TDS Fosroc Nitofoam 45 India PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

Fosroc Nitofoam 45 constructive solutions

Sprayable Polyurethane Foam for Thermal


Insulation

Uses
Application Substrate/ 15 - 40
Polyurethane based, two component HFC blown, free from Ambient Temp. Range, °C
CFC/HCFC sprayable rigid closed-cell foam system for the
Specific Gravity at 20°C: Part A ISO 1.23
insulation of roofs. Particularly suitable for coating with Fosroc Part B POLYOL 1.23
Polyurea, Polyurethane & Brushbond Roofguard system for Viscosity at 20°C, cps: Part A ISO 300
a combination of waterproof and fire-rated insulation system Part B POLYOL 600
for roofs. Compressive strength, ASTM > 400
D-1621/94, kPa
Advantages
Tensile strength, >500
Machine applied for efficient, & faster rate of application ASTM D1623/78, kPa:
Light weight, seamless, In-situ applied thermal insulation Adhesion to substrate, > 180
system ASTM D4541, kPa:
Provides thermal comfort & energy saving Thermal conductivity at ≤ 0.023
250C as per ASTM C518/91,
Overcoat with Fosroc Polyurea, Polyurethane & Brushbond W/m K:
Roofguard system, for a combination of waterproof & fire
rated insulation system Closed cell content % > 96
ASTM D2126/ASTM D2856)
Standards compliance Water absorption, < 2.5
ASTM C272
IS 12432-3 (2002): Application of Spray Applied Insulation
Water Vapour Transmission, 132
- Code of Practice, Part 3: Polyurethane/Polyisocyanurate (ASTM C518/ ASTM E96)
[CHD 27: Thermal Insulation]
Flash Points, ºC: Part A ISO > 200
Part B POLYOL > 65
Type-1 foam as per Table-1 of ASTM D 7425
Fire resistance, Class B2
Description DIN4102:

Fosroc Nitofoam 45 is a two component,HFC blown, free from Note: Results given above are derived from testing in a
CFC/HCFC polyurethane based sprayable rigid foam system, controlled laboratory environment. Test results from field-
closed-cell type, designed to meet insulation requirements in applied samples may vary from above - dependent on actual
roof applications. Nitofoam 45 is applied seamless in-situ and site conditions.
is ideal for fast return to service. Nitofoam 45 should be applied
Application instructions
through a suitable metered application machine, by specialist
applicators - details on request. Processing parameters

Fosroc Nitofoam 45 adheres to brickwork, concrete, wood, Block Temperature +40⁰C to +45⁰C
particle board, sheet metals. Fosroc Nitofoam 45 is used as Hose Temperature +40⁰C to +45⁰C
thermal insulation for buildings. Volume ratio 1:1
Fosroc Nitofoam 45 should be covered with a waterproofing Pressure 100 - 110 bar
coating system such as Fosroc Polyurea, Polyurethane &
Refer to Application section below.
Brushbond Roofguard Topcoat.
Substrate condition
Properties
The substrate must be dry, free of dust, grease, oil and
Form: Two component product contaminants. A dry substrate is necessary because the foam
comprising liquids base
and hardener system can react with substrate moisture, which can result in
Colour: Straw insufficient adhesion, open cellular foam system, low cross-link
(Part A ISO Yellow-Brown, density and integrity of the foam.
Part B POLYOL Clear
Fosroc Nitofoam 45

Mix Ratio, 1:1 by volume (base : Application


hardener)
A heated volumetric proportioning machine at 1:1 volumetric
Gel Time, secs: approx. 13
output fitted with spray gun, such as those manufactured by
Foam Density, kg/m3 45 to 50
ASTM D1622: Graco should be used for this product.

page 1 of 2
Fosroc Nitofoam 45

Nitofoam 45 may be applied on firm and dry substrates such as Atmospheric relative humidity should ideally be <70% for ap-
tar, bituminized felt, concrete, particle board etc. The thickness plication. If relative humidity is > 70%, atmospheric moisture
of the individual layers of applied foam should be minimum can enter the reaction mechanism and physical properties may
10 - 15 mm. be affected. If in doubt, contact Fosroc office for advice.

To guarantee a homogenous application, it is necessary to It should be noted that Fosroc Nitofoam 45 will turn yellow if
keep a constant operating temperature of the raw materials exposed to UV/sunlight. This will not cause any negative effect
in the equipment, including in the hose lines– see Processing on the physical properties of the product.
Parameters.
Fosroc Nitofoam 45 should be covered with a waterproofing
Accurate dispensing of the product in the correct proportion coating system such as Fosroc Polyurea, Polyurethane &
produces a reaction mixture which forms a seamless foam layer Brushbond Roofguard Topcoat.
onto the substrate. Fosroc Nitofoam 45 has been formulated
Pack Quantity
to ensure its immediate expansion upon hitting the substrate
and to prevent a downward flow of material. Fosroc Nitofoam Nitofoam 45 450 Kgs Unit
45 should be applied in at least three successive layers. Each (Available in two pack size) ( Polyol 200 Kgs + ISO
layer must have a minimum thickness of 10 -15 mm. The total Mixing proportion by 250Kgs)
Volume (1:1)
minimum nominal thickness of foam is 25 mm.
460 Kgs Unit
Cleaning (Polyol 210 Kgs + ISO
250Kgs)
When necessary, clean equipment with Fosroc Equipment
Cleaner; ensure any mixed material is cleaned immediately
Health and safety
after use. Cured material can only be removed mechanically.
Refer to appropriate Product Safety Data Sheet.
Limitations
Storage
For use on plastic surfaces, adhesion testing should be car-
Fosroc Nitofoam 45 has a shelf life of 12 months if kept in a dry,
ried out prior to application. Contact the local Fosroc office for
advice. air conditioned store between +5⁰C and +30⁰C in the original
unopened containers.
Do not proceed with application if substrate is below 15°C or
is wet, if the surface temperature is <3ºC above the dew point Nitofoam and Fosroc are trademarks of Fosroc International
or if precipitation is imminent. Contact Fosroc office for advice. Limited

Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold
subject to its standard terms and conditions of sale, copies of which may be obtained on
request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification
or information it may give is accurate and correct, it cannot, because it has no direct or
continuous control over where or how its products are applied, accept any liability either
Fosroc Chemicals directly or indirectly arising from the use of its products whether or not in accordance with
any advice, specification, recommendation or information given by it.
(India) Pvt. Ltd.
Head Office telephone fax e-mail
Embassy Point, No. 150,
2nd Floor, Infantry Road, +91 80-42521900 +91 80-22281510 [email protected]
Bangalore 560 001,
Karnataka

Regional Offices

Chennai Mumbai Noida Kolkata


Hills Centre,Old No 5, MBC Park, 12th floor, Office No.12B, Unit No. 601, Highway Tower-II 304, Jodhpur Park
New No 9, 3rd Cross Street, ‘D’ Block, Near G Corp/Hyper City A-13/2, 6th Floor, Sector– 62 Kolkata 700 068
Jeth Nagar, Raja Annamalaipuram, Kasarwadawali, Ghodbunder Road, Gautam Buddha Nagar, Ph:+91 33-65343188
Chennai 600 028. Thane (West) 400 615 Noida 201 309, Uttar Pradesh Fax: 033-2499-0280
Ph: +91 44 61304500 Ph: +91 22 6229 6800 Ph: +91 120 6121900
Fax: 022 62296809 Fax: 0120-4270622

www.fosroc.com
page 2 of 2 NDIA/2020/0848/A

You might also like