PENGUJIAN LENTUR BALOK BETON KARET (BEAM)

VARIASI 1 (PSR 60%: KRT 40%)

Tgl. Pengujian : 26 - 08 - 2013

Balok 1 Balok 2 Balok 3

No
(ΔL) mm P (kN) (ΔL) mm P (kN) (ΔL) mm P (kN)
0.01 0.05 0.01 0.05 0.01 0.05
1 11 0.25 9.5 0.25 13 0.25
2 17 0.50 13 0.50 16 0.50
3 22 0.75 16 0.75 18 0.75
4 28 1.00 20 1.00 21 1.00
5 33 1.25 24 1.25 23 1.25
6 38 1.50 28 1.50 25 1.50
7 42 1.75 31.5 1.75 25 1.75
8 46 2.00 35 2.00 15 2.00
9 47 2.25 36 2.25 11 2.25
10 49 2.50 39 2.50 14 2.50
11 53 2.75 43 2.75 17 2.75
12 56 3.00 46 3.00 20 3.00
13 59 3.25 48 3.25 23 3.25
14 62 3.50 51 3.50 26 3.50
15 64 3.75 54 3.75 29 3.75
16 67 4.00 57 4.00 32 4.00
17 70 4.25 59 4.25 36 4.25
18 73 4.50 62 4.50 38 4.50
19 74.5 4.75 64 4.75 41 4.75
20 78 5.00 65 5.00 44 5.00
22 80 5.25 67 5.25 45 5.25
24 82 5.50 69.5 5.50 45.5 5.50
26 85 5.75 71 5.75 47 5.75
28 87 6.00 72.5 6.00 48 6.00
30 89 6.25 74 6.25 52 6.25
32 91 6.50 76 6.50 53 6.50
34 93.5 6.75 77 6.75 56 6.75
36 96 7.00 80 7.00 60 7.00
38 99 7.25 82 7.25 63 7.25
40 102 7.50 83 7.50 65 7.50
42 105 7.75 86 7.75 69 7.75
44 108 8.00 89 8.00 72 8.00
46 112 8.25 92 8.20 75 8.25
48 120 8.00 210 1.00 80 8.50
50 190 7.00 410 0.50 100 8.60
52 500 0.25 320 1.00
54 770 0.10 450 0.75
56 1000 0.05 670 0.50
58 720 0.30
60 850 0.25
62 1050 0.10
64
66
68
70
72
74
76
78
80
82
84
86
88
90
 PENGUJIAN LENTUR BALOK BETON KARET (BEAM)
VARIASI 2 (PSR 70%: KRT 30%)

Tgl. Pengujian : 27 - 08 - 2013

Balok 4 Balok 5 Balok 6

No
(ΔL) mm P (kN) (ΔL) mm P (kN) (ΔL) mm P (kN)
0.01 0.05 0.01 0.05 0.01 0.05
1 60 0.25 6 0.25 8 0.25
2 70 0.50 8 0.50 12 0.50
3 75 0.75 10 0.75 15 0.75
4 79 1.00 12 1.00 19 1.00
5 83 1.25 13 1.25 21.5 1.25
6 87 1.50 15 1.50 24 1.50
7 91 1.75 18 1.75 27 1.75
8 96 2.00 21 2.00 30 2.00
9 98 2.25 24 2.25 34 2.25
10 105 2.50 27 2.50 36 2.50
11 107 2.75 30 2.75 39 2.75
12 111 3.00 34 3.00 42 3.00
13 114 3.25 36 3.25 45 3.25
14 118 3.50 40 3.50 49 3.50
15 122 3.75 43 3.75 52 3.75
16 125 4.00 47 4.00 54.5 4.00
17 127.5 4.25 49 4.25 57 4.25
18 131 4.50 52 4.50 60 4.50
19 132.5 4.75 55 4.75 63 4.75
20 135 5.00 58 5.00 65 5.00
22 137 5.25 60 5.25 67 5.25
24 139 5.50 62 5.50 68 5.50
26 142 5.75 64 5.75 70 5.75
28 144 6.00 66 6.00 71 6.00
30 146 6.25 67 6.25 73 6.25
32 148 6.50 70 6.50 75 6.50
34 149 6.75 71 6.75 76.5 6.75
36 151 7.00 73 7.00 78 7.00
38 153 7.25 75 7.25 80 7.25
40 154 7.50 76 7.50 81 7.50
42 156 7.75 78 7.75 83 7.75
44 157 8.00 79.5 8.00 84 8.00
46 159 8.25 81 8.25 86 8.25
48 160.5 8.50 82 8.50 87 8.50
50 162 8.75 84 8.75 88 8.75
52 163 9.00 85 9.00 89 9.00
54 165 9.25 87 9.25 91 9.25
56 166 9.50 88.5 9.50 92 9.50
58 168 9.75 90 9.75 94 9.75
60 169 10.00 91 10.00 95 10.00
62 170 10.25 92 10.25 97 10.30
64 171.5 10.50 94 10.50 100 9.50
66 173 10.75 95 10.75 240 1.00
68 175 11.00 97 11.00 650 0.50
70 290 11.25 99 11.25 700 0.25
72 740 0.50 100 11.50
74 1170 0.25 102 11.75
76 104 12.00
78 115 11.50
80 300 0.50
82 320 0.25
84
86
88
90
 PENGUJIAN LENTUR BALOK BETON KARET (BEAM)
VARIASI 3 (PSR 80%: KRT 20%)

Tgl. Pengujian : 27 - 08 - 2013

Balok 7 Balok 8 Balok 9

No
(ΔL) mm P (kN) (ΔL) mm P (kN) (ΔL) mm P (kN)
0.01 0.05 0.01 0.05 0.01 0.05
1 26 0.25 8 0.25 6 0.25
2 29 0.50 11 0.50 8 0.50
3 31 0.75 14 0.75 10 0.75
4 33 1.00 17 1.00 12 1.00
5 36 1.25 19 1.25 14 1.25
6 38 1.50 22 1.50 16 1.50
7 40 1.75 24 1.75 18 1.75
8 42 2.00 27 2.00 20 2.00
9 43 2.25 29 2.25 24 2.25
10 45 2.50 31 2.50 24.5 2.50
11 48 2.75 32.5 2.75 25 2.75
12 51 3.00 35 3.00 29 3.00
13 53 3.25 38 3.25 33 3.25
14 57 3.50 39 3.50 38 3.50
15 59 3.75 41 3.75 41 3.75
16 62 4.00 43 4.00 45 4.00
17 64 4.25 48 4.25 48 4.25
18 67 4.50 50 4.50 51 4.50
19 69 4.75 52 4.75 55 4.75
20 72 5.00 54.5 5.00 59 5.00
22 73 5.25 57 5.25 63 5.25
24 75 5.50 58 5.50 65 5.50
26 77 5.75 59 5.75 66 5.75
28 79 6.00 61 6.00 68 6.00
30 80 6.25 62 6.25 70 6.25
32 81 6.50 63 6.50 71 6.50
34 82 6.75 64.5 6.75 73 6.75
36 83 7.00 65 7.00 74 7.00
38 84.5 7.25 67 7.25 76 7.25
40 85 7.50 68 7.50 77 7.50
42 86 7.75 69 7.75 79 7.75
44 87 8.00 70 8.00 81 8.00
46 88 8.25 71 8.25 83 8.25
48 89 8.50 72 8.50 84 8.50
50 90 8.75 73 8.75 85 8.75
52 90.5 9.00 74 9.00 86 9.00
54 91.0 9.25 75 9.25 88 9.25
56 92 9.50 76.5 9.50 89 9.50
58 93 9.75 78 9.75 90 9.75
60 94 10.00 79 10.00 91.5 10.00
62 95 10.25 80.5 10.25 93 10.25
64 96 10.50 81 10.50 94 10.50
66 96.5 10.75 100 10.75 95 10.75
68 97.5 11.00 147 11.00 96 11.00
70 98 11.25 149 11.25 97 11.25
72 99 11.50 151 11.50 98 11.50
74 100 11.75 152 11.75 99 11.75
76 101 12.00 155 12.00 100 12.00
78 102 12.25 157.5 12.25 101 12.25
80 104 12.50 200 12.30 102 12.50
82 200 0.50 300 0.50 103 12.75
84 360 0.25 340 0.25 104 13.00
86 105 13.25
88 200 13.35
90 0 0.00
 PENGUJIAN LENTUR BALOK BETON KARET (BEAM)
VARIASI 4 (PSR 90%: KRT 10%)

Tgl. Pengujian : 28 - 08 - 2013

Balok 10 Balok 11 Balok 12

No
(ΔL) mm P (kN) (ΔL) mm P (kN) (ΔL) mm P (kN)
0.01 0.05 0.01 0.05 0.01 0.05
1 4 0.25 9 0.25 4 0.25
2 7 0.50 15 0.50 8 0.50
3 11 0.75 20 0.75 12.5 0.75
4 17 1.00 26 2.00 14 1.00
5 25 1.25 32 2.50 26 1.25
6 31 1.50 41 3.00 28 3.00
7 37 1.75 48 3.50 29 3.50
8 44 4.00 54 4.00 31 4.00
9 47 4.50 59 4.50 33 4.50
10 52 5.00 62 5.00 40 5.00
11 54 5.50 64 5.50 41 5.50
12 58 6.00 67 6.00 42 6.00
13 60 6.50 70 6.50 42.5 6.50
14 63 7.00 72 7.00 45 7.00
15 65 7.50 74 7.50 47 7.50
16 67 8.00 77 8.00 44 8.00
17 69 8.50 78 8.50 51 8.50
18 70 9.00 80 9.00 52.5 9.00
19 72 9.50 82.5 9.50 54 9.50
20 73 10.00 84 10.00 56 10.00
22 74 10.50 86 10.50 57 10.50
24 76 11.00 88 11.00 59 11.00
26 77 11.50 89 11.50 60 11.50
28 78 12.00 91 12.00 62 12.00
30 80 12.50 93 12.50 63 12.50
32 81 13.00 95 13.00 64 13.00
34 83 13.50 96 13.50 66 13.50
36 85 14.00 98 14.00 68 14.00
38 86 14.50 100 14.50 100 14.20
40 87 15.00 101 15.00
42 89 15.50 102.5 15.50
44 90 16.00 104 16.00
46 91 16.50 105 16.50
48 92 17.00 107 17.00
50 100 17.10 108 17.50
52 120 18.00
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
 PENGUJIAN LENTUR BALOK BETON KARET (BEAM)
VARIASI 5 (PSR 100%: KRT 0%)

Tgl. Pengujian : 28 - 08 - 2013

Balok 13 Balok 14 Balok 15

No
(ΔL) mm P (kN) (ΔL) mm P (kN) (ΔL) mm P (kN)
0.01 0.05 0.01 0.05 0.01 0.05
1 6 0.50 4 0.50 5 0.50
2 11 1.00 8 1.00 9 1.00
3 16 1.50 12 1.50 13 1.50
4 19 2.00 16 2.00 17 2.00
5 23 2.50 20 2.50 22 2.50
6 27 3.00 23 3.00 26 3.00
7 32 3.50 30 3.50 31 3.50
8 37 4.00 35 4.00 36 4.00
9 40 4.50 38 4.50 40 4.50
10 44 5.00 42 5.00 44 5.00
11 47 5.50 46 5.50 48 5.50
12 51 6.00 49 6.00 52 6.00
13 53 6.50 53 6.50 54 6.50
14 55 7.00 55 7.00 57 7.00
15 58 7.50 57 7.50 59 7.50
16 60 8.00 59 8.00 61 8.00
17 62 8.50 60 8.50 63 8.50
18 64 9.00 62 9.00 65 9.00
19 66 9.50 64 9.50 67 9.50
20 67 10.00 66 10.00 69 10.00
22 69 10.50 68 10.50 71 10.50
24 71 11.00 69.5 11.00 73 11.00
26 73 11.50 71 11.50 75 11.50
28 74 12.00 72.5 12.00 77 12.00
30 76 12.50 74 12.50 78 12.50
32 77 13.00 76 13.00 80 13.00
34 79 13.50 77 13.50 82 13.50
36 80 14.00 79 14.00 83.5 14.00
38 82 14.50 80 14.50 85 14.50
40 84 15.00 82 15.00 87 15.00
42 86 15.50 83 15.50 88 15.50
44 88 16.00 85 16.00 90 16.00
46 87 16.50 92 16.50
48 88 17.00 110 16.60
50 100 17.30
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
 HUBUNGAN TEGANGAN REGANGAN HASIL PENGUJIAN KUAT LENTUR
VARIASI I (PASIR 60% : KARET 40%)

