System Report

SR-102E  APRIL 2020

APA Simplified Wall Bracing

Method Using Wood Structural
Panel Continuous Sheathing
1. Basis of the System Report
ƒ 2018,
2015 and 2012 International Residential Code (IRC): Sections R104.11 Alternative
Materials, Design and Methods of Construction and Equipment, R301.1.3 Engineered
Design, and R602.12 Simplified Wall Bracing
ƒ 2018,
2015 and 2012 AWC Wood Frame Construction Manual for One and Two Family
Dwellings (WFCM)
ƒ APA Reports T2011L-33, T2012L-16, T2012L-30, T2014L-39, and other test data

2. System Description
The Simplified Wall Bracing Method described in this report provides building officials, builders
and designers with an approach and the supporting technical information to meet the
requirements of the 2018, 2015 and 2012 IRC Simplified Wall Bracing (Section R602.12). In
the development of this report, IRC Simplified Wall Bracing has been modified to increase
its applicability to a greater percentage of home designs. To achieve broad applicability and
acceptance, the system uses the most common type of wall sheathing, wood structural panels,
based on their superior structural performance.
To provide the user with the greatest possible architectural latitude, this report only covers
continuously sheathed wood structural panel bracing (IRC Method CS-WSP) with an increased
sheathing thickness (called “Performance Category” in product standards) and a closer nailing
schedule on the first story of a two-story structure and the first and second stories of three
stories (see Footnote e to Table 3). This approach increases the performance of the bracing
panels on the lower stories due to the additional restraint provided by the mass and stiffness
of the structure above, through strength from increased fastening and with the use of thicker
wood structural panel continuous sheathing. This enhanced performance on the lower stories
of multi-story structures leads to reduced length of required bracing in these areas, allowing for
the method to be used on homes with abundant window and door openings typically found on
the front and back elevations. These decreases in the required bracing of multi-story structures
are reflected in Table 3.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  1
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

Additional minimum braced wall panel length information taken from IRC Section R602.10 has
been added to this APA Simplified Wall Bracing Method. While this adds some level of complexity
over the IRC method, it greatly increases the usability of the method.
Design simplification and flexibility are achieved through the enhanced sheathing thickness and
nailing described in this report. Intermittent wood structural panel (Method WSP) and other
bracing methods, except as specified in Section 3.1, are outside the scope of this report. Like
the IRC Simplified Bracing Method, the APA Simplified Wall Bracing Method shall be permitted
for houses located in areas of low to moderate wind and seismicity. To increase the usability of
the method, this report includes additional details for IRC simplified bracing provisions. Also
included are references to specific areas of the IRC and other publications when additional
information is required. Buildings meeting the requirements of this report meet all of the
bracing requirements of the 2018, 2015 and 2012 IRC Section R602.10, Wall Bracing, with the
enhancements discussed in Section 3 of this report.

3. Methodology
3.1 Applicability
Residential structures must meet all of the following conditions when using this method:
1. The entire building shall be continuously sheathed with wood structural panels in accordance
with the requirements specified in this section.
2. Other bracing provisions of the 2018, 2015 and 2012 IRC Section R602.10, except as specified
herein, are outside the scope of this method.
3. The foundation or basement wall shall be concrete, masonry, or concrete slab, and the
structure above shall be three stories or less. Permanent wood foundations shall not be
permitted.
4. Floor cantilevers shall be no more than 24 inches beyond the foundation or bearing wall
below.
5. Stud wall height shall be 10 feet or less when using the minimum required bracing lengths
specified in Table 3 of this report unless adjustments are made for other wall heights up to 12
feet in accordance with Footnote c in Table 3 of this report.
6. Roof eave-to-ridge height shall be 15 feet or less.
7. Interior finish of exterior walls shall consist of minimum 1/2-inch gypsum boards installed
on the interior side fastened in accordance with IRC Table R702.3.5. Interior gypsum finish
is not required on continuously sheathed wood structural panels adjacent to garage openings
(Method CS-G) and continuously sheathed portal frame (Method CS-PF) bracing panels (see
Section 3.5 of this report).
8. Basic wind speed shall be 100 mph (nominal wind speed in the 2012 IRC, which is equivalent
to 130 mph ultimate design wind speed in the 2015 and 2018 IRC) or less and the Wind
Exposure Category shall be B or C.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  2
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

