WIRING SHOP DRAWINGS, AND TO CONFLICTS WILL NOT BEAR ADDITIONAL COST. MTD MOUNTED H HEAT DETECTOR, NUMBER INDICATES TEMPERATURE IN FAHRENHEIT
SO APPROVED BY THE ARCHITECT.
AS BUILT DRAWINGS OHD OVERHEAD FACP FIRE ALARM CONTROL PANEL
3. WHERE GREATER THAN THREE (3) CURRENT-CARRYING CONDUCTORS ARE INSTALLED IN ANY ONE
CONDUIT OR CABLE, CONDUCTORS MUST BE DERATED AND SIZES INCREASED, IF NEEDED, TO PNL PANEL
ACCOMMODATE CONDUCTOR DERATING AS REQUIRED BY NEC ARTICLE 310. 1. PROVIDE A COMPLETE SET OF AS-BUILT DRAWINGS REFLECTING AS INSTALLED CONDITIONS. SURFACE MTD PANELBOARD AND CLEARANCE
AS-BUILT DRAWINGS SHALL INDICATE ALL INSTALLED CONDITIONS OF SYSTEMS WITHIN THIS TP TRAP PRIMER
4. CONDUCTORS SHALL BE COMPLETELY INSTALLED AND CONNECTED. PROVIDE ALL TERMINALS, LUGS, DISCIPLINE. DRAWINGS SHALL BE OF SIMILAR SCALE AS THE CONSTRUCTION DOCUMENTS AND X/# BRANCH CIRCUIT HOMERUN (X = PANEL BOARD, # = CIRCUIT NO.)
AND CONNECTORS TO SUIT THE APPLICATION, AND IN COMPLIANCE WITH EQUIPMENT INCLUDE DETAILS AS NECESSARY TO CLEARLY REFLECT THE INSTALLED CONDITION. DRAWINGS U.O.N. UNLESS OTHERWISE NOTED
MANUFACTURERS' RECOMMENDATIONS. SHALL BE BOUND IN A COMPLETE AND CONSECUTIVE SET. SUPPLEMENTAL SKETCHES AND LOOSE
PAPERWORK WILL NOT BE ACCEPTABLE AND WILL BE RETURNED FOR REVISION. THE CONTRACTOR V VOLTS
5. UNDER NO CIRCUMSTANCES SHALL ANY SWITCH OR CIRCUIT BREAKER BREAK A NEUTRAL SHALL COMPLY WITH THE ENGINEERS COMMENTS TO PRODUCE A CLEAR AND CONCISE SET OF
CONDUCTOR. DRAWINGS. DRAWINGS SHALL BE SUBMITTED IN BOTH HARD COPY AND ELECTRONIC (AUTO-CAD VA VOLT-AMPERES
VERSION AS REQUIRED BY THE OWNER) VERSION. NUMBER OF COPIES OF EACH AS REQUESTED BY
6. THE CIRCUIT NUMBERS INDICATED ON THE DRAWINGS ARE INTENDED AS A GUIDE FOR PROPER THE OWNER.
N
CONNECTION OF CIRCUITS AT PANELS. HOWEVER, IT SHALL BE THE RESPONSIBILITY OF THE
CONTRACTOR TO ENSURE THAT THE FINAL CIRCUITING WORK FULFILLS THE FOLLOWING
CONDITIONS:
2. PROVIDE "AS-BUILT DRAWINGS" INDICATING IN A NEAT AND ACCURATE MANNER A COMPLETE
RECORD OF ALL REVISIONS OF THE ORIGINAL DESIGN OF THE WORK. INDICATE THE FOLLOWING
KEY PLAN W E

INSTALLED CONDITIONS: S
A. LOADS ON PANEL BUSSES SHALL BE PHASE-BALANCED AS EVENLY AS POSSIBLE.

7. PROVIDE SEPARATE NEUTRALS FOR EACH CIRCUIT. WHERE MULTIPLE CIRCUITS ARE INSTALLED IN A. INCLUDE ALL CHANGES AND AN ACCURATE RECORD, ON REPRODUCTIONS OF THE CONTRACT
THE SAME RACEWAY OR ENCLOSURE, IDENTIFY NEUTRALS WITH CORRESPONDING BRANCH CIRCUIT DRAWINGS OR APPROPRIATE SHOP DRAWINGS, OF ALL DEVIATIONS, BETWEEN THE WORK SHOWN
PHASE CONDUCTOR NUMBERS. AND WORK INSTALLED.

GROUNDING INSTALLATION:
B. EQUIPMENT LOCATIONS (EXPOSED AND CONCEALED), DIMENSIONED FROM PROMINENT BUILDING
1. EQUIPMENT GROUNDING LINES.

A. INSTALL AN INSULATED GROUND CONDUCTOR, RUN IN THE RACEWAY WITH THE PHASE C. APPROVED SUBSTITUTIONS, CONTRACT MODIFICATIONS, AND ACTUAL EQUIPMENT AND MATERIALS
CONDUCTORS, FOR EACH FEEDER SERVING: PANELBOARDS, LIGHTING DIMMER BOARDS, MOTOR INSTALLED.
CONTROL CENTERS, MOTORS, EQUIPMENT AND APPLIANCES UNLESS OTHERWISE NOTED.

B. INCLUDE AN INSULATED GROUND CONDUCTOR IN ALL CONDUIT RUNS CONTAINING SECTIONS OF D. CONTRACT MODIFICATIONS, ACTUAL EQUIPMENT AND MATERIALS INSTALLED.
FLEXIBLE CONDUIT UNLESS OTHERWISE NOTED.
E. SUBMIT FOR REVIEW BOUND SETS OF THE REQUIRED DRAWINGS, MANUALS AND OPERATING
C. INCLUDE AN INSULATED GROUND CONDUCTOR IN ALL BRANCH CIRCUIT RACEWAYS OR CABLES INSTRUCTIONS.
UNLESS OTHERWISE NOTED.