Jenis Benda Uji = Balok 1 Jenis Benda Uji = Balok 2 Jenis Benda Uji = Balok 3
Kode Benda Uji = Variasi 1 (Psr 60% : Karet 40%) Kode Benda Uji = Variasi 1 (Psr 60% : Karet 40%) Kode Benda Uji = Variasi 1 (Psr 60% : Karet 40%)
Panjang (L) = 500 mm Panjang (L) = 500 mm Panjang (L) = 500 mm
Lebar (b) = 153.7 mm Lebar (b) = 150.3 mm Lebar (b) = 153.4 mm
Tinggi (h) = 151.6 mm Tinggi (h) = 153.2 mm Tinggi (h) = 150.2 mm
1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm
Faktor beban = 0.05 KN Faktor beban = 0.05 KN Faktor beban = 0.05 KN
Regangan = Δh / ho Regangan = Δh / ho Regangan = Δh / ho
Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2)

Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan
No No No
Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa)
11 0.11 0.00073 0.25 250 0.035 9.5 0.10 0.00062 0.25 250 0.035 13 0.13 0.00087 0.25 250 0.036
17 0.17 0.00112 0.50 500 0.071 13 0.13 0.00085 0.50 500 0.071 16 0.16 0.00107 0.50 500 0.072
22 0.22 0.00145 0.75 750 0.106 16 0.16 0.00104 0.75 750 0.106 18 0.18 0.00120 0.75 750 0.108
28 0.28 0.00185 1.00 1000 0.142 20 0.20 0.00131 1.00 1000 0.142 21 0.21 0.00140 1.00 1000 0.144
33 0.33 0.00218 1.25 1250 0.177 24 0.24 0.00157 1.25 1250 0.177 23 0.23 0.00153 1.25 1250 0.181
38 0.38 0.00251 1.50 1500 0.212 28 0.28 0.00183 1.50 1500 0.213 25 0.25 0.00166 1.50 1500 0.217
42 0.42 0.00277 1.75 1750 0.248 31.5 0.32 0.00206 1.75 1750 0.248 25 0.25 0.00166 1.75 1750 0.253
46 0.46 0.00303 2.00 2000 0.283 35 0.35 0.00228 2.00 2000 0.283 15 0.15 0.00100 2.00 2000 0.289
47 0.47 0.00310 2.25 2250 0.318 36 0.36 0.00235 2.25 2250 0.319 11 0.11 0.00073 2.25 2250 0.325
49 0.49 0.00323 2.50 2500 0.354 39 0.39 0.00255 2.50 2500 0.354 14 0.14 0.00093 2.50 2500 0.361
53 0.53 0.00350 2.75 2750 0.389 43 0.43 0.00281 2.75 2750 0.390 17 0.17 0.00113 2.75 2750 0.397
56 0.56 0.00369 3.00 3000 0.425 46 0.46 0.00300 3.00 3000 0.425 20 0.20 0.00133 3.00 3000 0.433
59 0.59 0.00389 3.25 3250 0.460 48 0.48 0.00313 3.25 3250 0.461 23 0.23 0.00153 3.25 3250 0.470
62 0.62 0.00409 3.50 3500 0.495 51 0.51 0.00333 3.50 3500 0.496 26 0.26 0.00173 3.50 3500 0.506
64 0.64 0.00422 3.75 3750 0.531 54 0.54 0.00352 3.75 3750 0.532 29 0.29 0.00193 3.75 3750 0.542
67 0.67 0.00442 4.00 4000 0.566 57 0.57 0.00372 4.00 4000 0.567 32 0.32 0.00213 4.00 4000 0.578
70 0.70 0.00462 4.25 4250 0.602 59 0.59 0.00385 4.25 4250 0.602 36 0.36 0.00240 4.25 4250 0.614
73 0.73 0.00482 4.50 4500 0.637 62 0.62 0.00405 4.50 4500 0.638 38 0.38 0.00253 4.50 4500 0.650
74.5 0.75 0.00491 4.75 4750 0.672 64 0.64 0.00418 4.75 4750 0.673 41 0.41 0.00273 4.75 4750 0.686
78 0.78 0.00515 5.00 5000 0.708 65 0.65 0.00424 5.00 5000 0.709 44 0.44 0.00293 5.00 5000 0.722
80 0.80 0.00528 5.25 5250 0.743 67 0.67 0.00437 5.25 5250 0.744 45 0.45 0.00300 5.25 5250 0.759
82 0.82 0.00541 5.50 5500 0.779 69.5 0.70 0.00454 5.50 5500 0.780 45.5 0.46 0.00303 5.50 5500 0.795
85 0.85 0.00561 5.75 5750 0.814 71 0.71 0.00463 5.75 5750 0.815 47 0.47 0.00313 5.75 5750 0.831
87 0.87 0.00574 6.00 6000 0.849 72.5 0.73 0.00473 6.00 6000 0.850 48 0.48 0.00320 6.00 6000 0.867
89 0.89 0.00587 6.25 6250 0.885 74 0.74 0.00483 6.25 6250 0.886 52 0.52 0.00346 6.25 6250 0.903
91 0.91 0.00600 6.50 6500 0.920 76 0.76 0.00496 6.50 6500 0.921 53 0.53 0.00353 6.50 6500 0.939
93.5 0.94 0.00617 6.75 6750 0.955 77 0.77 0.00503 6.75 6750 0.957 56 0.56 0.00373 6.75 6750 0.975
96 0.96 0.00633 7.00 7000 0.991 80 0.80 0.00522 7.00 7000 0.992 60 0.60 0.00399 7.00 7000 1.011
99 0.99 0.00653 7.25 7250 1.026 82 0.82 0.00535 7.25 7250 1.028 63 0.63 0.00419 7.25 7250 1.047
102 1.02 0.00673 7.50 7500 1.062 83 0.83 0.00542 7.50 7500 1.063 65 0.65 0.00433 7.50 7500 1.084
105 1.05 0.00693 7.75 7750 1.097 86 0.86 0.00561 7.75 7750 1.098 69 0.69 0.00459 7.75 7750 1.120
108 1.08 0.00712 8.00 8000 1.132 89 0.89 0.00581 8.00 8000 1.134 72 0.72 0.00479 8.00 8000 1.156
112 1.12 0.00739 8.25 8250 1.168 92 0.92 0.00601 8.20 8200 1.162 75 0.75 0.00499 8.25 8250 1.192
120 1.20 0.00792 8.00 8000 1.132 210 2.10 0.01371 1.00 1000 0.142 80 0.80 0.00533 8.50 8500 1.228
190 1.90 0.01253 7.00 7000 0.991 410 4.10 0.02676 0.50 500 0.071 100 1.00 0.00666 8.60 8600 1.243
500 5.00 0.03264 0.25 250 0.035 320 3.20 0.02130 1.00 1000 0.144
770 7.70 0.05026 0.10 100 0.014 450 4.50 0.02996 0.75 750 0.108
1000 10.00 0.06527 0.05 50 0.007 670 6.70 0.04461 0.50 500 0.072
720 7.20 0.04794 0.30 300 0.043
850 8.50 0.05659 0.25 250 0.036
1050 10.50 0.06991 0.10 100 0.014
 HUBUNGAN TEGANGAN REGANGAN HASIL PENGUJIAN KUAT LENTUR
VARIASI II (PASIR 70% : KARET 30%)

Jenis Benda Uji = Balok 4 Jenis Benda Uji = Balok 5 Jenis Benda Uji = Balok 6
Kode Benda Uji = Variasi 2 (Psr 70% : Karet 30%) Kode Benda Uji = Variasi 2 (Psr 70% : Karet 30%) Kode Benda Uji = Variasi 2 (Psr 70% : Karet 30%)
Panjang (L) = 500 mm Panjang (L) = 500 mm Panjang (L) = 500 mm
Lebar (b) = 153.2 mm Lebar (b) = 152.8 mm Lebar (b) = 152.4 mm
Tinggi (h) = 151.3 mm Tinggi (h) = 150.1 mm Tinggi (h) = 150.1 mm
1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm
Faktor beban = 0.05 KN Faktor beban = 0.05 KN Faktor beban = 0.05 KN
Regangan = Δh / ho Regangan = Δh / ho Regangan = Δh / ho
Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2)

Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan
No No No
Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa)
60 0.6 0.00397 0.25 250 0.036 6 0.1 0.00040 0.25 250 0.036 8 0.1 0.00053 0.25 250 0.036
70 0.7 0.00463 0.50 500 0.071 8 0.1 0.00053 0.50 500 0.073 12 0.1 0.00080 0.50 500 0.073
75 0.8 0.00496 0.75 750 0.107 10 0.1 0.00067 0.75 750 0.109 15 0.2 0.00100 0.75 750 0.109
79 0.8 0.00522 1.00 1000 0.143 12 0.1 0.00080 1.00 1000 0.145 19 0.2 0.00127 1.00 1000 0.146
83 0.8 0.00549 1.25 1250 0.178 13 0.1 0.00087 1.25 1250 0.182 21.5 0.2 0.00143 1.25 1250 0.182
87 0.9 0.00575 1.50 1500 0.214 15 0.2 0.00100 1.50 1500 0.218 24 0.2 0.00160 1.50 1500 0.218
91 0.9 0.00601 1.75 1750 0.250 18 0.2 0.00120 1.75 1750 0.254 27 0.3 0.00180 1.75 1750 0.255
96 1.0 0.00635 2.00 2000 0.285 21 0.2 0.00140 2.00 2000 0.290 30 0.3 0.00200 2.00 2000 0.291
98 1.0 0.00648 2.25 2250 0.321 24 0.2 0.00160 2.25 2250 0.327 34 0.3 0.00227 2.25 2250 0.328
105 1.1 0.00694 2.50 2500 0.356 27 0.3 0.00180 2.50 2500 0.363 36 0.4 0.00240 2.50 2500 0.364
107 1.1 0.00707 2.75 2750 0.392 30 0.3 0.00200 2.75 2750 0.399 39 0.4 0.00260 2.75 2750 0.400
111 1.1 0.00734 3.00 3000 0.428 34 0.3 0.00227 3.00 3000 0.436 42 0.4 0.00280 3.00 3000 0.437
114 1.1 0.00753 3.25 3250 0.463 36 0.4 0.00240 3.25 3250 0.472 45 0.5 0.00300 3.25 3250 0.473
118 1.2 0.00780 3.50 3500 0.499 40 0.4 0.00266 3.50 3500 0.508 49 0.5 0.00326 3.50 3500 0.510
122 1.2 0.00806 3.75 3750 0.535 43 0.4 0.00286 3.75 3750 0.545 52 0.5 0.00346 3.75 3750 0.546
125 1.3 0.00826 4.00 4000 0.570 47 0.5 0.00313 4.00 4000 0.581 54.5 0.5 0.00363 4.00 4000 0.582
127.5 1.3 0.00843 4.25 4250 0.606 49 0.5 0.00326 4.25 4250 0.617 57 0.6 0.00380 4.25 4250 0.619
131 1.3 0.00866 4.50 4500 0.642 52 0.5 0.00346 4.50 4500 0.654 60 0.6 0.00400 4.50 4500 0.655
132.5 1.3 0.00876 4.75 4750 0.677 55 0.6 0.00366 4.75 4750 0.690 63 0.6 0.00420 4.75 4750 0.692
135 1.4 0.00892 5.00 5000 0.713 58 0.6 0.00386 5.00 5000 0.726 65 0.7 0.00433 5.00 5000 0.728
137 1.4 0.00905 5.25 5250 0.749 60 0.6 0.00400 5.25 5250 0.763 67 0.7 0.00446 5.25 5250 0.765
139 1.4 0.00919 5.50 5500 0.784 62 0.6 0.00413 5.50 5500 0.799 68 0.7 0.00453 5.50 5500 0.801
142 1.4 0.00939 5.75 5750 0.820 64 0.6 0.00426 5.75 5750 0.835 70 0.7 0.00466 5.75 5750 0.837
144 1.4 0.00952 6.00 6000 0.855 66 0.7 0.00440 6.00 6000 0.871 71 0.7 0.00473 6.00 6000 0.874
146 1.5 0.00965 6.25 6250 0.891 67 0.7 0.00446 6.25 6250 0.908 73 0.7 0.00486 6.25 6250 0.910
148 1.5 0.00978 6.50 6500 0.927 70 0.7 0.00466 6.50 6500 0.944 75 0.8 0.00500 6.50 6500 0.947
149 1.5 0.00985 6.75 6750 0.962 71 0.7 0.00473 6.75 6750 0.980 76.5 0.8 0.00510 6.75 6750 0.983
151 1.5 0.00998 7.00 7000 0.998 73 0.7 0.00486 7.00 7000 1.017 78 0.8 0.00520 7.00 7000 1.019
153 1.5 0.01011 7.25 7250 1.034 75 0.8 0.00500 7.25 7250 1.053 80 0.8 0.00533 7.25 7250 1.056
154 1.5 0.01018 7.50 7500 1.069 76 0.8 0.00506 7.50 7500 1.089 81 0.8 0.00540 7.50 7500 1.092
156 1.6 0.01031 7.75 7750 1.105 78 0.8 0.00520 7.75 7750 1.126 83 0.8 0.00553 7.75 7750 1.129
157 1.6 0.01038 8.00 8000 1.141 79.5 0.8 0.00530 8.00 8000 1.162 84 0.8 0.00560 8.00 8000 1.165
159 1.6 0.01051 8.25 8250 1.176 81 0.8 0.00540 8.25 8250 1.198 86 0.9 0.00573 8.25 8250 1.201
160.5 1.6 0.01061 8.50 8500 1.212 82 0.8 0.00546 8.50 8500 1.235 87 0.9 0.00580 8.50 8500 1.238
162 1.6 0.01071 8.75 8750 1.248 84 0.8 0.00560 8.75 8750 1.271 88 0.9 0.00586 8.75 8750 1.274
163 1.6 0.01077 9.00 9000 1.283 85 0.9 0.00566 9.00 9000 1.307 89 0.9 0.00593 9.00 9000 1.311
165 1.7 0.01091 9.25 9250 1.319 87 0.9 0.00580 9.25 9250 1.343 91 0.9 0.00606 9.25 9250 1.347
166 1.7 0.01097 9.50 9500 1.354 88.5 0.9 0.00590 9.50 9500 1.380 92 0.9 0.00613 9.50 9500 1.383
168 1.7 0.01110 9.75 9750 1.390 90 0.9 0.00600 9.75 9750 1.416 94 0.9 0.00626 9.75 9750 1.420
169 1.7 0.01117 10.00 10000 1.426 91 0.9 0.00606 10.00 10000 1.452 95 1.0 0.00633 10.00 10000 1.456
170 1.7 0.01124 10.25 10250 1.461 92 0.9 0.00613 10.25 10250 1.489 97 1.0 0.00646 10.30 10300 1.500
171.5 1.7 0.01134 10.50 10500 1.497 94 0.9 0.00626 10.50 10500 1.525 100 1.0 0.00666 9.50 9500 1.383
173 1.7 0.01143 10.75 10750 1.533 95 1.0 0.00633 10.75 10750 1.561 240 2.4 0.01599 1.00 1000 0.146
175 1.8 0.01157 11.00 11000 1.568 97 1.0 0.00646 11.00 11000 1.598 650 6.5 0.04330 0.50 500 0.073
290 2.9 0.01917 11.25 11250 1.604 99 1.0 0.00660 11.25 11250 1.634 700 7.0 0.04664 0.25 250 0.036
740 7.4 0.04891 0.50 500 0.071 100 1.0 0.00666 11.50 11500 1.670
1170 11.7 0.07733 0.25 250 0.036 102 1.0 0.00680 11.75 11750 1.707
104 1.0 0.00693 12.00 12000 1.743
115 1.2 0.00766 11.50 11500 1.670
300 3.0 0.01999 0.50 500 0.073
320 3.2 0.02132 0.25 250 0.036
 HUBUNGAN TEGANGAN REGANGAN HASIL PENGUJIAN KUAT LENTUR
VARIASI III (PASIR 80% : KARET 20%)
Jenis Benda Uji = Balok 7 Jenis Benda Uji = Balok 8 Jenis Benda Uji = Balok 9
Kode Benda Uji = Variasi 3 (Psr 80% : Karet 20%) Kode Benda Uji = Variasi 3 (Psr 80% : Karet 20%) Kode Benda Uji = Variasi 3 (Psr 80% : Karet 20%)
Panjang (L) = 500 mm Panjang (L) = 500 mm Panjang (L) = 500 mm
Lebar (b) = 150.8 mm Lebar (b) = 150.0 mm Lebar (b) = 150.0 mm
Tinggi (h) = 150.3 mm Tinggi (h) = 149.9 mm Tinggi (h) = 151.1 mm
1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm
Faktor beban = 0.05 KN Faktor beban = 0.05 KN Faktor beban = 0.05 KN
Regangan = Δh / ho Regangan = Δh / ho Regangan = Δh / ho
Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2)
Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan
No No No
Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa)
26 0.3 0.00173 0.25 250 0.037 8 0.1 0.00053 0.25 250 0.037 6 0.1 0.00040 0.25 250 0.036
29 0.3 0.00193 0.50 500 0.073 11 0.1 0.00073 0.50 500 0.074 8 0.1 0.00053 0.50 500 0.073
31 0.3 0.00206 0.75 750 0.110 14 0.1 0.00093 0.75 750 0.111 10 0.1 0.00066 0.75 750 0.109
33 0.3 0.00220 1.00 1000 0.147 17 0.2 0.00113 1.00 1000 0.148 12 0.1 0.00079 1.00 1000 0.146
36 0.4 0.00240 1.25 1250 0.183 19 0.2 0.00127 1.25 1250 0.185 14 0.1 0.00093 1.25 1250 0.182
38 0.4 0.00253 1.50 1500 0.220 22 0.2 0.00147 1.50 1500 0.223 16 0.2 0.00106 1.50 1500 0.219
40 0.4 0.00266 1.75 1750 0.257 24 0.2 0.00160 1.75 1750 0.260 18 0.2 0.00119 1.75 1750 0.255
42 0.4 0.00279 2.00 2000 0.294 27 0.3 0.00180 2.00 2000 0.297 20 0.2 0.00132 2.00 2000 0.292
43 0.4 0.00286 2.25 2250 0.330 29 0.3 0.00193 2.25 2250 0.334 24 0.2 0.00159 2.25 2250 0.328
45 0.5 0.00299 2.50 2500 0.367 31 0.3 0.00207 2.50 2500 0.371 24.5 0.2 0.00162 2.50 2500 0.365
48 0.5 0.00319 2.75 2750 0.404 32.5 0.3 0.00217 2.75 2750 0.408 25 0.3 0.00165 2.75 2750 0.401
51 0.5 0.00339 3.00 3000 0.440 35 0.4 0.00233 3.00 3000 0.445 29 0.3 0.00192 3.00 3000 0.438
53 0.5 0.00353 3.25 3250 0.477 38 0.4 0.00254 3.25 3250 0.482 33 0.3 0.00218 3.25 3250 0.474
57 0.6 0.00379 3.50 3500 0.514 39 0.4 0.00260 3.50 3500 0.519 38 0.4 0.00251 3.50 3500 0.511
59 0.6 0.00393 3.75 3750 0.550 41 0.4 0.00274 3.75 3750 0.556 41 0.4 0.00271 3.75 3750 0.547
62 0.6 0.00413 4.00 4000 0.587 43 0.4 0.00287 4.00 4000 0.593 45 0.5 0.00298 4.00 4000 0.584
64 0.6 0.00426 4.25 4250 0.624 48 0.5 0.00320 4.25 4250 0.630 48 0.5 0.00318 4.25 4250 0.620
67 0.7 0.00446 4.50 4500 0.660 50 0.5 0.00334 4.50 4500 0.668 51 0.5 0.00338 4.50 4500 0.657
69 0.7 0.00459 4.75 4750 0.697 52 0.5 0.00347 4.75 4750 0.705 55 0.6 0.00364 4.75 4750 0.693
72 0.7 0.00479 5.00 5000 0.734 54.5 0.5 0.00364 5.00 5000 0.742 59 0.6 0.00390 5.00 5000 0.730
73 0.7 0.00486 5.25 5250 0.771 57 0.6 0.00380 5.25 5250 0.779 63 0.6 0.00417 5.25 5250 0.766
75 0.8 0.00499 5.50 5500 0.807 58 0.6 0.00387 5.50 5500 0.816 65 0.7 0.00430 5.50 5500 0.803
77 0.8 0.00512 5.75 5750 0.844 59 0.6 0.00394 5.75 5750 0.853 66 0.7 0.00437 5.75 5750 0.839
79 0.8 0.00526 6.00 6000 0.881 61 0.6 0.00407 6.00 6000 0.890 68 0.7 0.00450 6.00 6000 0.876
80 0.8 0.00532 6.25 6250 0.917 62 0.6 0.00414 6.25 6250 0.927 70 0.7 0.00463 6.25 6250 0.912
81 0.8 0.00539 6.50 6500 0.954 63 0.6 0.00420 6.50 6500 0.964 71 0.7 0.00470 6.50 6500 0.949
82 0.8 0.00546 6.75 6750 0.991 64.5 0.6 0.00430 6.75 6750 1.001 73 0.7 0.00483 6.75 6750 0.985
83 0.8 0.00552 7.00 7000 1.027 65 0.7 0.00434 7.00 7000 1.038 74 0.7 0.00490 7.00 7000 1.022
84.5 0.8 0.00562 7.25 7250 1.064 67 0.7 0.00447 7.25 7250 1.076 76 0.8 0.00503 7.25 7250 1.058
85 0.9 0.00566 7.50 7500 1.101 68 0.7 0.00454 7.50 7500 1.113 77 0.8 0.00510 7.50 7500 1.095
86 0.9 0.00572 7.75 7750 1.138 69 0.7 0.00460 7.75 7750 1.150 79 0.8 0.00523 7.75 7750 1.131
87 0.9 0.00579 8.00 8000 1.174 70 0.7 0.00467 8.00 8000 1.187 81 0.8 0.00536 8.00 8000 1.168
88 0.9 0.00585 8.25 8250 1.211 71 0.7 0.00474 8.25 8250 1.224 83 0.8 0.00549 8.25 8250 1.204
89 0.9 0.00592 8.50 8500 1.248 72 0.7 0.00480 8.50 8500 1.261 84 0.8 0.00556 8.50 8500 1.241
90 0.9 0.00599 8.75 8750 1.284 73 0.7 0.00487 8.75 8750 1.298 85 0.9 0.00563 8.75 8750 1.277
90.5 0.9 0.00602 9.00 9000 1.321 74 0.7 0.00494 9.00 9000 1.335 86 0.9 0.00569 9.00 9000 1.314
91.0 0.9 0.00605 9.25 9250 1.358 75 0.8 0.00500 9.25 9250 1.372 88 0.9 0.00582 9.25 9250 1.350
92 0.9 0.00612 9.50 9500 1.394 76.5 0.8 0.00510 9.50 9500 1.409 89 0.9 0.00589 9.50 9500 1.387
93 0.9 0.00619 9.75 9750 1.431 78 0.8 0.00520 9.75 9750 1.446 90 0.9 0.00596 9.75 9750 1.423
94 0.9 0.00625 10.00 10000 1.468 79 0.8 0.00527 10.00 10000 1.483 91.5 0.9 0.00606 10.00 10000 1.460
95 1.0 0.00632 10.25 10250 1.504 80.5 0.8 0.00537 10.25 10250 1.521 93 0.9 0.00615 10.25 10250 1.496
96 1.0 0.00639 10.50 10500 1.541 81 0.8 0.00540 10.50 10500 1.558 94 0.9 0.00622 10.50 10500 1.533
96.5 1.0 0.00642 10.75 10750 1.578 100 1.0 0.00667 10.75 10750 1.595 95 1.0 0.00629 10.75 10750 1.569
97.5 1.0 0.00649 11.00 11000 1.615 147 1.5 0.00981 11.00 11000 1.632 96 1.0 0.00635 11.00 11000 1.606
98 1.0 0.00652 11.25 11250 1.651 149 1.5 0.00994 11.25 11250 1.669 97 1.0 0.00642 11.25 11250 1.642
99 1.0 0.00659 11.50 11500 1.688 151 1.5 0.01007 11.50 11500 1.706 98 1.0 0.00649 11.50 11500 1.679
100 1.0 0.00665 11.75 11750 1.725 152 1.5 0.01014 11.75 11750 1.743 99 1.0 0.00655 11.75 11750 1.715
101 1.0 0.00672 12.00 12000 1.761 155 1.6 0.01034 12.00 12000 1.780 100 1.0 0.00662 12.00 12000 1.752
102 1.0 0.00679 12.25 12250 1.798 157.5 1.6 0.01051 12.25 12250 1.817 101 1.0 0.00668 12.25 12250 1.788
104 1.0 0.00692 12.50 12500 1.835 200 2.0 0.01334 12.30 12300 1.825 102 1.0 0.00675 12.50 12500 1.825
200 2.0 0.01331 0.50 500 0.073 300 3.0 0.02001 0.50 500 0.074 103 1.0 0.00682 12.75 12750 1.861
360 3.6 0.02395 0.25 250 0.037 340 3.4 0.02268 0.25 250 0.037 104 1.0 0.00688 13.00 13000 1.898
105 1.1 0.00695 13.25 13250 1.934
200 2.0 0.01324 13.35 13350 1.949
 HUBUNGAN TEGANGAN REGANGAN HASIL PENGUJIAN KUAT LENTUR
VARIASI IV (PASIR 90% : KARET 10%)

