Technical values for fastener from

SFS intec

Pitched roofing and

cladding fastening
systems for the
constructions industry
 O Tensile breaking load
The tensile breaking load Zb is the
breaking load of the fastener in this axial
direction. It is dependent only upon the
type of fastener.

O Shear breaking load

The shear breaking load Qb is the breaking
load of the fastener perpendicular to its
axis. It is dependent only upon the type of
fastener.

O Pull-out load
The pull-out value Fz is the load whic must
be exerted in the axial direction of the fa-
stener to pull the fastening out of the sub-
structure. It is dependent only upon the
type of fastener and the substructure.

Part I
O Pull over load
The pull over value Fu is the load which
must be exerted in the axial direction of
the fastener to cause the failure of the
attached material by pulling it over the
head of the fastener. It is dependent only
upon the type of fastener and the
substructure and the material being
Part II attached.

O Shear load
The shear load value Fq ist the load which
must be exterted perpendicular to the or-
ginal axis of the fastener to cause the fai-
lure of the substructure or of the material
being atteched. It is dependent only upon Legend:
the type of fastener and the substructure St37 = 375 N/mm2
and the material being attached. St52 = 530 N/mm2
Alu = 230 N/mm2

-2-
Content

Roofing and cladding

External single and twin self-drilling fastener in SX

skin construction stainless steel and aluminium SXC
SXW
SW-S
SW-A
SXL
SL-S
SL-A
self tapper TDA-S
in stainless steel TDB-S
TDC-S
self-drilling-fastener SDT, SDP, SDTW, SD, SDC, SDL
corrosion protected SW-T
SL
self tapper TDA-T
corrosion protected TDB-T
TDBL

Standing seam and stainless steel self drilling

secret fix systems fastener, self tapper, SDK
Bulb-Tite SX
SXW
SX6/SX12
RV6604

Standing seam and stainless steel self drilling

secret fix systems fastener, self tapper SXC
SXCW
TD-S
SXL
SL-S
Fibre cement self-drilling fastener to wood
self-drilling fastener to steel SCFW
SCFW-S
SCF3/SCF12
Special fastener and rivets Bulb-Tite, blind rivets,
scafolding anchors TT/TTN
ASO
ASC
ATO
ATC
TTO
SSC
CNSO
GA-AS
GA-BS
Content

Rainscreen cladding Sleeve anchor, Nylon frame MB (SDF-K)

plug, self-drilling fastener, MBR (SDF-S)
rivet, facade screw TW-S/TW-A4
AP11
AP14
AP16
SDA3-S
SLA5
TU-S
 Technical value August/2003 sre/abjo

SX2
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) –x s

St37 (375 N/mm ) 2
1,25 2905 58
SX2 St52 (530 N/mm ) 2
1,25 3584 76
Ø 6,3xL

Admission: no

Pull-over load Fu (N) Part II

Material
Fastener:
stainless steel A2, 18/8
Material number 1.4301, AISI 304
Part I
Washer:
stainless steel A2, 18/8 Washer A14
Material number 1.4301, AISI 304
with vulcanized EPDM Material Sheet thickness
Part I
Size –x
(mm) s
Head/Drive:
- Hex., 8 mm A/F Alu (230 N/mm )
2
2,0 7419 316

Tensile breaking load Zb (N)

x = 16000

Shear breaking load Qb (N)

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

SX3

Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) –x s

S235 (375 N/mm ) 2
1,0 1500 90
1,5 2700 110
SX3 SX3–L12 SX3–D12 2,0 3800 140
Ø 5,5xL Ø 5,5xL Ø 5,5xL 2,5 5000 170
2x0,63 1900 40
2x0,75 2300 70
Admission: SX3 2x1,0 3300 100
SX3-L12 2x1,25 4300 130

DIBt Z-14.1-4 S355 (530 N/mm ) 2

1,0 2100 90
Material 1,25 3008 66
Fastener: 1,5 3500 120
stainless steel A2, 18/8 2,0 5200 140
Material number 1.4301, AISI 304 2,5 8400 190
2x0,63 2300 320
Washer: 2x0,75 2800 300
stainless steel A2, 18/8 2x1,0 4000 250
Material number 1.4301, AISI 304 2x1,25 5100 200
with vulcanized EPDM Alu (230 N/mm2) 1,5 2100 80
2,0 2900 110
Size 2,5 3800 130
Head/Drive: 2x0,63 1000 70
- Hex., 8 mm A/F 2x0,75 1600 120
- L12 Head (Ø 12 mm) irius® Drive 2x1,0 2300 160
- D12 pan head (Ø 12 mm) Torx T25 2x1,2 3100 200

Tensile breaking load Zb (N)

x = 14000

Shear breaking load Qb (N)

x = 9500

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

SX3
Pull-over load Fu (N) Part II

Part I

Washer A10/12 Washer S16 Washer S19 Washer S22

Material Blechdicke
Part I
(mm) x s x s x s x s
S235 0,5 -- -- 5800 1 200 58001 200 – –
(375 N/mm2) 0,63 -- -- 5800 200 5800 200 – –
0,7 -- -- 5800 200 5800 200 – –
0,75 -- -- 5800 200 5800 200 – –
0,88 -- -- 5800 200 5800 200 – –
1,0 -- -- 5800 200 5800 200 – –
S355 0,4 -- -- 3400 340 4300 370 – –
0,5 -- -- 4500 230 5000 200 -- --
(530 N/mm2) 0,63 -- -- 6200 100 8400 1 190 – –
0,7 -- -- 8400 1 190 8400 190 – –
0,75 -- -- 8400 190 8400 190 – –
0,88 -- -- 8400 190 8400 190 – –
1,0 -- -- 8400 190 8400 190 – –
Aluminium 0,4 -- -- 1800 280 2500 420 2800 230
(230 N/mm2) 0,5 722 101 2100 270 2850 440 3200 600
0,6 -- -- 2400 255 3200 470 3600 290
0,7 -- -- 2650 240 3500 500 3900 320
0,8 2297 196 2950 230 3800 530 4900 350
1 = Pull-over load fail in Part I 0,9 -- -- 3200 200 4150 560 4650 385
1,0 -- -- 3500 200 4500 590 5000 420
1,25 3000 82 -- -- --- -- --- --

Shear load FQ (N)

Thickness in mm Washer S16 Washer S19 Washer A12

–
Material Part I Part II x– s x– s x s
S235 0,63 0,75 2150 320 – – - -
(375 N/mm2) 0,63 2x0,63 2430 370 2360 200 - -
0,63 1,5 3040 220 – – - -
0,63 2,0 3580 200 – – - -
0,63 2x1,25 2170 315 – – - -
0,75 2x0,75 3220 570 3190 330 - -
0,75 1,5 4270 235 – – - -
0,75 2x1,25 3770 320 – – - -
1,0 1,0 3000 260 – – - -
1,0 1,5 5020 610 – – - -
1,0 2x1,0 4300 315 4380 140 - -
1,0 2 4800 290 – – - -
1,0 2x1,25 6140 780 – – - -
1,25 1,25 - - - - 3792 280
1,25 1,5 6160 435 – – - -
Alu 0,5 0,8 1200 100 1200 450 - -
(230 N/mm2) 0,5 1,0 1500 170 1750 100 - -
0,5 2,0 1200 120 1800 200 - -
Shear load: Figures obtained with displa-
0,8 2,0 2500 180 3000 150 - -
cement of 3 mm between purlin and sheet.
1,0 1,0 2300 120 2000 450 - -
1,0 2,0 3800 320 3800 300 - -

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

SX5/SXL5
Pull out load FZ (N)

Part II (sub-construction)

Material Thickness (mm) –x s

S235 (375 N/mm ) 2
0,75 905 124
0,88 1131 133
1,00 1194 73
SXL5 SX5 1,25 1942 77
5,5xL 5,5xL 1,50 2691 95
2,00 4037 124
2,50 5378 281
S355 (530 N/mm2) 0,75 1081 120
Material 1,00 1864 96
Fastener: 1,25 2198 121
stainless steel A2, 18/8 1,50 3365 160
Material number 1.4301, AISI 304 2,00 5403 450
2,50 7068 108
Washer:
stainless steel A2, 18/8
Material number 1.4301, AISI 304 Pull-over load Fu (N) Part II
with vulcanized EPDM EPDM

Size Part I
Head / drive:
hexagon, 8 mm A/F Washer S16

Material Thickness sheet part I (mm) x s

S235 0,50 4026 279
(375 N/mm2) 0,63 5415 311
0,75 6972 295
0,88 7694 511
1,00 8930 448

Shear load FQ (N)

Thickness in mm washer S16

–
Material Part I Part II x s
S235 (375 N/mm )
2
0,50 0,50 837 86
0,50 1,25 1533 136
1,00 2,50 3623 320
Shear load:
Figures obtained with displacement of S355 (530N/mm )2
0,50 1,25 1903 233
3 mm between purlin and sheet. 1,00 2,50 5700 461

Shear breaking Tensile breaking

load Qb (N) load Zb (N)

x = 8139 x = 11227

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value April/2006 sre/abjo

SX6
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) –x s

S235 2,0 2900 140
(375 N/mm2) 2,5 4300 220
SX6 SX6–L12 SX6–D12
3,0 5600 300
Ø 5,5xL Ø 5,5xL Ø 5,5xL
4,0 8500 460
5,0 11500 630
6,0 14100 800
S355 2,0 4200 210
Admission SX6
(530 N/mm2) 2,5 5500 310
SX6-L12
3,0 6800 410
4,0 9200 660
DIBt Z-14.1-4
5,0 11700 850
6,0 14200 1100
Material
Fastener: Alu 3,0 3600 220
stainless steel A2, 18/8 (230 N/mm2) 4,0 5300 350
Material number 1.4301, AISI 304 5,0 6700 470
6,0 8300 580
Washer:
stainless steel A2, 18/8
Material number 1.4301, AISI 304
with vulcanized EPDM
Shear breaking load Qb (N)
Size
Head/Drive:
- Hex., 8 mm A/F
- L12 Head (Ø 12 mm) irius® Drive
- D12 Head (Ø 12 mm) Torx T25

x = 9500

Tensile breaking load Zb (N)

x = 14000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value April/2006 sre/abjo

SX6
Pull-over load Fu (N) Part II

Part I

Washer S16 Washer S19 Washer S22

Material Blechdicke
Part I
–x –x –x
(mm) s s s
S235 0,4 3000 400 4200 270 – –
(375 N/mm2) 0,5 4000 380 5100 300 – –
0,63 5300 360 6200 340 – –
0,7 6000 350 6800 360 – –
0,75 6200 340 7200 380 – –
0,88 7500 330 8400 410 – –
1,0 8500 320 9500 440 – –
S355 0,4 3200 440 3700 200 – –
(530 N/mm2) 0,5 4300 520 5000 320 – –
0,63 6200 620 7100 470 – –
0,7 6900 650 7000 560 – –
0,75 7300 680 8100 640 – –
0,88 9000 750 9600 830 – –
1,0 10600 800 10900 970 – –
Alu 0,4 1200 90 1800 110 2300 480
(230 N/mm2) 0,5 1500 110 2100 170 2800 470
0,6 1900 135 2600 230 3200 460
0,7 2300 175 3100 290 3700 450
0,8 2700 200 3500 355 4150 440
0,9 3100 230 3900 420 4600 430
1,0 3500 260 4300 480 5000 420

Shear load FQ (N)

Thickness in mm Washer S16 Washer S19

– –
Material Part I Part II x s x s
S235 0,63 1,5 – – 2300 240
(375 N/mm2) 0,63 2,0 2800 100 2400 230
0,63 3,0 – – 2600 220
0,63 5,0 3200 50 2800 210
0,63 6,0 – – 3100 190
0,75 1,5 – – 3150 340
0,75 2,0 2900 50 3200 330
0,75 3,0 – – 3300 310
0,75 5,0 3250 50 3500 270
0,75 6,0 – – 3600 250
0,88 2,0 4200 200 3700 330
0,88 6,0 4300 50 4700 160
1,0 1,5 – – 4000 500
1,0 2,0 4600 250 4200 470
1,0 3,0 – – 4400 430
1,0 5,0 5000 320 4700 340
1,0 6,0 – – 5000 300
1,25 1,5 – – 4600 600
Shear load: Figures obtained with displa- 1,25 3,0 – – 5500 550
cement of 3 mm between purlin and sheet. 1,25 5,0 – – 65000 480
1,5 1,5 – – 5600 500
1,5 5,0 – – 8100 600

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Februar/2004 sre/abjo

SXC
Pull-out load FZ (N)

Part II (Subconstruction)

