Scribd
Upload
44 views1 page

ST100 Series SIL Declaration of Conformity (23EN000025)

Uploaded by

heikel

The ST100 Series of flow, temperature, and pressure measurement products from Fluid Components International is suitable for use in a safety instrumented system for Safety Integrity Level 1. An analysis by exida classified the ST100 Series as a Type B subsystem with a hardware fault tolerance of 0. The analysis results in failure rates that achieve a SIL 1 rating for the ST100 Series as a single device. The declaration is signed and dated by an Engineering Manager at Fluid Components International.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt

ST100 Series SIL Declaration of Conformity (23EN000025)

Uploaded by

heikel
44 views1 page
The ST100 Series of flow, temperature, and pressure measurement products from Fluid Components International is suitable for use in a safety instrumented system for Safety Integrity Level 1. An analysis by exida classified the ST100 Series as a Type B subsystem with a hardware fault tolerance of 0. The analysis results in failure rates that achieve a SIL 1 rating for the ST100 Series as a single device. The declaration is signed and dated by an Engineering Manager at Fluid Components International.

Original Title

ST100-Series-SIL-Declaration-of-Conformity-(23EN000025)

Copyright

© © All Rights Reserved

Available Formats

PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

The ST100 Series of flow, temperature, and pressure measurement products from Fluid Components International is suitable for use in a safety instrumented system for Safety Integrity Level 1. An analysis by exida classified the ST100 Series as a Type B subsystem with a hardware fault tolerance of 0. The analysis results in failure rates that achieve a SIL 1 rating for the ST100 Series as a single device. The declaration is signed and dated by an Engineering Manager at Fluid Components International.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
44 views1 page

ST100 Series SIL Declaration of Conformity (23EN000025)

Uploaded by

heikel
The ST100 Series of flow, temperature, and pressure measurement products from Fluid Components International is suitable for use in a safety instrumented system for Safety Integrity Level 1. An analysis by exida classified the ST100 Series as a Type B subsystem with a hardware fault tolerance of 0. The analysis results in failure rates that achieve a SIL 1 rating for the ST100 Series as a single device. The declaration is signed and dated by an Engineering Manager at Fluid Components International.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 1

SIL DECLARATION OF CONFORMITY Model ST100 SERIES

We, Fluid Components International LLC, located at 1755 La Costa Meadows Drive, San Marcos, California 92078-
5115 USA, declare as manufacturer, that the ST100 Series of products is suitable for use in a safety instrumented
system for SIL 1, flow, temperature and pressure measurement.

The ST100 Series has been classified as Type B subsystem according to IEC 61508-1 Chapter 7.4.4.1.3 with a
Hardware tolerance (HFT) of 0.

The Failure Modes, Effects and Diagnostic Analysis (FMEDA) report carried out by exida, resulted in following
failure ratings:

SIL (Safety Integrity Level) : 1 - As a single device


HFT (Hardware Fault Tolerance) : 0
Subsystem type : B

Failure rates according to IEC 61508-1


Function SFF PFD (AVG) λDU λDD λSU λSD
-2
Single Probe AC supply 79.8 % 1.21 x 10 567 FIT 1927 FIT 314 FIT 0
Single Probe DC supply 79.9 % 1.22 x 10 -2 570 FIT 1946 FIT 317 FIT 0
-2
Dual Probe AC supply 88.9% 1.00 x 10 415 FIT 2918 FIT 404 FIT 0
Dual Probe DC supply 88.9% 1.01 x 10 -2 418 FIT 2937 FIT 407 FIT 0

Terminology:
SFF = Safe Failure fraction
PFD = Probability of failure on demand
λDU = failure rate dangerous undetected faults
λDD = failure rate dangerous detected faults
λSU = failure rate safe undetected faults
λSD = failure rate safe detected faults
FIT = Failure Rate in 10-9 /hour

Above analysis is based on assuming:


 The HART protocol is used for setup, calibration and diagnostics purposes, not for safety critical function.
 Materials are compatible with process conditions.
 The device is installed per manufacturer’s instructions.
 External power supply failure rates are not included.
 Worst-case internal fault detection time is 1 hour.
 The device is configured for fault detection per NAMUR NE43 or the logic solver is configured to interpret
output fault conditions.
 Proof test interval of 1 year.
Issued at San Marcos, California USA
20, May 2012
Eric Wible
2012.06.28 15:47:50 -07'00'
______________________________________
Eric Wible, Engineering Manager

Flow/Liquid Level/Temperature Instrumentation


Visit FCI on the Worldwide Web: www.fluidcomponents.com
1755 La Costa Meadows Drive, San Marcos, California 92078 USA 760-744-6950  800-854-1993  760-736-6250
European Office: Persephonestraat 3-01 5047 TTTilburg – The Netherlands – Phone 31-13-5159989  Fax 31-13-5799036

Doc no. 23EN000025-

You might also like