The document provides design calculations for C-purlins under a roof, including:
1) Section properties and geometry of the C-purlins.
2) Layout of the roof framing and purlins.
3) Material properties and loads on the roof.
4) Strength calculations to check the purlins will not yield or buckle under the loads.
5) Serviceability calculations to check deflection limits are not exceeded.
The document provides design calculations for C-purlins under a roof, including:
1) Section properties and geometry of the C-purlins.
2) Layout of the roof framing and purlins.
3) Material properties and loads on the roof.
4) Strength calculations to check the purlins will not yield or buckle under the loads.
5) Serviceability calculations to check deflection limits are not exceeded.
The document provides design calculations for C-purlins under a roof, including:
1) Section properties and geometry of the C-purlins.
2) Layout of the roof framing and purlins.
3) Material properties and loads on the roof.
4) Strength calculations to check the purlins will not yield or buckle under the loads.
5) Serviceability calculations to check deflection limits are not exceeded.
The document provides design calculations for C-purlins under a roof, including:
1) Section properties and geometry of the C-purlins.
2) Layout of the roof framing and purlins.
3) Material properties and loads on the roof.
4) Strength calculations to check the purlins will not yield or buckle under the loads.
5) Serviceability calculations to check deflection limits are not exceeded.
Linear weight ω 0.03 x-coordinate of the section centroid xbar 14.92 y-coordinate of the section centroid ybar 62.50
Moment of inertia about x-axis Ix 897,161.88
Elastic modulus about x-axis Sx 14,354.59 Radius of gyration about x-axis rx 49.61 Plastic modulus about x-axis Zx 16,600.13
Moment of inertia about y-axis Iy 120,399.84
Elastic modulus about y-axis Sy 3,432.23 Radius of gyration about y-axis ry 18.17 Location of plastic neutral axis from left end xp 30.63 Plastic modulus about y-axis Zy 8,023.73
2 | Roof framing layout
Distance between rafters/trusses L 3.00 Length of overhang Lc 1.20 Spacing of purlins s 0.60 Location of sagrods (1 = no sagrod, 2 = sagrods @ midpoints, 3 = sagrods @ third points) sagrods 1.00 Roof angle θ 8.00 3 | Material properties Yield strength Fy 248.00 Ultimate strength Fu 400.00 Modulus of elasticity E 200,000.00
Moment of inertia of one flange about y-axis If 15,625.00 Warping constant Cw 122,070,313 Distance between flange centroids ho 123.50 Torsional constant modification factor c 1.94 Radius of gyration of section effective in lateral torsional buckling about y-axis rts 16.34 Torsional constant J 273.38 Critical length for compactness Lp 908.38 Critical length for slenderness Lr 1,863.23 Effective length about the x-axis Lb 3,000.00 Moment gradient factor Cb 1.14 Critical bending stress Fcr 88.96 Nominal moment capacity Mn 1.28
Ultimate moment capacity about major axis φMnx 1.15
Minor axis bending
Case 1: Yielding Nominal moment capacity Mn 1.36
Case 2: Flange local buckling
Critical slenderness ratio for compactness λp 10.79 Critical slenderness ratio for slenderness λr 28.40 Slenderness ratio λ 32.33 Nominal moment capacity Mn 1.71
Ultimate moment capacity about minor axis φMny 1.23