9. Seismic Design Category shall be A, B or C for detached one- and two-family dwellings or
Seismic Design Category A or B for townhouses.
10. Cripple walls, if present, shall be considered as the first story of the structure when using
this method unless they are designed in accordance with 2018, 2015 and 2012 IRC Section
R301.1.2. When the foundation has been engineered/designed to support all of the loads from
the structure above, the method described herein shall be permitted. Such foundation systems
may include cripple walls, daylight and pile foundations, and permanent-wood and insulated-
concrete-form foundations.
11. Horizontal joint blocking of the bracing panels may be omitted if the amount of bracing on a
given wall is two times or more than the minimum required amount of bracing derived from
Table 3 of this report after adjustment by the relevant footnotes.
3.2 Circumscribed Rectangle
The building shall be circumscribed as shown in Figure 1. The rectangle shall surround all
enclosed offsets and ­projections, such as sunrooms and attached garages, unless an attached
garage or portion of the building is to be designed as a separate structure in accordance with
IRC Section R301.1.3 or a separate element in accordance with Appendix A of this report. Open
structures, such as attached carports and decks, shall be permitted to be excluded. The rectangle
shall have no side longer than 60 feet and the ratio between the long side and the short side shall
not exceed 3:1.

FIGURE 1
RECTANGLE CIRCUMSCRIBING AN ENCLOSED BUILDING

Long side Long side

Typical wall
corner

Typical segments of Typical segments of

Short side

Short side

wall between corner wall between corner

Circumscribing Circumscribing
rectangle rectangle

FIRST FLOOR PLAN SECOND FLOOR PLAN

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  3
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

3.3 Wood Structural Panel Sheathing Materials

The wood structural panel sheathing shall be Rated Sheathing with a minimum 7/16 Performance
Category, meeting the requirements of Department of Commerce (DOC) PS1 or PS2.
3.4 Wood Structural Panel Sheathing Attachment
The wood structural panel sheathing shall be attached to framing in accordance with the
following requirements:
1. The sheathing shall be installed with minimum 8d common nails (0.131 x 2-1/2 inches)
spaced at 4 inches on center at panel edges and at 12 inches on center over intermediate
supports. For single-story or the top story of two- or three-story buildings, the sheathing may
be installed with 8d common nails (0.131 x 2-1/2 inches) spaced at 6 inches on center at panel
edges and 12 inches at intermediate supports.
2. The sheathing shall be applied continuously over all areas of the exterior walls except
windows and doors, and including gable ends, and shall be installed either vertically or
horizontally.
3. All horizontal panel joints shall occur over and be nailed to common framing or blocking with
an appropriate panel edge-nailing schedule in accordance with IRC Section R602.10.10.
4. Each end of a braced wall line with continuous sheathing shall have a 24-inch return corner,
as defined in IRC Section R602.10.7, or an 800-lbf hold-down attached to the end stud of the
braced wall panel closest to the corner.
ƒ If
a continuously sheathed braced wall line contains an opening greater than 20 feet, each
end of each of the remaining portions of the braced wall line shall have one of the conditions
described above.
ƒ If
a continuously sheathed braced wall line contains two or more offset braced wall lines, as
permitted in IRC Section R602.10.1.2, each end of each offset braced wall line shall have one of
the conditions described above.
5. Gypsum wallboard shall be installed on the opposite side of wall bracing panels. Gypsum
wallboard shall be 1/2-inch thick and shall be fastened with nails or screws in accordance
with IRC Table R702.3.5.
Exception: Gypsum wallboard shall be permitted to be omitted if the amount of bracing on
a given wall is equal to or greater than 1.4 times the minimum required amount of bracing
derived from Table 3 of this report after adjustment by the relevant footnotes.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  4
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