Type –
Material Thickness (mm) x s
SXC5 St37 (375 N/mm )
2
1,5 2300 85
2,0 4000 150
3,0 7200 185
4,0 10280 1035
SXC14 St37 (375 N/mm )
2
4,0 10100 340
5,0 12700 1015

SXC5 SXC14 Pull-over load Fu (N) Part II

Ø 5,5xL Ø 5,5xL

Admission SXC5
SXC14
Part I
DIBt Z-14.4-407

Material Type St37(375 N/mm )2

Washer S19 Type Aluminium Washer S19
Fastener SXC5: Blechdicke Blechdicke
–x
stainless steel A2, 18/8 Part I(mm) s Part I(mm) x– s
Material number 1.4301, AISI 304 SXC5 0,50 4150 500 SXC5 0,50 1370 123
Fastener SXC14: 0,63 5100 650 0,63 1990 260
stainless steel A2, 18/8 0,75 7040 860 0,75 2150 238
Material number 1.4567 0,88 7140 730 0,88 2700 311
Washer: 1,00 3350 285
stainless steel A2, 18/8
Material number 1.4301, AISI 304 SXC14 0,50 3700 382 SXC14 0,50 1410 114
with vulcanized EPDM 0,63 5100 535 0,63 1960 124
Size 0,75 6100 610 0,75 2290 175
Head/Drive: 0,88 2850 205
- Hex., 8 mm A/F 1,00 3260 384
- L12 Head (Ø 12 mm) irius® Drive

Max. deflection (mm)

Shear breaking load Qb (N)

St37

Panele thickness (mm) 1,5 mm ≤ t ≤ 4 mm 4 mm ≤ t ≤ 12mm

SXC5 x = 10900 SXC5 a (mm) SXC14 a (mm)
SXC14 x = 12400 40 4 3,2
60 6 4,3
Tensile breaking load Zb (N) 80 8 5,7

x = arithmetical mean value

s = Standard deviation

SXC5 x = 17500 All stated values are x values, representing the arithmetical mean value from laboratory
SXC14 x = 14000 testing concluded up to now, appropriate safety margins should be applied for field
conditions. Consult also your country’s approval documents.
 Technical value Januar/2005 sre/pko

SXC, L ≥ 168 mm

Pull-out load FZ (N)

Part II (Subconstruction)

Type Material Thickness (mm) x– s

SXC14-5,5 x St37 (375 N/mm )
2
4,0 7350 630
≥ 168 mm 5,0 8800 1000
6,0 9810 1550

SXC14
Ø 5,5x L ≥ 168 Pull-over load Fu (N) Part II

Part I

Admission SXC14 Washer S19

Type St37(375 N/mm )
2
Washer S19 Type Aluminium
DIBt Z-14.4-407
Thickness Thickness
–x
Part I(mm) s Part I(mm) x– s
Material
Fastener SXC14: SXC14 0,50 3700 382 SXC14 0,50 1410 114
stainless steel A2, 18/8 L ≥ 168 mm 0,63 5100 0,63 L ≥ 168 mm 0,63 1960 124
Material number 1.4567 0,75 6100 610 0,75 2290 175
Washer: 0,88 2850 205
stainless steel A2, 18/8 1,00 3260 384
Material number 1.4301, AISI 304
with vulcanized EPDM
Size
Head/Drive:
- Hex., 8 mm A/F Tensile breaking load Zb (N)

SXC14 L ≥ 168 mm x = 12000

Shear breaking load Qb (N)

SXC14 L ≥ 168 mm x = 17700

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value April/2006 sre/abjo

SX14
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) –x s

S235 (375 N/mm ) 2

4,0 10000 365
5,0 11800 630
SX14 6,0 12200 130
SX14-L12
Ø 5,5xL Ø 5,5xL S355 (520 N/mm ) 2
4,0 8288 982
Admission SX14 (530 N/mm2) 5,0 9334 962
DIBt Z-14.1-4 (550 N/mm2) 6,0 11413 578

Material Alu (230 N/mm )

2
4,0 4755 560
Fastener: 5,0 5300 400
stainless steel A2, 18/8
Material number 1.4567

Washer:
stainless steel A2, 18/8
Material number 1.4301, AISI 304
with vulcanized EPDM Shear load FQ (N)
Size
Head/Drive:
- Hex., 8 mm A/F
- L12 Head (Ø 12 mm) irius® Drive

Thickness in mm Washer S16 Washer S19

–
Material Part I Part II x s x– s
S235 (375 N/mm ) 2
0,63 4,0 3136 168 - -
Shear load: Figures obtained with displace- 0,75 4,0 3860 75 - -
ment of 3 mm between purlin and sheet. 0,75 5,0 3800 100 - -

Tensile breaking load Zb (N)

x = 12000

Shear breaking load Qb (N)

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SXW
Pull-out load FZ (N)

Part II (Subconstruction)
Embedment (mm)
Wood 20 25 30 45
–x s x– s x– s x– s
SXW- Ø 5,5 1700 190 2100 300 2500 200 – –
SXW- Ø 6,5 – – – – – – 3600 210

SXW SXW-L12
Ø 5,5xL Ø 5,5xL Pull-over load Fu (N)
Ø 6,5xL Part II
Ø 6,5xL
Admission SXW
DIBt Z-14.1-4 Part I

Material Washer S 16 Washer S 16 Washer S 16

Fastener:
Material Thickness (mm) 0,5 0,5 0,75 0,75 0,88 0,88
stainless steel A2, 18/8
Material number 1.4301, AISI 304 –x x– –x
s s s
Washer: St37 SXW-S16-6,5x 4000 270 6200 – 7500 –
stainless steel A2, 18/8 (375 N/mm2)
Material number 1.4301, AISI 304
with vulcanized EPDM Alu SXW-S16-6,5x 1500 2700 3100 –
Alu, with vulcanized EPDM (230 N/mm2)

Size
Head/Drive: Shear load FQ (N)
- Hex., 8 mm A/F
bei SXW und SW-S
- L12 Head (Ø 12 mm) irius® Drive

Material Thickness (mm) 0,5 0,5 0,77 0,77 0,88 0,88

–x x– –x
s s s

St37 SXW-A14- Ø 5,5 1800 130 2200 255 2500 370

(375 N/mm2) SXW-S16- Ø 6,5 2400 – 3000 – 4900 –
Shear load: Figures obtained with displa-
cement of 3 mm between purlin and sheet.
Alu SXW-A14- Ø 5,5 880 78 1500 85 – –
(230 N/mm2) SXW-S16- Ø 6,5 1200 – 2000 – – –

Tensile breaking load Zb (N)

SXW Ø 5,5 x = 14000

SXW Ø 6,5 x = 16000

x = arithmetical mean value Shear breaking load Qb (N)

s = Standard deviation

All stated values are x values, representing the arithmetical mean value from laboratory SXW Ø 5,5 x = 9500
testing concluded up to now, appropriate safety margins should be applied for field SXW Ø 6,5 x = 12000
conditions. Consult also your country’s approval documents.
 Technical value August/2004 sre/abjo

SXW Ø 6,5

Pull-out load FZ (N)

Part II (Subconstruction)

Material x s
Wood Embedment 50 mm 5356 355

SXW
Ø 6,5xL Pull-over load Fu (N) Part II

Material
Fastener: Part I
stainless steel A2, 18/8
Material number 1.4301, AISI 304 Washer S 16 Washer S 19

Washer: Material Thickness (mm) x s x s

stainless steel A2, 18/8 St. 37 0,63 5460 369 6310 414
Material number 1.4301, AISI 304 St. 37 0,75 6938 619 7535 576
with vulcanized EPDM Alu 1,00 4027 339 4685 443
Alu, with vulcanized EPDM

Size
Head/Drive:
- Hex., 8 mm A/F

Tensile breaking load Zb (N)

x = 17100

Shear breaking load Qb (N)

x = 12300

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value September 2004 sre/pko

SW2-S

Pull-out load FZ (N)

Part II (Subconstruction)

Material Embedment (mm) –x s

Timber 25 1625 102
30 2030 53
SW2-S
Ø 4,8xL Alu 2 mm 25 2360 31
(240-280 N/mm2)

Material
Fastener:
stainless steel A2, 18/8
Material number 1.4301, AISI 304

Washer:
Pull-over load Fu (N) Teil II
stainless steel A2, 18/8
Material number 1.4301, AISI 304
with vulcanized EPDM Teil I
Alu, with vulcanized EPDM
Washer A14
Size
Material Thickness (mm) x s
Head/Drive:
- Hex., 8 mm A/F St. 37 0,50 2260 150

Tensile breaking load Zb (N)

x = 9234

Shear breaking load Qb (N)

x = 6653

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

NK-A / SW-A
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s

Wood 20 1790 390

25 2190 270
NK-A SW-A 30 2840 160
Ø 6,0xL Ø 6,0xL
Material Pull-over load Fu (N) Part II
Fastener:
Alu

Washer:
Alu, with vulcanized EPDM
Part I
Size Washer A16
Head/Drive:
Material Thickness
Hex., 8 mm A/F
Part I
–x
(mm) s
Alu (230 N/mm )2
0,50 2140 190

Alu (230 N/mm )2

0,75 2450 170
Alu (230 N/mm )2
0,80 2840 -

Shear load FQ (N)

Thickness in mm Washer A16

–
Material Part I Part II x s

Shear load: Figures obtained with displa- Wood/Alu 40 0,5 1460 100
cement of 3 mm between purlin and sheet. (230 N/mm2) 0,8 1700 120

Tensile breaking load Zb (N)

NK-A x = 6500
SW-A x = 6500

Shear breaking load Qb (N)

NK-A x = 4200
SW-A x = 4200

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value
testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation
conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SXL2-Ø 5,5

Pull-out load FZ (N)

Part II (Subconstruction)
SXL2 SXL2–L12 –
Material Thickness (mm) x s
Ø 5,5xL Ø 5,5xL
St37 0,40 573 36
(375 N/mm2) 2x0,50 660 50
2x0,75 940 98
Admission SXL2
DIBt Z-14.1-4

Material
Fastener:
Shear load FQ (N)
stainless steel A2, 18/8
Material number 1.4301, AISI 304

Washer:
stainless steel A2, 18/8
Material number 1.4301, AISI 304
Thickness in mm Washer S14
with vulcanized EPDM
Material Part I Part II –x s
Size
St37 (375 N/mm )
2
0,6 0,6 1400 129
Head/Drive:
- Hex., 8 mm A/F
- L12 Head (Ø 12 mm) irius® Drive

Shear load: Figures obtained with displa-

cement of 3 mm between purlin and sheet. Tensile breaking load Zb (N)

x = 14000

Shear breaking load Qb (N)

x = 9500

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value January 2006 sre/abjo

SXL2-Ø 6,3

Pull-out load FZ (N)

Bauteil II (Unterkonstruktion)
SXL2 SXL2–L12 –
Material Dicke (mm) x s
Ø 6,3xL Ø 6,3xL
St37 0,62 1166 30
(375 N/mm2) 0,75 1563 76

Material
Fastener:
stainless steel A2, 18/8
Material number 1.4301, AISI 304 Pull-over load Fu (N) Part II

Washer:
stainless steel A2, 18/8
Material number 1.4301, AISI 304
with vulcanized EPDM
Part I
Size WasherS16
Head/Drive:
Material Sheet thickness
- Hex., 8 mm A/F
Part I
- L12 Head (Ø 12 mm) irius® Drive
(mm) x– s
St37 (375 N/mm2) 0,62 4980 314

Shear load FQ (N)

Thickness in mm Washer S16

Shear load: Figures obtained with displa- Material Part I Part II –x s
cement of 3 mm between purlin and sheet.
St37 (375 N/mm )2
1,0 1,0 3940 195

Shear breaking load Qb (N)

x = 13500

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SL2-A

Pull-out load FZ (N)

SL2-A
Ø 5,5xL Part II (Subconstruction)
–
Material Thickness (mm) x s
Material
Alu (230 N/mm ) 2
2x0,7 550 35
Fastener:
Aluminium

Washer:
Aluminium, with vulcanized EPDM
Shear load FQ (N)
Size
Head/Drive:
Hex., 8 mm A/F

Thickness in mm Washer A14

Material Part I Part II –x s

Shear load: Figures obtained with displa- Alu (230 N/mm )

2
0,4 0,4 400 50
cement of 3 mm between purlin and sheet. 0,7 0,7 910 110

Tensile breaking load Zb (N)

x = 5000

Shear breaking load Qb (N)

x = 3500

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value July/2005 sre/abjo

TDA-S
Pull-out load FZ (N)

Part II (Subconstruction)

