TechWest Liner Equipment

CEMENTED LINER
SYSTEMS
TECHWEST LINERS
Doc#: F.5.6.2
Rev: 1-1
Date: Dec 2018
Doc No. F.5.6.2, Rev 1-1, Dec 2018 techwesttools.com Made in Canada
1
TABLE OF CONTENTS
CEMENTED LINER HANGER
HANGER SYSTEMS ................................................................
................................................................................................
...........................................................................
........................................... 4
LINER LAP PACKER, ROTATIONAL LLPR ................................................................................................................................ 6
LINER LAP PACKER, NON-ROTATIONAL (LLP) ....................................................................................................................... 7
DEEP SERVICE LINER TOP PACKER™ ..................................................................................................................................... 8
HYDRAULIC DOVETAIL LINER HANGER (HDLH) ..................................................................................................................... 9
HYDRAULIC DOVETAIL ROTATING LINER HANGER (HDRLH) ................................................................................................. 9
MECHANICAL SET LINER HANGER (MSLH) .......................................................................................................................... 10
MECHANICAL DOVETAIL SLIP HANGER (MDSH) ................................................................................................................. 11
MECHANICAL DOVETAIL ROTATING SLIP HANGER (MDRSH) .............................................................................................. 11
SETTING COLLAR, ROTATIONAL (SC-R) ................................................................................................................................ 12
SETTING COLLAR, NON-ROTATIONAL (SC-NR) .................................................................................................................... 12
TIEBACK RECEPTACLE (TBR) ................................................................................................................................................ 13
TIEBACK SEAL NIPPLE (TBSN) ............................................................................................................................................. 14
TIE BACK LATCH SEAL ASSEMBLY ....................................................................................................................................... 15
POSI-LATCH TIE-BACK FRAC SEAL ........................................................................................................................................ 16
STAGE COLLAR (SC) ............................................................................................................................................................ 17
HYDRAULIC LANDING COLLAR (HLC) .................................................................................................................................. 18
MECHANICAL PLUG LANDING COLLAR (MPLC) ................................................................................................................... 18
DRILL PIPE WIPER PLUG (DPWP) ........................................................................................................................................ 19
LINER WIPER PLUG (LWP) .................................................................................................................................................. 19
DRILLABLE BALL SEAT COLLAR (DBSC) ................................................................................................................................ 20
RETRIEVABLE PACK-OFF BUSHING (RPOB) ......................................................................................................................... 21
DRILLABLE PACK OFF BUSHING (DPOB) .............................................................................................................................. 21
DRILLABLE PACK OFF BUSHING w/ FLAPPER VALVE (DPOB/F)............................................................................................. 21
FLOAT COLLAR (SVFC / DVFC) ............................................................................................................................................ 22
VALVE FLOAT SHOE ........................................................................................................................................................... 22
INDEX SUB WITH ECCENTRIC NOSE (ISEN) ......................................................................................................................... 23
SURGE PROTECTION TOOL (SPT) ........................................................................................................................................ 24
LINER SWIVEL (LS).............................................................................................................................................................. 25
RECIRCULATING COLLAR (RCC) .......................................................................................................................................... 26
CEMENTED LINERS RUNNING

RUNNING EQUIPMENT ................................................................
................................................................................................
................................................................ 27
MECHANICAL ROTATING LINER RUNNING TOOL (MRLRT) .................................................................................................. 29
MECHANICAL LINER RUNNING TOOL (MLRT) ..................................................................................................................... 30
HYDRAULIC RELEASE RUNNING TOOL ................................................................................................................................ 31
ROTATING SETTING DOG (RSD).......................................................................................................................................... 32
HANDLING JOINT (HJ) ........................................................................................................................................................ 33
SCREENED AND PLATE DEBRIS BARRIER (SDB / PDB) ......................................................................................................... 34
CEMENTING SEAL JOINT (CSJ) ............................................................................................................................................ 35
CEMENTED LINERS REMEDIAL

REMEDIAL EQUIPMENT ................................................................
...............................................................................................
............................................................... 36
LINER TIE-BACK PACKER, ROTATIONAL (LTBPR) ................................................................................................................. 38
TIEBACK RECEPTACLE POLISHING MILL (TBRP) ................................................................................................................... 39
2
CEMENTED LINERS SURFACE
SURFACE EQUIPMENT ................................................................
................................................................................................
.................................................................
................................. 40
TOP DRIVE CEMENT HEAD (TDCH) ..................................................................................................................................... 42
TOP DRIVE CEMENT HEAD SKID ......................................................................................................................................... 43
KELLY RIG CEMENT HEAD (KRCH) ....................................................................................................................................... 44
FLAG SUB (FS) .................................................................................................................................................................... 45
CEMENTED LINERS ACCESORIES

ACCESORIES ................................................................
................................................................................................
................................................................................
................................................ 46
NON-WELDED BOWSPRING CENTRALIZERS ....................................................................................................................... 48
NON-WELDED POSITIVE CENTRALIZERS ............................................................................................................................. 48
NON-WELDED TURBOLIZER CENTRALIZER.......................................................................................................................... 49
LINER CENTRALIZER ........................................................................................................................................................... 49
CEMENTING PLUGS ............................................................................................................................................................ 50
ALUMINIUM CORE CEMENTING PLUGS ............................................................................................................................. 50
DEPTH ORIENTATION COLLAR ........................................................................................................................................... 51
BELL NIPPLE ....................................................................................................................................................................... 51
PRODUCTION CASING CAP................................................................................................................................................. 51
BAFFLE COLLAR .................................................................................................................................................................. 51
BAFFLE PLATE .................................................................................................................................................................... 51
OPENHOLE LINER SYSTEMS

SYSTEMS ................................................................
................................................................................................
........................................................................................
........................................................ 52
LINER ANCHOR PACKER (LAP) ............................................................................................................................................ 54
HYDRAULIC ROTATING LINER RUNNING TOOL................................................................................................................... 55
HYDRAULIC MECHANICAL LINER RUNNING TOOL .............................................................................................................. 56
SETTING PLUG ................................................................................................................................................................... 57
OPEN HOLE HYDRAULIC INTERVAL PACKER ....................................................................................................................... 58
HYDRAULIC FRAC SLEEVE ................................................................................................................................................... 58
LOWER HYDRAULIC FRAC SLEEVE ...................................................................................................................................... 59
HCBS HYDRAULIC CLOSING BALL SEAT ............................................................................................................................... 59
DEEP SERVICE TOP SEAL™ .................................................................................................................................................. 60
DEEP SEAL ANCHOR PACKER™ ........................................................................................................................................... 61
DEEP SEAL ANCHOR™ ........................................................................................................................................................ 61
TANDEM SEAL OPEN HOLE PACKER .................................................................................................................................... 62
THERMAL LINER SYSTEMS

SYSTEMS ................................................................
................................................................................................
..........................................................................................
.......................................................... 63
LINER THERMAL PACKER – RETRIEVABLE AND ROTATIONAL ............................................................................................. 65
LINER SAGD PACKER, ROTATIONAL (LSPR) ........................................................................................................................... 66
LINER THERMAL EXPANSION JOINT (LEJ) ........................................................................................................................... 67
MECHANICAL OPENHOLE THERMAL PACKER (MOHT) ........................................................................................................ 68
TIE BACK LATCH ASSEMBLY ................................................................................................................................................. 69
THERMAL CUP STRADDLE / PACKER .................................................................................................................................. 70
HYDRAULIC ROTATING LINER RUNNING TOOL................................................................................................................... 71
3
CEMENTED
LINER HANGER
SYSTEMS
4
CEMENTED LINER
SYSTEMS
Many of TechWest’s new tool innovations come from customer requests. As a design and manufacturing
company we are constantly in pursuit of new tools and innovations and we encourage anyone to contact us with
such enquiries and requests.
Reg. No. 2995

