M54/74HC160/161

M54/74HC162/163

SYNCHRONOUS PRESETTABLE 4-BIT COUNTER

. HIGH SPEED

. fMAX = 63 MHz (TYP.) AT VCC = 5 V

LOW POWER DISSIPATION

. ICC = 4 µA (MAX.) AT 25 °C
OUTPUT DRIVE CAPABILITY

. 10 LSTTL LOADS
BALANCED PROPAGATION DELAYS B1R F1R

. tPLH = tPHL
HIGH NOISE IMMUNITY
(Plastic Package) (Ceramic Package)

. VNIH = VNIL = 28 % VCC (MIN.)

WIDE OPERATING VOLTAGE RANGE

. VCC (OPR) = 2 V TO 6 V
PIN AND FUNCTION COMPATIBLE
WITH 54/74LS160 ∼ 163
M1R
(Micro Package)
C1R
(Chip Carrier)
ORDER CODES :
M54HCXXXF1R M74HCXXXM1R
M74HCXXXB1R M74HCXXXC1R
DESCRIPTION
M54/74HC160 Decade, Asynchronous Clear
M54/74HC161 Binary, Asynchronous Clear
M54/74HC162 Decade, Synchronous Clear PIN CONNECTIONS (top view)
M54/74HC163 Binary, Synchronous Clear
The M54/74HC160, 161, 162 and 163 are high
speed CMOS SYNCHRONOUS PRESETTABLE
COUNTERS fabricated with silicon gate C2MOS
technology.
They have the same the high speed operation simi-
lar to equivalent LSTTL while maintaining the
CMOS low power dissipation.
The M54/74HC160/162 are BCD Decade counters
and the M54/74HC161/163 are 4 bit binary counter-
s.
The CLOCK input is active on the rising edge. Both
LOAD and CLEAR inputs are active Low.
Presetting of all four IC’s is synchronous on the ris-
ing edge of the CLOCK.
The function on the M54/74HC162/163 is syn-
chronous to CLOCK, while the M54/74HC160/161
counters are cleared asynchronously.
Two enable inputs (TE and PE) and CARRY output
are provided to enable easy cascading of counters,
which facilities easy implementation of N-bit
counters without using external gates.
NC =
All inputs are equipped with protection circuits No Inter-
against static discharge and transient excess volt- nal Con-
age.

April 1993 1/16

M54/M74HC160/161/162/163

INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION

PIN No SYMBOL NAME AND FUNCTION
1 CLEAR Asynchronous Master
reset
2 CLOCK Clock Input (LOW to
HIGH, Edge-triggered)
3, 4, 5, 6 A, B, C, D Data Inputs
7 ENABLE P Count Enable Input
10 ENABLET Count Enable Carry Input
9 LOAD Parallel Enable Input
14, 13, 12, QA to QD Flip Flop Outputs
11
15 CARRY Terminal Count Output
OUTPUT
8 GND Ground (0V)
16 VCC Positive Supply Voltage

IEC LOGIC SYMBOL (HC160) IEC LOGIC SYMBOL (HC161)

IEC LOGIC SYMBOL (HC162) IEC LOGIC SYMBOL (HC163)

2/16
 M54/M74HC160/161/162/163

TRUTH TABLE
M54/74HC160/161 M54/74HC162/163
OUTPUTS
INPUTS INPUTS FUNCTION
CLR LD PE TE CK CLR LD PE TE CK QA QB QC QD
L X X X X L X X X L L L L RESET TO ”0”
H L X X H L X X A B C D PRESET DATA
H H X L H H X L NO CHANGE NO COUNT
H H L X H H L X NO CHANGE NO COUNT
H H H H H H H H COUNT UP COUNT
H X X X X X X X NO CHANGE NO COUNT
Note: X : Don’t Care
A, B, C, D : Logi level of data inputs
Carry : CARRY = TE • QA • QB • QC • QD ............ (M54/74HC160/162)
: CARRY = TE • QA • QB • QC • QD ............ (M54/74HC161/163)

TIMING CHART (HC160/162 : decade counter)

3/16
M54/M74HC160/161/162/163

TIMING CHART (HC161/163 : binary counter)

