Scribd Logo
Upload

Welcome to Scribd!

  • 34 views

    1.5mm Thick, Self-Adhesive Membrane: Bituthene® CP

    Uploaded by

    Steve Aoki

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    1.5mm Thick, Self-Adhesive Membrane: Bituthene® CP

    Uploaded by

    Steve Aoki
    34 views2 pages

    Original Title

    Bituthene CP

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    34 views2 pages

    1.5mm Thick, Self-Adhesive Membrane: Bituthene® CP

    Uploaded by

    Steve Aoki

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    P R O D U C T D ATA S H E E T

    Bituthene® CP
    1.5mm thick, self-adhesive membrane

    Product Description

    Bituthene® CP is a 1.5mm thick flexible, preformed waterproof membrane comprising a HDPE


    polyethylene film and a thick self-adhesive rubber/bitumen compound. The membrane has been
    designed and specially formulated to withstand high ambient temperatures.

    Continuity is achieved by overlapping adjacent rolls by 50mm and firmly rolling. Being factory made,
    the thickness of the membrane is constant throughout and is not subjected to variation by site labour
    as occurs with brush applied membranes.

    Typical Performance Properties


    Product Advantages
    • Chemically-resistant — provides effective external Property Typical Values Test Method
    protection against aggressive soils. Tensile Strength (Film) 19,700kN / m2 ASTM D882
    • Single layer — simple, reliable, low labour cost. Tensile Strength M.D: 1.3N / mm 2
    ASTM D412
    • Cold-applied — self-adhesive overlaps ensure (Composite) C.D: 1.1N / mm2
    continuity. Elongation (Composite) ≥ 300% ASTM D412
    • Flexible — accommodates minor settlement and Puncture Resistance 9kg ASTM E154
    shrinkage movement.
    Adhesion to Self 1,100N / m GCP Test
    Method B77
    Pliability Pass GCP Test
    Method
    Installation
    Measures should be taken to ensure that all surfaces are free from Any punctures or damaged areas should be cleaned and patched
    ice, frost or condensation. Installation is recommended between using Bituthene CP with 50mm laps all round.
    +10°C and +40°C. Pipe entries may be sealed prior to the application of Bituthene
    Concrete blinding under base slab should be surface dry, free CP with Liquid Membrane extended over the adjacent flat slab
    from standing water, and laid to a regular surface free from sharp area to give a minimum 50mm lap under the Bituthene CP. Liquid
    protrusions and hollows. Membrane is a two component compound for waterproofing
    irregular profiles in conjunction with Bituthene systems.
    Horizontal surfaces under base slabs do not usually require priming
    before applying the membrane. Where Bituthene is to be left temporarily exposed on vertical
    surfaces, batten fixing may be necessary to prevent slippage. Prior
    Vertical surfaces shall be smooth, regular, dry and free from nails
    to backfilling remove battening and cover fully with a subsequent
    and primed with one coat of Bituthene Primer N applied by brush
    layer of Bituthene.
    or roller at a rate of 5 to 8 sq m / L depending on the porosity of
    the surface, and allowed to dry completely before the application Following application care should be taken to prevent damage by
    of the Bituthene CP. Brickwork shall be flush pointed or rendered to following trades by using a 25mm screed as Bituthene protection
    provide a smooth surface before priming. boards spot bonded with Pak Adhesive. Vertical faces to be
    protected if required against damage from backfilling and fixing of
    Bituthene CP shall be laid by peeling back the protective release
    reinforcement by using Bituthene protection boards recommended
    paper and applying the adhesive face onto the prepared surface.
    by spot bonded with Pak Adhesive.
    The material should be brushed on to the surface to ensure good
    initial bond. Adjacent rolls are aligned and overlapped 50mm
    minimum at side and ends and well rolled with a firm pressure using
    a Lap Roller to ensure complete adhesion and continuity between
    the layers.
    Specification Complementary Materials
    See separate data sheets
    Bituthene CP preformed, self-adhesive membrane shall be laid on
    to smooth concrete substrates and on to vertical surfaces primed
    with Bituthene Primer N applying the preformed membrane sticky Equipment by Others
    side downwards, to give well rolled 50mm overlaps, and shall be Soft brush, Stanley knife, brush or roller for priming. Stiff broom
    laid strictly in accordance with the manufacturer’s instructions. and airline for cleaning surface.

    Supply Health and Safety


    Refer to relevant Material Safety Data Sheets.
    Bituthene CP 1m x 20m roll
    Average net weight 38Kg
    Palletisation Up to 25 rolls per pallet
    Quality Assurance
    Storage Store upright in dry conditions GCP Applied Technologies is certified to ISO 9001 by TUV SUD
    below 35ºC PSB Pte Ltd..
    Nominal Thickness 1.5mm

    Bituthene CP 1m x 16m roll


    Average net weight 38Kg
    Palletisation Up to 25 rolls per pallet
    Storage Store upright in dry conditions
    below 35ºC
    Nominal Thickness 2mm

    Bituthene CP 1m x 12m roll


    Average net weight 38Kg
    Palletisation Up to 25 rolls per pallet
    Storage Store upright in dry conditions
    below 35ºC
    Nominal Thickness 2.5mm

    Ancillary Products
    See separate data sheets
    Bituthene Primer N 20L / pail
    Coverage 5 to 8 sq metre / L
    depending on method of
    application, surface
    texture, porosity and
    ambient temperature
    Bituthene Liquid Membrane 5.7L
    Bituthene Mastic 4.5L / pail
    Lap Roller Unit

    gcpat.com | For technical information: [email protected]

    Australia 1800 855 525 New Zealand +64 9 448 1146 China Mainland +86 21 3158 2888 Hong Kong +852 2675 7898
    India +91 124 402 8972 Indonesia +62 21 893 4260 Japan +81 3 5226 0231 Korea +82 32 820 0800 Malaysia +60 3 9074 6133
    Philippines +63 49 549 7373 Singapore +65 6265 3033 Thailand +66 2 709 4470 Vietnam +84 8 3710 6168

    We hope the information here will be helpful.  It is based on data and knowledge considered to be true and accurate, and is offered for consideration,
    investigation and verification by the user, but we do not warrant the results to be obtained. Please read all statements, recommendations, and
    suggestions in conjunction with our conditions of sale, which apply to all goods supplied by us. No statement, recommendation, or suggestion is
    intended for any use that would infringe any patent, copyright, or other third party right.
    Bituthene is a trademark, which may be registered in the United States and/or other
    countries, of GCP Applied Technologies, Inc. This trademark list has been compiled using
    available published information as of the publication date and may not accurately reflect
    current trademark ownership or status.  
    © Copyright 2016 GCP Applied Technologies, Inc. All rights reserved. 
    GCP Applied Technologies Inc., 62 Whittemore Avenue, Cambridge, MA 02140, USA
    Printed in Singapore | 04/16 | 300-Bituthene-19

    You might also like