Scribd
Upload
382 views13 pages

Example1 Gauss Seidel Details

This document provides an example of using the Gauss-Seidel method to solve a 3-bus power flow problem. It includes determining the voltage phasors at buses 2 and 3 using iterative calculations. It also includes calculating the real and reactive power at the slack bus, the line flows between buses, and line losses. The example is worked through in 9 steps, showing the calculations and culminating in a one-line diagram depicting the results.

Uploaded by

Nor Hanaros
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
382 views13 pages

Example1 Gauss Seidel Details

This document provides an example of using the Gauss-Seidel method to solve a 3-bus power flow problem. It includes determining the voltage phasors at buses 2 and 3 using iterative calculations. It also includes calculating the real and reactive power at the slack bus, the line flows between buses, and line losses. The example is worked through in 9 steps, showing the calculations and culminating in a one-line diagram depicting the results.

Uploaded by

Nor Hanaros
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

GAUSS

SEIDEL
EXAMPLE 1 (SLACK
BUS AND PQ BUS)

Example 1 Gauss Seidel|


AziahKhamisV1_2020
EXAMPLE 1
Figure below shows the one-line diagram of a simple three-bus power
system with generation at bus 1. The magnitude of voltage at bus 1 is
adjusted to 1.05 per unit. The scheduled loads at buses 2 and 3 are as
marked on the diagram. Line impedances are marked in per unit on a
100-MVA base and the line charging susceptances are neglected.

1) Using the Gauss-Seidel method, determine the phasor values of


the voltage at the load buses 2 and 3 (P-Q buses) accurate to
four decimal places.
2) Find the slack bus real and reactive power.
3) Determine the line flow and line losses. Construct a power
flow diagram showing the direction of line flow.

Example 1 Gauss Seidel|


AziahKhamisV1_2020
STEP1: TYPE OF BUS
B1 B2 B3 NEXT

✓
STEP
Voltage, |V |
Phase angle, δ ✓
S
Real power, P ✓ ✓
Reactive power, Q ✓ ✓ PQ
BUS

FROM THE TABLE AND THE QUESTION:


V1= SLACK BUS
SO WE NEED TO FIND V2 AND V3. (USING GAUSS
SEIDEL METHOD)

Example 1 Gauss Seidel|


AziahKhamisV1_2020
STEP 2: IMPEDANCE TO ADMITTANCE

yij IMPEDANCE ADMITTANCE


y12 0.02+j0.04
y13 0.01+j0.03
y23 0.0125+j0.025

Example 1 Gauss Seidel|


AziahKhamisV1_2020
STEP 3: S IN PER UNIT
P Q
S2 256.6 j110.2 NOTE THAT SBASE
S3 138.6 j45.2 GIVEN IN QUESTION IS
100MVA.

NEXT

Example 1 Gauss Seidel|


AziahKhamisV1_2020
V 3
STEP 4: CALCULATE Vi
Assume initial V for V(2)(0) = V(3)(0) =1+j0; GIVEN THAT V(1) =1.05 Recall
information

* S2sch,
S3sch

Example 1 Gauss Seidel| V(2)(2)


AziahKhamisV1_2020 V(3)(2)
STEP 4: CALCULATE Vi
Continue solving V(2)(2) and V(3)(2) by taking V(2)(1) and V(3)(1) value from the
calculation
V(2)(1)
V(3)(1)

Example 1 Gauss Seidel|


AziahKhamisV1_2020
STEP 4: CALCULATE Vi
Continue solving V(2)(3) and V(3)(3) by taking V(2)(2) and V(3)(2) value from the calculation and repeat until error = 5x10-5

Therefore,

Example 1 Gauss Seidel|


AziahKhamisV1_2020
STEP 5: CALCULATE S AT SLACK BUS
Recall
information

the slack bus real and reactive powers are

P1 = 4.095 pu = 409.5 MW
and
Q1 = 1.890 pu = 189 Mvar.

Example 1 Gauss Seidel|


AziahKhamisV1 2020
STEP 6: CALCULATE LINE CURRENT

Y 1 2
Y 2 1

The line flows are:

DRAW
Example 1 Gauss Seidel|
AziahKhamisV1 2020
STEP 7: CALCULATE LINE FLOW

The line flows are:

DRAW
Example 1 Gauss Seidel|
AziahKhamisV1 2020
STEP 8: CALCULATE LOSSES

DRAW
Example 1 Gauss Seidel|
AziahKhamisV2 2020
P

STEP 9: DRAW DIAGRAM Q

LINE
FLOW

LOSSESS

Example 1 Gauss Seidel|


AziahKhamisV1_2020

You might also like