4/16
 M54/M74HC160/161/162/163

LOGIC DIAGRAM

HC160

LOGIC DIAGRAM

HC161

5/16
M54/M74HC160/161/162/163

LOGIC DIAGRAM

HC162

LOGIC DIAGRAM

HC163

6/16
 M54/M74HC160/161/162/163

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
VCC Supply Voltage -0.5 to +7 V
VI DC Input Voltage -0.5 to VCC + 0.5 V
VO DC Output Voltage -0.5 to VCC + 0.5 V
IIK DC Input Diode Current ± 20 mA
IOK DC Output Diode Current ± 20 mA
IO DC Output Source Sink Current Per Output Pin ± 25 mA
ICC or IGND DC VCC or Ground Current ± 50 mA
PD Power Dissipation 500 (*) mW
o
Tstg Storage Temperature -65 to +150 C
o
TL Lead Temperature (10 sec) 300 C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Value Unit
VCC Supply Voltage 2 to 6 V
VI Input Voltage 0 to VCC V
VO Output Voltage 0 to VCC V
o
Top Operating Temperature: M54HC Series -55 to +125 C
o
M74HC Series -40 to +85 C
tr, tf Input Rise and Fall Time VCC = 2 V 0 to 1000 ns
VCC = 4.5 V 0 to 500
VCC = 6 V 0 to 400

7/16
M54/M74HC160/161/162/163

DC SPECIFICATIONS
Test Conditions Value
Symbol Parameter TA = 25 oC -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
VIH High Level Input 2.0 1.5 1.5 1.5
Voltage 4.5 3.15 3.15 3.15 V
6.0 4.2 4.2 4.2
V IL Low Level Input 2.0 0.5 0.5 0.5
Voltage 4.5 1.35 1.35 1.35 V
6.0 1.8 1.8 1.8
V OH High Level 2.0 1.9 2.0 1.9 1.9
VI =
Output Voltage 4.5 IO=-20 µA 4.4 4.5 4.4 4.4
VIH
V
6.0 or 5.9 6.0 5.9 5.9
4.5 V IL IO=-4.0 mA 4.18 4.31 4.13 4.10
6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60
VOL Low Level Output 2.0 0.0 0.1 0.1 0.1
VI =
Voltage 4.5 IO= 20 µA 0.0 0.1 0.1 0.1
VIH
V
6.0 or 0.0 0.1 0.1 0.1
4.5 V IL IO= 4.0 mA 0.17 0.26 0.33 0.40
6.0 IO= 5.2 mA 0.18 0.26 0.33 0.40
II Input Leakage VI = VCC or GND ±0.1 ±1 ±1 µA
6.0
Current
ICC Quiescent Supply 6.0 VI = VCC or GND 4 40 80 µA
Current

8/16
 M54/M74HC160/161/162/163

AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)

Test Conditions Value
o
Symbol Parameter TA = 25 C -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
tTLH Output Transition 2.0 25 75 95 110
tTHL Time 4.5 7 15 19 22 ns
6.0 6 13 16 19
tPLH Propagation 2.0 48 125 155 190
tPHL Delay Time 4.5 16 25 31 38 ns
(CLOCK - Q)
6.0 14 21 26 32
tPLH Propagation 2.0 57 150 190 225
tPHL Delay Time 4.5 COUNT MODE 19 30 38 45 ns
(CLOCK-CARRY)
6.0 16 26 32 38
tPLH Propagation 2.0 66 175 220 265
Delay Time 4.5 PRESET MODE 22 35 44 53 ns
(CLOCK-CARRY)
6.0 19 30 37 45
tPHL Propagation 2.0 72 200 250 300
Delay Time 4.5 PRESET MODE 24 40 50 60 ns
(CLOCK-CARRY)
6.0 20 34 43 51
tPLH Propagation 2.0 39 100 125 150
tPHL Delay Time 4.5 13 20 25 30 ns
(ENT-CARRY)
6.0 11 17 21 26
tPLH Propagation 2.0 for 60 150 190 225
Delay Time 4.5 HC160/161 20 30 38 45 ns
(CLEAR - Q) only
6.0 17 26 32 38
tPHL Propagation 2.0 for 72 200 250 300
Delay Time 4.5 HC160/161 24 40 50 60 ns
(CLEAR-CARRY) only
6.0 20 34 43 51
fMAX Maximum Clock 2.0 6.2 18 5 4.2
Frequency 4.5 31 53 25 21 MHz
6.0 37 62 30 25
tW(H) Minimum Pulse 2.0 18 75 95 110
tW(L) Width 4.5 6 15 19 22 ns
(CLOCK)
6.0 6 13 16 19
tW(L) Minimum Pulse 2.0 for 24 75 95 110
Width 4.5 HC160/161 7 15 19 22 ns
(CLEAR) only
6.0 6 13 16 19
ts Minimum Set-up 2.0 40 100 125 150
Time 4.5 10 20 25 30 ns
(LOAD, PE, TE)
6.0 8 17 21 26
ts Minimum Set-up 2.0 20 75 95 110
Time 4.5 5 15 19 22 ns
(A, B, C, D)
6.0 3 13 16 19
ts Minimum Set-up 2.0 for 20 75 95 110
Time 4.5 HC162/163 5 15 19 22 ns
(CLEAR) only
6.0 3 13 16 19