Jenis Benda Uji = Balok 10 Jenis Benda Uji = Balok 11 Jenis Benda Uji = Balok 12
Kode Benda Uji = Variasi 4 (Psr 90% : Karet 10%) Kode Benda Uji = Variasi 4 (Psr 90% : Karet 10%) Kode Benda Uji = Variasi 4 (Psr 90% : Karet 10%)
Panjang (L) = 500 mm Panjang (L) = 500 mm Panjang (L) = 500 mm
Lebar (b) = 149.4 mm Lebar (b) = 150.1 mm Lebar (b) = 150.4 mm
Tinggi (h) = 151.1 mm Tinggi (h) = 151.7 mm Tinggi (h) = 152.0 mm
1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm
Faktor beban = 0.05 KN Faktor beban = 0.05 KN Faktor beban = 0.05 KN
Regangan = Δh / ho Regangan = Δh / ho Regangan = Δh / ho
Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2)

Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan
No No No
Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa)
4 0.0 0.00026 0.25 250 0.037 9 0.1 0.00059 0.25 250 0.036 4 0.0 0.00026 0.25 250 0.036
7 0.1 0.00046 0.50 500 0.073 15 0.2 0.00099 0.50 500 0.072 8 0.1 0.00053 0.50 500 0.072
11 0.1 0.00073 0.75 750 0.110 20 0.2 0.00132 0.75 750 0.109 12.5 0.1 0.00082 0.75 750 0.108
17 0.2 0.00113 1.00 1000 0.147 26 0.3 0.00171 2.00 2000 0.289 14 0.1 0.00092 1.00 1000 0.144
25 0.3 0.00165 1.25 1250 0.183 32 0.3 0.00211 2.50 2500 0.362 26 0.3 0.00171 1.25 1250 0.180
31 0.3 0.00205 1.50 1500 0.220 41 0.4 0.00270 3.00 3000 0.434 28 0.3 0.00184 3.00 3000 0.432
37 0.4 0.00245 1.75 1750 0.257 48 0.5 0.00316 3.50 3500 0.507 29 0.3 0.00191 3.50 3500 0.504
44 0.4 0.00291 4.00 4000 0.586 54 0.5 0.00356 4.00 4000 0.579 31 0.3 0.00204 4.00 4000 0.576
47 0.5 0.00311 4.50 4500 0.660 59 0.6 0.00389 4.50 4500 0.651 33 0.3 0.00217 4.50 4500 0.648
52 0.5 0.00344 5.00 5000 0.733 62 0.6 0.00409 5.00 5000 0.724 40 0.4 0.00263 5.00 5000 0.719
54 0.5 0.00357 5.50 5500 0.806 64 0.6 0.00422 5.50 5500 0.796 41 0.4 0.00270 5.50 5500 0.791
58 0.6 0.00384 6.00 6000 0.880 67 0.7 0.00442 6.00 6000 0.868 42 0.4 0.00276 6.00 6000 0.863
60 0.6 0.00397 6.50 6500 0.953 70 0.7 0.00461 6.50 6500 0.941 42.5 0.4 0.00280 6.50 6500 0.935
63 0.6 0.00417 7.00 7000 1.026 72 0.7 0.00475 7.00 7000 1.013 45 0.5 0.00296 7.00 7000 1.007
65 0.7 0.00430 7.50 7500 1.099 74 0.7 0.00488 7.50 7500 1.086 47 0.5 0.00309 7.50 7500 1.079
67 0.7 0.00443 8.00 8000 1.173 77 0.8 0.00508 8.00 8000 1.158 44 0.4 0.00289 8.00 8000 1.151
69 0.7 0.00457 8.50 8500 1.246 78 0.8 0.00514 8.50 8500 1.230 51 0.5 0.00336 8.50 8500 1.223
70 0.7 0.00463 9.00 9000 1.319 80 0.8 0.00527 9.00 9000 1.303 52.5 0.5 0.00345 9.00 9000 1.295
72 0.7 0.00477 9.50 9500 1.393 82.5 0.8 0.00544 9.50 9500 1.375 54 0.5 0.00355 9.50 9500 1.367
73 0.7 0.00483 10.00 10000 1.466 84 0.8 0.00554 10.00 10000 1.447 56 0.6 0.00368 10.00 10000 1.439
74 0.7 0.00490 10.50 10500 1.539 86 0.9 0.00567 10.50 10500 1.520 57 0.6 0.00375 10.50 10500 1.511
76 0.8 0.00503 11.00 11000 1.612 88 0.9 0.00580 11.00 11000 1.592 59 0.6 0.00388 11.00 11000 1.583
77 0.8 0.00510 11.50 11500 1.686 89 0.9 0.00587 11.50 11500 1.665 60 0.6 0.00395 11.50 11500 1.655
78 0.8 0.00516 12.00 12000 1.759 91 0.9 0.00600 12.00 12000 1.737 62 0.6 0.00408 12.00 12000 1.727
80 0.8 0.00529 12.50 12500 1.832 93 0.9 0.00613 12.50 12500 1.809 63 0.6 0.00414 12.50 12500 1.799
81 0.8 0.00536 13.00 13000 1.906 95 1.0 0.00626 13.00 13000 1.882 64 0.6 0.00421 13.00 13000 1.871
83 0.8 0.00549 13.50 13500 1.979 96 1.0 0.00633 13.50 13500 1.954 66 0.7 0.00434 13.50 13500 1.943
85 0.9 0.00563 14.00 14000 2.052 98 1.0 0.00646 14.00 14000 2.026 68 0.7 0.00447 14.00 14000 2.014
86 0.9 0.00569 14.50 14500 2.125 100 1.0 0.00659 14.50 14500 2.099 100 1.0 0.00658 14.20 14200 2.043
87 0.9 0.00576 15.00 15000 2.199 101 1.0 0.00666 15.00 15000 2.171
89 0.9 0.00589 15.50 15500 2.272 102.5 1.0 0.00676 15.50 15500 2.244
90 0.9 0.00596 16.00 16000 2.345 104 1.0 0.00686 16.00 16000 2.316
91 0.9 0.00602 16.50 16500 2.419 105 1.1 0.00692 16.50 16500 2.388
92 0.9 0.00609 17.00 17000 2.492 107 1.1 0.00705 17.00 17000 2.461
100 1.0 0.00662 17.10 17100 2.507 108 1.1 0.00712 17.50 17500 2.533
120 1.2 0.00791 18.00 18000 2.605
 HUBUNGAN TEGANGAN REGANGAN HASIL PENGUJIAN KUAT LENTUR
VARIASI V (PASIR 100% : KARET 0%)

Jenis Benda Uji = Balok 13 Jenis Benda Uji = Balok 14 Jenis Benda Uji = Balok 15
Kode Benda Uji = Variasi 5 (Psr 100% : Karet 0%) Kode Benda Uji = Variasi 5 (Psr 100% : Karet 0%) Kode Benda Uji = Variasi 5 (Psr 100% : Karet 0%)
Panjang (L) = 500 mm Panjang (L) = 500 mm Panjang (L) = 500 mm
Lebar (b) = 152.7 mm Lebar (b) = 151.8 mm Lebar (b) = 151.2 mm
Tinggi (h) = 151.2 mm Tinggi (h) = 148.7 mm Tinggi (h) = 151.4 mm
1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm 1 Strip lendutan = 0.01 mm
Faktor beban = 0.05 KN Faktor beban = 0.05 KN Faktor beban = 0.05 KN
Regangan = Δh / ho Regangan = Δh / ho Regangan = Δh / ho
Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2) Tegangan = (P×L)/(b×h2)

Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan Pembacaan Regangan Beban Beban Tegangan
No No No
Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa) Strip (mm) (KN) (N) (Mpa)
6 0.1 0.00040 0.50 500 0.072 4 0.0 0.00027 0.50 500 0.074 5 0.1 0.00033 0.50 500 0.072
11 0.1 0.00073 1.00 1000 0.143 8 0.1 0.00054 1.00 1000 0.149 9 0.1 0.00059 1.00 1000 0.144
16 0.2 0.00106 1.50 1500 0.215 12 0.1 0.00081 1.50 1500 0.223 13 0.1 0.00086 1.50 1500 0.216
19 0.2 0.00126 2.00 2000 0.286 16 0.2 0.00108 2.00 2000 0.298 17 0.2 0.00112 2.00 2000 0.289
23 0.2 0.00152 2.50 2500 0.358 20 0.2 0.00134 2.50 2500 0.372 22 0.2 0.00145 2.50 2500 0.361
27 0.3 0.00179 3.00 3000 0.430 23 0.2 0.00155 3.00 3000 0.447 26 0.3 0.00172 3.00 3000 0.433
32 0.3 0.00212 3.50 3500 0.501 30 0.3 0.00202 3.50 3500 0.521 31 0.3 0.00205 3.50 3500 0.505
37 0.4 0.00245 4.00 4000 0.573 35 0.4 0.00235 4.00 4000 0.596 36 0.4 0.00238 4.00 4000 0.577
40 0.4 0.00265 4.50 4500 0.645 38 0.4 0.00256 4.50 4500 0.670 40 0.4 0.00264 4.50 4500 0.649
44 0.4 0.00291 5.00 5000 0.716 42 0.4 0.00282 5.00 5000 0.745 44 0.4 0.00291 5.00 5000 0.721
47 0.5 0.00311 5.50 5500 0.788 46 0.5 0.00309 5.50 5500 0.819 48 0.5 0.00317 5.50 5500 0.793
51 0.5 0.00337 6.00 6000 0.859 49 0.5 0.00330 6.00 6000 0.894 52 0.5 0.00343 6.00 6000 0.866
53 0.5 0.00351 6.50 6500 0.931 53 0.5 0.00356 6.50 6500 0.968 54 0.5 0.00357 6.50 6500 0.938
55 0.6 0.00364 7.00 7000 1.003 55 0.6 0.00370 7.00 7000 1.043 57 0.6 0.00376 7.00 7000 1.010
58 0.6 0.00384 7.50 7500 1.074 57 0.6 0.00383 7.50 7500 1.117 59 0.6 0.00390 7.50 7500 1.082
60 0.6 0.00397 8.00 8000 1.146 59 0.6 0.00397 8.00 8000 1.192 61 0.6 0.00403 8.00 8000 1.154
62 0.6 0.00410 8.50 8500 1.217 60 0.6 0.00403 8.50 8500 1.266 63 0.6 0.00416 8.50 8500 1.226
64 0.6 0.00423 9.00 9000 1.289 62 0.6 0.00417 9.00 9000 1.341 65 0.7 0.00429 9.00 9000 1.298
66 0.7 0.00437 9.50 9500 1.361 64 0.6 0.00430 9.50 9500 1.415 67 0.7 0.00443 9.50 9500 1.371
67 0.7 0.00443 10.00 10000 1.432 66 0.7 0.00444 10.00 10000 1.490 69 0.7 0.00456 10.00 10000 1.443
69 0.7 0.00456 10.50 10500 1.504 68 0.7 0.00457 10.50 10500 1.564 71 0.7 0.00469 10.50 10500 1.515
71 0.7 0.00470 11.00 11000 1.576 69.5 0.7 0.00467 11.00 11000 1.639 73 0.7 0.00482 11.00 11000 1.587
73 0.7 0.00483 11.50 11500 1.647 71 0.7 0.00477 11.50 11500 1.713 75 0.8 0.00495 11.50 11500 1.659
74 0.7 0.00489 12.00 12000 1.719 72.5 0.7 0.00488 12.00 12000 1.788 77 0.8 0.00509 12.00 12000 1.731
76 0.8 0.00503 12.50 12500 1.790 74 0.7 0.00498 12.50 12500 1.862 78 0.8 0.00515 12.50 12500 1.803
77 0.8 0.00509 13.00 13000 1.862 76 0.8 0.00511 13.00 13000 1.937 80 0.8 0.00528 13.00 13000 1.875
79 0.8 0.00522 13.50 13500 1.934 77 0.8 0.00518 13.50 13500 2.011 82 0.8 0.00542 13.50 13500 1.948
80 0.8 0.00529 14.00 14000 2.005 79 0.8 0.00531 14.00 14000 2.085 83.5 0.8 0.00552 14.00 14000 2.020
82 0.8 0.00542 14.50 14500 2.077 80 0.8 0.00538 14.50 14500 2.160 85 0.9 0.00561 14.50 14500 2.092
84 0.8 0.00556 15.00 15000 2.148 82 0.8 0.00551 15.00 15000 2.234 87 0.9 0.00575 15.00 15000 2.164
86 0.9 0.00569 15.50 15500 2.220 83 0.8 0.00558 15.50 15500 2.309 88 0.9 0.00581 15.50 15500 2.236
88 0.9 0.00582 16.00 16000 2.292 85 0.9 0.00572 16.00 16000 2.383 90 0.9 0.00594 16.00 16000 2.308
87 0.9 0.00585 16.50 16500 2.458 92 0.9 0.00608 16.50 16500 2.380
88 0.9 0.00592 17.00 17000 2.532 110 1.1 0.00727 16.60 16600 2.395
100 1.0 0.00672 17.30 17300 2.577
 Lampiran 4-13

