GIGAcontrol T

EN Translation of the Original Installation and Operating Manual

46820V001-452016-0-DRE-Rev.C_EN
 Table of contents
General Information ...................................................... 3
Symbols ........................................................................................... 3
Safety instructions ............................................................................ 3
General ...................................................................................... 3
Storage ...................................................................................... 3
Operation ................................................................................... 3
Type plate .................................................................................. 4
Intended use .................................................................................... 4
Dimensions ..................................................................................... 4
Technical data .................................................................................. 5

Installation preparations ............................................... 7

Safety instructions ............................................................................ 7
Personal protective equipment......................................................... 7
Safety instructions ............................................................................ 8
Information on wall installation ......................................................... 8
Cables – for wall installation............................................................. 8
Cables – for operators with integrated control unit........................... 8

Electrical installation..................................................... 9
Overview of the control system ........................................................ 9
Mains connection ........................................................................... 10
Selecting and switching mains voltage .................................... 10
Mains feed.......................................................................................11
3-phase operation .....................................................................11
Operation with Steinmetz circuit (capacitor) .............................11
Connecting the absolute encoder .................................................. 12
Emergency actuation, thermal contact and slack wire switch.. 12
External command initiators ........................................................... 13
Ferrite core .............................................................................. 13
Multiple button with 6 wires...................................................... 13
Multiple button with 4 wires...................................................... 13
Relay for status display (X12) ........................................................ 13

Initial operation ............................................................ 14

DIP switches .................................................................................. 15
(S1) .......................................................................................... 15
LEDs on board ............................................................................... 15
Message LED................................................................................. 15
(X1) .......................................................................................... 15
Reset .............................................................................................. 16
Initial commissioning ...................................................................... 16
Detecting motor direction ............................................................... 16
Defining end positions .................................................................... 17
Change the motor direction ............................................................ 17
Change the bottom end position .................................................... 17
End position inaccuracy ................................................................. 17

2
 General Information
Symbols Storage
 The control unit must be stored in an enclosed, dry area at a
CAUTION SYMBOL: room temperature of –25 to +65 °C at a relative humidity of 90 %
Important safety instructions! (non-condensing).
Caution – to ensure personal safety, it is important to observe
all instructions. Save these instructions!
Operation
 When using the automatic close function, ensure compliance with
IMPORTANT INFORMATION SYMBOL: EN 12453 (e.g. install safety devices such as photo relay).
Information, useful advice!  After installation and commissioning, all users must be instructed in the
function and operation of the system. All users must be informed of the
Refers to a respective picture in the introduction or main text. hazards and risks inherent in the system.
 Open and close the gate only if there are no persons, animals
or objects within its area of movement.
Safety instructions  Continuously monitor the gate while it is in motion and keep all persons
away from it until the gate is completely opened or closed.
General
 Do not drive through the door until it has been fully opened.
 These installation and operating instructions must be read, understood
and complied with by persons who install, use or perform maintenance  The control unit must be adjusted to ensure safe operation
on the control unit. in conformity with the standards.

 Installation, connection and initial commissioning of the control unit may

only be carried out by an electrician.
 The system manufacturer is responsible for the complete system.
The system manufacturer must ensure that all applicable standards,
directives and regulations applicable at the installation site are
observed. In addition to other items, the system manufacturer must
test and maintain the maximum approved closing forces in accordance
with EN 12445 (Safety in use of power operated doors, test methods)
and EN 12453 (Safety in use of power operated doors, requirements).
The system manufacturer is responsible for preparation of technical
documentation for the complete system and the documentation must
accompany the system.
 All electrical wires must be fitted tightly and secured against shifting.
 The manufacturer assumes no liability for injuries, damage or break-
downs that occur due to non-compliance with the installation and
operating instructions.
 Before commissioning, ensure that the mains connection matches the
specifications on the type plate. If this is not the case, the control unit
must not be operated.
 In case of a three-phase current connection, make sure that the motor
direction is clockwise.
 Installations with a fixed mains connection require an all-phase
disconnection device with appropriate fuses.
 The installation instructions must be kept within reach.
 Always ensure compliance with accident prevention regulations and
current standards in each respective country.
 Take heed of and comply with the “ASR A1.7 Technical Regulations
for Workplaces” of the committee for workplaces (ASTA).
(Applicable for the operator in Germany, observe and comply with
the applicable regulations in other countries).
 Before working on the control unit, always disconnect the power plug
or disconnect the mains voltage at a main switch (lock to prevent
activation).
 Regularly check power cables and wires for insulation defects or cracks.
If a wiring fault is found, switch off the power immediately and repair the
faulty cable or wire.
 Before switching on the power supply for the first time, make sure that
the plug-in terminals are in their correct positions, otherwise the control
unit may malfunction or be damaged.
 Observe the requirements of the local power supplier.
 Only use permissible fastening materials appropriate for the supporting
surface.
 Only use original spare parts of the manufacturer.