3.5 “Qualified” Bracing Panel

A single “qualified” bracing panel shall consist of a full-height portion of an exterior wall
continuously sheathed with wood structural panels with a minimum length as shown in Tables
1 and 2 of this report. The bracing panel shall have no openings, except that small drilled holes
in the wall sheathing and not penetrating the wall framing up to 1-1/2 inches for the passage
of wiring and utilities shall be permitted. When using narrow wall bracing methods CS-G and
CS-PF, the minimum permissible lengths and contributing lengths for computing available
bracing shall be as shown in Table 1 of this report. When using Method CS-WSP, Table 1 provides
the minimum permissible lengths and contributing lengths based on both the wall height and the
adjacent clear opening height. If an 8- or 9-foot-tall wall line is present, Method CS-WSP braced
wall segments less than the Table 1 minimum length may be used, but with a corresponding
reduction in contributing lengths for computing available bracing in accordance with Table 2 of
this report.

TABLE 1
MINIMUM LENGTH OF BRACED WALL PANELS
(Excerpt from the 2018, 2015 and 2012 IRC Table R602.10.5, modified in accordance with R602.12.3, Item 1)
Minimum Length (in.)
Adjacent clear Wall Height Contributing
Method opening height (in.) 8 ft 9 ft 10 ft Length (in.)
CS-G — 24 27 30 Actual Lengtha
CS-PFc — 16b 18b 20b 1.5 x Actual Lengtha
≤ 60 24 27 30
64 24 27 30
68 26 27 30
72 27 27 30
76 30 29 30
80 32 30 30
84 35 32 32
88 36 35 33
CS-WSP Actual Lengtha
92 36 36 35
96 36 36 36
100 36 36
104 36 36
108 36 36
112 36
116 36
120 36
a. Use the actual length when it is greater than or equal to the minimum length.
b. The wall height for CS-PF is based on the height of the portal frame, as documented in APA Report T2014L-39. The height
of the portal frame shall be measured from the bottom of the bottom plate to the top of the portal frame header.
c. See IRC Figure R602.10.6.4.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  5
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

3.5.1 Partial Credit for CS-WSP Panels

CS-WSP panels in 8- or 9-foot-tall walls between 20 and 24 inches in length that do not meet the
minimum length requirements of Table 1 shall be permitted for use as bracing units at a full or
reduced contributing length (depending on the adjacent opening height), as shown in Table 2 of
this report based on the latest APA research results, as documented in APA Reports T2012L-16 and
T2012L-30.

TABLE 2
PARTIAL CREDIT FOR CS-WSP LESS THAN FULL LENGTH WITH 8- AND 9-FOOT TALL WALLSa
Length of Full Height Adjacent to a Clear Contributing Length
Wall Height Method CS-WSP Panel Opening Height of Braced Wall Panel
(ft) (in.) (in.) or Less (in.)
≤60 24
64 22
68 20
24
72 18
76 16
80 14
8 or 9
≤60 20
64 18
68 16
20
72 15
76 13
80 11
a. Linear interpolation shall be permitted.

3.6 Computing “Qualified” Wall Bracing Length

Within an exterior wall, only those full-height wall panels with a length greater than or equal
to the lengths specified in Tables 1 and 2 of this report shall be deemed to contribute to
resisting lateral load, and counted toward the required bracing length. The total bracing length
contributing to the side of a rectangle is equal to the sum of the contributing lengths of each
“qualified” wall panel. Any length of a qualified bracing panel over the minimum bracing length
required in Table 1 of this report shall be permitted for use toward the total bracing length
required for that side of the rectangle. Thus, if the minimum requirement for a specific method is
24 inches in accordance with Table 1 of this report and two such panels with lengths of 26 and
34 inches are present, (26 + 34 =) 60 inches or (60/12 =) 5 feet of bracing are present and shall be
permitted for use in determining the total bracing length for that wall.
For Methods CS-G and CS-PF, the bracing length on either side of the opening is considered
a qualified bracing panel and contributes to bracing lengths for meeting the minimum length
requirements of Table 1 of this report. An example is provided in Appendix B.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  6
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