F. SUBMIT A COMPLETE MAINTENANCE MANUAL OF ALL EQUIPMENT INSTALLED UNDER THIS CONTRACT.
COVER SHEET -
ELECTRICAL

22 E-001
 DEMOLITION AND REMOVALS LIGHT FIXTURE NOTES LIGHTING FIXTURE SCHEDULE
TYPE LAMP VOLTAGE MOUNTING DESCRIPTION
1. REFER TO ARCHITECTURAL REFLECTED CEILING PLANS AND INTERIOR ELEVATIONS FOR EXACT
1. THE EXISTING FACILITY WILL BE OCCUPIED AND IN OPERATION DURING THE PERFORMANCE OF THE
LOCATIONS AND MOUNTING HEIGHTS OF ALL LIGHT FIXTURES. EDGE LIT LED EXIT SIGN WITH ALUMINUM HOUSING, DOUBLE FACE, RED
WORK.
CEILING LETTER COLOR ON MIRROR BACKGROUND, AND EMERGENCY BATTERY
2. THE ELECTRICAL CONTRACTOR SHALL VERIFY ALL CEILING TYPES AND/OR COORDINATE ALL FIXTURE LED 120/277V BACKUP
2. WHEN NECESSARY TO TEMPORARILY DISCONNECT ANY EXISTING FEEDER OR BRANCH CIRCUIT RECESSED
TRIMS PRIOR TO PURCHASE OF FIXTURES. LITHONIA LIGHTING #EDGR
SUPPLYING OCCUPIED FACILITIES, CONFER WITH THE OWNER, AND SCHEDULE A MUTUALLY
AGREEABLE PERIOD OF INTERRUPTION.
3. ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL ALL LIGHT FIXTURES COMPLETE WITH EDGE LIT LED EXIT SIGN WITH ALUMINUM HOUSING, SINGLE FACE, RED
MOUNTING HARDWARE AND LAMPS. WALL LETTER COLOR ON MIRROR BACKGROUND, AND EMERGENCY BATTERY
3. WHERE REPLACEMENT, RELOCATION OR MODIFICATION OF EXISTING EQUIPMENT IS INDICATED,
PROVIDE AND MAINTAIN ALL TEMPORARY FEEDERS, CONNECTIONS, CIRCUIT PROTECTION, AND ANY LED 120/277V RECESSED BACKUP
OTHER MATERIALS AND APPURTENANCES REQUIRED TO MAINTAIN SERVICES TO OCCUPIED AREAS. LITHONIA LIGHTING #EDGR

4. NO WORK SHALL BE LEFT INCOMPLETE, NOR ANY HAZARDOUS SITUATION CREATED, WHICH WILL 2' X 2' LED TROFFER, 3200 LUMENS, 3500K COLOR TEMPERATURE, 0-10V
AFFECT THE LIFE OR SAFETY OF THE PUBLIC AND/OR BUILDING OCCUPANTS. AT NO TIME SHALL THE CEILING DIMMING
WORK INTERFERE WITH OR CUT OFF ANY OF THE EXISTING SERVICES WITHOUT THE OWNER'S PRIOR LIGHTING CONTROL NOTES A 28W LED 120/277V RECESSED -
VISIONEERING #LRTZ
WRITTEN PERMISSION.

5. THE OWNER RESERVES THE RIGHT TO OPERATE ALL EXISTING ELECTRICAL AND MECHANICAL 2' X 2' LED TROFFER, 3200 LUMENS, 3500K COLOR TEMPERATURE, 0-10V
1. WHERE MULTIPLE OCCUPANCY/VACANCY SENSORS ARE INDICATED IN A SPACE, THE DETECTION OF
EQUIPMENT NOT INCLUDED IN THIS WORK, AND TO PERFORM ALL REQUIRED SERVICING AND REPAIRS CEILING DIMMING
PRESENCE BY ANY OCCUPANCY/VACANCY SENSOR SHALL ENERGIZE ALL LIGHTING FIXTURES WITHIN B 28W LED 120/277V
TO SAME, AT ALL TIMES. SURFACE -
THE GIVEN SPACE U.O.N.
VISIONEERING #LSTZ
6. IT IS REQUIRED THAT THE WORK INDICATED AND/OR SPECIFIED SHALL BE CARRIED OUT WITH A
MINIMUM OF INTERFERENCE TO THE ESTABLISHED OPERATIONS OF THE BUILDING. 4" LED DOWNLIGHT, 1100 LUMENS, 3500K COLOR TEMPERATURE, 0-10V
CEILING DIMMING, WHITE TRIM, CLEAR REFLECTOR
7. REMOVE, ABANDON, REROUTE, OR RELOCATE ANY CONDUIT, WIRING, LIGHTING FIXTURES, OUTLETS, C 15W LED 120/277V RECESSED -
AND OTHER ELECTRICAL ITEMS, WHICH ARE LAID BARE IN THE COURSE OF, OR INTERFERE WITH, THE PRESCOLITE LITEFRAME #LF4LEDG4
ALTERATIONS. REMOVE ALL EXPOSED OUTLETS, CONDUIT, AND BRANCH CIRCUIT WORK, WHICH
INTERFERE WITH THE ALTERATIONS. 2' X 2' LED TROFFER, 3200 LUMENS, 3500K COLOR TEMPERATURE, 0-10V
CEILING DIMMING, BLACK PAINTED EXTERIOR HOUSING
8. IT IS THE INTENTION OF THESE SPECIFICATIONS TO PROVIDE FOR THE CONTINUANCE OF ALL D 28W LED 120/277V SURFACE -
ELECTRICAL SERVICES PRESENTLY INSTALLED IN THE UNALTERED AREAS. PROVIDE ALL CONDUIT, VISIONEERING #LSTZ
WIRING, AND DEVICES NECESSARY TO MAINTAIN SERVICES TO THESE AREAS.
2' UNDER CABINET FIXTURE, 1200 LUMENS, 3500K COLOR TEMPERATURE, #12
9. COMPARE THE PLANS WITH THE EXISTING CONDITIONS TO DETERMINE THE AMOUNT OF WORK UNDER PATTERN FROSTED ACRYLIC SHIELDING, NON-DIMMING DRIVER
E 21W LED 120/277V
AFFECTED. REMOVE ALL UNUSED EXPOSED CIRCUIT WORK, OUTLETS, FIXTURES AND THE LIKE NOT
REQUIRED BY THE ALTERATIONS.
CABINET -
H.E. WILLIAMS #1SF
REVISIONS
NUMBER DATE DESCRIPTION
10. ALL MATERIALS REQUIRED TO BE REMOVED AND NOT REINSTALLED UNDER THIS DIVISION OF THE
WORK, UNLESS OTHERWISE INDICATED, SHALL BECOME THE PROPERTY OF THE CONTRACTOR, AND
SHALL BE REMOVED FROM THE SITE.