9/16
M54/M74HC160/161/162/163

AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)

Test Conditions Value
o
Symbol Parameter TA = 25 C -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
th Minimum Hold 2.0 0 0 0
Time 4.5 0 0 0 ns
(A, B - CK)
6.0 0 0 0
tREM Minimum 2.0 18 50 65 75
Removal Time 4.5 4 10 13 15 ns
6.0 3 9 11 13
CIN Input Capacitance 5 10 10 10 pF
CPD (*) Power Dissipation 50
pF
Capacitance
(*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC

SWITCHING CHARACTERISTICS TEST WAVEFORM

COUNT MODE CLEAR MODE (HC160/161)

PRESET MODE CLEAR MODE (HC162/163)

10/16
 M54/M74HC160/161/162/163

SWITCHING CHARACTERISTICS TEST WAVEFORM (continued)

COUNTENABLE MODE CASCADE MODE

(fix maximum count)

TEST CIRCUIT ICC (Opr.) TOTAL OPERATING CURRENT WHEN

USING A CAPACITIVE LOAD

When the outputs drive a capacitive load, the

total current can be calculated as follows :

For M74HC160/162 :
 Ca Cb Cc Cd Cca 
∆ lCC = fCK ⋅ VCC⋅  + + + + 
2 5 10 10 10 

For M74HC161/163 :
 Ca Cb Cc Cd Cca 
∆ lCC = fCK ⋅ VCC⋅  + + + + 
2 4 8 16 16 
Ca to C ca are the capacitors loading the out-
puts.

TYPICAL APPLICATION

11/16
M54/M74HC160/161/162/163

Plastic DIP16 (0.25) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

a1 0.51 0.020

B 0.77 1.65 0.030 0.065

b 0.5 0.020

b1 0.25 0.010

D 20 0.787

E 8.5 0.335

e 2.54 0.100

e3 17.78 0.700

F 7.1 0.280

I 5.1 0.201

L 3.3 0.130

Z 1.27 0.050

P001C

12/16
 M54/M74HC160/161/162/163

Ceramic DIP16/1 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 20 0.787

B 7 0.276

D 3.3 0.130

E 0.38 0.015

e3 17.78 0.700

F 2.29 2.79 0.090 0.110

G 0.4 0.55 0.016 0.022

H 1.17 1.52 0.046 0.060

L 0.22 0.31 0.009 0.012

M 0.51 1.27 0.020 0.050

N 10.3 0.406

P 7.8 8.05 0.307 0.317

Q 5.08 0.200

P053D

13/16
M54/M74HC160/161/162/163

SO16 (Narrow) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.004 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45° (typ.)
D 9.8 10 0.385 0.393
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 8.89 0.350
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.62 0.024
S 8° (max.)

P013H

14/16
 M54/M74HC160/161/162/163

PLCC20 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 9.78 10.03 0.385 0.395

B 8.89 9.04 0.350 0.356

D 4.2 4.57 0.165 0.180

d1 2.54 0.100

d2 0.56 0.022

E 7.37 8.38 0.290 0.330

e 1.27 0.050

e3 5.08 0.200

F 0.38 0.015

G 0.101 0.004

M 1.27 0.050

M1 1.14 0.045

P027A

15/16
M54/M74HC160/161/162/163

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.

 1994 SGS-THOMSON Microelectronics - All Rights Reserved

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A

16/16