RunCam Swift 2

USER MANUAL
Connection
* Unplug the 5D-OSD menu cable after OSD setting.
Transmitter

2 pin extension cord

Power in
GND
5-36V

5-36V in

UP
GND
To VBAT+
L R Video out
DOWN
Audio out
5D-OSD menu cable VBAT+
Dimensions & Installation

28.5mm 1 Nylon Gaskets 2 M2*4 Screws

3 M3*5 Screws 4 M3 Non-slip Nuts

26mm

2 3 3
2
5-36V

26mm

1 1

4 4 1 1
OSD Menu
OSD Setting: Press and hold the UP button for 2 seconds to enter OSD setup menu.
Customize the PILOT name: Use the UP,
RunCam
DOWN, LEFT and RIGHT buttons to
1234567890ABCDEFG navigate through the letters and
HIJKLMNOPQRSTUVWX confirm with the CENTER button.
YZa b c d e f g h i j k l m n o
pqrstuvwxyz.-:/@ Quick settings:
PILOT ON Long press the LEFT/DOWN/RIGHT
TIMER ON button for 2 seconds to activate the
VOLTAGE ON VOLTAGE/PILOT/TIMER, then you can use
the UP, DOWN, LEFT and RIGHT buttons
BASELINE OFF
to move it to the appropriate location on
DEFAULT
the screen, and press the CENTER button
EXIT to exit.
· PILOT: ON/OFF
· TIMER: ON/OFF The OSD displays by default the input
· VOLTAGE: ON/OFF voltageof the camera. If the VBAT + cable
is connected to the battery's positive side,
· BASELINE: OFF/1-9
it displays the battery voltage instead.
· EXIT: Save the current settings and exit
OSD Menu
· Voltage Calibration
· Press and hold the RIGHT button for 2
seconds to select the voltage
· Press and hold the CENTER button for 2
seconds, the voltage starts to flash, now
you can adjust the voltage:
· Increase(LEFT button) or reduce
(RIGHT button) 0.1V each press.
Maximum adjustment range: ± 1v
· After adjustment, press the CENTER
button to select the voltage, then press
it again to save and exit.
16.8v RunCam 01:08
Camera Menu
· MAIN MENU · EXPOSURE

SETUP EXPOSURE
CAM TITLE OFF SHUTTER AUTO
EXPOSURE BRIGHTNESS 050
BACKLIGHT AGC OFF
WHITE BAL ATW1 DWDR ON
DAY & NIGHT COLOR RETURN RET
IMAGE ADJ
DPC
LANGUAGE ENGLISH
RESET
EXIT

· CAM TITLE (ON/OFF) · SHUTTER (AUTO / 50-100000 / FLK)

· LANGUAGE (English/中文) · BRIGHTNESS (50 / 0-255)
· WHITE BAL (ATW1 / ATW2 / AWC→ SET / · AGC (OFF / LOW / MIDDLE / HIGH)
MANUAL: MANUAL, INDOOR, OUTDOOR) · DWDR (ON: 63 0-63 / OFF)
· DPC (Cover the lens then press enter key)
Camera Menu
· IMAGE ADJ

IMAGE ADJ USER ADJ.

LENS SHAD OFF GAMMA 0.50
2DNR OFF PED LEVEL 017
MIRROR OFF COLOR GAIN 176
FONT COLOR RETURN RET
CONTRAST 110
SHARPNESS 026
DISPLAY USER
NEG IMAGE OFF
RETURN

· LENS SHAD (OFF/ ON:22 0-255) · GAMMA (0.5 / 0.05-1.0)

· CONTRAST (110 / 0-255) · PED LEVEL (17 / 0-63)
· SHARPNESS (26 / 0-31) · COLOR GAIN (176 / 0-255)
· DISPLAY (CRT/LCD/USER)
Camera Menu
· BACKLIGHT (BLC / HLC / OFF)

BLC HLC
AREA SEL AREA1 LEVEL 200
AREA STATE ON MODE ALL DAY
GAIN 042 RETURN RET
HEIGHT 004
WIDTH 003
LEFT/RIGHT 006
TOP/BOTTOM 005
RETURN RET

· AREA SEL (AREA1/AREA2) · LEVEL (200 / 0-255)

· GAIN (042 / 0-255 ) · MODE (ALL DAY / NIGHT ONLY )
· HEIGHT (4 / 0-10)
· WIDTH (3 / 0-9)
· LEFT/RIGHT (6 / 0-6)
· TOP/BOTTOM (10 / 0-10)
Camera Menu
· DAY & NIGHT (AUTO / COLOR / B&W / EXT)

D & N AUTO D&N B&W

D N LEVEL 080 BURST OFF
D N DELAY 3 SEC IR SMART OFF
N D LEVEL 032 IR LEVEL HIGH
N D DELAY 1 SEC RETURN RET
RETURN RET

· DAY NIGHT LEVEL (80 / 0-176) · BURST (OFF/ON)

· DAY NIGHT DELAY (3 / 1-30) · IR SMART (OFF/ON)
· NIGHT DAY LEVEL (032 / 0-255) · IR LEVEL (HIGH/LOW)
· NIGHT DAY DELAY (1 / 1-30)
Model RunCam Swift 2
Image Sensor 1/3″SONY SUPER HAD II CCD
Horizontal Resolution 600TVL
Lens 2.5mm (Default) / 2.3mm / 2.1mm
Signal System PAL/NTSC
Integrated OSD Yes
Integrated MIC Yes
S/N Ratio >60dB (AGC OFF)
Electronic Shutter Speed PAL: 1/50~100,000; NTSC: 1/60~100,000
Auto Gain Control (AGC) Yes
Back Light Compensation (BLC) Yes
Min. Illumination [email protected]
WDR D-WDR
DNR 2DNR
Day/Night Color/Auto/B&W
Power DC 5-36V
Net Weight 14g
Dimensions 28.5mm*26mm*26mm