User Manual

·Instruction diagram
Side A

LED 1
Buzzer
LED 2
LED 3
LED 4
LED 5
Microphone

TX VCC+ (5-15V)
RX GND
GND Video
Audio
LED 1: Blue ——WiFi status light
LED 2: Green ——Photo mode status light
LED 3: Blue —— Video mode status light
LED 4: Orange —— OSD Setup status light
LED 5: Red —— Power status light, it's always on after being powered
Side B

WiFi/Mode Switch Button

Micro-USB
Power/Shutter Button

Sensor connector WiFi module connector

·Installation Diagram

USB
DC 5V

Warning:
USB port only supports DC 5V

·MicroSD Card
Capacity up to 64GB; Please use high speed cards(Class10/UHS-I/UHS-II).

Please push the metal piece a little bit up with one hand like showed in above step 1
and then press the SD card(step 2) with another hand to let the card pop out.

·Lens module connection diagram

1 2

2 1
OPEN LOCK
Warning: Please push upward the black locking arm before you unplug the lens cable in
case the connector is destroyed. And Golden fingers on ends of the lens cable
should face to the opposite of each other. For more details about how to
connect the lens cable properly, you may refer to: https://goo.gl/PoGg1T

·Basic Camera Operation

Powering On/Off Long press the Power/Shutter button
WiFi On/Off Short press the WiFi/Mode Switch button
After powering on, long press the WiFi/Mode Switch button to cycle
Mode Switching
through the three modes: Video/Photos/OSD settings.

Camera Status Light: Blue (LED 3)

Video Mode
• Press the Power/Shutter button to start/stop recording.

Camera Status Light: Green (LED 2)

Photo Mode
• Press the Power/Shutter button to capture photos.

Camera Status Light: Orange (LED 4)

• Press the Power/Shutter button to move to a setting.
OSD Setup Mode
• Press the WiFi/Mode Switch button to select.
• Long press the WiFi/Mode Switch button to exit the menu.

Simultaneously press the Power/Shutter button and

Forced Shutdown
WiFi/Mode Switch button.

In standby mode, press the WiFi/Mode Switch button three times in rapid
Reset succession (within 2 seconds). When resetting is complete, the status
light (orange) blicks twice, and the camera automatically shuts down.

Note: Recording automatically after turing on by default, with the V1.0 firmware, under
the video status, short press WIFI/MODE SWITCH button to pause/start the
recording. With the V1.1 and later firmware, under the video status, short press
WIFI/MODE SWITCH button to stop the recording and turn on the WIFI; Under the
standby mode, the function of the WIFI/MODE SWITCH button doesn't change.

·Transmitter connection diagram

Method One (Recommended): connect by the soldering pads

Video Transmitter

PDB

Power in
GND
5-15V 5-15V GND
Video
Audio

Methos Two: connect by the TV-out and power USB cable

Video Transmitter

PDB

5V Power in
GND GND
GND
Video

Warning: USB port only supports DC 5V

·Flight Controller Set

Preparation
· Firmware: CleanFlight (≥2.1.0) / BetaFlight (≥3.2.0)
· Any available UART interface on the Flight Controller
1. Connect the RunCam Split 2 with the UART interface of the Flight Controller

FC
UART Interface

GND GND
RX TX
TX RX

2. Make the Flight Controller recognize the RunCam Split 2

For example, we connect the RunCam Split 2 to the UART 3 interface on the Flight
Controller: connect the Flight Controller to the computer, then open the configurator
software of the Flight Controller. (Open up the configurator that matches the firmware
you are running, Betaflight Configurator for Betaflight, Cleanflight Configurator for
Cleanflight). In the Peripherals column of the line UART3 (on the Ports tab), select
RunCam Device and click Save And Reboot.

3. Instructions
Insttructtions off tthe
he ffunctions
uncttions off the
the camera and
d assigning
assiigniing transmitter
transmiitter
channels to them
In the Flight Controller Configurator, navigate to the Modes tab. There are new
CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes.
· CAMERA WI-FI: turn on/off the WIFI of the camera. When in the OSD of the camera, this
is used to confirm your selection.
· CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to
move to the next menu item.
· CAMERA CHANGE MODE: switch among the three modes, video, photo and OSD
setting mode. When in the OSD of the camera, this will exit the menu.
Assign any available channel to the function you need, for example:
· Assign the AUX1 to the CAMERA WI-FI, range 1900-2100
· Assign the AUX2 to the CAMERA POWER, range 1900-2100
· Assign the AUX3 to the CAMERA CHANGE MODE, range 1900 1900-2100
2100

4. Assign
4 Assiign tthe
he channel
hannell to
ch to tthe switch
he swi h off tthe
itch controller
he cont
trolller
Please choose your Model on the controller, then access to the MIXER interface and
assign the channel to the switch of the controller. Take opentx 2.2.0 for example, assign
the channels CH5, CH6 and CH7 to SA, SB and SD respectively.

5. Test
Power the Flight Controller and the RunCam Split 2
· Set the SA to the bottom, the camera starts/stops the video
· Set the SB to the bottom, the camera turns on/off the WIFI
· Set the SD to the bottom, the camera switches among the three modes: video, photo
and OSD setting mode

·App(Android | iOS)
Search 'RunCam App' on Google Play/Apple Store, or download on our website:
https://www.runcam.com/download/runcamsplit2
Default SSID: RCSplit_ ****** (* for letters or numbers)
Default WiFi password: 1234567890

·Technical Support
Please visit: https://support.runcam.com

·Parameter
Field of View (FOV) FPV FOV 130°/Recording FOV 165°
Video Resolution 1080@60fps/1080@30fps/720@60fps
Video File Format MOV
Image Resolution 2 Megapixels
TV Mode NTSC (720*480)/PAL (720*576) Switchable
Real-Time Audio Output Yes
Interface Micro USB / UART
Max Micro SD Card Supported 64G(need Class 6 or above,
recommend Class 10/UHS-I/UHS-II/UHS-III)
WiFi Module Support (Removable)
Dimensions PCB 38*38mm/Lens Module 22*20mm
Power Input DC 5-15V / DC 5V(USB)
Working Current 650mA @5V/270mA @12V
Weight 21g/23g (Plus WiFi Module)

www.runcam.com