Material Sheet thickness (mm) Pre drill Ø

– –
Embedment (mm) (mm) x s x s
Alu 3,0 4,50 3400 52 – –

TDA-S St37 0,75 4,50 1091 33 - -

Ø 6,5xL (375 N/mm2) 1,00 4,50 2290 - - -
1,50 4,50 2745 81 - -
1,50 5,05 4070 - - -
Admission TDA-S
2,00 5,05 5400 - - -
DIBt Z-14.1-4
2,50 5,05 7920 - - -
Material 3,00 5,05 9750 - - -
Fastener: Wood 25 4,80 2320 - - -
stainless steel A2, 18/8 30 4,80 3360 - - -
Material number 1.4301, AISI 304 40 4,80 4170 - - -
50 4,80 5720 - - -
Washer:
stainless steel A2, 18/8 Pull-over load Fu (N) Part II
Material number 1.4301, AISI 304
with vulcanized EPDM

Size Part I
Head/Drive:
Hex., 8 mm A/F Washer S16 Washer S19
Material Blechdicke
Part I
–x –x
(mm) s s
St37 0,5 4060 – 5145 –
(375 N/mm2) 0,63 5500 – 6560 –
0,75 5920 – 6805 –
0,88 7720 – 9010 –
1,00 8490 – 9900 –

Shear load FQ (N)

Material Part I (mm) Part II (mm)

1,0 mm 1,5 mm 3,0 mm
x x x

St37 0 63 3210 3410 4060

(375 N/mm2) 0,75 4520 4800 5420
1,00 5040 6410 7090
Shear load: Figures obtained with displa- 1,25 5100 8930 8780
cement of 3 mm between purlin and sheet. 1,50 5130 11280 -

Tensile breaking load Zb (N)

x = 16000

x = arithmetical mean value Shear breaking load Qb (N)

s = Standard deviation

All stated values are x values, representing the arithmetical mean value from laboratory
testing concluded up to now, appropriate safety margins should be applied for field
conditions. Consult also your country’s approval documents. x = 12000
 Technical value May/2006 sre/abjo

TDB-S
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) Pre drill Ø (mm) –x s

S235 2,00 4,90 3880 5
(375 N/mm2) 4,00 5,35 14090 51
TDB-S 5,00 5,65 17590 70
Ø 6,3xL 6,00 5,80 16140 27
8,00 5,80 20660 59
Admission TDB-S
DIBt Z-14.1-4 S355 1,25 5,05 3016 100
(510 N/mm ) 2
1,50 5,35 3419 118
(500 N/mm ) 2
2,00 5,35 5327 162
Material
Fastener:
stainless steel A2, 18/8
Material number 1.4301, AISI 304 Pull-over load Fu (N) Part II

Washer:
stainless steel A2, 18/8
Part I
Material number 1.4301, AISI 304
with vulcanized EPDM Washer S16 Washer S19

Size Material Blechdicke

Head/Drive: Part I (mm) x s x s
Hex., 8 mm A/F S235 (375 N/mm ) 2
0,50 4060 – 5145 –
0,63 5500 – 6560 –
0,75 5920 – 6805 –
0,88 7720 – 9010 –
1,00 8490 – 9900 –

S355 (340N/mm ) 2
0,50 4771 190 -- –
(355N/mm2) 0,63 6029 414 -- –

Shear load FQ (N)

Thickness in mm
– –
Material Part I Part II x s Part II x s
St37 0,75 4570 – 4590 –
(375 N/mm2) 0,88 6520 – 6250 –
1,00 4,0 6740 – 8,0 7280 –
Shear load: Figures obtained with displa- 1,25 11270 – 11220 –
cement of 3 mm between purlin and sheet. 1,50 – – – –

Tensile breaking Shear breaking

load Zb (N) load Qb (N)

x = 16000 x = 12500

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

TDC-S
Pull-out load FZ (N)

Part II (Subconstruction)
TDC-S –
Material Thickness (mm) Pre drill Ø x s
Ø 6,3xL
S355 (530 N/mm )
2
0,4 4,0 580 23
1,0 4,0 2860 100
S355 (530 N/mm )
2
1,5 4,9 4210 100
3,0 4,9 9500 155
Alu PE300 2,0 5,3 2490 140
(230 N/mm2) 3,0 5,3 4780 56
Material 4,0 5,3 6600 107
Fastener: 5,0 5,6 9030 320
stainless steel A2, 18/8 6,0 5,6 12000 280
Material number 1.4301, AISI 304

Washer: Shear load FQ (N)

stainless steel A2, 18/8
Material number 1.4301, AISI 304
with vulcanized EPDM

Size
Head/Drive:
- Hex., 8 mm A/F Thickness in mm
– –
Material Part I Part II x s Part II x s
S235 0,63 3210 – 3410 –
(375 N/mm2) 0,75 4520 – 4800 –
1,00 1,0 5040 – 1,5 6410 –
1,25 5100 – 8930 –
1,50 5130 – 11280 –

0,63 4060 -
0,75 5420 -
1,00 3,0 7090 -
1,25 8780 -
Shear load: Figures obtained with displa-
1,50 *
cement of 3 mm between purlin and sheet.

Tensile breaking load Zb (N)

x = 16000

Shear breaking load Qb (N)

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Februar 2003 sre/abjo

SD2-S

Pull-out load FZ (N)

Teil II (Subconstruction)
–
Material Thickness (mm) x s
St37 0,75 1748 50
(375 N/mm2) 1,00 2255 72

Tensile breaking load Zb (N)

SD2-S
Ø 6,0xL

Material x = 12675
Fastener:
stainless steel A4,
Material number 1.4567, AISI 316

Abmasse
Head / Drive: Shear breaking load Qb (N)
- Hex. , 8 mm A/F

x = 19153

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Juni 2003 sre/abjo

SD2-T

Pull-out load FZ (N)

Teil II (Subconstruction)
–
Material Thickness (mm) xs
St37 0,88 1970 120
(375 N/mm2) 1,50 3800 230
SD2-T
Ø 6,3xL

Pull-over load Fu (N) Part II

Material
Fastener:
Carbon steel with
corrosion protected surface Part I
Washer T15 Washer T19
Washer:
Steel with vulcanized EPDM Material Blechdicke
Part I
Size –x –x
(mm) s s
Head/Drive:
Hex., 8 mm A/F St37 0,50 4950 400 - -
(375 N/mm2) 0,63 5620 350 - -

Shear load FQ (N)

Material Teil 1 (mm) Teil 2 (mm) –x s

St37 0,75 0,75 2983 384

(375 N/mm2) 0,75 1,00 4050 172
0,75 1,25 4709 179
Shear load: Figures obtained with displa-
0,75 2,00 5379 416
cement of 3 mm between purlin and sheet.

Tensile breaking load Zb (N)

x = 22000

Shear breaking load Qb (N)

x = 13500

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value April 2006 sre/abjo

SD3 Ø4,8
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) x s

S235 (375 N/mm2) 1,00 1350 --
1,50 2170 --
2,00 3160 --
3,00 5790 --
SD3 S355 (410 N/mm2) 0,88 1220 69
Ø 4,8xL (520 N/mm2) 1,00 2000 69
(510 N/mm2) 1,50 3323 103
(500 N/mm2) 2,00 5225 167
Material (560 N/mm2) 3,00 9132 150
Fastener:
Carbon steel with
corrosion protected surface
Pull-over load Fu (N) Part II
Washer:
Steel with vulcanized EPDM
Part I
Size
Head/Drive: Washer A14 Washer T15 Washer T19
Hex., 8 mm A/F Material Thickness
–
Part I (mm) x s x– s x s
S235 0,50 -- -- 4950 - 5450 -
(375 N/mm2) 0,63 -- -- 5620 - 6020 -
0,75 -- -- 7100 - 7200 -
0,88 -- -- 7600 - 7800 -
1,00 -- -- 8400 - 8600 -
S355 (570 (N/mm ) 2
0,50 4473 358 3822 431 - -
(390 (N/mm2) 0,63 5861 343 5554 273 - -
(410 (N/mm2) 0,75 -- -- 6760 399 - -
(410 (N/mm2) 0,88 -- -- 8048 237 - -
(375 (N/mm2) 1,00 -- -- 9291 323 - -

Shear load FQ (N)

Material Washer Part I (mm) Part II (mm) x– s

Shear load: Figures obtained with displa-
St37 T15 0,75 2,00 6140 --
cement of 3 mm between purlin and sheet.
(375 N/mm2) T19 1,00 2,00 6980 --

Shear breaking Tensile breaking

load Qb (N) load Zb (N)

x = 13500 x = 22000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

SD3 Ø 5,5-6,3
Pull-out load FZ (N)

Part II (Subconstruction)

Type Ø Material Thickness (mm) x s

5,5 S235 1,50 3750 -
(375 N/mm2) 2,00 5000 -
3,00 7500 -
6,3 S235 0,88 1970 -
(375 N/mm2) 1,00 3330 -
SD3 1,50 5000 -
Ø 5,5xL 2,00 5000 -
Ø 6,3xL 3,00 7500 -
5,5 S355 1,50 3690 112
(510 N/mm2) 2,00 6330 135
Material
(550 N/mm2) 3,00 9922 244
Fastener:
Carbon steel with
corrosion protected surface Pull-over load Fu (N) Part II

Washer:
Steel with vulcanized EPDM
Part I
Size Washer A14 Washer T15 Washer T19
Head/Drive:
Material Thickness
- Hex., 8 mm A/F –
Part I (mm) x s x– s x s
- L12 Head (Ø 12 mm) irius® Drive
S235 0,50 -- -- 4950 - 5450 -
(375 N/mm2) 0,63 -- -- 5620 - 6020 -
0,75 -- -- 7100 - 7200 -
0,88 -- -- 7600 - 7800 -
1,00 -- -- 8400 - 8600 -
S355 (570 (N/mm ) 2
0,40 -- -- 3360 400 - -
(390 (N/mm2) 0,63 -- -- 5620 350 - -
(410 (N/mm2) 0,75 -- -- 7100 460 - -
(410 (N/mm2) 0,88 -- -- 7600 510 - -
1,00 -- -- 8400 590 -- -

Shear load FQ (N)

Ø Material Washer Part I Part II x

(mm) (mm)
4,8 St37 T15 0,75 2,00 6140
(375 N/mm2) T19 1,00 2,00 6980

5,5 St.37 T15 0,63 2,00 3500

(375 N/mm2) T19 1,00 2,00 6800
Shear load: Figures obtained with displa-
cement of 3 mm between purlin and sheet.

Shear breaking Tensile brea

load Qb (N) king load Zb (N)

Ø 5,5 x = 10000 Ø 5,5 x = 16000

Ø 6,3 x = 13500 Ø 6,3 x = 22000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value April/2005 abjo/sre

SD3 - D10
Pull-out load FZ (N)

Part II (Subconstruction)

Material Sheet thickness mm x s

S235 (375 N/mm2) 1,25 2019 146
1,50 2584 154
S235 (360/mm2) 1,50 2791 150

Pull-over load Fu (N) Part II

SD3-D10-T19/C9
Ø 5,5xL Part I

Material Washer Thickness (mm)

S235 (375 N/mm ) 2
x s
1 1

-- 0,62

Material
Fastener:
Carbon steel with
1 = Pull-over load fail in Part II, see Fz value
corrosion protected surface

Washer:
Carbon steel
Shear load FQ (N)
Size
Head/Drive:
- Lens head., 8 mm
- T25
Material Washer Part I Part II x s
(mm) (mm)

Shear load: Figures obtained with displa- S235 (375 N/mm )

2
T19 0,62 1,25 2863 370
cement of 3 mm between purlin and sheet.

Tensile breaking load Zb (N)

x = 16000

Shear breaking load Qb (N)

x = 10000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value April/2006 sre/abjo

SD5
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) x– s

S235 1,50 2650 118
(375 N/mm2) 2,00 3400 170
SD5 SD5-L12 3,00 6300 380
Ø 5,5xL Ø 5,5xL 4,00 9300 650
5,00 11500 920

S355 (510 N/mm ) 2

1,50 2940 173
Material (500 N/mm2) 2,00 4990 342
Fastener: (560 N/mm2) 3,00 9550 516
Carbon steel 18B3 with (520 N/mm2) 4,00 13100 750
corrosion protected surface

Washer: Pull-over load Fu (N) Part II

Carbon steel 18B3
with vulcanized EPDM

Size Part I
Head/Drive: Washer T16 Washer T19
- Hex., 8 mm A/F
- L12 Head (Ø 12 mm) irius® Drive Material Tickness
Part I (mm) x s x s
S235 (375 N/mm ) 0,50
2
4950 400 5450 440
0,63 5620 350 6020 380
0,75 7100 460 7200 470
0,88 7600 510 7800 530
1,00 8400 590 8600 600
Washer T15
S355 (570 N/mm ) 2
0,50 3360 400 -- --
(390 N/mm2)) 0,63 5620 350 -- --
(410 N/mm2)) 0,75 7100 460 -- --
(410 N/mm2)) 0,88 7600 510 -- --
(435 N/mm2)) 1,00 8400 590 -- --

Shear load FQ (N)

Thickness in mm Washer T16

–
Material Part I Part II x s
St37 (375 N/mm ) 2
0,63 2,00 3500 420
0,75 3,00 5400 650
1,00 2,00 6800 820
1,00 3,00 7300 880
1,50 2,00 10600 1270
Shear load: Figures obtained with displa-
1,50 3,00 10800 1300
cement of 3 mm between purlin and sheet.