11. WHERE FEEDERS AND BRANCH CIRCUITS OR DEVICES AND EQUIPMENT ARE INDICATED TO BE
REMOVED, CONDUCTORS AND CABLES SHALL BE COMPLETELY REMOVED BACK TO THEIR SOURCE.
EXPOSED OR ACCESSIBLE CONDUITS SHALL BE REMOVED COMPLETELY; CONDUITS EMBEDDED IN
CONCRETE OR MASONRY SHALL BE CUT OFF FLUSH AND THE SURFACE PATCHED SMOOTH AND
LEVEL.

12. REMOVED MATERIALS SHALL BE DISPOSED OF USING LICENSED CARTING SERVICE.

13. HAZARDOUS MATERIALS - CONTAINING PCB'S (BALLASTS), AND THE LIKE SHALL BE DISPOSED OF BY
AN EPA APPROVED, LICENSED DISPOSAL SERVICE. CONTRACTOR SHALL OBTAIN AND HAVE ON FILE,
AFFIDAVIT, AND RECEIPTS STATING HOW AND WHERE THE WASTE WAS DISPOSED OF OR

akPark
CONVERTED.

14. CONTRACTOR SHALL REMOVE ALL ELECTRICAL EQUIPMENT IN OR ON WALLS THAT ARE TO BE
REMOVED - MAINTAIN CONTINUITY OF ALL EXISTING BRANCH CIRCUITRY TO EXISTING ROOMS NOT
BEING RENOVATED. REWIRE ALL EXISTING BRANCH CIRCUITS (THAT ARE TO REMAIN) AS REQUIRED. Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

REFER TO ARCHITECTURAL DEMOLITION DRAWINGS FOR WALLS BEING REMOVED - REFER TO
CONSTRUCTION SCHEDULE FOR TIME DELAY.
93 Lake Avenue, Danbury, CT 06810
203.778.1017 F 203.778.1018
15. CONDUIT IN EXISTING OR NEW CEILINGS THAT IS NOT INTENDED FOR REUSE SHALL BE REMOVED
BACK TO THE PANEL FROM WHICH IT ORIGINATES. 171 Madison Avenue,
New York, NY 10016
212.695.2422 F 212.695.2423
16. CONDUCTORS THAT ARE NOT DEEMED REUSABLE SHALL BE REMOVED BACK TO THE NEAREST
JUNCTION BOX. WHERE THE ENTIRE CIRCUIT IS TO BE REMOVED, THE CONDUCTORS SHALL BE www.kohlerronan.com
REMOVED BACK TO THE PANELBOARD FROM WHICH THEY ORIGINATE. E-mail [email protected]

17. OUTAGES OF EXISTING ELECTRICAL (LIGHTING, POWER, AND SIGNAL) SYSTEMS NECESSITATED BY
WORK OF ALL TRADES SHALL BE IN ACCORDANCE WITH FIELD SCHEDULES BY THE GENERAL
CONTRACTOR AND OWNER - INCLUDE ALL ELECTRIC WORK OVERTIME AND SUPERVISION TO COMPLY
- CONTRACTOR SHALL OBTAIN OWNER'S GENERAL CONTRACTOR'S APPROVAL PRIOR TO DISRUPTING MEDIA CENTER
EXISTING ELECTRICAL SYSTEM.
RELOCATION TO
18. CONTRACTOR TO MAINTAIN CONTINUITY AND ACCESSIBILITY OF ALL EXISTING SYSTEMS AND SYSTEM
EQUIPMENT FEEDERS WHICH MAY BE DISRUPTED FOR WORK OF ANY TRADE. ELIHU BURRITT
19. CONTRACTOR TO MAINTAIN CONTINUITY AND ACCESSIBILITY OF ALL EXISTING ELECTRICAL (POWER,
LIBRARY
LIGHTING, AND SIGNAL) SYSTEMS, EQUIPMENT FEEDERS AND BRANCH CIRCUITS ON FLOORS OR
AREAS THAT ARE NOT AFFECTED BY DEMOLITION OR NEW CONSTRUCTION - REFER TO
CONSTRUCTION SCHEDULE FOR ADDITIONAL INFORMATION.

20. ANY EXISTING ELECTRICAL WORK WHICH IS PULLED OUT OR CUT AWAY SHALL BE REMOVED FROM
THE SITE AS DIRECTED BY THE GENERAL CONTRACTOR AND THE OWNER.

21. EXISTING ELECTRICAL EQUIPMENTS WHICH IS NOT TO BE REUSED SHALL BE REMOVED FROM
DRYWALL PARTITIONS. ANY OPENING IN EXISTING PARTITIONS LEFT BY REMOVAL OF EXISTING
ELECTRICAL EQUIPMENT SHALL BE PATCHED BY THIS CONTRACTOR WITH MATERIALS TO MATCH
EXISTING.

22. FOR PURPOSES OF THE CONTRACT, WHAT IS NOTED OR SHOWN ON DRAWINGS INDICATES THE
SCOPE OF WORK REQUIRED AND QUALITY OF MATERIALS REQUIRED.

23. CONTRACTOR TO EXAMINE ALL CONTRACT DOCUMENTS AND PERFORM ALL DEMOLITION BOTH FOR
AREAS BEING RENOVATED AND FOR AREAS WHICH MUST BE REWORKED TO PERMIT THE
INSTALLATION OF WORK BY THE VARIOUS TRADES.

24. CONTRACTOR SHALL VISIT THE SITE AND VERIFY THE EXTENT OF DEMOLITION AND REMOVALS PRIOR N
TO THE SUBMISSION OF BIDS. NO CONSIDERATION SHALL BE GIVEN FOR FAILURE TO VISIT THE SITE.
KEY PLAN W E
25. CONTRACTOR SHALL UTILIZE ALL THE BREAKERS IN THE EXISTING PANELS THAT BECOME AVAILABLE
WHEN BRANCH CIRCUITS ASSOCIATED WITH THEM ARE DISCONNECTED AND REMOVED DUE TO S
DEMOLITION OF THE ELECTRICAL WORK.

22 E-002
 DEMOLITION NOTES DEMOLITION KEY NOTES

1. ALL DEVICES SHOWN WITHIN SCOPE BOUNDARY LINES ARE TO BE COMPLETELY REMOVED, U.O.N. 1 REFER TO ARCHITECTURAL DRAWINGS FOR EXACT EXTENT OF DEMOLITION WORK.

