ABB IRC5 Compact Product Manual HAC047138-001 RevG en

ROBOTICS
Product manual
IRC5 Compact
Trace back information:
Workspace R17-2 version a11
Checked in 2017-09-20
Skribenta version 5.1.011
Product manual
IRC5 Compact
Release 17.2
Document ID: 3HAC047138-001

Revision: G
© Copyright 2009-2017 ABB. All rights reserved.

The information in this manual is subject to change without notice and should not
be construed as a commitment by ABB. ABB assumes no responsibility for any errors
that may appear in this manual.
Except as may be expressly stated anywhere in this manual, nothing herein shall be
construed as any kind of guarantee or warranty by ABB for losses, damages to
persons or property, fitness for a specific purpose or the like.
In no event shall ABB be liable for incidental or consequential damages arising from
use of this manual and products described herein.
This manual and parts thereof must not be reproduced or copied without ABB's
written permission.
Keep for future reference.
Additional copies of this manual may be obtained from ABB.
Original instructions.

ABB AB, Robotics
Robotics and Motion
Se-721 68 Västerås
Sweden
Table of contents
Table of contents
Overview of this manual ................................................................................................................... 9
Product documentation, IRC5 .......................................................................................................... 12
Network security ............................................................................................................................... 14
1 Safety 15
1.1 Introduction to safety information ......................................................................... 15
1.2 General safety information .................................................................................. 16
1.2.1 Introduction to general safety information .................................................... 16
1.2.2 Safety in the robot system ........................................................................ 17
1.2.3 Protective stop and emergency stop ........................................................... 19
1.2.4 Safety risks ............................................................................................ 21
1.2.4.1 Risks associated with live electric parts ........................................... 21
1.2.5 Safety actions ......................................................................................... 23
1.2.5.1 Fire extinguishing ........................................................................ 23
1.2.6 Safety data ............................................................................................. 24
1.3 Safety signals and symbols ................................................................................. 27
1.3.1 Safety signals in the manual ...................................................................... 27
1.3.2 Safety symbols on controller labels ............................................................ 29
1.4 Safety related instructions .................................................................................. 33
1.4.1 DANGER - Make sure that the main power has been switched off! .................... 33
1.4.2 WARNING - The unit is sensitive to ESD! ..................................................... 34
1.4.3 CAUTION - Never stand on or use the cabinet as a ladder .............................. 36
1.4.4 CAUTION - Make sure that there are no loose screws or turnings ..................... 37
1.4.5 CAUTION - Close the cabinet door ............................................................. 38
1.4.6 CAUTION - Hot components in controller ..................................................... 39
1.4.7 CAUTION - Make sure that all mode selector keys are kept safe ...................... 40
1.4.8 Recover from emergency stops ................................................................. 41
2 Installation and commissioning 43

2.1 Overview ......................................................................................................... 43
2.2 Installation activities .......................................................................................... 44
2.3 Unpacking the controller ..................................................................................... 45
2.4 On-site installation ............................................................................................ 47
2.4.1 Required installation space ....................................................................... 47
2.4.2 Mounting the FlexPendant holder ............................................................... 49
2.4.3 Mounting the controller in a 19" cabinet ....................................................... 51
2.5 Buttons and switches ......................................................................................... 53
2.5.1 Buttons and switches on the front panel ...................................................... 53
2.5.1.1 Brake release button .................................................................... 54
2.6 Connections ..................................................................................................... 55
2.6.1 Connectors on the IRC5 Compact controller ................................................. 55
2.6.1.1 Connectors on the controller .......................................................... 55
2.6.1.2 Connecting a FlexPendant ............................................................ 57
2.6.1.3 Connectors on the computer unit .................................................... 58
2.6.1.4 Connecting a serial channel to the controller .................................... 61
2.6.2 Connecting cables to the controller ............................................................. 63
2.6.3 Power supply system requirements ............................................................ 68
2.6.4 Connecting power supply ......................................................................... 71
2.6.5 Grounding ............................................................................................. 73
2.6.6 Fitting the connector ................................................................................ 74
2.6.7 Descriptions for connectors XS7 - XS17 ...................................................... 76
2.6.8 The MOTORS ON/MOTORS OFF circuit ...................................................... 80
2.6.9 Programmable stop functions .................................................................... 85
2.6.10 Emergency stop output ............................................................................ 88
2.7 Opening the IRC5 Compact controller ................................................................... 89
Product manual - IRC5 Compact 5

3HAC047138-001 Revision: G
Table of contents
2.8 Drive system .................................................................................................... 90

2.8.1 Drive functions, general ............................................................................ 90
2.9 Memory functions .............................................................................................. 91
2.9.1 Memory functions .................................................................................... 91
2.9.2 Connecting a USB memory ....................................................................... 92
2.10 I/O system ....................................................................................................... 94
2.10.1 Definition of fieldbuses, IRC5 .................................................................... 94
2.10.2 DeviceNet I/O units .................................................................................. 98
2.11 Installation of add-ons ........................................................................................ 99
2.11.1 Installation of external operator's panel ....................................................... 99
2.11.2 Installation of external enabling device ........................................................ 102
2.11.3 Installing the Safety module DSQC1015 for SafeMove .................................... 104
2.12 Testing ............................................................................................................ 109
3 Maintenance 111
3.1 Maintenance schedule, IRC5 Compact controller .................................................... 111
3.2 Inspection activities ........................................................................................... 112
3.2.1 Inspection of controller ............................................................................. 112
3.3 Changing/replacing activities ............................................................................... 113
3.3.1 Activities ............................................................................................... 113
3.4 Cleaning activities ............................................................................................. 114
3.4.1 Cleaning of control cabinet ....................................................................... 114
3.4.2 Cleaning the FlexPendant ......................................................................... 115
3.5 Function tests ................................................................................................... 118
3.5.1 Function test of emergency stop ................................................................ 118
3.5.2 Function test of mode switch ..................................................................... 119
3.5.3 Function test of three-position enabling device ............................................. 120
3.5.4 Function test of motor contactors K42 and K43 ............................................ 121
3.5.5 Function test of brake contactor K44 .......................................................... 122
3.5.6 Function test of auto stop ........................................................................ 123
3.5.7 Function test of general stop .................................................................... 124
3.5.8 Function test of reduced speed control ........................................................ 125
4 Repair 127
4.1 Overview ......................................................................................................... 127
4.2 Replacement of safety board ............................................................................... 128
4.3 Replacement of I/O unit ...................................................................................... 131
4.4 Replacement of backup energy bank .................................................................... 134
4.5 Replacement of computer unit ............................................................................. 138
4.6 Replacement of PCIexpress boards in the computer unit .......................................... 143
4.7 Replacement of Safety module DSQC1015 for SafeMove .......................................... 147
4.8 Replacement of expansion board in the computer unit ............................................. 151
4.9 Replacement of fieldbus adapter in the computer unit .............................................. 154
4.10 Replacement of fan in computer unit ..................................................................... 159
4.11 Replacement of SD-card memory in computer unit .................................................. 163
4.12 Replacement of drive unit ................................................................................... 165
4.13 Replacement of axis computer ............................................................................. 169
4.14 Replacement of contactor unit ............................................................................. 173
4.15 Replacement of brake resistor bleeder .................................................................. 175
4.16 Replacement of system fans ............................................................................... 178
4.17 Replacement of Remote Service box .................................................................... 181
4.18 Replacement of Ethernet switch ........................................................................... 184
4.19 Replacement of power supply .............................................................................. 187
4.19.1 Replacement of power distribution unit ........................................................ 187
4.19.2 Replacement of system power supply ......................................................... 192
4.19.3 Replacement of line filter .......................................................................... 197
6 Product manual - IRC5 Compact

Table of contents
5 Decommissioning 201
5.1 Introduction ...................................................................................................... 201
5.2 Environmental information .................................................................................. 202
6 Reference information 203

6.1 Introduction ...................................................................................................... 203
6.2 Applicable standards ......................................................................................... 204
6.3 Unit conversion ................................................................................................. 206
6.4 Standard toolkit, IRC5 ........................................................................................ 207
6.5 Screw joints ..................................................................................................... 208
7 Spare parts 209

7.1 IRC5 Compact controller .................................................................................... 209
7.2 Manipulator cables ............................................................................................ 213
8 Circuit diagrams 217

8.1 Circuit diagrams ................................................................................................ 217
Index 219

This page is intentionally left blank
Overview of this manual

About this manual
This manual contains instructions for:
• installing the controller, mechanically as well as electrically.
• maintenance of the controller.
• mechanical and electrical repair of the controller.
Usage
This manual should be used during:
• installation and preparation work.
• maintenance work.
• repair work.
Who should read this manual?

This manual is intended for:
• installation personnel.
• maintenance personnel.
• repair personnel.
Prerequisites
Maintenance/repair/installation personnel working with an ABB Robot must:
• be trained by ABB and have the required knowledge of mechanical and
electrical installation/repair/maintenance work.
References
Reference Document ID
Product manual - IRC5 3HAC047136-001
Operating manual - Emergency safety information 3HAC027098-001
Operating manual - IRC5 with FlexPendant 3HAC050941-001
Operating manual - RobotStudio 3HAC032104-001
Operating manual - Getting started, IRC5 and RobotStudio 3HAC027097-001
Operating manual - Troubleshooting IRC5 3HAC020738-001
Application manual - MultiMove 3HAC050961-001
Application manual - Force Control 3HAC050377-001
Application manual - SafeMove 3HAC050974-001
Application manual - Electronic Position Switches 3HAC050996-001
Application manual - Functional safety and SafeMove 3HAC052610-001
Technical reference manual - RAPID Instructions, Functions and 3HAC050917-001
Data types
Technical reference manual - System parameters 3HAC050948-001
See Circuit diagrams on page 217.
Continues on next page

Continued
Note
The document numbers that are listed for software documents are valid for
RobotWare 6. Equivalent documents are available for RobotWare 5.
Revisions
Revision Description
- First edition.
Released with the new computer unit, DSQC1000.
A • New computer unit, DSQC1018, with two PCI slots and no knockout
plates. No functional change, but affects illustrations.
• Corrections on chapter Repair on page 127.
• Corrected article number for line filter in Replacement of line filter on
page 197.
• Clarified the use of the WAN port in section Connectors on the com-
puter unit on page 58.
B • Added mounting kit as spare part in section Mounting the controller
in a 19" cabinet on page 51.
• Some changes on how the ports can be configured and used is de-
scribed in section Connectors on the computer unit on page 58.
C Release 15.2.
• Minor corrections.
• Added safety-related information to sections CAUTION - Make sure
that all mode selector keys are kept safe on page 40, Function tests
on page 118, and Refurbish.
• Updates in section Applicable standards on page 204.
D Release 16.1.
• Updated cable info for IRB 1200 in section Manipulator cables on
page 213.
• Spare parts updated.
• Section Connecting cables to the controller added.
• New Remote service box introduced.
• Safe Move 2 information added.
• Circuit diagrams for Motors ON/OFF updated.
E Release 16.2.
• Added section Installing the Safety module DSQC1015 for SafeMove
on page 104.
• Added information that function tests should be performed after repla-
cing a component.
• Changes in the article names for some spare parts.
• Removed section Refurbish.

Continued
Revision Description
F Release 17.1.
• Added sections Function test of reduced speed control on page 125,
and Recover from emergency stops on page 41.
• Updated descriptions of stops in section Protective stop and emergency
stop on page 19.
• Added section Safety data on page 24.
• Updated list of labels in section Safety symbols on controller labels
on page 29.
• New computer unit DSQC1024 is introduced, see Computer unit parts
on page 210.
• Spare parts updated, see Manipulator cables on page 213.
• Added section Grounding on page 73.
• Information regarding new safety board DSQC400E added.
G Release 17.2.
• Updated list of applicable standards.
• Updated section Connecting cables to the controller on page 63.
• Added section Power supply system requirements on page 68.
• Spare parts updated, see Manipulator cables on page 213.
• Removed all references to computer unit DSQC1024.

Product documentation, IRC5

Categories for user documentation from ABB Robotics
The user documentation from ABB Robotics is divided into a number of categories.
This listing is based on the type of information in the documents, regardless of
whether the products are standard or optional.
All documents listed can be ordered from ABB on a DVD. The documents listed
are valid for IRC5 robot systems.
Product manuals
Manipulators, controllers, DressPack/SpotPack, and most other hardware is
delivered with a Product manual that generally contains:
• Safety information.
• Installation and commissioning (descriptions of mechanical installation or
electrical connections).
• Maintenance (descriptions of all required preventive maintenance procedures
including intervals and expected life time of parts).
• Repair (descriptions of all recommended repair procedures including spare
parts).
• Calibration.
• Decommissioning.
• Reference information (safety standards, unit conversions, screw joints, lists
of tools).
• Spare parts list with exploded views (or references to separate spare parts
lists).
• Circuit diagrams (or references to circuit diagrams).
Technical reference manuals

The technical reference manuals describe reference information for robotics
products.
• Technical reference manual - Lubrication in gearboxes: Description of types
and volumes of lubrication for the manipulator gearboxes.
• Technical reference manual - RAPID overview: An overview of the RAPID
programming language.
• Technical reference manual - RAPID Instructions, Functions and Data types:
Description and syntax for all RAPID instructions, functions, and data types.
• Technical reference manual - RAPID kernel: A formal description of the
RAPID programming language.
• Technical reference manual - System parameters: Description of system
parameters and configuration workflows.

Continued
Application manuals
Specific applications (for example software or hardware options) are described in
Application manuals. An application manual can describe one or several
applications.
An application manual generally contains information about:
• The purpose of the application (what it does and when it is useful).
• What is included (for example cables, I/O boards, RAPID instructions, system
parameters, DVD with PC software).
• How to install included or required hardware.
• How to use the application.
• Examples of how to use the application.
Operating manuals
The operating manuals describe hands-on handling of the products. The manuals
are aimed at those having first-hand operational contact with the product, that is
production cell operators, programmers, and troubleshooters.
The group of manuals includes (among others):
• Operating manual - Emergency safety information
• Operating manual - General safety information
• Operating manual - Getting started, IRC5 and RobotStudio
• Operating manual - IRC5 Integrator's guide
• Operating manual - IRC5 with FlexPendant
• Operating manual - RobotStudio
• Operating manual - Troubleshooting IRC5

Network security
Network security
Network security
This product is designed to be connected to and to communicate information and
data via a network interface, It is your sole responsibility to provide and continuously
ensure a secure connection between the product and to your network or any other
network (as the case may be). You shall establish and maintain any appropriate
measures (such as but not limited to the installation of firewalls, application of
authentication measures, encryption of data, installation of anti-virus programs,
etc) to protect the product, the network, its system and the interface against any
kind of security breaches, unauthorized access, interference, intrusion, leakage
and/or theft of data or information. ABB Ltd and its entities are not liable for
damages and/or losses related to such security breaches, any unauthorized access,
interference, intrusion, leakage and/or theft of data or information.

1 Safety
1.1 Introduction to safety information
1 Safety
1.1 Introduction to safety information
Overview
The safety information in this manual is divided into the following categories:
• General safety aspects, important to attend to before performing any service
or installation work on the controller. These are applicable for all service
work and are found in section General safety information on page 16.
• Safety signals and symbols shown in the manual and on the controller,
warning for different types of dangers, are found in Safety signals and
symbols on page 27.
• Specific safety information, pointed out in the procedure at the moment of
the danger. How to avoid and eliminate the danger is either detailed directly
in the procedure, or further detailed in separate instructions, found in section
Safety related instructions on page 33.

1 Safety
1.2.1 Introduction to general safety information
1.2 General safety information
1.2.1 Introduction to general safety information
Definitions
This section details general safety information for personnel performing installation,
maintenance and repair work.
Sections
The general safety information is divided into the following sections.
Section Examples of content
Safety in the robot system on page 17 This section describes the following:
• safety, service
• limitation of liability
• related information
Protective stop and emergency stop on This section describes protective stop and
page 19 emergency stop.
Safety risks on page 21 This section lists dangers relevant when work-
ing with the product. The dangers are split into
different categories.
• safety risks during installation or service
• risks associated with live electrical parts
Safety actions on page 23 This section describes actions which may be
taken to remedy or avoid dangers.
• fire extinguishing
• safe use of the teach pendant or jogging
device

1 Safety
1.2.2 Safety in the robot system
Validity and responsibility

The information does not cover how to design, install and operate a complete
system, nor does it cover all peripheral equipment that can influence the safety of
the entire system. To protect personnel, the complete system must be designed
and installed in accordance with the safety requirements set forth in the standards
and regulations of the country where the robot is installed.
The users of ABB industrial robots are responsible for ensuring that the applicable
safety laws and regulations in the country concerned are observed and that the
safety devices necessary to protect people working with the robot system are
designed and installed correctly. Personnel working with robot must be familiar
with the operation and handling of the industrial robot as described in the applicable
documents, for example:
• Operating manual - IRC5 with FlexPendant
I
• Operating manual - General safety information
• Product manual
I This manual contains all safety instructions from the product manuals for the robots and the
controllers.
The robot system shall be designed and constructed in such a way as to allow safe
access to all areas where intervention is necessary during operation, adjustment,
and maintenance.
Where it is necessary to perform tasks within the safeguarded space there shall
be safe and adequate access to the task locations.
Users shall not be exposed to hazards, including slipping, tripping, and falling
hazards.
Connection of external safety devices

Apart from the built-in safety functions, the robot is also supplied with an interface
for the connection of external safety devices. An external safety function can
interact with other machines and peripheral equipment via this interface. This
means that control signals can act on safety signals received from the peripheral
equipment as well as from the robot.
Limitation of liability
Any information given in this manual regarding safety must not be construed as a
warranty by ABB that the industrial robot will not cause injury or damage even if
all safety instructions are complied with.
Related information
Type of information Detailed in document Section

Installation of safety devices Product manual for the robot Installation and
commissioning
Changing operating modes Operating manual - IRC5 with FlexPend- Operating modes
ant

1 Safety
Continued
Type of information Detailed in document Section

Restricting the working space Product manual for the robot Installation and
commissioning
Load limits for tools and Product specification for the robot Load diagrams
workpieces
Configuration of safety mod- Application manual - Functional safety
ule (requires Functional safety and SafeMove
options)

1 Safety
1.2.3 Protective stop and emergency stop
Overview
Protective stops and emergency stops are defined by standards IEC 60204-1:2005
and EN ISO 10218-1:2011.
Stops can be in category 0 or category 1.
Stop category 0 As defined in IEC 60204, stopping by immediate removal of
power to the machine actuators (i.e. an uncontrolled stop. In
IRC5 this is implemented by removing power immediately in
the drive units.
Stop category 1 As defined in IEC 60204, a controlled stop with power available
to the machine actuators to achieve the stop and then removal
of power when the stop is achieved. In IRC5 this is implemented
by removing power in the drive units after about 1 second using
the servos to stop the machine.
Inputs to initiate a protective stop or an emergency stop

There are several safety inputs available to initiate a protective stop or an
emergency stop. All these safety inputs are of structure category 3 as described
in EN ISO 13849-1.
These safety inputs will initiate a stop of category 0 or category 1.
Safety inputs to initiate a Description
stop
Protective stop in automat- The safety input Automatic Stop is only operational in automatic
ic mode mode.
The default configuration is stop category 1.
Protective stop in automat- There are two safety inputs to initiate a protective stop in both
ic and manual mode automatic and manual mode. It is the safety input General Stop
and the safety input Superior Stop.
Emergency stop The Emergency Stop is operational in both automatic and
manual mode.
To modify the configuration of the stop category, see Technical reference

manual - System parameters.
Protective stop
Protective stops are activated through the dedicated safety inputs Automatic Stop,
General Stop, and Superior Stop, on the controller. For example, the protective
inputs are connected to safety outputs of presence sensing devices. This is to
provide safeguarding.
See Installation and commissioning in Product manual - IRC5.