3
 General Information
Type plate Dimensions
 The type plate is located on the controller housing of the operator, GIGAcontrol T
or if the operator is integrated, on the operator itself.
 The type plate shows the exact type designation and the date
10
of manufacture (month/year) of the control unit. 5 5
10

Intended use
CAUTION! RISK OF DEATH!
All cords or straps necessary to operate the gate by hand
must be removed.

 The GIGAcontrol T control unit is intended exclusively for opening and

closing industrial gates, such as sectional, roller, and roller grille gates.
Any other use does not constitute intended use.
The manufacturer accepts no liability resulting from use other than 322
intended use. The user bears the sole responsibility for any risk
involved. It also voids the warranty.
 Only command initiators and sensors in good technical conditions
may be connected, and they must be used for the intended purpose
with awareness of the hazards as described by the installation and
operating manual.
 Gates automated with an operator must comply with all valid standards
and directives: e.g. EN 13241-1, EN 12604, and EN 12605.
 The gate must be stable and torsionally stiff, i.e. it must not bend
or twist when being opened or closed.
 Only use the control unit in dry, non-explosive areas.
 The control unit conforms to the requirements of the IP-code 54. It must
not be installed in areas with a corrosive atmosphere (e.g. salty air).

4
 General Information
Technical data
Control unit

Dimensions 322 x 105 x 105 mm (H x W x D)

Operating voltage 1/3~230 V AC; 3~400 V AC
Mains feed fuse 3.15 A T (internal)
Control voltage 24 V DC only for internal purposes
Control voltage fuse 0.8 A T
Temperature range –25 ºC to +65 ºC
Connection cross-section 1.5 mm2
Switching capacity 0.55 kW max.
Protection class IP54

Potential-free relay
Switching voltage 60 V DC
Switching capacity 1 A max.

5
 General Information

Declaration of Conformity
for the installation of an incomplete machine
in accordance with the Machinery Directive 2006/42/EC, Annex II, Section 1 A

SOMMER Antriebs- und Funktechnik GmbH

Hans-Böckler-Straße 21-27
73230 Kirchheim unter Teck
Germany

hereby declares that the industrial gate control unit

GIGAcontrol T
have been developed, designed and manufactured in conformity with the

• Machinery Directive 2006/42/EC

• Low Voltage Directive 2014/35/EU
• Electromagnetic Compatibility Directive 2014/30/EU
• RoHS Directive 2011/65/EU.

The following standards were applied:

• EN ISO 13849-1, PL “C” Cat. 2 Safety of machines – safety-related parts of controls

– Part 1: General design guidelines
• EN 60335-1, where applicable Safety of electrical appliances
• EN 61000-6-3 Electromagnetic compatibility (EMC) – interference
• EN 61000-6-2 Electromagnetic compatibility (EMC) – interference resistance

The following requirements of Annex 1 of the Machinery Directive 2006/42/EC are met:

1.1.2, 1.1.3, 1.1.5, 1.2.1, 1.2.2, 1.2.3, 1.2.4, 1.2.6, 1.3.2, 1.3.4, 1.3.7, 1.5.1, 1.5.4, 1.5.6, 1.5.14, 1.6.1, 1.6.2, 1.6.3,
1.7.1, 1.7.3, 1.7.4

The special technical documentation was prepared in accordance with Annex VII Part B and will be submitted
to regulators electronically on request.