ISO 9001:2015
®
Reg. No. 11D1-0124 Reg. No. Q1-2959

TechWest Products and Services are provided under a management system registered to API Spec Q1 and ISO 9001:2015 and TechWest holds a Monogram licence
for API Spec 11D1 for Packers and Bridge Plugs.
The illustrations used in this catalogue are schematics only, so the actual product may not be exactly as illustrated.
The product information contained in this catalogue is of a general nature only and is subject to change without notice.
For the most specific and detailed technical information please contact TechWest directly.
TechWest Products and Services are subject to TechWest’s standard Terms and Conditions. Unless otherwise noted,
trademarks, servicemarks noted herein are the property of TechWest.
5
CEMENTED LINER
SYSTEMS
LINER LAP PACKER, ROTATIONAL LLPR

UNIT 100
The TechWest Liner Lap Packer, Rotational (LLPR) is a versatile 10K liner packer used
in numerous applications. It is most often placed at the top of a liner which is to be
cemented. Setting the LLPR after cementing allows the operator to reverse excess
cement out of the hole without exerting pressure on formations below the top of the liner
and prevents gas migration through the cement as it is setting up.
The LLPR employs castellation’s on the top of the tool allowing the liner system to be
rotated (to the right). This feature provides additional means of working the pipe to depth
and allows for rotation during cementing to flow condition the cement during the cement
job.
The LLPR is available with or without hold-down slips and comes with standard reinforced
HNBR rubber pack-offs, TWL Premium Seal Pack-Off or other special high-temperature
pack-offs upon request.
The LLPR is available with either internal Retrievable Pack-Off Bushing (RPOB) profile or
Drillable Pack-Off-Bushing (DPOB) threading.
The Liner Packer provides the threaded connection for any standard length 122-Tieback
Receptacle
Customizable for licensed premium threading or materials.
OPERATION
The LLPR is run with a type MR (Rotational) Setting Tool screwed into its barrel using a
left-hand thread and floating nut. When setting the packer, the setting tool is released by
right-hand rotation and picked up allowing the setting dogs to expand and catch the top
sleeve of the LLPR packer. The setting tool is then lowered, forcing the sleeve down-ward
and expanding the packoff to set the packer. A ratchet ring in the LLPR holds the packoff
in the expanded position.
When used to set a screen, the type LLPR (without hold-down slips) may be retrieved by
running a spear to catch the inner barrel.
A wide variety of optional configurations are available upon request.
6
CEMENTED LINER
SYSTEMS
LINER LAP PACKER, NON-ROTATIONAL (LLP)

UNIT 101
The TechWest LLP Liner Lap Packer, Non-Rotational (LLP) is a versatile 10K liner
packer used in numerous applications. It is most often placed at the top of a liner which
is to be cemented. Setting the type LLP after cementing allows the operator to reverse
excess cement out of the hole without exerting pressure on formations below the top of
the liner and prevents gas migration through the cement as it is setting up.
The LLP is available with or without hold-down slips and comes with standard reinforced
HNBR rubber pack-offs, TWL Premium Seal Pack-Off or other special high-temperature
pack-offs upon request.
The LLP is available with either internal Retrievable Pack-Off Bushing (RPOB) profile or
Drillable Pack-Off-Bushing (DPOB) threading.
The Liner Packer provides the threaded connection for any standard length 122-Tieback
Receptacle
Customizable for licensed premium threading or materials.
OPERATION
The LLP is run with a M Setting Tool screwed into its barrel using a left-hand thread and
floating nut. When setting the packer, the setting tool is released by right-hand rotation
and picked up allowing the setting dogs to expand and catch the top sleeve of the LLP
packer. The setting tool is then lowered, forcing the sleeve down-ward and expanding the
packoff to set the packer. A ratchet ring in the LLP holds the packoff in the expanded
position.
When used to set a screen, the type LLP (without hold-down slips) may be retrieved by
7
CEMENTED LINER
SYSTEMS
DEEP SERVICE LINER TOP PACKER™

UNIT 681
The TechWest Deep Service Liner Top Packer is designed with a focus on Multi-Zone
Fracturing applications, the Deep Service Liner Top Packer™ is a High Temperature / High
Pressure thermal variation of the proven and reliable TechWest Liners Liner Lap Packer
tool platform.
It is designed to be delivered downhole on the model HR Hydraulic Rotating Running Tool

with the HydroAct™ (Hydraulic Actuator) for non-cemented applications. The HR running
tool can push, pull and rotate to the right delivering the liner through challenging structure
on the way to depth.
The Deep Service Top Seal packer may be set-up in numerous configurations to suit
operational requirements. There are versions without slips, hold-up and -down slips.
For thermal applications it is usually dressed with SoftSet® sealing elements rated to 600
o
F @ 3,000 psi. For non-thermal applications there is the opportunity to dress the packer
with Nitrile, HNBR or HT/HP (High Pressure / High Temperature) Ecner Array® sealing
elements.
While L80 metallurgy is the standard offering, other materials are readily available to meet
operational needs. Economical setting sleeves or polished bore Tieback Receptacles
maybe provided in a variety of lengths.
The Deep Service Top Seal packer also comes in a retrievable version with hold-up and -
down slips.
OPERATION
At depth, a plug is pumped to seat allowing pressures to be built-up in the drill pipe. At a
predetermined pressure, the packer is set, and annular tests can be conducted to verify
element sealing integrity. A further increase in pressure releases the running tool. When
the running tool is pulled from the Deep Service Top Seal packer, a set of ports are
exposed allowing the drill pipe to be drained as it is pulled out of the hole.
8
CEMENTED LINER
SYSTEMS
HYDRAULIC DOVETAIL LINER HANGER (HDLH)

UNIT 124
HYDRAULIC DOVETAIL ROTATING LINER HANGER (HDRLH)

UNIT 125
The TechWest Hydraulic Dovetail Liner Hanger (HDLH) is a premium liner hanger with
an integral body. The hanger mandrel is machined from heavy wall mechanical tubing and
treated to the required grade. Integral construction eliminates all internal connections
which provide maximum pressure ratings and liner hanging capacity. The cones have
milled channels providing a superior bypass for circulation of fluids and cementing.
The hanger is shear pinned to prevent premature setting. The shear rate is variable and
field adjustable according to operational parameters dictated by well conditions.
The TechWest Hydraulic Dovetail Rotating Liner Hanger (HDRLH) can be rotated into
place, set and then rotated through the liner cementing operation.
FEATURES
Enhanced fluid bypass with pocket slip design.

Long pocket type dovetail slip for long heavy liners.
Faster running speed with pocket slip design.
Castellation clutch in setting collar allows for rotating of liner through tight hole spots.
Manufactured from mechanical tubing of equivalent liner grade; 80,000 psi is
standard, other yield strengths and materials available by special order
Slips manufactured to 55-60 Rockwell “C” hardness for high-grade casing
compatibility.
OPERATION
The HDLHP is set hydraulically while building up pressure against the Hydraulic Landing
Collar.
9
CEMENTED LINER
SYSTEMS
MECHANICAL SET LINER HANGER (MSLH)

UNIT 116
The TechWest Mechanical Set Liner (MSLH) is economical liner hanger, used to
suspend cemented and uncemented liners off bottom. Designed for heavy duty service,
they are capable of successfully suspending long liners.
The MSLH is available with a one-piece integral barrel for maximum pressure integrity.
Large bypass lessens pressure build-up during run-in and cementing operations.
The MSLH is set by picking up on the liner and rotating to disengage the J-Slot. When the
MSLH is lowered the springs hold the cage stationary. This allows the barrel to move
downward engaging the cone against the slips. This action moves the slips outward
against the casing wall.
The MSLH are available in right hand set only.
FEATURES
Economical slip design

standard, other yield strengths and materials available by special order
compatibility.
OPERATION
The MSLH is set mechanically by drill pipe manipulation. Disengage the latch housing and
set down with right hand rotation.
10
CEMENTED LINER
SYSTEMS
MECHANICAL DOVETAIL SLIP HANGER (MDSH)

UNIT 144
MECHANICAL DOVETAIL ROTATING SLIP HANGER (MDRSH)

UNIT 145
The TechWest Mechanical Dovetail Slip Hanger (MDLH & MRDLH) is a premium
hanger with an integral body. The hanger mandrel is machined from heavy wall
mechanical tubing and treated to the required grade. Integral construction eliminates all
internal connections which provide maximum pressure ratings and liner hanging capacity.
Once in position, the Mechanical Dovetail Rotating Slip Hanger (MDRSH) can be
rotated through the liner cementing operation.
FEATURES
Enhanced fluid bypass with dovetail design.

