Quick Setup Guide: France
Quick Setup Guide: France
This is 1D&2D plug and play model if you use a US keyboard. If you use other type of
keyboard, plug the USB cable on your device , setup keyboard language before you use
it. (refer to below Keyboard Language Type) after that the scanner can start to work.
Barcode Programming
Netum barcode scanners are factory programmed for the most common terminal and
communications settings. If you need to change these settings, programming is
accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option
indicates the default setting.
Keyboard layouts vary from country to country. The default setting is U.S. keyboard.
In order to let scanner upload the codes in a correct way, you have to set the keyboard
language.
For example If you use French Keyboard, scan below barcode of “French keyboard”.
Then the scanner will upload barcodes according to French keyboard layout. American
Keyboard is set by default, if you use a US keyboard you can ignore this part.
France Germany
Italy Spain
Turkey Hungary
Interface (Optional)
USB Interface
USB HID-KBW
When you connect the scanner to the Host via a USB connection, you can enable the
USB HID-KBW feature by scanning the barcode below. It works on a Plug and Play basis
and no driver is required.
If you connect scanner to the Host via a USB connection, the USB COM Port Emulation
feature allows the Host to receive data in the way as a serial port does.
RS232 Interface
RS232
Scanning the following barcode can restore the scanner to the factory defaults.
Terminator
The scanner provides a shortcut for setting the terminating character suffix to CR or
CRLF and enabling it by scanning the appropriate barcode below.
Beep Notification
Beep Volume can be configurated by scanning the appropriate barcode below.
1.6KHz 2.4KHz
3.5KHz Mute
Aiming
When scanning/capturing image, the engine projects an aiming pattern which allows
positioning the target barcode within its field of view and thus makes decoding easier.
UPC/EAN
*Enable Disable
Codabar
*Enable Disable
*Enable Disable
Code 32
*Enable Disable
Full ASII Code39
Enable *Disable
Interleaved 2 of 5
*Enable Disable
Code 93
Enable * Disable
Straight 2 of 5 Industrial
Enable * Disable
Matrix 2 of 5
Enable * Disable
Code 11
Enable * Disable
Code 128
*Enable Disable
Telepen
*Enable Disable
UPC-A
*Enable Disable
EAN-13
*Enable Disable
EAN-8
*Enable Disable
MSI
*Enable Disable
GS1 DataBar Omnidirectional
*Enable Disable
Enable * Disable
Enable * Disable
Important Note: Above programming barcodes only applies for 1D barcode. If you
want to enable the scanner to read inverse 2D codes, first find the type of 2D barcodes
from below 2D Symbologies then read the relevant programming code to enable it.
Please refer to the specific type of 2D barcode to enable the scanner reading Inverse 2D
barcodes
2D Symbologies
PDF417
*Enable Disable
MicroPDF417
Enable * Disable
QR Code
*Enable Disable
Micro QR Code
Enable * Disable
Enable Invert Micro QR Scan *Disable Invert Micro QR Scan
Enable * Disable
Enable Invert Data Matrix Scan *Disable Invert Data Matrix Scan
Aztec Code
Enable * Disable
Enable * Disable
MaxiCode
Enable * Disable
Enable * Disable
Program the Custom Prefix & Suffix
1.Scan “Enter Setup” barcode to make the device into programming mode.
4.Scan “Exit Setup” barcode to make the device exit programming mode.
1.Scan “Enter Setup” barcode to make the device into programming mode.
4.Scan “Exit Setup” barcode to make the device exit programming mode.
Custom several prefixs
Example 3
Custom prefix of “$” and ”@”
1.Scan “Enter Setup” barcode to make the device into programming mode.
6. Scan “Exit Setup” barcode to make the device exit programming mode.
Example 4
Custom suffix of “$” and ”@”
1.Scan “Enter Setup” barcode to make the device into programming mode.
6. Scan “Exit Setup” barcode to make the device exit programming mode.
“Enter Setup” “Exit Setup”
20 /
Appendix 2: ASCII TABLE
Value Char. Value Char. Vaule Char. Value Char.
21 /
023 ETB 055 7 087 W 119 w
22 /