f4 Main-Checklist
f4 Main-Checklist
f4 Main-Checklist
72 Rev: 0612
F-16
Block 50-52 / MLU
Checklists - Main Volume
CONTENTS
Check-lists
1 Contents
2 Verify Checks / Before Engine Start
3 Engine Start / Engine Check / After Engine Start
4 After Engine Start (Continued)
5 Fuel Check / Avionics power on
6 Trims Checks / Before Taxi / Taxi
7 If checks / Before Take Off
8 Normal Take Off / Airborne
9 Fence In / Initial Point
10 Egress / Fence Out
11 Refuelling / IF Checks Mnemonics
12 Descent / Approach / Before Landing
13 Final Approach / After Landing
14 Pre Engine Shut Down / Shut Down
15 Hotpit refueling / Supplemental procedures: ILS
VERIFY CHECK
1. Master FUEL Switch ON – Guard down PNL#3
2. Engine FEED Knob Set NORM PNL#3
3. Master LIGHT switch NORM PNL#2
4. Exterior Lights Anti Collision ON only PNL#2
5. CNI switch Backup PNL#3
6. EPU switch NORM PNL#4
7. ENG CONT switch PRI PNL#4
8. ECM switch OFF (B52)
9. Audio/comms As required (Com volume) PNL#15
10. Throttle OFF
11. Hook Switch Check UP PNL#1
12. LDG Gear Handle Down and locked PNL#1
13. EW (CMDS or EWMS) All OFF PNL#13
14. Master Arm SAFE PNL#1
15. Fuel QTY SEL knob Set NORM PNL#5
16. Sensor PWR PNL All OFF PNL#10
17. AIR Source NORM PNL#6
18. Avionics All OFF PNL#9&10
AVIONICS
1. Threat Warning Aux ON PNL#13
2. EWMS
RWR PWR ON PNL#13
JMR PWR ON PNL#13
Chaff CMDs ON PNL#13
Flares CMDs ON PNL#13
EWMS Mode Set as required PNL#13
3. Check CNI switch UFC
4. DED - UFC
Comms Set UHF and VHF as required
ALOW – MSL – BINGO SET as required
CRUS – TACAN SET to home base
VIP – VRP – Bullseye SET as required
WSPAN SET and check
5. MFD
DTE Load
S – Jettison Preset Jettison (exit S-J mode)
Flightplan Check and set
6. AUDIO
COMM1/2 Volume SET PNL#15
MSL /Threat Volume SET PNL#15
ILS Volume knob SET PNL#15
7. ECM panel As required (B52)
TRIM CHECK
1. TRIM AP DISC switch DISC PNL#12
2. Stick TRIM Button Activate in ROLL and PITCH (no stick mvt)
Check for no trimwheel and indicator motion
3. TRIM AP DISC switch NORM PNL#12
4. Actuate Trims Nose down/up
Flaperons L/R
Rudder L/R
5. Trims All NEUTRAL (reset)
BEFORE TAXI
1. Landing Lights ON PNL#1
2. Drift Co Switch Set Norm ICP
3. INS Check Check Stage 8.3
Check ALIGN flashes in HUD
4. INS switch NAV position PNL#9
5. Canopy Closed – locked - no light
6. Aircraft Lights Set Wing /Fus ON PNL#2
7. Radio Tower Request Taxi
TAXI
Action/Note: Apply Power smoothly, note computed speeds for 8-12 degrees
pitch rotation as briefed.
Warning: Do not exceed 14 degrees pitch in rotation.
AIRBORNE
1. Landing Light Off PNL#1
2. U/C Check Retracted - handle light Off
3. Engine Gauges in the Green
4. FUEL Verify Tank feeding and set NORM PNL#5
5. Radio Call airborne
6. DED STP mode, Select NXT
7. MFD Cycle – As Required
8. Drift Co Switch Set Drift ICP
9. Radio Channel – As Required
10. Wingman Set Formation and Route
11. Altimeter Declare transition level (Alt settings NI)
FENCE IN
1. Master Mode As Required AG or AA
2. Master ARM Set ARM PNL#16
3. Radar As Required
4. Chaff/ Flares PGM mode As Required PNL#13
5. ECM Jammer As Required PNL#13
6. RWR Check On PNL#13
7. RWR Mode Diamond Float mode or as required PNL#26
7. PFD Check no Faults
8. Master A/C Lights Check Off PNL#12
9. MFD Cycle/ Req data
10. A/G Weapons Set release parameters
11. Laser Switch ON if required PNL#16
12. Volumes Check threat, com, msl vol PNL#15
13. TGP pod Activate if required – double check
14. AGM65 Missile power Check ON if required – double check
15. AIM-9 Cooling head Check Cool
16. CAT config Check correct PNL#1
17. Radio Flight Set Defensive Formation
Note:
Avoid Radio Chatter when entering enemy airspace unless in case of
emergency. Use A/C or hands signals instead.