Long recessed type dovetail slips for long heavy liners.
Faster running speed with dovetail design.
standard, other yield strengths and materials available by special order.
compatibility.
OPERATION
The MDSH is set mechanically by drill pipe manipulation. Disengage the latch housing
and set down with right hand rotation.
11
CEMENTED LINER
SYSTEMS
SETTING COLLAR, ROTATIONAL (SC-R)

UNIT 107
The TechWest Setting Collar, rotational (SC-R) is designed for use with either rotating
and/or all right-hand set liner assemblies. The SC-R Setting Collar can also be used to
carry bottom liners into place and then set on bottom.
FEATURES
Top clutch allows for right hand set hangers to be set.

Top clutch allows operator to work liner into place in a deviated well bore, as well as
work the casing into place if hole fill is encountered.
Suitable for applications where a liner top packer is not required
Customizable for licensed premium threading or materials
SETTING COLLAR, NON-ROTATIONAL (SC-NR)

UNIT 108
The TechWest Setting Collar, non-rotational (SC-NR) is used to carry short drop off
liners or screens to bottom where it is not necessary to use a liner hanger to suspend the
liner weight.
FEATURES
Drop off liner in open-hole to keep the hole open.

Drop of liner screens where liner top packer or hangers are not needed.
Suitable for applications where a liner top packer is not required
Customizable for licensed premium threading or materials
12
CEMENTED LINER
SYSTEMS
TIEBACK RECEPTACLE (TBR)

UNIT 122
The TechWest Tie-Back Receptacle (TBR) is run as an integral part of the liner
or casing string. It is a honed and/or coated receptacle that allows the tubing
string to contract and/or expand in response to pressure and temperature, while
maintaining the high degree of sealing capability.
The TBR is normally installed above a Liner Lap Packer or Setting Collar.
The honed inside surface of the TBR can be coated to prevent cement or other
material from adhering. This coating minimizes corrosion caused by metal-to-
metal contact and well effluents.
FEATURES
Comes is standard length ranging from 6 to 20 feet

Allows tie-back to surface with a Tie-Back Seal Nipple.
Can set Tie-back Packer into for remedial operations.
Honed finish internal diameter.
Top profile for plate or screen debris barriers to prevent abrasive internal
damage
Suitable for TechWest top dress and bore polishing mills
13
CEMENTED LINER
SYSTEMS
TIEBACK SEAL NIPPLE (TBSN)

UNIT 140
The TechWest Tieback Seal Nipple (TBSN) has proven to be a superior method of
extending the liner to the surface of the well. Using the polished bore receptacle
of the Setting Collar (SC) or the Liner Lap Packer (LLPH) packer, this assembly
facilitates the entry and subsequent seal of the nipple into the bore.
The TBSN is run at the bottom of the liner extension. Depending on the
application, it employs either a premium Aflas or Chevron-type unitized seal
assembly, or a series of o-rings. Both designs deliver a solid seat and permanent
seal.
The orifice collar normally included in the liner extension assembly is positioned
one joint above the seal nipple. This prevents hydraulic blockage as the seal is
engaged in the receptacle and allows the liner extension to fill at a predetermined
rate as it is run. The orifice collar also serves as a stop for the cement plug and is
constructed of drillable materials.
FEATURES
Provides a high-pressure seal at the liner top

Extends a liner to the surface
Allows a PBR-type completion after the liner has been set and cemented by
mounting a PBR above it.
14
CEMENTED LINER
SYSTEMS
TIE BACK LATCH SEAL ASSEMBLY

UNIT 321
The TechWest Tie Back Latch Seal Assembly (TBLSA) is used to connect the
work string to a previously run liner down hole and provide a high-pressure seal
to the system. It is disconnected from the liner with right hand rotation.
FEATURES
High pressure latch seal assembly

Premium seal stack configurations available for high pressure and high
temperature applications
Ease of entry into tie-back receptacle or setting collar combined with high
tensile load capabilities.
15
CEMENTED LINER
SYSTEMS
POSI-LATCH TIE-BACK FRAC SEAL

UNIT 699
The TechWest Posi-Latch Tie-Back Frac Seal provides a high pressure seal
while anchoring the frac string to the packer. It is used to lock the fracturing string
to the liner top packer prior to pumping. The Posi-Latch will keep your tubing in
tension until you release it.
The Positive Tie Back Latch Assembly is often used with the Deep Service Top
Seal Packer™.
16
CEMENTED LINER
SYSTEMS
STAGE COLLAR (SC)

UNIT 260
The TechWest Stage Collar (SC) hydraulically opened stage cementing tool is
used to stage cement into the annulus over specific intervals. Staging cement is
done where weak formations will not support the hydrostatic column of annular
cement. This can occur when large volumes of cement are needed, and pumping
time may become an issue, or when specific placement of cement over an interval
is required.
FEATURES
Provides improved zonal isolation

Available in multiple materials and connections.
Hydraulically or Mechanical Set
Easily adjustable setting pressure on location.
Multiple bomb and pressure dart configurations available.
OPERATION
In the hydraulic configuration the SC is set by pressure build up in the liner string.
In the mechanical configuration the SC is set by a gravity bomb dropped from
surface.
A predetermined amount of cement is then pumped through large cementing

ports. The closing wiper dart then hydraulically closes the ports reestablishing
liner pressure integrity.
17
CEMENTED LINER
SYSTEMS
HYDRAULIC LANDING COLLAR (HLC)

UNIT 114
The TechWest Hydraulic Landing Collar (HLC) has an internal ball seat and is
run with a Hydraulic Dovetail Liner Hanger (HDLH). The HLC is run two or three
joints from the shoe and is used to land the Liner Wiper Plugs (LWP).
The LWP provides a pressure seal from above and below and are easily PDC
drillable.
FEATURES
Used to set a wide variety of hydraulic liner systems

Aluminum internals for easy milling
Locks the Liner Wiper Plug and Drill Pipe Wiper Plug.
Extremely reliable primary setting technology.
Available in standard and premium connections.
MECHANICAL PLUG LANDING COLLAR (MPLC)

UNIT 117
The TechWest Mechanical Plug Landing Collar (MPLC) is run two or three joints
from bottom and is used to land the Liner Wiper Plug (LWP).
The LWP provides a pressure seal that holds pressure from above and below and
are easily PDC drillable.
FEATURES
Used to set a wide variety of mechanical liner systems

Aluminum internals for easy milling
Locks the Liner Wiper Plug and Drill Pipe Wiper Plug.
18
CEMENTED LINER
SYSTEMS
DRILL PIPE WIPER PLUG (DPWP)

UNIT 111
The TechWest Drill Pipe Wiper Plug (DPWP) follows the cement, separating
the cement from displacement fluid. The plug employs a series of rubber fins
of varied sizes to wipe the inside of the cement head, setting string, tool joints,
and liner setting tool. It is designed to latch and seal securely into the liner
wiper plug. The two plugs then move as one through the liner to latch into the
landing collar.
FEATURES
Wipes the drill string clean after cementing operations.

