Scribd
Upload
156 views5 pages

Design of RCC Deck Slab:: 1. Material Details

The document describes the design of an RCC deck slab including material properties, reinforcement details, applied forces, analytical modeling, and checks for moment capacity, shear capacity, and serviceability of the section. Key information provided includes concrete grade of C30/20, bottom reinforcement of 16mm bars at 100mm spacing, maximum design moment of 95.9 kNm and maximum shear force of 110 kN.

Uploaded by

Anonymous wosn1ly
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
156 views5 pages

Design of RCC Deck Slab:: 1. Material Details

The document describes the design of an RCC deck slab including material properties, reinforcement details, applied forces, analytical modeling, and checks for moment capacity, shear capacity, and serviceability of the section. Key information provided includes concrete grade of C30/20, bottom reinforcement of 16mm bars at 100mm spacing, maximum design moment of 95.9 kNm and maximum shear force of 110 kN.

Uploaded by

Anonymous wosn1ly
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Design of RCC Deck Slab :

1. Material Details
1.3 Concrete :
Grade of concrete = C30/20
Modulus of elasticity Ecm = 28000 MPa
Characteristic strength = 30.00 MPa
Material safety factor gm = 1.50
Depth Of Deck Slab 250 mm
1.4 Steel :
Grade of Longitudinal reinforcement = 460 MPa
Modulus of elasticity = 200000 MPa
Material safety factor gs = 1.15
Design yield strength fyd = 400.00 MPa
Design yield strain eyd = 0.0020
Permissible tension stress = 345.00 MPa
Modular Ratio, m for Serviceability = 15.00
11400

1500 2800 2800 2800 1500


Typical cross section of the Superstructure

Clear cover for Deck Slab 40.0 mm


Diameter of Distribution steel 12.0 mm
2.2 Reinforcement details :
Bottom reinforcement detail
Effective Effective
CG from Depth, CG of
Layer No. Diameter Spacing Area
Bottom di Reinforcem
ent
(mm) (mm) (mm2 ) (mm) (mm) (mm)
S1 16 100 2010.62 60.00 190.00
190.000
S= 2010.62 1.06 %

3. Applied forces :
Moment
Load Case Shear (kN)
(kNm)
ULS DL (Max) 7.8 10.6 (From STAAD OUTPUT)
ULS (Max) 95.9 110.0
SLS (Max) 87.2 100.0

3.1 Analytical Model(STAAD) :

1.55m

2.80m

2.80m

2.80m

1.55m

Y
4. Determination of Moment capacity of the Section :

4.1 Deck Slab section (Ultimate Limit State of failure) :


1000
250

Moment of resistance of the section (Mu,lim)= 0.87 fy As Z


(As per eq. 1, BS 5400: Part4-1990) = 125.6 kN-m
The Lever arm, Z = = 156.088 mm
Design moment = 95.9 kN-m Hence O.K.
5. Determination of Shear capacity of the Section :

(As per Cl no. 5.3.3, BS 5400: Part4-1990)


5.1 Calculation of shear reinforcement:
Nominal shear stress v = V/bd = 0.44 Mpa
Ultimate shear stress in concrete (vc) = 0.68 Mpa
(As per Table 8, BS 5400: Part4-1990)
Depth factor (ξs) = 0.70
(As per Table 9, BS 5400: Part4-1990)
ξs vc = 0.48 Mpa No Shear Reinforcement is required

5.2 Check for punching shear :

Punching shear stress v = V/bd = 0.39 Mpa


Ultimate shear stress in concrete (vc) = 0.68 Mpa
(As per Table 8, BS 5400: Part4-1990)
Depth factor (ξs) = 0.70
(As per Table 9, BS 5400: Part4-1990)
ξs vc = 0.48 Mpa Safe against punching shear
6. Check for Serviceability of the section

6.1 Deck Slab section (stress check):


1000 8.517
250
0.00030 345.2 kN
81.06

345.20 kN
0.0013

Strain Diagram Stress Diagram

Neutral axis depth = 81.1 mm Stress at extreme compression fiber = 8.52 MPa
2
Concrete under compression = 81061.7041 mm Stress at Reinforcing bars = 171.7 MPa
Compressive force, C = 345.20 kN Total tensile force = 345.20 kN
Moment of Resistance, Mr = 56.26 kNm Applied moment = 87.2 kNm
Difference in Force, C-T = 0.00 kN Difference in Moment = -30.96 kNm

Total compressive stress at top of deck =8.5 = 8.52 MPa


Hence O.K.
6.2 Deck Slab section (crack width check):-
s

cmin acr1

Tensile strain at the beam soffit e1 = 0.00063 0.000858


Steel strain ignoring tension stiffening es = 0.00135
< design yield strain of 0.002001
Width of section at level of tension steel, bt = 625.0 mm
Overall depth of the section, h = 250.0 mm
Distance from the compression face to the point at which crack width is being calculated, a'
= 250.0 mm
Depth of the concrete in compression,dc = 81.1 mm
Area of tension steel, As = 2010.6 mm2
Moment due to permanent load, Mg = 7.8 kN-m
Moment due to live load, Mq = 15.0 kN-m