Shear breaking load

Tensile breaking load
Qb (N)
Zb (N)

x = 15470 x = 10000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value
testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation
conditions. Consult also your country’s approval documents.
 Technical value April/2006 sre/abjo

SD5-H15
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s
S235 (375 N/mm )2
1,50 2795 147
2,00 3987 96
SD5-H15 S355 (510 N/mm )2
1,50 3920 99
Ø 5,5xL (500 N/mm2) 2,00 6180 270
(500 N/mm2) 3,00 10250 400
(520 N/mm2) 4,0 15400 480
Admission SD5-H15
DIBt Z-14.1-4

Material
Pull-over load Fu (N) Part II
Fastener:
Carbon steel 18B3
with corrosion protected surfae Part I
Size
Head/Drive: Material Thickness
Hex., 8 mm A/F Part I
–x
(mm) s
S235 0,63 5732 288
(375 N/mm2) 0,75 7508 515

Shear load FQ (N)

Thickness in mm
Material Part I Part II –x s
St37 0,63 1,50 3179 225
Shear load: Figures obtained with displa- (375 N/mm2) 1,25 3,00 7644 330
cement of 3 mm between purlin and sheet.

Tensile breaking load Zb (N)

x = 15900

Shear breaking load Qb (N)

x = 10000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value March/2006 sre/abjo

SD6
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s
SD6 S235 3,00 6480 320
Ø 6,3xL (375 N/mm2) 4,00 12200 732
5,00 16600 1160
Material 6,00 21000 1680
Fastener:
Carbon steel 18B3 with S355 (560N/mm ) 2
3,00 10800 500
corrosion protected surface (520N/mm2) 4,00 15450 540
(530N/mm2) 5,00 20940 450
Washer: (550N/mm2) 6,00 22720 420
Carbon steel 18B3
with vulcanized EPDM
Pull-over load Fu (N) Part II
Size
Head/Drive:
Hex., 8 mm A/F
Part I
Washer T16 Washer T19

Material Tickness
Part I (mm) x s x s
S235 (375 N/mm ) 0,502
4950 400 5450 440
0,63 5620 350 6020 380
0,75 7100 460 7200 470
0,88 7600 510 7800 530
1,00 8400 590 8600 600
Washer T15
S355 (570 N/mm ) 2
0,50 3360 400 -- --
(390 N/mm2)) 0,63 5620 350 -- --
(410 N/mm2)) 0,75 7100 460 -- --
(410 N/mm2)) 0,88 7600 510 -- --
(435 N/mm2)) 1,00 8400 590 -- --

Shear load FQ (N)

Thickness in mm Washer T16

Material Part I Part II –x s
St37 (375 N/mm ) 2
0,75 6,00 4790 580
0,88 6,00 5300 640
Shear load: Figures obtained with displa- 1,00 6,00 6870 820
cement of 3 mm between purlin and sheet. 1,50 6,00 10760 1290

Shear breaking Tensile brea

load Qb (N) king load Zb (N)

x = 13500 x = 22000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

SD8
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s
S235 2,00 3200 170
(375 N/mm2) 3,00 6200 380
4,00 8800 650
SD8-L12 SD8 6,00 12500 920
Ø 5,5xL Ø 5,5xL
S355 (500 N/mm2) 2,00 4690 240
(560 N/mm2) 3,00 9200 300
(520 N/mm2) 4,00 12240 640
(550 N/mm2) 6,00 15620 1320
Material
Fastener:
Carbon steel 18B3 with Pull-over load Fu (N) Part II
corrosion protected surface

Size
Head/Drive: Part I
Hex., 8 mm A/F
Material Thickness (mm) Washer x– s
S235 (375 N/mm2) 0,50 T15 4950 -
0,63 5620 -
0,75 7100 -
0,88 7600 -
1,00 8400 -
0,50 T19 5450 -
0,63 6020 -
0,75 7200 -
0,88 7800 -
1,00 8600 -
S355 (570 N/mm ) 2
0,40 T15 3490 440
(390 N/mm2) 0,63 5460 380
(410 N/mm2) 0,75 6700 300
(410 N/mm2) 0,88 7710 335
(410 N/mm2) 1,00 9220 130

Shear load FQ (N)

Thickness in mm Washer T15

–
Material Part I Part II x s
St37 0,63 2,00 3300 420
(375 N/mm2) 0,75 3,00 4200 650
1,00 2,00 4400 820
1,00 3,00 5800 880
Shear load: Figures obtained with displa- 1,50 2,00 6200 1270
cement of 3 mm between purlin and sheet. 1,50 3,00 7600 1300

Shear breaking Tensile brea

load Qb (N) king load Zb (N)

x = 12000 x = 15800

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value March/2006 sre/abjo

SD8-H15
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s
S235 2,00 3200 170
(375 N/mm2) 3,00 6200 380
4,00 8800 650
SD8-H15 6,00 12500 920
Ø 5,5xL
S355 (500 N/mm2) 2,00 4690 240
(560 N/mm2) 3,00 9200 300
Admission SD8-H15 (520 N/mm2) 4,00 12240 640
(550 N/mm2) 6,00 15620 1320
DIBt Z-14.1-4

Material
Fastener:
Carbon steel 18B3 with Pull-over load Fu (N) Part II
corrosion protected surface

Size
Part I
Head/Drive:
Hex., 8 mm A/F Material Sheet thickness
Part I (mm) x– s
S235 0,63 3700 320
(375 N/mm2) 0,75 6200 400
0,88 8300 560
1,00 9000 630
S235 0,50 5142 280
(340 N/mm2) 0,63 6544 304

Shear load FQ (N)

Thickness in mm
Material Part I Part II x– s
St37 0,63 2,00 3300 420
(375 N/mm2) 0,75 3,00 4200 650
1,00 2,00 4400 820
1,00 3,00 5800 880
Shear load: Figures obtained with displa- 1,50 2,00 6200 1270
cement of 3 mm between purlin and sheet. 1,50 3,00 7600 1300

Shear breaking Tensile breaking

load Qb (N) load Zb (N)

x = 12000 x = 15800

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value March/2006 sre/abjo

SD14
Pull-out load FZ (N)

Part II (support)
–
Material Thickness (mm) x s
S235 4,00 8959 726
(375 N/mm2) 5,00 10914 1299
8,00 12040 -
10,00 12040 -

SD14 S355 (520 N/mm2) 4,00 12150 380

Ø 5,5xL (530 N/mm2) 5,00 16000 310
(550 N/mm2) 6,00 16900 480
(460 N/mm2) 8,00 16700 460
Material
Fastener:
Carbon steel 18B3 Pull-over load Fu (N) Part II

Washer:
Carbon steel 18B3 Part I
with vulcanizedEPDM
Washer T16 Washer T19
Size
Material Thickness
Head/ Drive:
Part I(mm) x– s x– s
Hex., 8 mm A/F
S235 0,50 4950 400 5450 440
(375 N/mm2) 0,63 5620 350 6020 380
0,75 7100 460 7200 470
0,88 7600 510 7800 530
1,00 8400 590 8600 600
Washer T15
S355 (570 N/mm ) 2
0,40 3490 440 -- --
(390 N/mm2) 0,63 5460 380 -- --
(410 N/mm2) 0,75 6700 300 -- --
(410 N/mm2) 0,88 7710 335 -- --
(410 N/mm2) 1,00 9220 130 -- --

Shear load FQ (N)

Shear load: Figures obtained with dis- Thickness in mm Washer T16

placement of 3 mm between purlin and –
Material Part I Part II x s
sheet.
St37 (375 N/mm2) 0,63 2,00 3300 420
0,75 3,00 4200 650
1,00 2,00 4400 820
1,00 3,00 5800 880
1,50 2,00 6200 1270
1,50 3,00 7600 1300

Shear breaking load Qb (N) Tensile breaking load Zb (N)

x = 9826 x = 12040

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

SD14 - H15
Pull-out load FZ (N)

Part II (support)
–
Material Thickness (mm) x s
St37 4,00 8959 726
SD14-H15 (375 N/mm2) 5,00 10914 1299
Ø 5,5xL 6,00 12040 ---
8,00 12040 ---
Material
S355 (520 N/mm2) 4,00 12150 380
Fastener:
(530 N/mm2) 5,00 16000 310
Carbon steel 18B3
(550 N/mm2) 6,00 16900 480
(460 N/mm2) 8,00 16700 460
Size
Head/ Drive:
Hex., 8 mm A/F

Shear load FQ (N)

Thickness in mm
–
Material Part I Part II x s
St37 (375 N/mm )
2
0,63 4,00 4293 412
Shear load: Figures obtained with dis-
0,75 5,00 5374 411
placement of 3 mm between purlin and
0,88 5,00 6632 512
sheet.

Tensile breaking load Zb (N)

x = 12040

Shear breaking load Qb (N)

x = 9826

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value September/2004 sre/pko

SDC2-L12

Pull-out load FZ (N)

Part II (support) Thickness in mm Washer A 16

–
Material Part I Part II x s
St37 (375 N/mm )
2
0,63 0,63 2225 84
0,75 0,75 2648 129
0,88 0,88 2929 108
1,00 1,00 3060 141
SDC2-L12 1,25 1,25 4831 255
Ø 5,5xL

Material
Fastener:
Carbon steel 18B3, with Pull over load Fu (N) Part II
corrosion protected surface

Washer: Part I
Carbon steel 18B3
with vulcanizedEPDM Washer A16

Material Sheet thickness Part I (mm) x s

Size
Head/ Drive: St37 0,63 3374 182
- L12 Head (Ø 12 mm) irius® Drive (375 N/mm2) 0,75 4317 263
0,88 4539 184

Tensile breaking load Zb (N)

x = 16000

Shear breaking load Qb (N)

x = 10000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SDL3

Pull-out load FZ (N)

Part II (support) Thickness in mm Washer T15

–
Material Part I Part II x s
St37 (375 N/mm )
2
0,50 0,55 934 -
0,75 1,25 2783 -
0,75 0,75 1525 -
0,75 1,50 3566 -
SDL3-L12
Ø 5,5xL

Material
Fastener:
Pull-over load Fu (N) Part II
Carbon steel 18B3 with
corrosion protected surface
Part I
Washer:
Carbon steel 18B3 Washer T15
with vulcanizedEPDM Material Blechdicke Teil I (mm) x s

Size St37 0,50 4950 -

Head/ Drive: (375 N/mm2) 0,63 5620 -
- L12 Head (Ø 12 mm) irius® Drive 0,75 7100 -
0,88 7600 -
1,00 8400 -

Tensile breaking load Zb (N)

x = 16000

Shear breaking load Qb (N)

x = 10000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value March 2006 pko/sre

SDT5
Pull-out load FZ (N)

Part II (support) Thickness in mm Washer A19

–
Material x s
S235 (375 N/mm ) 2
1,50 2800 170
(355 N/mm2) 2,00 4120 165
(375 N/mm2) 3,00 6300 380
(375 N/mm2) 4,00 9300 650
S355 (510 N/mm2) 1,50 3313 150
S355 (500 N/mm2) 2,00 5280 200
SDT5 S355 (560 N/mm2) 3,00 10140 600
Ø 5,5xL S355 (520 N/mm2) 4,00 14200 420

Material
Pull-over load Fu (N) Part II
Fastener:
Carbon steel 18B3 with
corrosion protected surface
Part I
Washer:
Carbon steel 18B3 Washer A19
with vulcanizedEPDM –
Material Thickness Part I (mm) x s
Size S355 (570 N/mm ) 2
0,40 4890 490
Head/ Drive: (390 N/mm2) 0,63 5650 500
Hex., 8 mm A/F S320 (410 N/mm ) 2
0,75 7100 670
Washer S19

S355 (570 N/mm2) 0,40 4790 790

(390 N/mm2) 0,63 6090 690
S320 (410 N/mm2) 0,75 8540 550

Deflection gem. ECCS °

Panel thickness (mm) SDT5 / SDTP5 Deflection a (mm)

40 2,5
S235 (375 N/mm ) 2
50 3,0
60 3,6
70 4,3
90 5,5

Shear breaking Tensile breaking

load Qb (N) load Zb (N)

x = 10000 x = 16000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value March 2006 pko/sre

SDT14
Pull-out load FZ (N)

Part II (support) Thickness in mm Washer A19

–
Material x s
S235 (375 N/mm ) 2
4,00 10170 670
S235 (375 N/mm ) 2
5,00 10820 910
S235 (375 N/mm ) 2
8,00 11150 540

S355 (520 N/mm2) 4,00 9939 743

S355 (530 N/mm2) 5,00 10958 758
S355 (550 N/mm2) 6,00 10958 758.