1 Safety
Continued
Emergency stop
The emergency stop function shall not be applied as a substitute for safeguarding
measures and other safety functions but should be designed for use as a
complementary protective measure. (See ISO 13850.)
Note
Emergency stop must not be used for protective stop or program stop as this
causes extra, unnecessary wear on the robot.
For how to perform program stops, see section Stopping programs in Operating
manual - IRC5 with FlexPendant.
Depending on selected options for the robot, the number of emergency stops can
vary. See documentation for the robot and the complete machine.
Other methods to stop the robot

There are also other methods to stop the robot. See:
• Installation and commissioning in Product manual - IRC5
• Technical reference manual - System parameters
• Technical reference manual - RAPID Instructions, Functions and Data types.

1 Safety
1.2.4.1 Risks associated with live electric parts
1.2.4 Safety risks
Voltage related risks, general

Work on the electrical equipment of the robot must be performed by a qualified
electrician in accordance with electrical regulations.
• Although troubleshooting may, on occasion, need to be carried out while the
power supply is turned on, the robot must be turned off (by setting the main
switch to OFF) when repairing faults, disconnecting electric leads and
disconnecting or connecting units.
• The main supply to the robot must be connected in such a way that it can
be turned off from outside the working space of the robot.
• Make sure that no one else can turn on the power to the controller and robot
while you are working with the system. A good method is to always lock the
main switch on the controller cabinet with a safety lock.
The necessary protection for the electrical equipment and robot system during
construction, commissioning, and maintenance is guaranteed if the valid regulations
are followed.
All work must be performed:
• by qualified personnel
• on machine/robot system in deadlock
• in an isolated state, disconnected from power supply, and protected against
reconnection.
Voltage related risks, IRC5 controller

A danger of high voltage is associated with, for example, the following parts:
• Be aware of stored electrical energy (DC link, Ultracapacitor bank unit) in
the controller.
• Units such as I/O modules, can be supplied with power from an external
source.
• The main supply/main switch
• The transformers
• The power unit
• The control power supply (230 VAC)
• The rectifier unit (262/400-480 VAC and 400/700 VDC. Note: capacitors!)
• The drive unit (400/700 VDC)
• The drive system power supply (230 VAC)
• The service outlets (115/230 VAC)
• The customer power supply (230 VAC)
• The power supply unit for additional tools, or special power supply units for
the machining process.

1 Safety
Continued
• The external voltage connected to the controller remains live even when the
robot is disconnected from the mains.
• Additional connections.
Voltage related risks, robot

A danger of low voltage is associated with the robot in:
• The power supply for the motors (up to 800 VDC).
• The user connections for tools or other parts of the installation (max. 230
VAC).
Voltage related risks, tools, material handling devices, etc.

Tools, material handling devices, etc., may be live even if the robot system is in
the OFF position. Power supply cables which are in motion during the working
process may be damaged.

1 Safety
1.2.5.1 Fire extinguishing
1.2.5 Safety actions
1.2.5.1 Fire extinguishing
Note
Use a CARBON DIOXIDE (CO2) extinguisher in the event of a fire in the robot or
controller!

1 Safety
1.2.6 Safety data
1.2.6 Safety data
About this section

This chapter describes the necessary safety data required by standard EN ISO
13849-1:2015.
Prevailing directives and standards

For the use of industrial robots and how to protect personnel from being injured,
special regulations must be fulfilled as described in the following directives and
standards:
• Machinery Directive 2006/42/EC
• EN ISO 10218-1:2011
• EN ISO 13849-1:2008 (when explicitly called forth by EN ISO 10218-1:2011
as ISO 13849-1:2006)
• EN ISO 13849-1:2015
In addition to these standards covering general machinery safety, a number of
more specialized standards referred to as normative, must also be fulfilled. See
EN ISO 10218-1 chapter Normative references.
Performance level and category

EN ISO 13849-1, which is a B-standard, describes the general concept of
performance level (PL) and category. Each machine or machinery is potentially
dangerous and can cause personal injury. Based on severity of injury and probability
of accident, when using the machine, a certain level of safety performance, so
called required performance level (PLr) can be defined, where level a represents
the lowest risk and level e the highest. According to this, the machine must be
equipped with safety related parts, meeting the required performance level, to
reduce the risk to accepted low level. As specified in EN ISO 10218-1, normally
PL d is required for robots, but depending on the applications a higher requirement
could be needed if a risk analysis will result in PL e.
To comply with a certain PLr, in this case d, the safety related parts of the robots
and controllers must be structurally designed according to specific structure
categories and using reliable components.
In EN ISO 13849-1 it is in detail specified what category and components data,
which must be met, to fulfill PL d. These are:
• Category 3, which is normally fulfilled using double channels
• MTTFD (Mean Time To dangerous Failure) – high
• DC (Diagnostic Coverage) – low or medium
• CCF (Common Cause Failures) – better than 65 scores according to Annex
F
Performance level for ABB IRC5 controller

To verify that robots and controller comply with at least PL d a self assessment
has been carried out and documented in a Technical Report. The essential
conclusions are accounted for below.

1 Safety
1.2.6 Safety data
Continued
The safety related parts of robot and controller are e.g. the following stop circuits:
• Enabling device
• Emergency stop on operator panel
• Emergency stop on FlexPendant
• Limiting robot motion
• Protective stops
• SafeMove2
For the overall design and structure, the category 3 has been verified and meeting
the requirements of CCF.
Each of the stop circuits includes different components like enabling switch, panel
board, contactor board, relays etc. For each of these the MTTFD and DC have been
calculated according to EN ISO 13849-1 Annex C, D and E resulting in the values
as specified in the following table.
See the SISTEMA/ABB FSDT libraries for details of the safety functions.
IRC5C Compact
Safety function Calculated MTTFD DCavg

[years]
Emergency stop inputs 56 Medium
Automatic stop input 59 Medium
General stop input 59 Medium
Superior stop input 59 Medium
Limiting switch input 176 Medium
(without customer connection)
Three-position enabling device inputs 46 Medium
Emergency stop status outputs 263 Medium
SafeMove2 functions (option)
Protective stop category 0 52 Medium
Protective stop category 1 370 Low
Emergency stop category 0 52 Medium
Emergency stop category 1 370 Low
Emergency stop safe fieldbus output 160 Low
Speed supervision category 0 52 Medium
Speed supervision category 1 370 Low
Speed supervision safe fieldbus output 370 Low
Position supervision category 0 52 Medium
Position supervision category 1 370 Low
Position supervision safe fieldbus output 370 Low

1 Safety
1.2.6 Safety data
Continued
Based on the values from the previous table of MTTFD values, the corresponding
PFHD can be calculated using the Annex K, table K1 of EN ISO 13849-1:2008.
These are shown in the following table.
IRC5C Compact
Stop circuit Calculated PFHD PL

Emergency stop inputs 1.19x10E-07 d
Automatic stop input 1.03x10E-07 d
General stop input 1.03x10E-07 d
Superior stop input 1.03x10E-07 d
Limiting switch input 4.29x10E-08 e
(without customer connection)
Three-position enabling device inputs 1.54x10E-07 d
Emergency stop status outputs 4.29x10E-08 e
SafeMove2 functions (option)
Protective stop category 0 1.19x10E-07 d
Protective stop category 1 1.01x10E-07 d
Emergency stop category 0 1.19x10E-07 d
Emergency stop category 1 1.01x10E-07 d
Emergency stop safe fieldbus output 1.01x10E-07 d
Speed supervision category 0 1.19x10E-07 d
Speed supervision category 1 1.01x10E-07 d
Speed supervision safe fieldbus output 1.01x10E-07 d
Position supervision category 0 1.19x10E-07 d
Position supervision category 1 1.01x10E-07 d
Position supervision safe fieldbus output 1.01x10E-07 d
Conclusion according to EN ISO 13849-1:2015

The IRC5 controller safety system has a safety category 3 with performance level
PL d according to EN ISO 13849-1 using the simplified method of chapter 4.5.4 of
EN ISO 13849-1 and thus fulfils the safety performance requirement of the robot
safety standard EN ISO 10218-1.
The Common Cause Failure (CCF) is met according to the standard requirements.

1 Safety
1.3.1 Safety signals in the manual
1.3 Safety signals and symbols
Introduction to safety signals

This section specifies all dangers that can arise when doing the work described
in the user manuals. Each danger consists of:
• A caption specifying the danger level (DANGER, WARNING, or CAUTION)
and the type of danger.
• A brief description of what will happen if the operator/service personnel do
not eliminate the danger.
• Instruction about how to eliminate danger to simplify doing the work.
Danger levels
The table below defines the captions specifying the danger levels used throughout
this manual.
Symbol Designation Significance
DANGER Warns that an accident will occur if the instructions
are not followed, resulting in a serious or fatal injury
and/or severe damage to the product. It applies to
warnings that apply to danger with, for example,
contact with high voltage electrical units, explosion
xx0200000022
or fire risk, risk of poisonous gases, risk of crushing,
impact, fall from height, and so on.
WARNING Warns that an accident may occur if the instructions
are not followed that can lead to serious injury, pos-
sibly fatal, and/or great damage to the product. It
applies to warnings that apply to danger with, for
example, contact with high voltage electrical units,
xx0100000002 explosion or fire risk, risk of poisonous gases, risk
of crushing, impact, fall from height, etc.
ELECTRICAL Warns for electrical hazards which could result in
SHOCK severe personal injury or death.
xx0200000024
CAUTION Warns that an accident may occur if the instructions

are not followed that can result in injury and/or
damage to the product. It also applies to warnings
of risks that include burns, eye injury, skin injury,
hearing damage, crushing or slipping, tripping, im-
pact, fall from height, etc. Furthermore, it applies to
xx0100000003
warnings that include function requirements when
fitting and removing equipment where there is a risk
of damaging the product or causing a breakdown.
ELECTROSTATIC Warns for electrostatic hazards which could result
DISCHARGE (ESD) in severe damage to the product.
xx0200000023

1 Safety
Continued
Symbol Designation Significance

NOTE Describes important facts and conditions.
xx0100000004
TIP Describes where to find additional information or

how to do an operation in an easier way.
xx0100000098

1 Safety
1.3.2 Safety symbols on controller labels
Introduction to labels
This section describes safety symbols used on labels (stickers) on the controller.
Symbols are used in combinations on the labels, describing each specific warning.
The descriptions in this section are generic, the labels can contain additional
information such as values.
Note
The safety and health symbols on the labels on the product must be observed.
Additional safety information given by the system builder or integrator must also
be observed.
Types of labels
Both the manipulator and the controller are marked with several safety and
information labels, containing important information about the product. The
information is useful for all personnel handling the robot, for example during
installation, service, or operation.
The information labels can contain information in text (English, German, and
French).
Symbols on safety labels
Label Description
Electrical shock
xx1400001151
ESD sensitive components inside the controller.
xx1400001162
Disconnect power supply before servicing the controller.
xx1400001161
Disconnect power supply before servicing the controller (only

for welding equipment).
xx1400001160
Disconnect power supply before servicing the controller (for

controllers without UL mains switch).
xx1700000354

1 Safety
Continued
Label Description
High voltage inside the module even if the main switch is in
the OFF position.
xx1400001156
Lifting instruction for the IRC5 controller.
xx1400001157
Required installation space.
xx1400001155
QR code for ABB Basic Care service agreement.
xx1400001154

1 Safety
Continued
Label Description
Read the user manual before servicing.
xx1400001152
Electrical safety check of the robot system (internal).
xx1400001158
Functional test of the robot system (internal).
xx1400001159
Rating label
xx1400001163
UR certified (component)
xx1400002060

1 Safety
Continued
Label Description
UL certified (robot with controller)
xx1400002061
SafeMove label (for SafeMove Basic and SafeMove Advanced

software).
xx1700000355
Safety UL label (for the Functional Safety solution together

with UL mark).
xx1700000353

1 Safety
1.4.1 DANGER - Make sure that the main power has been switched off!
1.4 Safety related instructions
1.4.1 DANGER - Make sure that the main power has been switched off!
Description
Working with high voltage is potentially lethal. Persons subjected to high voltage
may suffer cardiac arrest, burn injuries, or other severe injuries. To avoid these
dangers, do not proceed working before eliminating the danger as detailed below.
Elimination, IRC5 Compact Controller
Action Note/illustration
1 Switch off the main power Note that the position of the main switch can vary depend-
switch on the controller ing on the year model.
cabinet.
A
xx0900000313
A: Main power switch

2 Disconnect the input power
cable from the wall socket.

1 Safety
1.4.2 WARNING - The unit is sensitive to ESD!
Description
ESD (electrostatic discharge) is the transfer of electrical static charge between two
bodies at different potentials, either through direct contact or through an induced
electrical field. When handling parts or their containers, personnel not grounded
may potentially transfer high static charges. This discharge may destroy sensitive
electronics.
Elimination
Action Note
1 Use a wrist strap. Wrist straps must be tested frequently to ensure
that they are not damaged and are operating cor-
rectly.
2 Use an ESD protective floor mat. The mat must be grounded through a current-limit-
ing resistor.
3 Use a dissipative table mat. The mat should provide a controlled discharge of
static voltages and must be grounded.

1 Safety
Continued
Location of wrist strap button

The location of the wrist strap button is shown in the following illustration.
IRC5 Compact Controller
xx1400001622
A Wrist strap button

1 Safety
1.4.3 CAUTION - Never stand on or use the cabinet as a ladder
1.4.3 CAUTION - Never stand on or use the cabinet as a ladder
Description
To avoid personal injury or damaging the product, it is never allowed to stand on
the cabinet. Nor is it allowed to use the cabinet as a ladder.

1 Safety
1.4.4 CAUTION - Make sure that there are no loose screws or turnings
1.4.4 CAUTION - Make sure that there are no loose screws or turnings
Description
To avoid damaging the product, make sure that there are no loose screws, turnings
or other parts inside the cabinet after work has been performed.

1 Safety
1.4.5 CAUTION - Close the cabinet door
1.4.5 CAUTION - Close the cabinet door
Description
The cabinet door must be closed properly when the robot system is in production.
If a door is not properly closed, the cabinet does not comply with the protection
class IP54 or IP20. The shield for Electro Magnetic Compatibility is also affected
if the door is not properly closed.
Note
To comply with IP54 all openings to the controller cabinet must be covered. This
includes unconnected connectors which must be fitted with covers.

1 Safety
1.4.6 CAUTION - Hot components in controller
1.4.6 CAUTION - Hot components in controller
Description
Units and heat sinks are HOT after running the robot!
Touching the units and heat sinks may result in burns!
With higher environment temperature more surfaces on the controller get HOT and
may result in burns.

1 Safety
1.4.7 CAUTION - Make sure that all mode selector keys are kept safe
1.4.7 CAUTION - Make sure that all mode selector keys are kept safe
Description
The key for the mode selector on the IRC5 controller is in standard designed to
work with all mode switches on all IRC5 controllers. It is the responsibility of the
robot system owner to make sure that all keys only are accessible to authorized
personnel, to prevent misuse.

1 Safety
1.4.8 Recover from emergency stops
1.4.8 Recover from emergency stops
Overview
Recovering from an emergency stop is a simple but important procedure. This
procedure ensures that the robot system is not returned to production while
maintaining a hazardous condition.
Reset the latch of emergency stop buttons

All push-button style emergency stop devices have a latching feature that must
be released in order to remove the emergency stop condition of the device.
In many cases this is done by twisting the push-button as marked, but there are
also devices where you pull the button to release the latch.
Reset automatic emergency stop devices

All automatic emergency stop devices also have some kind of latching feature that
must be released. Consult your plant or cell documentation to see how your robot
system is configured.
Recover from emergency stops
Action
1 Make sure the hazardous situation that resulted in the emergency stop condition no
longer exists.
2 Locate and reset the device or devices that gave the emergency stop condition.
3 Press the Motors On button to recover from the emergency stop condition.

2 Installation and commissioning
2.1 Overview

2.1 Overview
General
The IRC5 Compact controller has all components in one small cabinet. Note that
the appearance of the enclosure of the compact controller may vary depending on
year model.
xx0900000316
Note
When replacing a unit in the controller, report the following data to ABB, for both
the replaced unit and the replacement unit:
• the serial number
• article number
• revision
This is particularly important for the safety equipment to maintain the safety
integrity of the installation.

2.2 Installation activities
2.2 Installation activities
Prerequisites
The following section details the main steps on how to unload, transport, install
and connect the IRC5 Compact controller.
Overview of the installation
Action Information
1 Unpack the delivered IRC5 Compact con- How to unpack, store and transport the
troller. IRC5 Compact controller is described in
section Unpacking the controller on
page 45.
2 Install the IRC5 Compact controller. How to install the IRC5 Compact controller
is described in section On-site installation
on page 47.
3 Connect the manipulator to the IRC5 How to connect the manipulator to the
Compact controller. IRC5 Compact controller is described in
section Connecting cables to the controller
on page 63.
4 Connect power supply to the IRC5 Com- How to connect power supply is described
pact controller. in section Connecting power supply on
page 71.
5 Connect the FlexPendant to the IRC5 How to connect the FlexPendant is de-
Compact controller. scribed in section Connecting a FlexPend-
ant on page 57.
6 Miscellaneous connections. How to connect MOTORS ON/MOTORS
OFF circuits is described in section The
MOTORS ON/MOTORS OFF circuit on
page 80.
How to connect buses, for example Devi-
ceNet, is described in the Application
manual for the respective bus.
How to connect I/O units to the IRC5
Compact controller is described in the Ap-
plication manual for the respective I/O unit.
How to connect a PC to the controller is
described in manual Operating manual - Ro-
botStudio .
How to connect to a network is detailed in
section Connectors on the computer unit
on page 58.

