Scribd
Upload
86 views11 pages

Truss - 3

This document provides a structural calculation and analysis output for the design of a steel truss located in Romblon. It analyzes 20 beams under different load combinations, reporting the maximum compressive and tensile stresses, and their locations, for each beam and load case. The analysis evaluates dead loads, live loads, and wind loads to ensure the truss design is structurally sound.

Uploaded by

Jake Cortez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
86 views11 pages

Truss - 3

This document provides a structural calculation and analysis output for the design of a steel truss located in Romblon. It analyzes 20 beams under different load combinations, reporting the maximum compressive and tensile stresses, and their locations, for each beam and load case. The analysis evaluates dead loads, live loads, and wind loads to ensure the truss design is structurally sound.

Uploaded by

Jake Cortez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

STRUCTURAL CALCULATION

Poject: Design of Steel Trusss


Location: Romblon

Analysis Output

Max Compressive Max Tensile


Beam
Load Combination Length m Stress Stress
No. Dist m Corner Dist m Corner
N/mm2 N/mm2
1 1 DL 1 -39.969 0.833 3
2 LL 1 4.269 1 1 -108.896 1 3
3 WL1 1 42.894 1 3 -2.613 1 1
4 WL2 1 206.04 1 3 -4.323 1 1
5 1.2DL + 0.5LL + 1.0WL1 1 -59.469 0.833 3
6 1.2DL + 0.5LL + 1.0WL2 1 104.267 1 3 -3.398 1 1
7 0.9DL + 1.0WL1 1 7.401 1 3 -4.638 0.417 3
8 0.9DL + 1.0WL2 1 170.546 1 3 -5.23 1 1
9 1.0DL + 1.0LL 1 3.261 1 1 -148.333 1 3
7 1 DL 1 15.429 1 3
2 LL 1 22.711 1 3
3 WL1 1 -7.061 1 3
4 WL2 1 -46.831 1 3
5 1.2DL + 0.5LL + 1.0WL1 1 25.47 0 1
6 1.2DL + 0.5LL + 1.0WL2 1 -28.214 0.5 3
7 0.9DL + 1.0WL1 1 10.619 0 3 -1.068 0 1
8 0.9DL + 1.0WL2 1 -40.973 0.5 3
9 1.0DL + 1.0LL 1 38.141 1 3
8 1 DL 1 20.706 0 1
2 LL 1 35.13 0 1
3 WL1 1 -28.183 1 1
4 WL2 1 -58.834 1 3
5 1.2DL + 0.5LL + 1.0WL1 1 18.812 1 3
6 1.2DL + 0.5LL + 1.0WL2 1 -26.92 0.5 3
7 0.9DL + 1.0WL1 1 -17.843 1 1
8 0.9DL + 1.0WL2 1 -47.771 0.5 3
9 1.0DL + 1.0LL 1 55.837 0 1
9 1 DL 1 29.362 1 3
2 LL 1 54.615 1 3
3 WL1 1 -76.605 1 3
4 WL2 1 -66.896 0 1
5 1.2DL + 0.5LL + 1.0WL1 1 7.465 0 3 -16.655 0.75 3
6 1.2DL + 0.5LL + 1.0WL2 1 -23.783 1 1
7 0.9DL + 1.0WL1 1 -50.398 0.917 3
8 0.9DL + 1.0WL2 1 -49.592 1 1
9 1.0DL + 1.0LL 1 83.977 1 3
10 1 DL 1.033 15.595 0 1
2 LL 1.033 21.15 0 1
3 WL1 1.033 -73.838 0 1
4 WL2 1.033 3.914 1.033 1 -2.239 1.033 3
5 1.2DL + 0.5LL + 1.0WL1 1.033 -47.588 0.258 3
6 1.2DL + 0.5LL + 1.0WL2 1.033 31.168 0 1
7 0.9DL + 1.0WL1 1.033 -60.034 0.086 3
8 0.9DL + 1.0WL2 1.033 15.914 0 1
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon

9 1.0DL + 1.0LL 1.033 36.746 0 1


11 1 DL 1.033 9.421 1.033 3 -1.013 0.517 3
2 LL 1.033 6.029 0 1
3 WL1 1.033 -21.717 0 1
4 WL2 1.033 19.336 1.033 3 -5.563 1.033 1
5 1.2DL + 0.5LL + 1.0WL1 1.033 -19.167 1.033 1
6 1.2DL + 0.5LL + 1.0WL2 1.033 32.663 1.033 3 -3.953 1.033 1
7 0.9DL + 1.0WL1 1.033 -21.797 0 1
8 0.9DL + 1.0WL2 1.033 27.816 1.033 3 -6.459 1.033 1
9 1.0DL + 1.0LL 1.033 13.464 1.033 3
12 1 DL 1.033 7.596 0 3 -4.131 0.603 3
2 LL 1.033 4.245 1.033 3 -0.549 1.033 1
3 WL1 1.033 2.04 1.033 1 -15.685 1.033 3
4 WL2 1.033 33.18 1.033 1 -62.742 1.033 3
5 1.2DL + 0.5LL + 1.0WL1 1.033 9.651 0 3 -13.34 0.775 3
6 1.2DL + 0.5LL + 1.0WL2 1.033 31.901 1.033 1 -56.708 1.033 3
7 0.9DL + 1.0WL1 1.033 7.415 0 3 -14.12 0.861 3
8 0.9DL + 1.0WL2 1.033 32.426 1.033 1 -59.809 1.033 3
9 1.0DL + 1.0LL 1.033 7.51 0 3 -1.953 0.517 3
13 1 DL 1.127 5.628 0 3 -4.857 1.127 3
2 LL 1.127 9.901 1.127 1 -18.034 1.127 3
3 WL1 1.127 66.436 1.127 3 -36.472 1.127 1
4 WL2 1.127 115.946 0.563 3 -120.359 0 3
5 1.2DL + 0.5LL + 1.0WL1 1.127 51.591 1.127 3 -28.535 1.127 1
6 1.2DL + 0.5LL + 1.0WL2 1.127 113.899 0.563 3 -134.704 1.127 3
7 0.9DL + 1.0WL1 1.127 62.065 1.127 3 -34.232 1.127 1
8 0.9DL + 1.0WL2 1.127 116.293 0.563 3 -124.23 1.127 3
9 1.0DL + 1.0LL 1.127 13.622 0 3 -22.89 1.127 3
14 1 DL 1.004 44.885 0.837 1
2 LL 1.004 108.759 0.67 1
3 WL1 1.004 -56.831 1.004 1
4 WL2 1.004 0.168 0.67 3 -188.609 0.67 1
5 1.2DL + 0.5LL + 1.0WL1 1.004 55.686 0.586 1 -6.776 0.586 3
6 1.2DL + 0.5LL + 1.0WL2 1.004 16.358 0.586 3 -81.997 0.586 1
7 0.9DL + 1.0WL1 1.004 -17.312 0.335 3
8 0.9DL + 1.0WL2 1.004 7.221 0.586 3 -149.13 0.586 1
9 1.0DL + 1.0LL 1.004 153.018 0.67 1
15 1 DL 0.838 7.044 0 1
2 LL 0.838 18.096 0.838 3
3 WL1 0.838 -66.995 0.838 3
4 WL2 0.838 -0.762 0 1
5 1.2DL + 0.5LL + 1.0WL1 0.838 -49.559 0.838 3
6 1.2DL + 0.5LL + 1.0WL2 0.838 16.772 0 1
7 0.9DL + 1.0WL1 0.838 -60.704 0.838 3
8 0.9DL + 1.0WL2 0.838 5.628 0 1
9 1.0DL + 1.0LL 0.838 25.106 0 1
18 1 DL 0.279 -2.791 0.279 3
2 LL 0.279 -4.457 0.279 3
3 WL1 0.279 0.272 0 3 -0.051 0 1
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon

4 WL2 0.279 10.057 0.279 3


5 1.2DL + 0.5LL + 1.0WL1 0.279 -5.527 0 1
6 1.2DL + 0.5LL + 1.0WL2 0.279 4.566 0 1
7 0.9DL + 1.0WL1 0.279 -2.515 0 1
8 0.9DL + 1.0WL2 0.279 7.578 0 1
9 1.0DL + 1.0LL 0.279 -7.248 0.279 3
19 1 DL 0.373 -3.737 0.373 3
2 LL 0.373 -6.664 0.373 3
3 WL1 0.373 -1.561 0.373 3
4 WL2 0.373 16.47 0.373 3
5 1.2DL + 0.5LL + 1.0WL1 0.373 -9.378 0.373 3
6 1.2DL + 0.5LL + 1.0WL2 0.373 8.653 0.373 3
7 0.9DL + 1.0WL1 0.373 -4.925 0.373 3
8 0.9DL + 1.0WL2 0.373 13.106 0.373 3
9 1.0DL + 1.0LL 0.373 -10.402 0.373 3
20 1 DL 0.466 -4.693 0.466 3
2 LL 0.466 -8.882 0.466 3
3 WL1 0.466 4.604 0.466 3
4 WL2 0.466 16.45 0 1
5 1.2DL + 0.5LL + 1.0WL1 0.466 -5.8 0.466 1
6 1.2DL + 0.5LL + 1.0WL2 0.466 6.465 0 1
7 0.9DL + 1.0WL1 0.466 0.38 0.466 3 -0.018 0.466 1
8 0.9DL + 1.0WL2 0.466 12.276 0 1
9 1.0DL + 1.0LL 0.466 -13.575 0.466 3
21 1 DL 0.559 -5.643 0.559 3
2 LL 0.559 -11.076 0.559 3
3 WL1 0.559 14.243 0.559 3
4 WL2 0.559 13.219 0.559 3
5 1.2DL + 0.5LL + 1.0WL1 0.559 1.992 0 1
6 1.2DL + 0.5LL + 1.0WL2 0.559 1.016 0 1
7 0.9DL + 1.0WL1 0.559 9.187 0 1
8 0.9DL + 1.0WL2 0.559 8.143 0 1
9 1.0DL + 1.0LL 0.559 -16.719 0.559 3
22 1 DL 0.652 -6.621 0.652 3
2 LL 0.652 -13.311 0.652 3
3 WL1 0.652 22.612 0.652 3
4 WL2 0.652 11.42 0 1
5 1.2DL + 0.5LL + 1.0WL1 0.652 8.011 0.652 3
6 1.2DL + 0.5LL + 1.0WL2 0.652 -3.185 0.652 3
7 0.9DL + 1.0WL1 0.652 16.653 0.652 3
8 0.9DL + 1.0WL2 0.652 5.547 0 1
9 1.0DL + 1.0LL 0.652 -19.932 0.652 3
23 1 DL 0.745 -7.525 0.745 3
2 LL 0.745 -15.386 0.745 3
3 WL1 0.745 29.536 0 1
4 WL2 0.745 10.022 0 1
5 1.2DL + 0.5LL + 1.0WL1 0.745 12.9 0 1
6 1.2DL + 0.5LL + 1.0WL2 0.745 -6.731 0.745 3
7 0.9DL + 1.0WL1 0.745 22.822 0 1
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon

8 0.9DL + 1.0WL2 0.745 3.365 0 1


9 1.0DL + 1.0LL 0.745 -22.91 0.745 3
25 1 DL 1.031 2.152 0 1
2 LL 1.031 7.2 1.031 3
3 WL1 1.031 -26.53 1.031 3
4 WL2 1.031 -2.026 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.031 -20.435 1.031 3
6 1.2DL + 0.5LL + 1.0WL2 1.031 4.416 0 1
7 0.9DL + 1.0WL1 1.031 -24.659 1.031 3
8 0.9DL + 1.0WL2 1.031 0.2 0 1 -0.114 0 3
9 1.0DL + 1.0LL 1.031 9.292 0 1
26 1 DL 1.038 7.154 0 3 -4.578 0.605 3
2 LL 1.038 36.95 0 3 -24.473 0.605 3
3 WL1 1.038 90.122 0.605 3 -136.194 0 3
4 WL2 1.038 68.318 1.038 3 -27.547 1.038 1
5 1.2DL + 0.5LL + 1.0WL1 1.038 72.392 0.605 3 -109.135 0 3
6 1.2DL + 0.5LL + 1.0WL2 1.038 77.183 1.038 3 -31.665 1.038 1
7 0.9DL + 1.0WL1 1.038 86.002 0.605 3 -129.756 0 3
8 0.9DL + 1.0WL2 1.038 70.9 1.038 3 -28.733 1.038 1
9 1.0DL + 1.0LL 1.038 44.104 0 3 -29.052 0.605 3
27 1 DL 1.038 6.608 1.038 3 -3.798 1.038 1
2 LL 1.038 35.581 1.038 3 -18.188 1.038 1
3 WL1 1.038 67.038 1.038 1 -131.149 1.038 3
4 WL2 1.038 11.228 1.038 1 -13.813 1.038 3
5 1.2DL + 0.5LL + 1.0WL1 1.038 53.387 1.038 1 -105.429 1.038 3
6 1.2DL + 0.5LL + 1.0WL2 1.038 27.754 0 3 -15.674 0.605 3
7 0.9DL + 1.0WL1 1.038 63.62 1.038 1 -125.201 1.038 3
8 0.9DL + 1.0WL2 1.038 12.27 0 3 -9.256 0.865 3
9 1.0DL + 1.0LL 1.038 42.189 1.038 3 -21.986 1.038 1
28 1 DL 1.038 6.513 0 3 -6.411 0 1
2 LL 1.038 32.028 0 3 -22.281 0 1
3 WL1 1.038 82.607 0 1 -119.137 0 3
4 WL2 1.038 8.08 1.038 3
5 1.2DL + 0.5LL + 1.0WL1 1.038 63.774 0 1 -95.308 0 3
6 1.2DL + 0.5LL + 1.0WL2 1.038 25.614 0 3 -14.404 0 1
7 0.9DL + 1.0WL1 1.038 76.838 0 1 -113.275 0 3
8 0.9DL + 1.0WL2 1.038 10.831 1.038 3 -2.883 1.038 1
9 1.0DL + 1.0LL 1.038 38.54 0 3 -28.692 0 1
29 1 DL 1.004 11.053 1.004 3
2 LL 1.004 42.308 1.004 3 -2.683 0.502 3
3 WL1 1.004 40.088 0.502 3 -81.205 1.004 3
4 WL2 1.004 -14.549 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.004 41.068 0.502 3 -46.937 0 3
6 1.2DL + 0.5LL + 1.0WL2 1.004 22.053 1.004 3 -12.478 0.502 3
7 0.9DL + 1.0WL1 1.004 41.829 0.502 3 -71.256 1.004 3
8 0.9DL + 1.0WL2 1.004 -11.717 0.502 3
9 1.0DL + 1.0LL 1.004 53.362 1.004 3 -0.749 0.502 3
38 1 DL 1.004 2.986 1.004 3 -9.957 1.004 1
2 LL 1.004 23.931 1.004 3 -30.361 1.004 1
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon

3 WL1 1.004 112.421 1.004 1 -89.279 1.004 3


4 WL2 1.004 5.786 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.004 85.292 1.004 1 -73.731 1.004 3
6 1.2DL + 0.5LL + 1.0WL2 1.004 17.737 1.004 3 -22.305 1.004 1
7 0.9DL + 1.0WL1 1.004 103.46 1.004 1 -86.592 1.004 3
8 0.9DL + 1.0WL2 1.004 4.876 1.004 3 -5.08 0.418 3
9 1.0DL + 1.0LL 1.004 26.916 1.004 3 -40.318 1.004 1
39 1 DL 1.004 6.452 1.004 3 -3.783 1.004 1
2 LL 1.004 31.28 1.004 3 -15.562 1.004 1
3 WL1 1.004 65.691 1.004 1 -75.178 1.004 3
4 WL2 1.004 -6.249 1.004 3
5 1.2DL + 0.5LL + 1.0WL1 1.004 53.371 1.004 1 -51.796 1.004 3
6 1.2DL + 0.5LL + 1.0WL2 1.004 17.57 0 3 -15.573 0.502 3
7 0.9DL + 1.0WL1 1.004 62.287 1.004 1 -69.371 1.004 3
8 0.9DL + 1.0WL2 1.004 0.892 0 3 -7.78 0.502 3
9 1.0DL + 1.0LL 1.004 37.732 1.004 3 -19.345 1.004 1
42 1 DL 0.186 -1.757 0.186 3
2 LL 0.186 -2.041 0.186 3
3 WL1 0.186 -0.756 0.186 3
4 WL2 0.186 5.481 0.186 3
5 1.2DL + 0.5LL + 1.0WL1 0.186 -3.885 0.186 3
6 1.2DL + 0.5LL + 1.0WL2 0.186 2.352 0.186 3 -0.009 0 3
7 0.9DL + 1.0WL1 0.186 -2.338 0.186 3
8 0.9DL + 1.0WL2 0.186 3.899 0.186 3
9 1.0DL + 1.0LL 0.186 -3.798 0.186 3
44 1 DL 0.093 0.85 0.093 3 -1.346 0 3
2 LL 0.093 4.129 0.093 3 -1.1 0 3
3 WL1 0.093 1.412 0 3 -2.577 0.093 3
4 WL2 0.093 0.847 0 3 -6.545 0.093 3
5 1.2DL + 0.5LL + 1.0WL1 0.093 0.508 0.093 3 -0.753 0 3
6 1.2DL + 0.5LL + 1.0WL2 0.093 -3.46 0.093 3
7 0.9DL + 1.0WL1 0.093 0.2 0 3 -1.811 0.093 3
8 0.9DL + 1.0WL2 0.093 -5.78 0.093 3
9 1.0DL + 1.0LL 0.093 4.979 0.093 3 -2.446 0 3
45 1 DL 0.935 4.492 0 1
2 LL 0.935 12.223 0.935 3
3 WL1 0.935 -44.996 0.935 3
4 WL2 0.935 -0.328 0 1
5 1.2DL + 0.5LL + 1.0WL1 0.935 -33.569 0.935 3
6 1.2DL + 0.5LL + 1.0WL2 0.935 11.172 0 1
7 0.9DL + 1.0WL1 0.935 -41.01 0.935 3
8 0.9DL + 1.0WL2 0.935 3.756 0 1
9 1.0DL + 1.0LL 0.935 16.709 0 1
46 1 DL 1.46 -3.48 0.73 3
2 LL 1.46 -2.889 0 1
3 WL1 1.46 10.647 0 1
4 WL2 1.46 0.914 1.46 1
5 1.2DL + 0.5LL + 1.0WL1 1.46 8.432 0.73 1
6 1.2DL + 0.5LL + 1.0WL2 1.46 -4.995 0.73 3
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon

7 0.9DL + 1.0WL1 1.46 9.989 0.73 1


8 0.9DL + 1.0WL2 1.46 0.373 0.851 1 -2.527 0.73 3
9 1.0DL + 1.0LL 1.46 -6.327 0.73 3
47 1 DL 1.393 -6.775 0.697 3
2 LL 1.393 -10.598 0 1
3 WL1 1.393 39.028 0 1
4 WL2 1.393 0.976 1.393 3
5 1.2DL + 0.5LL + 1.0WL1 1.393 28.934 0.697 1
6 1.2DL + 0.5LL + 1.0WL2 1.393 -12.525 0.697 3
7 0.9DL + 1.0WL1 1.393 35.399 0.697 1
8 0.9DL + 1.0WL2 1.393 -5.199 0.697 3
9 1.0DL + 1.0LL 1.393 -17.362 0.697 3
48 1 DL 1.331 -10.431 0.665 3
2 LL 1.331 -19.135 1.331 1
3 WL1 1.331 70.557 1.331 1
4 WL2 1.331 0.977 1.331 1
5 1.2DL + 0.5LL + 1.0WL1 1.331 51.699 0.665 1
6 1.2DL + 0.5LL + 1.0WL2 1.331 -21.115 0.665 3
7 0.9DL + 1.0WL1 1.331 63.583 0.665 1
8 0.9DL + 1.0WL2 1.331 -8.44 0.665 3
9 1.0DL + 1.0LL 1.331 -29.523 0.665 3
49 1 DL 1.247 13.208 0.624 1
2 LL 1.247 29.352 0 1
3 WL1 1.247 -64.401 1.247 3
4 WL2 1.247 -15.023 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.247 -36.723 0.624 3
6 1.2DL + 0.5LL + 1.0WL2 1.247 15.534 0.624 1
7 0.9DL + 1.0WL1 1.247 -54.626 0.624 3
8 0.9DL + 1.0WL2 1.247 -5.289 0.624 3
9 1.0DL + 1.0LL 1.247 42.467 0.624 1
50 1 DL 1.194 12.706 0.597 1
2 LL 1.194 28.319 0 1
3 WL1 1.194 -54.765 0 1
4 WL2 1.194 -18.275 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.194 -28.096 0.597 3
6 1.2DL + 0.5LL + 1.0WL2 1.194 11.185 0.597 1
7 0.9DL + 1.0WL1 1.194 -45.345 0.597 3
8 0.9DL + 1.0WL2 1.194 -8.931 0.597 3
9 1.0DL + 1.0LL 1.194 40.959 0.597 1
51 1 DL 1.146 12.136 0.573 1
2 LL 1.146 27.119 0 1
3 WL1 1.146 -45.622 1.146 1
4 WL2 1.146 -23.507 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.146 -20.185 0.573 3
6 1.2DL + 0.5LL + 1.0WL2 1.146 4.706 0.573 1
7 0.9DL + 1.0WL1 1.146 -36.697 0.573 3
8 0.9DL + 1.0WL2 1.146 -14.579 0.573 3
9 1.0DL + 1.0LL 1.146 39.22 0.573 1
61 1 DL 1 -39.431 0.167 3
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon

2 LL 1 3.396 0 1 -107.647 0 3
3 WL1 1 41.937 0 3 -1.945 0 1
4 WL2 1 204.279 0 3 -3.091 0 1
5 1.2DL + 0.5LL + 1.0WL1 1 -58.58 0 1
6 1.2DL + 0.5LL + 1.0WL2 1 103.761 0 3 -3.044 0 1
7 0.9DL + 1.0WL1 1 10.804 1 3 -4.994 1 1
8 0.9DL + 1.0WL2 1 169.259 0 3 -4.329 0 1
9 1.0DL + 1.0LL 1 2.02 0 1 -146.559 0 3
62 1 DL 1 -19.646 0.5 3
2 LL 1 -40.704 0 1
3 WL1 1 25.679 0 1
4 WL2 1 68.494 0 1
5 1.2DL + 0.5LL + 1.0WL1 1 -19.383 0.5 3
6 1.2DL + 0.5LL + 1.0WL2 1 35.363 1 3
7 0.9DL + 1.0WL1 1 15.542 0 1
8 0.9DL + 1.0WL2 1 58.357 0 1
9 1.0DL + 1.0LL 1 -59.295 0.417 3
63 1 DL 1 -12.83 0.5 3
2 LL 1 -26.325 0 1
3 WL1 1 23.619 1 3
4 WL2 1 39.217 0 1
5 1.2DL + 0.5LL + 1.0WL1 1 10.176 1 3 -5.009 1 1
6 1.2DL + 0.5LL + 1.0WL2 1 19.798 0 1
7 0.9DL + 1.0WL1 1 21.166 1 3
8 0.9DL + 1.0WL2 1 34.524 0 1
9 1.0DL + 1.0LL 1 -36.624 0.417 3
64 1 DL 1 3.419 1 3 -5.961 0.5 3
2 LL 1 -8.175 0 1
3 WL1 1 24.617 0 1
4 WL2 1 -7.66 0 1
5 1.2DL + 0.5LL + 1.0WL1 1 24.07 1 3
6 1.2DL + 0.5LL + 1.0WL2 1 -16.019 0.5 3
7 0.9DL + 1.0WL1 1 26.758 0 1
8 0.9DL + 1.0WL2 1 -10.789 0.583 3
9 1.0DL + 1.0LL 1 -12.946 0.417 3
65 1 DL 1 9.395 1 3
2 LL 1 10.118 0 1
3 WL1 1 16.838 0 1
4 WL2 1 -31.367 1 3
5 1.2DL + 0.5LL + 1.0WL1 1 30.534 0 1
6 1.2DL + 0.5LL + 1.0WL2 1 -26.912 0.5 3
7 0.9DL + 1.0WL1 1 24.608 0 1
8 0.9DL + 1.0WL2 1 -30.756 0.5 3
9 1.0DL + 1.0LL 1 17.914 1 3
66 1 DL 1.004 43.093 0.167 1
2 LL 1.004 104.097 0.335 1
3 WL1 1.004 -59.971 0 1
4 WL2 1.004 4.896 0.335 3 -173.425 0.335 1
5 1.2DL + 0.5LL + 1.0WL1 1.004 46.576 0.335 1 -10.038 0.335 3
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon

6 1.2DL + 0.5LL + 1.0WL2 1.004 18.856 0.418 3 -80.702 1.004 3


7 0.9DL + 1.0WL1 1.004 -21.705 1.004 1
8 0.9DL + 1.0WL2 1.004 10.796 0.335 3 -136.056 1.004 3
9 1.0DL + 1.0LL 1.004 146.558 0.251 1
67 1 DL 1.004 29.5 0.502 1
2 LL 1.004 80.929 1.004 3
3 WL1 1.004 -53.894 1.004 1
4 WL2 1.004 -147.581 1.004 3
5 1.2DL + 0.5LL + 1.0WL1 1.004 44.549 1.004 3
6 1.2DL + 0.5LL + 1.0WL2 1.004 -74.26 1.004 3
7 0.9DL + 1.0WL1 1.004 -31.285 1.004 1
8 0.9DL + 1.0WL2 1.004 -122.939 1.004 3
9 1.0DL + 1.0LL 1.004 108.309 1.004 3
68 1 DL 1.004 24.646 1.004 3
2 LL 1.004 74.421 1.004 3
3 WL1 1.004 -78.822 1.004 3
4 WL2 1.004 -119.293 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.004 31.457 0 3 -26.803 0.67 3
6 1.2DL + 0.5LL + 1.0WL2 1.004 27.928 0.586 3 -58.189 0 3
7 0.9DL + 1.0WL1 1.004 -56.64 1.004 3
8 0.9DL + 1.0WL2 1.004 9.029 0.502 3 -99.27 0 1
9 1.0DL + 1.0LL 1.004 99.067 1.004 3
69 1 DL 1.004 20.372 1.004 3
2 LL 1.004 64.262 1.004 3
3 WL1 1.004 22.335 0.418 3 -124.979 1.004 3
4 WL2 1.004 -66.794 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.004 45.595 0.418 3 -68.402 1.004 3
6 1.2DL + 0.5LL + 1.0WL2 1.004 28.01 1.004 3 -28.235 0.335 3
7 0.9DL + 1.0WL1 1.004 32.378 0.418 3 -106.644 1.004 3
8 0.9DL + 1.0WL2 1.004 -49.331 0 1
9 1.0DL + 1.0LL 1.004 84.634 1.004 3
70 1 DL 1.004 15.906 1.004 3
2 LL 1.004 53.685 1.004 3
3 WL1 1.004 15.754 0.502 3 -109.322 0 3
4 WL2 1.004 -25.444 1.004 3
5 1.2DL + 0.5LL + 1.0WL1 1.004 29.664 0 1 -65.241 0 3
6 1.2DL + 0.5LL + 1.0WL2 1.004 30.438 0 3 -9.432 0 1
7 0.9DL + 1.0WL1 1.004 21.701 0.502 3 -95.733 0 3
8 0.9DL + 1.0WL2 1.004 -17.716 0 1
9 1.0DL + 1.0LL 1.004 69.591 1.004 3
71 1 DL 1.103 11.644 0.552 1
2 LL 1.103 26.088 1.103 1
3 WL1 1.103 -33.553 0 1
4 WL2 1.103 -31.166 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.103 -9.116 0.552 3
6 1.2DL + 0.5LL + 1.0WL2 1.103 -6.759 0.552 3
7 0.9DL + 1.0WL1 1.103 -24.981 0.552 3
8 0.9DL + 1.0WL2 1.103 -22.624 0.552 3
9 1.0DL + 1.0LL 1.103 37.727 0.552 1
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon

72 1 DL 1.067 11.217 0.534 1


2 LL 1.067 25.226 1.067 1
3 WL1 1.067 -12.57 0 1
4 WL2 1.067 -47.262 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.067 13.599 0.534 1
6 1.2DL + 0.5LL + 1.0WL2 1.067 -23.589 0.534 3
7 0.9DL + 1.0WL1 1.067 -3.83 0.623 3
8 0.9DL + 1.0WL2 1.067 -38.886 0.534 3
9 1.0DL + 1.0LL 1.067 36.442 0.534 1
73 1 DL 1.038 10.746 0.519 1
2 LL 1.038 24.267 0 1
3 WL1 1.038 2.034 1.038 3
4 WL2 1.038 -56.668 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.038 26.92 0.519 1
6 1.2DL + 0.5LL + 1.0WL2 1.038 -33.954 0.519 3
7 0.9DL + 1.0WL1 1.038 11.567 0.519 1
8 0.9DL + 1.0WL2 1.038 -48.578 0.519 3
9 1.0DL + 1.0LL 1.038 35.004 0.519 1
74 1 DL 1.017 10.551 0.509 1
2 LL 1.017 24.026 0 1
3 WL1 1.017 0.299 0 1
4 WL2 1.017 -54.618 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.017 24.698 0.509 1
6 1.2DL + 0.5LL + 1.0WL2 1.017 -32.245 0.509 3
7 0.9DL + 1.0WL1 1.017 9.524 0.509 1
8 0.9DL + 1.0WL2 1.017 -46.641 0.509 3
9 1.0DL + 1.0LL 1.017 34.568 0.509 1
75 1 DL 1.004 3.507 0.502 1
2 LL 1.004 7.606 0 1
3 WL1 1.004 7.351 0 1
4 WL2 1.004 -23.893 0 1
5 1.2DL + 0.5LL + 1.0WL1 1.004 14.699 0.502 1
6 1.2DL + 0.5LL + 1.0WL2 1.004 -17.186 0.502 3
7 0.9DL + 1.0WL1 1.004 9.902 0.502 1
8 0.9DL + 1.0WL2 1.004 -21.212 0 1
9 1.0DL + 1.0LL 1.004 11.007 0.418 1
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon
Design Output
Design Actual Allowabl
Beam L/C Ax cm2 Iz cm4 Iy cm4 Ix cm4 Remarks
Property Ratio e Ratio
1 L20206LD 0.539 1 8 17.677 39.885 125.626 5.346 Passed
7 L20206LD 0.189 1 8 17.677 39.885 125.626 5.346 Passed
8 L20206LD 0.29 1 9 17.677 39.885 125.626 5.346 Passed
9 L20206LD 0.413 1 9 17.677 39.885 125.626 5.346 Passed
10 L20206LD 0.24 1 7 17.677 39.885 125.626 5.346 Passed
11 L20206LD 0.112 1 7 17.677 39.885 125.626 5.346 Passed
12 L20206LD 0.195 1 6 17.677 39.885 125.626 5.346 Passed
13 L20203 LDLD 0.519 1 6 9.316 22.731 61.327 0.708 Passed
14 L20206LD 0.886 1 9 17.677 39.885 125.626 5.346 Passed
15 L20203 LDLD 0.272 1 7 9.316 22.731 61.327 0.708 Passed
18 L20203 LDLD 0.038 1 8 9.316 22.731 61.327 0.708 Passed
19 L20203 LDLD 0.062 1 8 9.316 22.731 61.327 0.708 Passed
20 L20203 LDLD 0.062 1 8 9.316 22.731 61.327 0.708 Passed
21 L20203 LDLD 0.075 1 9 9.316 22.731 61.327 0.708 Passed
22 L20203 LDLD 0.089 1 9 9.316 22.731 61.327 0.708 Passed
23 L20203 LDLD 0.124 1 7 9.316 22.731 61.327 0.708 Passed
25 L20203 LDLD 0.11 1 7 9.316 22.731 61.327 0.708 Passed
26 L20206LD 0.388 1 7 17.677 39.885 125.626 5.346 Passed
27 L20206LD 0.383 1 7 17.677 39.885 125.626 5.346 Passed
28 L20206LD 0.459 1 7 17.677 39.885 125.626 5.346 Passed
29 L20206LD 0.209 1 9 17.677 39.885 125.626 5.346 Passed
38 L20206LD 0.61 1 7 17.677 39.885 125.626 5.346 Passed
39 L20206LD 0.369 1 7 17.677 39.885 125.626 5.346 Passed
42 L20203 LDLD 0.016 1 5 9.316 22.731 61.327 0.708 Passed
44 L20203 LDLD 0.021 1 8 9.316 22.731 61.327 0.708 Passed
45 L20203 LDLD 0.183 1 7 9.316 22.731 61.327 0.708 Passed
46 L20203 LDLD 0.073 1 7 9.316 22.731 61.327 0.708 Passed
47 L20203 LDLD 0.251 1 7 9.316 22.731 61.327 0.708 Passed
48 L20203 LDLD 0.436 1 7 9.316 22.731 61.327 0.708 Passed
49 L20203 LDLD 0.279 1 9 9.316 22.731 61.327 0.708 Passed
50 L20203 LDLD 0.263 1 9 9.316 22.731 61.327 0.708 Passed
51 L20203 LDLD 0.246 1 9 9.316 22.731 61.327 0.708 Passed
61 L20206LD 0.535 1 8 17.677 39.885 125.626 5.346 Passed
62 L20206LD 0.266 1 8 17.677 39.885 125.626 5.346 Passed
63 L20206LD 0.14 1 9 17.677 39.885 125.626 5.346 Passed
64 L20206LD 0.111 1 7 17.677 39.885 125.626 5.346 Passed
65 L20206LD 0.134 1 8 17.677 39.885 125.626 5.346 Passed
66 L20206LD 0.849 1 9 17.677 39.885 125.626 5.346 Passed
67 L20206LD 0.596 1 9 17.677 39.885 125.626 5.346 Passed
68 L20206LD 0.48 1 9 17.677 39.885 125.626 5.346 Passed
69 L20206LD 0.365 1 9 17.677 39.885 125.626 5.346 Passed
70 L20206LD 0.295 1 9 17.677 39.885 125.626 5.346 Passed
71 L20203 LDLD 0.233 1 9 9.316 22.731 61.327 0.708 Passed
72 L20203 LDLD 0.221 1 9 9.316 22.731 61.327 0.708 Passed
73 L20203 LDLD 0.216 1 8 9.316 22.731 61.327 0.708 Passed
74 L20203 LDLD 0.207 1 8 9.316 22.731 61.327 0.708 Passed
STRUCTURAL CALCULATION
Poject: Design of Steel Trusss
Location: Romblon
75 L20203 LDLD 0.095 1 9 9.316 22.731 61.327 0.708 Passed

You might also like