SDT14
Ø 5,5xL Pull-over load Fu (N) Part II

Material
Part I
Fastener:
Carbon steel 18B3 with
corrosion protected surface Washer A19
–
Material Thickness Part I (mm) x s
Washer:
Carbon steel 18B3 S355 (570 N/mm ) 2
0,40 4900 370
with vulcanizedEPDM (390 N/mm2) 0,63 5680 250
Washer S19
Size
Head/ Drive: S355 (570 N/mm2) 0,40 5100 470
Hex., 8 mm A/F (390 N/mm2) 0,63 6480 520

Deflection gem. ECCS

°

Panel thickness (mm) SDT14 / SDTP14 Deflection a (mm)

I-Purlin / 10 mm 40 2,5
S235 (375 N/mm ) 2
50 3,0
60 3,6
70 4,3
90 5,5

Shear breaking Tensile breaking

load Qb (N) load Zb (N)

x = 10000 x = 16000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Februar 2003 abjo/sre

SDP3

Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s
St52 (530 N/mm )
2
1,50 4028 236
SDP-3 2,00 6270 372
Ø 5,5xL 2,50 8363 185
3,00 10430 477

Material
Fastener:
Carbon steel 18B3
with corrosion protected surfae
Tensile breaking load Zb (N)

Size
Head/Drive:
Hex. (WH11), 11 mm A/F
x = 16000

Shear breaking load Qb (N)

x = 10000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value August 2003 abjo/sre

SDP6
Pull-over load Fu (N) Part II

Part I

Flange Ø 10 mm
–
Material Thickness Part I (mm) x s
St37 (375 N/mm )
2
0,50 3092 83
SDP-6 0,63 4047 88
Ø 5,5xL 0,75 5039 159
0,88 5709 196
1,00 6331 118

Material
Tensile breaking load Zb (N)
Fastener:
Carbon steel 18B3 with
corrosion protected surface

Washer:
Aluminium
with vulcanizedEPDM x = 16000

Size
Head/ Drive:
Hex., 8 mm A/F
Shear breaking load Qb (N)

x = 10000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Februar 2003 abjo/sre

SDTW

Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Embedment (mm) x s
Timber wood 35 3141 743

SDTW Pull-over load Fu (N) Part II

Ø 6,5xL

Part I
Material Washer A19
Fastener:
Carbon steel 18B3 with Material Thickness (mm) x s
korrosionsgeschüzter Oberfläche St37 0,50 2140 -
(375 N/mm2) 0,63 5000 -
Washer: 0,75 6200 -
Aluminium
with aufvulkanisiertem EPDM

Size
Head/ Drive: Tensile breaking load Zb (N)
Hex., 8 mm A/F

x = 20000

Shear breaking load Q (N)

b

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value März/2003 sre/abjo

SW-T
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Embedment x s
Ø 4,8 Wood 20 mm 1700 445
25 mm 2030 280
30 mm 2260 150
Ø 6,5 Wood 20 mm 1900 120
25 mm 2300 140
SW-T 30 mm 3000 180
Ø 4,8xL 45 mm 4810 245
Ø 6,5xL
Pull-over load Fu (N) Part II
Material
Fastener:
Carbon steel 18B3 Part I

Washer: Washer A14

Aluminium Material Blechdicke
with vulcanized EPDM Part I
–
(mm) x s
Size
Head/Drive: Ø 4,8 St37 (375 N/mm )
2
0,50 2260 150
Hex., 8 mm A/F 0,70 2260 150

Ø 6,5 St37 (375 N/mm )

2
0,50 3000 110
0,75 3000 110
Diese Werte wurden bei voll eingeschraubten Befestigern ermittelt. Die Pull-out load F sind
z
zu berücksichtigen.

Shear load FQ (N) Part II

Part I

Thickness in mm Washer A14

Material/Part II Part I x– s
Ø 4,8 St37/Wood 0,50 1530 75
Shear load: Figures obtained with dis- (375 N/mm2) 0,75 1600 135
placement of 3 mm between purlin and Ø 6,5 St37/Wood 0,50 1860 170
sheet. (375 N/mm2) 0,75 1690 220

Tensile breaking load Z (N)

b

Ø 4,8 x = 10700
Ø 6,5 x = 21500

Shear breaking load Qb (N)

Ø 4,8 x = 6700
Ø 6,5 x = 12800
All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value
testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation
conditions. Consult also your country’s approval documents.
 Technical value März/2003 sre/abjo

SL2-T
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s

SL2-T St37 (375 N/mm ) 2

2x0,63 1180 60
2x0,75 1310 64
Ø 4,8xL
Alu PE 300 2x1,00 2360 49
Admission SL2-T
DIBt Z-14.1-4 Alu F 25 2x0,6 610 45
2x0,70 820 45
Material
Fastener:
Carbon steel 18B3 Shear load FQ (N)
Size
Head/Drive:
Hex., 8 mm A/F

Thickness in mm
Material Part I Part II –x s
Shear load: Figures obtained with dis-
St37 (375 N/mm )
2
0,63 0,63 1820 210
placement of 3 mm between purlin and
sheet. Alu PE 300 1,00 1,00 1950 88

Tensile breaking load Z (N)

b

x = 10000

Shear breaking load Qb (N)

x = 6300

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

SL2-H15
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s

SL2-H15 S235 (375 N/mm ) 2

2x0,75 1360 -
2x1,00 1990 -
Ø 6,3xL
S355 (490 N/mm )
2
2x0,75 1689 119
Admission SL2-H15 (520 N/mm2) 2x1,00 2579 120
DIBt Z-14.1-4

Material
Fastener:
Carbon steel 18B3 Shear load FQ (N)
Size
Head/Drive:
Hex., 8 mm A/F

Thickness in mm
–
Material Part I Part II x s
Shear load: Figures obtained with dis-
S235 (375 N/mm )2
0,75 0,75 3380 -
placement of 3 mm between purlin and
1,00 1,00 4800 -
sheet.

Tensile breaking load Z (N)

b

x = 20000

Shear breaking load Q (N)

b

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value June/2006 sre/abjo

SL3-H15

Pull-out load FZ (N)

Thickness in mm
SL3-H15 –
Material Part I Part II x s
Ø 6,3xL
S235 (375 N/mm )
2
0,75 1,25 1986 89
0,75 1,50 2896 80
Material
1,50 1,50 3200 190
Fastener:
S355 (510 N/mm )
2
1,25 1,25 2874 250
Carbon steel 18B3
1,50 1,50 3873 297
Washer:
without

Size
Head/Drive: Shear load FQ (N)
Hex., 8 mm A/F
Part II

Part I

Thickness in mm
–
Material Part I Part II x s
S235 (375 N/mm ) 2
0,75 1,25 2651 215
0,75 1,50 2957 109
Shear load: Figures obtained with dis- 0,88 1,25 2898 124
placement of 3 mm between purlin and 0,88 1,50 3228 157
sheet. 1,50 1,50 6900 830

Tensile breaking load Z (N)

b

x = 20000

Shear breaking load Q (N)

b

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May 2005 sre/abjo

SL2-S-4,8x22

Pull-out load FZ (N)

Part II (Subconstruction)
SL2-S
Material Thickness (mm) x– s
Ø 4,8x22
St37 (290 N/mm ) 2
0,40 525 22
2x0,50 682 27
2x0,63 1015 71
2x0,75 1171 61
2X1,00 1687 57

Material Alu (265 N/mm )

2
2x0,75 548 148
Fastener:
stainless steel A2, 18/8
Material number, AISI 304

Washer:
stainless steel A2, 18/8
Material number, AISI 304, Shear load FQ (N)
with vulcanized EPDM
Shear load: Figures obtained with displa-
und
cement of 3 mm between purlin and sheet.
Aluminium
with vulcanized EPDM

Size
Head/Drive: Material Part I Part II –x s
Hex., 8 mm A/F St37 (375 N/mm )
2
0,63 0,63 1524 64

Tensile breaking load Zb (N)

x = 9800

Shear breaking load Qb (N)

x = 5900

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SL3-F
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness in mm
St. 37 x
SL3-F Part I
Ø 4,2x15 St. 37 (375 N/mm )
2
0,7 1,0 1,2 1,5 2,0

0,7 mm 830 1100 1100 1100 1500

1,0 mm 550 550 550 550 -

Material 1,2 mm 550 550 550 550 -

Fastener:
Carbon steel 18B3
Oberfläche:
gelb zinced Shear load FQ (N)
Size
Head/Drive:
- Vierkant, Schlüsselweite 6 mm
Part II Thickness in mm
St. 37 x
Part I
St. 37 (375 N/mm )
2
0,7 1,0 1,2 1,5 2,0

0,7 mm 2100 2600 2950 3400 4200

1,0 mm 2600 3100 3400 3850 -

Shear load: Figures obtained with dis-
placement of 3 mm between purlin and
1,2 mm 2950 3400 3700 4200 -
sheet.

Tensile breaking load Z (N)

b

x = 6730

Shear breaking load Q (N)

b

x = 5140

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SL4-F
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness in mm
St. 37 x
Part I
SL4-F
St. 37 (375 N/mm )
2
0,7 1,0 1,2 1,5 2,0
Ø 4,8x16
1,0 mm - - - - 2700
Material
Fastener:
1,2 mm - - - 2200 2200
Carbon steel 18B3
Surface:
blue zinced
1,5 mm NA NA 1900 1900 1900

2,0 mm 800 1000 1000 1000 1000

Size
Head/Drive: NA = not applicably
- Square, 6 mm A/F

Shear load FQ (N)

Part II Thickness in mm
St. 37 x
Part I
St. 37 (375 N/mm )
2
0,7 1,0 1,2 1,5 2,0

1,0 mm - - - - 4650

1,2 mm - - - 4200 4960

1,5 mm NA NA 4200 4960 5430

Shear load: Figures obtained with dis-
placement of 3 mm between purlin and 2,0 mm 4200 4650 4960 5430 6200
sheet.
NA = not applicably

Tensile breaking load Z (N)

b

x = 6730

Shear breaking load Q (N)

b

x = 7770

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

TDA-T

Pull-out load FZ (N)

Part II (Subconstruction)

Material Sheet thickness (mm) Pre drill Ø

– –
Embedment (mm) (mm) x s x s
TDA-T Alu 3,0 4,50 3400 52 – –
Ø 6,5xL
St37 0,75 4,50 1091 33 - -
(375 N/mm2) 1,50 4,50 2745 81 - -
4,50 4,50 2290 - - -
1,50 5,05
Material 2,00 5,05 - - 5400 -
Fastener: 2,50 5,05 - - 7920 -
Carbon steel 18B3 3,00 5,05 - - 9750 -
with korrosionsgescützter Oberfläche Wood 25 4,80 – - 2320
30 4,8 – – 3360 –
Washer: 40 4,80 - - 4170 -
Carbon steel 18B3
50 4,80 - - 5720 -
with vulcanized EPDM

Size
Head/Drive:
Hex., 8 mm A/F Pull-over load Fu (N) Part II

Part I
Washer S16 Washer S19

Material Part I
(mm) x– s x– s
S235 (375 N/mm ) 2
0,50 4060 – 5145 –
0,63 5500 – 6560 –
0,75 5920 – 6805 –
0,88 7720 – 9010 –
1,00 8490 – 9900 –

S355 (340 N/mm )2

0,50 4771 190 -- –
(355 N/mm2) 0,63 6029 414 -- –

Tensile breaking load Z (N)

b

x = 16000

Shear breaking load Q (N)

b

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value
testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation
conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

TDA-T
Shear load FQ (N)

Material Part I Part II –x s

(mm) (mm)
St37 (375 N/mm )
2
0,63 1,00 3210 -
1,50 3410 -
3,00 4060 -
0,75 1,00 4520 -
1,50 4800 -
3,00 5420 -
1,00 1,00 5040 -
1,50 6410 -
3,00 7090 -
1,25 1,00 5100 -
1,50 8930 -
Shear load: Figures obtained with dis- 3,00 8780 -
placement of 3 mm between purlin and 1,50 1,00 5130 -
sheet. 1,50 11280 -