2.3 Unpacking the controller
General
Before unpacking and installing the robot system, read the safety regulations and
other instructions very carefully. These are found in Chapter Safety on page 15.
The installation must be done by qualified installation personnel and should conform
to all national and local codes.
When unpacking the controller, check that it was not damaged during transport.
Note
If the controller is going to be stored before unpacking and installation, read the
following information regarding storage conditions.
Storage conditions
The table below shows the recommended storage conditions for the IRC5 controller:
Parameter Value
Min. ambient temperature -25°C (-13°F)
Max. ambient temperature +55°C (+131°F)
Max. ambient temperature (short periods, +70°C (+158°F)
max 24 h)
Max. ambient humidity Maximum 95% at constant temperature.
After storage, the operating conditions must be met for at least 4 hours before
switching on the controller (see Operating conditions on page 45 below).
Operating conditions
The table below shows the allowed operating conditions for the IRC5 controller:
Parameter Value
Min. ambient temperature 0°C (32°F)
Max. ambient temperature +45°C (113°F)
Max. ambient humidity Maximum 95% at constant temperature.
Weight of controller
The table below shows the weight for the IRC5 controller:
Controller Part Weight
IRC5 Compact Complete controller max. 30 kg
Protection class
The table below shows the protection classes for the IRC5 controller and the
FlexPendant:
Equipment Protection class
IRC5 Compact controller IP20

Continued
Equipment Protection class

FlexPendant IP54

2.4.1 Required installation space
2.4 On-site installation
Dimensions
The following illustration shows the required installation space for the IRC5 Compact
controller.
50
mm
mm
10 0
55
0 mm mm
540
50
mm
xx1400001367
a) Not required if the controller is rack-mounted
• A free space of 50 mm on both left and right side of the controller is required
if the controller is mounted on desk (not rack-mounted).
• A free space of 100 mm on the back of the controller is required to ensure
proper cooling. Do not place customer cables over the fan cover on the back
of the controller (because this makes it difficult to inspect and it leads to
inefficient cooling).

Continued
The following illustration shows the dimension of the footprint of the IRC5 Compact
controller.
407 21
302
98,8
xx1400001366
• The feet should only be used for positioning, not for mounting or fastening.
Note
If the IRC5 Compact controller is to be installed in a rack, it must be fastened in

a way that prevents distortion of the controller cabinet. Preferably with angle
bars along the entire side edges of the controller cabinet.

2.4.2 Mounting the FlexPendant holder
Location
One possible placement of the FlexPendant holder is shown in the illustration
below, but it can also be placed at another location.
xx1400001368
Note
Do not position the FlexPendant holder so that it is an obstacle in the place of

work.
Required equipment
Equipment Art.no
FlexPendant holder For spare parts, see Miscellaneous parts
on page 212.

Continued
Mounting the FlexPendant holder

Use this procedure to mount the FlexPendant holder.
1 Remove the protective liner from the tape.
xx0500002546
2 Press the mounting plate with FlexPendant

holder against the surface where it should be
mounted.
Note
The surface must be clean and dry.
Note
For rack mounted IRC5 Compact, do not place the FlexPendant holder on top
of the rack. Find a solution where the FlexPendant is placed so that it cannot fall
to the floor from a high position.

2.4.3 Mounting the controller in a 19" cabinet
General
The IRC5 Compact controller is designed to fit in a 19" cabinet.
xx1400002112
Required equipment
Equipment Information
Mounting kit 3HAC052262-001
Standard toolkit The content is described in section
Standard toolkit, IRC5 on page 207.
Other tools and procedures may be required. See
references to these procedures in the step-by-
step instructions below.
Procedure
Use the following procedure to remove the axis computer.
Action Info/illustration
1 Remove the five feet from the cabinet.

Continued
2 Assemble the mounting brackets.
xx1400002159
3 Fit the right, left and middle mounting

brackets in the 19 inch cabinet.
xx1500000232
4 Insert the IRC5 Compact in the 19 inch cab-

inet so that the latches fit in the recesses in
the back of the mounting brackets. Fasten
the IRC5 Compact to the mounting brackets
with the attachment screws.
xx1400002160

2.5.1 Buttons and switches on the front panel
2.5 Buttons and switches
2.5.1 Buttons and switches on the front panel
Front panel controls

The following illustration describes the buttons and switches on the front panel of
the IRC5 Compact controller.
A B C D E
xx1400001369
A Main power switch

B Brake release button (under the cover) for IRB 120. The IRC5 Compact used
with other robots has no brake release button, only a blanking plug, since the
robot has a brake release button.
C Mode switch
D Motors on
E Emergency stop
The brake release button is described in section Brake release button on page 54.
The other buttons and switches are described in Operating manual - IRC5 with
FlexPendant.

2.5.1.1 Brake release button
2.5.1.1 Brake release button
Location
xx1400001620
A Brake release button (under the cover) for IRB 120.
IRB 120
An IRC5 Compact controller used with IRB 120 has a brake release button located
under a plastic cover. At power on state, open the cover and press the brake release
button to change the positions of the manipulator axes manually.
WARNING
Be very careful when releasing the brakes. The axes may fall immediately and
can cause damage or injury.
Other robots
An IRC5 Compact controller used with other robots than IRB 120 has no brake
release button, only a blanking plug. The brake release button is located on the
robot.

2.6.1.1 Connectors on the controller
2.6 Connections
2.6.1 Connectors on the IRC5 Compact controller
General
The following section describes the connectors on the front panel of the IRC5
Compact controller.
CAUTION
Always inspect the connector for dirt or damage before connecting it to the
controller. Clean or replace any damaged parts.
Connectors
The following details the connection interface on the IRC5 Compact.
xx1400001372
Description
A XS.4 FlexPendant connection

Continued
Description
B XS.1 Robot power connection
C XS.41 Additional axes SMB connection
D XS.2 Robot SMB connection
E XP.0 Mains connection

2.6.1.2 Connecting a FlexPendant
2.6.1.2 Connecting a FlexPendant
Location of FlexPendant connector

The FlexPendant connector on the Compact Controller is located on the front of
the controller.
CAUTION
xx1400001371
A FlexPendant connector
Connecting a FlexPendant
Action Information
1 Locate the FlexPendant socket connector The controller must be in manual mode.
on the controller or operator’s panel.
2 Plug in the FlexPendant cable connector.
3 Screw the connector lock ring firmly by
turning it clockwise.

2.6.1.3 Connectors on the computer unit
Overview of the computer unit

The following illustration shows an overview of the computer unit.
xx1300000608
X1 Power supply
X2 (yellow) Service (connection of PC).
X3 (green) LAN1 (connection of FlexPendant).
X4 LAN2 (connection of Ethernet based options).
X5 LAN3 (connection of Ethernet based options).
X6 WAN (connection to factory WAN).
X7 (blue) Panel unit
X9 (red) Axis computer
X10, X11 USB ports (4 ports)
Note
It is not supported to connect multiple ports of the main computer (X2 - X6) to
the same external switch, unless static VLAN isolation is applied on the external
switch.
Service port test middle

The service port is intended for service engineers and programmers connecting
directly to the controller with a PC.

Continued
The service port is configured with a fixed IP-address, which is the same for all
controllers and cannot be changed, and has a DHCP server that automatically
assigns an IP-address to the connected PC.
Note
For more information about connecting a PC to the service port, see section
Working online in Operating manual - RobotStudio.
WAN port
The WAN port is a public network interface to the controller, typically connected
to the factory network with a public IP address provided by the network
administrator.
The WAN port can be configured with fixed IP-address, or DCHP, from the Boot
application on the FlexPendant. By default the IP-address is blank.
Some network services, like FTP and RobotStudio, are enabled by default. Other
services are enabled by the respective RobotWare application.
Note
The WAN port cannot use any of the following IP-addresses which are allocated
for other functions on the IRC5 controller:
• 192.168.125.0 - 255
• 192.168.126.0 - 255
• 192.168.127.0 - 255
• 192.168.128.0 - 255
• 192.168.129.0 - 255
• 192.168.130.0 - 255
The WAN port cannot be on a subnet which overlaps with any of the above
reserved IP-addresses. If a subnet mask in the class B range has to be used,
then a private address of class B must be used to avoid any overlapping. Please
contact your local network administrator regarding network overlapping.
See the section about topic Communication in Technical reference
manual - System parameters.
Note
For more information about connecting a PC to the WAN port, see section Working
online in Operating manual - RobotStudio.
LAN ports
The LAN 1 port is dedicated for connecting the FlexPendant.
The LAN 2 and LAN 3 ports are intended for connecting network based process
equipment to the controller. For example field buses, cameras, and welding
equipment.

Continued
LAN 2 can only be used as private network to the IRC5 controller.
Isolated LAN 3 or LAN 3 as part of the private network (only for RobotWare 6.01 and later)
The default configuration is that LAN 3 is configured as an isolated network. This
allows LAN 3 to be connected to an external network, including other robot
controllers. The isolated LAN 3 network has the same address limitations as the
WAN network.
Robot Controller
Private Isolated Public

LAN 3
Service LAN 1 LAN 2 LAN 3 WAN
xx1500000393
An alternative configuration is that LAN 3 is part of the private network. The ports
Service, LAN 1, LAN 2, and LAN 3 then belong to the same network and act just
as different ports on the same switch. This is configured by changing the system
parameter Interface, in topic Communication and type Static VLAN, from "LAN 3"
to "LAN". See Technical reference manual - System parameters.
Robot Controller
Private Public
Service LAN 1 LAN 2 LAN 3 WAN
xx1500000394
Note
For more information and examples of connecting to different networks, see

Application manual - EtherNet/IP Scanner/Adapter or Application
manual - PROFINET Controller/Device.
USB ports
The USB ports are intended for connecting USB memory devices.
Note
It is recommended to use the USB ports USB 1 and USB 2 on the X10 connector
for connecting USB memory devices.
The USB ports on the X11 connector are intended for internal use.

2.6.1.4 Connecting a serial channel to the controller
General
The serial channel is an option. To be able to connect a serial channel to the
controller, the main computer needs to be equipped with the expansion board
DSQC1003.
The expansion board has one RS232 serial channel, COM1, which can be used to
communicate with process equipment.
The expansion board also enables the connection of a fieldbus adapter. For more
information on how to connect a fieldbus adapter, see Definition of fieldbuses,
IRC5 on page 94.
Location
The serial channel connector is located on the expansion board in the computer
unit as shown below.
A B
xx1300000610
A COM1
B CONSOLE
Note
The CONSOLE connector is used for debugging purposes only.

Continued
Conversion of the RS232 channel

The RS232 channel can be converted to RS422 full duplex with an optional adapter,
DSQC 615.
The RS422 enables a more reliable point to point communication (differential) over
longer distances, from RS232 = 15m to RS422 = 120m.
Action Info/Illustration
1 Connect the adapter to the serial channel A cable is needed between the serial
connector. channel connector and the adapter.
xx1300000854
A cable
B adapter

2.6.2 Connecting cables to the controller
General
A good and proper electrical installation of the robot system is necessary to ensure
the best performance and prolong the lifetime of the whole robot system.
This section includes important information on how to connect cables and signals
to the controller.
Signal classes
Different rules apply to the different classes when selecting and laying cables.
Signals from different classes must not be mixed.
Signal class Description
Power signals Supplies external motors and brakes.
Class 4 (noisy) Applies to the cables associated with the power inputs and outputs
of variable speed drives. Cables carrying strongly interfering signals
such as motor cables, DC-link load sharing, unsuppressed inductive
loads, DC motors, welding equipment, etc.
Control signals Digital operating and data signals (digital I/O, protective stop, etc.).
Class 3 (slightly Applies to cables carrying slightly interfering signals: AC power
noisy) supply (<1 kV), DC power (24 V), power to equipment with RFI/EMI
filters, control circuits with resistive or suppressed inductive loads
(such as contactors and solenoids), direct-on-line induction motors,
etc.
Measuring signals Analog measuring and control signals (resolver and analog I/O).
Class 2 (slightly sens- This class covers ordinary analogue signals such as analogue sig-
itive) nals (4-20 mA, 0-10V, or signals below 1 MHz), low-speed digital
signals (RS232, RS485), digital (on/off) signals, limit switches, en-
coders, etc.
Data communication Gateway (fieldbus) connection, computer link.
signals Applies to cables carrying very sensitive signals. Signals with a full-
Class 1 (sensitive) scale range less than 1 V or 1 mA, and/or a source impedance >1
kOhm, and/or a signal frequency >1 Mhz. For example high-speed
digital communication (Ethernet), thermocouples, thermistors, strain
gauges and flowmeters.
Selecting cables
All cables laid in the control cabinet must be capable of withstanding 70°C. In
addition, the following rules apply to the cables of certain signal classes:
Signal class Cable type
Power signals Shielded cable with an area of at least 0.75 mm² or AWG 18.
Control signals Shielded cable.
Measuring signals Shielded cable with twisted pair conductors.
Data communication Shielded cable with twisted pair conductors. A specific cable
signals should be used for field bus connections and Ethernet, according
to the standard specification of the respective bus.

Continued
Note
Any local standards and regulations concerning insulation and area must always
be complied with.
Route the cables

Routing of cables shall be done in a professional way.
• Cables of different classes, such as signal cables and power cables, must
not be routed together as the power cables may introduce noise in the signal
cables. The greater the separation distance, the lesser the risk for interference
between the cables.
• Robot controller mains supply input cable and robot power cable should be
separated even though they belong to the same class.
• If crossing cables from different classes, cables should cross at an angle
close to 90 degrees.
• All external cables that are to be connected inside the controller must be
shielded in the chassis before entering the cabinet.
Separation distances can be reduced if e.g. dividers are used between cables
classes. Manufacturers of cable duct systems can provide information on how
reduced separation distances can be achieved using their specific products.
Signal class Cable type
Power signals • These signals generate a lot of interference and must be
laid separate from control, measuring, and communication
signals.
• The shielding must be connected to a paint-free part of the
panel chassis of the cabinet at both ends of the cable. Any
unshielded cable must be as short as possible.
• The manipulator power cables are routed on the floor and
along the left side of the controller cabinet.
• Cables should not be wound up like coils. This could cause
an magnetic field disturbing the signals. There would also
be a risk of overheating depending on the load.
Control signals • These signals are very sensitive to interference. To protect
these signals they should not be laid along with the power
Measuring signals signals.
Data communication • In the cable, each signal must be twisted with a neutral wire.
signals • The shielding must be connected directly to the chassis at
both ends of the cable.
Shielding cables
When peripheral devices are connected to the robot system, a shielded cable is
necessary to reduce coupling of the inner cable conductors to the environment
they pass through.
Shielding cable requirements

• The best method for shielding is to ground the shield at both ends of the
cable, provided the ends grounding are at the same potential.
• The optimum shielding is a combination of foil and braid screens.

Continued
• The best connection is one in which the shielding is extended up to and

makes a solid 360° connection (shown below) with the ground plane or
chassis.
Shielding example
The below example shows the shielding of a d-type connector:
xx1700001320
A A dimpled connector body makes multiple bonds to the mating connector

body all around its periphery, 360° bonding.
B Metal, or metallized, back shell makes 360° bond to the connector body.
C The cable shield is exposed and 360° clamped to the back shell. A tight fit
is a must.
Many other 360° bonding methods and types of 360° shielded connectors are also
acceptable.
Shield pigtail termination

Shield pigtail termination, as shown below, shall be avoided. If a pigtail connection
cannot be avoided, make it as short as possible.
xx1700001321
Ground and screen connections

The task of the grounding system is twofold - protective and functional. The primary
task is to serve as protective earth (PE) for personal and equipment safety. The
secondary task is to serve as a return path for common mode current.

Continued
For further information refer to EN 60204-1 and UL 1740.
Grounding requirements
The controller cabinet ground must come from the mains power supply PE.
• The cross-sectional area of each grounding (PE) conductor must be not less
than 2 mm 2 copper (AWG14) in the IRC5 Compact controller, and not less
than 10 mm 2 copper (AWG7) in the manipulator.
• The grounding cable color shall be green-yellow.
• The ground for the controller cabinet, robot manipulator and peripheral
devices must be the same, preferably an equipotential ground grid (mesh).
• Ground connection points must have stable inter-metallic bonding, like screw
fixation. Paint, dirt, rust, and other insulating material must be removed from
the contacting surfaces.
For requirements on the marking of the supply ground connection inside the control
cabinet refer to UL 508C. For further details on how grounding systems should be
designed refer to IEC 61000-5-2. For details of cross-sectional area of PE refer to
IEC 60204-1.
Grounding installation
For information on how to install the ground for the IRC5 Compact controller cabinet,
see Grounding on page 73.
For information on how to install the ground for the manipulator, see the
corresponding product manual.
Examples
The following figure shows 2 examples on how the ground and the signal cable
screens can be connected:
Control cabinet External unit
Example 1
Example 2
xx1200000960

Continued
Example 1:
• Where a good ground is available on all units, the best shielding is obtained
by grounding all screens at both ends on all units.
Example 2:
• If the cable is terminated where a good ground is not available a noise
suppression capacitor can be used. The screens of the 2 cables must be
connected as shown in the figure, but not connected to the chassis of the
unit.
Interference elimination
Internal relay coils and other units that can generate interference inside the control
cabinet are neutralized. External relay coils, solenoids and other units must be
clamped in a similar way. The illustration below shows how this can be done.
Note that the turn-off time for DC relays increases after neutralization, especially
if a diode is connected across the coil. Varistors give shorter turn-off times.
Neutralizing the coils lengthens the life of the switches that control them.
+24 V DC 0V
1)
2)
+24 V AC/DC 0V
3)
xx1200000961
1 The diode should be dimensioned for the same current as the relay coil, and
a voltage of twice the supply voltage.
2 The varistor should be dimensioned for the same energy as the relay coil,
and a voltage of twice the supply voltage.
3 When AC voltage is used, the components needs to be dimensioned for >500
V max voltage and 125 V nominal voltage.
The resistor should be 100 Ω, and the capacitor should be 1W 0.1 - 1 µF
(typically 0.47 µF).

2.6.3 Power supply system requirements
Definition of the power supply system

IEC 60364 defines three different types of mains grounding using the two-letter
codes. These are TN, TT, and IT.
First letter Type of ground connection
T Direct connection of one point to ground.
I Not connected to ground or connected to ground via a high impedance.
Second letter Connection between ground and the device being supplied
T Direct connection of one point to ground.
N Direct connection to neutral at the origin of installation, which is connec-
ted to the ground
In the following section the transformer configuration refers to the transformer

secondary side. Configuration of the transformer primary side is not discussed in
this context.
Recommended power supply systems

The following systems are recommended by ABB:
TN−S system TN−C system
PE and N are separate conductors that are A combined PEN conductor is used as both
connected together only near the transformer. a PE and an N conductor.
L1 L1
L2 L2
L3 L3
N PEN
PE
xx1700001311
xx1700001310
Not recommended power supply systems

The following systems are not recommended by ABB:
TT system (separate ground rods) Resistance grounded secondary system
If this kind of system must be used, the If this kind of system must be used, the
grounding path resistance between ground voltage variations between any line and PE
1 and 2 shall not exceed 0.1 Ohm, for more should not exceed ±10% of the nominal line
information refer to UL1740. voltage, for more information refer to EN
50160.

Continued
TT system (separate ground rods) Resistance grounded secondary system

L1 L1
L2 L2
L3 L3
N N
xx1700001312 xx1700001313
Not allowed power supply systems

The following systems are not allowed by ABB:
Un-symmetric system IT system (ungrounded secondary)
These transformers provide un-symmetric The voltage between phases and ground is
phase voltages with respect to ground. Inher- undefined and may cause damage to both
ent phase imbalances with respect to ground drive system and mains line filter (if installed).
would put the drive system and mains line
filter (if installed) under unacceptable stress.
L1
L2
L3
xx1700001316
xx1700001317
xx1700001315
xx1700001314
Isolation transformer
A three-phase isolation transformer between the mains supply and the control
cabinet is required for any of the below conditions:
• Not allowed power supply system used, as mentioned in Not allowed power
supply systems on page 69.
• When the mains supply is shared with a pressing machine, frequency
converter, or other large industry equipment that may cause the power supply
characteristics out of standard limits, see below.
• Mains power supply is out of standard limits, like voltage variations (+10%
to -15%), frequency variations (48.5 Hz to 61.8 Hz), harmonic (5%), voltage
unbalance (2%), voltage surge, voltage dips/swells, and so on.