Strain due to tension stiffening, em = e1 - [3.8bth(a'-dc)/{esAs(h-dc)}] [(1-Mq/Mg)10-9]


(As per eq. 25, BS 5400: Part4-1990) = 0.00084
Cover to center reinf. = 60.0 mm
Cover to outermost reinforcement, Cnom = 52.0 mm
Spacing of bar, s = 100.0 mm
Distance from the crack to reinforcement acr = 70.1 mm
(at a location equidistant from two bars)
3acrεm
Design surface crack =
1 2 acr  cnom / h  dc 

= 3 * 70.1 * 0.00084 / (1 + 2 * 10.1 / 168.94) = 0.145 mm


Hence O.K.

7. STAAD INPUT FILE:

STAAD SPACE
START JOB INFORMATION
ENGINEER DATE 05-Nov-20
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 1.55 0 0; 3 4.35 0 0; 4 7.15 0 0; 5 9.95 0 0; 7 11.5 0 0;
9 9.525 0 0; 10 4.487 0 0; 11 6.999 0 0; 12 1.975 0 0; 13 5.75 0 0;
14 6.25 0 0; 15 5.25 0 0; 16 7.25 0 0; 17 4.25 0 0;
MEMBER INCIDENCES
1 1 2; 2 2 12; 3 3 10; 4 4 16; 5 5 7; 7 9 5; 8 10 15; 9 11 4; 10 12 17;
11 13 14; 12 14 11; 13 15 13; 14 16 9; 15 17 3;
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.17185e+007
POISSON 0.17
DENSITY 26
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
MEMBER PROPERTY AMERICAN
1 TO 5 7 TO 15 PRIS YD 0.25 ZD 1
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
2 TO 5 PINNED
LOAD 1 LOADTYPE Dead TITLE DL
SELFWEIGHT Y -1 LIST 1 TO 5 7 TO 15
LOAD 2 LOADTYPE Dead TITLE SIDL-WC
MEMBER LOAD
3 4 8 TO 15 UNI GY -2.2
LOAD 3 LOADTYPE Dead TITLE SIDL-FIXED
JOINT LOAD
1 7 FY -7.5
LOAD 4 LOADTYPE Dead TITLE UTILITY
MEMBER LOAD
1 5 UNI GY -26.62
LOAD 5 LOADTYPE Live TITLE FPLL
MEMBER LOAD
1 5 UNI GY -7.25
LOAD 6 LOADTYPE Live TITLE HA-LL-TWO LANE ECCENTRIC
MEMBER LOAD
3 8 10 TO 13 15 UNI GY -45.14
LOAD 7 LOADTYPE Live TITLE HA-LL-THREE LANE CONCENTRIC
MEMBER LOAD
3 8 10 TO 13 15 UNI GY -45.14
4 9 14 UNI GY -39.25
LOAD 8 LOADTYPE Live TITLE HA-KEL-TWO LANE ECCENTRIC
MEMBER LOAD
3 8 10 TO 13 15 UNI GY -33.12
LOAD 9 LOADTYPE Live TITLE HA-KEL-THREE LANE CONCENTRIC
MEMBER LOAD
3 8 10 TO 13 15 UNI GY -33.12
4 9 14 UNI GY -28.8
LOAD 10 LOADTYPE Live TITLE HB-ALONE
MEMBER LOAD
10 UNI GY -89.3 1.93 2.275
3 4 9 15 UNI GY -89.3
8 UNI GY -89.3 0 0.11
8 UNI GY -89.3 0.41 0.76
13 UNI GY -89.3 0 0.35
11 UNI GY -89.3 0.15 0.5
12 14 UNI GY -89.3 0 0.35
12 UNI GY -89.3 0.65 0.75
LOAD 11 LOADTYPE Live TITLE HA+HB-ONE LANE ECCENTRIC
MEMBER LOAD
10 UNI GY -89.3 1.93 2.275
3 4 9 15 UNI GY -89.3
8 UNI GY -89.3 0 0.11
8 UNI GY -89.3 0.41 0.76
13 UNI GY -89.3 0 0.35
11 UNI GY -89.3 0.15 0.5
12 14 UNI GY -89.3 0 0.35
12 UNI GY -89.3 0.65 0.75
3 10 15 UNI GY -45.14
LOAD 12 LOADTYPE Live TITLE HA+HB-ONE LANE CONCENTRIC
MEMBER LOAD
10 UNI GY -89.3 1.93 2.275
3 4 9 15 UNI GY -89.3
8 UNI GY -89.3 0 0.11
8 UNI GY -89.3 0.41 0.76
13 UNI GY -89.3 0 0.35
11 UNI GY -89.3 0.15 0.5
12 14 UNI GY -89.3 0 0.35
12 UNI GY -89.3 0.65 0.75
8 11 TO 13 UNI GY -45.14
PERFORM ANALYSIS
FINISH

You might also like