Lands and securely locks into the Liner Wiper Plug
LINER WIPER PLUG (LWP)

UNIT 112
The TechWest Liner Wiper Plug (LWP) is shear pinned to the shear out
adaptor at the bottom of the 121-Cementing Seal Joint below the setting tool.
It is designed to receive the 111-Drill Pipe Wiper Plug. The two plugs then
move through the liner keeping the mud separated from the cement while it
wipes the liner ID clean. When the liner wiper plug seats in the landing collar,
it latches and forms a pressure seal that holds securely from either direction.
The plug is also designed to clutch in the 114-Hydraulic Landing Collar to
prevent rotation during drill out.
FEATURES
Wipes the liner clean after cementing operations.

Lands and securely locks into the landing collar
19
CEMENTED LINER
SYSTEMS
DRILLABLE BALL SEAT COLLAR (DBSC)

UNIT 133
The TechWest Drillable Ball Seat Collar (DBSC) can be used anywhere where
it is desired to plug the bottom of the casing for any reason to ether set hydraulic
equipment above or inflate packers that requires the plugging of the casing string.
The Drillable Ball Seat Collar is used to set Inflatable packers, open hydraulic
stage tools and set most hydraulic equipment.
FEATURES
Can be setup for high pressure setting capability

Used in a wide variety of hydraulic or mechanical liner systems
Locking aluminum internals for easy milling
20
CEMENTED LINER
SYSTEMS
RETRIEVABLE PACK-OFF BUSHING (RPOB)

UNIT 120
The TechWest Retrievable Pack-Of Bushing (RPOB) is used to pack off and
maintain a high-pressure seal inside the SSR receptacle for cementing and
circulating operations. The RPOB is normally installed into the top of the Liner
Lap Packer and is retrieved when setting equipment is pulled.
FEATURES
Provides positive seal of liner setting tools

No need to drill out pack-off bushing
Redressable
DRILLABLE PACK OFF BUSHING (DPOB)

UNIT 110
The TechWest Drillable Pack-off Bushing (DPOB) is a high pressure,

high-temperature pack-off used when working with high angle well bores.
The DPOB has chevron type packing that seal tightly around the polished
Cementing Seal Joint (Unit 121). The DPOB hold pressure from above and
below and is not damaged from rotation during setting and releasing of
liners.
DRILLABLE PACK OFF BUSHING W/ FLAPPER VALVE (DPOB/F)

UNIT 126
The TechWest Drillable Pack-off Bushing with Flapper Valve

(DPOB/F) is a high pressure, high-temperature pack-off used when
working with high angle well bores. The component is like the DPOB
except with a flapper acting an extra float that closes when the Cementing
Seal Joint is removed,
21
CEMENTED LINER
SYSTEMS
FLOAT COLLAR (SVFC / DVFC)

UNIT 250 / 255
The TechWest Single Valve Float Collar (SVFC) and Double Valve Float Collar
(DVFC) act as extra back pressure valves, sealing against pressure from below
when floating in a liner or casing. The spring-loaded ball and seat valve(s) ensure
a secure seal. The SVFC and DVFC have no internal connections and is highly
resistant to abrasive fluids, corrosion, and temperature.
VALVE FLOAT SHOE

UNIT 251 / 253
The TechWest Single Valve Float Shoe, Spaded Nose (SVFS-SN) and Double
Valve Float Shoe, Spaded Nose (DVFS-SN) is a check-valve ran on the bottom
of the casing. Spring-loaded ball and seat back-pressure valve(s) prevent annular
fluid from entering the casing string and are highly resistant to abrasive fluids,
corrosion, and temperature. The tool features a spaded nose that assists in
getting the string to depth and down-jets used to facilitate wash down during
running operations which are employed when liners are set on bottom, improving
the cementing process.
The SVFS and DVFS-SN are designed to be easily PDC drillable.
FEATURES
Used in a wide variety of hydraulic or mechanical liner systems

Locking aluminum internals for easy milling
22
CEMENTED LINER
SYSTEMS
INDEX SUB WITH ECCENTRIC NOSE (ISEN)

UNIT 333
The TechWest Index Sub with Eccentric Nose (ISEN) will rotate the shoe
clockwise 180° degrees with each up and down movement of the work string at
surface. This rotation will assist the liner through tight spots in the well bore and
help get the liner to bottom.
FEATURES
Enhanced fluid bypass with dovetail design.

Long recessed type dovetail slips for long heavy liners.
Faster running speed with dovetail design.
standard, other yield strengths and materials available by special order.
compatibility.
23
CEMENTED LINER
SYSTEMS
SURGE PROTECTION TOOL (SPT)

UNIT 272
The TechWest Surge Protection Tool (SPT) allows the reduction of the effect of
fluid surging the formation on close tolerance annulus or weak formations that
may break down on hydraulic ball shear out used to set liner hangers.
FEATURES
Drastically reduces the risk of formation damage.

Available to suit TechWest HPHT Liner Systems
Keeps sudden pressure changes away from high risk areas.
Evenly distributes burst pressure through high flow ports
Ball drop configuration
OPERATION
The SPT is hydraulically operated with a setting ball.
24
CEMENTED LINER
SYSTEMS
LINER SWIVEL (LS)

UNIT 135
The TechWest Liner Swivel (LS) is used when long mechanical liners are run into
deviated wells or through tight sections in the well bore. The liner swivel is ran
further down the liner system and allows for the right hand rotation needed to
disengage the “J” from its slot to allow for the hanger setting process.
FEATURES
Used when liner rotation is required for deep or horizontal liner systems
Available in multiple materials and connections.
Heavy duty compression and tension ball bearings
Rotational capabilities under extreme load
25
CEMENTED LINER
SYSTEMS
RECIRCULATING COLLAR (RCC)

UNIT 113
The TechWest Recirculating Collar (RCC) is used with inner string circulating
strings to circulate screens and slotted casing into place. The pack-off is easily
drilled out with PDC bits, if necessary.
The RCC provides a positive seal to the end of the liner string allowing fluids to
be pumped to the liner toe.
FEATURES
Provides the ability to float in liner assemblies.

Compact high-pressure pack-off design.
Suitable for any liner length
Compact high-pressure pack-off design.
Ideal for long horizontal liner systems
26
CEMENTED LINERS
(RUNNING)
CEMENTED
LINERS RUNNING
EQUIPMENT
27
CEMENTED LINERS
(RUNNING)
company we are constantly in pursuit of new tools and innovations and we encourage anyone to contact us
with such enquiries and requests.
Reg. No. 2995

ISO 9001:2015
®
Reg. No. 11D1-0124 Reg. No. Q1-2959

TechWest Products and Services are provided under a management system registered to API Spec Q1 and ISO 9001:2015 and TechWest holds a Monogram
licence for API Spec 11D1 for Packers and Bridge Plugs.
28
CEMENTED LINERS
(RUNNING)
MECHANICAL ROTATING LINER RUNNING TOOL (MRLRT)

UNIT 200
The TechWest Mechanical Rotating Liner Running Too (MRLRT) has been
designed to be run with LLP (Unit 100), or the Liner Setting Sleeve that are used
with hydraulic or mechanical rotatable liner hangers for all vertical or horizontal
liner applications. Right hand rotation releases the tool from the liner and is
retrieved with the drill pipe at the end of the cementing or dropping off the liner.
FEATURES
Can be pushed, pulled and rotated to get the liner into position.
Heavy duty construction for long term service use.
Inner circulating string can be used when screen deployment is needed.
Can be used in long ERD systems.
Can be used when drilling down of liner systems
29
CEMENTED LINERS
(RUNNING)
MECHANICAL LINER RUNNING TOOL (MLRT)