2. EVERY EFFORT HAS BEEN MADE TO IDENTIFY LOCATIONS OF DEVICES TO BE REMOVED, HOWEVER, DISCONNECT AND REMOVE ALL EXISTING INTERIOR LIGHTING FIXTURES, SWITCHES, BACKBOXES,
NOT ALL DEVICES MAY HAVE BEEN LOCATED. ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR
2 CONDUIT AND WIRING BACK TO PANEL (TYPICAL FOR ALL AREAS).
REMOVAL OF ALL DEVICES WITHIN SCOPE BOUNDARY LINES.
DISCONNECT AND REMOVE ALL EXISTING RECEPTACLES, PLUGMOLD, SURFACE RACEWAY,
3 BACKBOXES, CONDUIT AND WIRING BACK TO PANEL (TYPICAL FOR ALL AREAS).

DISCONNECT AND REMOVE ALL EXISTING TELEPHONE/DATA OUTLETS, JUNCTION BOXES,

4 RACEWAYS AND WIRING BACK TO TELECOMMUNICATIONS BACKBOARD - ALL TEL/COM WIRING
REMOVED BY E.C. (TYPICAL FOR ALL AREAS). COORDINATE CABLE REMOVAL WITH OWNER.

DISCONNECT AND REMOVE ALL FINAL CONNECTIONS, DISCONNECT SWITCHES, OUTLETS,

5 BACKBOXES, CONDUIT AND WIRING FOR OWNER'S EQUIPMENT BACK TO RESPECTIVE PANEL
(TYPICAL FOR ALL EQUIPMENT TO BE REMOVED).

DISCONNECT AND REMOVE ALL FINAL CONNECTIONS, DISCONNECT SWITCHES, OUTLETS,

6 CONDUIT AND WIRING FOR HVAC EQUIPMENT BACK TO PANEL (TYPICAL FOR ALL EQUIPMENT TO
BE REMOVED).

DISCONNECT AND REMOVE ALL FINAL CONNECTIONS, DISCONNECT SWITCHES, OUTLETS,

7 CONDUIT AND WIRING FOR PLUMBING EQUIPMENT BACK TO PANEL (TYPICAL FOR ALL EQUIPMENT
TO BE REMOVED).

DISCONNECT AND REMOVE ALL EXISTING HARDWIRED FIRE ALARM DEVICES, BACKBOXES,
8 CONDUIT AND WIRING BACK TO RESPECTIVE FIRE ALARM TERMINAL CABINET, U.O.N. (TYPICAL FOR
ALL AREAS).

ELECTRICAL CONTRACTOR SHALL MAINTAIN/RECONNECT ALL EXISTING BRANCH CIRCUIT WIRING

9 DISTURBED DURING CONSTRUCTION BUT OUTSIDE OF NEW CONSTRUCTION AREA.

DISCONNECT AND REMOVE EXISTING PANELBOARD PP-2FN AND FEEDER CONDUIT AND CABLE
10 BACK TO SOURCE.
REVISIONS
2 NUMBER DATE DESCRIPTION
1 3
5
4 6
8
7 9
2
1 3
5
4 6
8
7 9

S
S

S
akPark
Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

S S S
93 Lake Avenue, Danbury, CT 06810
203.778.1017 F 203.778.1018

171 Madison Avenue,

New York, NY 10016
S 212.695.2422 F 212.695.2423
S S www.kohlerronan.com
10 E-mail [email protected]

MEDIA CENTER
SS S RELOCATION TO
PP-2FN
ELIHU BURRITT
ETR
ETBR
LIBRARY
ETR ETR

1 PARTIAL SECOND FLOOR DEMOLITION PLAN

ED-102 SCALE: 1/8" - 1'-0"

KEY PLAN W E

22
 LA1/48 LA1/43,45 LA1/44,46 LA1/47,49

48 REVISIONS
ACCU-3
ACCU-1 ACCU-2 NUMBER DATE DESCRIPTION

akPark
Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

ETR

93 Lake Avenue, Danbury, CT 06810

203.778.1017 F 203.778.1018

171 Madison Avenue,

New York, NY 10016
212.695.2422 F 212.695.2423

www.kohlerronan.com
E-mail [email protected]

MEDIA CENTER
RELOCATION TO
ELIHU BURRITT
LIBRARY

LA (ETR)

TX (ETR) LA1 (ETR)

MDP (ETR) LDP (ETR)

KEY PLAN W E

S
1 PARTIAL FIRST FLOOR PLAN
E-101 SCALE: 1/8" - 1'-0"

PARTIAL FIRST
FLOOR PLAN -
ELECTRICAL

22 E-101
 NOTES

1. E.C. SHALL MODIFY AND REPROGRAM FIRE ALARM SYSTEM TO ACCEPT NEW DEVICES AS NECESSARY.

2. E.C. SHALL COORDINATE ALL ELECTRICAL REQUIREMENTS WITH "DNR" AND SUPERTECH" VENDORS.

DEMOLITION KEY NOTES

DISCONNECT AND REMOVE EXISTING PANELBOARD PPS4, TRANSFORMER, DISCONNECT

1
SWITCHES, AND ALL ASSOCIATED FEEDER CONDUIT AND CABLE BACK TO EXISTING BUSWAY.
EXISTING BRANCH CIRCUITS SHALL BE RECONNECTED TO NEW PANELBOARD PPS4 LOCATED ON
DETAIL 4/E-102.

SURFACE MTD SURFACE MTD SURFACE MTD PP-2FN/13

PP-2FN/26

PP-2FN/9 PP-2FN/27 28
PP-2FN/46
REVISIONS
SURFACE MTD 12 12 13 13
PP-2FN/28 31 NUMBER DATE DESCRIPTION
PP-2FN/10 13 PP-2FN/21 SURFACE MTD
27 PP-2FN/11
9 PP-2FN/12 AUDIO BOOTH
ENGINEER
21 PP-2FN/31
27 27 OFFICE
28 GREEN RM. 12 LOCATE ABOVE DOOR HEIGHT POWER TO VRF
OFFICE PP-2FN/14
OFFICE AUDIO BOOTH 47 OFFICE OFFICE 40 PP-2FN/56 CONTROLLER
TALENT AC-3 AC-4
9 10 39 39 40
11 11 14 S SURFACE MTD
27
12 14 52,54 52,54 PP-2FN/58
PP-2FN/6 31 PP-2FN/39 PP-2FN/40
FUTURE EXPANSION
CLASSROOM/ 39 53,55 53,55 40
9 6 PP-2FN/7 J 31 TV STUDIO A
SURFACE MTD PP-2FN/47 S S
PP-2FN/8 46 43
S PP-2FN/4 PP-2FN/5 PP-2FN/52,54
PP-2FN/49 PP-2FN/29 PP-2FN/45 44 SURFACE MTD
S S PP-2FN/48 S

