Scribd
Upload
76 views4 pages

Assignment 3

This document contains assignments for different student roll numbers on the topics of electrical and electronics engineering. It includes questions on transistor biasing circuits, characteristics of BJT, rectifier circuits, zener regulators, and use of transistors as switches. Students are asked to calculate voltage, current, efficiency values for given rectifier circuits, and to explain concepts like dc load lines, biasing methods, and diode/transistor characteristics. The assignments must be submitted by a given deadline.

Uploaded by

Manasi Jain
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
76 views4 pages

Assignment 3

This document contains assignments for different student roll numbers on the topics of electrical and electronics engineering. It includes questions on transistor biasing circuits, characteristics of BJT, rectifier circuits, zener regulators, and use of transistors as switches. Students are asked to calculate voltage, current, efficiency values for given rectifier circuits, and to explain concepts like dc load lines, biasing methods, and diode/transistor characteristics. The assignments must be submitted by a given deadline.

Uploaded by

Manasi Jain
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Assignment-03(Continuous Assessment) – Janaury-2021 Ist

Semester B.Tech. (2020-21) Subject: - Basics of Electrical and


Electronics Engineering (Subject code:20BTEC005)
Division –CSE ‘C”

Assignment-III
Last Date of Submission: 13/01/2021- 11:30pm
Roll No:01-10 (121-130)
1) What do you mean by dc load line of a transistor? What is
meant by Q point?
2) What is need of biasing a transistor?
3) Describe fixed biased, collector to base bias and voltage
divider bias circuits with circuit diagram.
4) Draw and describe input and output characteristics of BJT?
What is Early effect in BJT?
5) Half wave rectifier has turns ratio 4:1 with input 240V, 50 Hz
supply, Forward resistance of diode (RF)=10Ω, secondary
resistance(RS)= 80Ω and load resistance (RL)=1KΩ. Calculate
VDC, VRMS, IDC & IRMS and rectification efficiency.
Roll No:11-20 (131-140)
1) What is difference between photo diode and LED?
2) Explain V-I characteristics of PN junction diode ,also explain
current equation and describe reverse saturation current.
3) Draw and describe construction, working of zener diode,
tunnel diode, varactor diode.
4) Compare Half wave rectifier , full wave centre tap rectifier and
bridge rectifier with respect to VDC, VRMS, IDC, IRMS ,ripple
factor ,TUF,PIV Also draw input and output voltage waveforms.
5) Full wave center tapped rectifier has turns ratio 2:1 with input
230V, 50 Hz supply, Forward resistance of diode (RF)=1Ω,
secondary resistance(RS)= 50Ω and load resistance (RL)=2KΩ.
Calculate VDC, VRMS, IDC& IRMS and rectification efficiency.

Roll No:31-40 (151-160)


1) Draw and describe working of bridge rectifier and derive
equations for VDC, VRMS, IDC & IRMS. Also draw input and
output voltage waveforms.
2) Draw and describe construction, working of zener diode, tunnel
diode, varactor diode.
3) Input=5VRMS, Diodes=silicon diodes, load resistor=2.2 KΩ,
calculate, VDC, VRMS, IDC & IRMS, TUF, FF, & rectification
efficiency of half wave rectifier.
4) Differentiate between CB, CE and CC configurations.
5) Design and draw Zener shunt regulator circuit to meet
following specifications- VL=8V, Vin=30V, IL=50mA,
Izmin=5mA, Pz=1 Watt. Calculate RLmin, RLmax, & R.

Roll No:41-50
1. Draw and describe working of full wave centre tap rectifier and
derive equations for VDC, VRMS, IDC,& IRMS, TUF, FF &
rectification efficiency. Also draw input and output voltage
waveforms.
2. Draw and describe circuit diagram of zener diode as a shunt
voltage regulator.
3. Explain BJT as a switch. Why CB and CC configurations are
not preferred.
4. Explain input output characteristics of CE amplifier.
5. Bridge rectifier has turns ratio 4:1 with input 230V, 50 Hz
supply, Forward resistance of diode (RF)=1Ω, secondary
resistance(RS)= 40Ω and load resistance (RL)=3KΩ. Calculate
VDC, VRMS, IDC & IRMS and rectification efficiency.

Roll No:51-60
1) Explain working of transistor as a switch
2) What is difference between tunnel diode and PN diode?
3) Draw waveforms for output voltage, diode voltage, diode
current and input voltage of bridge rectifier circuit. Assume
silicon diodes.
4) Sketch the CE output characteristics and indicate the active,
saturation and cut-off regions.
5) Full wave centre tapped rectifier has turns ratio 2:1 with input
230V, 50 Hz supply, Forward resistance of diode (RF)=1Ω,
secondary resistance(RS)= 50Ω and load resistance (RL)=2KΩ.
Calculate VDC, VRMS, IDC & IRMS and rectification
efficiency.
Roll No:61-77
1) Explain V-I characteristics of PN junction diode ,also explain
current equation and describe reverse saturation current.
2) Draw and describe construction, working of zener diode, tunnel
diode, varactor diode.
3) Explain BJT as a switch. Why CB and CC configurations are
not preferred.
4) Explain input output characteristics of CE amplifier.
5) Full wave centre tapped rectifier has turns ratio 2:1 with input
230V, 50 Hz supply, Forward resistance of diode (RF)=1Ω,
secondary resistance(RS)= 50Ω and load resistance (RL)=2KΩ.
Calculate VDC, VRMS, IDC& IRMS and rectification efficiency.

You might also like