HASIL PENGUJIAN KUAT LENTUR BALOK BETON KARET (UMUR 28 HARI)

Nomor : Diterima Tanggal :

Pengirim : Edward Ngii
Keperluan : Tugas Mata Kuliah S3 " Laboratory Work (3 sks)"

Benda uji (Balok beton / Plat beton / Balok kayu)

Tanggal Panjang Penampang Berat b.j. Tanggal Umur Beban Kuat Kuat Lentur
No Tanda/Kode dibuat Total Lebar Tebal diuji Maks Lentur rata2
(mm) (mm) (mm) (kg) (kg/m3) (hr) (kN) (MPa) (MPa)
1 Var.I (Ps.60%:Krt.40%) 7/29/2013 600 153.70 151.60 24.60 1.760 8/26/2013 28 8.25 1.168
2 Var.I (Ps.60%:Krt.40%) 7/29/2013 603 150.30 153.20 24.40 1.757 8/26/2013 28 8.20 1.162 1.191
3 Var.I (Ps.60%:Krt.40%) 7/29/2013 602 153.40 150.20 24.30 1.752 8/26/2013 28 8.60 1.243
4 Var.II (Ps.70%:Krt.30%) 7/30/2013 603 153.20 151.30 26.40 1.889 8/27/2013 28 11.25 1.604
5 Var.II (Ps.70%:Krt.30%) 7/30/2013 602 152.80 150.10 26.30 1.905 8/27/2013 28 12.00 1.743 1.616
6 Var.II (Ps.70%:Krt.30%) 7/30/2013 603 152.40 150.10 26.20 1.899 8/27/2013 28 10.30 1.500
7 Var.III (Ps.80%:Krt.20%) 7/30/2013 600 150.80 150.30 26.80 1.971 8/27/2013 28 12.50 1.835
8 Var.III (Ps.80%:Krt.20%) 7/30/2013 599 150.00 149.90 26.70 1.982 8/27/2013 28 12.30 1.825 1.869
9 Var.III (Ps.80%:Krt.20%) 7/30/2013 600 150.00 151.10 26.90 1.978 8/27/2013 28 13.35 1.949
10 Var.IV (Ps.90%:Krt.10%) 7/31/2013 600 149.40 151.10 27.70 2.045 8/28/2013 28 17.10 2.507
11 Var.IV (Ps.90%:Krt.10%) 7/31/2013 599 150.10 151.70 28.00 2.053 8/28/2013 28 18.00 2.605 2.385
12 Var.IV (Ps.90%:Krt.10%) 7/31/2013 600 150.40 152.00 28.20 2.056 8/28/2013 28 14.20 2.043
13 Var.V (Ps.100%:Krt.0%) 7/31/2013 602 152.70 151.20 29.20 2.101 8/28/2013 28 16.00 2.292
14 Var.V (Ps.100%:Krt.0%) 7/31/2013 601 151.80 148.70 28.30 2.086 8/28/2013 28 17.30 2.577 2.421
15 Var.V (Ps.100%:Krt.0%) 7/31/2013 602 151.20 151.40 29.10 2.112 8/28/2013 28 16.60 2.395

Jarak tumpuan-tumpuan (L) 500 mm

Jarak tumpuan-beban (1/3 L) 166.667 mm
1/3 1/3 1/3
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN

Jenis Benda Uji = Silinder 1

Kode Benda Uji = Variasi 1 (Psr 60% : Karet 40%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 30 30000 1.699
2 0.0254 0.000100 40 40000 2.265
3 0.0381 0.000150 50 50000 2.831
4 0.0508 0.000200 55 55000 3.114
5 0.0635 0.000250 65 65000 3.680
6 0.0762 0.000300 70 70000 3.963
7 0.0889 0.000350 80 80000 4.529
8 0.1016 0.000400 85 85000 4.812
9 0.1143 0.000450 95 95000 5.379
10 0.1270 0.000500 100 100000 5.662
11 0.1397 0.000550 110 110000 6.228
12 0.1524 0.000600 115 115000 6.511
13 0.1651 0.000650 120 120000 6.794
14 0.1778 0.000700 125 125000 7.077
15 0.1905 0.000750 130 130000 7.360
16 0.2032 0.000800 140 140000 7.926
17 0.2159 0.000850 145 145000 8.209
18 0.2286 0.000900 145 145000 8.209
19 0.2413 0.000950 150 150000 8.493
20 0.2540 0.001000 155 155000 8.776
22 0.2794 0.001100 165 165000 9.342
24 0.3048 0.001200 170 170000 9.625
26 0.3302 0.001300 175 175000 9.908
28 0.3556 0.001400 180 180000 10.191
30 0.3810 0.001500 185 185000 10.474
32 0.4064 0.001600 190 190000 10.757
35 0.4445 0.001750 190 190000 10.757
40 0.5080 0.002000 180 180000 10.191
45 0.5715 0.002250 160 160000 9.059
55 0.6985 0.002750 140 140000 7.926
60 0.7620 0.003000 135 135000 7.643
70 0.8890 0.003500 125 125000 7.077
80 1.0160 0.004000 125 125000 7.077
90 1.1430 0.004500 125 125000 7.077
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 2)

Jenis Benda Uji = Silinder 4

Kode Benda Uji = Variasi 2 (Psr 70% : Karet 30%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 20 20000 1.132
2 0.0254 0.000100 25 25000 1.415
3 0.0381 0.000150 35 35000 1.982
4 0.0508 0.000200 45 45000 2.548
5 0.0635 0.000250 60 60000 3.397
6 0.0762 0.000300 70 70000 3.963
7 0.0889 0.000350 80 80000 4.529
8 0.1016 0.000400 85 85000 4.812
9 0.1143 0.000450 90 90000 5.096
10 0.1270 0.000500 100 100000 5.662
11 0.1397 0.000550 115 115000 6.511
12 0.1524 0.000600 120 120000 6.794
13 0.1651 0.000650 125 125000 7.077
14 0.1778 0.000700 130 130000 7.360
15 0.1905 0.000750 140 140000 7.926
16 0.2032 0.000800 145 145000 8.209
17 0.2159 0.000850 150 150000 8.493
18 0.2286 0.000900 155 155000 8.776
19 0.2413 0.000950 160 160000 9.059
20 0.2540 0.001000 165 165000 9.342
22 0.2794 0.001100 175 175000 9.908
24 0.3048 0.001200 180 180000 10.191
26 0.3302 0.001300 190 190000 10.757
28 0.3556 0.001400 200 200000 11.323
30 0.3810 0.001500 205 205000 11.607
32 0.4064 0.001600 205 205000 11.607
34 0.4318 0.001700 205 205000 11.607
40 0.5080 0.002000 200 200000 11.323
46 0.5842 0.002300 190 190000 10.757
50 0.6350 0.002500 165 165000 9.342
60 0.7620 0.003000 140 140000 7.926
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 3)

Jenis Benda Uji = Silinder 7

Kode Benda Uji = Variasi 3 (Psr 80% : Karet 20%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 30 30000 1.699
2 0.0254 0.000100 50 50000 2.831
3 0.0381 0.000150 60 60000 3.397
4 0.0508 0.000200 75 75000 4.246
5 0.0635 0.000250 80 80000 4.529
6 0.0762 0.000300 95 95000 5.379
7 0.0889 0.000350 105 105000 5.945
8 0.1016 0.000400 110 110000 6.228
9 0.1143 0.000450 120 120000 6.794
10 0.1270 0.000500 135 135000 7.643
11 0.1397 0.000550 150 150000 8.493
12 0.1524 0.000600 160 160000 9.059
13 0.1651 0.000650 165 165000 9.342
14 0.1778 0.000700 170 170000 9.625
15 0.1905 0.000750 180 180000 10.191
16 0.2032 0.000800 185 185000 10.474
17 0.2159 0.000850 195 195000 11.040
18 0.2286 0.000900 200 200000 11.323
19 0.2413 0.000950 205 205000 11.607
20 0.2540 0.001000 210 210000 11.890
22 0.2794 0.001100 220 220000 12.456
24 0.3048 0.001200 230 230000 13.022
26 0.3302 0.001300 245 245000 13.871
28 0.3556 0.001400 260 260000 14.720
30 0.3810 0.001500 270 270000 15.287
32 0.4064 0.001600 270 270000 15.287
34 0.4318 0.001700 275 275000 15.570
36 0.4572 0.001800 280 280000 15.853
38 0.4826 0.001900 295 295000 16.702
40 0.5080 0.002000 295 295000 16.702
45 0.5715 0.002250 290 290000 16.419
50 0.6350 0.002500 275 275000 15.570
60 0.7620 0.003000 250 250000 14.154
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 4)

Jenis Benda Uji = Silinder 10

Kode Benda Uji = Variasi 4 (Psr 90% : Karet 10%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 40 40000 2.265
2 0.0254 0.000100 60 60000 3.397
3 0.0381 0.000150 85 85000 4.812
4 0.0508 0.000200 100 100000 5.662
5 0.0635 0.000250 120 120000 6.794
6 0.0762 0.000300 140 140000 7.926
7 0.0889 0.000350 155 155000 8.776
8 0.1016 0.000400 165 165000 9.342
9 0.1143 0.000450 180 180000 10.191
10 0.1270 0.000500 190 190000 10.757
11 0.1397 0.000550 200 200000 11.323
12 0.1524 0.000600 215 215000 12.173
13 0.1651 0.000650 225 225000 12.739
14 0.1778 0.000700 240 240000 13.588
15 0.1905 0.000750 250 250000 14.154
16 0.2032 0.000800 260 260000 14.720
17 0.2159 0.000850 270 270000 15.287
18 0.2286 0.000900 280 280000 15.853
19 0.2413 0.000950 290 290000 16.419
20 0.2540 0.001000 300 300000 16.985
22 0.2794 0.001100 320 320000 18.117
24 0.3048 0.001200 345 345000 19.533
26 0.3302 0.001300 360 360000 20.382
28 0.3556 0.001400 375 375000 21.231
30 0.3810 0.001500 380 380000 21.515
32 0.4064 0.001600 385 385000 21.798
34 0.4318 0.001700 385 385000 21.798
36 0.4572 0.001800 385 385000 21.798
38 0.4826 0.001900 380 380000 21.515
40 0.5080 0.002000 370 370000 20.948
45 0.5715 0.002250 350 350000 19.816
50 0.6350 0.002500 280 280000 15.853
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 5)

