Scribd
Upload
1K views20 pages

Automotive Multi-Function Circuit Tester With LCD QM1494 User Manual

This document provides instructions for using an automotive multi-function circuit tester with LCD. The tester can be used to test components by providing positive voltage and checking if LEDs change from green to red. It can also measure voltage on circuits without activating switches. Additionally, the tester can detect missing cylinders by sensing ignition pulses through capacitive coupling with spark wires and measure ignition pulse frequency in the same way. Proper procedures and schematics should be followed to avoid damaging components.

Uploaded by

John Bliudzius
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views20 pages

Automotive Multi-Function Circuit Tester With LCD QM1494 User Manual

This document provides instructions for using an automotive multi-function circuit tester with LCD. The tester can be used to test components by providing positive voltage and checking if LEDs change from green to red. It can also measure voltage on circuits without activating switches. Additionally, the tester can detect missing cylinders by sensing ignition pulses through capacitive coupling with spark wires and measure ignition pulse frequency in the same way. Proper procedures and schematics should be followed to avoid damaging components.

Uploaded by

John Bliudzius
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 20

Automotive Multi-Function Circuit Tester

with LCD
QM1494
User Manual
Instruction
retset otua Manual
lanoitcnufor
f-itthe
luM Multi-functional
eht rof launaM noauto
itcurttester
snI

12. Activate components with positive voltage only


When technician tests the components, technician can use tester to provide positive
voltage to the testing components. To do this, please follow the procedure:
1. Contact the tester tip with the positive pole of the components. If the green LED is
on, it means the testing component is conductible.
2. As the green LED goes on ,please press the polar switch forward and then release
it quickly. If the LED goes from green to red LED ,you may proceed further testing.
If the green LED turns off and red LED doesn’t turns on, or if the circuit breaker of
the short circuit protection tripped, it means tester has overloaded. This may due
to the following reasons:
The component is short circuit or it has been connected to the ground/negative
pole directly.
The component is a high current component.
If the circuit breaker of the short circuit protection has tripped, it will auto-rest within
no more than 60 seconds.

13. Important
Please operate this function with schematic and correct testing procedure because
applying voltage arbitrarily may cause damage to components.Use tip to apply
positive voltage ,which can be helpful to diagnose the components.

Motor

11
Instruction Manual
Instruction Manualfor
forthe
theMulti-functional autotester
Multi-functional auto tester

18.Voltage Test
Technician can also use tester assisting with ground tese the voltage of the circuit.
However ,during the voltage test, please do not push the polar switch.
1. If the probe tip is floating (not contacting a circuit),the red and green LED turn off .
2. If the tester contact the probe tip to a positive circuit . The red positive sign “+”
LED will light and the voltmeter displays the voltage reading within 1/10th of a volt.
3. If the tester contact the probe tip to a negative circuit. The green negative sign “-”
LED will light.

19.Locate missing cylinders


Placing the tester probe tip next to a sparking wire(DON’T probing it directly), through
capacitive coupling, the tester can senses the high-tension ignition pulses at the
same time display a voltage reading. By monitoring each plug wire in this way you
can locate missing cylinders.

Warning: DO NOT CONTACT PROBE TIP DIRECTLY


TO THE SECONDARY IGNITION CIRCUIT.

20. Measuring the frequency of the high-tension ignition pulses


The tester can measure the frequency of the high –tension ignition pulses. Placing
the tester probe tip next to a sparking wire(DO NOT probing it directly),through
capacitive coupling, the tester can senses the high –tension ignition pulses at the
same time display a frequency reading.

14
Instruction
retset otua Manual
lanoitcnufor
f-itthe
luM Multi-functional
eht rof launaM noauto
itcurttester
snI

1. MEASURING METHOD
(1). -cylinder gasoline engine

High-ttension wire

lgnition plug

(2). Distributor type multi –cylinder gasoline engine

lgnition plug

13
15
Instruction Manual
Instruction Manualfor
forthe
theMulti-functional autotester
Multi-functional auto tester

Where all the high-tension wires of cylinders are bundled together

High-tension wire connecting distributor and ignition coil.


As shown in the figure A,B, bring the detection head close to the high-tension wire
that connect the distributor and the ignition coil, or to the place where all the
high-tension wires of the cylinders are together.

(3). Multi-cylinder gasoline engine without distributor


Bring the detection head close to the place where the high-tension wire of each cylinder
is bundled together.
The measurement is impossible if all the high-tension wires are not bundled
together since the distance between the detection head and each high-tension wire differs.

3
161

You might also like