3.7 Length of Bracing Required

Determining the minimum bracing length required is relatively straightforward:
1. Circumscribe the building with a rectangle. The rectangle shall enclose the maximum
building length and width dimensions as described in Section 3.2.
2. Ensure that the long side of the rectangle is not greater than three times the short side of the
rectangle or greater than 60 feet. If it is greater, consider using the multiple rectangle method
covered in Appendix A. The alternatives are to:
ƒ use the “legacy” bracing provisions of IRC Section R602.10,
ƒ usethe multiple rectangle method in conjunction with the APA Simplified Wall Bracing
Method (see Appendix A), or
ƒ have the structure designed in accordance with IRC Section R301.1.3 and the International
Building Code (IBC).
3. With the dimensions of this circumscribed rectangle, use Table 3 of this report to determine
the bracing length that is required on each rectangle side perpendicular to the side used
to enter the table. Note that interpolation shall be permitted. Either value, the rounded or
interpolated value, shall be multiplied by a wall height adjustment factor in accordance with
Footnotes (c) and (d) in Table 3 of this report, as applicable.
If the upper and lower stories share common exterior wall lines and the amount of bracing on the
second floor equals or exceeds the amount of bracing located on the story immediately below, and
the distribution rules of Section 3.8 for all such stories are met, only the bracing in the bottom
story must be checked. If the bottom story checks out, the upper stories will be acceptable as well.
3.8 “Distribution Rules” for Bracing Panels
Once the required minimum bracing length has been determined for each side of the
circumscribed rectangle using Table 3 of this report, this bracing length shall be distributed along
the actual exterior walls of the structure. In distributing these bracing panels, all of the following
Distribution Rules shall be met:
1. The first qualified bracing panel on each side of the rectangle shall begin within 12 feet of the
wall corner. The 12 feet is measured between the wall corner and closest edge of the first full-
height qualified bracing panel.
2. The distance between the closest edges of adjacent full-height qualified bracing panels shall be
20 feet or less.
3. Any exterior wall line with a length of 8 feet or greater shall have, at a minimum, one bracing unit.
4. Parallel offset wall sections with 4 feet or less of each other shall be considered the same wall
when using the Distribution Rules in this section.
In some cases, a greater bracing length is required to meet the Distribution Rules than is required
by Table 3. In this case, the greater bracing length required by the Distribution Rules shall govern.
In any cases, the bracing length required by Table 3 or the Distribution Rules, whichever is greater,
shall be met.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  7
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

TABLE 3
MINIMUM REQUIRED BRACING LENGTH ON EACH SIDE
OF THE CIRCUMSCRIBED RECTANGLE FOR WIND EXPOSURE Ba, b, c, d
Minimum Required Bracing Minimum Required Bracing
Eave-to Length on Each Long Side Length on Each Short Side
Ridge Length of Short Side (ft) Length of Long Side (ft)
Wind Story Height
Speed Level (ft) 10 20 30 40 50 60 10 20 30 40 50 60

2.0 3.5 5.0 6.0 7.5 9.0 2.0 3.5 5.0 6.0 7.5 9.0
90 mph
nominal e
10 2.9 5.4 7.4 9.9 12.0 14.0 2.9 5.4 7.4 9.9 12.0 14.0
for the
2012 IRC e
4.1 7.9 11.2 14.5 17.8 21.0 4.1 7.9 11.2 14.5 17.8 21.0
or
115 mph
ultimate 2.6 4.6 6.5 7.8 9.8 11.7 2.6 4.6 6.5 7.8 9.8 11.7
for the
e
2018 and 15 3.3 6.2 8.5 11.4 13.8 16.1 3.3 6.2 8.5 11.4 13.8 16.1
2015 IRC
e
4.5 8.7 12.3 16.0 19.6 23.1 4.5 8.7 12.3 16.0 19.6 23.1