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/ 2006 sre/abjo

TDB-T/TDC-T
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) Pre drill Ø x s
S235 2,00 5,35 5200 –
(375 N/mm2) 2,50 5,35 7530 –
TDB-T 4,00 5,65 12050 –
Ø 6,3xL 5,00 5,65 15642 –
6,00 5,65 17310 –
8,00 5,80 20424 –
S355 1,25 5,05 3016 100
(510 N/mm ) 2
1,50 5,35 3419 118
Material (500 N/mm ) 2
2,00 5,35 5327 162
Fastener:
Carbon steel 18B3 with
corrosion protected surface
Pull-over load Fu (N) Part II
Washer:
Carbon steel 18B3
with vulcanized EPDM Part I

Size Washer S16 Washer S19

Head/Drive:
Material Thickness
- Hex., 8 mm A/F
Part I
– –
(mm) x s x s
St37 0,50 4060 – 5145 –
(375 N/mm2) 0,63 5500 – 6560 –
0,75 5920 – 6805 –
0,88 7720 – 9010 –
1,00 8490 – 9900 –
S355
(340N/mm2) 0,50 4771 190 -- –
(355N/mm2) 0,63 6029 414 -- –

Shear load FQ (N)

Thickness in mm
Material Part I Part II –x s
St37 (375 N/mm ) 2
0,75 4,00 4570 –
8,00 4590 –
0,88 4,00 6520 –
8,00 6250 –
1,00 4,00 6740 –
Shear load: Figures obtained with dis-
8,00 7280 –
placement of 3 mm between purlin and
1,25 4,00 11270 –
sheet.
8,00 11220 –

Shear breaking Tensile breaking

load Qb (N) load Zb (N)

x = 13000 x = 21000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May / 2006 sre/hch

TDBL

Pull-out load FZ (N)

TDBL Part II (Subconstruction)

Ø 8,6xL –
Material Thickness mm Pre drill mm x s
steel S355 0,90 Ø 7,5 1440 76
1,00 6,5x10,5 2750 60
1,25 Ø 7,5 5160 150
Material
Fastener: steel S235 10,00 Ø 8,0 29400 1000
Carbon steel , material number 17B2
DIN 1.5502

Size
Head/Drive:
- Hex., 13 mm A/F Shear load FQ (N)
Part II

Part I

Thickness in mm
–
Material Part I Part II Pre-drill mm x s
steel S355 0,90 0,90 Ø 7,5 3400 290
Shear load: Figures obtained with displace-
1,00 1,00 Ø 7,5 4500 290
ment of 3 mm between purlin and sheet.
2,00 2,00 Ø 7,5 15600 390

Shear breaking load Qb (N)

x = > 26000

Product information
Hole size:
- Components t < 1,25 mm in steel S235 or S355, pre-drilled with Ø 7,5 mm or 6,5 x 10,5 mm slot
- Components t < 3 mm, pre-drilled with Ø 7,5 mm
- Components t ≥ 3 mm,pre-drilled with Ø 8,0 mm

x = arithmetical mean value All stated values are x values, representing the arithmetical mean value from laboratory
s = Standard deviation testing concluded up to now, appropriate safety margins should be applied for field
conditions. Consult also your country’s approval documents.
 Technical value May 2005 sre/abjo

SDK-S
Pull-out load FZ (N)

Part II (Subconstruction)

Type Material Thickness (mm) –x / Klip with 2 Fastener s

SDK2-S St37 0,63 1327 37
(375 N/mm2) 0,75 3740 327
1,00 5290 317
1,25 6730 327
Alu 0,90 2210 209
1,20 3480 213
1,80 5610 144
SDK2 SDK3
Ø 6,0xL Ø 6,0xL

Type Material Thickness (mm) x– / Klip with 2 Fastener s

Certified in the perm9issions the crease
roofs manufacturer SDK3-S St37 1,50 6070 295
(375 N/mm2) 1,75 6770 197
Material 2,00 7840 145
Fastener: 2,50 9370 380
stainless steel A2, 18/8 3,00 11650 495
Alu 1,80 5100 180
Size
2,00 6052 360
Head/Drive:
2,50 8300 220
Special square
3,00 10880 260

Tensile breaking load Z (N)

b

x = 11000

Shear breaking load Q (N)

b

x = 7500

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SXW
Pull-out load FZ (N)

Part II (Subconstruction)

Material Embedment (mm) –x s

20 1760 190
Wood 25 2170 300
30 2570 200

Pull-over load Fu (N) Part II

SXW SXW-L12
Ø 6,5xL Ø 6,5xL
Part I
Washer S16
Admission SXW
Material Thickness
DIBt Z-14.1-4 Part I
–x
(mm) s
Material St 37 0,50 4000 –
Fastener: (375 N/mm2) 0,75 6200 –
stainless steel 1.4301 0,88 7500 –

Washer: Alu 0,50 1500 –

stainless steel 1.4301 0,75 2700 –
with vulcanized EPDM 0,88 3100 –

Size
Head/Drive:
Shear load FQ (N)
Hex., 8 mm A/F

Thickness in mm Washer S16

Material Part I Part II –x s
St37 (375 N/mm )2
0,50 1870 130
Wood 0,75 2280 250
0,87 2580 370
Shear load: Figures obtained with dis-
placement of 3 mm between purlin and Aluminium (230 N/mm ) 2
0,50 880 78
sheet. Wood 0,77 1500 85

Tensile breaking load Z (N)

b

x = 16000

Shear breaking load Q (N)

b

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value August/2003 sre/hch

RV6604
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s Pre drill Ø mm
Alu PE300 1/2h 1,00 1674 47
Alu PE300 1/2h 1,25 1906 34 5.35
Alu 1,80 2060 25

Admission RV6604 St37 (375 N/mm ) 2

0,50 1362 28
DIBt Z-14.1-4 0,75 1990 55 5,35
1,20 2140 80
Material
Sleeve:
AIMg5
Mandrel:
AICuMg1

Size
Shear load FQ (N) FQ
Shank:
Ø 5,2 mm
Mandrel:
FQ
Ø 2,8 mm
Bund:
Ø 11,5 mm Thickness in mm
Material Part I Part II –x s
Shear load: Figures obtained with Aluminium (230 N/mm )
2
1,80 1,80 3020 235
displacement of 3 mm between purlin
and sheet. St37 (375 N/mm )
2
0,75 0,75 2050 44

Tensile breaking load Z (N)

b

x = 2050

Shear breaking load Q (N)

b

x = 3300

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value August/2003 sre/hch

RV6603
Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s Pre drill Ø mm
Alu 0,70 2300 - 7,90

St37 (375 N/mm )

2
0,55 3120 - 7,90

Material
Sleeve:
AIMg5
Mandrel:
AICuMg1

Size
Shank:
Ø 7,8 mm
Mandrel:
Ø 4,4 mm
Bund:
Ø 15,7 mm

Tensile breaking load Z (N)

b

x = 5000

Shear breaking load Q (N)

b

x = 6800

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SXC
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) –x s

St37 (375 N/mm ) 2
1,5 2300 85
2,0 4000 150
3,0 7200 185
4,0 10280 1035

Pull-over load Fu (N) Part II

Part I

Washer S16 Washer S19 Washer S22

SXC5
Ø 5,5xL Material Blechdicke
Part I
– – –
(mm) x s x s x s
Admission SXC5
St37 0,50 4100 495 4200 500 3900 255
DIBt Z-14.4-407
(375 N/mm2) 0,62 4800 345 5100 655 5100 265
0,75 6300 540 7000 865 – –
Material
0,87 6600 530 7100 735 – –
Fastener:
stainless steel A2, 18/8 Alu 0,50 1400 185 1300 125 1400 140
Material number 1.4301, AISI 304 (230 N/mm2) 0,65 1900 175 1900 260 1900 185
0,70 2400 240 2100 240 2200 225
Washer: 0,80 2400 240 2700 310 – –
stainless steel A2, 18/8 1,00 – – 3300 290 3500 315
Material number 1.4301, AISI 304
with vulcanized EPDM
Max. deflection (mm)
Size
Head/Drive:
- Hex., 8 mm A/F
- L12 Head (Ø 12 mm) irius® Drive
Panelendicke (mm) 1,5 mm ≤ t ≤ 4 mm
Material a (mm)
St37 (375 N/mm )2
40 4
60 6
80 8

Tensile breaking load Z (N)

b

x = 17500

Shear breaking load Q (N)

b

x = 10900

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SXCW
Pull-out load FZ (N)

Part II (Subconstruction)

Material Embedment (mm) –x s

Timber 50 5800 585
Leimbinder 50 6500 325

Pull-over load Fu (N) Part II

Part I
SXCW Washer S16 Washer S19 Washer S22
Ø 6,5xL
Material Blechdicke
Admission SXCW Part I
x– x– –x
DIBt Z-14.4-407 (mm) s s s
St37 0,50 4100 280 4200 280 4100 560
Material
(375 N/mm2) 0,62 5100 225 5700 510 6400 650
Fastener:
Alu 0,50 1300 120 1200 100 1000 180
stainless steel A2, 18/8
(230 N/mm2) 0,62 1600 300 1400 95 1300 170
Material number, AISI 304

Washer:
stainless steel A2, 18/8
Material number 1.4301, AISI 304
with vulcanized EPDM
Tensile breaking load Zb (N)

Size
Head/Drive:
- Hex., 8 mm A/F
- L12 Head (Ø 12 mm) irius® Drive x = 17500

Shear breaking load Qb (N)

x = 10900

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value November/2005 sre/abjo

SCFW

Pull-out load FZ (N)

Part II (Subconstruction)
–
Type Material Embedment (mm) x s
SCFW Timber 38 2700 -
45 3830 –
49 4500 -
53 5700 --

Tensile breaking load Z (N)

b

x = 21150
SCFW
Ø 6,5xL

Admission SCFW Shear breaking load Q (N)

DIBt Z-31.1-47, 31.1-137 b
Z-31.1-52, 31.1-142
Z-31.1-128, 31.1-130

Material
Fastener: x = 11000
SCFW: Carbon steel, hot dip galvanised
SCFW-S: Material number 1.4301, AISI 304

Washer: BAZ
stainless steel A2
with vulcanisedEPDM

Size
Head/Drive:
Hex., 8 mm A/F

Washer:
BAZ Ø 25 mm

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SCFW-S

Pull-out load FZ (N)

Part II (Subconstruction)

Type Material Embedment (mm) –x s

SCFW-S Timber 30 1790 145

SCFW Tensile breaking load Zb (N)

Ø 5,0xL

Material
Fastener:
SCFW-S: stainless steel A2 x = 7000
Material number 1.4301, AISI 304

Washer: A12
Aluminium
with vulcanisedEPDM Shear breaking load Qb (N)
Size
Head: Ø10 mm
Drive: T20W

Washer: x = 5000
A12 Ø12 mm

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SCF3/SCF12

Pull-out load FZ (N)

Part II (Subconstruction)

Type Material Thickness (mm) –x s

SCF3 St37 1,5 3120 125
(375 N/mm2) 3,0 6300 340
SCF12 St37 3,0 6220 440
(375 N/mm2)

Tensile breaking load Zb (N)

x = 21150

SCF3 SCF12
Ø 6,3xL Ø 6,3xL
Shear breaking load Qb (N)
Material
Fastener:
Carbon steel 18B3

Washer: BAZ x = 11000

stainless steel A2
with vulcanised EPDM

Size
Head/Drive: Hex.,
8 mm A/F

Washer:
BAZ Ø 25 mm

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

TT/TTN

Pull-out load FZ (N)

Part II (Subconstruction)

Material Embedment (mm) –x s

TTN-A-D16 4,0 4600 400

6,0 8800 450

TT TTN

Test certificate ETB

Material
Fastener: Tensile breaking load Zb (N)
stainless steel A2
Material number 1.4301

Washer:
stainless steel with x = 10200
aufvulkanisiertem EPDM

Sleeve TTN:
AlMg5
Shear breaking load Qb (N)
Size
Schraube: TT-S-D12-5xL
Head: Ø 12
Innenangriff: T20

Washer: x = 6290
Sleeve TTN-A-D16
Ø 16 mm

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2004 sre/abjo

ASO
Pull-out load FZ (N)

Fz

Part II (Subconstruction)
–
Type Material Thickness (mm) x s Pre drill- Ø mm
ASO St37 (375 N/mm2) 0,75 1260 56
4,9
Ø 4,8 mm