AC-5
CORRIDOR AC-2 PP-2FN/53,55 59 59 59 53,55 PP-2FN/43 PP-2FN/42
STAIR #3
35 GRAPHIC DESIGN
STAIR #1 36 ENGINEERING
EF-1 32 WORKBENCH
PP-2FN/30 PP-2FN/59

akPark
PP-2FN/32 PP-2FN/44
PP-2FN/2 H
LACTATION RACK RM. 29 PROVIDE (4) STACKED
ROOM
CONTROL RM. EQUIPMENT PP-2FN/51
SURFACE MTD S 33 DISTRIBUTION
MEN'S PP-2FN/50

PP-2FN/1
2 6 6 PP-2FN/33
30
PP-2FN/35
CORR. 41 41 41 41 41 PP-2FN/41 SURFACE MTD Architects LLC

AC-8
WOMEN'S 312 Park Rd, W. Hartford, CT (860)232-6664
J 53,55 PP-2FN/38 PP-2FN/37
2 S
2 PP-2FN/34 35 93 Lake Avenue, Danbury, CT 06810
2 2 36 HC-1 S 44 203.778.1017 F 203.778.1018
F
36 38 37
PP-2FN/3 171 Madison Avenue,
SF-1 New York, NY 10016
SURFACE MTD 212.695.2422 F 212.695.2423
ETR SURFACE MTD
ALCOVE www.kohlerronan.com
ER E-mail [email protected]
2
CIRCULATION E-102

CONDUITS FROM DIMMING RACK TO STUDIO 2070900,

PROVIDE (5) 4" CONDUITS,COORDINATE WITH
MEDIA CENTER
STUDIO LIGHTING VENDOR RELOCATION TO
ELIHU BURRITT
LIBRARY
1 PARTIAL SECOND FLOOR PLAN
E-102 SCALE: 1/8" - 1'-0"

POWERED FROM ACCU-1

POWER TO VRF S
CONTROLLER AC-1
MTD TO LADDER RACK,
REFER TO DETAIL 2/E-601 (TYP OF 5)

PP-2FN/15 PP-2FN/25
PP-2FN/57
1 N
PP-2FN/16 1 1
RACK RM. TX-1 KEY PLAN W E

PP-2FN/17
PPS4
S
PPS4
S
25 LP-2 (ETR) LP-2 (ETR)
PP-2FN/18 1
PP-2FN/23
PP-2FN/19 800A BUSWAY (ETR) 800A BUSWAY (ETR)

PP-2FN/20,22,24

PP-2FN
23
J

POWER TO DIMMING RACK

PARTIAL SECOND
2 RACK RM. 2070500 PART PLAN 3 PARTIAL THIRD FLOOR DEMOLITION PART PLAN 4 PARTIAL THIRD FLOOR PART PLAN FLOOR PLAN -
E-102 SCALE: 1/4" - 1'-0" E-102 SCALE: 1/8" - 1'-0" E-102 SCALE: 1/8" - 1'-0"
ELECTRICAL

22 E-102
 A A A A A A A A
A A D D D
LP-2/26
26 26 26 26 26 26 26 26
26 26 OFFICE OFFICE GREEN RM.
AUDIO BOOTH AUDIO BOOTH
ENGINEER TALENT 26d 26d 26d
OFFICE A A A A A A A A OFFICE OFFICE
B B B B B B
A A 26 26 D D D LP-2/28
26 26 26 26 26 26
VS S
S S S S 28 28 28 28 28 28
FUTURE EXPANSION
26 26 A A A
A A A A 26d 26d 26d GRAPHIC DESIGN
OS CLASSROOM/ S S B
TV STUDIO A
26a 26b 26b 26b
26a 26a OS 26 26a B B B B B B
A A CORRIDOR
26 S D D D 28
C C S VS STAIR #3
STAIR #1 A A A VS 26 A A ENGINEERING
WORKBENCH
26a 26a A A 26
28 28 28c 28c 28c 28c
26 26 26d 26d 26d B
A VS EQUIPMENT
OS 26 26 26a 26 26 COORDINATE LIGHTING CONTROL S DISTRIBUTION
OS
A A 26 26
CONTROL RM. WITH STUDIO LIGHTING VENDOR CORR. 28
A OS A 26a RACK RM.
VS VS
LACTATION D D D B B B B SOFFIT MTD
26 WOMEN'S
26 MEN'S
ROOM
OS A A A B B
A A A B
VS
A A A 26 A 26 E 26d 26d 26d 28c 28c 28c 28c
28c
26a 26b 26a 26 26 28
26 26 26
S 26 26 26 S S S S
26
S REVISIONS
26 S
28 NUMBER DATE DESCRIPTION
E.C. SHALL ENERGIZE FIXTURE SURFACE MOUNTED
ALCOVE
FROM ALCOVE BRANCH CIRCUIT

CIRCULATION ETR ETR

1 PARTIAL SECOND FLOOR RCP

E-202 SCALE: 1/8" - 1'-0"
akPark
Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

93 Lake Avenue, Danbury, CT 06810

203.778.1017 F 203.778.1018

171 Madison Avenue,

New York, NY 10016
212.695.2422 F 212.695.2423

www.kohlerronan.com
E-mail [email protected]