Continued
For further information refer to regional power supply standards.
Allowed isolation transformer types

The following isolation transformer types are allowed by ABB:
Delta-Wye isolation transformer (△/Y) Wye-Wye isolation transformer (Y /Y)
xx1700001318 xx1700001319
A Primary/input
B Secondary/output
Mains line filter

A mains line filter is included in the IRC5 Compact controller.
A mains line filter in each robot cabinet is required for any of the below conditions:
• Robot system CE-labelling is required.
• Robot system will be installed in an EU country.
• When the mains supply is shared with a pressing machine, frequency
converter, or other large industry equipment that may cause the power supply
characteristics out of standard limits, see below.
• Mains power supply is out of standard limits, like voltage variations (+10%
to -15%), frequency variations (48.5 Hz to 61.8 Hz), harmonic (5%), voltage
unbalance (2%), voltage surge, voltage dips/swells, and so on.
Other types of external filters may be used, provided they are approved by regional
standards. For further information refer to regional power supply standards.

2.6.4 Connecting power supply
Note
How to manufacture a cable with connector is described in section Fitting the

connector on page 74.
CAUTION
Location
The following illustration shows the location of the power input connector on the
front panel of the controller.
xx1400001372
Description
A XS.4 FlexPendant connection
B XS.1 Robot power connection
C XS.41 Additional axes SMB connection

Continued
Description
D XS.2 Robot SMB connection
E XP.0 Mains connection
Required equipment
Equipment Note
Power supply cable (single phase)
External circuit breaker 16A
External earth fault protection at control cables 3 -15m 30mA
External earth fault protection at control cables >15m 300mA
Circuit diagram See Circuit diagrams on page 217.
Connecting power to the controller

The following procedure describes how to connect the mains power to the controller.
Action
1 Connect the power cable from the power supply to connector XP0 on the front panel
of the controller.

2.6.5 Grounding
2.6.5 Grounding
Location
Note
The whole cabinet ground is connected to the XP0.PE point.
2 1
A
5
xx1700000507
Description
A XP0.1 Power lline
B XP0.PE Grounding
C XP0.2 Zero line
Required equipment
Equipment Note
Mains connection cable (single phase)
Connecting ground controller

The following procedure describes how to connect the mains power to the controller.
Action
1 Connect single-phase power supply and PE wire to the XP0 connector.

2.6.6 Fitting the connector
General
This section describes how to manufacture a cable for connecting the mains power
to the controller.
Specifications
The following describes the cable and fuse requirements for the mains power
connection to the IRC5 Compact controller.
Component Description
Cable type Flexible oil resistant rubber
Cable area 3 x 2.5 mm 2
Fuse Delay action fuse 16A
Included parts
The following parts are included in the delivery.
Part Recommended supplier Order number Quantity
Hood Harting, 19 20 003 1640 3HAC051426-001 1
Female insert Harting, 09 12 005 2733 3HAC037697-001 1
Cable gland Harting, 19 00 000 5184 3HAC034913-001 1
Procedure
Use the following procedure to fit the connectors.
1 Select a suitable single phase cable and earth cable, See previous specifications.
and cut it to desired length.
2 Fit the cable through the cable gland and hood.
xx0900000365
• A: hood
• B: female insert
• C: cable gland

Continued
3 Connect the wires according to the illustration. Use a
screwdriver to make the contact tight.
xx0900000366
For single phase:

• X0.1 - power line
• X0.2 - zero line
• X0.PE - earth wire
4 Assemble the connector by fitting the hood and the
female connector, and tighten the screws.

2.6.7 Descriptions for connectors XS7 - XS17
XS7, XS8 and XS9 Safety
XS7 XS8 XS9
xx1500002927
These connectors is internally connected with safety board.

It contains the following signals:
• Auto stop
• General stop
• External emergency stop PB
• External supply
• External PTC
For connection details, see circuit diagram for IRC5 Compact, see Circuit diagrams
on page 217.
Note
Safety male connectors are delivered with Compact controller. The bridge
connector can be bought from ABB (3HAC051190-001). If it is bought from the
manufacturer, see Circuit diagrams on page 217 for connection details.

Continued
XS12, XS13, XS14 and XS15 I/O
XS12
XS13
XS14
XS15
xx1500002926
The connectors are internally connected with the I/O unit (DSQC 652).
The connectors contain 16 digital input signals, 16 digital output signals, 24V and
0V for the outputs, and 0V for the inputs. Note that 24V and 0V needs external
power supply.
For connection details, see circuit diagram for IRC5 Compact, see Circuit diagrams
on page 217.
XS16 Power Supply
XS16
xx1500002928

Continued
This connector is internally connected with I/O unit (DSQC 652) and power
distribution unit.
It contains the following signals:
• 24V power supply
Note
Total customer usage for 24V power supply from XS16 must not exceed 6A.
For connection details, see circuit diagram for IRC5 Compact controller.
Note
Power male connector are delivered with Compact controller. The power
connector is included in the same cable as DeviceNet connector
(3HAC054250-001). The bridge connector is a part of the cable 3HAC049564-001.
XS17 DeviceNet
XS17
xx1500002929
This connector is internally connected with DeviceNet - master bus.

It contains a DeviceNet signal.
Note
DeviceNet male connectors are delivered with Compact controller. The DeviceNet
connector is included in the same cable as power connector (3HAC054250-001).
The bridge connector is a part of the cable 3HAC049564-001.

Continued
XS18 Profibus
XS18
xx1500002972
This connector is internally connected with Profibus - master bus.

It contains a Profibus signal.

2.6.8 The MOTORS ON/MOTORS OFF circuit
Outline diagram
The MOTORS ON/MOTORS OFF circuit is made up of two identical chains of
switches.
The diagram shows the available customer connections, AS, GS, and ES.
A E
B C C
D
G F
U
H &
P S
R T
K
M N
xx1600000280
A ES (emergency stop)
B LS (Limit switch)
C Solid state switches
D Contactor
E Mains
F Drive unit
G Second chain interlock
H GS (general mode safeguarded space stop)
K AS (Automatic mode safeguarded space stop)
L ED (FlexPendant three-position enabling device)
M Manual mode
N Automatic mode
O Operating mode selector
P RUN
R EN1
S EN2
T Motor

Continued
U SS (Input from, for example, SafeMove board)
Function of the MOTORS ON/MOTORS OFF circuit

The circuit monitors all safety related equipment and switches. If any of the switches
are opened, the MOTORS ON/MOTORS OFF circuit switches the power to Motors
Off.
As long as the two chains not are in an identical state, the robot will remain in
MOTORS OFF mode.
Connection of safety chains

The diagram below shows the dual channel safety chain.
The supply from internal 24V and 0 V is displayed. For external supply of GS and
AS check the circuit diagram.
X15.4
Opto SS1
X15.2 isol.
Opto GS1
isol.
Opto AS1
isol.
X15.5
Opto SS2
X15.3 isol.
Terminal Location
GS2
X5 A21
X15 A21
AS2
xx1600000281
Technical data per chain

Limit switch Load: 300 mV
Max. voltage drop: 1 V

Continued
Technical data per chain

External connectors Load: 10 mA
Max. voltage drop: 4 V
GS/AS load at 24 V 25 mA
GS/AS closed "1" >18 V
GS/AS open "0" <5V
External supply of GS/AS/SS Max. + 35 VDC
Min. - 35 VDC
GS/AS Filter time 2.0 ms 1 )
Max. potential in relation to the 300 V
cabinet earthing and other signal
groups.
Signal class Control signals
1) When connecting e.g. a Safety PLC to a safety stop, make sure that the safety
check pulses do not exceed 2.0 ms, otherwise a safety relay must be connected
in between. See illustration below.
Safety PLC
IRC5 Compact
Safety board (A21)
Safety relay
Contact X9
X9.30 (AS1+)
X9.31 (24 V)
X9.22 (AS2-)
X9.20 (0 V)
en0900000482

Continued
Connection of ES1/ES2 on panel unit

The diagram below shows the terminals for the emergency circuits.
The supply from internal 24V (X1:2/X2:6) and 0V (X1:6/X2:2) is displayed. For an
ext. supply, X1:1 / X2:5 is connected to ext. 24V, and X1:5 / X2:1 is connected to
ext. 0V.
A
24V 0V
B C D
X1:2 X1:1
X1:7
X1:8
X1:6 X1:5
24V
X1:4
E
24V
X1:2
X1:3
G
0V 24V
F
B C D
X2:2 X2:1
X2:7
X2:8
X2:6 X2:5
0V
X2:4
H
0V
X2:2
X2:3
J
xx1000001009
A Internal
B Ext stop
C FlexPendant
D Cabinet
E ES1 internal
F Run chain 1 top
G Internal
H ES2 internal

Continued
J Run chain 2 top
Technical data
External supply of ES relay 24 VDC ± 10% between terminals X1:3,
7 and X2:7, 3 respectively.
Note! In case of interference, the external
supply must be properly filtered.
Rated current per chain 40 mA
Max. potential in relation to the cabinet earthing 300 V
and other signal groups.
Signal class Control signals

2.6.9 Programmable stop functions
Stopping functions
There are different methods to stop the robot, in addition to manually initiated
stops.
• Stop with system input signals
• Stop with RAPID instructions
• Other stops
Stop category configuration

The stop category can be configured, see Technical reference manual - System
parameters.
Safety inputs System paramet- Description
er Function
Automatic Stop SoftAS SoftAS can be used to configure the protective stop
in automatic mode either as stop category 0 or cat-
egory 1. The default configuration is TRUE (stop cat-
egory 1).
General Stop SoftGS SoftGS can be used to configure the protective stop
in automatic and manual mode, either as stop category
0 or category 1. The default configuration is TRUE
(stop category 1).
Superior Stop SoftSS SoftSS can be used to configure the protective stop
in automatic and manual mode, either as stop category
0 or category 1. The default configuration is TRUE
(stop category 1).
Emergency Stop SoftES SoftES is used to configure the emergency stop in
automatic and manual mode. The default configuration
is FALSE (stop category 0).
Stop with system input signals

In the control system, it is possible to define system input signals to be set/reset
through different interactions, for example, through networks, I/O blocks, RobAPI,
etc. See Application manual - Controller software IRC5.
Pre-defined system input Description
Stop The RAPID program execution is stopped, and the manipulator
is stopped on path with no deviation. The RAPID program
cannot be started when this system input signal is high. This
stop is similar to a normal program stop using stop button on
the FlexPendant.
SoftStop This is a faster stop of the manipulator than Stop. This stop is
more stressing for the mechanics than normal stop, therefore
there might be a minor deviation on path.
QuickStop This is a faster stop of the manipulator than Stop and SoftStop.
This stop is more stressing for the mechanics than normal stop
or SoftStop, therefore there might be a deviation on path.
Stop at End of Cycle Stops the RAPID program when the complete program is ex-
ecuted, that means when the last instruction in the main routine
has been completed.

Continued
Pre-defined system input Description

Stop at End of Instruction Stops program execution after the current instruction is com-
pleted.
All of these stops are performed without using the brakes, and the power is never
disconnected. The program execution can be continued directly, for example by
activating a start signal.
Note
Only safety rated input signals are allowed to be used for safety.
Stop with RAPID instructions

There are several RAPID instructions available that stops the robot.
Instruction Description Arguments
SystemStopAction Stops all robots in all tasks imme- \Stop: similar to a normal pro-
diately. gram stop with stop button.
\StopBlock: as above, but to re-
start the PP has to be moved.
\Halt: this is like a category 0
stop, i.e. it will result in motors off
state, stop of program execution
and robot movements in all motion
tasks. The Motors on button must
be pressed before the program
execution can be restarted.
Stop The current move instruction will \NoRegain: the robot will not re-
be finished before the robot stops. turn to the stop point when restar-
A restart will continue the program ted, e.g. after having been jogged
execution. away.
\AllMoveTasks: all robots will be
stopped.
StopMove The current move instruction will \Quick: the stop will be a soft
be stopped immediately as a nor- stop on path, as described for
mal program stop but the program system input SoftStop, otherwise
execution will continue with the similar to a normal program stop.
next instruction. This is often used \AllMotionTasks: all robots will
in for example trap routines. be stopped.
BREAK The current move instruction and
the program execution will be
stopped immediately as a normal
program stop. A restart will contin-
ue the program execution.
EXIT The current move instruction and
the program execution will be
stopped immediately as a normal
program stop. After stop the Pro-
gram Pointer has to be reset to
Main.
EXITCYCLE The current move instruction and
program execution will be stopped
immediately. The Program Pointer
will be reset to Main and if running
mode is continuous, the program
will be restarted.

Continued
Instruction Description Arguments

SearchX Search instructions can be pro- \Stop: the robot will stop as fast
grammed with arguments to stop as possible. This stop is per-
the robot movement close to the formed by ramping down motion
point where a search hit was no- in each motor separate from each
ticed. The program execution will other, and as fast as possible.
continue with the next instruction. Since it will be without any coordin-
ation, the robot may slide off path
fairly much.
\PStop: the robot will stop like
after a normal program stop.
\SStop: the robot will stop on path
but quicker than a normal program
stop. This is similar to a system
input SoftStop.
\Sup: the robot will continue to the
ToPoint. If more than one search
hit is found, an error will be repor-
ted.
RAPID instructions valid for IRC5 are described in Technical reference

manual - RAPID Instructions, Functions and Data types.
Other unexpected stops
Type of stop Description

SysFail In the control system there is a surveillance and monitoring
function that can detect abnormal situations. In such cases a
stop will be initiated. The robot controller must be restarted.
Power fail In the control system there is a monitoring function that can
detect power failure. In such cases a stop will be initiated.
Stop at collision In the control system there is a monitoring function that can
detect collisions. In such cases a stop will be initiated.
WARNING
Special care must be taken when restarting a machine that is

stopped due to a collision. The robot might make a limited
movement when restarted.
WARNING
The revolution counters might need to be updated after a colli-

sion to ensure path accuracy.

2.6.10 Emergency stop output
2.6.10 Emergency stop output
Emergency stop output through safety relay

The safety board DSQC 400 does not have an emergency stop output. The
emergency stop output can be extended by adding one safety relay. The diagram
below shows the connection of a safety relay, type RT6 from Jokab Safety. ABB
Robotics does not offer the safety relay option. The safety relay can be purchased
from Jokab Safety or Pilz.
Note
The safety board DSQC 400E has an integrated emergency output connector
(X14). Therefore there is no need to use an external safety relay with this board.
For more information on the safety board, see Replacement of safety board on
page 128 and Controller system parts on page 209.
Safety relay on safety board DSQC 400

-A21
-X13
-LIM_2B / 12;7
-X12 24V FPU POWER
11;4 / -24V SYS 24V SYS 1
-LIM_2A / 12;7
Power distribution 24V PANEL
1 2
board 11;5 / -0V SYS 0V SYS -LIM_1B / 12;7
3
2 -LIM_1A / 12;7
24V PANEL
12;3 / -24V COOL 4
EXTERNAL 3
EMERGENCY 12;3 / -0V COOL
-S21.3 STOP PB 4 FPU
21 22 ES1 top XS7/X1 -X10 -209 AWG20 BU -ES FPU 1:A / 12;7
1 XS8/X2 5
11 12 ES2 top -211 AWG20 BU -ES FPU 2:A / 12;7
1 7
-212 AWG20 BU -ES FPU 2:B / 12;7
8
0V 0V -210 AWG20 BU -ES FPU 1:B / 12;7
24V Panel 2
2 24V PANEL 6
RunCh0V
RunCh+
EXTERNAL
EMERGENCY Run CH1 top
STOP OUTPUT Run CH2 top 3
-S21.3
X53 X1 X4 3 -X9
-237 AWG20 21 22
A1 S13 S14 S34 13 23 33 41 -238
3
AWG20
-233 AWG20 11 12
9
9 -234 AWG20
5
SAFETY -231 AWG20
11
RELAY -232 AWG20
6
Sep ES2:A RunCh0V -235 AWG20
12
Sep ES1:A 7 RunCh+ -236 AWG20
4
7
10
1
U U
Sep ES1:B
2 8
Sep ES2:B
8
ES2 bottom
JUMPER
JUMPER
ES1 bottom 5
5 -X11
0V
24V Panel 6
1
6
2
AWG24 -24V_Sig.ref. / 12;8
EXTERNAL BU
24V PANEL 3 -RS485+ / 12;8
SUPPLY WHBU
4 -RS485- / 12;8
A2 S23 S24 S44 14 24 34 42 0V 5
6
WHBN -0V_Sig.ref. / 12;8
ES1:int 7
-RunCh_0V
-RunCh+
-RCH2
-RCH1
4
8
ES2:int MAIN
4 COMPUTER
ES1 ES2
12;6 /
12;6 /
12;6 /
12;6 /
xx1100000556

2.7 Opening the IRC5 Compact controller
2.7 Opening the IRC5 Compact controller
Removing the controller cover
1
DANGER
Before commencing any work inside

the cabinet, please observe the
safety information in section
DANGER - Make sure that the main
power has been switched off! on
page 33.
2 Remove the attachment screws on

the cover.
xx1400001364
3 Push the cover towards the back of

controller to release it from the bend
of the front panel, and then pull up-
wards to remove it.

2.8.1 Drive functions, general
2.8 Drive system
2.8.1 Drive functions, general
General
The robot is powered by power electronics found in the IRC5 Compact controller.
Location of drive unit
xx1400001373
A Main Drive Unit
Replacing drive system parts

How to replace the drive unit is described in section Replacement of drive unit on
page 165.

2.9.1 Memory functions
2.9 Memory functions
2.9.1 Memory functions
General
The controller is fitted with an SD-card memory containing ABB Boot Application
software. The SD-card memory is located inside the computer unit.
For more information on how to replace the SD-card memory, see Replacement
of SD-card memory in computer unit on page 163.
Note
Only use SD-card memory supplied by ABB.
CAUTION
Reformatting the SD-card or modifying the disk partition can cause irreparable
boot-up problems.

2.9.2 Connecting a USB memory
Handling USB
Handling of USB memory is described in Operating manual - IRC5 with FlexPendant.
Location on FlexPendant
The location of the USB port on the FlexPendant is shown by the following
illustration:
A
xx0900000022
A USB port (located behind rubber cover)

Continued
Location on the controller

The location of the USB ports on the IRC5 Compact controller is shown by the
following illustration:
xx1400001376
A USB port 1 - 4

2.10.1 Definition of fieldbuses, IRC5
2.10 I/O system
General
The IRC5 Controller may be fitted with a number of different fieldbus adapters and
fieldbus master/slave boards.
In the standard form, no fieldbus is mounted to the controller.
Fieldbus master/slave boards

On the main computer unit there are slots available for installing a master/slave
board.
B
xx1600000536
A Slot for PCIexpress boards

B Slot for safety board (option SafeMove Pro or SafeMove Basic)
Following master/slave boards are available:

Description Art. no. Type designation
PROFIBUS Master PCIexpress 3HAC044872-001 DSQC1005
DeviceNet Master/Slave PCIexpress 3HAC043383-001 DSQC1006

Continued
Expansion board for fieldbus adapters

An expansion board needs to be installed to be able to fit a fieldbus adapter. On
top of the main computer unit, there is one slot available for installing the expansion
board.
The expansion board is also equipped with a serial channel. For more information
on how to connect to the serial channel, see Connecting a serial channel to the
controller on page 61.
xx1300000605
A Assembled expansion board for fieldbus adapters, without adapter.