ASO Shear load FQ (N) FQ

Ø 4,8xL

Material
Sleeve: FQ
Aluminium AlMg3
Thickness in mm
Mandrel:
stainless steel A3 Type Material Part I Part II x– s
Material number 1.4541 ASO Alu (230 N/mm )2
1,8 1,8 2020 40
Ø 4,8 mm
Size St37 (375 N/mm ) 2
0,75 0,75 2337 162
Shank: 0,75 3,0 1820 60
Ø 4,0/4,8 mm
Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.
Head:
Ø 8,0/9,5 mm

Tensile breaking load Zb (N) Z

Zb
b

Ø 4,0 x = 1420
Ø 4,8 x = 1950

Shear breaking load Qb (N) Qb

Qb
Ø 4,0 x = 1120
Ø 4,8 x = 1480

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2004 sre/hch

ASO-D11/D14
Pull-out load FZ (N)

Fz

Part II (Subconstruction)
–
Type Material Thickness (mm) x s Pre drill- Ø mm
ASO St37 (375 N/mm2)
5,1

ASO
Ø 5,0xL

Shear load FQ (N) FQ

Material
Sleeve:
Aluminium AlMg3

Mandrel: FQ
stainless steel A3
Material number 1.4541 Thickness in mm
–
Size Type Material Part I Part II x s
Shank:
Ø 5,0 mm

Head: Shear load Figures obtained with displacement of 3 mm Part I und

Ø 11/14 mm Part II

Tensile breaking load Zb (N) Z

Zb
b

x = 2500

Shear breaking load Qb (N) Qb

Qb
x = 1650

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

ASC
Pull-out load FZ (N)

Fz

Part II (Subconstruction)

Type Material Thickness (mm) x– s Pre drill-Ø mm

ASC Alu (230 N/mm )
2
1,80 2350 120
Ø 4,8 m
Alu (230 N/mm2) 3,00 3020 125
4,9
ASC St37 (375 N/mm ) 2
0,75 1130 80
ASC Ø 4,8 mm
Ø 4,8xL 1,20 2170 105

Admission ASC
DIBt Z-14.1-4
Shear load FQ (N) FQ
Material
Sleeve:
AlMg5
Mandrel: FQ
stainless steel A3
Material number 1.4541
Thickness in mm
Size Type Material Part I Part II x– s
Shank:
ASC Alu 1,8 4,00 2700 85
Ø 4,8 mm
Ø 4,8 mm
Head: (230 N/mm2)
Ø 9,5 mm
ASC St37 0,75 5,00 2650 85
Shear load: Figures obtained with dis-
Ø 4,8 mm
placement of 3 mm between purlin and (375 N/mm2)
sheet.

Tensile breaking load Zb (N)

Z
b Zb

Ø 4,8 x = 3400

Shear breaking load Qb (N) Qb

Qb
Ø 4,8 x = 2400

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May/2006 sre/abjo

AAC

AAC
Ø 4,8xL

Material
Sleeve:
EN AW-1050 A
Mandrel:
Al

Size
Shank:
Ø 4,8 mm
Head:
Ø 9,5 mm
Mandrel:
Ø 2,7 mm
Predrill:
Ø 4,9 mm

Tensile breaking load Zb (N)

Z
b Zb

1400

Shear breaking load Qb (N) Qb

Qb
1000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2004 sre/abjo

ATO

Pull-out load FZ (N)

Fz

Part II (Subconstruction)
–
Type Material Thickness (mm) x s Pre drill-Ø (mm)

ATO Ø 4,8 mm Alu (230 N/mm ) 2

1,80 2140 55 4,9

ATO
Ø 4,8xL

Material
Sleeve:
ATO – AIMg3
Mandrel: Shear load FQ(N) FQ
ATO – Carbon steel zinced

Size
Shank:
Ø 4,8 mm FQ
Head:
Ø 9,5 mm Thickness in mm
–
Type Material Part I Part II x s
ATO Alu 1,80 4,00 1950 85
Shear load: Figures obtained with dis- Ø 4,8 mm (230 N/mm2)
placement of 3 mm between purlin and St37 0,75 4,00 1820 65
sheet. (315 N/mm2)

Tensile breaking load Zb (N)

Z
b Zb

Ø 4,8 mm x = 1950
Ø 5,0 mm x = 2955

Shear breaking load Qb (N) Qb

Qb
Ø 4,8 mm x = 1480
Ø 5,0 mm x = 1858

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

ATC
Pull-out load FZ (N)

Fz

Part II (Subconstruction)
–
Type Material Thickness (mm) x s Pre drill-Ø (mm)
ATC Alu (230 N/mm2) 1,80 1340 95 3,3
Ø 3,2 mm
Alu (230 N/mm2) 3,00 1335 140 3,3
ATC Alu (230 N/mm2) ,80 2010 70 4,1
Ø 4,0 mm
Alu (230 N/mm2) 3,00 2250 130 4,1
ATC ATC Alu (230 N/mm2) 1,80 2510 85 4,9
Ø div.xL Ø 4,8 mm
Alu (230 N/mm )
2
3,00 3250 190 4,9
ATC St37 (375 N/mm )2
0,75 880 35 3,3
Admission ATC (only Ø 4,8 mm)
Ø 3,2 mm
DIBt Z-14.1-4 St37 (375 N/mm )2
1,20 1300 52 3,3

Material ATC St37 (375 N/mm ) 2

0,75 1050 55 4,1
Sleeve: Ø 4,0 mm
St37 (375 N/mm ) 2
1,20 1850 85 4,1
Aluminium AIMg5
Mandrel: ATC St37 (375 N/mm ) 2
0,75 1240 70 4,9
Carbon steel Ø 4,8 mm
St37 (375 N/mm ) 2
1,20 2330 190 4,9

Size
Shank: Shear load FQ(N) FQ
Ø 3,2/4,0/4,8 mm
Head:
Ø 6,5/8,0/9,5 mm FQ

Thickness in mm
–
Type Material Part I Part II x s
ATC St37 0,75 3,00 1300 85
Ø 3,2 mm (375 N/mm2)

ATC St37 0,75 4,00 1970 100

Ø 4,0 mm (375 N/mm2)
Shear load: Figures obtained with dis-
placement of 3 mm between purlin and ATC St37 0,75 8,00 2530 84
sheet. Ø 4,8 mm (375 N/mm2)

Tensile breaking load Zb (N) Z

Zb
b

Ø 3,2 x = 1350
Ø 4,0 x = 2500
Ø 4,8 x = 3400

Shear breaking load Qb (N) Qb

Qb
Ø 3,2 x = 1100
Ø 4,0 x = 1650
Ø 4,8 x = 2400

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

TTO

Pull-out load FZ (N)

Fz

Part II (Subconstruction)

Type Material Thickness (mm) x– s Pre drill-Ø (mm)

St37 0,75 890 33
Ø 4,8 mm 4,9
St37 1,20 1820 50

TTO
Ø 4,8xL
Material
Sleeve: Shear load FQ(N) FQ
TTO – Steel zinced
Material number 1.0303
Mandrel:
TTO – Carbon steel zinced
FQ
Size
Shank: Thickness in mm
Ø 3,2/4,8 mm –x
Head: Type Material Part I Part II s
Ø 6,5/9,5 mm TTO St37 0,75 4,00 3570 50
Ø 4,8 mm (375 N/mm2)

Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.

Tensile breaking load Zb (N)

Z
b Zb

Ø 3,2 x = 1550
Ø 4,8 x = 3850

Shear breaking load Qb (N) Qb

Qb
Ø 3,2 x = 1060
Ø 4,8 x = 2900

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value June/2004 sre/abjo

TTC

TTC
Ø 4,8xL

Material
Sleeve:
Carbon steel
Material number
Mandrel:
Carbon steel
Material number

Size
Shank:
Ø 4,8 mm
Head:
Ø 9,5 mm

Tensile breaking load Zb (N)

Z
b Zb

Ø 4,8 x = 2800

Shear breaking load Qb (N) Qb

Qb
Ø 4,8 x = 2400

All stated values are x values, representing the arithmetical mean value from laboratory
testing concluded up to now, appropriate safety margins should be applied for field
conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SSC

Pull-out load FZ (N)

Fz

Part II (Subconstruction)

Type Material Thickness (mm) x– s Pre drill-Ø (mm)

SSC St37 (375 N/mm )2
0,75 460 50
Ø 4,8 mm 4,9
St37 (375 N/mm )2
1,20 1030 120

SSC
Ø 4,8xL
Shear load FQ(N) FQ
Admission SSC
DIBt Z-14.1-4

Material
FQ
Sleeve:
stainless steel A2 Thickness in mm
Material number 1.4301 –x
Type Material Part I Part II s
Mandrel:
stainless steel C1 SSC Alu (230 N/mm2) 1,80 1,80 4100 260
Material number 1.4021 Ø 4,8 mm
St37 (375 N/mm ) 2
1,20 1,20 3400 160
Size Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.
Shank:
Ø 3,2/4,0/4,8 mm
Head:
Ø 6,0/8,0/9,5 mm

Tensile breaking load Zb (N) Z

b Zb

Ø 3,2 x = 2500
Ø 4,0 x = 4000
Ø 4,8 x = 5500

Shear breaking load Qb (N) Qb

Qb
Ø 3,2 x = 2000
Ø 4,0 x = 3000
Ø 4,8 x = 4500

x = arithmetical mean value All stated values are x values, representing the arithmetical mean value from laboratory
s = Standard deviation testing concluded up to now, appropriate safety margins should be applied for field
conditions. Consult also your country’s approval documents.
 Technical value Mai 2004 sre/hch

SSO
Pull-out load FZ (N)

Fz
Part II (Subconstruction)

Material Thickness (mm) x– s Pre drill- Ø mm

St37 (375 N/mm ) 2
0,50 501 21
0,75 873 27
1,00 1250 27
4,9
SSO 1,25 1711 26
Ø 4,8xL 1,50 2358 129
2,00 4017 103
Material
Sleeve: St52 (550 N/mm ) 2
0,55 1091 26
stainless steel A2
Materialnummer 1.4301, AISI 304 (170 N/mm2) 2,00 4191 76
Mandrel:
stainless steel A3
Materialnummer 1.4541

Size
Shank:
Ø 4,8 mm
Shear load FQ (N) FQ
Head:
Ø 9,5mm

FQ
Thickness (mm)

Material Part I Part II x – s

St37 (375 N/mm ) 2
2,00 0,50 1296 113
(550/170 N/mm2) 2,00 0,55 2243 438
(170/550 N/mm2) 0,55 2,00 3669 55

Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.

Tensile breaking load Zb (N) Z

b Zb

x = 5400

Shear breaking load Qb (N) Qb

Qb
x = 4250

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

CNSO

Pull-out load FZ (N)

Fz

Part II (Subconstruction)

Type Material Thickness (mm) x– s Pre drill-Ø (mm)

CNSO St37 (375 N/mm )
2
0,75 820 19
Ø 4,8 mm 4,1
St37 (375 N/mm )
2
1,20 1620 60

CNSO
Ø 4,8xL Shear load FQ(N) FQ
Part II
Material
Part I
Sleeve:
FQ
Kupfer/Nickel 30 Fe
Material number 2.0882
Mandrel: Thickness in mm
stainless steel A3 –x
Type Material Part I Part II s
Material number 1.4541
CNSO St37 (375 N/mm ) 2
0,75 3,00 2730 95
Size Ø 4,0 mm
Shank:
Ø 4,0 mm Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.
Head:
Ø 8,0 mm

Tensile breaking load Zb (N) Z

b Zb

Ø 3,2 x = 2710

Shear breaking load Qb (N) Qb

Qb
Ø 3,2 x = 4950

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

GA-AS

Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) Pre drill-Ø 2,5 mm Pre drill-Ø 4 mm

–x s –x s
Alu (230 N/mm2) 3,00 3400 52 – –
St37 (375 N/mm )
2
0,75 1785 39 1373 49
GA-AS 1,00 2806 78 2246 69
Ø 6,5xL 1,25 3940 140 3170 128
Embedment (mm)
Material
Wood 25 – – 2290 –
Fastener:
35 – – 4070 –
stainless steel A2, 18/8
Material number 1.4301, AISI 304
Washer:
stainless steel A2, 18/8
Material number 1.4301, AISI 304 Shear load FQ (N)
with vulcanized EPDM

Size
Head/Drive:
Hex., 3/8” (9,5 mm) A/F

Washer: Thickness in mm
Ø 16 mm
Material Part I Part II x– s Part II –x s
St37 0,63 3210 – 4060 –
(375 N/mm2) 0,75 4520 – 5420 –
Shear load: Figures obtained with 1,00 1,00 5040 – 3,00 7090 –
displacement of 3 mm between purlin 1,25 5100 – 8780 –
and sheet. 1,50 5130 – – –