MEDIA CENTER
RELOCATION TO
ELIHU BURRITT
LIBRARY

KEY PLAN W E

PARTIAL SECOND
FLOOR RCP
- LIGHTING

22 E-202
 480/277V, 3 PHASE, 4 WIRE 208/120V, 3 PHASE, 4 WIRE 400A MLO
LP-2 (ETR) 14,000 A.I.C. PP-2FN 400A BUS

LOAD IN VOLT-AMPERES LOAD IN VOLT-AMPERES

POLE

POLE

POLE

POLE
TRIP

TRIP

TRIP

TRIP
LOAD SERVED WIRE & CONDUIT WIRE & CONDUIT LOAD SERVED LOAD SERVED WIRE & CONDUIT WIRE & CONDUIT LOAD SERVED

1 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 2 1 2060100 HAND DRYER 2 #12+G -3/4"C. 20 1 1500 1500 1 20 2 #12+G -3/4"C. 2060200 HAND DRYER 2
3 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 4 3 2060100 RECEP 2 #12+G -3/4"C. 20 1 900 1200 1 20 2 #12+G -3/4"C. 2070000 COPIER RECEP 4
5 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 6 5 2070000 SHEDDER RECEP 2 #12+G -3/4"C. 20 1 500 720 1 20 2 #12+G -3/4"C. 2070000 RECEP 6
7 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 8 7 MOTORIZED DOOR 2 #12+G -3/4"C. 20 1 1000 1000 1 20 2 #12+G -3/4"C. 2070400 REFRIGERATOR 8
9 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 10 9 2070100 RECEP 2 #12+G -3/4"C. 20 1 720 540 1 20 2 #12+G -3/4"C. 2070200 RECEP 10
11 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 12 11 2070300 RECEP 2 #12+G -3/4"C. 20 1 900 720 1 20 2 #12+G -3/4"C. 2070400 RECEP 12
13 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 14 13 2070700 RECEP 2 #12+G -3/4"C. 20 1 1080 900 1 20 2 #12+G -3/4"C. 2070700 RECEP 14
15 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 16 15 2070500 RACK RECEP 2 #12+G -3/4"C. 20 1 750 750 1 20 2 #12+G -3/4"C. 2070500 RACK RECEP 16
17 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 18 17 2070500 RACK RECEP 2 #12+G -3/4"C. 20 1 750 750 1 20 2 #12+G -3/4"C. 2070500 RACK RECEP 18
19 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 20 19 2070500 RACK RECEP 2 #12+G -3/4"C. 20 1 750 20
21 EXISTING LOAD EXISTING 20 1 1 20 EXISTING EXISTING LOAD 22 21 2070800 RECEP 2 #12+G -3/4"C. 20 1 540 3 200 4 #3/0+#6G -2"C. 2070500 DIMMING RACK 22
23 EXISTING LOAD EXISTING 20 1 1950 1 20 2 #12+G -3/4"C. LIGHTING 2ND FLOOR 24 23 2070500 RECEP 2 #12+G -3/4"C. 20 1 360 24
25 EXISTING LOAD EXISTING 20 1 605 1 20 2 #12+G -3/4"C. LIGHTING 2ND FLOOR 26 25 2070500 RECEP 2 #12+G -3/4"C. 20 1 540 900 1 20 2 #12+G -3/4"C. 2070100 RECEP 26
27 EXISTING LOAD EXISTING 20 1 1 20 - SPACE 28 27 2070200 RECEP 2 #12+G -3/4"C. 20 1 900 900 1 20 2 #12+G -3/4"C. 2070300 RECEP 28
LOAD PER PHASE 605 # 1,950 29 2070600 RECEP 2 #12+G -3/4"C. 20 1 540 540 1 20 2 #12+G -3/4"C. 2070900 RECEP 30
SURFACE MTD NEMA 1
TOTAL = 2,555 VA 31 2070900 RECEP 2 #12+G -3/4"C. 20 1 1080 540 1 20 2 #12+G -3/4"C. 2070600 RECEP 32
33 2070600 RECEP 2 #12+G -3/4"C. 20 1 540 360 1 20 2 #12+G -3/4"C. 2070600 RECEP 34
35 2070900 RECEP 2 #12+G -3/4"C. 20 1 1080 720 1 20 2 #12+G -3/4"C. 0030400 RECEP 36
37 0030400 RECEP 2 #12+G -3/4"C. 20 1 720 720 1 20 2 #12+G -3/4"C. 0030400 RECEP 38
208/120V, 3 PHASE, 4 WIRE 500A MCB
14,000 A.I.C. PPS4 600A BUS 39 0030500 RECEP 2 #12+G -3/4"C. 20 1 900 900 1 20 2 #12+G -3/4"C. 0030600 RECEP 40 REVISIONS
41 0030400 RECEP 2 #12+G -3/4"C. 20 1 540 180 1 20 2 #12+G -3/4"C. 0030401 RECEP 42 NUMBER DATE DESCRIPTION
LOAD IN VOLT-AMPERES

POLE

POLE
TRIP

TRIP
LOAD SERVED WIRE & CONDUIT WIRE & CONDUIT LOAD SERVED 43 0030401 RECEP 2 #12+G -3/4"C. 20 1 360 540 1 20 2 #12+G -3/4"C. 0030401 RECEP 44
45 0030300 RECEP 2 #12+G -3/4"C. 20 1 1300 360 1 20 2 #12+G -3/4"C. 0030300 RECEP 46
1 2
47 0030300 RECEP 2 #12+G -3/4"C. 20 1 720 720 1 20 2 #12+G -3/4"C. 0030300 RECEP 48
4#600 KCMIL + #3G
3 EXISTING LOAD EXISTING 100 3 3 400 PP-2FN 4
IN 4" C 49 EF-1 2 #12+G -3/4"C. 20 1 180 72 1 20 2 #12+G -3/4"C. SF-1 50
5 6
51 HC-1 2 #10+G -3/4"C. 30 1 2500 313 52
7 1 20 EXISTING EXISTING LOAD 8 2 20 2 #12+G -3/4"C. AC-2 / AC-3 / AC-4
EXISTING LOAD EXISTING 20 2 53 AC-5 / AC-6 / AC-7 / 208 313 54
9 1 20 EXISTING EXISTING LOAD 10 2 #12+G -3/4"C. 20 2
55 AC-8 / AC-9 208 180 1 20 2 #12+G -3/4"C. VRF CONTROLLER 56
11 1 20 EXISTING EXISTING LOAD 12
EXISTING LOAD EXISTING 20 2 57 VRF CONTROLLER 2 #12+G -3/4"C. 20 1 180 360 1 20 2 #12+G -3/4"C. 0030300 RECEP 58
13 1 20 EXISTING EXISTING LOAD 14
59 0030400 RECEP 2 #12+G -3/4"C. 20 1 720 1 20 - SPARE 60
15 1 20 EXISTING EXISTING LOAD 16
17
19
EXISTING LOAD