The incomplete machine is intended for installation in a door system only to form a complete machine as defined
by the Machinery Directive 2006/42/EC. The gate system may only be put into operation after it has been established
that the complete system complies with the regulations of the above EC Directive.

The undersigned is responsible for compilation of the technical documents.

Kirchheim, den 20-04-2016 i.V.

Jochen Lude
Responsible for documents

6
 Installation preparations
Safety instructions Personal protective equipment
CAUTION!
Important instructions for safe installation.
Observe all installation instructions – improper installation
can lead to serious injuries!

CAUTION! RISK OF DEATH!

All cords or straps necessary to operate the gate by hand
must be removed.  Safety glasses (for drilling)
 Work gloves
 Use only suitable tools.
 Safety shoes
 The mains supply line that has been provided may not be shortened
or extended.
 Before commissioning, ensure that the mains connection matches the
specifications on the type plate. If this is not the case, the control unit
must not be operated.
 All devices to be connected externally must have a safe isolation of the
contacts from the mains voltage supply according to IEC 60364-4-41.
 Cables for external devices must also be installed in accordance with
IEC 60364-4-41.
 Live parts of the control unit must not be connected to the earth
or with live parts or protective conductors of other electrical circuits.
 The control unit should be mounted on a low-vibration surface to
eliminate vibrations that could have a negative effect on it over time
(e.g., a brick wall).

7
 Installation preparations
NOTE:
Safety instructions The dimensions specified here are the dimensions for drilling
the fastening holes.
CAUTION!
Housing dimensions: See the “Dimensions” section.
Important instructions for safe installation.
Observe all installation instructions – improper installation
can lead to serious injuries!

CAUTION!
Control or regulating units (buttons) in a fixed position must
be mounted within sight of the gate. They may not, however,
be mounted close to moving parts and must be at least 1.5 m 77
above the ground.

 The operator may be installed, connected and commissioned

by competent personnel only.
 Do not move the gate, if there are any people, animals or objects
in the area of movement.
296
 Keep disabled persons and animals away from the gate.
 Wear safety glasses when drilling the fastening holes.
 Cover all drill holes to prevent ingress of dirt.
 Before opening the housing, make sure that drilling chips or any other
material cannot fall into the housing.
 All electrical wires must be fitted tightly and secured against shifting.
 Before installing the control unit, inspect it for damage caused by
shipping or other causes.
 Never install a damaged control unit. Serious injuries may result.
 Keep the system disconnected from the power supply when installing
the control unit. • Only use permissible fastening materials appropriate for the supporting
 Electronic components may be damaged by electrostatic discharge surface.
when touched. • Attach housing to the substructure correctly.
 Do not touch the electronic components of the control unit
• Use suitable tools.
(boards etc.).
 Close unused cable inserts with suitable material to maintain
the IP-code 54. Cables – for wall installation

Information on wall installation

CAUTION!
Before working on the control unit, always disconnect
the power plug or disconnect the mains voltage at a main
switch and lock to prevent reactivation.
1 2 3 4
 Use indoors (see data regarding temperature and IP protection class).
 The substructure must be flat and low-vibration.
M ! !
 Mount the control unit housing vertically.
1. Safety circuit “Door stop 1” (2-pole terminal).
2. Encoder “RS485” (+/–/A/B; absolute value encoder; 4-pole terminal).
3. Motor (1~230 V/3~230 V/3~400 V; 5-pole terminal).
4. Protective earth (PE).