UNIT 210
The TechWest Mechanical Liner Running Tool (MLRT) is used to run

and set liner into the well bore. It is used to set left hand mechanical liner
hangers and hydraulic liner systems. Right hand rotation releases the tool
from the liner and is retrieved with the drill pipe at the end of the
cementing or dropping off the liner.
The TechWest Mechanical Liner Running Tool with Dogs (MLRWD)

will set all compression-set Liner Packers. It combines the features of the
type MLRT Running Tool with a spring-loaded, rotatable setting-dog
section that allows the setting force to be transmitted to the packer. When
activated, the spring-loaded setting-dog section permits setting force to
be transmitted to the packer, while the bearing allows the work string to
be rotated at the surface, thus transmitting additional weight to the
packer. Both features can be beneficial in high angle, or horizontal well
bores when attempting to weight-set a liner-top packer.
30
CEMENTED LINERS
(RUNNING)
HYDRAULIC RELEASE RUNNING TOOL

UNIT 220
The TechWest Hydraulic Release Running Tool (HR) is used to run in vertical and long
reach horizontal well bores. It is hydraulically set and released and can push, pull and
rotate the liner without the need of major work string manipulation. The HR setting tool
has an internal pack off and full open ID that allows for the circulation of well bore fluids.
FEATURES
The hydraulic release eliminates string weight free point requirements.
Can be used when drilling down of liner systems
31
CEMENTED LINERS
(RUNNING)
ROTATING SETTING DOG (RSD)

UNIT 127
The TechWest Rotating Setting Dog (RSD) is used whenever compressions set
liner packers are run. The dogs are spring loaded in the collapsed position while
the liner is being run and cemented. When released from the setting sleeve, set
down weight is applied to compress the liner packer. Bearing race in the RSD is
used to transfer additional weight in high angle well bores.
FEATURES
Heavy duty swivel for reliable service use
High tensile springs for reliable setting with compression on setting dogs
32
CEMENTED LINERS
(RUNNING)
HANDLING JOINT (HJ)

UNIT 128
The TechWest Handling Joint (HJ) is used with the setting tool and the setting
dogs. It is made up to the setting tools and consists of either 3-1/2” or 4-1/2” drill
pipe, with IF connections. The handling joint transitions the liner over to the drill
pipe that is used to run the liner into position.
FEATURES
Available with a wide variety of drill stem connections

Suitable for 6FT, 10Ft, 15FT, or 20FT Tie-Back Receptacles
Connects directly to the liner running tools
33
CEMENTED LINERS
(RUNNING)
SCREENED AND PLATE DEBRIS BARRIER (SDB / PDB)

UNIT 130 / 132
The TechWest Screened Debris Barrier (SDB) and TechWest Plate Debris
Barrier (PDB) sit on the top of a Tieback Receptacle (TBR) to prevent debris from
entering the polished bore. The debris barrier is connected to a setting tool and
is moveable on the setting tool permiting the setting tool to be stroked inside the
liner hanger assembly. During normal operations, such as cementing, the debris
screen remains at the top of the tieback receptacle except during the final stages
of retrieval.
FEATURES
Economical PDB design for all standard applications

Reduces risk in cemented liner installations
High filtration capability SDB design for small particulate wellbores
Keeps abrasive materials out of the polished tieback receptacle
34
CEMENTED LINERS
(RUNNING)
CEMENTING SEAL JOINT (CSJ)

UNIT 121
The TechWest Cementing Seal Joint (CSJ) is made up with the liner setting tool
using a CSJ polished nipple to extend down through its ID. A profile to receive
and hold the bushing in place is machined into the ID of the setting collar, or the
packer.
After cementing, the CSJ and bushing is retrieved with the setting tool.
FEATURES
Available for drillable for retrievable pack-off bushings

12FT, 15FT, or 20FT Seal Joints can be provided
Field adjustable shear ring for launching liner wiper plugs
35
CEMENTED LINERS
(REMEDIAL EQUIPMENT)
CEMENTED LINERS
REMEDIAL
EQUIPMENT
36
CEMENTED LINERS
company we are constantly in pursuit of new tools and innovations and we encourage anyone to contact us
with such enquiries and requests.
Reg. No. 2995

ISO 9001:2015
®
Reg. No. 11D1-0124 Reg. No. Q1-2959

37
CEMENTED LINERS
LINER TIE-BACK PACKER, ROTATIONAL (LTBPR)

UNIT 105
The TechWest Liner Tie-Back Packer (LTBPR) is a high-pressure seal at the top of a
cemented or un-cemented liner. It is run on drill pipe and/or casing and landed in a
receptacle at the top of the liner. In most applications the Tie-back Receptacle is run with
the packer providing future tie-back capability.
The LTBPR Packer is run after the liner is set, so that maximum annular flow is achieved
at the liner top during cementing.
The packer and accompanying hold-down slips are set by applying weight. The setting
tool is retrieved with the drill pipe. Once set, the packer will seal in the liner receptacle and
pack-off in the casing to isolate the liner top, holding securely pressures from above or
below. The Premium Seal Pack-Off provides a seal against high pressures and
temperatures.
FEATURES
Provides a high-pressure seal at the liner top

Safely seals micro-annular leaks at the liner top caused by high-pressure gas
Extends a liner to the surface when it is not desirable to cement the tie-back
Allows a PBR-type completion after the liner has been set and cemented by mounting
a PBR above it.
38
CEMENTED LINERS
TIEBACK RECEPTACLE POLISHING MILL (TBRP)

UNIT 322
The TechWest Tieback Receptacle Polishing Mill (TBRP) is used to dress the
inside of PBR before the running of seal assemblies or tieback packers with seal
assemblies.
The polished mill may be used immediately after cementing or prior to running
any type of tie-back seal.
FEATURES
Thoroughly cleans and polishes the tieback receptacle

Top dress mill available upon request
Connects to all standard drill stem connections
Tieback receptacle locator option to ensure polish area is clean during the
entire stroke length
39
CEMENTED LINERS
(SURFACE EQUIPMENT)
CEMENTED LINERS
SURFACE
EQUIPMENT
40
CEMENTED LINERS
(SURFACE EQUIPMENT)
Reg. No. 2995

ISO 9001:2015
®
Reg. No. 11D1-0124 Reg. No. Q1-2959

41
CEMENTED LINERS
(SURFACE EQUIPMENT)
TOP DRIVE CEMENT HEAD (TDCH)

UNIT 300
The TechWest Top Drive Cement Head (TDCH) with Ball Drop, Drill Pipe Wiper
Plug Valve and Bypass is used on rigs that employ a top-drive drilling system or
a power swivel as the drill string power source. The unit is particularly beneficial
in cementing operations when used in conjunction with rotational and
reciprocating liner assemblies. The cementing head provides a means of
introducing cement, and/or other fluids into the work string below the top-drive
unit without interrupting rotational or vertical movement. A ball drop is also
incorporated into the manifold to hold the setting ball for Hydraulic set Liner
Hangers. The manifold stores the pump down plug in its upper chamber during
the circulating, conditioning and cement mixing operations.
The TDCH is designed to support tensile loads from drill pipe

setting string and liner.
42
CEMENTED LINERS
(SURFACE EQUIPMENT)
TOP DRIVE CEMENT HEAD SKID

PRODUCT 301
The TechWest Top Drive Cement Head Skid is a heavy-duty cradle providing easy
handling, storage and operation of the Top Drive Cement Head.
FEATURES
Provides a strong solid base to protect and safely store the cementing head.
Mounted toolbox installed for operator hand tool storage
Custom company logo laser engraving available
Highly beneficial for repeated cemented liner hanger operations
43
CEMENTED LINERS
(SURFACE EQUIPMENT)
KELLY RIG CEMENT HEAD (KRCH)

UNIT 310
The TechWest Kelly Rig Cement Head (KRCH) provided with a swivel
for rotate-and-reciprocate operations with a ball-dropping ability for
setting the Hydraulic Hanger when necessary. The pump down plug is
held in the body above the lower manifold valve. Cement is first pumped
through the lower valve. When the pump down plug is needed, it is
released by opening the valve to release the pump down plug. The upper
valve is then opened, and the lower valve closed, forcing the pump down
plug out of the cementing head. It wipes residual cement from the setting
string and then seats in the Liner Wiper Plug (LWP). This LWP, in turn,
wipes the liner clean until it seats in the landing collar.
44
CEMENTED LINERS
(SURFACE EQUIPMENT)
FLAG SUB (FS)

