DRC.

4720 BRIDGESENSOR
Description:
The unit is a DIN Rail mount, self-contained DC
powered module designed for load cell, strain gage, or
single ended use. lt contains a precision instrumentation
amplifier, filtered output and a built-in 10VDC excitation
supply capable of driving a 350 ohm bridge. The 0 to
30mV input range makes it compatible with most strain
gage based load cell or pressure transducer outputs.
It prcvides an output of 4 to 20mA. Connections are
made ,ria easily accessible screw clamp terminal blocks.
Zero and Span adjustment potentiometers are located
externarlv as weil for easy access. Contact the factory
for acc :;cnal gain/output options.

Features:

Amplifier Bridge Supply

Gain Fixed Output +1oVDC t1%
lnput for a 20mA OutDut 1OmV to 30mV
Temperature Coeffi cient 0.0596 I "C
10,01
Load Current 30mA Max
23''-l !1ax Output
Power Requirements
:45% I "C
Voltage 18 to 26 VDC
t70pV
aTpV loC input Current (1 - 350 Ohm Bndge) 55 mA
3 to +5 VDC Environment
Common Mode Rejectlon - DC 100d8 Operating Temperature OoC to +55oC
lnput Noise Storage Temperature -40oC to +80oC
0.1 Hz to 1 OHz 0.3pV pp Typ
Size
Output
Size
Output Range Not including Universal Foot for 1.65"H x 1.06"W x 3.78"1
4 to 20mA (42x27 x 96mm)
standard DIN EN Rails)
Compliance Voltage 5,5V Max
/Veight 3 oz. (859)
Loop Resistance 250Q Max
Agency Approval
Frequency Response
2 Pole Filter DC to 1OHz UL UL508, C22.2 Pending
Total RMS Gain oC
Temperature Coeffi cient 0.007o/o I

Shop Online at
omeoa.com
omega.com@ e- m a i I : i nfo@o m ed a. c o
For latest profrct minualg:
m
6megamanual.info
10t1t09, Eco 101013-2, 101108-3
 DRC.4720 BRIDGESENSOR
FULL BRIDGE CONNECTION
SIRI.\ :TGE TC VOLTAGE

35Or) BRIDCE

4-20 mA

- COM

DC POWER

+24V

SINGLE ENDED
F:
'tr
-:
,:--.':',-liON
:r:_:-:?

: IIDGE
:(:i-ATtoN
: - PPLY

Getting Started C. Connect a current mete. across the output, pins 5 and
D. Adjust the Zero Adjustment potentiometer for the
6.

'. -ccK Uc Prccedure desired zero current,

A. Connect the +out of the load cell to the +lNpUT, pin 4. E. Remove the jumper from the +INPUT and -lNpUT
B. Connect the -out of the load cell to the -lNpUT, pin 3. terminals.
C. Connect the +excitation of the load cell to +EXCITATION, F. With no load on the load cell, readjust the zero output.
pin '1. G. Apply a known load to the load cell; in most cases it
D. Connect the -excitation of the load cell to -EXCITATION, would be 100% of full scale.
pin 2. H. Adjust the SPAN ADJUSTMENT potentiometer for the
E. Connect the +24 VDC power supply to +24V pin g and desired full scale output current.
COM, pin 7. l. Repeat steps F thru H until the desired settings are
obtained.
2. Turn on Procedure
A. Verify that the hook up procedure is complete.
B. Turn on the +24 VDC power source connected to the
mn -]
unit.
irir
ON FULL SCALE
sw1.'l SW,I.2
OFF LOAD CELL INPUT
3. Calibration Procedure
A. Jumper the +INPUT and the -INPUT terminals, pins 3
--T-7' l

OFF OFF 30 mV

and 4, together. ON OFF 20 mV

B. Check the Gain Switch Table, and set SWl-1 and SW1-2 ON ON 10 mV
to the expected full scale output of the load cell.

omega.com@
 DRC.4720 BRIDGESENSOR

OUTPUT I-ABEL
^ ^^n
a,uv
l

,\'rliSA" -;C: ::r-

STANDARD DIN tN RAILS

Mechanical toieral..3s unless otherwise noted:

X.XX dimensions :-120 inches

X.XXX dimensiors :1.105 inches

TERMINAL FUNCTION TERMINAL FUNCTION

SW1-1, SW1.2 GAIN SWITCHES 5 +OUTPUT
SPAN SPAN ADJUSTIVIENT b COM
1 +EXCITATION 7 COM
2 - EXCITATION I +24V
3 - INPUT ZERO ZERO ADJUSTIvIENT
4 +INPUT

omega.com@
3