AnybusCC / RS232 expansion 3HAC046408-001 DSQC1003
board

Continued
Fieldbus adapters
The fieldbus adapters are inserted into the expansion board on top of the main
computer unit. There is one slot available for installing a fieldbus adapter.
xx1300000604
A Slot for AnybusCC fieldbus adapters
Following fieldbus adapters are available:

AnybusCC DeviceNet slave 3HAC045973-001 DSQC1004
AnybusCC PROFIBUS slave 3HAC026840-001 DSQC 667
AnybusCC Ethernet/IP slave 3HAC027652-014 DSQC 669
AnybusCC PROFINET slave 3HAC031670-001 DSQC 688
References
For more information on how to install and configure the fieldbuses, see the
respective fieldbus manual:
Manual title Art. no.
Application manual - DeviceNet Master/Slave 3HAC050992-001
Application manual - DeviceNet Anybus Slave 3HAC050993-001
Application manual - EtherNet/IP Anybus Adapter 3HAC050997-001
Application manual - EtherNet/IP Scanner/Adapter 3HAC050998-001
Application manual - PROFIBUS Anybus Device 3HAC050965-001
Application manual - PROFIBUS Controller 3HAC050966-001
Application manual - PROFIenergy Device 3HAC050967-001

Continued
Manual title Art. no.

Application manual - PROFINET Anybus Device 3HAC050968-001
Application manual - PROFINET Controller/Device 3HAC050969-001

2.10.2 DeviceNet I/O units
2.10.2 DeviceNet I/O units
General
The IRC5 controller may be fitted with DeviceNet I/O or encoder units. These are
configured in an identical way.
Standard configuration
In the standard form, no fieldbus is mounted to the controller.
It is possible to connect any type of DeviceNet compliant I/O unit on the DeviceNet
- master bus. All I/O units should comply with the DeviceNet standard and be
conformance tested by ODVA.
DeviceNet I/O units and parts

The table below specifies the DeviceNet I/O units:
Description Note
Digital I/O DSQC 652
See Spare parts on page 209 for the spare part numbers.
Encoder interface units

The table below specifies the encoder interface units:
Description Art. no. Note
Encoder interface unit for conveyor 3HNE 01586-1 DSQC 377B
tracking
Further information
The table below gives references to additional information:
Information: Found in:
How to install the DeviceNet I/O Fit the expansion board and/or field bus adapter ac-
units mechanically and electrically. cording to Replacement of expansion board in the
computer unit on page 151 and/or Replacement of
fieldbus adapter in the computer unit on page 154.
Allowed configurations of Devi- Technical reference manual - System parameters
ceNet I/O units and how to setup
the configurations.
How to install the DeviceNet I/O unit The application manual for the different I/O buses re-
software related in a new system. spectively, see listing in Definition of fieldbuses, IRC5
on page 94.
Detailed descriptions of all available The application manual for the different I/O buses re-
DeviceNet I/O units. spectively, see listing in Definition of fieldbuses, IRC5
on page 94.

2.11.1 Installation of external operator's panel
2.11 Installation of add-ons
Location
An external operator's panel may be fitted in a separate wall cabinet as shown in
the illustration below.
D
C
E
B
F
A
G
I H
xx1000000954
A Wall cabinet
B Front panel
C Blanking plug for FlexPendant
D Blanking plug for actuator red
E Emergency stop button
F Motor ON button
G Mode switch
H External Operator's panel harness
I FlexPendant connector
Required equipment
Equipment Art. no. Note

Wall cabinet IRC5 3HAC038671-001
External Operator's panel 3HAC038672-001 7m
cable 3HAC038673-001 15 m
3HAC038674-001 30 m
Circuit diagram See Circuit diagrams on
page 217.

Continued
Procedure
The procedure below details how to install the external control panel.
1
DANGER
Before commencing any work inside the

cabinet, please observe the safety informa-
tion in section DANGER - Make sure that
the main power has been switched off! on
page 33.
2 Remove the cover of the cabinet. See Opening the IRC5 Compact controller
on page 89.
3 Remove the two attachment screws for the
safety board unit and gently pull it out a
little bit.
4 Remove the contactor unit (contactors at-
tached with plate) attachment screws and
move the unit leftwards a little bit.
5 Disconnect signal cabling from the safety
board.
Connectors: X9
• A21.X6
X6
• A21.X9
xx1500000114
6 Detach the Emergency stop button, Motor

on button and Mode switch together with
their cabling on the controller. Mount these
buttons and switch on the external operat-
or's panel and strap the cabling to the exist-
ing cable strapping behind the front panel.
7 Connect the round connector from the ex-
ternal operator's panel harness to XS4 on
the controller.

Continued
8 Fit the cable from the external operator's
panel harness to the controller through the
hole for Emergency stop button and tighten
the cable gland.
xx1000000956
9 Cover the holes for Motor on button and

Mode switch on the controller with a
blanking plug.
10 Connect the earth cable to the ground ter- A
minal inside the cabinet.
xx1400002803
• A: ground terminal
11 Connect the signal connectors Ext.A21.X6
and Ext.A21.X9 to the connector X6 and X9
on the safety board.
12 Strap the cables and secure the attach-
ments screws for contactor unit and safety
board unit.
13 Fit the external operator's panel harness to
the wall cabinet with four attachment
screws.
14 Connect the connectors and earth cable
inside the wall cabinet.
15 Mount the front panel of the external oper-
ator's panel on the wall cabinet with four
attachment screws.

2.11.2 Installation of external enabling device
Overview
IRC5 is delivered with one enabling device but have the possibility to connect one
additional external enabling device (cannot be ordered from ABB Robotics).
When an external enabling device is used together with the three-position enabling
device on the teach pendant, both enabling devices must be enabled to be able
to operate the manipulator in manual mode.
Connecting the external enabling device

The external enabling device must be connected to the safety board connector X6
pin 7-10 as shown in the figure below.
IRC5
Safety board (A21)
Connector X6
External enabling
X6.7 (EN1_1A)
device
X6.9 (EN2_1B)
X6.10 (EN2_1A)
X6.8 (EN1_1B)
xx1600000181
The enabling device chain is enabled if X6 pin 7 is short circuited with X6 pin 8 at
the same time as X6 pin 9 is short circuited with X6 pin 10.
Requirement on the external enabling device

The external enabling device connected to IRC5 must have the following
characteristics:
• Redundant channels.
• Three-position enabling device. When the enabling device is pressed to the
center position the enabling device chain must be enabled. When the enabling
device is released or pressed to third position, the enabling device chain
must be disabled.
• The enabling device must have a B10 value of at least 100000 cycles (less
than 10% chance of failure before 100000 cycles).
• The mean time to dangerous failure (MTTFd) of the external enabling device
must be high enough to ensure that the external enabling device together

Continued
with IRC5’s enabling device chain is above 55 years. See safety related
performance for the enabling device chain below.
Performance of IRC5 original enabling device chain

The safety-related performance of the enabling device chain, without the external
enabling device, is as follows:
• MTTFd for IRC5 enabling device chain is 80 years.
• IRC5’s enabling device chain’s calculated average probability of dangerous
failure per hour (PFHd) is 6.62x10E-08.
• IRC5’s enabling device chain’s design and structure is category 3.
• IRC5’s enabling device chain’s Diagnostic Coverage is medium (90% < DCavg
< 99%).
• The Common Cause Failure (CCF) is met according to the standard
requirements.

2.11.3 Installing the Safety module DSQC1015 for SafeMove
General
To use the options SafeMove Basic and SafeMove Pro you need to install the
Safety module DSQC1015 in the robot controller.
The procedure below describes how to install the Safety module and how to connect
the cables.
Location
The Safety module DSQC1015 is a PCIexpress board that is located inside the
IRC5 main computer unit.
xx1500001760
A Safety module DSQC1015

B PCIexpress slot for other devices.
Required equipment
Illustration of the cable harnesses are found in section:
• Connecting the cables to the Safety module (hardware switch and 731-1) on
page 107
Item Equipment Note

DSQC1015 Safety module 3HAC048858-001
A2 Harness safety hard Key switch 3HAC057074-001
D Harness 24 V I/O DSQC1015 3HAC057073-001
B Harness auxiliary contact 3HAC057076-001
E Harness Emergency stop 3HAC032324-001
F Harness Control (Motor on, Key switch) 3HAC049563-001

Continued
Item Equipment Note

G Harness extended Key switch 3HAC057075-001
Used when the controller has the option
735-3 or 735-4 Additional contacts.
Standard toolkit The contents are defined in section Stand-
ard toolkit, IRC5 on page 207.
Installing the Safety module
Action Note/Illustration
1
DANGER

cabinet, please observe the safety inform-
ation in section DANGER - Make sure that
page 33.
2
ELECTROSTATIC DISCHARGE
(ESD)
The unit is sensitive to ESD. Before hand-

ling the unit please observe the safety in-
formation in section WARNING - The unit
is sensitive to ESD! on page 34
3 Remove the cover of the cabinet. See Removing the controller cover on
page 89.
4 Remove the computer unit. See Replacement of computer unit on
page 138.
5 Open the computer unit by removing the
attachment screws and lift off the cover.
Disconnect the fan connector.
CAUTION
Be careful with the fan cable when opening

A
and removing the upper cover. The fan
B
cable must not be stretched.
xx1300000684
A Attachment screws (4 pcs.)

B Cover
6 Remove the attachment screw on top of
the slot bracket.

Continued
7 Fit the Safety module in position by push-
ing it into the socket on the motherboard.
A
B
xx1500001761
A Attachment screw
B Safety module
CAUTION
Always grip the board around the edges to

avoid damage to the board or its compon-
ents.
8 Refit the attachment screw on top of the

Safety module bracket.
9 Refit the fan connector and close the com-
puter unit.
CAUTION
Be careful with the fan cable when closing

the cover. The fan cable must not be
A
squeezed.
B
xx1300000684

B Cover
10 Connect all cables according to the proced-
ures described below.

Continued
Connecting the cables to the Safety module (hardware switch and 731-1)
This procedure describes how to connect the cables for a robot controller equipped
with the options Hardware switch and 731-1 Safety internal connection.
EM Stop
Safety Module
S21.3
A31.4
Motors On X6 XS1
S21.2 X3 G2
D EM Stop
Key Switch
XS/XP37 X9
E S21.3
S21.1 G A2 Motors On
X6
F
A21 S21.2
K42 K43
X14
Key Switch
X15
XS/XP38
B S21.1
Safety Board
xx1600000252
Action
1
DANGER
Before commencing any work inside the cabinet, read the safety information in
section DANGER - Make sure that the main power has been switched off! on page 33
2
WARNING
The unit is sensitive to ESD. Before handling the unit please read the safety inform-
ation in the section WARNING - The unit is sensitive to ESD! on page 34
3 Mount auxiliary contact harness contact blocks (B) on contactors K42 and K43.
4 Connect auxiliary contact harness (B) to safety hard Key switch harness (A2) at
connector XS/XP38.
5 Connect safety hard Key switch harness (A2) connector A31.4.X6 to Safety board
DSQC1015.
6 Connect connector A31.4.X1 on 24 V I/O harness (D) to safety board DSQC1015.
7 Connect connector G2.X3 on 24 V I/O harness (D) to power distribution unit (G2).
8 Connect safety hard Key switch harness (A2) connectors X14 and X15 to the panel
board (A21).
9 Connect extended Key switch harness (G) to safety hard Key switch harness (A2)
at connector XS/XP37.
10 Connect emergency stop harness (E) connector A21.X9 to the panel board.

Continued
Action
11 Connect emergency stop harness (E) connector S21.3 to Emergency Stop on the
control panel.
12 Connect the control harness (F) connector A21.X6 to the panel board.
13 Connect the control harness (F) connector S21.2 to Motors On on the control panel.
14 Connect the control harness (F) connector S21.1 to Key Switch on the control panel.
15 Route cables properly in existing cable holders.

2.12 Testing
Continued
2.12 Testing
Function tests
When the installation is complete, perform the function tests in section Function
tests on page 118 to verify that the safety features work properly.

3 Maintenance
3.1 Maintenance schedule, IRC5 Compact controller
3 Maintenance
3.1 Maintenance schedule, IRC5 Compact controller
General
The IRC5 Compact robot controller must be maintained at regular intervals to
ensure its function. The maintenance activities and their respective intervals are
specified below.
Intervals
Equipment Maintenance Interval Detailed in section:

activity
Complete controller Inspection 12 months i Inspecting the IRC5 Compact con-
troller on page 112
System fans Inspection 6 months i Inspecting the IRC5 Compact con-
troller on page 112
FlexPendant Cleaning When needed Cleaning the FlexPendant on
page 115
Emergency stop Function test 12 months Function test of emergency stop on
(operating panel) page 118
Emergency stop Function test 12 months Function test of emergency stop on
(FlexPendant) page 118
Mode switch Function test 12 months Function test of mode switch on
page 119
Enable device Function test 12 months Function test of three-position en-
abling device on page 120
Motor contactors Function test 12 months Function test of motor contactors
K42, K43 K42 and K43 on page 121
Brake contactor K44 Function test 12 months Function test of brake contactor
K44 on page 122
Auto stop (tested if Function test 12 months Function test of auto stop on
used) page 123
General stop (tested Function test 12 months Function test of general stop on
if used) page 124
Reduced speed Function test During commis- Function test of reduced speed
control sioning control on page 125.
i The interval depends on the working environment of the equipment: a cleaner environment may
extend the maintenance interval and vice versa.
Function test after replacement of component

In addition to performing the function tests according to the intervals, function tests
should be performed after replacing a component in the controller.

3 Maintenance
3.2.1 Inspection of controller
3.2 Inspection activities
3.2.1 Inspection of controller
Inspecting the IRC5 Compact controller

Use this procedure to inspect the IRC5 Compact controller.
1
DANGER
Before commencing any work inside the cabinet,

please observe the safety information in section
DANGER - Make sure that the main power has been
switched off! on page 33.
2
ELECTROSTATIC DISCHARGE (ESD)
The unit is sensitive to ESD. Before handling the

unit please read the safety information in the section
WARNING - The unit is sensitive to ESD! on page 34
3 Inspect connectors and cabling to make sure they

are securely fastened and cabling not damaged.
4 Inspect the system fans and ventilation holes on
the surface of the cabinet to make sure they are
clean.
A
xx1400001377
5 After cleaning: Temporarily turn the power supply

to the controller on. Inspect the fans to make sure
they function correctly. Turn the power supply back
off.

3 Maintenance
3.3.1 Activities
3.3 Changing/replacing activities
3.3.1 Activities
References
Certain activities to be performed as specified in the maintenance schedule are
not detailed in this chapter, but in the repair chapter. See Repair on page 127.

3 Maintenance
3.4.1 Cleaning of control cabinet
3.4 Cleaning activities
3.4.1 Cleaning of control cabinet
Required equipment
Equipment, etc. Note

Vacuum cleaner ESD protected
Internal cleaning
Clean the cabinet interior with an ESD protected vacuum cleaner, if necessary.
Do's and don'ts!

The section below specifies some special considerations when cleaning the
controller.
Always:
• use ESD Protection
• use cleaning equipment as specified above! Any other cleaning equipment
may shorten the life of paintwork, rust inhibitors, signs, or labels!
• check that all protective covers are fitted to the controller before cleaning!
Never:
• remove any covers or other protective devices when cleaning the outside of
the controller!
• use compressed air or spray with a high pressure cleaner!

3 Maintenance
3.4.2 Cleaning the FlexPendant
Location
The surfaces to clean are shown in the illustration below.
xx0400000973
A Touch screen
B Hard buttons
Required equipment
Equipment, etc. Note

Soft cloth ESD Protected
Warm water/Mild cleaning agent
Clean the touch screen

This section details how to clean the touch screen.
1 Before cleaning the screen, tap
Lock Screen on the ABB menu.
en0400001221

3 Maintenance
Continued
2 Tap the Lock button in the follow-
ing window.
en0400000657
3 When the next window appears, it

is safe to clean the screen.
en0400000658
4 Clean the touch screen and hard-

ware buttons using a soft cloth and
water or a mild cleaning agent.
5 To unlock the screen, follow the
instructions on the screen.
en0400000658
Do's and don'ts!

The section below specifies some special considerations when cleaning the
FlexPendant.
Always:
• use ESD Protection
3 Maintenance
Continued
• use cleaning equipment as specified above! Any other cleaning equipment

may shorten the life time of the touch screen.
• check that all protective covers are fitted to the device before cleaning.
• make sure that no foreign objects or liquids can penetrate into the device.
Never:
• remove any covers before cleaning the FlexPendant.
• spray with a high pressure cleaner.
• clean the device, operating panel and operating elements with compressed
air, solvents, scouring agent or scrubbing sponges.

3 Maintenance
3.5.1 Function test of emergency stop
3.5 Function tests
3.5.1 Function test of emergency stop
Overview
Perform this test on the emergency stop button both on the operating panel and
on the FlexPendant.
Performing the function test
Action Note
1 Make a visual inspection of the emergency If any damage is found on the emergency
stop button to make sure it is not physically stop button, it must be replaced.
damaged.
2 Start the robot system.
3 Press the emergency stop button. The test is passed if the event message
“10013 emergency stop state” appears in
the FlexPendant log.
If the event message “10013 emergency
stop state” does not appear or if the event
message “20223 Emergency stop conflict”
appears in the FlexPendant log, the test is
failed and the root cause of the failure must
be found.
4 After the test, release the emergency stop
button and press the motors on button to
reset the emergency stop state.