Jenis Benda Uji = Silinder 13

Kode Benda Uji = Variasi 5 (Psr 100% : Karet 0%)
Luas (A) = 17427.79 mm2
Diameter (Ø) = 149 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 40 40000 2.295
2 0.0254 0.000100 60 60000 3.443
3 0.0381 0.000150 80 80000 4.590
4 0.0508 0.000200 95 95000 5.451
5 0.0635 0.000250 110 110000 6.312
6 0.0762 0.000300 125 125000 7.172
7 0.0889 0.000350 140 140000 8.033
8 0.1016 0.000400 155 155000 8.894
9 0.1143 0.000450 165 165000 9.468
10 0.1270 0.000500 175 175000 10.041
11 0.1397 0.000550 190 190000 10.902
12 0.1524 0.000600 200 200000 11.476
13 0.1651 0.000650 210 210000 12.050
14 0.1778 0.000700 220 220000 12.624
15 0.1905 0.000750 225 225000 12.910
16 0.2032 0.000800 235 235000 13.484
17 0.2159 0.000850 245 245000 14.058
18 0.2286 0.000900 255 255000 14.632
19 0.2413 0.000950 265 265000 15.206
20 0.2540 0.001000 275 275000 15.779
22 0.2794 0.001100 290 290000 16.640
24 0.3048 0.001200 305 305000 17.501
26 0.3302 0.001300 320 320000 18.361
28 0.3556 0.001400 335 335000 19.222
30 0.3810 0.001500 350 350000 20.083
32 0.4064 0.001600 360 360000 20.657
34 0.4318 0.001700 365 365000 20.944
36 0.4572 0.001800 375 375000 21.517
38 0.4826 0.001900 385 385000 22.091
40 0.5080 0.002000 395 395000 22.665
45 0.5715 0.002250 405 405000 23.239
50 0.6350 0.002500 415 415000 23.813
55 0.6985 0.002750 415 415000 23.813
60 0.7620 0.003000 410 410000 23.526
65 0.8255 0.003250 395 395000 22.665
70 0.8890 0.003500 380 380000 21.804
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN

Jenis Benda Uji = Silinder 2

Kode Benda Uji = Variasi 1 (Psr 60% : Karet 40%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 15 15000 0.849
2 0.0254 0.000100 35 35000 1.982
3 0.0381 0.000150 45 45000 2.548
4 0.0508 0.000200 50 50000 2.831
5 0.0635 0.000250 60 60000 3.397
6 0.0762 0.000300 70 70000 3.963
7 0.0889 0.000350 75 75000 4.246
8 0.1016 0.000400 80 80000 4.529
9 0.1143 0.000450 90 90000 5.096
10 0.1270 0.000500 95 95000 5.379
11 0.1397 0.000550 100 100000 5.662
12 0.1524 0.000600 105 105000 5.945
13 0.1651 0.000650 115 115000 6.511
14 0.1778 0.000700 120 120000 6.794
15 0.1905 0.000750 125 125000 7.077
16 0.2032 0.000800 130 130000 7.360
17 0.2159 0.000850 135 135000 7.643
18 0.2286 0.000900 140 140000 7.926
19 0.2413 0.000950 145 145000 8.209
20 0.2540 0.001000 150 150000 8.493
22 0.2794 0.001100 155 155000 8.776
24 0.3048 0.001200 160 160000 9.059
26 0.3302 0.001300 165 165000 9.342
28 0.3556 0.001400 170 170000 9.625
30 0.3810 0.001500 170 170000 9.625
32 0.4064 0.001600 170 170000 9.625
35 0.4445 0.001750 170 170000 9.625
40 0.5080 0.002000 165 165000 9.342
45 0.5715 0.002250 150 150000 8.493
50 0.6350 0.002500 150 150000 8.493
60 0.7620 0.003000 135 135000 7.643
70 0.8890 0.003500 125 125000 7.077
80 1.0160 0.004000 115 115000 6.511
90 1.1430 0.004500 110 110000 6.228
100 1.2700 0.005000 100 100000 5.662
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 2)

Jenis Benda Uji = Silinder 5

Kode Benda Uji = Variasi 2 (Psr 70% : Karet 30%)
Luas (A) = 17427.79 mm2
Diameter (Ø) = 149 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 25 25000 1.434
2 0.0254 0.000100 40 40000 2.295
3 0.0381 0.000150 50 50000 2.869
4 0.0508 0.000200 55 55000 3.156
5 0.0635 0.000250 70 70000 4.017
6 0.0762 0.000300 80 80000 4.590
7 0.0889 0.000350 90 90000 5.164
8 0.1016 0.000400 100 100000 5.738
9 0.1143 0.000450 110 110000 6.312
10 0.1270 0.000500 120 120000 6.886
11 0.1397 0.000550 130 130000 7.459
12 0.1524 0.000600 140 140000 8.033
13 0.1651 0.000650 150 150000 8.607
14 0.1778 0.000700 155 155000 8.894
15 0.1905 0.000750 160 160000 9.181
16 0.2032 0.000800 165 165000 9.468
17 0.2159 0.000850 170 170000 9.755
18 0.2286 0.000900 175 175000 10.041
19 0.2413 0.000950 180 180000 10.328
20 0.2540 0.001000 185 185000 10.615
22 0.2794 0.001100 180 180000 10.328
24 0.3048 0.001200 185 185000 10.615
30 0.3810 0.001500 180 180000 10.328
35 0.4445 0.001750 180 180000 10.328
40 0.5080 0.002000 170 170000 9.755
50 0.6350 0.002500 150 150000 8.607
60 0.7620 0.003000 120 120000 6.886
70 0.8890 0.003500 100 100000 5.738
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 3)

Jenis Benda Uji = Silinder 8

Kode Benda Uji = Variasi 3 (Psr 80% : Karet 20%)
Luas (A) = 17898.79 mm2
Diameter (Ø) = 151 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 30 30000 1.676
2 0.0254 0.000100 40 40000 2.235
3 0.0381 0.000150 55 55000 3.073
4 0.0508 0.000200 70 70000 3.911
5 0.0635 0.000250 85 85000 4.749
6 0.0762 0.000300 95 95000 5.308
7 0.0889 0.000350 105 105000 5.866
8 0.1016 0.000400 115 115000 6.425
9 0.1143 0.000450 130 130000 7.263
10 0.1270 0.000500 135 135000 7.542
11 0.1397 0.000550 150 150000 8.380
12 0.1524 0.000600 165 165000 9.219
13 0.1651 0.000650 170 170000 9.498
14 0.1778 0.000700 175 175000 9.777
15 0.1905 0.000750 180 180000 10.057
16 0.2032 0.000800 190 190000 10.615
17 0.2159 0.000850 195 195000 10.895
18 0.2286 0.000900 200 200000 11.174
19 0.2413 0.000950 210 210000 11.733
20 0.2540 0.001000 215 215000 12.012
22 0.2794 0.001100 225 225000 12.571
24 0.3048 0.001200 240 240000 13.409
26 0.3302 0.001300 255 255000 14.247
28 0.3556 0.001400 260 260000 14.526
30 0.3810 0.001500 270 270000 15.085
35 0.4445 0.001750 275 275000 15.364
40 0.5080 0.002000 280 280000 15.644
45 0.5715 0.002250 270 270000 15.085
50 0.6350 0.002500 265 265000 14.805
60 0.7620 0.003000 245 245000 13.688
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 4)

Jenis Benda Uji = Silinder 11

Kode Benda Uji = Variasi 4 (Psr 90% : Karet 10%)
Luas (A) = 17898.79 mm2
Diameter (Ø) = 151 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 40 40000 2.235
2 0.0254 0.000100 60 60000 3.352
3 0.0381 0.000150 80 80000 4.470
4 0.0508 0.000200 100 100000 5.587
5 0.0635 0.000250 115 115000 6.425
6 0.0762 0.000300 130 130000 7.263
7 0.0889 0.000350 145 145000 8.101
8 0.1016 0.000400 160 160000 8.939
9 0.1143 0.000450 170 170000 9.498
10 0.1270 0.000500 180 180000 10.057
11 0.1397 0.000550 195 195000 10.895
12 0.1524 0.000600 205 205000 11.453
13 0.1651 0.000650 215 215000 12.012
14 0.1778 0.000700 225 225000 12.571
15 0.1905 0.000750 235 235000 13.129
16 0.2032 0.000800 245 245000 13.688
17 0.2159 0.000850 250 250000 13.967
18 0.2286 0.000900 255 255000 14.247
19 0.2413 0.000950 265 265000 14.805
20 0.2540 0.001000 275 275000 15.364
22 0.2794 0.001100 290 290000 16.202
24 0.3048 0.001200 305 305000 17.040
26 0.3302 0.001300 320 320000 17.878
28 0.3556 0.001400 335 335000 18.716
30 0.3810 0.001500 350 350000 19.554
32 0.4064 0.001600 360 360000 20.113
34 0.4318 0.001700 365 365000 20.392
36 0.4572 0.001800 375 375000 20.951
38 0.4826 0.001900 380 380000 21.230
40 0.5080 0.002000 385 385000 21.510
45 0.5715 0.002250 385 385000 21.510
50 0.6350 0.002500 375 375000 20.951
55 0.6985 0.002750 355 355000 19.834
60 0.7620 0.003000 320 320000 17.878
65 0.8255 0.003250 250 250000 13.967
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 5)

Jenis Benda Uji = Silinder 14

Kode Benda Uji = Variasi 5 (Psr 100% : Karet 0%)
Luas (A) = 17427.79 mm2
Diameter (Ø) = 149 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 50 50000 2.869
2 0.0254 0.000100 70 70000 4.017
3 0.0381 0.000150 95 95000 5.451
4 0.0508 0.000200 110 110000 6.312
5 0.0635 0.000250 130 130000 7.459
6 0.0762 0.000300 145 145000 8.320
7 0.0889 0.000350 160 160000 9.181
8 0.1016 0.000400 170 170000 9.755
9 0.1143 0.000450 185 185000 10.615
10 0.1270 0.000500 195 195000 11.189
11 0.1397 0.000550 205 205000 11.763
12 0.1524 0.000600 215 215000 12.337
13 0.1651 0.000650 225 225000 12.910
14 0.1778 0.000700 235 235000 13.484
15 0.1905 0.000750 245 245000 14.058
16 0.2032 0.000800 255 255000 14.632
17 0.2159 0.000850 265 265000 15.206
18 0.2286 0.000900 275 275000 15.779
19 0.2413 0.000950 285 285000 16.353
20 0.2540 0.001000 295 295000 16.927
22 0.2794 0.001100 315 315000 18.075
24 0.3048 0.001200 335 335000 19.222
26 0.3302 0.001300 350 350000 20.083
28 0.3556 0.001400 365 365000 20.944
30 0.3810 0.001500 375 375000 21.517
32 0.4064 0.001600 385 385000 22.091
34 0.4318 0.001700 395 395000 22.665
36 0.4572 0.001800 400 400000 22.952
38 0.4826 0.001900 400 400000 22.952
40 0.5080 0.002000 405 405000 23.239
45 0.5715 0.002250 405 405000 23.239
50 0.6350 0.002500 395 395000 22.665
55 0.6985 0.002750 350 350000 20.083
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN

Jenis Benda Uji = Silinder 3

Kode Benda Uji = Variasi 1 (Psr 60% : Karet 40%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 25 25000 1.415
2 0.0254 0.000100 35 35000 1.982
3 0.0381 0.000150 45 45000 2.548
4 0.0508 0.000200 55 55000 3.114
5 0.0635 0.000250 65 65000 3.680
6 0.0762 0.000300 70 70000 3.963
7 0.0889 0.000350 80 80000 4.529
8 0.1016 0.000400 85 85000 4.812
9 0.1143 0.000450 95 95000 5.379
10 0.1270 0.000500 100 100000 5.662
11 0.1397 0.000550 105 105000 5.945
12 0.1524 0.000600 115 115000 6.511
13 0.1651 0.000650 120 120000 6.794
14 0.1778 0.000700 125 125000 7.077
15 0.1905 0.000750 130 130000 7.360
16 0.2032 0.000800 140 140000 7.926
17 0.2159 0.000850 145 145000 8.209
18 0.2286 0.000900 150 150000 8.493
19 0.2413 0.000950 155 155000 8.776
20 0.2540 0.001000 155 155000 8.776
22 0.2794 0.001100 165 165000 9.342
24 0.3048 0.001200 170 170000 9.625
26 0.3302 0.001300 175 175000 9.908
28 0.3556 0.001400 175 175000 9.908
30 0.3810 0.001500 175 175000 9.908
35 0.4445 0.001750 170 170000 9.625
40 0.5080 0.002000 160 160000 9.059
45 0.5715 0.002250 150 150000 8.493
50 0.6350 0.002500 140 140000 7.926
55 0.6985 0.002750 115 115000 6.511
60 0.7620 0.003000 90 90000 5.096
65 0.8255 0.003250 85 85000 4.812
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 2)