Tensile breaking load Zb (N)

x = 16000

Shear breaking load Qb (N)

x = 12000

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

GA-BS
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) –x s Pre drill Ø

St37 (375 N/mm2) 2,00 3880 5 4,90
4,00 14090 51 5,35
5,00 17590 70 5,65
6,00 16140 27 5,80
GA-BS 8,00 20660 59 5,80
Ø 6,3xL
Pull-over load Fu (N) Part II
Material
Fastener:
stainless steel A2, 18/8
Material number 1.4301, AISI 304 Part I
Washer:
stainless steel A2, 18/8 Washer S16
Material number 1.4301, AISI 304 Material Sheet thickness
with vulcanized EPDM Part I
–x
(mm) s
Size
Head/Drive: St37 (375 N/mm )
2
0,50 4060 –
Hex., 3/8” (9,5 mm) A/F 0,63 5500 –
0,75 5920 –
Washer: 0,88 7720 –
Ø 16 mm 1,00 8490 –

Shear load FQ (N)

Thickness in mm Washer S16

–
Material Part I Part II x s
St37 (375 N/mm ) 2
0,75 4570 –
Shear load: Figures obtained with dis- 0,88 6520 –
placement of 3 mm between purlin and 1,00 4,00 6740 –
sheet. 1,25 11270 –

Tensile breaking load Z (N)

b

x = 16000

Shear breaking load Qb (N)

x = 12500

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

MB/MBR (SDF–K)

Pull-out load FZ (N)

(permissible loads
for single pegs)
Part II (Subconstruction)
–
Brick 70 mm 600 – 10,50
Lime stone 70 mm 600 – 10,50
MBR Concrete Ž B15 50 mm 800 – 10,50

MB/MBR
Shear load Fq (N)

Admission MB/MBR
DIBt Z-21.2-177

Thickness in mm
Material
Peg sleeve: Material x– s
high quality Polyamid
MB and steel galvanised 5030 –
Fastener:
MBR steel not rosting A4 7040 –
steel galvanized or
stainless steel 1.457, A4 Consider additionally the load-carryng capacity of the brick work.
Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.
Size
Head/Drive:
Torx TX40 or
Hex. 6 mm A/F

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value October 2005 sre/abjo

TW–S/TW–A4

Pull-out load FZ (N)

Part II (Subconstruction)
–
Type Material Embedment x s
(mm)

TW–S TW–A4 TW–S Ø 4,8 Timber 13 1277 94

Ø 4,8xL Ø 4,8xL and TW–A4 11% 26 3023 108
and 31 3671 160
Ø 6,0xL 41 4643 174
51 5877 235
Admission TW-S
DIBt Z-31.1-79 TW–S Ø 6,0 Timber 35 4659 150
Admission TW-A4 6,5%
DIBt Z-33.2-10, 33.2-17

Material
Fastener: Shear load FQ (N)
TW-S: stainless steel A2,
Material number 1.4567, AISI 304
TW-A4: stainless steel A4,
Material number 1.4578, AISI 316

Size
Thickness in mm
Drive:
Torx T20W Type Material Part I Part II –x s
Head:
Ø 12 mm TW–S Ø4,8 Eternit 8 (mm) 30 (mm) 1180 370
Wood Eternit Wood
Shear load: Figures obtained with TW–A4 Eternit 8 (mm) 30 (mm) 1590 70
displacement of 3 mm between purlin Wood Eternit Wood
and sheet.

Tensile breaking load Zb (N)

Ø 4,8 TW-S x = 7100

Ø 6,0 TW-S x = 10249
TW-A4 x = 7100

Shear breaking load Qb (N)

TW-S x = 5400
TW-A4 x = 5400

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Mai/2004 sre/abjo

AP 11
Pull-out load FZ (N)

Fz

Part II (Subconstruction)
–
Material Thickness (mm) x s Pre drill-Ø (mm)
Alu (230 N/mm2) 1,80 2340 60
St37 0,75 1230 53
5,1
1,20 2290 110
1,50 3382 43

AP11
Shear load FQ (N) FQ
Ø 5,0xL
Admission AP11
DIBt Z-14.1-4 / Z-31.1-56 FQ

Thickness in mm
–
Material Material Part I Part II x s
Sleeve: Alu (230 N/mm2) 1,80 12,00 2750 48
AIMg5
Mandrel: St37 0,75 12,00 2840 95
stainless steel A3 Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.
Material number 1.4541

Size
Shank:
Ø5 mm
Head:
Ø11 mm
Tensile breaking load Z (N) Z
b b Zb

x = 3785
s = 36

Shear breaking load Q (N) Qb

b

Qb
x = 2384
s = 32

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Februar/2003 sre/abjo

AP 14

Pull-out load FZ (N)

Part II (Subconstruction)
–
Material Thickness (mm) x s Pre drill-Ø (mm)

Alu (230 N/mm ) 2

1,50 2038 95
1,80 2460 105
2,40 3926 16
5,1
St37 0,75 1400 50
1,20 2470 144
1,50 2659 140

AP14
Ø 5,0xL
Shear load FQ (N) FQ
Admission AP14
DIBt Z-33.2-10, Z-33.2-17,
Z-33.2-177

Material
FQ
Sleeve:
AIMg5 Thickness in mm
Mandrel: Material Part I Part II –x s
stainless steel A3,
Material number 1.4541 Alu (230 N/mm )
2
1,80 12,00 2700 150
St37 0,75 12,00 2700 145
Size
Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.
Shank:
Ø5 mm
Head:
Ø14 mm

Tensile breaking load Z (N) Z

b b Zb

x = 3926
s = 16

Shear breaking load Q (N) Qb

b

Qb
x = 2558
s = 60

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Februar/2003 sre/abjo

AP 16
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) x– s Pre drill-Ø (mm)

Alu (230 N/mm ) 2
1,80 2410 65
St37 0,75 1210 75 5,1

St37 1,20 2360 75

AP16
Ø 5,0xL Shear load FQ (N) FQ
Admission AP16
DIBt Z-33.2-10, Z-33.2-17

Material FQ
Sleeve:
AIMg5 Thickness in mm
Mandrel: –
stainless steel A3 Material Part I Part II x s
Material number 1.4541 Alu (230 N/mm )
2
1,80 10,00 2800 75

Size St3 0,75 10,00 2710 85

Shank: Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.
Ø 5 mm
Head:
Ø 16 mm

Tensile breaking load Zb (N)

Z
b Zb

x = 3720
s = 19

Shear breaking load Qb (N) Qb

Qb
x = 2414
s = 51

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value May 2005 sre/abjo

Oktober/2002 sre/abjo

SDA 3–S4

SDA Material Dicke (mm) x s

Ø 4,8xL
Alu (230 N/mm2) 2,00 1870 100
SDA 3,00 3900 115
Ø 4,8xL
Material Alu (240-280 N/mm2) 1,00 800 48
Fastener: 1,25 1430 97
stainless steel A4, 18/8 2,00 1587 46
Material number 1.4401, AISI 316

Washer:
Alu, with vulcanized EPDM
Shear load FQ (N)
Size Part II
Head/Drive:
Hex., 8 mm A/F Part I

Thickness in mm
–
Material Part I Part II x s
Alu (230 N/mm2) 4 2 –
4900 70

Shear load: Figures abtained with displacement of 3 mm between Purlin and sheet.

Tensile breaking load Zb (N)

x = 8500

Shear breaking load Qb (N)

x = 5800

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober/2002 sre/abjo

SDA 3–S
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) –x s

Alu 230 N/mm 2
1,5 1500 50
2,0 2400 50
3,0 3400 50
SDA
Ø 4,2xL
Material
Fastener:
stainless steel A2, 18/8
AISI 304

Washer:
Alu, with vulcanized EPDM

Size Tensile breaking load Zb (N)

Head/Drive:
Lens head Ø 9 mm, Torx T20W

x = 4800

Shear breaking load Qb (N)

x = 3900

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value August 2004 sre/abjo

Oktober/2002 sre/abjo

SDA 3-SR2
Pull-out load FZ (N)

Part II (Subconstruction)

Material Thickness (mm) x s

Alu (230 N/mm2) 2 2417 103

SDA3
Ø 4,8x48 Shear load FQ (N)
Part II

Material
Fastener: Part I
stainless steel A4,
Material number 1.4578, AISI 316
Thickness in mm
Size –
Material Part I Part II x s
Head/Drive:
Counter sunk Ø10 mm, SR2 Drive I) Wood II)Alu 27 2 1680 110

Shear load: Figures obtained with displacement of 3 mm between purlin and sheet.

Pull-over load Fu (N) Part II

Part I

Material
Part II Part I
–x
(mm) (mm) s
Wood/Alu 27,0 2,00 1903 299

Tensile breaking load Zb (N)

x = 8200

Shear breaking load Qb (N)

x = 6300

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value August 2004 sre/abjo

SLA3–S4

Pull-out load FZ (N)

SLA3
Ø4,2xL
Material Part II (Subconstruction)
Fastener: –
Length L Ø Material Thickness (mm) x s
Length 19 mm/21 mm:
(mm) (mm)
stainless steel S4 = A4,
Material number 1.4401, AISI 316 19 4,2 AlMg 3,0 3367 128

Size
Head/Drive:
Lenshead, SR2 Drive

Shear load FQ (N)

Part II

Part I

Thickness in mm
–
Length L Ø Material Part I Part II x s
Shear load: Figures obtained with dis- (mm) (mm) (mm) (mm)
placement of 3 mm between purlin and
19 4,2 AlMg 4,0 3,0 8288 146
sheet.

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Oktober 2002 sre/abjo

SLA5–S4
Pull-out load FZ (N)

Part II (Subconstruction)
SLA5 Length L Ø Material Thickness (mm) –x s
Ø div.xL (mm) (mm)

Material 19 6,0 AlMg 1,8 2200 170

Fastener: 2,0 2220 120
Length 19 mm/21 mm: 3,0 3900 150
stainless steel S4 = A4, 21 6,0 AlMg 2,0 2630 120
Material number 1.4401, AISI 316 3,0 3980 160
Length 25 mm: 4,0 7430 220
stainless steel S = A2,
Material number 1.4301, AISI 304 25 5,5 AlMg 2,0 2070 200
5,0 7030 320
Size
Head/Drive:
Hex., 8 mm A/F
Shear load FQ (N)

Thickness in mm
Length L Ø Material Part I Part II –x s
(mm) (mm)
19 6,0 AlMg 4 2 4700 190
Shear load: Figures obtained with dis- 21 6,0 AlMg 4 2 4400 120
placement of 3 mm between purlin and
sheet. 25 5,5 AlMg 6 5 5900 280

Tensile breaking load Zb (N)

L19 x = 10000
L21 x = 10000
L25 x = 9600

Shear breaking load Qb (N)

L19 x = 7000
L21 x = 8000
L25 x = 7600

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 Technical value Februar/2004 sre/hch

TU-S
Pull-out load FZ (N)
Remarks:
Values determinated in the centre of plate.
Pre-drill-Ø 6,0 mm
*Support ring-Ø 200 mm
**Support ring-Ø 350 mm

Lable Panel thickness (mm) Embedment (mm) –x s

Trespa Meteon 8 5,5 1858* 104
8 5,5 1716** 49
10 5,5 2609** 252
13 5,5 3621** 191

Prodema 8 5,5 1701** 129

TU-S 10 6,5 2244** 292
12 9,5 2536** 431

Material Formica 10,5 5 1924* 264

Sleeve:
stainless steel A4, Max Exterior 8 5,5 1654** 160
Material number 1.4401, AISI 316 10 5,5 2626** 58
Mandrel: 10 5,5 2886* 211
Carbon steel zinced
Resopal 8 5,5 1951* 248
Size 10 5,5 2379* 267
Head/Drive:
Hex., 8 mm A/F Abet Laminati 8 5,5 2223* 140

Mandrel: Arpa 8 5,5 1449** 118

Ø 3,3x50 10 5,5 2014** 61

Gurea 10 5,5 1439** 162

13 5,5 2673** 121

All values are arithmetical mean values x of the failure load in N.

Shear load FQ (N)

Thickness in mm
Material Part I Part II –x s
Shear load: Figures obtained with dis-
placement of 3 mm between purlin and Alu
sheet. Trespa5 8 5840 180

Tensile breaking load Zb (N)

x = 8780

Shear breaking load Qb (N)

x = 6530

All stated values are x values, representing the arithmetical mean value from laboratory
x = arithmetical mean value testing concluded up to now, appropriate safety margins should be applied for field
s = Standard deviation conditions. Consult also your country’s approval documents.
 © SFS intec 2005 Technische Änderungen vorbehalten
RC 33.00.05 / Gedruckt in der Schweiz

SFS intec AG / CH-9435 Heerbrugg / Tel +41 71 727 57 26 / Fax +41 71 727 53 83 / www.sfsintec.biz/fs