3 Maintenance
3.5.2 Function test of mode switch
3.5.2 Function test of mode switch
2-position mode switch
Action Note
2 Start with the mode switch in manual mode This test is passed if it is possible to run
and then switch the mode switch to auto the robot in auto mode.
mode. Run the robot in auto mode. If it is not possible to run the robot in auto
mode, this test is failed and the root cause
of the failure must be found.
3 Switch the mode switch to manual mode. This test is passed if the event message
“10015 Manual mode selected” appears in
If the event message “10015 Manual mode
selected” is not shown in the FlexPendant
log, the test failed and the root cause of
the failure must be found.
3-position mode switch
Action Note
2 Start with the mode switch in manual mode This test is passed if it is possible to run
and then switch the mode switch to auto the robot in auto mode.
mode. Run the robot in auto mode. If it is not possible to run the robot in auto
mode, this test is failed and the root cause
of the failure must be found.
3 Switch the mode switch to manual full This test is passed if it is possible to run
speed mode. Run the program in manual the program in manual full speed mode.
full speed mode. If it is not possible to run the program in
manual full speed mode, this test is failed
and the root cause of the failure must be
found.
4 Switch the mode switch to manual mode. This test is passed if the event message
“10015 Manual mode selected” appears in
If the event message “10015 Manual mode
selected” is not shown in the FlexPendant
log, the test failed and the root cause of

3 Maintenance
3.5.3 Function test of three-position enabling device
3.5.3 Function test of three-position enabling device
Action Note
1 Start the robot system and turn the mode
switch to manual mode.
2 Press the three-position enabling device This test is passed if the event message
to the middle position and then hold the "10011 Motors ON state" appears in the
enabling device in this position. FlexPendant log.
If the event message "10011 Motors ON
state" does not appear or if the event
message "20224 Enabling device conflict"
be found.
3 While still holding the three-position en- This test is passed if the event message
abling device pressed, press the enabling "10012 safety guard stop state" appears
device harder to the enable the device's in the FlexPendant log.
third position. If the event message "10012 safety guard
stop state" does not appear or if the event
message "20224 Enabling device conflict"
appears in the Flexpendant log, the test is
be found.

3 Maintenance
3.5.4 Function test of motor contactors K42 and K43
3.5.4 Function test of motor contactors K42 and K43
Action Note
2 Press the three-position enabling device This test is passed if the event message
to the middle position and then hold the "10011 Motors ON state" appears in the
enabling device in this position. FlexPendant log.
If the event message "37001 Motor on ac-
tivation error" appears on the FlexPendant
log, the test is failed and the root cause of
3 Release the three-position enabling device. This test is passed if the event message
"10012 safety guard stop state" appears
in the FlexPendant log.
If the event message "20227 Motor contact-
or conflict" appears in the FlexPendant
log, the test is failed and the root cause of

3 Maintenance
3.5.5 Function test of brake contactor K44
3.5.5 Function test of brake contactor K44
Action Note
2 Press the three-position enabling device This test is passed if the brakes is disen-
to the middle position and then hold the gaged and the manipulator can be moved.
enabling device in this position. If the Event message "50056 Joint colli-
While having eye contact with the manipu- sion" appears in the FlexPendant log, the
lator, move the joystick slightly in any dir- test is failed and the root cause of the fail-
ection to disengage the brakes. ure must be found.
3 Release the three-position enabling device This test is passed if the event message
to engage the brakes. "10012 safety guard stop state" appears
in the FlexPendant log.
If the event message "37101 Brake failure"
be found.

3 Maintenance
3.5.6 Function test of auto stop
3.5.6 Function test of auto stop
Action Note
switch to auto mode.
2 Activate the auto stop, e.g. by opening the The test is passed if the event message
connected robot cell door. “20205 Auto stop open” appears in the
FlexPendant log.
If the event message “20205 Auto stop
open” does not appear or if the event
message “20225 Auto stop conflict” ap-
pears in the Flexpendant log, the test is
be found.

3 Maintenance
3.5.7 Function test of general stop
3.5.7 Function test of general stop
Action Note
2 Activate the general stop. The test is passed if the event message
“20206 General stop open” appears in the
FlexPendant log.
If the event message “20206 General stop
open” does not appear or if the event
message “20226 General stop conflict”
appears in the Flexpendant log, the test is
be found.

3 Maintenance
3.5.8 Function test of reduced speed control
3.5.8 Function test of reduced speed control
Action Note
2 Create a test program where the robot The distance and speed must be adapted
moves along a known distance with a pro- to the current installation and robot model.
grammed speed higher than 250 mm/s.
3 Start the program in manual mode and This test is passed if the speed of the robot
measure the time it takes for the robot to does not exceed 250 mm/s, otherwise the
travel the distance. test is failed and the root cause of the fail-
ure must be found.
Tip
To get accurate results, use sensors or I/O

signals to measure the time.

4 Repair
4.1 Overview
4 Repair
4.1 Overview
Report replacements
When replacing a unit in the controller, report to ABB:
• the serial number
• article number
• revision
of both the replaced unit and the replacement unit.
This is particularly important for the safety equipment to maintain the safety integrity
of the installation.

4 Repair
4.2 Replacement of safety board
Location
The safety board is located as shown in the following illustration.
xx1400001378
A Safety board
Required equipment
Equipment Note
Safety board DSQC 400
See Controller system parts on page 209

4 Repair
Continued
Removal
Use the following procedure to remove the safety board.
1
DANGER

DANGER - Make sure that the main power has
been switched off! on page 33.
2

unit please read the safety information in the sec-
tion WARNING - The unit is sensitive to ESD! on
page 34
3 Remove the cover of the cabinet. See Opening the IRC5 Compact
4 Disconnect all connectors. Make a note of all connections.
5 Remove the thumb screw and open the protective
cover on the front of the cabinet.
6 Disconnect three customer connectors.
xx1400002007
7 Remove the four attachment screws to remove the A B

protection cover.
xx1400001379

4 Repair
Continued
8 Remove the eight attachment screws.
xx1400001380
9 Gently lift the safety board out.
Refitting
Use the following procedure to refit the safety board.
Note
Always grip the board around the edges to avoid damage to the board or its
components.
Action
1
DANGER
Before commencing any work inside the cabinet, please observe the safety information
in section DANGER - Make sure that the main power has been switched off! on page 33.
2
The unit is sensitive to ESD. Before handling the unit please observe the safety inform-
ation in section WARNING - The unit is sensitive to ESD! on page 34
3 Gently lift the safety board out of the ESD safe bag and fit it into position on the safety
board plate.
4 Secure the safety board with its attachment screws.
5 Refit the safety board unit protection cover.
6 Reconnect all connectors.
7 Refit the cabinet cover.
8 Perform the function tests in section Function tests on page 118 to verify that the safety
features work properly.

4 Repair
4.3 Replacement of I/O unit
General
An I/O unit may be installed in the IRC5 Compact controller. This is specified in
DeviceNet I/O units on page 98.
How to configure the I/O unit is detailed in Operating manual - RobotStudio.
Location
The location of I/O unit is shown in the following illustration.
xx1400001381
A I/O unit
Required equipment
Equipment Note
I/O unit DSQC 652
See Controller system parts on page 209.

4 Repair
Continued
Removal
The procedure below details how to remove the I/O units or Gateways.
1
DANGER

2
The unit is sensitive to ESD. Before handling the unit

4 Disconnect the connectors from the unit. Note which connector goes
where, to facilitate reassembly.
5 Tip the unit away from the mounting rail and remove
it.
xx1400001382
Refitting
The procedure below describes how to refit the I/O unit.
Action
1
DANGER
2
3 Hook the unit back onto the mounting rail and snap it gently in position.
4 Reconnect all connectors disconnected during removal.

4 Repair
Continued
Action

4 Repair
4.4 Replacement of backup energy bank
Location
The following illustration shows the location of the backup energy bank in IRC5
Compact.
A
xx1400001383
A Backup energy bank
Required equipment
Equipment Note
Backup energy bank DSQC 655
Removal
The following procedure describes how to remove the backup energy bank.
1
DANGER

tion in section DANGER - Make sure that the
main power has been switched off! on
page 33.
2 Remove the cover of the cabinet. See Opening the IRC5 Compact control-
ler on page 89.

4 Repair
Continued
3 Remove the three attachment screws, and
remove the support bar.
xx1400001384
4 Remove the two attachment screws, and pull

the backup energy bank unit slightly out.
xx1400001385
5 Disconnect all connectors from the power

distribution unit.
6 Pull the backup energy bank unit out com-
pletely.

4 Repair
Continued
7 Remove the two attachment screws.
xx1400001386
8 Remove backup energy bank.
Refitting
The procedure below details how to refit the backup energy bank.
1
DANGER

page 33.
2 Refit the new backup energy bank.

3 Refit the attachment screws, and tighten
them.
xx1400001386
4 Slide the backup energy bank unit half way

in.
5 Reconnect all the connectors to the power
distribution unit.

4 Repair
Continued
6 Refit the backup energy bank unit.
xx1400001387
Note
Ensure to fit in the latches properly.
7 Refit the support bar with the three attach-

ment screws.
9 Perform the function tests in section Function
tests on page 118 to verify that the safety

4 Repair
4.5 Replacement of computer unit
Location
The computer unit is located as shown in the illustration below.
A
xx1400001363
A Computer unit
Required equipment
Equipment Note
Computer unit See Spare parts on page 209.
Standard toolkit The contents are defined in section Standard
toolkit.
Other tools and procedures may be required. These procedures include references to the
See references to these procedures in the tools required.
step-by-step instructions below.

4 Repair
Continued
Removal
The procedure below details how to remove the computer unit.
Note
If possible, do a backup of the system before removing the computer unit. For
information on how to do a backup see Operating manual - IRC5 with
FlexPendant.
1
DANGER

page 33.
2
WARNING
The unit is sensitive to ESD. Before handling

the unit please read the safety information
in the section WARNING - The unit is sensit-
ive to ESD! on page 34
3 Open the door in the front and disconnect

all connectors from the computer unit.
page 89.
5 Disconnect all connectors from the computer
unit.
6 Remove the attachment screws for the axis
computer.
A
xx1500000234
A Axis computer attachment screws

4 Repair
Continued
7 Pull the axis computer slightly to release the
latches on the axis computer from the re-
cesses on the assembly plate. Push the axis
computer slightly away from the assembly
plate.
B
A
xx1500000235
A Latches
B Recesses
8 Remove the three attachment screws on the A
assembly plate.
xx1400001388
A attachment screws
9 Slide the assembly plate with computer unit
out of the controller cabinet. Lift the com-
puter unit slightly to get the wrist band button
on the bottom over the edge of the cabinet.
xx1400001447

4 Repair
Continued
10 Loosen the attachment screws, and pull the
computer unit in the direction of the arrow.
The computer unit is suspended by latches
and attachment screws.
xx1400001448
WARNING
Prevent the computer unit from falling

down due to gravity by supporting the
computer unit from beneath by hand.
Refitting
The procedure below describes how to refit the computer unit.
Note
After replacing the main computer, the RobotWare system can be reset. It is then
necessary to restore a backup. For information on how to restore a backup see
Operating manual - IRC5 with FlexPendant.
1
DANGER

page 33.
2
WARNING

in the section WARNING - The unit is sensit-
ive to ESD! on page 34
3 Fit the computer unit in position on the as-

sembly plate.
4 Tighten the attachment screws.

4 Repair
Continued
5 Slide the assembly plate with the computer
unit into the cabinet. The computer unit
should rest on guide structure 1. Guide
structure 2 should fit between the assembly
plate and the computer unit.
A
B
xx1500000236
A Guide structure 1
B Guide structure 2
6 Make sure the computer unit spring is
clipped on to the structure wall inside the
cabinet.
B
A
xx1500000233
A Computer unit spring

B Structure wall
7 Tighten the assembly plate attachment
screws.
8 Fit the axis computer unit so that its latches
fit into the recesses of the assembly plate.
9 Tighten the axis computer unit attachment
screws.
10 Reconnect all connectors to the computer
unit.
12 Perform the function tests in section Function
tests on page 118 to verify that the safety

4 Repair
4.6 Replacement of PCIexpress boards in the computer unit
Location
The following PCIexpress boards may be fitted in the slots in the computer unit as
shown in the figure below:
• DeviceNet Master/Slave
• PROFIBUS-DP Master
• Safety board (second generation SafeMove safety controller)
xx1500001760

Required equipment

Profibus-DP Master 3HAC044872-001 DSQC1005
Profibus communication is de-
scribed in Application manu-
al - PROFIBUS Controller.
DeviceNet Master/Slave 3HAC043383-001 DSQC1006
DeviceNet communication is de-
scribed in Application manual - Devi-
ceNet Master/Slave.
Safety board 3HAC048858-001 DSQC1015
SafeMove (2nd generation) is de-
scribed in Application manual - Func-
tional safety and SafeMove.
Standard toolkit The contents are described in sec-
tion Standard toolkit, IRC5 on
page 207.

4 Repair
Continued

Other tools and procedures may These procedures include refer-
be required. See references to ences to tools required.
these procedures in the step-by-
References

Application manual - PROFIBUS 3HAC050966-001 Contains information on how to
Controller configure the system for PROFIBUS
devices.
Application manual - DeviceNet 3HAC050992-001 Contains information on how to
Master/Slave configure the system for DeviceNet
devices.
Circuit diagram See Circuit dia-
grams on page 217.
Removal
The procedure below details how to remove a PCIexpress board.
1
DANGER

page 33.
2
(ESD)

page 89.
page 138.
5 Disconnect any cables to/from the PCIex-
press board. Tip
Make a note of which cables are disconnec-

ted.

4 Repair
Continued
attachment screws and lift off the upper
cover. Disconnect the fan connector.
CAUTION

A
B
xx1300000684

B Upper cover
the PCIexpress board bracket.
B
A
xx1300000685
A Attachment screw
B PCIexpress board
8 Gently pull the board straight out.
CAUTION

ents.
CAUTION
Immediately put the board in an ESD safe

bag or similar.
Refitting
The procedure below details how to refit a PCIexpress board.
1
DANGER

page 33.

4 Repair
Continued
2
(ESD)

3 Fit the PCIexpress board in position by

pushing the PCIexpress board into the
socket on the motherboard.
B
A
xx1300000685
A Attachment screw
B PCIexpress board
CAUTION

ents.

PCIexpress board bracket.
5 Reconnect any additional cables to the
PCIexpress board.
puter unit.
CAUTION

the upper cover. The fan cable must not be
A
squeezed.
B
xx1300000684

B Upper cover
7 Refit the computer unit. See Replacement of computer unit on
page 138.
8 Refit the controller cover.
9 Make sure the robot system is configured
to support the installed PCIexpress board.
10 Perform the function tests in section
Function tests on page 118 to verify that the
safety features work properly.

4 Repair
4.7 Replacement of Safety module DSQC1015 for SafeMove
Location
The Safety module DSQC1015 is a PCIexpress board that is located inside the
IRC5 main computer unit.
xx1500001760

Required equipment
Equipment Note
DSQC1015 Safety module 3HAC048858-001
toolkit, IRC5 on page 207.
Removing the Safety module
1
DANGER

page 33.

4 Repair
Continued
2
(ESD)

page 89.
page 138.
attachment screws and lift off the cover.
Disconnect the fan connector.
CAUTION

A
B
xx1300000684

B Cover
the slot bracket.
7 Remove the Safety module by pulling it out
of the socket on the motherboard.
A
B
xx1500001761
A Attachment screw
B Safety module
CAUTION

ents.

4 Repair
Continued
Refitting the Safety module
1
DANGER

page 33.
2
(ESD)

3 Fit the Safety module in position by push-

ing it into the socket on the motherboard.
A
B
xx1500001761
A Attachment screw
B Safety module
CAUTION

ents.

Safety module bracket.
puter unit.
CAUTION

the cover. The fan cable must not be
A
squeezed.
B
xx1300000684

B Cover
page 138.

4 Repair
Continued
7 Refit the cover of the cabinet.
basic safety features (e.g. emergency stop)
work properly.
9 Perform a synchronization. See Application manual - Functional safety
and SafeMove.
10 Perform a Cyclic Brake Check. See Application manual - Functional safety
and SafeMove.
11 Lock the SafeMove configuration file. See Application manual - Functional safety
and SafeMove.

4 Repair
4.8 Replacement of expansion board in the computer unit
Location
To connect a serial channel or a fieldbus adapter to the controller, the main
computer must be equipped with the expansion board DSQC1003.
The expansion board is located in the computer unit as shown below.
xx1300000860
A Expansion board with serial channel and one slot for AnybusCC fieldbus adapter.
Required equipment

Expansion Board 3HAC046408-001 DSQC1003
Removal
The following procedure describes how to remove the expansion board from the
computer unit.
1
DANGER

page 33.

4 Repair
Continued
2
(ESD)

page 89.
page 138.
5 Disconnect any cables to/from the fieldbus
adapter.
attachment screws and lift off the upper
cover. Disconnect the fan connector.
CAUTION

A
B
xx1300000684

B Upper cover
7 If there is a fieldbus adapter, remove it. See Replacement of fieldbus adapter in
the computer unit on page 154.
8 Remove the attachment screws on the
computer unit.
xx1300000859
A Attachment screws (2 pcs)

9 Grip the expansion board and gently pull
it straight out. CAUTION
Always grip the expansion board around

the edges to avoid damage to the board
or its components.

4 Repair
Continued
Refitting
The following procedure describes how to refit the expansion board in the computer
unit.
Action Note/Illustrator
1
DANGER

ation in section DANGER - Make sure
that the main power has been switched
off! on page 33.
2
(ESD)
The unit is sensitive to ESD. Before

handling the unit please observe the
safety information in section WARNING
- The unit is sensitive to ESD! on page 34
3 Fit the expansion board in position by

pushing the expansion board into the CAUTION
connector on the motherboard.
Always grip the expansion board around the
CAUTION edges to avoid damage to the board or its
components.
Push carefully so no pins are damaged.
Make sure that the expansion board is
pushed straight into the connector.
4 Secure the expansion board in the com-

puter unit with the attachment screws.
5 Refit the fan connector and close the
computer unit.
CAUTION
Be careful with the fan cable when clos-

ing the upper cover. The fan cable must
not be squeezed.

page 138.
8 Reconnect any cable to the fieldbus ad-
apter.
Function tests on page 118 to verify that
the safety features work properly.

4 Repair
4.9 Replacement of fieldbus adapter in the computer unit
Location
One of the following fieldbus adapters may be fitted in the slot in the computer unit
as shown in the figure below:
• AnybusCC EtherNet/IP slave
• AnybusCC PROFIBUS slave
• AnybusCC PROFINET slave
• AnybusCC DeviceNet slave
xx1300000604
A Slot for AnybusCC fieldbus adapters
Required equipment

AnybusCC EtherNet/IP slave 3HAC027652-001 DSQC 669
fieldbus adapter Ethernet/IP communication is de-
scribed in Application manual - Eth-
erNet/IP Anybus Adapter
AnybusCC PROFIBUS slave 3HAC026840-001 DSQC 667
fieldbus adapter PROFIBUS communication is de-
al - PROFIBUS Anybus Device
AnybusCC PROFINET slave 3HAC031670-001 DSQC 688
fieldbus adapter PROFINET communication is de-
al - PROFINET Anybus Device

4 Repair
Continued

AnybusCC DeviceNet slave 3HAC045973-001 DSQC1004
fieldbus adapter DeviceNet communication is de-
al - DeviceNet Anybus Slave.
Standard toolkit The contents are described in
section Standard toolkit, IRC5 on
page 207.
References

Application manual - EtherNet/IP 3HAC050997-001 Contains information on how to
Anybus Adapter configure the system for Ether-
net/IP Fieldbus Adapter DSQC 669.
Application manual - PROFIBUS 3HAC050965-001 Contains information on how to
Anybus Device configure the system for PROFIB-
US Fieldbus Adapter DSQC 667.
Application manual - PROFINET 3HAC050968-001 Contains information on how to
Anybus Device configure the system for
PROFINET Fieldbus Adapter
DSQC 688.
Application manual - DeviceNet 3HAC050993-001 Contains information on how to
Anybus Slave configure the system for DeviceNet
Fieldbus Adapter DSQC1004.
Circuit diagram See Circuit diagrams
on page 217.
Removal
The following procedure details how to remove the fieldbus adapter from the
computer unit.
1
DANGER

page 33.
2
(ESD)

page 89.
page 138.