Jenis Benda Uji = Silinder 6

Kode Benda Uji = Variasi 2 (Psr 70% : Karet 30%)
Luas (A) = 17427.79 mm2
Diameter (Ø) = 149 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 30 30000 1.721
2 0.0254 0.000100 45 45000 2.582
3 0.0381 0.000150 55 55000 3.156
4 0.0508 0.000200 60 60000 3.443
5 0.0635 0.000250 70 70000 4.017
6 0.0762 0.000300 80 80000 4.590
7 0.0889 0.000350 90 90000 5.164
8 0.1016 0.000400 95 95000 5.451
9 0.1143 0.000450 100 100000 5.738
10 0.1270 0.000500 105 105000 6.025
11 0.1397 0.000550 115 115000 6.599
12 0.1524 0.000600 125 125000 7.172
13 0.1651 0.000650 130 130000 7.459
14 0.1778 0.000700 140 140000 8.033
15 0.1905 0.000750 150 150000 8.607
16 0.2032 0.000800 155 155000 8.894
17 0.2159 0.000850 160 160000 9.181
18 0.2286 0.000900 165 165000 9.468
19 0.2413 0.000950 170 170000 9.755
20 0.2540 0.001000 175 175000 10.041
22 0.2794 0.001100 180 180000 10.328
24 0.3048 0.001200 185 185000 10.615
26 0.3302 0.001300 190 190000 10.902
30 0.3810 0.001500 190 190000 10.902
35 0.4445 0.001750 190 190000 10.902
40 0.5080 0.002000 180 180000 10.328
50 0.6350 0.002500 165 165000 9.468
60 0.7620 0.003000 150 150000 8.607
70 0.8890 0.003500 140 140000 8.033
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 3)

Jenis Benda Uji = Silinder 9

Kode Benda Uji = Variasi 3 (Psr 80% : Karet 20%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 25 25000 1.415
2 0.0254 0.000100 40 40000 2.265
3 0.0381 0.000150 50 50000 2.831
4 0.0508 0.000200 65 65000 3.680
5 0.0635 0.000250 80 80000 4.529
6 0.0762 0.000300 90 90000 5.096
7 0.0889 0.000350 100 100000 5.662
8 0.1016 0.000400 110 110000 6.228
9 0.1143 0.000450 120 120000 6.794
10 0.1270 0.000500 130 130000 7.360
11 0.1397 0.000550 140 140000 7.926
12 0.1524 0.000600 150 150000 8.493
13 0.1651 0.000650 160 160000 9.059
14 0.1778 0.000700 170 170000 9.625
15 0.1905 0.000750 180 180000 10.191
16 0.2032 0.000800 185 185000 10.474
17 0.2159 0.000850 195 195000 11.040
18 0.2286 0.000900 200 200000 11.323
19 0.2413 0.000950 210 210000 11.890
20 0.2540 0.001000 215 215000 12.173
22 0.2794 0.001100 230 230000 13.022
24 0.3048 0.001200 245 245000 13.871
26 0.3302 0.001300 255 255000 14.437
28 0.3556 0.001400 265 265000 15.004
30 0.3810 0.001500 270 270000 15.287
32 0.4064 0.001600 280 280000 15.853
34 0.4318 0.001700 290 290000 16.419
36 0.4572 0.001800 295 295000 16.702
38 0.4826 0.001900 300 300000 16.985
40 0.5080 0.002000 305 305000 17.268
45 0.5715 0.002250 300 300000 16.985
50 0.6350 0.002500 280 280000 15.853
55 0.6985 0.002750 265 265000 15.004
60 0.7620 0.003000 240 240000 13.588
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 4)

Jenis Benda Uji = Silinder 12

Kode Benda Uji = Variasi 4 (Psr 90% : Karet 10%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 35 35000 1.982
2 0.0254 0.000100 50 50000 2.831
3 0.0381 0.000150 65 65000 3.680
4 0.0508 0.000200 80 80000 4.529
5 0.0635 0.000250 95 95000 5.379
6 0.0762 0.000300 110 110000 6.228
7 0.0889 0.000350 125 125000 7.077
8 0.1016 0.000400 140 140000 7.926
9 0.1143 0.000450 150 150000 8.493
10 0.1270 0.000500 165 165000 9.342
11 0.1397 0.000550 175 175000 9.908
12 0.1524 0.000600 185 185000 10.474
13 0.1651 0.000650 195 195000 11.040
14 0.1778 0.000700 200 200000 11.323
15 0.1905 0.000750 210 210000 11.890
16 0.2032 0.000800 220 220000 12.456
17 0.2159 0.000850 230 230000 13.022
18 0.2286 0.000900 240 240000 13.588
19 0.2413 0.000950 250 250000 14.154
20 0.2540 0.001000 255 255000 14.437
22 0.2794 0.001100 270 270000 15.287
24 0.3048 0.001200 285 285000 16.136
26 0.3302 0.001300 300 300000 16.985
28 0.3556 0.001400 315 315000 17.834
30 0.3810 0.001500 325 325000 18.401
32 0.4064 0.001600 340 340000 19.250
34 0.4318 0.001700 345 345000 19.533
36 0.4572 0.001800 355 355000 20.099
38 0.4826 0.001900 360 360000 20.382
40 0.5080 0.002000 365 365000 20.665
45 0.5715 0.002250 375 375000 21.231
50 0.6350 0.002500 375 375000 21.231
55 0.6985 0.002750 360 360000 20.382
60 0.7620 0.003000 330 330000 18.684
65 0.8255 0.003250 305 305000 17.268
 HUBUNGAN TEGANGAN REGANGAN HASIL
PENGUJIAN KUAT TEKAN (VARIASI 5)

Jenis Benda Uji = Silinder 15

Kode Benda Uji = Variasi 5 (Psr 100% : Karet 0%)
Luas (A) = 17662.50 mm2
Diameter (Ø) = 150 mm
Tinggi (Lo) = 254 mm
1 Strip dial = 0.0127 mm
Regangan = ΔL / Lo
Tegangan = Beban / Luas

Regangan Beban Beban Tegangan

No
Strip (mm) (KN) (N) (Mpa)
1 0.0127 0.000050 45 45000 2.548
2 0.0254 0.000100 60 60000 3.397
3 0.0381 0.000150 75 75000 4.246
4 0.0508 0.000200 95 95000 5.379
5 0.0635 0.000250 110 110000 6.228
6 0.0762 0.000300 125 125000 7.077
7 0.0889 0.000350 140 140000 7.926
8 0.1016 0.000400 155 155000 8.776
9 0.1143 0.000450 170 170000 9.625
10 0.1270 0.000500 180 180000 10.191
11 0.1397 0.000550 190 190000 10.757
12 0.1524 0.000600 200 200000 11.323
13 0.1651 0.000650 210 210000 11.890
14 0.1778 0.000700 225 225000 12.739
15 0.1905 0.000750 235 235000 13.305
16 0.2032 0.000800 245 245000 13.871
17 0.2159 0.000850 255 255000 14.437
18 0.2286 0.000900 265 265000 15.004
19 0.2413 0.000950 275 275000 15.570
20 0.2540 0.001000 285 285000 16.136
22 0.2794 0.001100 305 305000 17.268
24 0.3048 0.001200 320 320000 18.117
26 0.3302 0.001300 335 335000 18.967
28 0.3556 0.001400 350 350000 19.816
30 0.3810 0.001500 360 360000 20.382
32 0.4064 0.001600 375 375000 21.231
34 0.4318 0.001700 385 385000 21.798
36 0.4572 0.001800 395 395000 22.364
38 0.4826 0.001900 400 400000 22.647
40 0.5080 0.002000 405 405000 22.930
45 0.5715 0.002250 405 405000 22.930
50 0.6350 0.002500 405 405000 22.930
55 0.6985 0.002750 405 405000 22.930
60 0.7620 0.003000 400 400000 22.647
65 0.8255 0.003250 395 395000 22.364
70 0.8890 0.003500 385 385000 21.798
75 0.9525 0.003750 375 375000 21.231
80 1.0160 0.004000 360 360000 20.382
 14

Tegangan (MPa)
12

10

8 Teg. maks (f'c) = 10.7573 MPa

Tegangan 0,5f'c = 4.30290 MPa
6 Tegangan 0,5f'c
Silinder 1 = 0.00034
4

2 x y
0 4.303
0 0.00034 4.303
0.0000 0.0010 0.0020 0.0030 0.0040 0.0050 0.00034 0
Regangan (mm)

14

12

10
Teg. maks (f'c) = 9.62491 MPa
Tegangan (MPa)

8 Tegangan 0,5f'c = 3.84996 MPa

6
Tegangan 0,5f'c = 0.00030

4 silinder 2
x y
2 0 3.850
0.0003 3.850
0 0.00030 0
0.0000 0.0010 0.0020 0.0030 0.0040 0.0050 0.0060
Regangan (mm)

14
Tegangan (MPa)

12

10

8 Teg. maks (f'c) = 9.90800 MPa

Tegangan 0,5f'c = 3.96320 MPa
6 Tegangan 0,5f'c = 0.00030

4
silinder 3
x y
2
0 3.963
0.0003 3.963
0
0.0000 0.0010 0.0020 0.0030 0.0040
0.00030 0

Regangan (mm)
 14

Tegangan (MPa)
12

10
Teg. maks (f'c) = 11.6065 MPa
8
Tegangan 0,5f'c = 4.64260 MPa
6 Tegangan 0,5f'c = 0.00038
Silinder 4
4
x y
2
0 4.643
0 0.00038 4.643
0.0000 0.0010 0.0020 0.0030 0.0040 0.00038 0
Regangan (mm)

14

12

10
Tegangan (MPa)

8 Teg. maks (f'c) = 10.6152 MPa

Tegangan 0,5f'c = 4.24609 MPa
6 Tegangan 0,5f'c = 0.00027
4 Silinder 5

2 x y
0 4.246
0 0.00027 4.246
0.0000 0.0010 0.0020 0.0030 0.0040 0.00027 0
Regangan (mm)

14
Tegangan (MPa)

12

10
Teg. maks (f'c) = 10.9021 MPa
8 Tegangan 0,5f'c = 4.36085 MPa
Tegangan 0,5f'c = 0.00029
6

4
Silinder 6 x y
2 0 4.361
0.00029 4.361
0 0.00029 0
0.0000 0.0010 0.0020 0.0030 0.0040
Regangan (mm)
 18

Tegangan (MPa)
16
14
12
Teg. maks (f'c) = 16.7021 MPa
10 Tegangan 0,5f'c = 6.68082 MPa
8 Tegangan 0,5f'c = 0.00044
Silinder 7
6
4
x y
2 0 6.681
0 0.00044 6.681
0.0000 0.0010 0.0020 0.0030 0.0040 0.00044 0
Regangan (mm)

18

16

14

12
Tegangan (MPa)

10 Teg. maks (f'c) = 15.6435 MPa

Tegangan 0,5f'c = 6.25741 MPa
8
Tegangan 0,5f'c = 0.00040
6
Silinder 8
4
x y
2 0 6.257
0 0.00040 6.257
0.0000 0.0010 0.0020 0.0030 0.0040 0.00040 0
Regangan (mm)

20
Tegangan (MPa)

18
16
14
12
Teg. maks (f'c) = 17.2682 MPa
10 Tegangan 0,5f'c = 6.90729 MPa
8 Tegangan 0,5f'c = 0.00047
6
Silinder 9
4
x y
2 0 6.907
0 0.00047 6.907
0.0000 0.0010 0.0020 0.0030 0.0040 0.00047 0
Regangan (mm)
 25

Tegangan (MPa)
20

15 Teg. maks (f'c) = 21.7976 MPa

Tegangan 0,5f'c = 8.71904 MPa
Tegangan 0,5f'c = 0.00035
10 Silinder 10

5 x y
0 8.719
0 0.00035 8.719
0.0000 0.0010 0.0020 0.0030 0.0040 0.00035 0
Regangan (mm)

25

20

15
Tegangan (MPa)

Teg. maks (f'c) = 21.5098 MPa

Tegangan 0,5f'c = 8.60394 MPa
10 Tegangan 0,5f'c = 0.00040
Silinder 11
5
x y
0 8.604
0 0.0004 8.604
0.0000 0.0010 0.0020 0.0030 0.0040 0.00040 0
Regangan (mm)