Cables – for operators with

integrated control unit

! !
1 2

1. Safety circuit “Door stop 1” (2-pole terminal).

2. Encoder “RS485” (+/–/A/B; absolute value encoder; 4-pole terminal).

8
 Electrical installation
Overview of the control system
Motor connection

X7

X2

W
U

V
LED display
LED1

X9
LED2
LED3

ON
ON
4 3 2 1

DIP switches
X8

K1
S1
X12
NO

End positions relay

COM NC

X4
(potential-free contacts)

K2

230V
Selecting and switching
mains voltage

400V
Message LED
X1

800mAT

Transformer fuse
Microswitch,

emergency release,
X11

thermal contact
F4

TR1

Absolute value encoder

K3
X9

S10082
X5
1
SAFETY

Slack wire contact,

2

slip door contact

3
4
STOP

F3
5

External command Mains connection

initiators fuses
6

3,15AT
7

F1

F2

3,15AT 3,15AT
8

3 2 1
X10
X6

X3

L1 L2 L3
Integrated button Protective earthing Mains feed
conductor

9
 Electrical installation
CAUTION! Selecting and switching mains voltage
Electrical work must be performed by qualified electricians
only. IMPORTANT!
It is important to ensure that the jumper on the board
CAUTION! conforms to the actual voltage. Otherwise the board may
be destroyed.
Observe the requirements of the local power supplier.

CAUTION!
The mains cable must only be replaced by the manufacturer,

X4
230 V
customer service or another electrician.

Mains connection For 1~230 V

NOTE: and 3~230 V

400 V
The connection depends on the mains and the operator with
which the control unit will be used.

The control unit is suitable for the following mains voltages:

1~230 V, 3~230 V or 3~400 V.

X4
230 V
NOTE:
Caution! Check the position of the jumper on the board before
switching mains voltage. An incorrectly positioned jumper
may destroy the control unit. For 3~400 V

400 V
The control unit must be protected from short-circuit and overload
by a nominal fuse value of 10 A per phase.
• A 3-pole automatic circuit breaker must be used with three-phase mains.
• A 1-pole automatic circuit breaker must be used with AC power supplies.
The control unit must have an all-phase mains circuit breaker conforming
to EN 12453.
This can be:
• a plug connection (max. 1.5 m cable length)
or
• a main switch.

NOTE:
The mains circuit breaker must be easily accessible
at a height between 0.6 m and 1.7 m.

The following fuses are required depending on the delivery state:

Control unit without mains plug:

Main switch, automatic circuit breaker on mains side, all poles (max. 10 A)

Control unit with 5-pole CEE plug (16 A):

16 A socket (fuse-protected with 3-pole three-phase automatic circuit
breaker 3 x 10 A)

Control unit with 3-pole CEE plug:

16 A socket (fuse-protected with 1-pole automatic circuit breaker 1 x 10 A)

10
 Electrical installation
Mains feed
NOTE:
If ground fault interrupters are integrated into the building installation, the control unit must not be connected unless the ground fault
interrupters are class B devices (all-current-sensitive ground fault interrupters). If different types of ground fault interrupters are used,
circuits may be interrupted incorrectly or not at all.

3-phase operation
3~400 V/Y
3~230 V/Δ
Motor connection Mains connection

M
PE PE PE L1 L2 L3
3~

U V W PE
3~400 V, N, PE/
3~230 V, N, PE

Operation with Steinmetz circuit (capacitor)

1~230 V/Δ
Motor connection Mains connection

M
1~ PE PE PE L1 L2 L3

U V W PE
1~230 V

11
 Electrical installation
Connecting the absolute encoder Emergency actuation, thermal contact and
Control unit slack wire switch
NOTE:
X9 If one of the devices has triggered at X11, the message LED
flashes quickly (approx. 2 Hz), see chapter “Error messages”.
gn 2 RS485
X11 = Manual microswitch emergency actuation and thermal contact
ye (connection with pink + grey motor cable).
4 RS485
X11
wt 3 GND
br 6 12 V+

X11
pk 1
Safety circuit

gr 5 NOTE:
If one of the devices has triggered at X6, the message LED
flashes quickly (approx. 2 Hz), see chapter “Error messages”.
Leads in pairs.
X6 = Slack wire switch (connection with spiral cable/gate socket) and slip
A/B – GND/+12 V – safety circuit
door contact.