4 Repair
Continued
5 Disconnect any cables to/from the fieldbus
adapter.
6 Loosen the attachment screws (2 pcs) on
front of the fieldbus adapter to release the
fastening mechanism.
Note
Only loosen the attachment screws. Do not

remove them.
xx0700000193

B Fastening mechanism
7 Grip the loosened attachment screws and
gently pull the fieldbus adapter straight out.
A
xx1500001755
A Fieldbus adapter

4 Repair
Continued
Refitting
The following procedure details how to refit the fieldbus adapter in the computer
unit.
1
DANGER

ation in section DANGER - Make sure
that the main power has been switched
off! on page 33.
2
(ESD)
The unit is sensitive to ESD. Before

handling the unit please observe the
safety information in section WARNING
- The unit is sensitive to ESD! on page 34
3 Fit the fieldbus adapter in position by

pushing the fieldbus adapter along the
rails on the motherboard.
CAUTION
Push carefully so no pins are damaged.

Make sure that the adapter is pushed
straight onto the rails.
A
xx1500001755
A Fieldbus adapter
CAUTION
Always grip the fieldbus adapter around the

edges to avoid damage to the adapter or its
components.

4 Repair
Continued
4 Secure the fieldbus adapter with its at-
tachment screws (2 pcs).
xx0700000193

B Fastening mechanism
page 138.
7 Reconnect the cable to the fieldbus ad-
apter.
8 Make sure the robot system is configured
to reflect the fieldbus adapter installed.

4 Repair
4.10 Replacement of fan in computer unit
Location
The computer fan is located under the upper cover as shown in the figure below.
xx1300000687
Required equipment
Equipment Note
Fan See Spare parts on page 209.
Cable straps
toolkit.
Other tools and procedures may be required. These procedures include references to the
See references to these procedures in the tools required.

4 Repair
Continued
Removal
The procedure below details how to remove the fan in the computer unit.
1
DANGER

page 33.
2
(ESD)

page 89.
page 138.
C B A
upper cover attachment screws and lift off
the upper cover.
xx1300000688
A Upper cover attachment screws (4

pcs.)
B Fan attachment screw
C Upper cover
6 Disconnect the fan connector and remove
the cable straps. CAUTION

7 Remove the fan attachment screw.

4 Repair
Continued
8 Remove the fan from the upper cover.
xx1300000806
Refitting
The procedure below details how to refit the fan in the computer unit.
1
DANGER

page 33.
2
(ESD)

3 Refit the fan on the upper cover.

4 Refit the attachment screw.
5 Strap the fan cable to the upper cover.
CAUTION
When strapping the cable make sure that

the cable is not stretched or squeezed, and
that the cable does not get caught in the
fan.
6 Refitt the computer unit. See Replacement of computer unit on

page 138.
7 Refitt the controller cover.
puter unit. CAUTION

the upper cover. The fan cable must not be
squeezed.

4 Repair
Continued
safety features work properly.

4 Repair
4.11 Replacement of SD-card memory in computer unit
Location
The location and orientation of the SD-card memory is shown by the following
illustration.
B
A
xx1400001374
A Slot for SD-card memory

B Attachment screw
Note
Only use SD-card memory supplied by ABB.
CAUTION
Reformatting the SD-card or modifying the disk partition can cause irreparable
boot-up problems.
Required equipment
Equipment Note
SD-card 2GB See Spare parts on page 209.
Note
Only use SD-card memory supplied by

ABB.
Includes ABB Boot Application software
to correctly reboot the robot controller.

4 Repair
Continued
Equipment Note
Removal
Use the following procedure to remove the SD-card memory.
Action
1
DANGER
Before commencing any work inside the cabinet, please observe the safety inform-
ation in section DANGER - Make sure that the main power has been switched off!
on page 33.
2
The unit is sensitive to ESD. Before handling the unit please observe the safety
information in section WARNING - The unit is sensitive to ESD! on page 34
3 Remove the attachment screw and open the hatch on the right hand side of the
controller.
4 Gently push the SD-card memory with your finger until it clicks, and then pull it
straight out.
Refitting
Use the following procedure to refit the SD-card memory.
Action
1
DANGER
2
3
CAUTION
Make sure that the SD-card memory is correctly oriented before inserting it. Otherwise
the SD-card memory or the SD-card memory slot may be damaged.
4 Gently push the SD-card memory with your finger until it clicks into place.

4 Repair
4.12 Replacement of drive unit
Location
The following illustration shows the location of the Main Drive Unit.
xx1400001449
A Main Drive Unit
Required equipment
Equipment Note
Main Drive Unit See Controller system parts on page 209.
Standard toolkit The content is described in section Standard
Other tools and procedures may be required.
See references to these procedures in the

4 Repair
Continued
Removal
Use the following procedure to remove the Main Drive Unit.
Action Information
1
DANGER

3 Disconnect the connectors on the top and on the
left on the Main Drive Unit.
xx1400002850
A Connectors on the Main

Drive Unit
4 Remove the six attachment screws in the back of B
the controller.
A
xx1400001619
A Attachment screws for

Main Drive Unit
B Attachment screws for
support bar
5 Remove the support bar by removing the two attach-
ment screws.

4 Repair
Continued
Action Information
6 Push the Main Drive Unit out from the back of the A
controller to get free from the screws in the back B
plane. Then slide the Main Drive Module half way
out.
xx1400002851
A Screws sticking out of the

back plane of the controller
B Connectors on the Main
Drive Unit
7 Disconnect the connectors from the right side of
the Main Drive Unit.
8 Remove the Main Drive Unit from the controller.
9 Loosen the two lower attachment screws, and re- A
move the two upper screws, to remove the drive
unit from mounting frame.
B
xx1400001450
A Upper attachment (2 pcs.)

B Lower attachment (2 pcs.)

4 Repair
Continued
Refitting
Use the following procedure to refit the Main Drive Unit.
Action
1
DANGER
in section DANGER - Make sure that the main power has been switched off! on
page 33.
2 Fit the unit in its intended position and orientation on the mounting frame. Secure it
with its attachment screws.
3 Slide the Main Drive Unit half way into the controller.
4 Reconnect the connectors on the right side of the Main Drive Unit.
5 Refit the Main Drive Unit in the controller and secure it with its attachment screws.
6 Refit support bar with its attachment screws.
7 Reconnect the connectors on the top and left on the Main Drive Unit.

4 Repair
4.13 Replacement of axis computer
Location
The location of the axis computer is shown by the following illustration.
xx1400001451
A Axis computer unit
Required equipment
Axis computer DSQC 668
Other tools and procedures may be required. See
references to these procedures in the step-by-

4 Repair
Continued
Removal
Use the following procedure to remove the axis computer.
1
DANGER

page 33.
2
(ESD)

the unit please observe the safety informa-
tion in section WARNING - The unit is
sensitive to ESD! on page 34
3 Remove the cover of the cabinet. See Opening the IRC5 Compact controller
on page 89.
4 Disconnect all connectors from the axis
computer unit. Note
Make a note of any connections.
5 Remove the attachment screws.
A
xx1500000234
A Attachment screws
6 Slide the axis computer unit out of the con-
troller.

4 Repair
Continued
7 Remove the seven attachment screws and
gently lift the axis computer board straight
up.
xx1000000953
A Axis computer board

B Axis computer cover
C Attachment screws
Refitting
Use this procedure to refit the axis computer.
1
DANGER

page 33.
2
(ESD)

in the section WARNING - The unit is sens-
itive to ESD! on page 34
3 Gently fit the axis computer board into the

cover and refit the attachment screws.

4 Repair
Continued
4 Slide the axis computer unit into the control-
ler, ensuring that the latches fit into the re-
cesses.
B
A
xx1500000235
A Latches
B Recesses
5 Tighten the axis computer unit attachment
screws.
6 Reconnect all the connectors.
8 Perform the function tests in section Func-
tion tests on page 118 to verify that the safety

4 Repair
4.14 Replacement of contactor unit
Location
The following illustration shows the location of the contactor unit in IRC5 Compact.
xx1400002008
A Contactor unit
Required equipment
Equipment Note
Contactor unit Contactor ASL16-30-10 DC24V
See Miscellaneous parts on page 212.
Removal
The following procedure describes how to remove the backup energy bank.
1
DANGER

page 33.

4 Repair
Continued
2 Remove the cover of the cabinet. See Opening the IRC5 Compact control-
ler on page 89.
3 Disconnect all wires from the contactor unit. Make a note of all connections.
4 Remove the two attachment screws. A
xx1400002030
5 Remove contactor unit, and replace each

defective component.
Refitting
The procedure below details how to refit the backup energy bank.
Action
1
DANGER
2 Refit the contactor unit.

3 Refit the attachment screws, and tighten them.
4 Reconnect all wires.

4 Repair
4.15 Replacement of brake resistor bleeder
Location
The following illustration shows the location of the brake resistor bleeder.
B C
xx1400001457
A Bleeder
B Fan cover
C Attachment screws
Required equipment
Equipment Note
Brake resistor bleeder See Miscellaneous parts on page 212.
Standard toolkit The content is described in section Standard toolkit,
IRC5 on page 207.
Removal
Use the following procedure to remove the line filter.
1
DANGER
Before commencing any work

inside the cabinet, please ob-
serve the safety information in
section DANGER - Make sure
that the main power has been

4 Repair
Continued
2
CAUTION
Hot surface on top of the bleeder.

Risk of burns. Be careful when
removing the unit.
3 Remove the fan cover.

4 Disconnect the bleeder connect-
or. A
xx1500000119
A Bleeder connector
A
5 Loosen the two lower attachment
screws on the bleeder bracket.
xx1400001458
A Upper attachment screw

B Lower attachment screws
6 Remove the upper attachment
screw.
7 Pull the brake resistor bleeder
upwards and then outwards, to
release it from the lower screw
heads, and remove it.

4 Repair
Continued
Refitting
Use the following procedure to refit the line filter.
1
DANGER
Before commencing any work

inside the cabinet, please ob-
serve the safety information in
section DANGER - Make sure
that the main power has been
A
2 Refit the brake resistor bleeder
by sliding the recesses in be-
neath the lower attachment
screw heads, and push it inwards
and then downwards.
xx1400001458
A Upper attachment screw

B Lower attachment screws
3 Refit the upper attachment
screw.
4 Tighten all the attachment screws
for the bleeder.
5 Reconnect the bleeder connect-
or.
6 Refit the fan cover, push it left
towards the grooves.
7 Refit the attachment screws for
the fan cover, and tighten them.
8 Perform the function tests in
section Function tests on
page 118 to verify that the safety

4 Repair
4.16 Replacement of system fans
Location
The following illustration shows the location of the system fans.
B C
xx1400001454
A System fan
B Fan cover
C Attachment screws
Required equipment
Equipment Note
Fan with receptacle See Miscellaneous parts on page 212.

4 Repair
Continued
Removal
Use this procedure to remove one of the system fans.
1
DANGER

page 33.
2
CAUTION
Hot surface on top of the bleeder. Risk of

burns. Be careful when removing the unit.
3 Remove four attachment screws on the fan

cover.
4 Push the fan cover to the left and remove it.
5 Remove brake resistor bleeder. See Replacement of brake resistor
bleeder on page 175.
6 Disconnect the connectors to the fan.
7 Loosen the attachment screw on the fan re-
ceptacle.
xx1400001456
8 Push the fan according to illustration, to re-

lease and remove it.
Refitting
Use this procedure to refit one of the system fans.
1
DANGER

page 33.
2 Put the fan in place and push it upwards.

3 Fasten the attachment screw on the fan re-
ceptacle.
4 Connect the connectors to the fan.

4 Repair
Continued
5 Refit and connect the brake resistor bleeder. See Replacement of brake resistor
bleeder on page 175.
6 Put the fan cover in place and push it to the
right.
7 Fasten the four attachment screws on the
fan cover.
8 Perform the function tests in section Func-
tion tests on page 118 to verify that the safety

4 Repair
4.17 Replacement of Remote Service box
Location
The following illustration shows the location of the Remote Service box.
xx1500000230
A Attachment screws
B Safety board
C Ethernet switch
D Remote Service box
Required equipment
Remote Service box DSQC 680

4 Repair
Continued
Removal
Use this procedure to remove the Remote Service box.
Action Information
1
DANGER

2

3 On the cabinet front, disconnect the connectors

from the Remote Service contacts.
If you have an Ethernet switch, disconnect the
connectors from this as well.
A B
xx1400002787
A Remote Service contacts

B Ethernet switch contacts
5 Disconnect all connectors from the safety board,
Remote Service box, and Ethernet switch.
6 Remove the two attachment screws, and push the
safety board unit backwards to release the latches.
xx1400001462

4 Repair
Continued
Action Information
7 Pull the latch (A) to the left, and push the Remote
Service box out.
xx1400001460
Refitting
Use this procedure to refit the Remote Service box.
Action
1
DANGER
2
The unit is sensitive to ESD. Before handling the unit please read the safety information
in the section WARNING - The unit is sensitive to ESD! on page 34
3 Pull the latch to the left and push the Remote Service box in position on the mounting
bracket.
4 Refit the safety board unit and secure it with attachment screws.
5 Reconnect all connectors to the Remote Service box, Ethernet switch and safety board.

4 Repair
4.18 Replacement of Ethernet switch
Location
The following illustration shows the location of the Ethernet switch.
xx1500000230
A Attachment screws
B Safety board
C Ethernet switch
D Remote Service box
Required equipment
Ethernet switch 3HAC034884-001

4 Repair
Continued
Removal
Use this procedure to remove the Ethernet switch.
Action Information
1
DANGER

2

3 On the cabinet front, disconnect the connectors

from the Ethernet switch contacts.
If you have a Remote Service box, disconnect the
connectors from this as well.
A B
xx1400002787
A Remote Service contacts

B Ethernet switch contacts
5 Disconnect all connectors from the safety board,
Ethernet switch, and Remote Service box.
6 Remove the two attachment screws, and push the
safety board unit backwards to release the latches.
xx1400001462
7 Remove the attachment screws, and lift off the

safety board.
xx1500000231
8 Remove the Ethernet switch.

4 Repair
Continued
Refitting
Use this procedure to refit the Ethernet switch.
Action
1
DANGER
2
The unit is sensitive to ESD. Before handling the unit please read the safety information
in the section WARNING - The unit is sensitive to ESD! on page 34
3 Refit the Ethernet switch.

4 Refit the safety board and secure it with the attachment screws.
5 Refit the safety board unit and secure it with the attachment screws.
6 Reconnect all connectors to the Ethernet switch, Remote Service box, and safety
board.

4 Repair
4.19.1 Replacement of power distribution unit
4.19 Replacement of power supply
Location
The location of the power distribution unit is shown by the following illustration.
xx1400001463
A Power distribution unit
CAUTION
Hot surface on top of the power distribution unit.

Risk of burns. Be careful when removing the unit.
Do not route or place cables on top of the power distribution unit.
Required equipment
Equipment Note
Power distribution unit DSQC 662
Standard toolkit The content is described in section Standard toolkit,
IRC5 on page 207.

4 Repair
Continued
Equipment Note
Other tools and procedures may be
required. See references to these pro-
cedures in the step-by-step instructions
below.
Removal
Use this procedure to remove the power distribution unit.
1
DANGER

cabinet, please observe the safety in-
formation in section DANGER - Make
sure that the main power has been
2
CAUTION
Hot surface on top of the power distribu-

tion unit.
Risk of burns. Be careful when removing
the unit.
3 Remove the cover of the cabinet. See Opening the IRC5 Compact controller on
page 89.
4 Remove the three attachment screws,
and remove the support bar.
xx1400001384

4 Repair
Continued
5 Remove the two attachment screws, and
pull the backup energy bank unit slightly
out.
xx1400001385
6 Disconnect all connectors from the

power distribution unit.
7 Pull the backup energy bank unit out
completely.
8 Remove the attachment screws and lift B
the board out.
A
xx0900000549
• A: power distribution unit

• B: attachment screws

4 Repair
Continued
9 Remove the two attachment screws and
cover plate.
xx1400001464
10 Remove the five attachment screws and

spring.
xx1400001465
Refitting
Use this procedure to refit the power distribution unit.
1
DANGER


4 Repair
Continued
2 Put the new power distribution unit in B
place and refit the attachment screws.
A
xx0900000549
• A: power distribution unit

• B: attachment screws
3 Refit the spring and cover plate. Secure
with attachment screws.
4 Refit the power distribution unit and se-
cure with attachment screws.
5 Slide the backup energy bank unit half
way in.
6 Reconnect the connectors X1 - X9.
CAUTION
Hot surface on top of the power distribu-

tion unit.
Do not route or place cables on top of
the power distribution unit.
7 Refit the backup energy bank unit.

8 Refit the support bar with the three at-
tachment screws.

4 Repair
4.19.2 Replacement of system power supply
Location
The following illustration shows the location of the system power supply.
xx1400001466
A System power supply
Required equipment
Equipment Note
System power supply DSQC 661
Removal
Use the following procedure to remove the system power supply.
1
DANGER


4 Repair
Continued
3 Disconnect all connectors from the unit.
4 Remove the right side beam, according to illustra- A B C
tion.
xx1400001468
• A: torx counters head

screw (2 pcs)
• B: torx pan head screw (2
pcs)
• C: beam
• D: torx pan head screw
(support)
• E: support
5 Remove two attachment screws in the back of the
controller, to loosen support bracket.
xx1400001467
6 Pull the system power supply with support bracket

straight up.

4 Repair
Continued
7 Loosen the two lower attachment screws.
A
B
xx0900000570
• A: upper attachment
screws
• B: lower attachment screws
8 Remove the two upper attachment screws.
9 Pull the power supply unit upwards to release it
from the lower screw heads, and remove it.
Refitting
Use the following procedure to refit the system power supply.
1
DANGER


4 Repair
Continued
2 Refit the power supply by sliding the recesses in
beneath the lower screw heads.
A
B
xx0900000570
• A: upper attachment
screws
• B: lower attachment screws
3 Refit the two upper attachment screws.
4 Tighten the attachment screws (4 pcs).
5 Refit system power supply with support bracket by A
fitting the latches into the recesses.
B C
xx1400001469
• A: support bracket
• B: recess
• C: latch
6 Refit the two attachment screws to the support
bracket in the back of the controller
7 Refit right side beam and secure with attachment
screws.
8 Reconnect all connectors to the unit.

4 Repair
Continued
10 Perform the function tests in section Function tests
on page 118 to verify that the safety features work
properly.

4 Repair
4.19.3 Replacement of line filter
Location
The following illustration shows the location of the line filter.
xx1400001470
A Filter
Required equipment
Equipment Spare part no. Note

Line filter 3HAC037698-001 See Controller system parts on page 209.
Standard toolkit The content is de-
scribed in section
Standard toolkit, IRC5
on page 207.
Other tools and proced-
ures may be required.
See references to these
procedures in the step-
by-step instructions be-
low.