PRODUCT 320
The TechWest Flag Sub (FS) is a surface installation that is used to indicated
when the Drill Pipe Wiper Plug (Product 111) has passed through the cementing
head.
FEATURES
Indicates when the drill pipe wipe plug has been successfully launched.
Spring loaded flag mechanism for multiple service usage
Can be installed on Kelly or Top-Drive cementing heads
Available in Standard or Premium thread connections
45
CEMENTING ACCESSORIES
CEMENTED LINERS
ACCESORIES
46
Reg. No. 2995

ISO 9001:2015
®
Reg. No. 11D1-0124 Reg. No. Q1-2959

47
NON-WELDED BOWSPRING CENTRALIZERS

UNIT 373
The TechWest Type S850 and S350 Non-Weld Bow Centralizer uses
the same style of spring design found in Type S300 centralizers. Type
S350/S850 Centralizer are available in a wide range of casing and hole
sizes and are designed to be installed over stop collars or casing collars.
NON-WELDED POSITIVE CENTRALIZERS

UNIT 374
The TechWest Type S880 and S380 Positive Centralizers are designed
to provide positive stand-off of casing inside of cased holes. The shape
of the positive bows allows for optimum fluid flow past the centralizer.
The outer diameter of the bows is supplied ¼ inch (6 mm) smaller than
the casing bore. These centralizers are designed to be installed between
Stop Collars or free floated on the casing.
48
NON-WELDED TURBOLIZER CENTRALIZER

UNIT 375
The TechWest Type S880 and S870 Non-Welded Turbolizer

Centralizers incorporate turbolating fins and integral set screws in the
lower collar to provide a secured centralizer capable of turbolating the
flow of fluid in the area directly above the turbolating fins.
The turbolizer collar end with the set screws should be the lower collar
when the centralizer is installed on the casing.
LINER CENTRALIZER
UNIT 376
The TechWest Type S310 Liner Centralizer uses a solid end band that
is installed by sliding the centralizer onto the casing. It provides minimal
annular obstruction in close tolerance holes. Used primarily in liner
completions, Type S310 liner centralizer can be supplied with integral set
screws in the lower collar or installed over Model S415 liner stop collars.
Liner Turbolizers (Model S311) are also available where additional
turbulence is desired during circulation and cementing.
49
CEMENTING PLUGS
UNIT 371
The TechWest Type S252 Top Cementing Plug and Type S253 Bottom
Cementing Plug are designed to replace conventional cementing plug
systems. By replacing the aluminum and rubber core material in
conventional plugs with a large crushable plastic core, most of the rubber
is eliminated, allowing the drill bit to fracture the plastic rather than tear
the rubber and aluminum thus significantly reducing drill out times. These
plugs are completely PDC drillable.
ALUMINIUM CORE CEMENTING PLUGS

UNIT 372
Type S255 Top Plug Aluminum Core and type S256 Bottom Plug
Aluminum Core are manufactured with an aluminum insert and are rubber
coated. The plugs are available in 4 ½ inches (114 mm) to 20 inches (208
mm). The top plug is manufactured in black natural rubber and the bottom
plug in orange with rupture diaphragm at 300 psi differential. Operating
range is up to 200°F (93°C). Plugs can be ordered in Viton® allowing for
higher operating temperatures and are operational in either synthetic or
mud fluids.
50
DEPTH ORIENTATION COLLAR

TechWest Liners’ Type S240 Depth Orientation Collar is an economical means of providing a correlation point that
can be referenced during well logging operations. The collar may be located at any point in the casing string and
provides a clean smooth bore that is compatible with the corresponding casing bore.
BELL NIPPLE
TechWest Liners’ Type S213 Bell Nipple is designed to be slipped over and welded onto the production casing
stub so that a threaded wellhead can be installed onto the bell nipple. Manufactured from seamless K-55 material
with API 8 round short threads in sizes 4 ½ inches (114.3 mm) through 7 inches (177.8 mm).
PRODUCTION CASING CAP

TechWest Liners’ slip-on cap is designed to be easily installed over the exposed top of the production casing to
prevent foreign objects from being dropped into the well after the drilling rig has moved off location and prior
to production equipment being installed. The casing cap is manufactured from steel and is installed and locked
into place with an integral set screw. Manufactured in sizes 4 ½ inches (114 mm) through 7 inches (177 mm).
BAFFLE COLLAR
TechWest Liners’ Type S245 Baffle Collar is an effective method for landing cementing plugs at specific points in
the casing string. Useful in situations such as liner cementing and where no float collar or float shoe is being run.
Cement filled collar that is easily drillable.
BAFFLE PLATE
TechWest Liners’ Type S201 Baffle Plate is used for landing cementing plugs and is designed to be installed in
the center of a casing coupling. These units are available in both aluminum and plastic materials, and come in
threaded and lush outside diameter configurations. Baffle Plates are available in sizes 4 ½ inches (114.3 mm)
through 13 inches (339.7 mm).
51
OPENHOLE LINER
EQUIPMENT
OPENHOLE
LINER
SYSTEMS
52
OPENHOLE LINER
EQUIPMENT
Reg. No. 2995

ISO 9001:2015
®
Reg. No. 11D1-0124 Reg. No. Q1-2959

53
OPENHOLE LINER
EQUIPMENT
LINER ANCHOR PACKER (LAP)

UNIT 103
The TechWest Liner Anchor Packer (LAP) is used at the top of the liner
system where both hold-up and hold-down abilities are required. This
packer comes with the ability to rotate into the well bore if tight
restrictions are likely to be encountered.
The Liner Anchor Packer is hydraulically set by the HRN or HMN running
tools while running open hole completions or multi-zone frac systems. It’s
high pressure reliable design allow for a wide variety of downhole
completion or frac well designs.
High capacity slips provide by-directional tension and compression

reliability for high hanging loads or high-pressure performance
requirements.
Anchoring and pressure integrity system for TechWest high performance

frac system.
FEATURES
Reliable economical high-pressure performance

The hydraulic release eliminates string weight free point
requirements.
Inner circulating string can be used when screen deployment is
needed.
54
OPENHOLE LINER
EQUIPMENT
HYDRAULIC ROTATING LINER RUNNING TOOL

UNIT 230
The TechWest Hydraulic Rotating Liner Running Tool (HRN), non-cementing, is used
to run and set thermal or multi zone un-cemented frac liner systems. The robust design
and rotational capabilities ensure the liner will reach TD. The tool has double internal
hydraulic pistons set the packer then disengage simply by slowly increasing hydraulic
pressure. It can also be rotated into the well bore to get through tight sections.
FEATURES
Primary setting dart, and secondary fail safe dart comes standard
Ability to pressure test the packer prior to tool disengagement
Drainage ports provide the ability to drain fluid once you have disengaged
from the packer during tripping out.
55
OPENHOLE LINER
EQUIPMENT
HYDRAULIC MECHANICAL LINER RUNNING TOOL

UNIT 231
The TechWest Hydraulic Mechanical Liner Running Tool (HMN), non-

cementing, is used to run and set multi zone un-cemented frac liner
systems hydraulically and mechanically release from the liner. Swivels as
you run in hole for increased performance.
FEATURES
Can be pushed and pulled to get the liner into position.