Encoder
X6

SAFETY
1 4
Safety
circuit RS485 A
Safety
RS485 B 2 5 circuit

GND 3 6 12 V DC

12
 Electrical installation
External command initiators Multiple button with 4 wires
Also available from SOMMER.
Ferrite core
X6
NOTE:
To prevent electromagnetic errors, the individual strands 1
of the external command initiators must be led through
the supplied ferrite core on the control unit side. 2

3
OPEN
4

5
STOP
6

7
CLOSED
1. Bundle cables and insert in ferrite core. 8

Relay for status display (X12)

X12
NO

NC
2. Close ferrite core.
COM
Multiple button with 6 wires

X6 Potential-free relay
1 Switching voltage 60 V DC
Switching capacity 1 A max.
2

3
OPEN

5
STOP
6

7
CLOSED
8

13
 Initial operation
Wall mounting | wall installation Operator with integrated control unit

• Message LED

• Message LED

• Gate OPEN
• Gate STOP while the gate
is moving DOWN

• Gate STOP

• Gate DOWN
• Gate STOP while the gate
is moving UP

14
 Initial operation
DIP switches
(S1)
Setting the safety limit switch range:

100 incr. 150 incr. 200 incr. 250 incr.

DIP 1 OFF ON OFF ON

DIP 2 OFF OFF ON ON

Gate status display via external relay, setting of dead man function:

Function ON OFF
DIP 3 Gate status Signal in lower end Signal in upper end
display position position
(external
relay X12)
DIP 4 Dead man Dead man operation Pulse in direction
in direction gate gate OPEN and dead
OPEN and gate man operation in
CLOSE direction gate CLOSE

LEDs on board
LED 1 Lights up while moving towards gate CLOSE

LED 2 Lights up while moving towards gate OPEN

LED 3 Flashes 1 x second when the control unit is ready

for operation

Message LED
(X1)
Mode Explanation
Continuous Control unit is in teach-in mode for end
positions
LED blinks 1 x/second No end position programmed (factory setting)

LED blinks 2 x/second Fault (e.g. interruption of safety circuit,

end positions not programmed)
LED blinks 50 x/second No signal from absolute encoder
LED blinks 12 x/second Reset was successful

15
 Initial operation
Reset Detecting motor direction
(Reset to factory settings) NOTE:
Before initial commissioning can be started, the gate must
be moved to the middle position.
1. Press and hold all three keys of the three-way keys simultaneously
To move the gate to the middle position, it can be moved
for about 30 seconds.
to the required position with the emergency manual actuation
 Saved information on the end positions, motor direction and error or moved to the required position in emergency jog mode.
messages will be deleted.
 After about 30 seconds, the message LED flashes very quickly NOTE:
(about 12 x second). It is important to read the complete description of initial
commissioning carefully and in full and only then start
2. Release the keys.
commissioning to be able to complete the various
 The message LED now flashes slowly (approx. 1 x/second). commissioning steps correctly.

1. Press and hold the STOP button and the UP button simultaneously.
 After three seconds the motor automatically starts briefly, showing
Initial commissioning the motor direction.
The control unit has the factory settings on delivery. This means that end
positions are not programmed and no information on the motor direction
is stored. (See “Reset”). A) If the motor direction is correct, i.e. in OPEN direction:
2. Continue pressing the OPEN button and the STOP button
 The recognition of motor direction was successful
The control unit must be commissioned in the following sequence:
(The following (italic) steps can be skipped).

1. Detect and set the motor direction. B) If the motor direction is not correct, i.e. in CLOSE direction:

2. Teach-in the top end position. 3. Release the two buttons.

3. Teach-in the bottom end position. 4. Wait 3 seconds.

5. Press and hold the STOP button and the OPEN button simultaneously
again.
NOTE:
 After three seconds the motor automatically starts briefly
On completion of initial commissioning the end positions in the other motor direction, showing the motor direction.
can be reprogrammed separately.

NOTE: If the motor direction is correct, in the OPEN direction:

If the motor direction in item 1 must be corrected, the control
 The recognition of motor direction is successfully completed.
unit must first be reset to the factory settings. Then the initial
commissioning must be run again.  Continue pressing the OPEN button and the STOP button.

If the motor direction is not correct, i.e. in the CLOSE direction:

 Repeat process from B).