25
Tegangan (MPa)

20

15
Teg. maks (f'c) = 21.2314 MPa
Tegangan 0,5f'c = 8.49257 MPa
10 Tegangan 0,5f'c = 0.00046

5
x y
0 8.493
0 0.00046 8.493
0.0000 0.0010 0.0020 0.0030 0.0040 0.00046 0
Regangan (mm)
 30

Tegangan (MPa)
25

20
Teg. maks (f'c) = 23.8125 MPa
15
Tegangan 0,5f'c = 9.52502 MPa
Tegangan 0,5f'c = 0.00046
Silinder 13
10

5 x y
0 9.525
0 0.00046 9.525
0.0000 0.0010 0.0020 0.0030 0.0040 0.00046 0
Regangan (mm)

25

20

15
Tegangan (MPa)

Teg. maks (f'c) = 23.2388 MPa

Tegangan 0,5f'c = 9.29550 MPa
10 Tegangan 0,5f'c = 0.00036
Silinder 14
5
x y
0 9.296
0 0.00036 9.296
0.0000 0.0010 0.0020 0.0030 0.0040 0.00036 0
Regangan (mm)

25
Tegangan (MPa)

20

15
Teg. maks (f'c) = 22.9299 MPa
Tegangan 0,4f'c = 9.17197 MPa
10 Regangan 0,4f'c = 0.00043

5
x y
0 9.172
0 0.00043 9.172
0.0000 0.0010 0.0020 0.0030 0.0040 0.0050 0.00043 0
Regangan (mm)
 HASIL ANALISIS KUAT TEKAN SILINDER MORTAR KARET (UMUR 28 HARI)

Nomor : 01 Diterima Tanggal :

Pengirim : Edward Ngii
Keperluan : Tugas Mata Kuliah S3 " Laboratory Work (3 sks)"

Tanggal Tinggi Sisi/diameter Berat b.j. Tanggal Umur Beban maks Kuat tekan Kuat tekan
No Tanda/Kode dibuat (kg) (kg/m3) diuji (hr) (kN) (MPa) rata2 (MPa)
(mm) (mm)
1 Var.1 (Ps.60%:Krt.40%) 7/29/2013 299 150 9.70 1836.74 8/26/2013 28 Err:509 Err:509
2 Var.1 (Ps.60%:Krt.40%) 7/29/2013 301 150 9.50 1786.92 8/26/2013 28 Err:509 Err:509 Err:509
3 Var.1 (Ps.60%:Krt.40%) 7/29/2013 298 150 9.40 1785.91 8/26/2013 28 Err:509 Err:509
4 Var.2 (Ps.70%:Krt.30%) 7/30/2013 299 150 9.80 1855.68 8/27/2013 28 Err:509 Err:509
5 Var.2 (Ps.70%:Krt.30%) 7/30/2013 302 149 9.90 1880.99 8/27/2013 28 Err:509 Err:509 Err:509
6 Var.2 (Ps.70%:Krt.30%) 7/30/2013 300 149 9.80 1874.40 8/27/2013 28 Err:509 Err:509
7 Var.3 (Ps.80%:Krt.20%) 7/30/2013 302 150 10.40 1949.73 8/27/2013 28 Err:509 Err:509
8 Var.3 (Ps.80%:Krt.20%) 7/30/2013 303 151 10.60 1954.52 8/27/2013 28 Err:509 Err:509 Err:509
9 Var.3 (Ps.80%:Krt.20%) 7/30/2013 303 150 10.50 1961.98 8/27/2013 28 Err:509 Err:509
10 Var.4 (Ps.90%:Krt.10%) 7/31/2013 301 150 10.80 2031.45 8/28/2013 28 Err:509 Err:509
11 Var.4 (Ps.90%:Krt.10%) 7/31/2013 300 151 10.90 2029.93 8/28/2013 28 Err:509 Err:509 Err:509
12 Var.4 (Ps.90%:Krt.10%) 7/31/2013 301 150 10.30 1937.40 8/28/2013 28 Err:509 Err:509
13 Var.5 (Ps.100%:Krt.0%) 7/31/2013 298 149 11.00 2118.04 8/28/2013 28 Err:509 Err:509
14 Var.5 (Ps.100%:Krt.0%) 7/31/2013 297 149 10.90 2105.85 8/28/2013 28 Err:509 Err:509 Err:509
15 Var.5 (Ps.100%:Krt.0%) 7/31/2013 299 150 11.10 2101.84 8/28/2013 28 Err:509 Err:509
Keterangan: (a) Tanggal dibuat diisi menurut informasi pengiriman benda uji (c) 1 MPa = 10 kg/cm2
(b) Kuat tekan silinder = 0,83 kuat tekan kubus
Yogyakarta,……………………….
Dikerjakan oleh, Kepala Laboratorium

Sukardi Ir. Kardiyono, M.E.

NIP. 130531214 NIP. 130530686
Setara Kubus
(MPa)

Err:509

Err:509

Err:509

Err:509

Err:509
 Tabel. Analisis modulus elastisitas sekan

Kode Perbandingan volume Modulus Rerata

bahan (%) Berat beton f'cmaks Regangan
Variasi benda uji Fas 0,4 f'c (MPa) elastisitas Esekan
(kg/m3) (MPa) 0,4 f'c
Esekan (MPa) (MPa)
Sand Rubber
SR 60/40 1836.74 10.757 4.3029 0.000340 12655.593
1 SR 60/40 60% 40% 0.550 1786.92 9.625 3.8500 0.000300 12833.215 12899.824
SR 60/40 1785.91 9.908 3.9632 0.000300 13210.663
SR 70/30 1855.68 11.607 4.6426 0.000380 12217.380
2 SR 70/30 70% 30% 0.580 1880.99 10.615 4.2461 0.000270 15726.271 14327.025
SR 70/30 1874.40 10.902 4.3609 0.000290 15037.422
SR 80/20 1949.73 16.702 6.6808 0.000440 15183.684
3 SR 80/20 80% 20% 0.610 1954.52 15.644 6.2574 0.000400 15643.520 15174.521
SR 80/20 1961.98 17.268 6.9073 0.000470 14696.361
SR 90/10 2031.45 21.798 8.7190 0.000350 24911.536
4 SR 90/10 90% 10% 0.630 2029.93 21.510 8.6039 0.000400 21509.840 21627.827
SR 90/10 1937.40 21.231 8.4926 0.000460 18462.107
SR 100/0 2118.04 23.813 9.5250 0.000460 20706.565
5 SR 100/0 100% 0% 0.690 2105.85 23.239 9.2955 0.000360 25820.837 22619.192
SR 100/0 2101.84 22.930 9.1720 0.000430 21330.173
 K u a t Len tu r R er a ta (M P a )
Tabel. Hasil pengujian kuat lentur rerata balok

Perbandingan volume Kuat Lentur

Variasi Kode Benda Uji bahan (%) Fas Rerata
Sand Rubber (MPa) penurunan f'r
3.0
1 B-SR60/40 60% 40% 0.550 1.191 -50.82 R² = 0.929694536
2.5
2 B-SR70/30 70% 30% 0.580 1.616 -33.27
2.0

3 B-SR80/20 80% 20% 0.610 1.869 -22.79 1.5

4 B-SR90/10 90% 10% 0.630 2.385 -1.49 1.0

0.5
5 B-SR100/0 100% 0% 0.690 2.421 0
0.0
0% 5% 10% 15% 20
Prose

Tabel. Hubungan antara kuat lentur dan berat beton

Perbandingan volume Berat Beton Kuat Lentur

Variasi Kode Benda Uji bahan (%) Fas Rerata Rerata
Sand Rubber (kg/m3) (MPa) penurunan bj
1 SR 60/40 60% 40% 0.550 1756.28 1.191 -16.35

2 SR 70/30 70% 30% 0.580 1897.68 1.616 -9.61

3 SR 80/20 80% 20% 0.610 1977.07 1.869 -5.83

 4 SR 90/10 90% 10% 0.630 2051.30 2.385 -2.30

5 SR 100/0 100% 0% 0.690 2099.52 2.421 0

Tabel. Hubungan antara kuat tekan dan kuat lentur

0.8
Perbandingan volume Kuat tekan (f'c) Kuat lentur (fr) Koefisien (α)
bahan (%) 0.7
Variasi Kode Benda Uji Fas

α = fr / √f'c
Sand Rubber (MPa) (MPa) (fr/√f'c) 0.6
1 CB-SR 60/40 60% 40% 0.550 10.10 1.191 0.375 0.5

2 CB-SR 70/30 70% 30% 0.580 11.04 1.616 0.486 0.4

3 CB-SR 80/20 80% 20% 0.610 16.54 1.869 0.460 0.3

0.2
4 CB-SR 90/10 90% 10% 0.630 21.51 2.385 0.514
0.1
5 CB-SR 100/0 100% 0% 0.690 23.33 2.421 0.501
0.0
0% 5% 10% 15% 20
Pro

Tabel. Hubungan antara kuat tekan dan kuat lentur

Perbandingan volume Hasil laboratorium SNI T-15-1991-03

Kode Benda Nilai √f'c
Variasi bahan (%) Fas Kuat lentur(f'r) Kuat tekan (f'c) Beton ringan Beton ringan total
Uji
Sand Rubber (MPa) (MPa) (MPa) (fr=0,70√f'c) (fr=0,525√f'c)
1 SR 60/40 60% 40% 0.550 1.191 10.097 3.178 2.224 1.668
2 SR 70/30 70% 30% 0.580 1.616 11.041 3.323 2.326 1.744

3 SR 80/20 80% 20% 0.610 1.869 16.538 4.067 2.847 2.135

4 SR 90/10 90% 10% 0.630 2.385 21.513 4.638 3.247 2.435

5 SR 100/0 100% 0% 0.690 2.421 23.327 4.830 3.381 2.536

Kuat lentur ( fr ) MPa

4.0

3.5

3.0

2.5
f(x) = 0.678287752913683 x − 0.821472808886412
2.0 R² = 0.94198961016482

1.5

1.0 Hasil
laboratorium
0.5

0.0
3 3.2 3.4 3.6 3.8 4 4.2 4.4 4.6 4.8 5
Kuat tekan ( √f'c ) MPa
 Tabel 1. Hasil pemeriksaan berat beton rata-rata
Berat s : 250 kg/m 3

Umur be: 1 hari

Benda u: Balok
Kode Silinder Berat Beton
Perbandingan volume
Variasi benda uji bahan (%) Panjang Lebar
rata2
Karet Pasir (cm) (cm) (kg/m3)
RA25-RS100/0 60.000 15.000
1 RA25-RS100/0 100% 0% 59.383 14.967 #REF!
RA25-RS100/0 59.967 15.000
RA25-RS80/20
2 RA25-RS80/20 80% 20%
RA25-RS80/20
RA25-RS60/40
3 RA25-RS60/40 60% 40%
RA25-RS60/40
RA25-RS40/60
4 RA25-RS40/60 40% 60%
RA25-RS40/60
RA25-RS20/80
5 RA25-RS20/80 20% 80%
RA25-RS20/80
RA25-RS0/100
6 RA25-RS0/100 0% 100%
RA25-RS0/100
K u a t Len tu r R er a ta (M P a )

3.0
R² = 0.929694536118073
2.5

2.0

1.5

1.0

0.5

0.0
0% 5% 10% 15% 20% 25% 30% 35% 40% 45%
Prosentase Karet
K u a t Len tu r R er a ta (M P a )

10%R
0%R

20%R
3.0
30%R
2.5
40%R
2.0

1.5

1.0

0.5

0.0
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150
Berat Beton Rerata (kg/m3)
 K u a t Le
3.0

2.5

2.0

1.5

1.0

0.5

0.0
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150
Berat Beton Rerata (kg/m3)

0.8
batas beton ringan (α=0,7)
0.7
batas beton ringan berpasri (α=0,595)
α = fr / √f'c

0.6 X Y
batas beton ringan total (α=0,525)
0.5 beton ringan (α = 0,7) 0 0.7

0.4 50% 0.7

0.3 beton ringan berpasir (α = 0,595) 0 0.595
0.2
50% 0.595
0.1
beton ringan total (α = 0,525) 0 0.525
0.0
0% 5% 10% 15% 20% 25% 30% 35% 40% 45% 50% 50% 0.525

Prosentase Karet

Δ fr Δ f'c
-50.815 -56.717 6 Nilai kuat tekan dan lentur berdasarkan umur 28 hari
-33.273 -52.667 19 harusnya dibuat berdasarkan umur, sehingga

-22.786 -29.104 7 terlihat pengaruh penambahan karet pada umur beton

-1.489 -7.777 6

0.000 0.0000