INITIAL POINT
EGRESS
1. Heading Check to friendly airspace
2. Caution Panel Check for Damage
3. Master Mode As Required (A/A)
4. Awacs Check Nearest threat
5. MFD Cycle As Required
6. Store config Set Cat I (if possible) PNL#1
7. ECM Jammer As Required PNL#13
8. EWMS mode+pgr At pilot discretion PNL#13
9. Flight Rejoin / Cover
10. DED A-LOW Set for Egress
11. Flight Check Status & Fuel - Rejoin
Note:
When engaging an A/A threat, Jettison remaining A/G stores, and select CatI
config. If threat is less than 10 Nm, Use Dogfight Mode
FENCE OUT
1. Threat Assume A/A Threat - AWACS
2. Master ARM Set Safe (According to Threat)
3. Laser switch Set Off PNL#16
3. Master Mode Set Nav
4. Radar Off (According to Threat)
5. ECM Jammer Off (According to Threat) PNL#13
6. RWR Mode As required
7. Chaff/ Flares Auto disp Set Off PNL#13
8. PFD Check no Faults
9. Radio Flight Fuel Check (Dest or Alt)
IF CHECKS MNEMONIC
Holding/enroute Approach setup
W Weather M Minimas
H Holding A Altimeter
O Obtain app clearance I Initial descent rate
L Letdown plate review L Letdown plate
D Descent checks M Missed Approach
S Speeds A Approach speeds
N Navaids
REFUELING
Tanker rejoin :
1. Radio Request Refueling
2. TCN Select TCN Channel (Texaco)
3. TCN Mode SET A/A TR
4. Heading Course to Intercept (HSI)
5. Altitude Tanker ALT – 1000 Ft
Before Precontact:
6. Master ARM Check Safe PNL#16
7. Sensors Check Nose Cold
8. EW Mode knob &ECM STBY and OFF
9. FCR STBY
10. RDR ALT STBY
11. EXT Lights DIM (night) – STEADY
12. ANTI COLLISION light OFF at Night
13. AIR REFUEL switch Open PNL#3
14. AR status indicator Check RDY Light On
Contact:
15. Boom Operator Follow Instructions and Lights
16. AR status indicator Check AR/NWS Light On
17. Fuel Transfer Monitor
Disconnect:
18. A/R DISC button Depress
19. Throttle Decrease power
Post Air refueling:
20. Air Refuel switch CLOSE
21. Fuel quantity Check
22. Master Arm / SMS As required
23. Tacan As required
24. EW Mode knob &ECM As required
25. FCR As required
26. RDR ALT As required
27. EXT Lights As required
Note:
For Approach use the F4 Letdown plates
DESCENT
1. Master Mode Set NAV
2. Master ARM Set Safe PNL#16
3. Altimeter Set & Check (transition ALT)
Check altimeter readings vs HUD altitude
4. Approach plates Reviewed
5. Instr Mode Select switch TCN/ILS or NAV/ILS PNL#21
6. TACAN channels Set according to approach plate
7. HSI course and bearings Set according to approach plate
8. GPS Input coordinates of IAF
9. Speeds Compute final approach speeds
APPROACH
1. Radio Tower Call Inbound
2. HUD Set (declutter, cycle mode)
3. Fuel Check Quantity/Transfer/Balance PNL#5
4. Radio Flight Assume LDG priorities
5. At IAF Follow ATC procedures unless Visual
Approach.
BEFORE LANDING
1. Radio Tower (5Nm out) Request Landing
2. A/C Weight Verify/Update Vref
3. A/C LDG/Taxi Lights Set On/ On PNL#1
4. Gear Check 3green-handle light off
5. Speed brake Fully Deployed
6. Drift Co switch Set Norm ICP
7. Traffic Announce traffic in sight if required
8. Radar/EW Check all STBY PNL#13
Note:
Unless previously cleared aerobatic manoeuvre is not permitted over the airfield.
Pitch and bank should not exceed 70° IAS<250.
FINAL APPROACH
LANDING
1. Speed Throttle Idle
2. AOA Maintain 13° for max aerobraking
3. Speed 80 kts Nosewheel: On the ground
Maintain Full aft stick
Engage NWS at taxi speed or when req.
4. Wheel brakes As required
AFTER LANDING
1. Speedbrake CLOSED
2. ILS OFF PNL#15
4. Landing/ Taxi Lights As required PNL#1
5. Radar Alt OFF PNL#10
HOTPIT REFUEL
Prior to HOTPIT Entry
1. AFTER LANDING CHECKS Complete
2. Radio Frequency Check proper tower frequency tuned
3. AIR REFUEL switch Open ; RDY light ON PNL#3
4. TACAN power knob Power OFF PNL#15
5. GND JETT ENABLE switch OFF PNL#2
COCKPIT LAYOUT
PANEL #13: EW Management PANEL #1: Gear panel
PANEL #16: MISC (armement) PANEL #2: Ext lights
PANEL #26: TWP (RWR) PANEL #3: Fuel Panel
PANEL #4: EPU Panel
PANEL #11: HUD toggle PANEL #5: Fuel QTY
PANEL #12: Trim controls PANEL #6: Air source
PANEL #17: Caution lights PANEL #7: Jet Start
PANEL #24: HUD controls PANEL #8: Eng gauges
PANEL #9: Avionic pwr
PANEL #10: SNSR pwr
PANEL #14: ICP
PANEL #18: Alt Flaps
PANEL #15: Audio
PANEL #19: Mpo
PANEL #23: UHF
PANEL #20: Idle detent
PANEL #25: O²
PANEL #21: Instr. Mode
PANEL #22: Test Panel