SPARE
EXISTING

-
20

20
2

1
1
1
20
20
EXISTING
EXISTING
EXISTING LOAD
EXISTING LOAD
18
20
61
63
SPARE
SPARE
-
-
20
20
1
1
1
1
20
20
-
-
SPARE
SPARE
62
64 akPark
21 SPARE - 20 1 1 20 EXISTING EXISTING LOAD 22
65 SPARE - 20 1 1 20 - SPARE 66
Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

67 SPARE - 20 1 1 20 - SPARE 68
23 SPARE - 20 1 1 20 EXISTING EXISTING LOAD 24
69 SPARE - 20 1 1 20 - SPARE 70 93 Lake Avenue, Danbury, CT 06810
25 SPARE - 20 1 1 20 - SPARE 26 203.778.1017 F 203.778.1018
71 SPARE - 20 1 1 20 - SPARE 72
171 Madison Avenue,
27 SPARE - 20 1 1 20 - SPARE 28
73 SPARE - 20 1 1 20 - SPARE 74 New York, NY 10016
212.695.2422 F 212.695.2423
29 SPARE - 20 1 1 20 - SPARE 30
75 SPACE - - 1 1 - - SPACE 76
www.kohlerronan.com
31 SPARE - 20 1 1 20 - SPARE 32 E-mail [email protected]
77 SPACE - - 1 1 - - SPACE 78
33 SPACE - - 1 1 - - SPACE 34
79 SPACE - - 1 1 - - SPACE 80
35 SPACE - - 1 1 - - SPACE 36
81 SPACE - - 1 1 - - SPACE 82
37 SPACE - - 1 1 - - SPACE 38
83 SPACE - - 1 1 - - SPACE 84 MEDIA CENTER
39 SPACE - - 1 1 - - SPACE 40
SURFACE MTD LOAD PER PHASE 32,970 34,113 30,181 RELOCATION TO
41 SPACE - - 1 1 - - SPACE 42
LOAD PER PHASE 32,422 32,422 32,422
NEMA 1 TOTAL = 97,264 VA
ELIHU BURRITT
SURFACE MTD
NEMA 1 TOTAL = 97,266 VA LIBRARY
208/120V, 3 PHASE, 4 WIRE
LA1 (ETR)
LOAD IN VOLT-AMPERES

POLE

POLE
TRIP

TRIP
LOAD SERVED WIRE & CONDUIT WIRE & CONDUIT LOAD SERVED

43 1248 2424 44
ACCU-1 2 #12+G -3/4"C. 20 2 2 30 2 #10+G -3/4"C. ACCU-2
45 1248 2424 46
47 2424 360 1 20 2 #12+G -3/4"C. EXTERIOR RECEP 48
ACCU-3 2 #10+G -3/4"C. 30 2
49 2424 1 20 - SPARE 50
51 SPARE - 20 1 1 20 - SPARE 52
53 SPARE - 20 1 1 20 - SPARE 54
55 SPARE - 20 1 1 20 - SPARE 56 N
57 SPARE - 20 1 1 20 - SPARE 58
59 SPARE - 20 1 1 20 - SPARE 60
KEY PLAN W E

61 SPARE - 20 1 1 20 - SPARE 62 S
63 SPARE - 20 1 1 20 - SPARE 64
65 SPARE - 20 1 1 20 - SPARE 66
67 SPARE - 20 1 1 20 - SPARE 68
69 SPARE - 20 1 1 20 - SPARE 70
71 SPARE - 20 1 1 20 - SPARE 72
73 SPARE - 20 1 1 20 - SPARE 74
75 SPARE - 20 1 1 20 - SPARE 76
77 SPARE - 20 1 1 20 - SPARE 78
79 SPARE - 20 1 1 20 - SPARE 80
81 SPARE - 20 1 1 20 - SPARE 82
83 SPARE - 20 1 1 20 - SPARE 84
LOAD PER PHASE 6,096 3,672 2,784
SURFACE MTD
NEMA 1 TOTAL = 12,552 VA

22 E-501
 CONDUIT BUSHING BLDG. STRUCTURE
REVISIONS
6" MIN. NUMBER DATE DESCRIPTION

ACCESSIBLE CLG.
DRAG WIRE

1"C. EMT (CAT 6)

1-1/4"C. EMT (CAT 6A)

akPark
FACEPLATES FOR ALL OUTLETS
FURNISHED BY OTHERS. E.C. SHALL
Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

PROVIDE BLANK PLATES ONLY 2-1/2" DEEP
4"X4" SQUARE BOX 93 Lake Avenue, Danbury, CT 06810
203.778.1017 F 203.778.1018
18"
171 Madison Avenue,
New York, NY 10016
212.695.2422 F 212.695.2423
FIN. FLOOR
www.kohlerronan.com
NOTES: E-mail [email protected]

1. REFER TO T-SERIES DRAWINGS FOR ALL BOX LOCATIONS.

1 VOICE / DATA / AV OUTLET INSTALLATION DETAIL 2 LADDER RACK RECEPTACLE MOUNTING MEDIA CENTER
E-601 SCALE: NONE E-601 SCALE: NONE RELOCATION TO
ELIHU BURRITT
LIBRARY

GENERAL NOTES:

PROVIDE UL LISTED FIRE/SMOKE PENETRATION ASSEMBLY IN ACCORDANCE W/ UL1479,

ASTM E814 REQUIREMENTS FOR WALL TYPE, RATING, PIPE SIZE INSTALLED.

FIRE STOPPING SHALL HAVE A RATING EQUAL TO OR GREATER THAN THE WALL BEING
PENETRATED - SEE SPECIFICATIONS. REFER TO ARCHITECTURAL DRAWINGS FOR WALL
RATINGS AND LOCATIONS.

FIRE OR SMOKE RATED

N
DRYWALL PARTITION SCHEDULE 40 GALVANIZED
PIPE SLEEVE
KEY PLAN W E
SCHEDULE 40 GALVANIZED
PIPE SLEEVE FIRE STOP SEALANT S

CONDUIT CONDUIT

UL LISTED FIRE SEALANT UL LISTED FIRE SEALANT

REFER TO SPECIFICATIONS REFER TO SPECIFICATIONS
GROUT SLEEVE IN
MASONRY WALL
FIRE OR SMOKE RATED
CONCRETE/MASONRY WALL

3 WALL PENETRATION W/ FIRE/SMOKE SEAL DETAIL 4 TYPICAL DEVICE MOUNTING HEIGHT DETAIL DETAILS -
E-601 SCALE: NONE E-601 SCALE: NONE
ELECTRICAL

22 E-601
 NOTES
400A 1. ELECTRICAL CONTRACTOR SHALL VERIFY QUANTITIES OF ALL DEVICES. ADDITIONAL DEVICES MAY BE
PROVIDE LOCKABLE DISCONNECT
250A
TRANSFORMER NOTES NECESSARY. REFER TO REFLECTED CEILING PLANS FOR ADDITIONAL DEVICES.