Hydraulic setting and mechanical release allow for an economical design.
Can be used in long ERD systems.re
Drainage ports provide the ability to drain fluid once you have disengaged from the
packer during tripping out.
56
OPENHOLE LINER
EQUIPMENT
SETTING PLUG
PRODUCT 111
The TechWest Setting Plug (SP) is designed to provide positive

displacement down a horizontally positioned running string and land in a
seat for applying pressure to the Running Tool. If the running string is
vertically orientated at the liner top, then a ball could be used with a
compatible seat.
57
OPENHOLE LINER
EQUIPMENT
OPEN HOLE HYDRAULIC INTERVAL PACKER

UNIT 142
The TechWest Open-Hole Hydraulic Interval Packer (OHHIP) is used for zone isolation in multi-zone fracturing
operations. When ran with ball opening frac sleeves they work to divert frac fluids to a pre-determined area of the
well bore. High density elastomer for high pressure frac performance securely locks the elastomer with continuous
pack-off for long term sustainable performance.
HYDRAULIC FRAC SLEEVE

UNIT 260
The TechWest Hydraulic Frac Sleeve (HFS) is used between Openhole Hydraulic Isolation Packer (OHHIP)
isolation zones and is opened hydraulically for frac operations. It is activated by circulating varying ball sizes to
the drillable ball seat.
FEATURES
System securely locks the entire mechanism

Field adjustable setting pressures for ease of operation
High pressure frac performance
Provides focused frac pressure for increased production
Economical reliable multi-zone frac system for increased savings and downhole
performance.
58
OPENHOLE LINER
EQUIPMENT
LOWER HYDRAULIC FRAC SLEEVE

UNIT 270
The TechWest Lower Hydraulic Frac Sleeve (LHFS) is the lower most frac sleeve ran in the toe section of the
well bore and is opened hydraulically for fracturing of the first zone in the well bore.
HCBS HYDRAULIC CLOSING BALL SEAT

UNIT 136
The TechWest Hydraulic Closing Ball Seat (HCBS) is used at the toe of multi zone frac string and is used to
catch the first ball dropped and close off the inside of casing for setting open-hole hydraulic packers.
FEATURES
Provides full bore ID

Reliable setting and hydraulic frac system for increased performance
High pressure frac performance for increased production
59
OPENHOLE LINER
EQUIPMENT
DEEP SERVICE TOP SEAL™

UNIT 680
The TechWest Deep Service Top Seal is designed with a focus on High Temperature
applications including SAGD (Steam Assisted Gravity Drainage), and Multi-Stage
fracturing operations. The Deep Service Top SealTM packer is a thermal variation of the
proven and reliable TechWest Liners’ Liner Lap Packer tool platform.
It is designed to be delivered downhole on the model HRN Hydraulic Rotating Running

Tool with the HydroAct™ (Hydraulic Actuator) for non-cemented applications. The HR
running tool can push, pull and rotate to the right delivering the liner through challenging
structure on the way to depth. At depth, a plug is pumped to seat allowing pressures to be
built-up in the drill pipe. At a predetermined pressure, the packer is set, and annular tests
can be conducted to verify element sealing integrity. A further increase in pressure releases
the running tool. When the running tool is pulled from the Deep Service Top Seal packer,
a set of ports are exposed allowing the drill pipe to be drained as it is pulled out of the hole.
The Deep Service Top Seal packer may be set-up in numerous configurations to suit
operational requirements.
There are versions without slips, hold-up and -down slips. For thermal applications it is
usually dressed in thermal sealing elements rated for high temperature performance.
For non-thermal applications there is the opportunity to dress the packer with Nitrile, HNBR
or HT/HP (High Pressure / High Temperature) Ecner Array® sealing elements.
While L80 metallurgy is the standard offering, other materials are readily available to meet
operational needs. Economical setting sleeves or polished bore Tieback Receptacles
maybe provided in a variety of lengths.
The Deep Service Top Seal packer also comes in a retrievable version with hold-up and -
down slips.
60
OPENHOLE LINER
EQUIPMENT
DEEP SEAL ANCHOR PACKER™

UNIT 681
The TechWest Deep Seal Anchor Packer is designed with a focus on Multi-Zone Fracturing applications and
along with the Deep Service Top Seal™ packer is our High Temperature / High Pressure, hydraulically set Anchor
Packer.
The elements are of proven High Temperature / High Pressure elastomers with the maximum available expansion
to seal in oversized holes.
The Deep Seal Anchor Packer is designed with low friction stand-off centralizer to protect and aid in deployment
of liner into the well bore, this low drag coefficient centralizer is highly beneficial in getting the liner through any
tight spots that may be encountered in the well bore.
DEEP SEAL ANCHOR™

UNIT 682
The TechWest Deep Seal Anchor is designed with a focus on Multi-Zone Fracturing applications including with
the Deep Service Top Seal™ Open Hole Tandem Seal or the Swell-Tech II™ the Deep Seal Anchor for open hole.
The Deep Seal Anchor allows the liner to be pulled into tension prior to setting of the Deep Service Top Seal this
process aids in removes any compression bends in the liner string from being push into the well bore in long ERD
liners.
This tool is also highly beneficial during fracturing operations as both end of the liner is locked into its elongated
position and aid against movement that may occur during fracturing operations.
61
OPENHOLE LINER
EQUIPMENT
TANDEM SEAL OPEN HOLE PACKER

UNIT 683
The TechWest Tandem Seal Open Hole Packer is designed with a focus on Multi-Zone
Fracturing applications and when included with the Deep Service Top Seal™ packer this
High Temperature / High Pressure packer is used for open-hole zone isolation.
It comes with dual element. The elements are of proven High Temperature / High Pressure
elastomers with the maximum available expansion to seal in oversized holes.
This packer is designed and comes with special low drag coefficient stand-off centralizers
on both ends to protect the elements and aid in deployment of liner into the well bore.
FEATURES
Tandem premium pack-off ensures zone isolation integrity under HT/HP

applications
Suitable for ERD and demanding well conditions
High pressure frac performance for increased production
62
THERMAL LINER
EQUIPMENT
THERMAL
LINER
SYSTEMS
63
THERMAL LINER
EQUIPMENT
company we are constantly in pursuit of new tools and innovations and we encourage anyone to contact
us with such enquiries and requests.
Reg. No. 2995

ISO 9001:2015
®
Reg. No. 11D1-0124 Reg. No. Q1-2959

The product information contained in this catalogue is of a general nature only and is subject to change without
notice. For the most specific and detailed technical information please contact TechWest directly.
TechWest Products and Services are subject to TechWest’s standard Terms and Conditions. Unless otherwise
noted, trademarks, servicemarks noted herein are the property of TechWest.
64
THERMAL LINER
EQUIPMENT
LINER THERMAL PACKER – RETRIEVABLE AND ROTATIONAL

PRODUCT 276
The TechWest Liner Thermal Packer (LTPRR) is a hydraulic-set, retrievable and

rotational liner hanger packer suitable for non-cemented high-temperature operations.
The LTPRR features rotating castillations on the top of the mandrel which permits the
transmission of torque to the liner string below. The packer mandrel also contains the
running thread which provides the connection to the running tool. A latch setting bore is
mounted on the top which mates with the setting sleeve on the running tool for hydraulic
actuation. A short sealing surface is provided either within the upper part of the mandrel
or via a sub on the bottom. The Thermal Element and Seals are compatible with
temperatures and pressures experienced in Thermal Heavy Oil Applications. The Packer
is supplied with a latched bore at the top for remedial purposes.
The Liner is set using a Setting Plug (Product 111), or a ball if set in the vertical and the
Hydraulic Rotating Running Tool (Product 230).
FEATURES
Retrievable thermal liner system

Built in redundancies to aid in reducing risk of operator error
OPERATION
The LTPRR is set using type HRN (Rotational) Hydraulic Setting Tool screwed into its
barrel using a left-hand thread and floating nut. When setting the packer, the setting tool
is pressured up to set and then release the thermal liner assembly.
When used to set a screen, the type PTPRR may be retrieved by running the tie-back
latch assembly with drill stem connections
65
THERMAL LINER
EQUIPMENT
LINER SAGD PACKER, ROTATIONAL (LSPR)