2.5 4.0 6.0 7.5 9.5 11.0 2.5 4.0 6.0 7.5 9.5 11.0
100 mph
nominal e
10 3.7 6.6 9.1 12.0 14.9 17.5 3.7 6.6 9.1 12.0 14.9 17.5
for the
2012 IRC e
5.0 9.5 13.6 17.8 21.9 25.6 5.0 9.5 13.6 17.8 21.9 25.6
or
130 mph
ultimate 3.3 5.2 7.8 9.8 12.4 14.3 3.3 5.2 7.8 9.8 12.4 14.3
for the
e
2018 and 15 4.3 7.6 10.5 13.8 17.1 20.1 4.3 7.6 10.5 13.8 17.1 20.1
2015 IRC
e
5.5 10.5 15.0 19.6 24.1 28.2 5.5 10.5 15.0 19.6 24.1 28.2
For SI: 1 ft = 304.8 mm
a. Based on IRC Table R602.10.3(1) and modified in accordance with APA Report T2011L-33.
b. Interpolation shall be permitted.
c. The Wall Height Adjustment Factor, as shown below, shall be used to multiply the minimum bracing lengths listed in the
table above to accommodate wall heights from 8 to 12 feet based on IRC Table R602.10.3(2). Interpolation shall be
permitted.

Wall Height (ft) Wall Height Adjustment Factor

8 0.90
9 0.95
Any Story 10 1.00
11 1.05
12 1.10

d. For Wind Exposure Category C, multiply length required from table above by 1.2 for single-story buildings, 1.3 for
two‑story buildings and 1.4 for three-story structures.
e. The first story of two stories and the first and second of three stories shall be continuously sheathed with wood structural
panels attached with 8d common nails (0.131 x 2-1/2 inches) spaced 4 inches on center around the panel perimeter and
at 12 inches on center over intermediate supports.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  8
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

4. Lateral Support
For bracing panels in exterior walls located along eaves where the distance between the top of
the top plates to the underside of the roof sheathing is 9-1/4 inches or less, blocking between the
rafters or trusses shall not be required. When the distance between the top of the top plates to
the underside of the roof sheathing above braced walls is greater than 9-1/4 inches and less than
15‑1/4 inches, attachment shall be in accordance with IRC Section R602.10.8.2, item 1. These
details are not duplicated here because they vary slightly between different editions of the IRC and
because the 15‑1/4‑inches limitation is not commonly exceeded.
If the vertical distance between the underside of the roof sheathing and the top of the top plate
is greater than 15‑1/4 inches, or if the user wants to use the wall sheathing to block raised‑heel
trusses to meet the wind uplift and lateral load requirements of IRC sections R602.3.5 and
R602.10.2.1, see APA System Report SR-103, Use of Wood Structural Panels for Energy-Heel Trusses,
or www.apawood.org/walls, for more information.

5. Limitations
Recommendations provided in this report are subject to the following conditions:
The exterior walls of the structure shall be continuously sheathed with a minimum 7/16
Performance Category wood structural panel sheathing meeting the requirements of DOC PS1
or PS2 and shall be attached to framing with 8d common nails (0.131 x 2-1/2 inches) at 4 inches
on center around the panel perimeter and at 12 inches on center over intermediate supports.
For exterior walls in single story structures or in the top story of multi-story structures, the 8d
common nails (0.131 x 2-1/2 inches) shall be permitted to be spaced at 6 inches on center around
the panel perimeter and at 12 inches on center over intermediate supports.
The APA Simplified Wall Bracing Method shall be applicable to buildings of no more than three
stories, subject to the applicability listed in Section 3.1 of this report.
When placed over masonry or concrete stem walls, wall bracing panels used in the APA Simplified
Wall Bracing Method shall meet the requirements of IRC Section R602.10.9.
While the APA Simplified Wall Bracing Method is not part of the code, it is based on the code
and other modifications permitted by IRC Section R301.1.3, Engineering Design. Further
modifications to the APA Simplified Wall Bracing Method by the user of this report are beyond the
scope of this report.
This report is subject to periodic review. The latest copy of this report is available for free
download at www.apawood.org/resource-library.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  9
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