NOTE:
10 seconds after successful completion of recognition
of motor direction (and continuously pressed OPEN and
STOP buttons), the operator runs in the OPEN direction.
If a button is released during the process, the operator stops.

- The process can continued within 60 seconds by pressing

and holding the OPEN button and the STOP button again.

- If the process is not continued within this period,

the control unit automatically resets itself, after which
only jog mode is available.

16
 Initial operation
 If no button is pressed within this period, the program automatically
Defining end positions switches out of teach-in mode. The former end position is retained.
NOTE: 2. If the gate is at the desired top end position, release all buttons.
To ensure that any possible backlash in the gearing does 3. Press and hold the STOP button for 10 seconds to confirm the end
not displace the end positions, the top end position should position.
be approached from the UP direction and the bottom end
position from the DOWN direction.  After 10 seconds the message LED flashes 5 times and the
operator moves slightly in the DOWN direction.
 The teach-in process for the top end position is successfully
1. If the gate is at the desired top end position, release all buttons. completed when the message LED goes off.
 The control unit automatically switches to normal operation.
2. Press and hold the stop button for 10 seconds to confirm the end position.
 After 10 seconds the message LED flashes 5 times and
the operator moves slightly in the DOWN direction.
 The message LED then remains steady. Change the bottom end position
3. To teach in the bottom end position, press and hold the CLOSE button NOTE:
and the STOP button simultaneously.
The gate must not be in the bottom end position when
 The gate moves in the DOWN direction. the change mode is started. There must be sufficient
travel to allow the gate to move in the DOWN direction.
4. If the gate is at the desired bottom end position, release all buttons.
5. Press and hold the stop button for 10 seconds to confirm the end position. 1. To start change mode, press and hold the STOP button and
the DOWN button simultaneously. After 10 seconds the operator
 After 10 seconds the message LED flashes 5 times and
starts in the DOWN direction.
the operator moves slightly in the UP direction.
 Releasing one or both buttons will cause the operator to stop –
 The teach-in process for the end positions is successfully
The process can continued within 60 seconds by pressing and
completed when the message LED goes off.
holding the UP button and the STOP button again.
 The control unit automatically switches to normal operation.
 If no button is pressed within this period, the program automatically
Initial commissioning is completed. switches out of teach-in mode. The former end position is retained.
2. If the gate is at the desired bottom end position, release all buttons.
Change the motor direction 3. Press and hold the stop button for 10 seconds to confirm the end position.
 After 10 seconds the message LED flashes 5 times and the
NOTE: operator moves slightly in the UP direction.
To change the motor direction permanently, the control unit
must be reset and the process for “Detecting motor direction”  The teach-in process for the bottom end position is successfully
must be run. completed when the message LED goes off.
 The control unit automatically switches to normal operation.
NOTE:
If the phases of the mains feed are changed after
commissioning, the control unit detects this.
The motor switches off with an error message End position inaccuracy
if the UP button or the DOWN button is pressed.
The control unit is fitted with automatic position correction.
NOTE: If the gate afterrun changes, e.g. as a result of temperature variations,
On completion of initial commissioning the end positions changes in the spring tension of sectional gates, binding as a result of
can be corrected separately. mechanical damage, the control unit automatically corrects the stopping
distance to the defined position value. The correction can be made
Change the top end position as required in steps 1 to 3 gate cycles.

NOTE:
The gate must not be in the top end position when the change
mode is started. There must be sufficient travel to allow
the gate to move in the UP direction.

1. To start change mode, press and hold the STOP button and the
UP button simultaneously. after 10 seconds the operator starts
in the UP direction.
 Releasing one or both buttons will cause the operator to stop –
The process can continued within 60 seconds by pressing and
holding the UP button and the STOP button again.

17
SOMMER Germany

SOMMER Antriebs- und Funktechnik GmbH

Hans-Böckler-Straße 21-27
73230 Kirchheim/Teck
Germany

Telephone: +49 7021 8001-0

Fax: +49 7021 8001-100

[email protected]
www.sommer.eu

© Copyright 2016 All rights reserved.