UNIT 102
The TechWest SAGD Packer, Rotational (LSPR) is a versatile liner high-temperature

packer that can be used in Thermal operations. Setting the LSPR Packer provides a
reliable seal between the openhole and the cased hole.
The LSPR features rotating cantillations on the top of the mandrel which permits the
transmission of torque to the liner string below. The packer mandrel also contains the
running thread which provides the connection to the running tool. A latch setting bore is
mounted on the top which mates with the setting sleeve on the running tool for hydraulic
actuation. A short sealing surface is provided either within the upper part of the mandrel
or via a sub on the bottom. The Thermal Element and Seals are compatible with
temperatures and pressures experienced in Thermal Heavy Oil Applications. The Packer
is supplied with a latched bore at the top for remedial purposes.
The Liner is set using a Setting Plug (Product 111), or a ball if set in the vertical and the
Hydraulic Rotating Running Tool (Product 230).
FEATURES
Customizable with or without hold down slips

Economical reliable design
OPERATION
The LSPR is set using type HRN (Rotational) Hydraulic Setting Tool screwed into its barrel
using a left-hand thread and floating nut. When setting the packer, the setting tool is
pressured up to set and then release the thermal liner assembly.
When used to set a screen, the type PTPRR may be retrieved by running the tie-back
latch assembly with drill stem connections
When used to set a screen, the type LLP (without hold-down slips) may be retrieved by
66
THERMAL LINER
EQUIPMENT
LINER THERMAL EXPANSION JOINT (LEJ)

UNIT 331
The TechWest Liner Thermal Expansion Joint (LEJ) is used when thermal expansion
down hole occurs from steaming operations in SAGD/CSS operations and the need to
counter that effect down hole to keep packers set and elements in good condition.
The Thermal Expansion Joint is mounted below a Rotational Liner Thermal Hanger and
torque may be transmitted through the tool when it is closed and in compression.
FEATURES
Torque is transmitted from full compression or extension

Standard 10 foot stroke, and available in different lenghts.
600F thermal presure integrity
Avaiallble in a variety of materials, and preimum threads.
OPERATION
Run to depth and space out the thermal liner string according to the anticipated
expansion/contraction required to always keep the packer in the neutral position. Set the
LTPRR or LSPR hydraulically and disconnect the running tools from the liner assembly.
67
THERMAL LINER
EQUIPMENT
MECHANICAL OPENHOLE THERMAL PACKER (MOHT)

UNIT 147
The TechWest Mechanical Open Hole Thermal Packer (MOHT) is designed to

grip and seal against open hole to isolate producing zones in high temperature
applications.
The MOHT Packer is a one trip double grip mechanical set permanent packer.
Premium surface treatment, the Pre-Squeeze mechanism, and precise
manufacturing makes the MOHT Packer to one of the most reliable permanent
packers for this specific application. MOHT Packer features the Pre-Squeeze
mechanism to eliminate any relative movement of the Soft Set Thermal Element
against open hole when packing off the element occurs.
Two MOHT Packers can be run in simultaneously with one trip. By adjusting the
quantity of shear screws on each stage of each packer, the desired sequence of
setting is achieved.
The MOHT Packer is made of materials for standard service and can be supplied
for virtually any existing well environment.
68
THERMAL LINER
EQUIPMENT
TIE BACK LATCH ASSEMBLY

UNIT 321
The TechWest Tie-back Latch Assembly (TLA) is used to latch and seal the work
string into a Tie-Back receptacle on a previously run liner. It is disconnected from
the liner with right hand rotation.
FEATURES
Retrieving configuration with drill steam connections for retrieving LTPRR

packers
Tie-back configuration to set additional liner thermal packers while mainting
full liner internal diameter
No seals required to maintain thermal capabilities
Simple snap in running procedure
69
THERMAL LINER
EQUIPMENT
THERMAL CUP STRADDLE / PACKER

UNIT 335
The TechWest Thermal Cup Straddle/Packer (TCS/P) can be used in any

number of ways and will cover any area needed with the addition of pipe between
the thermal high-temperature cups.
FEATURES
Ability to cover a large straddle gap by simply adding additional spacing joints
Two thermal cups ensure thermal pressure isolation.
Economical design
Ran with existing inner strings for increased thermal production
70
THERMAL LINER
EQUIPMENT
HYDRAULIC ROTATING LINER RUNNING TOOL

UNIT 230
The TechWest Hydraulic Rotating Liner Running Tool (HRN), non-cementing,

is used to run and set thermal or multi zone un-cemented frac liner systems. The
robust design and rotational capabilities ensure the liner will reach TD. The tool
has double internal hydraulic pistons set the packer then disengage simply by
slowly increasing hydraulic pressure. It can also be rotated into the well bore to
get through tight sections.
FEATURES
Drainage ports provide the ability to drain fluid once you have disengaged
from the packer during tripping out.
71

TechWest Liner Equipment

Uploaded by

Copyright:

Available Formats

TechWest Liner Equipment

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TechWest Liner Equipment

Uploaded by

Copyright:

Available Formats

CEMENTED LINER

CEMENTED LINERS RUNNING

CEMENTED LINERS REMEDIAL

CEMENTED LINERS ACCESORIES

OPENHOLE LINER SYSTEMS

THERMAL LINER SYSTEMS

Reg. No. 2995

Reg. No. 11D1-0124 Reg. No. Q1-2959

LINER LAP PACKER, ROTATIONAL LLPR

Customizable for licensed premium threading or materials.

A wide variety of optional configurations are available upon request.

LINER LAP PACKER, NON-ROTATIONAL (LLP)

Customizable for licensed premium threading or materials.

A wide variety of optional configurations are available upon request.

DEEP SERVICE LINER TOP PACKER™

It is designed to be delivered downhole on the model HR Hydraulic Rotating Running Tool

HYDRAULIC DOVETAIL LINER HANGER (HDLH)

HYDRAULIC DOVETAIL ROTATING LINER HANGER (HDRLH)

Enhanced fluid bypass with pocket slip design.

A wide variety of optional configurations are available upon request.

MECHANICAL SET LINER HANGER (MSLH)

The MSLH are available in right hand set only.

Economical slip design

A wide variety of optional configurations are available upon request.

MECHANICAL DOVETAIL SLIP HANGER (MDSH)

MECHANICAL DOVETAIL ROTATING SLIP HANGER (MDRSH)

Enhanced fluid bypass with dovetail design.

A wide variety of optional configurations are available upon request.

SETTING COLLAR, ROTATIONAL (SC-R)

Top clutch allows for right hand set hangers to be set.

SETTING COLLAR, NON-ROTATIONAL (SC-NR)

Drop off liner in open-hole to keep the hole open.

TIEBACK RECEPTACLE (TBR)

Comes is standard length ranging from 6 to 20 feet

TIEBACK SEAL NIPPLE (TBSN)

Provides a high-pressure seal at the liner top

TIE BACK LATCH SEAL ASSEMBLY

High pressure latch seal assembly

POSI-LATCH TIE-BACK FRAC SEAL

STAGE COLLAR (SC)

Provides improved zonal isolation

A predetermined amount of cement is then pumped through large cementing

HYDRAULIC LANDING COLLAR (HLC)

Used to set a wide variety of hydraulic liner systems

MECHANICAL PLUG LANDING COLLAR (MPLC)

Used to set a wide variety of mechanical liner systems

DRILL PIPE WIPER PLUG (DPWP)

Wipes the drill string clean after cementing operations.

LINER WIPER PLUG (LWP)

Wipes the liner clean after cementing operations.

DRILLABLE BALL SEAT COLLAR (DBSC)

Can be setup for high pressure setting capability

RETRIEVABLE PACK-OFF BUSHING (RPOB)

Provides positive seal of liner setting tools

DRILLABLE PACK OFF BUSHING (DPOB)

The TechWest Drillable Pack-off Bushing (DPOB) is a high pressure,

DRILLABLE PACK OFF BUSHING W/ FLAPPER VALVE (DPOB/F)

The TechWest Drillable Pack-off Bushing with Flapper Valve

FLOAT COLLAR (SVFC / DVFC)

VALVE FLOAT SHOE