Appendix A
The Multiple-Rectangle Procedure
A common issue faced by residential designers using the APA Simplified Wall Bracing Method
is applying it to houses that are too large and/or not rectangular in shape. Non-rectangular
building configurations include T-, L-, and U-shaped buildings. For smaller structures, the APA
Simplified Wall Bracing Method provides an easy solution by permitting the entire structure to be
circumscribed by a rectangle. Even with the circumscribed rectangle procedure described in
Section 3.2 of this report, some homes fall outside of the scope of the APA and IRC simplified
bracing provisions due to their size or non-rectangular shape.
The multiple-rectangle procedure described on page 9 simplifies FIGURE A1
the design process, while still providing a safe and code- FLOOR PLAN
compliant structure. An example is presented on page 10 for
40'-0"
an L‑shaped building. The same principles apply to T- and
U-shaped buildings, and other shapes that can be divided
into multiple rectangles. This multiple-rectangle procedure
shall be permitted when a structure has an exterior dimension
greater than 60 feet, and thus, falls outside of the scope of the

70'-0"
APA Simplified Wall Bracing Method, by dividing the structure
into two or more elements that meet the maximum dimension
requirements.

20'-0"
Figure A1 is an example of a floor plan that falls outside the
requirements of the APA Simplified Wall Bracing Method because 20'-0"
of the 70-foot building dimension.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  10
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

STEP 1: Divide the

FIGURE A2 – STEP 1
structure into rectangular
DIVIDE STRUCTURE INTO RECTANGULAR ELEMENTS
elements. There are often
multiple ways to do this. 40'-0" 40'-0"
Typically, the easiest solution
is to divide the building in
such a way that the “common Rectangle A Rectangle A
side” or “common wall line”

50'-0"

50'-0"
of the two rectangles contains
wall panels that are permitted
to be used for bracing (see
Figure A2). 20'-0" Rectangle
B
STEP 2: Determine bracing
requirements for each 20'-0"

20'-0"
Rectangle
individual rectangular B
element using the APA
Simplified Wall Bracing 20'-0"
Method. Each individual
rectangle is treated and braced
as if it were a completely FIGURE A3 – STEP 2
independent and separate DETERMINE BRACING REQUIREMENTS FOR EACH RECTANGULAR
ELEMENT SEPARATELY
structure from the other
rectangles. The braced wall
line lengths and distance
between braced wall lines are Rectangle A
measured on each rectangle Bracing requirement for Rectangle A
separately (see Figure A3). Bracing panel for Rectangle A
Note that any braced wall
line with a length of 8 feet
or greater must have at
a minimum of 3 feet of
equivalent bracing.
Rectangle Bracing requirement for Rectangle B
B
Bracing panel for Rectangle B

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  11
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

STEP 3: Rejoin the rectangles with bracing provided. The rules that must be applied to the
common side when rejoining the rectangles are presented below. Once rejoined, the increased
common-side bracing will reflect the appropriate distribution of load. See Detail A.

FIGURE A4 – STEP 3
REJOIN RECTANGLES WITH BRACING PROVIDED

Rectangle A Rectangle A Bracing requirement for Rectangle A

Bracing panel for Rectangle A

Rectangle
B

Bracing requirement for Rectangle B

Rectangle Bracing panel for Rectangle B
B

DETAIL A
EXPANDED VIEW OF COMMON SIDE BRACING

Rectangle A

Bracing panel for Rectangle A

Bracing panel for Rectangle B

Rectangle B

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  12
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

Rules for joining at the common side:

1. The total bracing from both rectangles along the common side must be provided on the
common side.
2. In the example shown in Figure A4, the common side of Rectangle A has a portion that
is interior and a portion that is exterior to the house, while the common side of Rectangle
B is entirely an interior wall. The bracing panels shall be permitted to be repositioned or
redistributed along the common side as long as the total of the panels is at least equal to the
total of the two separate rectangles.
3. The wall bracing location provisions of the APA Simplified Wall Bracing Method must be met
along the common side, as well as along the extended wall line.
4. When the common wall line for both rectangles is an interior wall, the common wall bracing
in the APA Simplified Wall Bracing Method shall be permitted to be made of Method GB
(Gypsum Board) bracing. In this common wall line, the amount of doubled-sided Method
GB bracing along the common wall shall be at least two times the required bracing length
of Method CS-WSP bracing found in Table 3 of this report. The Method GB bracing shall be
attached to both sides of the framing in accordance with IRC Table R602.10.4. The Method GB
panels shall be attached along all panel edges including the top and bottom plates. “Floating
the corners” shall not be permitted.
5. When the common wall line for both rectangles has both exterior and interior wall line
portions, the common wall bracing in the APA Simplified Wall Bracing Method shall be
permitted to be made of both Method CS-WSP and Method GB bracing. In this case, the
total length of the double-sided Method GB and the single-sided CS-WSP braced wall panels
together shall not be less than two times the required length of Method CS-WSP bracing listed
in Table 3 of this report (see Note 1 below). Method GB bracing shall be installed as required
in Item 4 above.
6. If insufficient bracing length is available along the common wall line in Item 5 above, use
Method CS-WSP in the entire common wall line, including the interior wall line portion, to
avoid the need to double the amount of wall bracing required in Table 3 of this report. If this
still does not provide sufficient bracing length, consider other options provided in Section 3.7,
Item 2, of this report.
Note 1: IRC Section R602.10.4.1.5 permits mixing bracing methods in a wall line provided that
the longest required bracing length of the mixed methods is used. As this report only provides the
bracing amount for CS-WSP and the double-sided Method GB is approximately 1/2 of the capacity
of Method CS-WSP, doubling the bracing amount listed in Table 3 of this report provides the
required amount of bracing for such cases.

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  13
APA Simplified Wall Bracing Method Using Wood Structural Panel Continuous Sheathing

Appendix B
Example for Computing Qualified Wall Bracing Length
An example wall configuration is shown in Figure B1. Wood structural panels of 7/16
Performance Category ­meeting DOC PS2 are used to continuously sheath the wall with 8d
common nails (0.131 x 2-1/2 inches) at 4 inches on center around the panel perimeter and at 12
inches on center over intermediate supports. The house configuration meets the applicability
requirements of this report (i.e., Sections 3.1 and 3.8).

FIGURE B1
AN EXAMPLE WALL CONFIGURATION
(Bottom story of two- or three-story structure)
9'-0"

60"

80"

16" 20" 72" 30" 12" 32"

THE QUALIFIED WALL BRACING LENGTH IS DETERMINED AS FOLLOWS:

Greater Greater Amount Of
Than Length Than Length Bracing Length
Segment Required in Contributing Required in Contributing Contributed
Length (in.) Table 1 Length (in.) Table 2 Length (in.) (in.)
16 No 0 No 0 0
20 No 0 Yes 11 11
72 Yes 72 — — 72
30 Yes 30 — — 30
12 No 0 No 0 0
32 Yes 32 — — 32
Total = 145 in. or 12.1 ft

Form No. SR-102E  ■  © 2020 APA – The Engineered Wood Association  ■ www.apawood.org  14
 APA Simplified Wall Bracing
Method Using Wood Structural
Panel Continuous Sheathing
We have field representatives in many major U.S. cities and in Canada
who can help answer questions involving APA trademarked products.
For additional assistance in specifying engineered wood products, contact us:

A PA H E A D Q UA R TE R S
7011 So. 19th St. ■ Tacoma, Washington 98466
(253) 565-6600 ■ Fax: (253) 565-7265

P RO D U C T SU P P O R T H E LP D E S K
(253) 620-7400 ■ [email protected]

D I SC L A I M E R
The information contained herein is based on APA – The Engineered Wood Association’s c­ ontinuing
programs of laboratory testing, product research, and comprehensive field experience. Neither
APA, nor its members make any warranty, expressed or implied, or assume any legal liability or
responsibility for the use, application of, and/or reference to opinions, findings, conclusions, or rec-
ommendations included in this publication. Consult your local jurisdiction or design professional to
assure compliance with code, construction, and performance requirements. Because APA has no
control over quality of workmanship or the conditions under which engineered wood products are
used, it cannot accept responsibility for product performance or designs as actually constructed.

Form No. SR-102E/Revised April 2020

© 2020 APA – The Engineered Wood Association