Scribd
Upload
74 views2 pages

Int2 Eet203 MI MANICKAVASAGAM

1. This document is a summary of an internal examination for a Measurements and Instrumentation course taken on October 28, 2020. It was a 90 minute exam with 50 maximum marks. 2. The exam consisted of two parts - Part A with 5 questions worth 25 marks total, and Part B with 3 questions worth 25 marks total. 3. The questions covered topics like high dc current measurement using the Hall effect, calibration of voltmeters, ammeters and wattmeters using a potentiometer, measuring capacitance using Maxwell and Schering bridges, and determining insulation resistance using the loss of charge method.

Uploaded by

mani
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
74 views2 pages

Int2 Eet203 MI MANICKAVASAGAM

1. This document is a summary of an internal examination for a Measurements and Instrumentation course taken on October 28, 2020. It was a 90 minute exam with 50 maximum marks. 2. The exam consisted of two parts - Part A with 5 questions worth 25 marks total, and Part B with 3 questions worth 25 marks total. 3. The questions covered topics like high dc current measurement using the Hall effect, calibration of voltmeters, ammeters and wattmeters using a potentiometer, measuring capacitance using Maxwell and Schering bridges, and determining insulation resistance using the loss of charge method.

Uploaded by

mani
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

Second Internal Examination [ONLINE + OFFLINE]:OCT 2020

Dept.: ELECTRICAL AND ELECTRONICS ENGG. Semester: III


MEASUREMNTS AND
Course. Code: EET203 Course Name:
INSTRUMENTATION
Duration: 90 minutes Maximum Marks: 50
Date: 28.10.2020 SESSION AN
Marks CO PO PSO BL
PART – A
Answer ALL questions (25 marks)
1,6,1
1 a. Short notes on high dc current measurement by hall effect generator. 5 3 3,4 1
0

Explain with the help of suitable diagrams, how a D.C.Potentiometer can be used
1,5,1
b. for:(i) Calibration of Voltmeter (ii) Calibration of an Ammeter 5 3 3,4 1-3
2
(iii) Calibration of Wattmeter

(i) What are the advantages and disadvantages of a Maxwell bridge 1,5,1
c. 5 3 3,4 1-3
0
(ii) Explain how capacitance can be measured by the use of a Schering bridge 1,6,1
5 3 3,4 2
with a neat diagram and further derive the unknown capacitance at balance 0

d. Describe with the help of diagram the loss of charge method for determining the 5 3 3,4 3 2
insulation resistance of a length of a cable.
PART – B
Answer ALL questions (25 marks)

Explain the constructional features of a flux meter. Show that for a flux meter
N E = K (Ѳ2 – Ѳ1) , Where N is the number of turns on the search coil used, _ is 1,6,1
2. a. 7 4 3,4 1
change in flux, Ѳ1 is the initial reading in the flux meter and Ѳ2 is the final 0
reading in the flux meter and K is a constant.
Explain the “Lloyd Fisher square “method of measuring iron losses in 1,5,1
b. 5 4 3,4 1-3
ferromagnetic material. 2
Explain with the help of a neat diagram, a method for the determination of B-H
1,5,1
c. Curve of a magnetic sample. Point out various sources of errors and methods of 8 4 4 1-3
0
minimizing them
Explain with neat sketch of measurement of illumination by pohoto conductive 1,6,1
e 5 4 1,2 2
transducer. 0

You might also like