4 Repair
Continued
Removal
Use the following procedure to remove the line filter.
1
DANGER

2 Remove the cover of the cabinet. See Opening the IRC5 Compact controller on
page 89.
3 Disconnect connector X1 from the sys-
tem power supply.
xx1400002853
A Connector X1
B Ground connection
4 Disconnect the ground connection.
5 Disconnect and remove the safety board See Replacement of Remote Service box on
unit to be able to access the secondary page 181.
side of the line filter.
6 Disconnect the cables from L1', L2' on
the secondary side of the line filter.
xx1400002854
A Line filter connections

4 Repair
Continued
7 Remove the two support bracket attach-
ment screws and pull the line filter out
slightly. B
xx1400002849
A Attachment screws for the support

bracket
B L1 and L2 connections
C Ground connection
8 Disconnect the cables from L1, L2 and
ground connection on the primary side
of the line filter.
9 Pull the line filter unit out.
10 Disconnect the ground cable cable from
the secondary side of the line filter.
11 Remove the four attachment screws of
the line filter and remove it from the
support bracket.
xx0900000572
A Attachment screws for the line filter
Refitting
Use the following procedure to refit the line filter.
1
DANGER


4 Repair
Continued
2 Fit the line filter in position on the sup-
port bracket and secure the four attach-
ment screws.
3 Reconnect the ground cable to the sec-
ondary side of the line filter.
4 Slide the line filter into the controller.
5 Reconnect the cables to L1, L2 and
ground connection on the primary side
of the line filter.
6 Refit the line filter unit by fitting the A
latches into the recesses.
B C
xx140000XXXX
A Line filter
B Latches
C Recess
7 Secure the line filter unit with two attach-
ment screws.
8 Reconnect the cables to L1' and L2'
connections on the secondary side of
the line filter.
9 Refit the safety board unit with its two
attachment screws.
10 Reconnect all connectors to the safety
board unit.
11 Reconnect connector X1 to the system
power supply.
12 Reconnect the ground connection under
the system power supply.

5 Decommissioning
5.1 Introduction
5 Decommissioning
5.1 Introduction
Introduction
This section contains information to consider when taking a product, robot or
controller, out of operation.
It deals with how to handle potentially dangerous components and potentially
hazardous materials.
General
All used grease/oils and dead batteries must be disposed of in accordance with
the current legislation of the country in which the robot and the control unit are
installed.
If the robot or the control unit is partially or completely disposed of, the various
parts must be grouped together according to their nature (which is all iron together
and all plastic together), and disposed of accordingly. These parts must also be
disposed of in accordance with the current legislation of the country in which the
robot and control unit are installed.

5 Decommissioning
5.2 Environmental information
5.2 Environmental information
Hazardous material
The table specifies some of the materials in the product and their respective use
throughout the product.
Dispose components properly according to local regulations to prevent health or
environmental hazards.
Material Example application
Batteries, NiCad or Lithium Main computer
Copper Cables
Steel Cabinet structure, plates, screws, etc.
Plastic/rubber Cables, connectors, etc.
Aluminium Heat sinks on power supplies and drive units
Lead Electronics
Brominated flame retardants Electronics

6 Reference information
6.1 Introduction
6.1 Introduction
General
This chapter includes general information, complementing the more specific
information in the different procedures in the manual.

6.2 Applicable standards
Note
The listed standards are valid at the time of the release of this document. Phased
out or replaced standards are removed from the list when needed.
Standards, EN ISO
The product is designed in accordance with the requirements of:
Standard Description
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk as-
sessment and risk reduction
EN ISO 13849-1:2015 Safety of machinery, safety related parts of control systems -
Part 1: General principles for design
EN ISO 13850:2015 Safety of machinery - Emergency stop - Principles for design
EN ISO 10218-1:2011 Robots for industrial environments - Safety requirements -Part
1 Robot
ISO 9787:2013 Robots and robotic devices -- Coordinate systems and motion
nomenclatures
ISO 9283:1998 Manipulating industrial robots, performance criteria, and related
test methods
EN ISO 14644-1:2015 i Classification of air cleanliness
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Part 1
EN 61000-6-4:2007 + EMC, Generic emission
A1:2011
IEC 61000-6-4:2006 +
A1:2010
(option 129-1)
EN 61000-6-2:2005 EMC, Generic immunity
IEC 61000-6-2:2005
EN IEC 60974-1:2012 ii Arc welding equipment - Part 1: Welding power sources
EN IEC 60974-10:2014 ii Arc welding equipment - Part 10: EMC requirements
EN IEC 60204-1:2006 Safety of machinery - Electrical equipment of machines - Part
1 General requirements
IEC 60529:1989 + A2:2013 Degrees of protection provided by enclosures (IP code)
i Only robots with protection Clean Room.
ii Only valid for arc welding robots. Replaces EN IEC 61000-6-4 for arc welding robots.
European standards
EN 614-1:2006 + A1:2009 Safety of machinery - Ergonomic design principles - Part 1:
Terminology and general principles
EN 574:1996 + A1:2008 Safety of machinery - Two-hand control devices - Functional
aspects - Principles for design

Continued
Other standards
ANSI/RIA R15.06 Safety requirements for industrial robots and robot systems
ANSI/UL 1740 Safety standard for robots and robotic equipment
CAN/CSA Z 434-14 Industrial robots and robot Systems - General safety require-
ments

6.3 Unit conversion
6.3 Unit conversion
Converter table
Use the following table to convert units used in this manual.
Quantity Units
Length 1m 3.28 ft. 39.37 in
Weight 1 kg 2.21 lb.
Weight 1g 0.035 ounces
Pressure 1 bar 100 kPa 14.5 psi
Force 1N 0.225 lbf
Moment 1 Nm 0.738 lbf-ft
Volume 1L 0.264 US gal

6.4 Standard toolkit, IRC5
6.4 Standard toolkit, IRC5
General
All service (repair, maintenance and installation) instructions contain lists of tools
required to perform the specified activity. All special tools, that is, all tools that are
not considered as standard tools as defined below, are listed in their instructions
respectively.
This way, the tools required are the sum of the Standard Toolkit and any tools
listed in the instructions.
Contents, standard toolkit, IRC5
Tool Remark
Screw driver, Torx Tx10
Ball tipped screw driver, Torx Tx25
Screw driver, flat blade 4 mm
Screw driver Phillips-1
Box spanner 8 mm

6.5 Screw joints
6.5 Screw joints
General
This section details how to tighten the various types of screw joints on the controller.
The instructions and torque values are valid for screw joints comprised of metallic
materials and do not apply to soft or brittle materials.
Tightening torque
Before tightening any screw, note the following:
• Determine whether a standard tightening torque or special torque is to be
applied. The standard torques are specified in the tables below. Any special
torques are specified in the Repair, Maintenance or Installation procedure
description. Any special torque specified overrides the standard value.
• Use the correct tightening torque for each type of screw joint.
• Only use correctly calibrated torque keys.
• Always tighten the joint by hand, and never use pneumatical tools.
• Use the correct tightening technique, i.e. do not jerk. Tighten the screw in a
slow, flowing motion.
• Maximum allowed total deviation from the specified value is 10%!
The table below specifies the recommended standard tightening torque for
oil-lubricated screws with slotted or cross-recess heads.
Dimension Tightening torque (Nm)
Class 4.8, oil-lubricated
M2.5 0.25
M3 0.5
M4 1.2
M5 2.5
M6 5.0

7 Spare parts
7.1 IRC5 Compact controller
7 Spare parts
Controller system parts

A B
D E
F G H J
xx1400001621
Spare part no. Description Note

A 3HAC036260-001 Main Drive Unit, MDU-430C DSQC 431
B 3HAC037310-001 Safety board DSQC 400
3HAC059163-001 DSQC 400E
C 3HAC037698-001 Line filter

7 Spare parts
Continued

D 3HAC043053-001 Remote Service box DSQC 680
E 3HAC026253-001 System Power Supply DSQC 661
F See Computer unit parts on page 210.
G 3HAC028179-001 Axis computer DSQC 668
H 3HAC025562-001 Backup energy bank DSQC 655
J 3HAC026254-001 Power distribution unit DSQC 662
3HAC051190-001 Multipole con. XS7, XS8, XS9
Computer unit parts

The illustration below shows the placement of the computer unit parts in the
recommended spare part list.
A B
xx1300000851
Spare part no. Description Type

A 3HAC042766-001 Computer unit (1 PCI slot) DSQC1000
A 3HAC050363-001 Computer unit (2 PCI slots) DSQC1018
B 3HAC047184-003 Mass Memory with boot loader 2GB -
(previously called
DSQC1008)
C 3HAC046408-001 Expansion Board complete DSQC1003
D 3HAC031670-001 PROFINET Slave Fieldbus Adapter DSQC 688
D 3HAC026840-001 PROFIBUS Slave Fieldbus Adapter DSQC 667
D 3HAC027652-001 Ethernet/IP Slave Fieldbus Adapter DSQC 669
D 3HAC045973-001 DeviceNet Slave Fieldbus Adapter DSQC1004

7 Spare parts
Continued
Spare part no. Description Type

E 3HAC043383-001 DeviceNet Master/Slave PCIexpress DSQC1006
E 3HAC044872-001 PROFIBUS-DP Master PCIexpress DSQC1005
F 3HAC026525-001 Fan -
- 3HAC14944-1 RS-232/422 Converter DSQC 615
I/O System parts
xx1400001381
A I/O unit

* 3HAC025784-001 ADCombi I/O unit DSQC 651
A 3HAC025917-001 Digital 24V I/O unit DSQC 652
* 3HAC025918-001 Digital I/O with relay outputs DSQC 653
* Mounted outside controller cabinet

7 Spare parts
Continued
Miscellaneous parts
xx1400002002
Spare part no. Description

A 3HAC051187-001 Brake resistor bleeder asm
B 3HAC037699-001 Handle for 6 mm switch
C 3HAC052287-003 Mode selector
D 3HAC051135-001 Fan with receptacle
3HAB2997-1 Wrist band
3HAC037700-001 Contactor ASL16-30-10 DC24V
3HAC031562-001 Auxiliary contact CA3-01
3HAC033498-001 FlexPendant holder
3HAC033596-002 FlexPendant holder upper part
3HAC052262-001 Mounting kit, 19" cabinet
External operator's panel

- 3HAC038671-001 External control panel box Option 733-4
- 3HAC038672-001 External Operator's panel cable 7m Option 734-5

7 Spare parts
7.2 Manipulator cables
Signal cables, IRB 120

3HAC035320-001 Control cable signal 3 m
Power cables, IRB 120

3HAC032694-001 Control cable power 3 m
CP/CS cables IRB 120, IRB 1200, IRB 910SC
Art. no. Description Option no.

3HAC049186-001 Customer cable signal 3 m 94-6
Cable packages for IRB 140 (including signal, power and customer cables)
Art. no. Description



7 Spare parts
Continued

Cable packages for IRB 360 (including signal, power and customer cables)

3HAC029903-001 Control cable, power and signal 3 m
3HAC038411-001 Control cable, power and signal, stainless contact screws, 3 m
Signal cables, IRB 910SC

Power cables, IRB 910SC



7 Spare parts
Continued

Ethernet cables, IRB 1200

3HAC055518-001 Ethernet cable 3 m 859-9
Signal cables, IRB 1410, 1600

Power cables, IRB 1410, 1600

CP/CS cables IRB 1600

3HAC061420-001 Cable CP/CS 7 m 94-1, 16-1 and 17-5

7 Spare parts
Continued


8 Circuit diagrams
8.1 Circuit diagrams
8 Circuit diagrams
Overview
The circuit diagrams are not included in this manual, but delivered as separate
documents on the documentation DVD. See the article numbers in the tables below.
Controllers
Product Article numbers for circuit diagrams

Circuit diagram - IRC5 3HAC024480-011
Circuit diagram - IRC5 Compact 3HAC049406-003
Circuit diagram - IRC5 Panel Mounted Con- 3HAC026871-020
troller
Circuit diagram - Euromap 3HAC024120-004
Circuit diagram - Spot welding cabinet 3HAC057185-001
Robots

Circuit diagram - IRB 120 3HAC031408-003
Circuit diagram - IRB 140 type C 3HAC6816-3
Circuit diagram - IRB 1600/1660 3HAC021351-003
Circuit diagram - IRB 4400/4450S 3HAC9821-1
Circuit diagram - IRB 6400RF 3HAC8935-1
Circuit diagram - IRB 6600 type A 3HAC13347-1
3HAC025744-001
Circuit diagram - IRB 6600 type B 3HAC13347-1
3HAC025744-001

8 Circuit diagrams
Continued

Circuit diagram - IRB 6620 / IRB 6620LX 3HAC025090-001
Circuit diagram - IRB 6650S 3HAC13347-1
3HAC025744-001
3HAC029940-001
3HAC025744-001
Circuit diagram - IRB 910SC 3HAC056159-002

Index
Index H
hazardous material, 202
A I
aluminum I/O contact XS7, 77
disposal, 202 installation space, 47
auto stop, 123 IP class, 45
ISO 13849-1, 24
B
batteries K
disposal, 202 key of the mode switch, 40
brake contactor, 122
brominated flame retardants L
disposal, 202 labels
controller, 29
C lead
cabinet lock, 21 disposal, 202
cables, 213 Lithium
carbon dioxide extinguisher, 23 disposal, 202
category 0 stop, 19
category 1 stop, 19 M
category 3, 24 main power
CCF, 24 switching off, 33
cleaning the FlexPendant, 115 main power switch, 33
Common Cause Failures, 24 maintenance schedule, 111
connecting a USB memory, 92 manipulator cables, 213
connection memory, 163
external safety devices, 17 memory functions, 91
FlexPendant, 57 mode switch, 119
controller mode switch key, 40
symbols, 29 motor contactors, 121
copper MTTFD, 24–25
disposal, 202
N
D network security, 14
danger levels, 27 NiCad
DC, 24 disposal, 202
DeviceNet contact XS11, 78–79
Diagnostic Coverage, 24 O
DSQC1015, 147 operating conditions, 45
E P
emergency stop, 19, 118 PCIexpress boards, replace, 143
buttons, 20 performance level, PL, 24
emergency stops PFHD, 26
recovering, 41 PL, performance level, 24
enabling device, 102, 120 plastic
EN ISO 13849-1, 24, 26 disposal, 202
environmental information, 202 power cables, 213
ESD power supply contact XS10, 77
damage elimination, 34 product standards, 204
sensitive equipment, 34 protection class, 45
wrist strap connection point, 35 protective stop, 19
Ethernet switch, 184 definition, 19
expansion board, replace, 151
external enabling device, 102 R
external operator’s panel, 99 reduced speed control, 125
Remote Service, 181
F removing
fieldbus adapter, replace, 154 top cover, 89
fire extinguishing, 23 replacements, report, 127
FlexPendant replacing
connecting, 57 Ethernet switch, 184
function tests, 118 expansion board, 151
fieldbus adapter, 154
G PCIexpress boards, 143
general stop, 124 Remote Service box, 181

Index
SD-card memory, 163 safety, 27

report replacements, 127 standards, 204
required performance level, PLr, 24 ANSI, 205
responsibility and validity, 17 CAN, 205
robot cables, 213 EN, 204
rubber EN IEC, 204
disposal, 202 EN ISO, 204
steel
S disposal, 202
safeguarding, 19 stop category 0, 19
SafeMove, 104, 143, 147 stop category 1, 19
safety stops
emergency stop, 20 overview, 19
ESD, 34 storage conditions, 45
fire extinguishing, 23 symbols
introduction, 15 safety, 27
robot, 17
service, 17 T
signals, 27 temperature, 45
signals in manual, 27 three-position enabling device, 120
stop functions, 19 tightening torque, 208
symbols, 27 top cover, 89
symbols on controller, 29
wrist strap, 35 U
safety board, 104, 143 USB ports, 92
safety contact XS9, 76
Safety module, 147 V
safety risk validity and responsibility, 17
electric parts, 21
voltage, 21 W
safety signals weight, 45
in manual, 27 X
safety standards, 204 XS7 I/O, 77
SD-card memory, replace, 163 XS9 Safety, 76
signal cables, 213 XS10 Power Supply, 77
signals XS11 DeviceNet, 78–79

3HAC047138-001, Rev G, en
ABB AB, Robotics
Robotics and Motion
S-721 68 VÄSTERÅS, Sweden
Telephone +46 (0) 21 344 400
ABB AS, Robotics

Robotics and Motion
Nordlysvegen 7, N-4340 BRYNE, Norway
Box 265, N-4349 BRYNE, Norway
Telephone: +47 22 87 2000
ABB Engineering (Shanghai) Ltd.

Robotics and Motion
No. 4528 Kangxin Highway
PuDong District
SHANGHAI 201319, China
Telephone: +86 21 6105 6666
ABB Inc.
Robotics and Motion
1250 Brown Road
Auburn Hills, MI 48326
USA
Telephone: +1 248 391 9000
www.abb.com/robotics

ABB IRC5 Compact Product Manual HAC047138-001 RevG en

Uploaded by

Copyright:

Available Formats

ABB IRC5 Compact Product Manual HAC047138-001 RevG en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ABB IRC5 Compact Product Manual HAC047138-001 RevG en

Uploaded by

Copyright:

Available Formats

ROBOTICS

Document ID: 3HAC047138-001

© Copyright 2009-2017 ABB. All rights reserved.

© Copyright 2009-2017 ABB. All rights reserved.

2 Installation and commissioning 43

Product manual - IRC5 Compact 5

2.8 Drive system .................................................................................................... 90

6 Product manual - IRC5 Compact

6 Reference information 203

7 Spare parts 209

8 Circuit diagrams 217

Product manual - IRC5 Compact 7

Overview of this manual

Who should read this manual?

Continues on next page

Continues on next page

Product manual - IRC5 Compact 11

Product documentation, IRC5

Technical reference manuals

Continues on next page

Product manual - IRC5 Compact 13

14 Product manual - IRC5 Compact

Product manual - IRC5 Compact 15

1.2 General safety information

1.2.1 Introduction to general safety information

16 Product manual - IRC5 Compact

1.2.2 Safety in the robot system

Validity and responsibility

Connection of external safety devices

Type of information Detailed in document Section

Continues on next page

Type of information Detailed in document Section

18 Product manual - IRC5 Compact

1.2.3 Protective stop and emergency stop

Inputs to initiate a protective stop or an emergency stop

To modify the configuration of the stop category, see Technical reference

Continues on next page

Other methods to stop the robot

20 Product manual - IRC5 Compact

1.2.4 Safety risks

1.2.4.1 Risks associated with live electric parts

Voltage related risks, general

Voltage related risks, IRC5 controller

Continues on next page

Voltage related risks, robot

Voltage related risks, tools, material handling devices, etc.

22 Product manual - IRC5 Compact

1.2.5 Safety actions

1.2.5.1 Fire extinguishing

Product manual - IRC5 Compact 23

1.2.6 Safety data

About this section

Prevailing directives and standards

Performance level and category

Performance level for ABB IRC5 controller

Continues on next page

Safety function Calculated MTTFD DCavg

Continues on next page

Stop circuit Calculated PFHD PL