2. A MAXIMUM OF 10 SENSORS SHALL BE ENERGIZED PER POWER PACK. SUPPLEMENT WITH

3#250KCMIL + #4G IN 2-1/2"C ADDITIONAL POWER PACKS IF OVER 10 SENSORS.
150kVA TRANSFORMER 480V PRIMARY 208Y/120V.
MARK ON TRANSFORMER A 3. AUXILIARY RELAY REQUIRES SENSOR POWER TO FUNCTION. AUXILIARY RELAY CHANGES STATE
DISCONNECT LOCATIONS WHEN ALL CONNECTED SENSORS REGISTER UNOCCUPIED. GREY AND BROWN WIRES ARE
#1/0G IN 1"C TO BUILDING STEEL TX-1 CONNECTED DURING OCCUPIED STATE. VIOLET AND BROWN WIRES ARE CONNECTED DURING
UNOCCUPIED STATE.
CLASS II 4. LOW VOLTAGE SWITCH MAY BE PROGRAMMED FOR EITHER VACANCY OR OCCUPANCY MODE. REFER
AUXILIARY RELAY WIRING SENSOR
(2 SETS OF) 4#250KCMIL + #2G IN (2) 3"C TO BUILDING BLACK (COMMON) TO REFLECTED CEILING PLANS FOR CONTROL TYPE.
VIOLET
MANAGEMENT BROWN WHITE
SYSTEM GREY RED 12-24V POWER

PPS4 POWER PACK

OR ADDITIONAL SENSORS N H
INDICATED ON FLOOR PLANS BLACK (COMMON)
WHITE BLACK
WHITE
RED 12-24V POWER RED
WHITE
(OCCUPANT OUTPUT) BLK-120V
WHITE ORG-277V
WHITE W/ BLUE STRIPE BLK/ORG

RED 12-24V POWER BLUE

PP-2FN
S BLUE LIGHTING
BLACK (COMMON)
REVISIONS
LOW VOLTAGE NUMBER DATE DESCRIPTION
SWITCH

akPark
Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

93 Lake Avenue, Danbury, CT 06810

203.778.1017 F 203.778.1018
NOTES 171 Madison Avenue,
New York, NY 10016
212.695.2422 F 212.695.2423
1. ELECTRICAL CONTRACTOR SHALL VERIFY QUANTITIES OF ALL DEVICES. ADDITIONAL DEVICES MAY BE www.kohlerronan.com
NECESSARY. REFER TO REFLECTED CEILING PLANS FOR ADDITIONAL DEVICES. E-mail [email protected]

2. A MAXIMUM OF 10 SENSORS SHALL BE ENERGIZED PER POWER PACK. SUPPLEMENT WITH

ADDITIONAL POWER PACKS IF OVER 10 SENSORS.

3. AUXILIARY RELAY REQUIRES SENSOR POWER TO FUNCTION. AUXILIARY RELAY CHANGES STATE MEDIA CENTER
LIGHTING CIRCUITS WHEN ALL CONNECTED SENSORS REGISTER UNOCCUPIED. GREY AND BROWN WIRES ARE
CONNECTED DURING OCCUPIED STATE. VIOLET AND BROWN WIRES ARE CONNECTED DURING RELOCATION TO
UNOCCUPIED STATE.
ELIHU BURRITT
CLASS II 4. LOW VOLTAGE DIMMER MAY BE PROGRAMMED FOR EITHER VACANCY OR OCCUPANCY MODE. REFER
AUXILIARY RELAY WIRING SENSOR
BRANCH CIRCUIT
TO BUILDING BLACK (COMMON) TO REFLECTED CEILING PLANS FOR CONTROL TYPE. LIBRARY
MAINTENANCE SWITCH VIOLET
MANAGEMENT BROWN WHITE
SYSTEM GREY RED 12-24V POWER
S
LIGHTING ZONE POWER PACK
BMS LIGHTING OR ADDITIONAL SENSORS N H
POWER PACK JUNCTION BOX
(SEE NOTE 1) PANEL BOARD INDICATED ON FLOOR PLANS BLACK (COMMON)
(SEE NOTE 2) BLACK
WHITE
WHITE
RED 12-24V POWER RED
WHITE
(OCCUPANT OUTPUT) BLK-120V
WHITE ORG-277V
WHITE W/ BLUE STRIPE BLK/ORG

NOTES: RED 12-24V POWER GREY FROM FIXTURE TO BLACK OF BLUE

S LOW VOLTAGE SIDE OF POWER PACK BLUE LIGHTING
BLACK (COMMON)
1. EACH CORRIDOR LIGHTING ZONE SHALL HAVE AN ASSOCIATED BMS RELAY MODULE 0-10V DIMMING LEAD
FOR SCHEDULED CONTROL OF BUILDING LIGHTING VIA THE BMS SYSTEM, COORDINATE
WITH DIVISION 23 FOR INTERFACE REQUIREMENTS.
LOW VOLTAGE
DIMMER
2. CORRIDOR LIGHTING ZONE FIXTURES ARE CONTROLLED AFTER HOURS VIA N
OCCUPANCY SENSORS. ADDITIONAL POWER PACKS MAY BE NECESSARY.
KEY PLAN W E
3 TYPICAL CORRIDOR LIGHTING CONTROL DIAGRAM 4 TYPICAL DIMMED LIGHTING CONTROL WIRING DIAGRAM S
E-602 SCALE: NONE E-602 SCALE: NONE

DETAILS -
ELECTRICAL

22 E-602
 REVISIONS
NUMBER DATE DESCRIPTION

akPark
Architects LLC

312 Park Rd, W. Hartford, CT (860)232-6664

93 Lake Avenue, Danbury, CT 06810

203.778.1017 F 203.778.1018

171 Madison Avenue,

New York, NY 10016
212.695.2422 F 212.695.2423

www.kohlerronan.com
E-mail [email protected]

MEDIA CENTER
RELOCATION TO
ELIHU BURRITT
LIBRARY

KEY PLAN W E

S
S S

S S
S
S

22 E-701